1 files changed, 0 insertions, 97 deletions
diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt
deleted file mode 100644
index 0c398581d52b..000000000000
--- a/Documentation/devicetree/bindings/sound/rt5640.txt
+++ /dev/null
@@ -1,97 +0,0 @@
-RT5640/RT5639 audio CODEC
-
-This device supports I2C only.
-
-Required properties:
-
-- compatible : One of "realtek,rt5640" or "realtek,rt5639".
-
-- reg : The I2C address of the device.
-
-- interrupts : The CODEC's interrupt output.
-
-Optional properties:
-
-- clocks: The phandle of the master clock to the CODEC
-- clock-names: Should be "mclk"
-
-- realtek,in1-differential
-- realtek,in2-differential
-- realtek,in3-differential
-  Boolean. Indicate MIC1/2/3 input are differential, rather than single-ended.
-
-- realtek,lout-differential
-  Boolean. Indicate LOUT output is differential, rather than stereo.
-
-- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
-
-- realtek,dmic1-data-pin
-  0: dmic1 is not used
-  1: using IN1P pin as dmic1 data pin
-  2: using GPIO3 pin as dmic1 data pin
-
-- realtek,dmic2-data-pin
-  0: dmic2 is not used
-  1: using IN1N pin as dmic2 data pin
-  2: using GPIO4 pin as dmic2 data pin
-
-- realtek,jack-detect-source
-  u32. Valid values:
-  0: jack-detect is not used
-  1: Use GPIO1 for jack-detect
-  2: Use JD1_IN4P for jack-detect
-  3: Use JD2_IN4N for jack-detect
-  4: Use GPIO2 for jack-detect
-  5: Use GPIO3 for jack-detect
-  6: Use GPIO4 for jack-detect
-
-- realtek,jack-detect-not-inverted
-  bool. Normal jack-detect switches give an inverted signal, set this bool
-  in the rare case you've a jack-detect switch which is not inverted.
-
-- realtek,over-current-threshold-microamp
-  u32, micbias over-current detection threshold in µA, valid values are
-  600, 1500 and 2000µA.
-
-- realtek,over-current-scale-factor
-  u32, micbias over-current detection scale-factor, valid values are:
-  0: Scale current by 0.5
-  1: Scale current by 0.75
-  2: Scale current by 1.0
-  3: Scale current by 1.5
-
-Pins on the device (for linking into audio routes) for RT5639/RT5640:
-
-  * DMIC1
-  * DMIC2
-  * MICBIAS1
-  * IN1P
-  * IN1N
-  * IN2P
-  * IN2N
-  * IN3P
-  * IN3N
-  * HPOL
-  * HPOR
-  * LOUTL
-  * LOUTR
-  * SPOLP
-  * SPOLN
-  * SPORP
-  * SPORN
-
-Additional pins on the device for RT5640:
-
-  * MONOP
-  * MONON
-
-Example:
-
-rt5640 {
-	compatible = "realtek,rt5640";
-	reg = <0x1c>;
-	interrupt-parent = <&gpio>;
-	interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_HIGH>;
-	realtek,ldo1-en-gpios =
-		<&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
-};