diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
52 files changed, 2142 insertions, 389 deletions
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-actmon.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-actmon.txt deleted file mode 100644 index 897eedfa2bc8..000000000000 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-actmon.txt +++ /dev/null @@ -1,57 +0,0 @@ -NVIDIA Tegra Activity Monitor - -The activity monitor block collects statistics about the behaviour of other -components in the system. This information can be used to derive the rate at -which the external memory needs to be clocked in order to serve all requests -from the monitored clients. - -Required properties: -- compatible: should be "nvidia,tegra<chip>-actmon" -- reg: offset and length of the register set for the device -- interrupts: standard interrupt property -- clocks: Must contain a phandle and clock specifier pair for each entry in -clock-names. See ../../clock/clock-bindings.txt for details. -- clock-names: Must include the following entries: - - actmon - - emc -- resets: Must contain an entry for each entry in reset-names. See -../../reset/reset.txt for details. -- reset-names: Must include the following entries: - - actmon -- operating-points-v2: See ../bindings/opp/opp.txt for details. -- interconnects: Should contain entries for memory clients sitting on - MC->EMC memory interconnect path. -- interconnect-names: Should include name of the interconnect path for each - interconnect entry. Consult TRM documentation for - information about available memory clients, see MEMORY - CONTROLLER section. - -For each opp entry in 'operating-points-v2' table: -- opp-supported-hw: bitfield indicating SoC speedo ID mask -- opp-peak-kBps: peak bandwidth of the memory channel - -Example: - dfs_opp_table: opp-table { - compatible = "operating-points-v2"; - - opp@12750000 { - opp-hz = /bits/ 64 <12750000>; - opp-supported-hw = <0x000F>; - opp-peak-kBps = <51000>; - }; - ... - }; - - actmon@6000c800 { - compatible = "nvidia,tegra124-actmon"; - reg = <0x0 0x6000c800 0x0 0x400>; - interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&tegra_car TEGRA124_CLK_ACTMON>, - <&tegra_car TEGRA124_CLK_EMC>; - clock-names = "actmon", "emc"; - resets = <&tegra_car 119>; - reset-names = "actmon"; - operating-points-v2 = <&dfs_opp_table>; - interconnects = <&mc TEGRA124_MC_MPCORER &emc>; - interconnect-names = "cpu"; - }; diff --git a/Documentation/devicetree/bindings/crypto/cortina,sl3516-crypto.yaml b/Documentation/devicetree/bindings/crypto/cortina,sl3516-crypto.yaml new file mode 100644 index 000000000000..b633b8d0e6f0 --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/cortina,sl3516-crypto.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/crypto/cortina,sl3516-crypto.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SL3516 cryptographic offloader driver + +maintainers: + - Corentin Labbe <clabbe@baylibre.com> + +properties: + compatible: + enum: + - cortina,sl3516-crypto + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/cortina,gemini-clock.h> + #include <dt-bindings/reset/cortina,gemini-reset.h> + + crypto@62000000 { + compatible = "cortina,sl3516-crypto"; + reg = <0x62000000 0x10000>; + interrupts = <7 IRQ_TYPE_EDGE_RISING>; + resets = <&syscon GEMINI_RESET_SECURITY>; + clocks = <&syscon GEMINI_CLK_GATE_SECURITY>; + }; diff --git a/Documentation/devicetree/bindings/crypto/intel,ixp4xx-crypto.yaml b/Documentation/devicetree/bindings/crypto/intel,ixp4xx-crypto.yaml new file mode 100644 index 000000000000..9c53c27bd20a --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/intel,ixp4xx-crypto.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2018 Linaro Ltd. +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/crypto/intel,ixp4xx-crypto.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Intel IXP4xx cryptographic engine + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + The Intel IXP4xx cryptographic engine makes use of the IXP4xx NPE + (Network Processing Engine). Since it is not a device on its own + it is defined as a subnode of the NPE, if crypto support is + available on the platform. + +properties: + compatible: + const: intel,ixp4xx-crypto + + intel,npe-handle: + $ref: '/schemas/types.yaml#/definitions/phandle-array' + maxItems: 1 + description: phandle to the NPE this crypto engine is using, the cell + describing the NPE instance to be used. + + queue-rx: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: phandle to the RX queue on the NPE, the cell describing + the queue instance to be used. + + queue-txready: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: phandle to the TX READY queue on the NPE, the cell describing + the queue instance to be used. + +required: + - compatible + - intel,npe-handle + - queue-rx + - queue-txready + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/devfreq/nvidia,tegra30-actmon.yaml b/Documentation/devicetree/bindings/devfreq/nvidia,tegra30-actmon.yaml new file mode 100644 index 000000000000..e3379d106728 --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/nvidia,tegra30-actmon.yaml @@ -0,0 +1,126 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/devfreq/nvidia,tegra30-actmon.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra30 Activity Monitor + +maintainers: + - Dmitry Osipenko <digetx@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +description: | + The activity monitor block collects statistics about the behaviour of other + components in the system. This information can be used to derive the rate at + which the external memory needs to be clocked in order to serve all requests + from the monitored clients. + +properties: + compatible: + enum: + - nvidia,tegra30-actmon + - nvidia,tegra114-actmon + - nvidia,tegra124-actmon + - nvidia,tegra210-actmon + + reg: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - const: actmon + - const: emc + + resets: + maxItems: 1 + + reset-names: + items: + - const: actmon + + interrupts: + maxItems: 1 + + interconnects: + minItems: 1 + maxItems: 12 + + interconnect-names: + minItems: 1 + maxItems: 12 + description: + Should include name of the interconnect path for each interconnect + entry. Consult TRM documentation for information about available + memory clients, see MEMORY CONTROLLER and ACTIVITY MONITOR sections. + + operating-points-v2: + description: + Should contain freqs and voltages and opp-supported-hw property, which + is a bitfield indicating SoC speedo ID mask. + + "#cooling-cells": + const: 2 + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - interrupts + - interconnects + - interconnect-names + - operating-points-v2 + - "#cooling-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/memory/tegra30-mc.h> + + mc: memory-controller@7000f000 { + compatible = "nvidia,tegra30-mc"; + reg = <0x7000f000 0x400>; + clocks = <&clk 32>; + clock-names = "mc"; + + interrupts = <0 77 4>; + + #iommu-cells = <1>; + #reset-cells = <1>; + #interconnect-cells = <1>; + }; + + emc: external-memory-controller@7000f400 { + compatible = "nvidia,tegra30-emc"; + reg = <0x7000f400 0x400>; + interrupts = <0 78 4>; + clocks = <&clk 57>; + + nvidia,memory-controller = <&mc>; + operating-points-v2 = <&dvfs_opp_table>; + power-domains = <&domain>; + + #interconnect-cells = <0>; + }; + + actmon@6000c800 { + compatible = "nvidia,tegra30-actmon"; + reg = <0x6000c800 0x400>; + interrupts = <0 45 4>; + clocks = <&clk 119>, <&clk 57>; + clock-names = "actmon", "emc"; + resets = <&rst 119>; + reset-names = "actmon"; + operating-points-v2 = <&dvfs_opp_table>; + interconnects = <&mc TEGRA30_MC_MPCORER &emc>; + interconnect-names = "cpu-read"; + #cooling-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/firmware/intel,ixp4xx-network-processing-engine.yaml b/Documentation/devicetree/bindings/firmware/intel,ixp4xx-network-processing-engine.yaml index 1bd2870c3a9c..c435c9f369a4 100644 --- a/Documentation/devicetree/bindings/firmware/intel,ixp4xx-network-processing-engine.yaml +++ b/Documentation/devicetree/bindings/firmware/intel,ixp4xx-network-processing-engine.yaml @@ -26,9 +26,16 @@ properties: reg: items: - - description: NPE0 register range - - description: NPE1 register range - - description: NPE2 register range + - description: NPE0 (NPE-A) register range + - description: NPE1 (NPE-B) register range + - description: NPE2 (NPE-C) register range + + crypto: + $ref: /schemas/crypto/intel,ixp4xx-crypto.yaml# + type: object + description: Optional node for the embedded crypto engine, the node + should be named with the instance number of the NPE engine used for + the crypto engine. required: - compatible @@ -38,8 +45,15 @@ additionalProperties: false examples: - | - npe@c8006000 { + npe: npe@c8006000 { compatible = "intel,ixp4xx-network-processing-engine"; reg = <0xc8006000 0x1000>, <0xc8007000 0x1000>, <0xc8008000 0x1000>; + + crypto { + compatible = "intel,ixp4xx-crypto"; + intel,npe-handle = <&npe 2>; + queue-rx = <&qmgr 30>; + queue-txready = <&qmgr 29>; + }; }; ... diff --git a/Documentation/devicetree/bindings/hwmon/lm75.yaml b/Documentation/devicetree/bindings/hwmon/lm75.yaml index 96eed5cc7841..72980d083c21 100644 --- a/Documentation/devicetree/bindings/hwmon/lm75.yaml +++ b/Documentation/devicetree/bindings/hwmon/lm75.yaml @@ -30,6 +30,7 @@ properties: - st,stds75 - st,stlm75 - microchip,tcn75 + - ti,tmp1075 - ti,tmp100 - ti,tmp101 - ti,tmp105 diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml index 1ecd1831cf02..c84f9fe7f254 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml @@ -145,6 +145,19 @@ properties: required: - affinity + clocks: + maxItems: 1 + + clock-names: + items: + - const: aclk + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + dependencies: mbi-ranges: [ msi-controller ] msi-controller: [ mbi-ranges ] diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.yaml b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.yaml index b67b8cbd33fc..abb22db3bb28 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.yaml +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.yaml @@ -29,6 +29,7 @@ properties: - renesas,intc-ex-r8a774c0 # RZ/G2E - renesas,intc-ex-r8a7795 # R-Car H3 - renesas,intc-ex-r8a7796 # R-Car M3-W + - renesas,intc-ex-r8a77961 # R-Car M3-W+ - renesas,intc-ex-r8a77965 # R-Car M3-N - renesas,intc-ex-r8a77970 # R-Car V3M - renesas,intc-ex-r8a77980 # R-Car V3H diff --git a/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml new file mode 100644 index 000000000000..4ff6fabfcb30 --- /dev/null +++ b/Documentation/devicetree/bindings/ipmi/aspeed,ast2400-kcs-bmc.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED BMC KCS Devices + +maintainers: + - Andrew Jeffery <andrew@aj.id.au> + +description: | + The Aspeed BMC SoCs typically use the Keyboard-Controller-Style (KCS) + interfaces on the LPC bus for in-band IPMI communication with their host. + +properties: + compatible: + oneOf: + - description: Channel ID derived from reg + items: + enum: + - aspeed,ast2400-kcs-bmc-v2 + - aspeed,ast2500-kcs-bmc-v2 + - aspeed,ast2600-kcs-bmc + + - description: Old-style with explicit channel ID, no reg + deprecated: true + items: + enum: + - aspeed,ast2400-kcs-bmc + - aspeed,ast2500-kcs-bmc + + interrupts: + maxItems: 1 + + reg: + # maxItems: 3 + items: + - description: IDR register + - description: ODR register + - description: STR register + + aspeed,lpc-io-reg: + $ref: '/schemas/types.yaml#/definitions/uint32-array' + minItems: 1 + maxItems: 2 + description: | + The host CPU LPC IO data and status addresses for the device. For most + channels the status address is derived from the data address, but the + status address may be optionally provided. + + aspeed,lpc-interrupts: + $ref: "/schemas/types.yaml#/definitions/uint32-array" + minItems: 2 + maxItems: 2 + description: | + A 2-cell property expressing the LPC SerIRQ number and the interrupt + level/sense encoding (specified in the standard fashion). + + Note that the generated interrupt is issued from the BMC to the host, and + thus the target interrupt controller is not captured by the BMC's + devicetree. + + kcs_chan: + deprecated: true + $ref: '/schemas/types.yaml#/definitions/uint32' + description: The LPC channel number in the controller + + kcs_addr: + deprecated: true + $ref: '/schemas/types.yaml#/definitions/uint32' + description: The host CPU IO map address + +required: + - compatible + - interrupts + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - aspeed,ast2400-kcs-bmc + - aspeed,ast2500-kcs-bmc + then: + required: + - kcs_chan + - kcs_addr + else: + required: + - reg + - aspeed,lpc-io-reg + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + kcs3: kcs@24 { + compatible = "aspeed,ast2600-kcs-bmc"; + reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>; + aspeed,lpc-io-reg = <0xca2>; + aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + interrupts = <8>; + }; diff --git a/Documentation/devicetree/bindings/ipmi/aspeed-kcs-bmc.txt b/Documentation/devicetree/bindings/ipmi/aspeed-kcs-bmc.txt deleted file mode 100644 index 193e71ca96b0..000000000000 --- a/Documentation/devicetree/bindings/ipmi/aspeed-kcs-bmc.txt +++ /dev/null @@ -1,33 +0,0 @@ -# Aspeed KCS (Keyboard Controller Style) IPMI interface - -The Aspeed SOCs (AST2400 and AST2500) are commonly used as BMCs -(Baseboard Management Controllers) and the KCS interface can be -used to perform in-band IPMI communication with their host. - -## v1 -Required properties: -- compatible : should be one of - "aspeed,ast2400-kcs-bmc" - "aspeed,ast2500-kcs-bmc" -- interrupts : interrupt generated by the controller -- kcs_chan : The LPC channel number in the controller -- kcs_addr : The host CPU IO map address - -## v2 -Required properties: -- compatible : should be one of - "aspeed,ast2400-kcs-bmc-v2" - "aspeed,ast2500-kcs-bmc-v2" -- reg : The address and size of the IDR, ODR and STR registers -- interrupts : interrupt generated by the controller -- aspeed,lpc-io-reg : The host CPU LPC IO address for the device - -Example: - - kcs3: kcs@24 { - compatible = "aspeed,ast2500-kcs-bmc-v2"; - reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>; - aspeed,lpc-reg = <0xca2>; - interrupts = <8>; - status = "okay"; - }; diff --git a/Documentation/devicetree/bindings/media/atmel,isc.yaml b/Documentation/devicetree/bindings/media/atmel,isc.yaml new file mode 100644 index 000000000000..3e4bb8892d94 --- /dev/null +++ b/Documentation/devicetree/bindings/media/atmel,isc.yaml @@ -0,0 +1,114 @@ +# SPDX-License-Identifier: GPL-2.0-only +# Copyright (C) 2016-2021 Microchip Technology, Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/atmel,isc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Atmel Image Sensor Controller (ISC) + +maintainers: + - Eugen Hristev <eugen.hristev@microchip.com> + +description: | + The Image Sensor Controller (ISC) device provides the video input capabilities for the + Atmel/Microchip AT91 SAMA family of devices. + + The ISC has a single parallel input that supports RAW Bayer, RGB or YUV video, + with both external synchronization and BT.656 synchronization for the latter. + +properties: + compatible: + const: atmel,sama5d2-isc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 3 + maxItems: 3 + + clock-names: + items: + - const: hclock + - const: iscck + - const: gck + + '#clock-cells': + const: 0 + + clock-output-names: + const: isc-mck + + port: + $ref: /schemas/graph.yaml#/properties/port + description: + Input port node, single endpoint describing the input pad. + + properties: + endpoint: + $ref: video-interfaces.yaml# + + properties: + remote-endpoint: true + + bus-width: + enum: [8, 9, 10, 11, 12] + default: 12 + + hsync-active: + enum: [0, 1] + default: 1 + + vsync-active: + enum: [0, 1] + default: 1 + + pclk-sample: + enum: [0, 1] + default: 1 + + required: + - remote-endpoint + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - '#clock-cells' + - clock-output-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + isc: isc@f0008000 { + compatible = "atmel,sama5d2-isc"; + reg = <0xf0008000 0x4000>; + interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>; + clocks = <&isc_clk>, <&iscck>, <&isc_gclk>; + clock-names = "hclock", "iscck", "gck"; + #clock-cells = <0>; + clock-output-names = "isc-mck"; + + port { + isc_0: endpoint { + remote-endpoint = <&ov7740_0>; + hsync-active = <1>; + vsync-active = <0>; + pclk-sample = <1>; + bus-width = <8>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt deleted file mode 100644 index bbe0e87c6188..000000000000 --- a/Documentation/devicetree/bindings/media/atmel-isc.txt +++ /dev/null @@ -1,65 +0,0 @@ -Atmel Image Sensor Controller (ISC) ----------------------------------------------- - -Required properties for ISC: -- compatible - Must be "atmel,sama5d2-isc". -- reg - Physical base address and length of the registers set for the device. -- interrupts - Should contain IRQ line for the ISC. -- clocks - List of clock specifiers, corresponding to entries in - the clock-names property; - Please refer to clock-bindings.txt. -- clock-names - Required elements: "hclock", "iscck", "gck". -- #clock-cells - Should be 0. -- clock-output-names - Should be "isc-mck". -- pinctrl-names, pinctrl-0 - Please refer to pinctrl-bindings.txt. - -ISC supports a single port node with parallel bus. It should contain one -'port' child node with child 'endpoint' node. Please refer to the bindings -defined in Documentation/devicetree/bindings/media/video-interfaces.txt. - -Example: -isc: isc@f0008000 { - compatible = "atmel,sama5d2-isc"; - reg = <0xf0008000 0x4000>; - interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>; - clocks = <&isc_clk>, <&iscck>, <&isc_gclk>; - clock-names = "hclock", "iscck", "gck"; - #clock-cells = <0>; - clock-output-names = "isc-mck"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>; - - port { - isc_0: endpoint { - remote-endpoint = <&ov7740_0>; - hsync-active = <1>; - vsync-active = <0>; - pclk-sample = <1>; - }; - }; -}; - -i2c1: i2c@fc028000 { - ov7740: camera@21 { - compatible = "ovti,ov7740"; - reg = <0x21>; - clocks = <&isc>; - clock-names = "xvclk"; - assigned-clocks = <&isc>; - assigned-clock-rates = <24000000>; - - port { - ov7740_0: endpoint { - remote-endpoint = <&isc_0>; - }; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml b/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml new file mode 100644 index 000000000000..f50e54a722eb --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/rda,rda5807.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/rda,rda5807.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Unisoc Communications RDA5807 FM radio receiver + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +properties: + compatible: + enum: + - rda,rda5807 + + reg: + description: I2C address. + maxItems: 1 + + power-supply: true + + rda,lnan: + description: Use LNAN input port. + type: boolean + + rda,lnap: + description: Use LNAP input port. + type: boolean + + rda,analog-out: + description: Enable analog audio output. + type: boolean + + rda,i2s-out: + description: Enable I2S digital audio output. + type: boolean + + rda,lna-microamp: + description: LNA working current, in micro-amperes. + default: 2500 + enum: [1800, 2100, 2500, 3000] + +required: + - compatible + - reg + - power-supply + +additionalProperties: false + +examples: + - | + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + radio@11 { + compatible = "rda,rda5807"; + reg = <0x11>; + + power-supply = <&ldo6>; + + rda,lnan; + rda,lnap; + rda,analog-out; + }; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt index 06db6837cefd..ad1321e5a22d 100644 --- a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -9,6 +9,7 @@ Required properties: "mediatek,mt8173-vcodec-enc" for mt8173 avc encoder. "mediatek,mt8183-vcodec-enc" for MT8183 encoder. "mediatek,mt8173-vcodec-dec" for MT8173 decoder. + "mediatek,mt8192-vcodec-enc" for MT8192 encoder. - reg : Physical base address of the video codec registers and length of memory mapped region. - interrupts : interrupt number to the cpu. @@ -22,6 +23,7 @@ Required properties: - iommus : should point to the respective IOMMU block with master port as argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.yaml for details. +- dma-ranges : describes the dma address range space that the codec hw access. One of the two following nodes: - mediatek,vpu : the node of the video processor unit, if using VPU. - mediatek,scp : the node of the SCP unit, if using SCP. diff --git a/Documentation/devicetree/bindings/media/microchip,sama5d4-vdec.yaml b/Documentation/devicetree/bindings/media/microchip,sama5d4-vdec.yaml new file mode 100644 index 000000000000..4b77103ca913 --- /dev/null +++ b/Documentation/devicetree/bindings/media/microchip,sama5d4-vdec.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) + +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/media/microchip,sama5d4-vdec.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Hantro G1 VPU codec implemented on Microchip SAMA5D4 SoCs + +maintainers: + - Emil Velikov <emil.velikov@collabora.com> + +description: + Hantro G1 video decode accelerator present on Microchip SAMA5D4 SoCs. + +properties: + compatible: + const: microchip,sama5d4-vdec + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/at91.h> + #include <dt-bindings/interrupt-controller/irq.h> + + vdec0: vdec@300000 { + compatible = "microchip,sama5d4-vdec"; + reg = <0x00300000 0x100000>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 4>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 19>; + }; diff --git a/Documentation/devicetree/bindings/media/microchip,xisc.yaml b/Documentation/devicetree/bindings/media/microchip,xisc.yaml new file mode 100644 index 000000000000..41afe2e5f133 --- /dev/null +++ b/Documentation/devicetree/bindings/media/microchip,xisc.yaml @@ -0,0 +1,129 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2021 Microchip Technology, Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/microchip,xisc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip eXtended Image Sensor Controller (XISC) + +maintainers: + - Eugen Hristev <eugen.hristev@microchip.com> + +description: | + The eXtended Image Sensor Controller (XISC) device provides the video input capabilities for the + Microchip AT91 SAM family of devices. + + The XISC has a single internal parallel input that supports RAW Bayer, RGB or YUV video. + The source can be either a demuxer from a CSI2 type of bus, or a simple direct bridge to a + parallel sensor. + + The XISC provides one clock output that is used to clock the demuxer/bridge. + +properties: + compatible: + const: microchip,sama7g5-isc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: hclock + + '#clock-cells': + const: 0 + + clock-output-names: + const: isc-mck + + microchip,mipi-mode: + type: boolean + description: + As the XISC is usually connected to a demux/bridge, the XISC receives + the same type of input, however, it should be aware of the type of + signals received. The mipi-mode enables different internal handling + of the data and clock lines. + + port: + $ref: /schemas/graph.yaml#/properties/port + description: + Input port node, single endpoint describing the input pad. + + properties: + endpoint: + $ref: video-interfaces.yaml# + + properties: + bus-type: + enum: [5, 6] + + remote-endpoint: true + + bus-width: + enum: [8, 9, 10, 11, 12] + default: 12 + + hsync-active: + enum: [0, 1] + default: 1 + + vsync-active: + enum: [0, 1] + default: 1 + + pclk-sample: + enum: [0, 1] + default: 1 + + required: + - remote-endpoint + - bus-type + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - '#clock-cells' + - clock-output-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/at91.h> + #include <dt-bindings/interrupt-controller/irq.h> + + xisc: xisc@e1408000 { + compatible = "microchip,sama7g5-isc"; + reg = <0xe1408000 0x2000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 56>; + clock-names = "hclock"; + #clock-cells = <0>; + clock-output-names = "isc-mck"; + + port { + xisc_in: endpoint { + bus-type = <5>; /* Parallel */ + remote-endpoint = <&csi2dc_out>; + hsync-active = <1>; + vsync-active = <1>; + bus-width = <12>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml index d8ed480482b9..7c09eec78ce5 100644 --- a/Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml +++ b/Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml @@ -4,15 +4,17 @@ $id: http://devicetree.org/schemas/media/nxp,imx7-mipi-csi2.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: NXP i.MX7 MIPI CSI-2 receiver +title: NXP i.MX7 and i.MX8 MIPI CSI-2 receiver maintainers: - Rui Miguel Silva <rmfrfs@gmail.com> + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> description: |- - The NXP i.MX7 SoC family includes a MIPI CSI-2 receiver IP core, documented - as "CSIS V3.3". The IP core seems to originate from Samsung, and may be - compatible with some of the Exynos4 ad S5P SoCs. + The NXP i.MX7 and i.MX8 families contain SoCs that include a MIPI CSI-2 + receiver IP core named CSIS. The IP core originates from Samsung, and may be + compatible with some of the Exynos4 and S5P SoCs. i.MX7 SoCs use CSIS version + 3.3, and i.MX8 SoCs use CSIS version 3.6.3. While the CSI-2 receiver is separate from the MIPI D-PHY IP core, the PHY is completely wrapped by the CSIS and doesn't expose a control interface of its @@ -20,7 +22,9 @@ description: |- properties: compatible: - const: fsl,imx7-mipi-csi2 + enum: + - fsl,imx7-mipi-csi2 + - fsl,imx8mm-mipi-csi2 reg: maxItems: 1 @@ -29,16 +33,20 @@ properties: maxItems: 1 clocks: + minItems: 3 items: - description: The peripheral clock (a.k.a. APB clock) - description: The external clock (optionally used as the pixel clock) - description: The MIPI D-PHY clock + - description: The AXI clock clock-names: + minItems: 3 items: - const: pclk - const: wrap - const: phy + - const: axi power-domains: maxItems: 1 @@ -71,16 +79,30 @@ properties: properties: data-lanes: - oneOf: - - items: - - const: 1 - - items: - - const: 1 - - const: 2 + items: + minItems: 1 + maxItems: 4 + items: + - const: 1 + - const: 2 + - const: 3 + - const: 4 required: - data-lanes + allOf: + - if: + properties: + compatible: + contains: + const: fsl,imx7-mipi-csi2 + then: + properties: + data-lanes: + items: + maxItems: 2 + port@1: $ref: /schemas/graph.yaml#/properties/port description: @@ -93,12 +115,29 @@ required: - clocks - clock-names - power-domains - - phy-supply - - resets - ports additionalProperties: false +allOf: + - if: + properties: + compatible: + contains: + const: fsl,imx7-mipi-csi2 + then: + required: + - phy-supply + - resets + else: + properties: + clocks: + minItems: 4 + clock-names: + minItems: 4 + phy-supply: false + resets: false + examples: - | #include <dt-bindings/clock/imx7d-clock.h> @@ -106,7 +145,7 @@ examples: #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/reset/imx7-reset.h> - mipi_csi: mipi-csi@30750000 { + mipi-csi@30750000 { compatible = "fsl,imx7-mipi-csi2"; reg = <0x30750000 0x10000>; interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; @@ -144,4 +183,46 @@ examples: }; }; + - | + #include <dt-bindings/clock/imx8mm-clock.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mipi-csi@32e30000 { + compatible = "fsl,imx8mm-mipi-csi2"; + reg = <0x32e30000 0x1000>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <333000000>; + clocks = <&clk IMX8MM_CLK_DISP_APB_ROOT>, + <&clk IMX8MM_CLK_CSI1_ROOT>, + <&clk IMX8MM_CLK_CSI1_PHY_REF>, + <&clk IMX8MM_CLK_DISP_AXI_ROOT>; + clock-names = "pclk", "wrap", "phy", "axi"; + power-domains = <&mipi_pd>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + imx8mm_mipi_csi_in: endpoint { + remote-endpoint = <&imx477_out>; + data-lanes = <1 2 3 4>; + }; + }; + + port@1 { + reg = <1>; + + imx8mm_mipi_csi_out: endpoint { + remote-endpoint = <&csi_in>; + }; + }; + }; + }; + ... diff --git a/Documentation/devicetree/bindings/media/rc.yaml b/Documentation/devicetree/bindings/media/rc.yaml index af9e7e59e5a1..d4c541c4b164 100644 --- a/Documentation/devicetree/bindings/media/rc.yaml +++ b/Documentation/devicetree/bindings/media/rc.yaml @@ -45,6 +45,7 @@ properties: - rc-cec - rc-cinergy - rc-cinergy-1400 + - rc-ct-90405 - rc-d680-dmb - rc-delock-61959 - rc-dib0700-nec @@ -125,7 +126,6 @@ properties: - rc-snapstream-firefly - rc-streamzap - rc-su3000 - - rc-tango - rc-tanix-tx3mini - rc-tanix-tx5max - rc-tbs-nec diff --git a/Documentation/devicetree/bindings/media/renesas,csi2.yaml b/Documentation/devicetree/bindings/media/renesas,csi2.yaml index 20396f1be999..23703b767f5b 100644 --- a/Documentation/devicetree/bindings/media/renesas,csi2.yaml +++ b/Documentation/devicetree/bindings/media/renesas,csi2.yaml @@ -25,6 +25,7 @@ properties: - renesas,r8a774e1-csi2 # RZ/G2H - renesas,r8a7795-csi2 # R-Car H3 - renesas,r8a7796-csi2 # R-Car M3-W + - renesas,r8a77961-csi2 # R-Car M3-W+ - renesas,r8a77965-csi2 # R-Car M3-N - renesas,r8a77970-csi2 # R-Car V3M - renesas,r8a77980-csi2 # R-Car V3H diff --git a/Documentation/devicetree/bindings/media/renesas,isp.yaml b/Documentation/devicetree/bindings/media/renesas,isp.yaml new file mode 100644 index 000000000000..514857d36f6b --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,isp.yaml @@ -0,0 +1,196 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +# Copyright (C) 2021 Renesas Electronics Corp. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/renesas,isp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car ISP Channel Selector + +maintainers: + - Niklas Söderlund <niklas.soderlund@ragnatech.se> + +description: + The R-Car ISP Channel Selector provides MIPI CSI-2 VC and DT filtering + capabilities for the Renesas R-Car family of devices. It is used in + conjunction with the R-Car VIN and CSI-2 modules, which provides the video + capture capabilities. + +properties: + compatible: + items: + - enum: + - renesas,r8a779a0-isp # V3U + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + ports: + $ref: /schemas/graph.yaml#/properties/ports + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: + Input port node, multiple endpoints describing the connected R-Car + CSI-2 receivers. + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 0. + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 1. + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 2. + + port@4: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 3. + + port@5: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 4. + + port@6: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 5. + + port@7: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 6. + + port@8: + $ref: /schemas/graph.yaml#/properties/port + description: + Single endpoint describing the R-Car VIN connected to output port 7. + + required: + - port@0 + - port@1 + - port@2 + - port@3 + - port@4 + - port@5 + - port@6 + - port@7 + - port@8 + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + - resets + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a779a0-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a779a0-sysc.h> + + isp1: isp@fed20000 { + compatible = "renesas,r8a779a0-isp"; + reg = <0xfed20000 0x10000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 613>; + power-domains = <&sysc R8A779A0_PD_A3ISP01>; + resets = <&cpg 613>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + isp1csi41: endpoint@1 { + reg = <1>; + remote-endpoint = <&csi41isp1>; + }; + }; + + port@1 { + reg = <1>; + isp1vin08: endpoint { + remote-endpoint = <&vin08isp1>; + }; + }; + + port@2 { + reg = <2>; + isp1vin09: endpoint { + remote-endpoint = <&vin09isp1>; + }; + }; + + port@3 { + reg = <3>; + isp1vin10: endpoint { + remote-endpoint = <&vin10isp1>; + }; + }; + + port@4 { + reg = <4>; + isp1vin11: endpoint { + remote-endpoint = <&vin11isp1>; + }; + }; + + port@5 { + reg = <5>; + isp1vin12: endpoint { + remote-endpoint = <&vin12isp1>; + }; + }; + + port@6 { + reg = <6>; + isp1vin13: endpoint { + remote-endpoint = <&vin13isp1>; + }; + }; + + port@7 { + reg = <7>; + isp1vin14: endpoint { + remote-endpoint = <&vin14isp1>; + }; + }; + + port@8 { + reg = <8>; + isp1vin15: endpoint { + remote-endpoint = <&vin15isp1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,vin.yaml b/Documentation/devicetree/bindings/media/renesas,vin.yaml index dd1a5ce5896c..39bb6db2fb32 100644 --- a/Documentation/devicetree/bindings/media/renesas,vin.yaml +++ b/Documentation/devicetree/bindings/media/renesas,vin.yaml @@ -46,11 +46,13 @@ properties: - renesas,vin-r8a7779 # R-Car H1 - renesas,vin-r8a7795 # R-Car H3 - renesas,vin-r8a7796 # R-Car M3-W + - renesas,vin-r8a77961 # R-Car M3-W+ - renesas,vin-r8a77965 # R-Car M3-N - renesas,vin-r8a77970 # R-Car V3M - renesas,vin-r8a77980 # R-Car V3H - renesas,vin-r8a77990 # R-Car E3 - renesas,vin-r8a77995 # R-Car D3 + - renesas,vin-r8a779a0 # R-Car V3U reg: maxItems: 1 @@ -111,7 +113,7 @@ properties: description: VIN channel number $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 - maximum: 15 + maximum: 31 ports: $ref: /schemas/graph.yaml#/properties/ports @@ -187,6 +189,29 @@ properties: - required: - endpoint@3 + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: + Input port node, multiple endpoints describing all the R-Car ISP + modules connected the VIN. + + properties: + endpoint@0: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to ISP0. + + endpoint@1: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to ISP1. + + endpoint@2: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to ISP2. + + endpoint@3: + $ref: /schemas/graph.yaml#/properties/endpoint + description: Endpoint connected to ISP3. + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/media/rockchip,vdec.yaml b/Documentation/devicetree/bindings/media/rockchip,vdec.yaml index 8d35c327018b..089f11d21b25 100644 --- a/Documentation/devicetree/bindings/media/rockchip,vdec.yaml +++ b/Documentation/devicetree/bindings/media/rockchip,vdec.yaml @@ -15,7 +15,11 @@ description: |- properties: compatible: - const: rockchip,rk3399-vdec + oneOf: + - const: rockchip,rk3399-vdec + - items: + - const: rockchip,rk3228-vdec + - const: rockchip,rk3399-vdec reg: maxItems: 1 @@ -37,6 +41,10 @@ properties: - const: cabac - const: core + assigned-clocks: true + + assigned-clock-rates: true + power-domains: maxItems: 1 diff --git a/Documentation/devicetree/bindings/media/rockchip-vpu.yaml b/Documentation/devicetree/bindings/media/rockchip-vpu.yaml index c81dbc3e8960..b88172a59de7 100644 --- a/Documentation/devicetree/bindings/media/rockchip-vpu.yaml +++ b/Documentation/devicetree/bindings/media/rockchip-vpu.yaml @@ -15,10 +15,19 @@ description: properties: compatible: - enum: - - rockchip,rk3288-vpu - - rockchip,rk3328-vpu - - rockchip,rk3399-vpu + oneOf: + - enum: + - rockchip,rk3036-vpu + - rockchip,rk3066-vpu + - rockchip,rk3288-vpu + - rockchip,rk3328-vpu + - rockchip,rk3399-vpu + - items: + - const: rockchip,rk3188-vpu + - const: rockchip,rk3066-vpu + - items: + - const: rockchip,rk3228-vpu + - const: rockchip,rk3399-vpu reg: maxItems: 1 @@ -35,12 +44,20 @@ properties: - const: vdpu clocks: - maxItems: 2 + oneOf: + - maxItems: 2 + - maxItems: 4 clock-names: - items: - - const: aclk - - const: hclk + oneOf: + - items: + - const: aclk + - const: hclk + - items: + - const: aclk_vdpu + - const: hclk_vdpu + - const: aclk_vepu + - const: hclk_vepu power-domains: maxItems: 1 diff --git a/Documentation/devicetree/bindings/media/tango-ir.txt b/Documentation/devicetree/bindings/media/tango-ir.txt deleted file mode 100644 index a9f00c2bf897..000000000000 --- a/Documentation/devicetree/bindings/media/tango-ir.txt +++ /dev/null @@ -1,21 +0,0 @@ -Sigma Designs Tango IR NEC/RC-5/RC-6 decoder (SMP86xx and SMP87xx) - -Required properties: - -- compatible: "sigma,smp8642-ir" -- reg: address/size of NEC+RC5 area, address/size of RC6 area -- interrupts: spec for IR IRQ -- clocks: spec for IR clock (typically the crystal oscillator) - -Optional properties: - -- linux,rc-map-name: see Documentation/devicetree/bindings/media/rc.txt - -Example: - - ir@10518 { - compatible = "sigma,smp8642-ir"; - reg = <0x10518 0x18>, <0x105e0 0x1c>; - interrupts = <21 IRQ_TYPE_EDGE_RISING>; - clocks = <&xtal>; - }; diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt index 2661775a3825..99a84b69a29f 100644 --- a/Documentation/devicetree/bindings/mfd/mt6397.txt +++ b/Documentation/devicetree/bindings/mfd/mt6397.txt @@ -21,6 +21,7 @@ Required properties: compatible: "mediatek,mt6323" for PMIC MT6323 "mediatek,mt6358" for PMIC MT6358 + "mediatek,mt6359" for PMIC MT6359 "mediatek,mt6397" for PMIC MT6397 Optional subnodes: diff --git a/Documentation/devicetree/bindings/mmc/brcm,iproc-sdhci.yaml b/Documentation/devicetree/bindings/mmc/brcm,iproc-sdhci.yaml index 6f569fbfa134..2f63f2cdeb71 100644 --- a/Documentation/devicetree/bindings/mmc/brcm,iproc-sdhci.yaml +++ b/Documentation/devicetree/bindings/mmc/brcm,iproc-sdhci.yaml @@ -21,6 +21,7 @@ properties: - brcm,bcm2711-emmc2 - brcm,sdhci-iproc-cygnus - brcm,sdhci-iproc + - brcm,bcm7211a0-sdhci reg: minItems: 1 diff --git a/Documentation/devicetree/bindings/mmc/ingenic,mmc.yaml b/Documentation/devicetree/bindings/mmc/ingenic,mmc.yaml index 04ba8b7fc054..546480f41141 100644 --- a/Documentation/devicetree/bindings/mmc/ingenic,mmc.yaml +++ b/Documentation/devicetree/bindings/mmc/ingenic,mmc.yaml @@ -19,6 +19,7 @@ properties: - ingenic,jz4740-mmc - ingenic,jz4725b-mmc - ingenic,jz4760-mmc + - ingenic,jz4775-mmc - ingenic,jz4780-mmc - ingenic,x1000-mmc - items: diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml index e141330c1114..25ac8e200970 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml +++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml @@ -220,6 +220,11 @@ properties: description: eMMC HS400 enhanced strobe mode is supported + no-mmc-hs400: + $ref: /schemas/types.yaml#/definitions/flag + description: + All eMMC HS400 modes are not supported. + dsr: description: Value the card Driver Stage Register (DSR) should be programmed @@ -358,22 +363,6 @@ additionalProperties: true examples: - | - mmc@ab000000 { - compatible = "sdhci"; - reg = <0xab000000 0x200>; - interrupts = <23>; - bus-width = <4>; - cd-gpios = <&gpio 69 0>; - cd-inverted; - wp-gpios = <&gpio 70 0>; - max-frequency = <50000000>; - keep-power-in-suspend; - wakeup-source; - mmc-pwrseq = <&sdhci0_pwrseq>; - clk-phase-sd-hs = <63>, <72>; - }; - - - | mmc3: mmc@1c12000 { #address-cells = <1>; #size-cells = <0>; @@ -385,9 +374,9 @@ examples: non-removable; mmc-pwrseq = <&sdhci0_pwrseq>; - brcmf: bcrmf@1 { + brcmf: wifi@1 { reg = <1>; - compatible = "brcm,bcm43xx-fmac"; + compatible = "brcm,bcm4329-fmac"; interrupt-parent = <&pio>; interrupts = <10 8>; interrupt-names = "host-wake"; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt deleted file mode 100644 index 291532ac0446..000000000000 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ /dev/null @@ -1,53 +0,0 @@ -* Renesas Multi Media Card Interface (MMCIF) Controller - -This file documents differences between the core properties in mmc.txt -and the properties used by the MMCIF device. - - -Required properties: - -- compatible: should be "renesas,mmcif-<soctype>", "renesas,sh-mmcif" as a - fallback. Examples with <soctype> are: - - "renesas,mmcif-r7s72100" for the MMCIF found in r7s72100 SoCs - - "renesas,mmcif-r8a73a4" for the MMCIF found in r8a73a4 SoCs - - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs - - "renesas,mmcif-r8a7742" for the MMCIF found in r8a7742 SoCs - - "renesas,mmcif-r8a7743" for the MMCIF found in r8a7743 SoCs - - "renesas,mmcif-r8a7744" for the MMCIF found in r8a7744 SoCs - - "renesas,mmcif-r8a7745" for the MMCIF found in r8a7745 SoCs - - "renesas,mmcif-r8a7778" for the MMCIF found in r8a7778 SoCs - - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs - - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs - - "renesas,mmcif-r8a7793" for the MMCIF found in r8a7793 SoCs - - "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs - - "renesas,mmcif-sh73a0" for the MMCIF found in sh73a0 SoCs - -- interrupts: Some SoCs have only 1 shared interrupt, while others have either - 2 or 3 individual interrupts (error, int, card detect). Below is the number - of interrupts for each SoC: - 1: r8a73a4, r8a7742, r8a7743, r8a7744, r8a7745, r8a7778, r8a7790, r8a7791, - r8a7793, r8a7794 - 2: r8a7740, sh73a0 - 3: r7s72100 - -- clocks: reference to the functional clock - -- dmas: reference to the DMA channels, one per channel name listed in the - dma-names property. -- dma-names: must contain "tx" for the transmit DMA channel and "rx" for the - receive DMA channel. -- max-frequency: Maximum operating clock frequency, driver uses default clock - frequency if it is not set. - - -Example: R8A7790 (R-Car H2) MMCIF0 - - mmcif0: mmc@ee200000 { - compatible = "renesas,mmcif-r8a7790", "renesas,sh-mmcif"; - reg = <0 0xee200000 0 0x80>; - interrupts = <0 169 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp3_clks R8A7790_CLK_MMCIF0>; - dmas = <&dmac0 0xd1>, <&dmac0 0xd2>; - dma-names = "tx", "rx"; - max-frequency = <97500000>; - }; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.yaml b/Documentation/devicetree/bindings/mmc/renesas,mmcif.yaml new file mode 100644 index 000000000000..c36ba561c387 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.yaml @@ -0,0 +1,135 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/renesas,mmcif.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas Multi Media Card Interface (MMCIF) Controller + +maintainers: + - Wolfram Sang <wsa+renesas@sang-engineering.com> + +allOf: + - $ref: "mmc-controller.yaml" + +properties: + compatible: + items: + - enum: + - renesas,mmcif-r7s72100 # RZ/A1H + - renesas,mmcif-r8a73a4 # R-Mobile APE6 + - renesas,mmcif-r8a7740 # R-Mobile A1 + - renesas,mmcif-r8a7742 # RZ/G1H + - renesas,mmcif-r8a7743 # RZ/G1M + - renesas,mmcif-r8a7744 # RZ/G1N + - renesas,mmcif-r8a7745 # RZ/G1E + - renesas,mmcif-r8a7778 # R-Car M1A + - renesas,mmcif-r8a7790 # R-Car H2 + - renesas,mmcif-r8a7791 # R-Car M2-W + - renesas,mmcif-r8a7793 # R-Car M2-N + - renesas,mmcif-r8a7794 # R-Car E2 + - renesas,mmcif-sh73a0 # SH-Mobile AG5 + - const: renesas,sh-mmcif + + reg: + maxItems: 1 + + interrupts: true + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + minItems: 2 + maxItems: 4 + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + + max-frequency: true + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + +if: + properties: + compatible: + contains: + const: renesas,mmcif-r7s72100 +then: + properties: + interrupts: + items: + - description: Error interrupt + - description: Normal operation interrupt + - description: Card detection interrupt +else: + if: + properties: + compatible: + contains: + enum: + - renesas,mmcif-r8a7740 + - renesas,mmcif-sh73a0 + then: + properties: + interrupts: + items: + - description: Error interrupt + - description: Normal operation interrupt + else: + if: + properties: + compatible: + contains: + enum: + - renesas,mmcif-r8a73a4 + - renesas,mmcif-r8a7778 + then: + properties: + interrupts: + maxItems: 1 + else: + properties: + interrupts: + maxItems: 1 + required: + - resets + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7790-sysc.h> + + mmcif0: mmc@ee200000 { + compatible = "renesas,mmcif-r8a7790", "renesas,sh-mmcif"; + reg = <0xee200000 0x80>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 315>; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 315>; + dmas = <&dmac0 0xd1>, <&dmac0 0xd2>, <&dmac1 0xd1>, <&dmac1 0xd2>; + dma-names = "tx", "rx", "tx", "rx"; + max-frequency = <97500000>; + }; diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml index 3762f1c8de96..54fb59820d2b 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml @@ -29,21 +29,15 @@ properties: - const: rockchip,rk3288-dw-mshc - items: - enum: - # for Rockchip PX30 - rockchip,px30-dw-mshc - # for Rockchip RK3036 + - rockchip,rk1808-dw-mshc - rockchip,rk3036-dw-mshc - # for Rockchip RK322x - rockchip,rk3228-dw-mshc - # for Rockchip RK3308 - rockchip,rk3308-dw-mshc - # for Rockchip RK3328 - rockchip,rk3328-dw-mshc - # for Rockchip RK3368 - rockchip,rk3368-dw-mshc - # for Rockchip RK3399 - rockchip,rk3399-dw-mshc - # for Rockchip RV1108 + - rockchip,rk3568-dw-mshc - rockchip,rv1108-dw-mshc - const: rockchip,rk3288-dw-mshc diff --git a/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml b/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml index 3a79e39253d2..29399e88ac53 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml +++ b/Documentation/devicetree/bindings/mmc/sdhci-am654.yaml @@ -19,7 +19,6 @@ properties: - const: ti,am654-sdhci-5.1 - const: ti,j721e-sdhci-8bit - const: ti,j721e-sdhci-4bit - - const: ti,j721e-sdhci-4bit - const: ti,am64-sdhci-8bit - const: ti,am64-sdhci-4bit - items: diff --git a/Documentation/devicetree/bindings/regulator/max8893.yaml b/Documentation/devicetree/bindings/regulator/max8893.yaml new file mode 100644 index 000000000000..2b5e977bf409 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8893.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/max8893.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Regulator driver for MAX8893 PMIC from Maxim Integrated. + +maintainers: + - Sergey Larin <cerg2010cerg2010@mail.ru> + +description: | + The device has 5 LDO regulators and a single BUCK regulator. + Programming is done through I2C bus. + +properties: + compatible: + const: maxim,max8893 + + reg: + maxItems: 1 + + regulators: + type: object + + patternProperties: + "^(ldo[1-5]|buck)$": + $ref: "regulator.yaml#" + + additionalProperties: false + +additionalProperties: false + +required: + - compatible + - reg + - regulators + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@3e { + compatible = "maxim,max8893"; + reg = <0x3e>; + + regulators { + /* Front camera - s5k6aafx, back - m5mo */ + /* Numbers used to indicate the sequence */ + front_1_back_1: buck { + regulator-name = "cam_isp_core_1v2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + front_4_back_5: ldo1 { + regulator-name = "vt_io_1v8,cam_isp_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + front_3_back_4: ldo2 { + regulator-name = "vt_core_1v5"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + }; + + front_5_back_6: ldo3 { + regulator-name = "vt_cam_1v8,vt_sensor_io_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo4 { + /* not used */ + }; + + back_7: ldo5 { + regulator-name = "cam_sensor_io_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/regulator/mt6359-regulator.yaml b/Documentation/devicetree/bindings/regulator/mt6359-regulator.yaml new file mode 100644 index 000000000000..8cc413eb482d --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6359-regulator.yaml @@ -0,0 +1,385 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/mt6359-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MT6359 Regulator from MediaTek Integrated + +maintainers: + - Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com> + +description: | + List of regulators provided by this controller. It is named + according to its regulator type, buck_<name> and ldo_<name>. + MT6359 regulators node should be sub node of the MT6397 MFD node. + +patternProperties: + "^buck_v(s1|gpu11|modem|pu|core|s2|pa|proc2|proc1|core_sshub)$": + type: object + $ref: "regulator.yaml#" + + properties: + regulator-name: + pattern: "^v(s1|gpu11|modem|pu|core|s2|pa|proc2|proc1|core_sshub)$" + + unevaluatedProperties: false + + "^ldo_v(ibr|rf12|usb|camio|efuse|xo22)$": + type: object + $ref: "regulator.yaml#" + + properties: + regulator-name: + pattern: "^v(ibr|rf12|usb|camio|efuse|xo22)$" + + unevaluatedProperties: false + + "^ldo_v(rfck|emc|a12|a09|ufs|bbck)$": + type: object + $ref: "regulator.yaml#" + + properties: + regulator-name: + pattern: "^v(rfck|emc|a12|a09|ufs|bbck)$" + + unevaluatedProperties: false + + "^ldo_vcn(18|13|33_1_bt|13_1_wifi|33_2_bt|33_2_wifi)$": + type: object + $ref: "regulator.yaml#" + + properties: + regulator-name: + pattern: "^vcn(18|13|33_1_bt|13_1_wifi|33_2_bt|33_2_wifi)$" + + unevaluatedProperties: false + + "^ldo_vsram_(proc2|others|md|proc1|others_sshub)$": + type: object + $ref: "regulator.yaml#" + + properties: + regulator-name: + pattern: "^vsram_(proc2|others|md|proc1|others_sshub)$" + + unevaluatedProperties: false + + "^ldo_v(fe|bif|io)28$": + type: object + $ref: "regulator.yaml#" + + properties: + regulator-name: + pattern: "^v(fe|bif|io)28$" + + unevaluatedProperties: false + + "^ldo_v(aud|io|aux|rf|m)18$": + type: object + $ref: "regulator.yaml#" + + properties: + regulator-name: + pattern: "^v(aud|io|aux|rf|m)18$" + + unevaluatedProperties: false + + "^ldo_vsim[12]$": + type: object + $ref: "regulator.yaml#" + + properties: + regulator-name: + pattern: "^vsim[12]$" + + required: + - regulator-name + + unevaluatedProperties: false + +additionalProperties: false + +examples: + - | + pmic { + regulators { + mt6359_vs1_buck_reg: buck_vs1 { + regulator-name = "vs1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2200000>; + regulator-enable-ramp-delay = <0>; + regulator-always-on; + }; + mt6359_vgpu11_buck_reg: buck_vgpu11 { + regulator-name = "vgpu11"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1193750>; + regulator-ramp-delay = <5000>; + regulator-enable-ramp-delay = <200>; + regulator-allowed-modes = <0 1 2>; + }; + mt6359_vmodem_buck_reg: buck_vmodem { + regulator-name = "vmodem"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1100000>; + regulator-ramp-delay = <10760>; + regulator-enable-ramp-delay = <200>; + }; + mt6359_vpu_buck_reg: buck_vpu { + regulator-name = "vpu"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1193750>; + regulator-ramp-delay = <5000>; + regulator-enable-ramp-delay = <200>; + regulator-allowed-modes = <0 1 2>; + }; + mt6359_vcore_buck_reg: buck_vcore { + regulator-name = "vcore"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1300000>; + regulator-ramp-delay = <5000>; + regulator-enable-ramp-delay = <200>; + regulator-allowed-modes = <0 1 2>; + }; + mt6359_vs2_buck_reg: buck_vs2 { + regulator-name = "vs2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1600000>; + regulator-enable-ramp-delay = <0>; + regulator-always-on; + }; + mt6359_vpa_buck_reg: buck_vpa { + regulator-name = "vpa"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3650000>; + regulator-enable-ramp-delay = <300>; + }; + mt6359_vproc2_buck_reg: buck_vproc2 { + regulator-name = "vproc2"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1193750>; + regulator-ramp-delay = <7500>; + regulator-enable-ramp-delay = <200>; + regulator-allowed-modes = <0 1 2>; + }; + mt6359_vproc1_buck_reg: buck_vproc1 { + regulator-name = "vproc1"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1193750>; + regulator-ramp-delay = <7500>; + regulator-enable-ramp-delay = <200>; + regulator-allowed-modes = <0 1 2>; + }; + mt6359_vcore_sshub_buck_reg: buck_vcore_sshub { + regulator-name = "vcore_sshub"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1193750>; + }; + mt6359_vgpu11_sshub_buck_reg: buck_vgpu11_sshub { + regulator-name = "vgpu11_sshub"; + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1193750>; + }; + mt6359_vaud18_ldo_reg: ldo_vaud18 { + regulator-name = "vaud18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <240>; + }; + mt6359_vsim1_ldo_reg: ldo_vsim1 { + regulator-name = "vsim1"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <3100000>; + }; + mt6359_vibr_ldo_reg: ldo_vibr { + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + mt6359_vrf12_ldo_reg: ldo_vrf12 { + regulator-name = "vrf12"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + }; + mt6359_vusb_ldo_reg: ldo_vusb { + regulator-name = "vusb"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <960>; + regulator-always-on; + }; + mt6359_vsram_proc2_ldo_reg: ldo_vsram_proc2 { + regulator-name = "vsram_proc2"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <7500>; + regulator-enable-ramp-delay = <240>; + regulator-always-on; + }; + mt6359_vio18_ldo_reg: ldo_vio18 { + regulator-name = "vio18"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-enable-ramp-delay = <960>; + regulator-always-on; + }; + mt6359_vcamio_ldo_reg: ldo_vcamio { + regulator-name = "vcamio"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + }; + mt6359_vcn18_ldo_reg: ldo_vcn18 { + regulator-name = "vcn18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <240>; + }; + mt6359_vfe28_ldo_reg: ldo_vfe28 { + regulator-name = "vfe28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <120>; + }; + mt6359_vcn13_ldo_reg: ldo_vcn13 { + regulator-name = "vcn13"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1300000>; + }; + mt6359_vcn33_1_bt_ldo_reg: ldo_vcn33_1_bt { + regulator-name = "vcn33_1_bt"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3500000>; + }; + mt6359_vcn33_1_wifi_ldo_reg: ldo_vcn33_1_wifi { + regulator-name = "vcn33_1_wifi"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3500000>; + }; + mt6359_vaux18_ldo_reg: ldo_vaux18 { + regulator-name = "vaux18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <240>; + regulator-always-on; + }; + mt6359_vsram_others_ldo_reg: ldo_vsram_others { + regulator-name = "vsram_others"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <5000>; + regulator-enable-ramp-delay = <240>; + }; + mt6359_vefuse_ldo_reg: ldo_vefuse { + regulator-name = "vefuse"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + }; + mt6359_vxo22_ldo_reg: ldo_vxo22 { + regulator-name = "vxo22"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2200000>; + regulator-always-on; + }; + mt6359_vrfck_ldo_reg: ldo_vrfck { + regulator-name = "vrfck"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1700000>; + }; + mt6359_vrfck_1_ldo_reg: ldo_vrfck_1 { + regulator-name = "vrfck"; + regulator-min-microvolt = <1240000>; + regulator-max-microvolt = <1600000>; + }; + mt6359_vbif28_ldo_reg: ldo_vbif28 { + regulator-name = "vbif28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <240>; + }; + mt6359_vio28_ldo_reg: ldo_vio28 { + regulator-name = "vio28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + mt6359_vemc_ldo_reg: ldo_vemc { + regulator-name = "vemc"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <3300000>; + }; + mt6359_vemc_1_ldo_reg: ldo_vemc_1 { + regulator-name = "vemc"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + }; + mt6359_vcn33_2_bt_ldo_reg: ldo_vcn33_2_bt { + regulator-name = "vcn33_2_bt"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3500000>; + }; + mt6359_vcn33_2_wifi_ldo_reg: ldo_vcn33_2_wifi { + regulator-name = "vcn33_2_wifi"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3500000>; + }; + mt6359_va12_ldo_reg: ldo_va12 { + regulator-name = "va12"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + mt6359_va09_ldo_reg: ldo_va09 { + regulator-name = "va09"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1200000>; + }; + mt6359_vrf18_ldo_reg: ldo_vrf18 { + regulator-name = "vrf18"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1810000>; + }; + mt6359_vsram_md_ldo_reg: ldo_vsram_md { + regulator-name = "vsram_md"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <10760>; + regulator-enable-ramp-delay = <240>; + }; + mt6359_vufs_ldo_reg: ldo_vufs { + regulator-name = "vufs"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + }; + mt6359_vm18_ldo_reg: ldo_vm18 { + regulator-name = "vm18"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + }; + mt6359_vbbck_ldo_reg: ldo_vbbck { + regulator-name = "vbbck"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1200000>; + }; + mt6359_vsram_proc1_ldo_reg: ldo_vsram_proc1 { + regulator-name = "vsram_proc1"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + regulator-ramp-delay = <7500>; + regulator-enable-ramp-delay = <240>; + regulator-always-on; + }; + mt6359_vsim2_ldo_reg: ldo_vsim2 { + regulator-name = "vsim2"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <3100000>; + }; + mt6359_vsram_others_sshub_ldo: ldo_vsram_others_sshub { + regulator-name = "vsram_others_sshub"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1293750>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml index e561a5b941e4..34de38377aa6 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml +++ b/Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml @@ -33,6 +33,9 @@ description: | The names used for regulator nodes must match those supported by a given PMIC. Supported regulator node names are + For PM6150, smps1 - smps5, ldo1 - ldo19 + For PM6150L, smps1 - smps8, ldo1 - ldo11, bob + For PM7325, smps1 - smps8, ldo1 - ldo19 For PM8005, smps1 - smps4 For PM8009, smps1 - smps2, ldo1 - ldo7 For PM8150, smps1 - smps10, ldo1 - ldo18 @@ -41,15 +44,15 @@ description: | For PM8350C, smps1 - smps10, ldo1 - ldo13, bob For PM8998, smps1 - smps13, ldo1 - ldo28, lvs1 - lvs2 For PMI8998, bob - For PM6150, smps1 - smps5, ldo1 - ldo19 - For PM6150L, smps1 - smps8, ldo1 - ldo11, bob - For PMX55, smps1 - smps7, ldo1 - ldo16 - For PM7325, smps1 - smps8, ldo1 - ldo19 For PMR735A, smps1 - smps3, ldo1 - ldo7 + For PMX55, smps1 - smps7, ldo1 - ldo16 properties: compatible: enum: + - qcom,pm6150-rpmh-regulators + - qcom,pm6150l-rpmh-regulators + - qcom,pm7325-rpmh-regulators - qcom,pm8005-rpmh-regulators - qcom,pm8009-rpmh-regulators - qcom,pm8009-1-rpmh-regulators @@ -59,11 +62,9 @@ properties: - qcom,pm8350c-rpmh-regulators - qcom,pm8998-rpmh-regulators - qcom,pmi8998-rpmh-regulators - - qcom,pm6150-rpmh-regulators - - qcom,pm6150l-rpmh-regulators - - qcom,pmx55-rpmh-regulators - - qcom,pm7325-rpmh-regulators + - qcom,pmm8155au-rpmh-regulators - qcom,pmr735a-rpmh-regulators + - qcom,pmx55-rpmh-regulators qcom,pmic-id: description: | diff --git a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml index a35c6cb9bf97..83b53579f463 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml @@ -24,6 +24,10 @@ description: For mp5496, s2 + For pm8226, s1, s2, s3, s4, s5, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, + l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, + l26, l27, l28, lvs1 + For pm8841, s1, s2, s3, s4, s5, s6, s7, s8 For pm8916, s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, @@ -68,6 +72,7 @@ properties: compatible: enum: - qcom,rpm-mp5496-regulators + - qcom,rpm-pm8226-regulators - qcom,rpm-pm8841-regulators - qcom,rpm-pm8916-regulators - qcom,rpm-pm8941-regulators diff --git a/Documentation/devicetree/bindings/regulator/regulator.yaml b/Documentation/devicetree/bindings/regulator/regulator.yaml index 6d0bc9cd4040..a6ae9ecae5cc 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.yaml +++ b/Documentation/devicetree/bindings/regulator/regulator.yaml @@ -117,6 +117,88 @@ properties: description: Enable over current protection. type: boolean + regulator-oc-protection-microamp: + description: Set over current protection limit. This is a limit where + hardware performs emergency shutdown. Zero can be passed to disable + protection and value '1' indicates that protection should be enabled but + limit setting can be omitted. + + regulator-oc-error-microamp: + description: Set over current error limit. This is a limit where part of + the hardware propably is malfunctional and damage prevention is requested. + Zero can be passed to disable error detection and value '1' indicates + that detection should be enabled but limit setting can be omitted. + + regulator-oc-warn-microamp: + description: Set over current warning limit. This is a limit where hardware + is assumed still to be functional but approaching limit where it gets + damaged. Recovery actions should be initiated. Zero can be passed to + disable detection and value '1' indicates that detection should + be enabled but limit setting can be omitted. + + regulator-ov-protection-microvolt: + description: Set over voltage protection limit. This is a limit where + hardware performs emergency shutdown. Zero can be passed to disable + protection and value '1' indicates that protection should be enabled but + limit setting can be omitted. Limit is given as microvolt offset from + voltage set to regulator. + + regulator-ov-error-microvolt: + description: Set over voltage error limit. This is a limit where part of + the hardware propably is malfunctional and damage prevention is requested + Zero can be passed to disable error detection and value '1' indicates + that detection should be enabled but limit setting can be omitted. Limit + is given as microvolt offset from voltage set to regulator. + + regulator-ov-warn-microvolt: + description: Set over voltage warning limit. This is a limit where hardware + is assumed still to be functional but approaching limit where it gets + damaged. Recovery actions should be initiated. Zero can be passed to + disable detection and value '1' indicates that detection should + be enabled but limit setting can be omitted. Limit is given as microvolt + offset from voltage set to regulator. + + regulator-uv-protection-microvolt: + description: Set over under voltage protection limit. This is a limit where + hardware performs emergency shutdown. Zero can be passed to disable + protection and value '1' indicates that protection should be enabled but + limit setting can be omitted. Limit is given as microvolt offset from + voltage set to regulator. + + regulator-uv-error-microvolt: + description: Set under voltage error limit. This is a limit where part of + the hardware propably is malfunctional and damage prevention is requested + Zero can be passed to disable error detection and value '1' indicates + that detection should be enabled but limit setting can be omitted. Limit + is given as microvolt offset from voltage set to regulator. + + regulator-uv-warn-microvolt: + description: Set over under voltage warning limit. This is a limit where + hardware is assumed still to be functional but approaching limit where + it gets damaged. Recovery actions should be initiated. Zero can be passed + to disable detection and value '1' indicates that detection should + be enabled but limit setting can be omitted. Limit is given as microvolt + offset from voltage set to regulator. + + regulator-temp-protection-kelvin: + description: Set over temperature protection limit. This is a limit where + hardware performs emergency shutdown. Zero can be passed to disable + protection and value '1' indicates that protection should be enabled but + limit setting can be omitted. + + regulator-temp-error-kelvin: + description: Set over temperature error limit. This is a limit where part of + the hardware propably is malfunctional and damage prevention is requested + Zero can be passed to disable error detection and value '1' indicates + that detection should be enabled but limit setting can be omitted. + + regulator-temp-warn-kelvin: + description: Set over temperature warning limit. This is a limit where + hardware is assumed still to be functional but approaching limit where it + gets damaged. Recovery actions should be initiated. Zero can be passed to + disable detection and value '1' indicates that detection should + be enabled but limit setting can be omitted. + regulator-active-discharge: description: | tristate, enable/disable active discharge of regulators. The values are: diff --git a/Documentation/devicetree/bindings/regulator/richtek,rt6160-regulator.yaml b/Documentation/devicetree/bindings/regulator/richtek,rt6160-regulator.yaml new file mode 100644 index 000000000000..0534b0d68359 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/richtek,rt6160-regulator.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/richtek,rt6160-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Richtek RT6160 BuckBoost converter + +maintainers: + - ChiYuan Huang <cy_huang@richtek.com> + +description: | + The RT6160 is a high-efficiency buck-boost converter that can provide + up to 3A output current from 2025mV to 5200mV. And it support the wide + input voltage range from 2200mV to 5500mV. + + Datasheet is available at + https://www.richtek.com/assets/product_file/RT6160A/DS6160A-00.pdf + +allOf: + - $ref: regulator.yaml# + +properties: + compatible: + enum: + - richtek,rt6160 + + reg: + maxItems: 1 + + enable-gpios: + description: A connection of the 'enable' gpio line. + maxItems: 1 + + richtek,vsel-active-low: + description: | + Used to indicate the 'vsel' pin active level. if not specified, use + high active level as the default. + type: boolean + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + rt6160@75 { + compatible = "richtek,rt6160"; + reg = <0x75>; + enable-gpios = <&gpio26 2 0>; + regulator-name = "rt6160-buckboost"; + regulator-min-microvolt = <2025000>; + regulator-max-microvolt = <5200000>; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/richtek,rt6245-regulator.yaml b/Documentation/devicetree/bindings/regulator/richtek,rt6245-regulator.yaml new file mode 100644 index 000000000000..796ceac87445 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/richtek,rt6245-regulator.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/richtek,rt6245-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Richtek RT6245 High Current Voltage Regulator + +maintainers: + - ChiYuan Huang <cy_huang@richtek.com> + +description: | + The RT6245 is a high-performance, synchronous step-down converter + that can deliver up to 14A output current with an input supply + voltage range of 4.5V to 17V. + +allOf: + - $ref: regulator.yaml# + +properties: + compatible: + enum: + - richtek,rt6245 + + reg: + maxItems: 1 + + enable-gpios: + description: | + A connection of the chip 'enable' gpio line. If not provided, + it will be treat as a default-on power. + maxItems: 1 + + richtek,oc-level-select: + $ref: "/schemas/types.yaml#/definitions/uint8" + enum: [0, 1, 2, 3] + description: | + Over current level selection. Each respective value means the current + limit 8A, 14A, 12A, 10A. If this property is missing then keep in + in chip default. + + richtek,ot-level-select: + $ref: "/schemas/types.yaml#/definitions/uint8" + enum: [0, 1, 2] + description: | + Over temperature level selection. Each respective value means the degree + 150'c, 130'c, 170'c. If this property is missing then keep in chip + default. + + richtek,pgdly-time-select: + $ref: "/schemas/types.yaml#/definitions/uint8" + enum: [0, 1, 2, 3] + description: | + Power good signal delay time selection. Each respective value means the + delay time 0us, 10us, 20us, 40us. If this property is missing then keep + in chip default. + + + richtek,switch-freq-select: + $ref: "/schemas/types.yaml#/definitions/uint8" + enum: [0, 1, 2] + description: | + Buck switch frequency selection. Each respective value means 400KHz, + 800KHz, 1200KHz. If this property is missing then keep in chip default. + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + rt6245@34 { + compatible = "richtek,rt6245"; + status = "okay"; + reg = <0x34>; + enable-gpios = <&gpio26 2 0>; + + regulator-name = "rt6245-regulator"; + regulator-min-microvolt = <437500>; + regulator-max-microvolt = <1387500>; + regulator-boot-on; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml index b6515a0cee62..7cb74cc8c5d9 100644 --- a/Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml +++ b/Documentation/devicetree/bindings/regulator/rohm,bd9576-regulator.yaml @@ -27,6 +27,12 @@ patternProperties: Properties for single regulator. $ref: "regulator.yaml#" + properties: + rohm,ocw-fet-ron-micro-ohms: + description: | + External FET's ON-resistance. Required if VoutS1 OCP/OCW is + to be set. + required: - regulator-name diff --git a/Documentation/devicetree/bindings/spi/renesas,rzn1-spi.txt b/Documentation/devicetree/bindings/spi/renesas,rzn1-spi.txt deleted file mode 100644 index fb1a6728638d..000000000000 --- a/Documentation/devicetree/bindings/spi/renesas,rzn1-spi.txt +++ /dev/null @@ -1,11 +0,0 @@ -Renesas RZ/N1 SPI Controller - -This controller is based on the Synopsys DW Synchronous Serial Interface and -inherits all properties defined in snps,dw-apb-ssi.txt except for the -compatible property. - -Required properties: -- compatible : The device specific string followed by the generic RZ/N1 string. - Therefore it must be one of: - "renesas,r9a06g032-spi", "renesas,rzn1-spi" - "renesas,r9a06g033-spi", "renesas,rzn1-spi" diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml index 4825157cd92e..ca91201a9926 100644 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml @@ -67,6 +67,12 @@ properties: const: baikal,bt1-sys-ssi - description: Canaan Kendryte K210 SoS SPI Controller const: canaan,k210-spi + - description: Renesas RZ/N1 SPI Controller + items: + - enum: + - renesas,r9a06g032-spi # RZ/N1D + - renesas,r9a06g033-spi # RZ/N1S + - const: renesas,rzn1-spi # RZ/N1 reg: minItems: 1 diff --git a/Documentation/devicetree/bindings/spi/spi-cadence.txt b/Documentation/devicetree/bindings/spi/spi-cadence.txt deleted file mode 100644 index 05a2ef945664..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-cadence.txt +++ /dev/null @@ -1,30 +0,0 @@ -Cadence SPI controller Device Tree Bindings -------------------------------------------- - -Required properties: -- compatible : Should be "cdns,spi-r1p6" or "xlnx,zynq-spi-r1p6". -- reg : Physical base address and size of SPI registers map. -- interrupts : Property with a value describing the interrupt - number. -- clock-names : List of input clock names - "ref_clk", "pclk" - (See clock bindings for details). -- clocks : Clock phandles (see clock bindings for details). - -Optional properties: -- num-cs : Number of chip selects used. - If a decoder is used, this will be the number of - chip selects after the decoder. -- is-decoded-cs : Flag to indicate whether decoder is used or not. - -Example: - - spi@e0007000 { - compatible = "xlnx,zynq-spi-r1p6"; - clock-names = "ref_clk", "pclk"; - clocks = <&clkc 26>, <&clkc 35>; - interrupt-parent = <&intc>; - interrupts = <0 49 4>; - num-cs = <4>; - is-decoded-cs = <0>; - reg = <0xe0007000 0x1000>; - } ; diff --git a/Documentation/devicetree/bindings/spi/spi-cadence.yaml b/Documentation/devicetree/bindings/spi/spi-cadence.yaml new file mode 100644 index 000000000000..9787be21318e --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-cadence.yaml @@ -0,0 +1,66 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-cadence.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence SPI controller Device Tree Bindings + +maintainers: + - Michal Simek <michal.simek@xilinx.com> + +allOf: + - $ref: "spi-controller.yaml#" + +properties: + compatible: + enum: + - cdns,spi-r1p6 + - xlnx,zynq-spi-r1p6 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clock-names: + items: + - const: ref_clk + - const: pclk + + clocks: + maxItems: 2 + + num-cs: + description: | + Number of chip selects used. If a decoder is used, + this will be the number of chip selects after the + decoder. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 4 + default: 4 + + is-decoded-cs: + description: | + Flag to indicate whether decoder is used or not. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + default: 0 + +unevaluatedProperties: false + +examples: + - | + spi@e0007000 { + compatible = "xlnx,zynq-spi-r1p6"; + clock-names = "ref_clk", "pclk"; + clocks = <&clkc 26>, <&clkc 35>; + interrupt-parent = <&intc>; + interrupts = <0 49 4>; + num-cs = <4>; + is-decoded-cs = <0>; + reg = <0xe0007000 0x1000>; + }; +... diff --git a/Documentation/devicetree/bindings/spi/spi-controller.yaml b/Documentation/devicetree/bindings/spi/spi-controller.yaml index 0477396e4945..faef4f6f55b8 100644 --- a/Documentation/devicetree/bindings/spi/spi-controller.yaml +++ b/Documentation/devicetree/bindings/spi/spi-controller.yaml @@ -114,8 +114,11 @@ patternProperties: Compatible of the SPI device. reg: - minimum: 0 - maximum: 256 + minItems: 1 + maxItems: 256 + items: + minimum: 0 + maximum: 256 description: Chip select used by the device. diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.yaml b/Documentation/devicetree/bindings/spi/spi-rockchip.yaml index 1e6cf29e6388..7f987e79337c 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.yaml +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.yaml @@ -33,6 +33,7 @@ properties: - rockchip,rk3328-spi - rockchip,rk3368-spi - rockchip,rk3399-spi + - rockchip,rv1126-spi - const: rockchip,rk3066-spi reg: diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.txt b/Documentation/devicetree/bindings/spi/spi-xilinx.txt deleted file mode 100644 index 5f4ed3e5c994..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-xilinx.txt +++ /dev/null @@ -1,23 +0,0 @@ -Xilinx SPI controller Device Tree Bindings -------------------------------------------------- - -Required properties: -- compatible : Should be "xlnx,xps-spi-2.00.a", "xlnx,xps-spi-2.00.b" or "xlnx,axi-quad-spi-1.00.a" -- reg : Physical base address and size of SPI registers map. -- interrupts : Property with a value describing the interrupt - number. - -Optional properties: -- xlnx,num-ss-bits : Number of chip selects used. -- xlnx,num-transfer-bits : Number of bits per transfer. This will be 8 if not specified - -Example: - axi_quad_spi@41e00000 { - compatible = "xlnx,xps-spi-2.00.a"; - interrupt-parent = <&intc>; - interrupts = <0 31 1>; - reg = <0x41e00000 0x10000>; - xlnx,num-ss-bits = <0x1>; - xlnx,num-transfer-bits = <32>; - }; - diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.yaml b/Documentation/devicetree/bindings/spi/spi-xilinx.yaml new file mode 100644 index 000000000000..593f7693bace --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-xilinx.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-xilinx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx SPI controller Device Tree Bindings + +maintainers: + - Michal Simek <michal.simek@xilinx.com> + +allOf: + - $ref: "spi-controller.yaml#" + +properties: + compatible: + enum: + - xlnx,xps-spi-2.00.a + - xlnx,xps-spi-2.00.b + - xlnx,axi-quad-spi-1.00.a + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + xlnx,num-ss-bits: + description: Number of chip selects used. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 32 + + xlnx,num-transfer-bits: + description: Number of bits per transfer. This will be 8 if not specified. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [8, 16, 32] + default: 8 + +required: + - compatible + - reg + - interrupts + +unevaluatedProperties: false + +examples: + - | + spi0: spi@41e00000 { + compatible = "xlnx,xps-spi-2.00.a"; + interrupt-parent = <&intc>; + interrupts = <0 31 1>; + reg = <0x41e00000 0x10000>; + xlnx,num-ss-bits = <0x1>; + xlnx,num-transfer-bits = <32>; + }; +... diff --git a/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.txt b/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.txt deleted file mode 100644 index 0f6d37ff541c..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.txt +++ /dev/null @@ -1,25 +0,0 @@ -Xilinx Zynq UltraScale+ MPSoC GQSPI controller Device Tree Bindings -------------------------------------------------------------------- - -Required properties: -- compatible : Should be "xlnx,zynqmp-qspi-1.0". -- reg : Physical base address and size of GQSPI registers map. -- interrupts : Property with a value describing the interrupt - number. -- clock-names : List of input clock names - "ref_clk", "pclk" - (See clock bindings for details). -- clocks : Clock phandles (see clock bindings for details). - -Optional properties: -- num-cs : Number of chip selects used. - -Example: - qspi: spi@ff0f0000 { - compatible = "xlnx,zynqmp-qspi-1.0"; - clock-names = "ref_clk", "pclk"; - clocks = <&misc_clk &misc_clk>; - interrupts = <0 15 4>; - interrupt-parent = <&gic>; - num-cs = <1>; - reg = <0x0 0xff0f0000 0x1000>,<0x0 0xc0000000 0x8000000>; - }; diff --git a/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml b/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml new file mode 100644 index 000000000000..ea72c8001256 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-zynqmp-qspi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx Zynq UltraScale+ MPSoC GQSPI controller Device Tree Bindings + +maintainers: + - Michal Simek <michal.simek@xilinx.com> + +allOf: + - $ref: "spi-controller.yaml#" + +properties: + compatible: + const: xlnx,zynqmp-qspi-1.0 + + reg: + maxItems: 2 + + interrupts: + maxItems: 1 + + clock-names: + items: + - const: ref_clk + - const: pclk + + clocks: + maxItems: 2 + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/clock/xlnx-zynqmp-clk.h> + soc { + #address-cells = <2>; + #size-cells = <2>; + + qspi: spi@ff0f0000 { + compatible = "xlnx,zynqmp-qspi-1.0"; + clocks = <&zynqmp_clk QSPI_REF>, <&zynqmp_clk LPD_LSBUS>; + clock-names = "ref_clk", "pclk"; + interrupts = <0 15 4>; + interrupt-parent = <&gic>; + reg = <0x0 0xff0f0000 0x0 0x1000>, + <0x0 0xc0000000 0x0 0x8000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/submitting-patches.rst b/Documentation/devicetree/bindings/submitting-patches.rst index 104fa8fb2c17..8087780f1685 100644 --- a/Documentation/devicetree/bindings/submitting-patches.rst +++ b/Documentation/devicetree/bindings/submitting-patches.rst @@ -7,8 +7,8 @@ Submitting Devicetree (DT) binding patches I. For patch submitters ======================= - 0) Normal patch submission rules from Documentation/process/submitting-patches.rst - applies. + 0) Normal patch submission rules from + Documentation/process/submitting-patches.rst applies. 1) The Documentation/ and include/dt-bindings/ portion of the patch should be a separate patch. The preferred subject prefix for binding patches is:: @@ -25,8 +25,8 @@ I. For patch submitters make dt_binding_check - See Documentation/devicetree/bindings/writing-schema.rst for more details about - schema and tools setup. + See Documentation/devicetree/bindings/writing-schema.rst for more details + about schema and tools setup. 3) DT binding files should be dual licensed. The preferred license tag is (GPL-2.0-only OR BSD-2-Clause). @@ -84,7 +84,8 @@ II. For kernel maintainers III. Notes ========== - 0) Please see :doc:`ABI` for details regarding devicetree ABI. + 0) Please see Documentation/devicetree/bindings/ABI.rst for details + regarding devicetree ABI. 1) This document is intended as a general familiarization with the process as decided at the 2013 Kernel Summit. When in doubt, the current word of the diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml index 8341e9d23c1e..37ac0a3ae3b4 100644 --- a/Documentation/devicetree/bindings/trivial-devices.yaml +++ b/Documentation/devicetree/bindings/trivial-devices.yaml @@ -73,6 +73,8 @@ properties: - dallas,ds4510 # Digital Thermometer and Thermostat - dallas,ds75 + # Delta Electronics DPS920AB 920W 54V Power Supply + - delta,dps920ab # 1/4 Brick DC/DC Regulated Power Module - delta,q54sj108a2 # Devantech SRF02 ultrasonic ranger in I2C mode @@ -103,6 +105,8 @@ properties: - fsl,mpl3115 # MPR121: Proximity Capacitive Touch Sensor Controller - fsl,mpr121 + # Monolithic Power Systems Inc. multi-phase controller mp2888 + - mps,mp2888 # Monolithic Power Systems Inc. multi-phase controller mp2975 - mps,mp2975 # G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface |