diff options
Diffstat (limited to 'Documentation/devicetree/bindings/sound')
9 files changed, 110 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/sound/cs4349.txt b/Documentation/devicetree/bindings/sound/cs4349.txt new file mode 100644 index 000000000000..54c117b59dba --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4349.txt @@ -0,0 +1,19 @@ +CS4349 audio CODEC + +Required properties: + + - compatible : "cirrus,cs4349" + + - reg : the I2C address of the device for I2C + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. + +Example: + +codec: cs4349@48 { + compatible = "cirrus,cs4349"; + reg = <0x48>; + reset-gpios = <&gpio 54 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/ics43432.txt b/Documentation/devicetree/bindings/sound/ics43432.txt new file mode 100644 index 000000000000..b02e3a6c0fef --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ics43432.txt @@ -0,0 +1,17 @@ +Invensense ICS-43432 MEMS microphone with I2S output. + +There are no software configuration options for this device, indeed, the only +host connection is the I2S interface. Apart from requirements on clock +frequency (460 kHz to 3.379 MHz according to the data sheet) there must be +64 clock cycles in each stereo output frame; 24 of the 32 available bits +contain audio data. A hardware pin determines if the device outputs data +on the left or right channel of the I2S frame. + +Required properties: + - compatible : Must be "invensense,ics43432" + +Example: + + ics43432: ics43432 { + compatible = "invensense,ics43432"; + }; diff --git a/Documentation/devicetree/bindings/sound/max98357a.txt b/Documentation/devicetree/bindings/sound/max98357a.txt index a7a149a236e5..28645a2ff885 100644 --- a/Documentation/devicetree/bindings/sound/max98357a.txt +++ b/Documentation/devicetree/bindings/sound/max98357a.txt @@ -4,7 +4,11 @@ This node models the Maxim MAX98357A DAC. Required properties: - compatible : "maxim,max98357a" -- sdmode-gpios : GPIO specifier for the GPIO -> DAC SDMODE pin + +Optional properties: +- sdmode-gpios : GPIO specifier for the chip's SD_MODE pin. + If this option is not specified then driver does not manage + the pin state (e.g. chip is always on). Example: diff --git a/Documentation/devicetree/bindings/sound/mt8173-max98090.txt b/Documentation/devicetree/bindings/sound/mt8173-max98090.txt index 829bd26d17f8..519e97c8f1b8 100644 --- a/Documentation/devicetree/bindings/sound/mt8173-max98090.txt +++ b/Documentation/devicetree/bindings/sound/mt8173-max98090.txt @@ -3,11 +3,13 @@ MT8173 with MAX98090 CODEC Required properties: - compatible : "mediatek,mt8173-max98090" - mediatek,audio-codec: the phandle of the MAX98090 audio codec +- mediatek,platform: the phandle of MT8173 ASoC platform Example: sound { compatible = "mediatek,mt8173-max98090"; mediatek,audio-codec = <&max98090>; + mediatek,platform = <&afe>; }; diff --git a/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt index 61e98c976bd4..f205ce9e31dd 100644 --- a/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt +++ b/Documentation/devicetree/bindings/sound/mt8173-rt5650-rt5676.txt @@ -3,11 +3,13 @@ MT8173 with RT5650 RT5676 CODECS Required properties: - compatible : "mediatek,mt8173-rt5650-rt5676" - mediatek,audio-codec: the phandles of rt5650 and rt5676 codecs +- mediatek,platform: the phandle of MT8173 ASoC platform Example: sound { compatible = "mediatek,mt8173-rt5650-rt5676"; mediatek,audio-codec = <&rt5650 &rt5676>; + mediatek,platform = <&afe>; }; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index b6b3a786855f..1173395b5e5c 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -18,6 +18,12 @@ Required properties: - rcar_sound,src : Should contain SRC feature. The number of SRC subnode should be same as HW. see below for detail. +- rcar_sound,ctu : Should contain CTU feature. + The number of CTU subnode should be same as HW. + see below for detail. +- rcar_sound,mix : Should contain MIX feature. + The number of MIX subnode should be same as HW. + see below for detail. - rcar_sound,dvc : Should contain DVC feature. The number of DVC subnode should be same as HW. see below for detail. @@ -90,6 +96,22 @@ rcar_sound: sound@ec500000 { }; }; + rcar_sound,mix { + mix0: mix@0 { }; + mix1: mix@1 { }; + }; + + rcar_sound,ctu { + ctu00: ctu@0 { }; + ctu01: ctu@1 { }; + ctu02: ctu@2 { }; + ctu03: ctu@3 { }; + ctu10: ctu@4 { }; + ctu11: ctu@5 { }; + ctu12: ctu@6 { }; + ctu13: ctu@7 { }; + }; + rcar_sound,src { src0: src@0 { interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt index c64155027288..962748a8d919 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt @@ -6,6 +6,7 @@ Required properties: - compatible : "renesas,rsrc-card,<board>" Examples with soctypes are: + - "renesas,rsrc-card" - "renesas,rsrc-card,lager" - "renesas,rsrc-card,koelsch" Optional properties: @@ -29,6 +30,12 @@ Optional subnode properties: - frame-inversion : bool property. Add this if the dai-link uses frame clock inversion. - convert-rate : platform specified sampling rate convert +- audio-prefix : see audio-routing +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources. + use audio-prefix if some components is using same sink/sources naming. + it can be used if compatible was "renesas,rsrc-card"; Required CPU/CODEC subnodes properties: diff --git a/Documentation/devicetree/bindings/sound/rockchip-max98090.txt b/Documentation/devicetree/bindings/sound/rockchip-max98090.txt new file mode 100644 index 000000000000..a805aa99ad75 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip-max98090.txt @@ -0,0 +1,19 @@ +ROCKCHIP with MAX98090 CODEC + +Required properties: +- compatible: "rockchip,rockchip-audio-max98090" +- rockchip,model: The user-visible name of this sound complex +- rockchip,i2s-controller: The phandle of the Rockchip I2S controller that's + connected to the CODEC +- rockchip,audio-codec: The phandle of the MAX98090 audio codec +- rockchip,headset-codec: The phandle of Ext chip for jack detection + +Example: + +sound { + compatible = "rockchip,rockchip-audio-max98090"; + rockchip,model = "ROCKCHIP-I2S"; + rockchip,i2s-controller = <&i2s>; + rockchip,audio-codec = <&max98090>; + rockchip,headset-codec = <&headsetcodec>; +}; diff --git a/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt b/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt new file mode 100644 index 000000000000..411a62b3ff41 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt @@ -0,0 +1,17 @@ +ROCKCHIP with RT5645/RT5650 CODECS + +Required properties: +- compatible: "rockchip,rockchip-audio-rt5645" +- rockchip,model: The user-visible name of this sound complex +- rockchip,i2s-controller: The phandle of the Rockchip I2S controller that's + connected to the CODEC +- rockchip,audio-codec: The phandle of the RT5645/RT5650 audio codec + +Example: + +sound { + compatible = "rockchip,rockchip-audio-rt5645"; + rockchip,model = "ROCKCHIP-I2S"; + rockchip,i2s-controller = <&i2s>; + rockchip,audio-codec = <&rt5645>; +}; |