diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 36 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/dwc3.txt | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt | 8 |
3 files changed, 45 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 529e51879fb2..adae82385dd6 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -80,15 +80,19 @@ Optional properties: controller. It's expected that a mux state of 0 indicates device mode and a mux state of 1 indicates host mode. - mux-control-names: Shall be "usb_switch" if mux-controls is specified. -- pinctrl-names: Names for optional pin modes in "default", "host", "device" +- pinctrl-names: Names for optional pin modes in "default", "host", "device". + In case of HSIC-mode, "idle" and "active" pin modes are mandatory. In this + case, the "idle" state needs to pull down the data and strobe pin + and the "active" state needs to pull up the strobe pin. - pinctrl-n: alternate pin modes i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one argument that indicate usb controller index - disable-over-current: disable over current detect -- over-current-active-high: over current signal polarity is high active, - typically over current signal polarity is low active. +- over-current-active-low: over current signal polarity is active low. +- over-current-active-high: over current signal polarity is active high. + It's recommended to specify the over current polarity. - external-vbus-divider: enables off-chip resistor divider for Vbus Example: @@ -111,3 +115,29 @@ Example: mux-controls = <&usb_switch>; mux-control-names = "usb_switch"; }; + +Example for HSIC: + + usb@2184400 { + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + reg = <0x02184400 0x200>; + interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_USBOH3>; + fsl,usbphy = <&usbphynop1>; + fsl,usbmisc = <&usbmisc 2>; + phy_type = "hsic"; + dr_mode = "host"; + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; + rx-burst-size-dword = <0x10>; + pinctrl-names = "idle", "active"; + pinctrl-0 = <&pinctrl_usbh2_idle>; + pinctrl-1 = <&pinctrl_usbh2_active>; + #address-cells = <1>; + #size-cells = <0>; + + usbnet: smsc@1 { + compatible = "usb424,9730"; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 636630fb92d7..8e5265e9f658 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -37,7 +37,11 @@ Optional properties: - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" or "usb3-phy". - resets: a single pair of phandle and reset specifier + - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable + - snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command + failure SW work-around for DWC_usb31 version 1.70a-ea06 + and prior. - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt index 3eee9e505400..4156c3e181c5 100644 --- a/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt @@ -59,6 +59,14 @@ For Tegra210: - avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. - dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. +- power-domains: A list of PM domain specifiers that reference each power-domain + used by the xHCI controller. This list must comprise of a specifier for the + XUSBA and XUSBC power-domains. See ../power/power_domain.txt and + ../arm/tegra/nvidia,tegra20-pmc.txt for details. +- power-domain-names: A list of names that represent each of the specifiers in + the 'power-domains' property. Must include 'xusb_ss' and 'xusb_host' which + represent the power-domains XUSBA and XUSBC, respectively. See + ../power/power_domain.txt for details. Optional properties: -------------------- |