diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
23 files changed, 1109 insertions, 62 deletions
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt index f16b99571af1..dd258674633c 100644 --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt @@ -11,6 +11,7 @@ Required properties: - compatible: should contain one of the following: * "brcm,bcm20702a1" + * "brcm,bcm4329-bt" * "brcm,bcm4330-bt" * "brcm,bcm43438-bt" * "brcm,bcm4345c5" @@ -22,7 +23,9 @@ Optional properties: - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt - shutdown-gpios: GPIO specifier, used to enable the BT module - device-wakeup-gpios: GPIO specifier, used to wakeup the controller - - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor + - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor. + deprecated, replaced by interrupts and + "host-wakeup" interrupt-names - clocks: 1 or 2 clocks as defined in clock-names below, in that order - clock-names: names for clock inputs, matching the clocks given - "extclk": deprecated, replaced by "txco" @@ -30,7 +33,14 @@ Optional properties: - "lpo": external low power 32.768 kHz clock - vbat-supply: phandle to regulator supply for VBAT - vddio-supply: phandle to regulator supply for VDDIO - + - brcm,bt-pcm-int-params: configure PCM parameters via a 5-byte array + - sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S + - pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps + - pcm-frame-type: short, long + - pcm-sync-mode: slave, master + - pcm-clock-mode: slave, master + - interrupts: must be one, used to wakeup the host processor + - interrupt-names: must be "host-wakeup" Example: @@ -41,5 +51,6 @@ Example: bluetooth { compatible = "brcm,bcm43438-bt"; max-speed = <921600>; + brcm,bt-pcm-int-params = [01 02 00 01 01]; }; }; diff --git a/Documentation/devicetree/bindings/net/dsa/ar9331.txt b/Documentation/devicetree/bindings/net/dsa/ar9331.txt new file mode 100644 index 000000000000..320607cbbb17 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/ar9331.txt @@ -0,0 +1,148 @@ +Atheros AR9331 built-in switch +============================= + +It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal +MDIO bus. All PHYs are built-in as well. + +Required properties: + + - compatible: should be: "qca,ar9331-switch" + - reg: Address on the MII bus for the switch. + - resets : Must contain an entry for each entry in reset-names. + - reset-names : Must include the following entries: "switch" + - interrupt-parent: Phandle to the parent interrupt controller + - interrupts: IRQ line for the switch + - interrupt-controller: Indicates the switch is itself an interrupt + controller. This is used for the PHY interrupts. + - #interrupt-cells: must be 1 + - mdio: Container of PHY and devices on the switches MDIO bus. + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional +required and optional properties. +Examples: + +eth0: ethernet@19000000 { + compatible = "qca,ar9330-eth"; + reg = <0x19000000 0x200>; + interrupts = <4>; + + resets = <&rst 9>, <&rst 22>; + reset-names = "mac", "mdio"; + clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>; + clock-names = "eth", "mdio"; + + phy-mode = "mii"; + phy-handle = <&phy_port4>; +}; + +eth1: ethernet@1a000000 { + compatible = "qca,ar9330-eth"; + reg = <0x1a000000 0x200>; + interrupts = <5>; + resets = <&rst 13>, <&rst 23>; + reset-names = "mac", "mdio"; + clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>; + clock-names = "eth", "mdio"; + + phy-mode = "gmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch10: switch@10 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "qca,ar9331-switch"; + reg = <0x10>; + resets = <&rst 8>; + reset-names = "switch"; + + interrupt-parent = <&miscintc>; + interrupts = <12>; + + interrupt-controller; + #interrupt-cells = <1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + switch_port0: port@0 { + reg = <0x0>; + label = "cpu"; + ethernet = <ð1>; + + phy-mode = "gmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + switch_port1: port@1 { + reg = <0x1>; + phy-handle = <&phy_port0>; + phy-mode = "internal"; + }; + + switch_port2: port@2 { + reg = <0x2>; + phy-handle = <&phy_port1>; + phy-mode = "internal"; + }; + + switch_port3: port@3 { + reg = <0x3>; + phy-handle = <&phy_port2>; + phy-mode = "internal"; + }; + + switch_port4: port@4 { + reg = <0x4>; + phy-handle = <&phy_port3>; + phy-mode = "internal"; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&switch10>; + + phy_port0: phy@0 { + reg = <0x0>; + interrupts = <0>; + }; + + phy_port1: phy@1 { + reg = <0x1>; + interrupts = <0>; + }; + + phy_port2: phy@2 { + reg = <0x2>; + interrupts = <0>; + }; + + phy_port3: phy@3 { + reg = <0x3>; + interrupts = <0>; + }; + + phy_port4: phy@4 { + reg = <0x4>; + interrupts = <0>; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt index 8a08621a5b54..afbcaebf062e 100644 --- a/Documentation/devicetree/bindings/net/mediatek-dwmac.txt +++ b/Documentation/devicetree/bindings/net/mediatek-dwmac.txt @@ -14,7 +14,7 @@ Required properties: Should be "macirq" for the main MAC IRQ - clocks: Must contain a phandle for each entry in clock-names. - clock-names: The name of the clock listed in the clocks property. These are - "axi", "apb", "mac_main", "ptp_ref" for MT2712 SoC + "axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712 SoC. - mac-address: See ethernet.txt in the same directory - phy-mode: See ethernet.txt in the same directory - mediatek,pericfg: A phandle to the syscon node that control ethernet @@ -23,8 +23,10 @@ Required properties: Optional properties: - mediatek,tx-delay-ps: TX clock delay macro value. Default is 0. It should be defined for RGMII/MII interface. + It should be defined for RMII interface when the reference clock is from MT2712 SoC. - mediatek,rx-delay-ps: RX clock delay macro value. Default is 0. - It should be defined for RGMII/MII/RMII interface. + It should be defined for RGMII/MII interface. + It should be defined for RMII interface. Both delay properties need to be a multiple of 170 for RGMII interface, or will round down. Range 0~31*170. Both delay properties need to be a multiple of 550 for MII/RMII interface, @@ -34,13 +36,20 @@ or will round down. Range 0~31*550. reference clock, which is from external PHYs, is connected to RXC pin on MT2712 SoC. Otherwise, is connected to TXC pin. +- mediatek,rmii-clk-from-mac: boolean property, if present indicates that + MT2712 SoC provides the RMII reference clock, which outputs to TXC pin only. - mediatek,txc-inverse: boolean property, if present indicates that 1. tx clock will be inversed in MII/RGMII case, 2. tx clock inside MAC will be inversed relative to reference clock which is from external PHYs in RMII case, and it rarely happen. + 3. the reference clock, which outputs to TXC pin will be inversed in RMII case + when the reference clock is from MT2712 SoC. - mediatek,rxc-inverse: boolean property, if present indicates that 1. rx clock will be inversed in MII/RGMII case. - 2. reference clock will be inversed when arrived at MAC in RMII case. + 2. reference clock will be inversed when arrived at MAC in RMII case, when + the reference clock is from external PHYs. + 3. the inside clock, which be sent to MAC, will be inversed in RMII case when + the reference clock is from MT2712 SoC. - assigned-clocks: mac_main and ptp_ref clocks - assigned-clock-parents: parent clocks of the assigned clocks @@ -50,29 +59,33 @@ Example: reg = <0 0x1101c000 0 0x1300>; interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>; interrupt-names = "macirq"; - phy-mode ="rgmii"; + phy-mode ="rgmii-rxid"; mac-address = [00 55 7b b5 7d f7]; clock-names = "axi", "apb", "mac_main", "ptp_ref", - "ptp_top"; + "rmii_internal"; clocks = <&pericfg CLK_PERI_GMAC>, <&pericfg CLK_PERI_GMAC_PCLK>, <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>, - <&topckgen CLK_TOP_ETHER_50M_SEL>; + <&topckgen CLK_TOP_ETHER_50M_SEL>, + <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>; assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>, - <&topckgen CLK_TOP_APLL1_D3>; + <&topckgen CLK_TOP_APLL1_D3>, + <&topckgen CLK_TOP_ETHERPLL_50M>; + power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>; mediatek,pericfg = <&pericfg>; mediatek,tx-delay-ps = <1530>; mediatek,rx-delay-ps = <1530>; mediatek,rmii-rxc; mediatek,txc-inverse; mediatek,rxc-inverse; - snps,txpbl = <32>; - snps,rxpbl = <32>; + snps,txpbl = <1>; + snps,rxpbl = <1>; snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>; snps,reset-active-low; }; diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 388ff48f53ae..44e2a4fab29e 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -8,8 +8,6 @@ Required properties: - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h for applicable values. Required only if interface type is PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID - - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h - for applicable values Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock delays will be left at their default values, as set by the PHY's pin strapping. @@ -42,6 +40,14 @@ Optional property: Some MACs work with differential SGMII clock. See data manual for details. + - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h + for applicable values (deprecated) + + -tx-fifo-depth - As defined in the ethernet-controller.yaml. Values for + the depth can be found in dt-bindings/net/ti-dp83867.h + -rx-fifo-depth - As defined in the ethernet-controller.yaml. Values for + the depth can be found in dt-bindings/net/ti-dp83867.h + Note: ti,min-output-impedance and ti,max-output-impedance are mutually exclusive. When both properties are present ti,max-output-impedance takes precedence. @@ -55,7 +61,7 @@ Example: reg = <0>; ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; - ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; }; Datasheet can be found: diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 017128394a3e..616c87746d6f 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -50,7 +50,7 @@ Optional properties: entry in clock-names. - clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref", "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and - "cxo_ref_clk_pin" for "qcom,wcn3990-wifi" + "cxo_ref_clk_pin" and optionally "qdss" for "qcom,wcn3990-wifi" compatible target. - qcom,msi_addr: MSI interrupt address. - qcom,msi_base: Base value to add before writing MSI data into @@ -88,6 +88,9 @@ Optional properties: of the host capability QMI request - qcom,xo-cal-data: xo cal offset to be configured in xo trim register. +- qcom,msa-fixed-perm: Boolean context flag to disable SCM call for statically + mapped msa region. + Example (to supply PCI based wifi block details): In this example, the node is defined as child node of the PCI controller. @@ -185,4 +188,5 @@ wifi@18000000 { vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; memory-region = <&wifi_msa_mem>; iommus = <&apps_smmu 0x0040 0x1>; + qcom,msa-fixed-perm; }; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml new file mode 100644 index 000000000000..a1717db36dba --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath11k.yaml @@ -0,0 +1,273 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2018-2019 The Linux Foundation. All rights reserved. + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/qcom,ath11k.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies ath11k wireless devices Generic Binding + +maintainers: + - Kalle Valo <kvalo@codeaurora.org> + +description: | + These are dt entries for Qualcomm Technologies, Inc. IEEE 802.11ax + devices, for example like AHB based IPQ8074. + +properties: + compatible: + const: qcom,ipq8074-wifi + + reg: + maxItems: 1 + + interrupts: + items: + - description: misc-pulse1 interrupt events + - description: misc-latch interrupt events + - description: sw exception interrupt events + - description: watchdog interrupt events + - description: interrupt event for ring CE0 + - description: interrupt event for ring CE1 + - description: interrupt event for ring CE2 + - description: interrupt event for ring CE3 + - description: interrupt event for ring CE4 + - description: interrupt event for ring CE5 + - description: interrupt event for ring CE6 + - description: interrupt event for ring CE7 + - description: interrupt event for ring CE8 + - description: interrupt event for ring CE9 + - description: interrupt event for ring CE10 + - description: interrupt event for ring CE11 + - description: interrupt event for ring host2wbm-desc-feed + - description: interrupt event for ring host2reo-re-injection + - description: interrupt event for ring host2reo-command + - description: interrupt event for ring host2rxdma-monitor-ring3 + - description: interrupt event for ring host2rxdma-monitor-ring2 + - description: interrupt event for ring host2rxdma-monitor-ring1 + - description: interrupt event for ring reo2ost-exception + - description: interrupt event for ring wbm2host-rx-release + - description: interrupt event for ring reo2host-status + - description: interrupt event for ring reo2host-destination-ring4 + - description: interrupt event for ring reo2host-destination-ring3 + - description: interrupt event for ring reo2host-destination-ring2 + - description: interrupt event for ring reo2host-destination-ring1 + - description: interrupt event for ring rxdma2host-monitor-destination-mac3 + - description: interrupt event for ring rxdma2host-monitor-destination-mac2 + - description: interrupt event for ring rxdma2host-monitor-destination-mac1 + - description: interrupt event for ring ppdu-end-interrupts-mac3 + - description: interrupt event for ring ppdu-end-interrupts-mac2 + - description: interrupt event for ring ppdu-end-interrupts-mac1 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac3 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac2 + - description: interrupt event for ring rxdma2host-monitor-status-ring-mac1 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac3 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac2 + - description: interrupt event for ring host2rxdma-host-buf-ring-mac1 + - description: interrupt event for ring rxdma2host-destination-ring-mac3 + - description: interrupt event for ring rxdma2host-destination-ring-mac2 + - description: interrupt event for ring rxdma2host-destination-ring-mac1 + - description: interrupt event for ring host2tcl-input-ring4 + - description: interrupt event for ring host2tcl-input-ring3 + - description: interrupt event for ring host2tcl-input-ring2 + - description: interrupt event for ring host2tcl-input-ring1 + - description: interrupt event for ring wbm2host-tx-completions-ring3 + - description: interrupt event for ring wbm2host-tx-completions-ring2 + - description: interrupt event for ring wbm2host-tx-completions-ring1 + - description: interrupt event for ring tcl2host-status-ring + + + interrupt-names: + items: + - const: misc-pulse1 + - const: misc-latch + - const: sw-exception + - const: watchdog + - const: ce0 + - const: ce1 + - const: ce2 + - const: ce3 + - const: ce4 + - const: ce5 + - const: ce6 + - const: ce7 + - const: ce8 + - const: ce9 + - const: ce10 + - const: ce11 + - const: host2wbm-desc-feed + - const: host2reo-re-injection + - const: host2reo-command + - const: host2rxdma-monitor-ring3 + - const: host2rxdma-monitor-ring2 + - const: host2rxdma-monitor-ring1 + - const: reo2ost-exception + - const: wbm2host-rx-release + - const: reo2host-status + - const: reo2host-destination-ring4 + - const: reo2host-destination-ring3 + - const: reo2host-destination-ring2 + - const: reo2host-destination-ring1 + - const: rxdma2host-monitor-destination-mac3 + - const: rxdma2host-monitor-destination-mac2 + - const: rxdma2host-monitor-destination-mac1 + - const: ppdu-end-interrupts-mac3 + - const: ppdu-end-interrupts-mac2 + - const: ppdu-end-interrupts-mac1 + - const: rxdma2host-monitor-status-ring-mac3 + - const: rxdma2host-monitor-status-ring-mac2 + - const: rxdma2host-monitor-status-ring-mac1 + - const: host2rxdma-host-buf-ring-mac3 + - const: host2rxdma-host-buf-ring-mac2 + - const: host2rxdma-host-buf-ring-mac1 + - const: rxdma2host-destination-ring-mac3 + - const: rxdma2host-destination-ring-mac2 + - const: rxdma2host-destination-ring-mac1 + - const: host2tcl-input-ring4 + - const: host2tcl-input-ring3 + - const: host2tcl-input-ring2 + - const: host2tcl-input-ring1 + - const: wbm2host-tx-completions-ring3 + - const: wbm2host-tx-completions-ring2 + - const: wbm2host-tx-completions-ring1 + - const: tcl2host-status-ring + + qcom,rproc: + $ref: /schemas/types.yaml#definitions/phandle + description: + DT entry of q6v5-wcss remoteproc driver. + Phandle to a node that can contain the following properties + * compatible + * reg + * reg-names + +required: + - compatible + - reg + - interrupts + - interrupt-names + - qcom,rproc + +additionalProperties: false + +examples: + - | + + q6v5_wcss: q6v5_wcss@CD00000 { + compatible = "qcom,ipq8074-wcss-pil"; + reg = <0xCD00000 0x4040>, + <0x4AB000 0x20>; + reg-names = "qdsp6", + "rmb"; + }; + + wifi0: wifi@c000000 { + compatible = "qcom,ipq8074-wifi"; + reg = <0xc000000 0x2000000>; + interrupts = <0 320 1>, + <0 319 1>, + <0 318 1>, + <0 317 1>, + <0 316 1>, + <0 315 1>, + <0 314 1>, + <0 311 1>, + <0 310 1>, + <0 411 1>, + <0 410 1>, + <0 40 1>, + <0 39 1>, + <0 302 1>, + <0 301 1>, + <0 37 1>, + <0 36 1>, + <0 296 1>, + <0 295 1>, + <0 294 1>, + <0 293 1>, + <0 292 1>, + <0 291 1>, + <0 290 1>, + <0 289 1>, + <0 288 1>, + <0 239 1>, + <0 236 1>, + <0 235 1>, + <0 234 1>, + <0 233 1>, + <0 232 1>, + <0 231 1>, + <0 230 1>, + <0 229 1>, + <0 228 1>, + <0 224 1>, + <0 223 1>, + <0 203 1>, + <0 183 1>, + <0 180 1>, + <0 179 1>, + <0 178 1>, + <0 177 1>, + <0 176 1>, + <0 163 1>, + <0 162 1>, + <0 160 1>, + <0 159 1>, + <0 158 1>, + <0 157 1>, + <0 156 1>; + interrupt-names = "misc-pulse1", + "misc-latch", + "sw-exception", + "watchdog", + "ce0", + "ce1", + "ce2", + "ce3", + "ce4", + "ce5", + "ce6", + "ce7", + "ce8", + "ce9", + "ce10", + "ce11", + "host2wbm-desc-feed", + "host2reo-re-injection", + "host2reo-command", + "host2rxdma-monitor-ring3", + "host2rxdma-monitor-ring2", + "host2rxdma-monitor-ring1", + "reo2ost-exception", + "wbm2host-rx-release", + "reo2host-status", + "reo2host-destination-ring4", + "reo2host-destination-ring3", + "reo2host-destination-ring2", + "reo2host-destination-ring1", + "rxdma2host-monitor-destination-mac3", + "rxdma2host-monitor-destination-mac2", + "rxdma2host-monitor-destination-mac1", + "ppdu-end-interrupts-mac3", + "ppdu-end-interrupts-mac2", + "ppdu-end-interrupts-mac1", + "rxdma2host-monitor-status-ring-mac3", + "rxdma2host-monitor-status-ring-mac2", + "rxdma2host-monitor-status-ring-mac1", + "host2rxdma-host-buf-ring-mac3", + "host2rxdma-host-buf-ring-mac2", + "host2rxdma-host-buf-ring-mac1", + "rxdma2host-destination-ring-mac3", + "rxdma2host-destination-ring-mac2", + "rxdma2host-destination-ring-mac1", + "host2tcl-input-ring4", + "host2tcl-input-ring3", + "host2tcl-input-ring2", + "host2tcl-input-ring1", + "wbm2host-tx-completions-ring3", + "wbm2host-tx-completions-ring2", + "wbm2host-tx-completions-ring1", + "tcl2host-status-ring"; + qcom,rproc = <&q6v5_wcss>; + }; diff --git a/Documentation/devicetree/bindings/ptp/ptp-ines.txt b/Documentation/devicetree/bindings/ptp/ptp-ines.txt new file mode 100644 index 000000000000..4c242bd1ce9c --- /dev/null +++ b/Documentation/devicetree/bindings/ptp/ptp-ines.txt @@ -0,0 +1,35 @@ +ZHAW InES PTP time stamping IP core + +The IP core needs two different kinds of nodes. The control node +lives somewhere in the memory map and specifies the address of the +control registers. There can be up to three port handles placed as +attributes of PHY nodes. These associate a particular MII bus with a +port index within the IP core. + +Required properties of the control node: + +- compatible: "ines,ptp-ctrl" +- reg: physical address and size of the register bank + +Required format of the port handle within the PHY node: + +- timestamper: provides control node reference and + the port channel within the IP core + +Example: + + tstamper: timestamper@60000000 { + compatible = "ines,ptp-ctrl"; + reg = <0x60000000 0x80>; + }; + + ethernet@80000000 { + ... + mdio { + ... + ethernet-phy@3 { + ... + timestamper = <&tstamper 0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/ptp/timestamper.txt b/Documentation/devicetree/bindings/ptp/timestamper.txt new file mode 100644 index 000000000000..fc550ce4d4ea --- /dev/null +++ b/Documentation/devicetree/bindings/ptp/timestamper.txt @@ -0,0 +1,42 @@ +Time stamps from MII bus snooping devices + +This binding supports non-PHY devices that snoop the MII bus and +provide time stamps. In contrast to PHY time stamping drivers (which +can simply attach their interface directly to the PHY instance), stand +alone MII time stamping drivers use this binding to specify the +connection between the snooping device and a given network interface. + +Non-PHY MII time stamping drivers typically talk to the control +interface over another bus like I2C, SPI, UART, or via a memory mapped +peripheral. This controller device is associated with one or more +time stamping channels, each of which snoops on a MII bus. + +The "timestamper" property lives in a phy node and links a time +stamping channel from the controller device to that phy's MII bus. + +Example: + + tstamper: timestamper@10000000 { + compatible = "ines,ptp-ctrl"; + reg = <0x10000000 0x80>; + }; + + ethernet@20000000 { + mdio { + ethernet-phy@1 { + timestamper = <&tstamper 0>; + }; + }; + }; + + ethernet@30000000 { + mdio { + ethernet-phy@2 { + timestamper = <&tstamper 1>; + }; + }; + }; + +In this example, time stamps from the MII bus attached to phy@1 will +appear on time stamp channel 0 (zero), and those from phy@2 appear on +channel 1. diff --git a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt index c223e54452da..802523196ee5 100644 --- a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt +++ b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt @@ -2,6 +2,7 @@ HWRNG support for the iproc-rng200 driver Required properties: - compatible : Must be one of: + "brcm,bcm2711-rng200" "brcm,bcm7211-rng200" "brcm,bcm7278-rng200" "brcm,iproc-rng200" diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt index 3080979350a0..fa4545ed81ca 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt @@ -17,6 +17,9 @@ Required properties: * "arb" : memory ARB line (required) * "rst" : dedicated device reset line (optional) - #sound-dai-cells: must be 0. +- amlogic,fifo-depth: The size of the controller's fifo in bytes. This + is useful for determining certain configuration such + as the flush threshold of the fifo Example of FRDDR A on the A113 SoC: @@ -27,4 +30,5 @@ frddr_a: audio-controller@1c0 { interrupts = <GIC_SPI 88 IRQ_TYPE_EDGE_RISING>; clocks = <&clkc_audio AUD_CLKID_FRDDR_A>; resets = <&arb AXG_ARB_FRDDR_A>; + fifo-depth = <512>; }; diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt index 1d4d9f938689..cb9a25165503 100644 --- a/Documentation/devicetree/bindings/sound/fsl,asrc.txt +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -8,7 +8,12 @@ three substreams within totally 10 channels. Required properties: - - compatible : Contains "fsl,imx35-asrc" or "fsl,imx53-asrc". + - compatible : Compatible list, should contain one of the following + compatibles: + "fsl,imx35-asrc", + "fsl,imx53-asrc", + "fsl,imx8qm-asrc", + "fsl,imx8qxp-asrc", - reg : Offset and length of the register set for the device. @@ -35,6 +40,11 @@ Required properties: - fsl,asrc-width : Defines a mutual sample width used by DPCM Back Ends. + - fsl,asrc-clk-map : Defines clock map used in driver. which is required + by imx8qm/imx8qxp platform + <0> - select the map for asrc0 in imx8qm/imx8qxp + <1> - select the map for asrc1 in imx8qm/imx8qxp + Optional properties: - big-endian : If this property is absent, the little endian mode diff --git a/Documentation/devicetree/bindings/sound/gtm601.txt b/Documentation/devicetree/bindings/sound/gtm601.txt index 5efc8c068de0..efa32a486c4a 100644 --- a/Documentation/devicetree/bindings/sound/gtm601.txt +++ b/Documentation/devicetree/bindings/sound/gtm601.txt @@ -1,10 +1,16 @@ GTM601 UMTS modem audio interface CODEC -This device has no configuration interface. Sample rate is fixed - 8kHz. +This device has no configuration interface. The sample rate and channels are +based on the compatible string + "option,gtm601" = 8kHz mono + "broadmobi,bm818" = 48KHz stereo Required properties: - - compatible : "option,gtm601" + - compatible : one of + "option,gtm601" + "broadmobi,bm818" + Example: diff --git a/Documentation/devicetree/bindings/sound/ingenic,codec.yaml b/Documentation/devicetree/bindings/sound/ingenic,codec.yaml new file mode 100644 index 000000000000..eb4be86464bb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ingenic,codec.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/ingenic,codec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ingenic JZ47xx internal codec DT bindings + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + +properties: + $nodename: + pattern: '^audio-codec@.*' + + compatible: + oneOf: + - const: ingenic,jz4770-codec + - const: ingenic,jz4725b-codec + - const: ingenic,jz4740-codec + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: aic + + '#sound-dai-cells': + const: 0 + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - '#sound-dai-cells' + +examples: + - | + #include <dt-bindings/clock/jz4740-cgu.h> + codec: audio-codec@10020080 { + compatible = "ingenic,jz4740-codec"; + reg = <0x10020080 0x8>; + #sound-dai-cells = <0>; + clocks = <&cgu JZ4740_CLK_AIC>; + clock-names = "aic"; + }; + +... diff --git a/Documentation/devicetree/bindings/sound/ingenic,jz4725b-codec.txt b/Documentation/devicetree/bindings/sound/ingenic,jz4725b-codec.txt deleted file mode 100644 index 05adc0d47b13..000000000000 --- a/Documentation/devicetree/bindings/sound/ingenic,jz4725b-codec.txt +++ /dev/null @@ -1,20 +0,0 @@ -Ingenic JZ4725B codec controller - -Required properties: -- compatible : "ingenic,jz4725b-codec" -- reg : codec registers location and length -- clocks : phandle to the AIC clock. -- clock-names: must be set to "aic". -- #sound-dai-cells: Must be set to 0. - -Example: - -codec: audio-codec@100200a4 { - compatible = "ingenic,jz4725b-codec"; - reg = <0x100200a4 0x8>; - - #sound-dai-cells = <0>; - - clocks = <&cgu JZ4725B_CLK_AIC>; - clock-names = "aic"; -}; diff --git a/Documentation/devicetree/bindings/sound/ingenic,jz4740-codec.txt b/Documentation/devicetree/bindings/sound/ingenic,jz4740-codec.txt deleted file mode 100644 index 1ffcade87e7b..000000000000 --- a/Documentation/devicetree/bindings/sound/ingenic,jz4740-codec.txt +++ /dev/null @@ -1,20 +0,0 @@ -Ingenic JZ4740 codec controller - -Required properties: -- compatible : "ingenic,jz4740-codec" -- reg : codec registers location and length -- clocks : phandle to the AIC clock. -- clock-names: must be set to "aic". -- #sound-dai-cells: Must be set to 0. - -Example: - -codec: audio-codec@10020080 { - compatible = "ingenic,jz4740-codec"; - reg = <0x10020080 0x8>; - - #sound-dai-cells = <0>; - - clocks = <&cgu JZ4740_CLK_AIC>; - clock-names = "aic"; -}; diff --git a/Documentation/devicetree/bindings/sound/qcom,sdm845.txt b/Documentation/devicetree/bindings/sound/qcom,sdm845.txt index 408c4837e6d5..ca8c89e88bfa 100644 --- a/Documentation/devicetree/bindings/sound/qcom,sdm845.txt +++ b/Documentation/devicetree/bindings/sound/qcom,sdm845.txt @@ -5,7 +5,10 @@ This binding describes the SDM845 sound card, which uses qdsp for audio. - compatible: Usage: required Value type: <stringlist> - Definition: must be "qcom,sdm845-sndcard" + Definition: must be one of this + "qcom,sdm845-sndcard" + "qcom,db845c-sndcard" + "lenovo,yoga-c630-sndcard" - audio-routing: Usage: Optional diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml new file mode 100644 index 000000000000..38eaf0c028f9 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml @@ -0,0 +1,175 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/qcom,wcd934x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bindings for Qualcomm WCD9340/WCD9341 Audio Codec + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + Qualcomm WCD9340/WCD9341 Codec is a standalone Hi-Fi audio codec IC. + It has in-built Soundwire controller, pin controller, interrupt mux and + supports both I2S/I2C and SLIMbus audio interfaces. + +properties: + compatible: + const: slim217,250 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + reset-gpios: + description: GPIO spec for reset line to use + maxItems: 1 + + slim-ifc-dev: true + + clocks: + maxItems: 1 + + clock-names: + const: extclk + + vdd-buck-supply: + description: A reference to the 1.8V buck supply + + vdd-buck-sido-supply: + description: A reference to the 1.8V SIDO buck supply + + vdd-rx-supply: + description: A reference to the 1.8V rx supply + + vdd-tx-supply: + description: A reference to the 1.8V tx supply + + vdd-vbat-supply: + description: A reference to the vbat supply + + vdd-io-supply: + description: A reference to the 1.8V I/O supply + + vdd-micbias-supply: + description: A reference to the micbias supply + + qcom,micbias1-microvolt: + description: micbias1 voltage + minimum: 1800000 + maximum: 2850000 + + qcom,micbias2-microvolt: + description: micbias2 voltage + minimum: 1800000 + maximum: 2850000 + + qcom,micbias3-microvolt: + description: micbias3 voltage + minimum: 1800000 + maximum: 2850000 + + qcom,micbias4-microvolt: + description: micbias4 voltage + minimum: 1800000 + maximum: 2850000 + + clock-output-names: + const: mclk + + clock-frequency: + description: Clock frequency of output clk in Hz + + interrupt-controller: true + + '#interrupt-cells': + const: 1 + + '#clock-cells': + const: 0 + + '#sound-dai-cells': + const: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + gpio@42: + type: object + allOf: + - $ref: ../gpio/qcom,wcd934x-gpio.yaml# + +patternProperties: + "^.*@[0-9a-f]+$": + type: object + description: | + WCD934x subnode for each slave devices. Bindings of each subnodes + depends on the specific driver providing the functionality and + documented in their respective bindings. + + properties: + reg: + maxItems: 1 + + required: + - reg + +required: + - compatible + - reg + - reset-gpios + - slim-ifc-dev + - interrupts + - interrupt-controller + - clock-frequency + - clock-output-names + - qcom,micbias1-microvolt + - qcom,micbias2-microvolt + - qcom,micbias3-microvolt + - qcom,micbias4-microvolt + - "#interrupt-cells" + - "#clock-cells" + - "#sound-dai-cells" + - "#address-cells" + - "#size-cells" + +examples: + - | + codec@1,0{ + compatible = "slim217,250"; + reg = <1 0>; + reset-gpios = <&tlmm 64 0>; + slim-ifc-dev = <&wcd9340_ifd>; + #sound-dai-cells = <1>; + interrupt-parent = <&tlmm>; + interrupts = <54 4>; + interrupt-controller; + #interrupt-cells = <1>; + #clock-cells = <0>; + clock-frequency = <9600000>; + clock-output-names = "mclk"; + qcom,micbias1-microvolt = <1800000>; + qcom,micbias2-microvolt = <1800000>; + qcom,micbias3-microvolt = <1800000>; + qcom,micbias4-microvolt = <1800000>; + clock-names = "extclk"; + clocks = <&rpmhcc 2>; + + #address-cells = <1>; + #size-cells = <1>; + + gpio@42 { + compatible = "qcom,wcd9340-gpio"; + reg = <0x42 0x2>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml new file mode 100644 index 000000000000..ea44d03e58ca --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,wsa881x.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/qcom,wsa881x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bindings for Qualcomm WSA8810/WSA8815 Class-D Smart Speaker Amplifier + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + WSA8810 is a class-D smart speaker amplifier and WSA8815 + is a high-output power class-D smart speaker amplifier. + Their primary operating mode uses a SoundWire digital audio + interface. This binding is for SoundWire interface. + +properties: + compatible: + const: sdw10217201000 + + reg: + maxItems: 1 + + powerdown-gpios: + description: GPIO spec for Powerdown/Shutdown line to use + maxItems: 1 + + '#thermal-sensor-cells': + const: 0 + + '#sound-dai-cells': + const: 0 + +required: + - compatible + - reg + - powerdown-gpios + - "#thermal-sensor-cells" + - "#sound-dai-cells" + +additionalProperties: false + +examples: + - | + soundwire@c2d0000 { + #address-cells = <2>; + #size-cells = <0>; + reg = <0x0c2d0000 0x2000>; + + speaker@0,1 { + compatible = "sdw10217201000"; + reg = <0 1>; + powerdown-gpios = <&wcdpinctrl 2 0>; + #thermal-sensor-cells = <0>; + #sound-dai-cells = <0>; + }; + + speaker@0,2 { + compatible = "sdw10217201000"; + reg = <0 2>; + powerdown-gpios = <&wcdpinctrl 2 0>; + #thermal-sensor-cells = <0>; + #sound-dai-cells = <0>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/sound/rt1015.txt b/Documentation/devicetree/bindings/sound/rt1015.txt new file mode 100644 index 000000000000..fcfd02d8d32f --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt1015.txt @@ -0,0 +1,17 @@ +RT1015 Mono Class D Audio Amplifier + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt1015". + +- reg : The I2C address of the device. + + +Example: + +rt1015: codec@28 { + compatible = "realtek,rt1015"; + reg = <0x28>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5645.txt b/Documentation/devicetree/bindings/sound/rt5645.txt index a03f9a872a71..41a62fd2ae1f 100644 --- a/Documentation/devicetree/bindings/sound/rt5645.txt +++ b/Documentation/devicetree/bindings/sound/rt5645.txt @@ -10,6 +10,10 @@ Required properties: - interrupts : The CODEC's interrupt output. +- avdd-supply: Power supply for AVDD, providing 1.8V. + +- cpvdd-supply: Power supply for CPVDD, providing 3.5V. + Optional properties: - hp-detect-gpios: diff --git a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml new file mode 100644 index 000000000000..87369264feb9 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml @@ -0,0 +1,160 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/allwinner,sun8i-a83t-ths.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner SUN8I Thermal Controller Device Tree Bindings + +maintainers: + - Vasily Khoruzhick <anarsoul@gmail.com> + - Yangtao Li <tiny.windzz@gmail.com> + +properties: + compatible: + enum: + - allwinner,sun8i-a83t-ths + - allwinner,sun8i-h3-ths + - allwinner,sun8i-r40-ths + - allwinner,sun50i-a64-ths + - allwinner,sun50i-h5-ths + - allwinner,sun50i-h6-ths + + clocks: + minItems: 1 + maxItems: 2 + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + minItems: 1 + maxItems: 2 + items: + - const: bus + - const: mod + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + resets: + maxItems: 1 + + nvmem-cells: + maxItems: 1 + description: Calibration data for thermal sensors + + nvmem-cell-names: + const: calibration + + # See ./thermal.txt for details + "#thermal-sensor-cells": + enum: + - 0 + - 1 + +allOf: + - if: + properties: + compatible: + contains: + const: allwinner,sun50i-h6-ths + + then: + properties: + clocks: + maxItems: 1 + + clock-names: + maxItems: 1 + + else: + properties: + clocks: + minItems: 2 + + clock-names: + minItems: 2 + + - if: + properties: + compatible: + contains: + const: allwinner,sun8i-h3-ths + + then: + properties: + "#thermal-sensor-cells": + const: 0 + + else: + properties: + "#thermal-sensor-cells": + const: 1 + + - if: + properties: + compatible: + contains: + enum: + - const: allwinner,sun8i-h3-ths + - const: allwinner,sun8i-r40-ths + - const: allwinner,sun50i-a64-ths + - const: allwinner,sun50i-h5-ths + - const: allwinner,sun50i-h6-ths + + then: + required: + - clocks + - clock-names + - resets + +required: + - compatible + - reg + - interrupts + - '#thermal-sensor-cells' + +additionalProperties: false + +examples: + - | + thermal-sensor@1f04000 { + compatible = "allwinner,sun8i-a83t-ths"; + reg = <0x01f04000 0x100>; + interrupts = <0 31 0>; + nvmem-cells = <&ths_calibration>; + nvmem-cell-names = "calibration"; + #thermal-sensor-cells = <1>; + }; + + - | + thermal-sensor@1c25000 { + compatible = "allwinner,sun8i-h3-ths"; + reg = <0x01c25000 0x400>; + clocks = <&ccu 0>, <&ccu 1>; + clock-names = "bus", "mod"; + resets = <&ccu 2>; + interrupts = <0 31 0>; + nvmem-cells = <&ths_calibration>; + nvmem-cell-names = "calibration"; + #thermal-sensor-cells = <0>; + }; + + - | + thermal-sensor@5070400 { + compatible = "allwinner,sun50i-h6-ths"; + reg = <0x05070400 0x100>; + clocks = <&ccu 0>; + clock-names = "bus"; + resets = <&ccu 2>; + interrupts = <0 15 0>; + nvmem-cells = <&ths_calibration>; + nvmem-cell-names = "calibration"; + #thermal-sensor-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml new file mode 100644 index 000000000000..d9fdf4809a49 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/brcm,avs-ro-thermal.yaml @@ -0,0 +1,48 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/brcm,avs-ro-thermal.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom AVS ring oscillator thermal + +maintainers: + - Stefan Wahren <wahrenst@gmx.net> + +description: |+ + The thermal node should be the child of a syscon node with the + required property: + + - compatible: Should be one of the following: + "brcm,bcm2711-avs-monitor", "syscon", "simple-mfd" + + Refer to the the bindings described in + Documentation/devicetree/bindings/mfd/syscon.txt + +properties: + compatible: + const: brcm,bcm2711-thermal + + # See ./thermal.txt for details + "#thermal-sensor-cells": + const: 0 + +required: + - compatible + - '#thermal-sensor-cells' + +additionalProperties: false + +examples: + - | + avs-monitor@7d5d2000 { + compatible = "brcm,bcm2711-avs-monitor", + "syscon", "simple-mfd"; + reg = <0x7d5d2000 0xf00>; + + thermal: thermal { + compatible = "brcm,bcm2711-thermal"; + #thermal-sensor-cells = <0>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/thermal/brcm,avs-tmon.txt b/Documentation/devicetree/bindings/thermal/brcm,avs-tmon.txt index 43a9ed545944..74a9ef09db8b 100644 --- a/Documentation/devicetree/bindings/thermal/brcm,avs-tmon.txt +++ b/Documentation/devicetree/bindings/thermal/brcm,avs-tmon.txt @@ -3,9 +3,13 @@ Thermal management core, provided by the AVS TMON hardware block. Required properties: -- compatible: must be "brcm,avs-tmon" and/or "brcm,avs-tmon-bcm7445" +- compatible: must be one of: + "brcm,avs-tmon-bcm7216" + "brcm,avs-tmon-bcm7445" + "brcm,avs-tmon" - reg: address range for the AVS TMON registers -- interrupts: temperature monitor interrupt, for high/low threshold triggers +- interrupts: temperature monitor interrupt, for high/low threshold triggers, + required except for "brcm,avs-tmon-bcm7216" - interrupt-names: should be "tmon" Example: |