diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 145 |
1 files changed, 0 insertions, 145 deletions
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt deleted file mode 100644 index cfc9f40ab641..000000000000 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ /dev/null @@ -1,145 +0,0 @@ -* USB2 ChipIdea USB controller for ci13xxx - -Required properties: -- compatible: should be one of: - "fsl,imx23-usb" - "fsl,imx27-usb" - "fsl,imx28-usb" - "fsl,imx6q-usb" - "fsl,imx6sl-usb" - "fsl,imx6sx-usb" - "fsl,imx6ul-usb" - "fsl,imx7d-usb" - "fsl,imx7ulp-usb" - "lsi,zevio-usb" - "qcom,ci-hdrc" - "chipidea,usb2" - "xlnx,zynq-usb-2.20a" -- reg: base address and length of the registers -- interrupts: interrupt for the USB controller - -Recommended properies: -- phy_type: the type of the phy connected to the core. Should be one - of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this - property the PORTSC register won't be touched. -- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" - -Deprecated properties: -- usb-phy: phandle for the PHY device. Use "phys" instead. -- fsl,usbphy: phandle of usb phy that connects to the port. Use "phys" instead. - -Optional properties: -- clocks: reference to the USB clock -- phys: reference to the USB PHY -- phy-names: should be "usb-phy" -- vbus-supply: reference to the VBUS regulator -- maximum-speed: limit the maximum connection speed to "full-speed". -- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts -- itc-setting: interrupt threshold control register control, the setting - should be aligned with ITC bits at register USBCMD. -- ahb-burst-config: it is vendor dependent, the required value should be - aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This - property is used to change AHB burst configuration, check the chipidea - spec for meaning of each value. If this property is not existed, it - will use the reset value. -- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword - (4 bytes), This register represents the maximum length of a the burst - in 32-bit words while moving data from system memory to the USB - bus, the value of this property will only take effect if property - "ahb-burst-config" is set to 0, if this property is missing the reset - default of the hardware implementation will be used. -- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword - (4 bytes), This register represents the maximum length of a the burst - in 32-bit words while moving data from the USB bus to system memory, - the value of this property will only take effect if property - "ahb-burst-config" is set to 0, if this property is missing the reset - default of the hardware implementation will be used. -- extcon: phandles to external connector devices. First phandle should point to - external connector, which provide "USB" cable events, the second should point - to external connector device, which provide "USB-HOST" cable events. If one - of the external connector devices is not required, empty <0> phandle should - be specified. -- phy-clkgate-delay-us: the delay time (us) between putting the PHY into - low power mode and gating the PHY clock. -- non-zero-ttctrl-ttha: after setting this property, the value of register - ttctrl.ttha will be 0x7f; if not, the value will be 0x0, this is the default - value. It needs to be very carefully for setting this property, it is - recommended that consult with your IC engineer before setting this value. - On the most of chipidea platforms, the "usage_tt" flag at RTL is 0, so this - property only affects siTD. - If this property is not set, the max packet size is 1023 bytes, and if - the total of packet size for pervious transactions are more than 256 bytes, - it can't accept any transactions within this frame. The use case is single - transaction, but higher frame rate. - If this property is set, the max packet size is 188 bytes, it can handle - more transactions than above case, it can accept transactions until it - considers the left room size within frame is less than 188 bytes, software - needs to make sure it does not send more than 90% - maximum_periodic_data_per_frame. The use case is multiple transactions, but - less frame rate. -- mux-controls: The mux control for toggling host/device output of this - controller. It's expected that a mux state of 0 indicates device mode and a - mux state of 1 indicates host mode. -- mux-control-names: Shall be "usb_switch" if mux-controls is specified. -- pinctrl-names: Names for optional pin modes in "default", "host", "device". - In case of HSIC-mode, "idle" and "active" pin modes are mandatory. In this - case, the "idle" state needs to pull down the data and strobe pin - and the "active" state needs to pull up the strobe pin. -- pinctrl-n: alternate pin modes - -i.mx specific properties -- fsl,usbmisc: phandler of non-core register device, with one - argument that indicate usb controller index -- disable-over-current: disable over current detect -- over-current-active-low: over current signal polarity is active low. -- over-current-active-high: over current signal polarity is active high. - It's recommended to specify the over current polarity. -- power-active-high: power signal polarity is active high -- external-vbus-divider: enables off-chip resistor divider for Vbus - -Example: - - usb@f7ed0000 { - compatible = "chipidea,usb2"; - reg = <0xf7ed0000 0x10000>; - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&chip CLKID_USB0>; - phys = <&usb_phy0>; - phy-names = "usb-phy"; - vbus-supply = <®_usb0_vbus>; - itc-setting = <0x4>; /* 4 micro-frames */ - /* Incremental burst of unspecified length */ - ahb-burst-config = <0x0>; - tx-burst-size-dword = <0x10>; /* 64 bytes */ - rx-burst-size-dword = <0x10>; - extcon = <0>, <&usb_id>; - phy-clkgate-delay-us = <400>; - mux-controls = <&usb_switch>; - mux-control-names = "usb_switch"; - }; - -Example for HSIC: - - usb@2184400 { - compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; - reg = <0x02184400 0x200>; - interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clks IMX6QDL_CLK_USBOH3>; - fsl,usbphy = <&usbphynop1>; - fsl,usbmisc = <&usbmisc 2>; - phy_type = "hsic"; - dr_mode = "host"; - ahb-burst-config = <0x0>; - tx-burst-size-dword = <0x10>; - rx-burst-size-dword = <0x10>; - pinctrl-names = "idle", "active"; - pinctrl-0 = <&pinctrl_usbh2_idle>; - pinctrl-1 = <&pinctrl_usbh2_active>; - #address-cells = <1>; - #size-cells = <0>; - - usbnet: smsc@1 { - compatible = "usb424,9730"; - reg = <1>; - }; - }; |