diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 44 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt new file mode 100644 index 000000000000..633e21ce4b17 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt @@ -0,0 +1,35 @@ +Amlogic meson GPIO interrupt controller + +Meson SoCs contains an interrupt controller which is able to watch the SoC +pads and generate an interrupt on edge or level. The controller is essentially +a 256 pads to 8 GIC interrupt multiplexer, with a filter block to select edge +or level and polarity. It does not expose all 256 mux inputs because the +documentation shows that the upper part is not mapped to any pad. The actual +number of interrupt exposed depends on the SoC. + +Required properties: + +- compatible : must have "amlogic,meson8-gpio-intc” and either + “amlogic,meson8b-gpio-intc” for meson8b SoCs (S805) or + “amlogic,meson-gxbb-gpio-intc” for GXBB SoCs (S905) or + “amlogic,meson-gxl-gpio-intc” for GXL SoCs (S905X, S912) +- interrupt-parent : a phandle to the GIC the interrupts are routed to. + Usually this is provided at the root level of the device tree as it is + common to most of the SoC. +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value must be 2. +- meson,channel-interrupts: Array with the 8 upstream hwirq numbers. These + are the hwirqs used on the parent interrupt controller. + +Example: + +gpio_interrupt: interrupt-controller@9880 { + compatible = "amlogic,meson-gxbb-gpio-intc", + "amlogic,meson-gpio-intc"; + reg = <0x0 0x9880 0x0 0x10>; + interrupt-controller; + #interrupt-cells = <2>; + meson,channel-interrupts = <64 65 66 67 68 69 70 71>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index 4c29cdab0ea5..c3e6092f3add 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -75,6 +75,10 @@ These nodes must have the following properties: - reg: Specifies the base physical address and size of the ITS registers. +Optional: +- socionext,synquacer-pre-its: (u32, u32) tuple describing the untranslated + address and size of the pre-ITS window. + The main GIC node must contain the appropriate #address-cells, #size-cells and ranges properties for the reg property of all ITS nodes. diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt index 448273a30a11..36df06c5c567 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt @@ -2,7 +2,8 @@ Broadcom Generic Level 2 Interrupt Controller Required properties: -- compatible: should be "brcm,l2-intc" +- compatible: should be "brcm,l2-intc" for latched interrupt controllers + should be "brcm,bcm7271-l2-intc" for level interrupt controllers - reg: specifies the base physical address and size of the registers - interrupt-controller: identifies the node as an interrupt controller - #interrupt-cells: specifies the number of cells needed to encode an diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index e3f052d8c11a..33c9a10fdc91 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -13,6 +13,9 @@ Required properties: - "renesas,irqc-r8a7793" (R-Car M2-N) - "renesas,irqc-r8a7794" (R-Car E2) - "renesas,intc-ex-r8a7795" (R-Car H3) + - "renesas,intc-ex-r8a7796" (R-Car M3-W) + - "renesas,intc-ex-r8a77970" (R-Car V3M) + - "renesas,intc-ex-r8a77995" (R-Car D3) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory - clocks: Must contain a reference to the functional clock. |