diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
38 files changed, 1108 insertions, 138 deletions
diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt new file mode 100644 index 000000000000..1812c848e369 --- /dev/null +++ b/Documentation/devicetree/bindings/eeprom/at24.txt @@ -0,0 +1,78 @@ +EEPROMs (I2C) + +Required properties: + + - compatible: Must be a "<manufacturer>,<model>" pair. The following <model> + values are supported (assuming "atmel" as manufacturer): + + "atmel,24c00", + "atmel,24c01", + "atmel,24cs01", + "atmel,24c02", + "atmel,24cs02", + "atmel,24mac402", + "atmel,24mac602", + "atmel,spd", + "atmel,24c04", + "atmel,24cs04", + "atmel,24c08", + "atmel,24cs08", + "atmel,24c16", + "atmel,24cs16", + "atmel,24c32", + "atmel,24cs32", + "atmel,24c64", + "atmel,24cs64", + "atmel,24c128", + "atmel,24c256", + "atmel,24c512", + "atmel,24c1024", + + If <manufacturer> is not "atmel", then a fallback must be used + with the same <model> and "atmel" as manufacturer. + + Example: + compatible = "microchip,24c128", "atmel,24c128"; + + Supported manufacturers are: + + "catalyst", + "microchip", + "ramtron", + "renesas", + "nxp", + "st", + + Some vendors use different model names for chips which are just + variants of the above. Known such exceptions are listed below: + + "renesas,r1ex24002" - the fallback is "atmel,24c02" + + - reg: The I2C address of the EEPROM. + +Optional properties: + + - pagesize: The length of the pagesize for writing. Please consult the + manual of your device, that value varies a lot. A wrong value + may result in data loss! If not specified, a safety value of + '1' is used which will be very slow. + + - read-only: This parameterless property disables writes to the eeprom. + + - size: Total eeprom size in bytes. + + - no-read-rollover: This parameterless property indicates that the + multi-address eeprom does not automatically roll over + reads to the next slave address. Please consult the + manual of your device. + + - wp-gpios: GPIO to which the write-protect pin of the chip is connected. + +Example: + +eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + pagesize = <32>; + wp-gpios = <&gpio1 3 0>; +}; diff --git a/Documentation/devicetree/bindings/eeprom/eeprom.txt b/Documentation/devicetree/bindings/eeprom/eeprom.txt deleted file mode 100644 index 27f2bc15298a..000000000000 --- a/Documentation/devicetree/bindings/eeprom/eeprom.txt +++ /dev/null @@ -1,47 +0,0 @@ -EEPROMs (I2C) - -Required properties: - - - compatible : should be "<manufacturer>,<type>", like these: - - "atmel,24c00", "atmel,24c01", "atmel,24c02", "atmel,24c04", - "atmel,24c08", "atmel,24c16", "atmel,24c32", "atmel,24c64", - "atmel,24c128", "atmel,24c256", "atmel,24c512", "atmel,24c1024" - - "catalyst,24c32" - - "microchip,24c128" - - "ramtron,24c64" - - "renesas,r1ex24002" - - The following manufacturers values have been deprecated: - "at", "at24" - - If there is no specific driver for <manufacturer>, a generic - device with <type> and manufacturer "atmel" should be used. - Possible types are: - "24c00", "24c01", "24c02", "24c04", "24c08", "24c16", "24c32", "24c64", - "24c128", "24c256", "24c512", "24c1024", "spd" - - - reg : the I2C address of the EEPROM - -Optional properties: - - - pagesize : the length of the pagesize for writing. Please consult the - manual of your device, that value varies a lot. A wrong value - may result in data loss! If not specified, a safety value of - '1' is used which will be very slow. - - - read-only: this parameterless property disables writes to the eeprom - - - size: total eeprom size in bytes - -Example: - -eeprom@52 { - compatible = "atmel,24c32"; - reg = <0x52>; - pagesize = <32>; -}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-meson.txt b/Documentation/devicetree/bindings/i2c/i2c-meson.txt index 611b934c7e10..13d410de077c 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-meson.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-meson.txt @@ -1,7 +1,11 @@ Amlogic Meson I2C controller Required properties: - - compatible: must be "amlogic,meson6-i2c" or "amlogic,meson-gxbb-i2c" + - compatible: must be: + "amlogic,meson6-i2c" for Meson8 and compatible SoCs + "amlogic,meson-gxbb-i2c" for GXBB and compatible SoCs + "amlogic,meson-axg-i2c"for AXG and compatible SoCs + - reg: physical address and length of the device registers - interrupts: a single interrupt specifier - clocks: clock for the device diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt index ff7bf37deb43..e199695b1c96 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt @@ -5,6 +5,7 @@ The MediaTek's I2C controller is used to interface with I2C devices. Required properties: - compatible: value should be either of the following. "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for MediaTek MT2701 + "mediatek,mt2712-i2c": for MediaTek MT2712 "mediatek,mt6577-i2c": for MediaTek MT6577 "mediatek,mt6589-i2c": for MediaTek MT6589 "mediatek,mt7622-i2c": for MediaTek MT7622 diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt index aa097045a10e..34d91501342e 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt @@ -1,10 +1,19 @@ * NXP PCA954x I2C bus switch +The driver supports NXP PCA954x and PCA984x I2C mux/switch devices. + Required Properties: - compatible: Must contain one of the following. - "nxp,pca9540", "nxp,pca9542", "nxp,pca9543", "nxp,pca9544", - "nxp,pca9545", "nxp,pca9546", "nxp,pca9547", "nxp,pca9548" + "nxp,pca9540", + "nxp,pca9542", + "nxp,pca9543", + "nxp,pca9544", + "nxp,pca9545", + "nxp,pca9546", "nxp,pca9846", + "nxp,pca9547", "nxp,pca9847", + "nxp,pca9548", "nxp,pca9848", + "nxp,pca9849" - reg: The I2C address of the device. diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt index 5c30026921ae..0ffe65a316ae 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt @@ -25,6 +25,15 @@ default frequency is 100kHz whenever you're using the "allwinner,sun6i-a31-i2c" compatible. + - clocks: : pointers to the reference clocks for this device, the + first one is the one used for the clock on the i2c bus, + the second one is the clock used to acces the registers + of the controller + + - clock-names : names of used clocks, mandatory if the second clock is + used, the name must be "core", and "reg" (the latter is + only for Armada 7K/8K). + Examples: i2c@11000 { @@ -42,3 +51,14 @@ For the Armada XP: interrupts = <29>; clock-frequency = <100000>; }; + +For the Armada 7040: + + i2c@701000 { + compatible = "marvell,mv78230-i2c"; + reg = <0x701000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + clock-names = "core", "reg"; + clocks = <&core_clock>, <®_clock>; + }; diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index 857df929a654..1fd5d69647ca 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -16,6 +16,9 @@ Required Properties: - "renesas,ipmmu-r8a7793" for the R8A7793 (R-Car M2-N) IPMMU. - "renesas,ipmmu-r8a7794" for the R8A7794 (R-Car E2) IPMMU. - "renesas,ipmmu-r8a7795" for the R8A7795 (R-Car H3) IPMMU. + - "renesas,ipmmu-r8a7796" for the R8A7796 (R-Car M3-W) IPMMU. + - "renesas,ipmmu-r8a77970" for the R8A77970 (R-Car V3M) IPMMU. + - "renesas,ipmmu-r8a77995" for the R8A77995 (R-Car D3) IPMMU. - "renesas,ipmmu-vmsa" for generic R-Car Gen2 VMSA-compatible IPMMU. - reg: Base address and size of the IPMMU registers. diff --git a/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt b/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt index fb961c310f44..16964f0c1773 100644 --- a/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt +++ b/Documentation/devicetree/bindings/mailbox/qcom,apcs-kpss-global.txt @@ -15,12 +15,21 @@ platforms. Usage: required Value type: <prop-encoded-array> Definition: must specify the base address and size of the global block +- clocks: + Usage: required if #clocks-cells property is present + Value type: <phandle> + Definition: phandle to the input PLL, which feeds the APCS mux/divider - #mbox-cells: Usage: required Value type: <u32> Definition: as described in mailbox.txt, must be 1 +- #clock-cells: + Usage: optional + Value type: <u32> + Definition: as described in clock.txt, must be 0 + = EXAMPLE The following example describes the APCS HMSS found in MSM8996 and part of the @@ -44,3 +53,12 @@ GLINK RPM referencing the "rpm_hlos" doorbell therein. mbox-names = "rpm_hlos"; }; +Below is another example of the APCS binding on MSM8916 platforms: + + apcs: mailbox@b011000 { + compatible = "qcom,msm8916-apcs-kpss-global"; + reg = <0xb011000 0x1000>; + #mbox-cells = <1>; + clocks = <&a53pll>; + #clock-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/media/cec-gpio.txt b/Documentation/devicetree/bindings/media/cec-gpio.txt index 46a0bac8b3b9..12fcd55ed153 100644 --- a/Documentation/devicetree/bindings/media/cec-gpio.txt +++ b/Documentation/devicetree/bindings/media/cec-gpio.txt @@ -4,6 +4,10 @@ The HDMI CEC GPIO module supports CEC implementations where the CEC line is hooked up to a pull-up GPIO line and - optionally - the HPD line is hooked up to another GPIO line. +Please note: the maximum voltage for the CEC line is 3.63V, for the HPD +line it is 5.3V. So you may need some sort of level conversion circuitry +when connecting them to a GPIO line. + Required properties: - compatible: value must be "cec-gpio". - cec-gpios: gpio that the CEC line is connected to. The line should be @@ -21,7 +25,7 @@ the following property is optional: Example for the Raspberry Pi 3 where the CEC line is connected to pin 26 aka BCM7 aka CE1 on the GPIO pin header and the HPD line is -connected to pin 11 aka BCM17: +connected to pin 11 aka BCM17 (some level shifter is needed for this!): #include <dt-bindings/gpio/gpio.h> diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt index ed5a334b1e57..6b910036b57e 100644 --- a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt +++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt @@ -6,6 +6,8 @@ interface. Required Properties: - compatible: value should be "micron,mt9m111" +- clocks: reference to the master clock. +- clock-names: shall be "mclk". For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. @@ -16,6 +18,8 @@ Example: mt9m111@5d { compatible = "micron,mt9m111"; reg = <0x5d>; + clocks = <&mclk>; + clock-names = "mclk"; remote = <&pxa_camera>; port { diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt index 540b36c4b1f2..8e36da0d8406 100644 --- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt +++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt @@ -1,4 +1,4 @@ -* Omnivision OV5640 MIPI CSI-2 sensor +* Omnivision OV5640 MIPI CSI-2 / parallel sensor Required Properties: - compatible: should be "ovti,ov5640" @@ -18,7 +18,25 @@ The device node must contain one 'port' child node for its digital output video port, in accordance with the video interface bindings defined in Documentation/devicetree/bindings/media/video-interfaces.txt. -Example: +OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint. + +Endpoint node required properties for CSI-2 connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- clock-lanes: should be set to <0> (clock lane on hardware lane 0) +- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported) + +Endpoint node required properties for parallel connection are: +- remote-endpoint: a phandle to the bus receiver's endpoint node. +- bus-width: shall be set to <8> for 8 bits parallel bus + or <10> for 10 bits parallel bus +- data-shift: shall be set to <2> for 8 bits parallel bus + (lines 9:2 are used) or <0> for 10 bits parallel bus +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. +- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock + signal. + +Examples: &i2c1 { ov5640: camera@3c { @@ -35,6 +53,7 @@ Example: reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; port { + /* MIPI CSI-2 bus endpoint */ ov5640_to_mipi_csi2: endpoint { remote-endpoint = <&mipi_csi2_from_ov5640>; clock-lanes = <0>; @@ -43,3 +62,26 @@ Example: }; }; }; + +&i2c1 { + ov5640: camera@3c { + compatible = "ovti,ov5640"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ov5640>; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + clock-names = "xclk"; + + port { + /* Parallel bus endpoint */ + ov5640_to_parallel: endpoint { + remote-endpoint = <¶llel_from_ov5640>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov7740.txt b/Documentation/devicetree/bindings/media/i2c/ov7740.txt new file mode 100644 index 000000000000..af781c3a5f0e --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov7740.txt @@ -0,0 +1,47 @@ +* Omnivision OV7740 CMOS image sensor + +The Omnivision OV7740 image sensor supports multiple output image +size, such as VGA, and QVGA, CIF and any size smaller. It also +supports the RAW RGB and YUV output formats. + +The common video interfaces bindings (see video-interfaces.txt) should +be used to specify link to the image data receiver. The OV7740 device +node should contain one 'port' child node with an 'endpoint' subnode. + +Required Properties: +- compatible: "ovti,ov7740". +- reg: I2C slave address of the sensor. +- clocks: Reference to the xvclk input clock. +- clock-names: "xvclk". + +Optional Properties: +- reset-gpios: Rreference to the GPIO connected to the reset_b pin, + if any. Active low with pull-ip resistor. +- powerdown-gpios: Reference to the GPIO connected to the pwdn pin, + if any. Active high with pull-down resistor. + +Endpoint node mandatory properties: +- remote-endpoint: A phandle to the bus receiver's endpoint node. + +Example: + + i2c1: i2c@fc028000 { + ov7740: camera@21 { + compatible = "ovti,ov7740"; + reg = <0x21>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>; + clocks = <&isc>; + clock-names = "xvclk"; + assigned-clocks = <&isc>; + assigned-clock-rates = <24000000>; + reset-gpios = <&pioA 43 GPIO_ACTIVE_LOW>; + powerdown-gpios = <&pioA 44 GPIO_ACTIVE_HIGH>; + + port { + ov7740_0: endpoint { + remote-endpoint = <&isc_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt index 0b7b6a4d84ff..e80d5891b7ed 100644 --- a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt +++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt @@ -20,6 +20,13 @@ Mandatory properties is in hardware standby mode when the signal is in the low state. +Optional properties +------------------- + +- flash-leds: See ../video-interfaces.txt +- lens-focus: See ../video-interfaces.txt + + Endpoint node mandatory properties ---------------------------------- diff --git a/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt new file mode 100644 index 000000000000..470237ed6fe5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt @@ -0,0 +1,55 @@ +NVIDIA Tegra Video Decoder Engine + +Required properties: +- compatible : Must contain one of the following values: + - "nvidia,tegra20-vde" + - "nvidia,tegra30-vde" + - "nvidia,tegra114-vde" + - "nvidia,tegra124-vde" + - "nvidia,tegra132-vde" +- reg : Must contain an entry for each entry in reg-names. +- reg-names : Must include the following entries: + - sxe + - bsev + - mbe + - ppe + - mce + - tfe + - ppb + - vdma + - frameid +- iram : Must contain phandle to the mmio-sram device node that represents + IRAM region used by VDE. +- interrupts : Must contain an entry for each entry in interrupt-names. +- interrupt-names : Must include the following entries: + - sync-token + - bsev + - sxe +- clocks : Must include the following entries: + - vde +- resets : Must include the following entries: + - vde + +Example: + +video-codec@6001a000 { + compatible = "nvidia,tegra20-vde"; + reg = <0x6001a000 0x1000 /* Syntax Engine */ + 0x6001b000 0x1000 /* Video Bitstream Engine */ + 0x6001c000 0x100 /* Macroblock Engine */ + 0x6001c200 0x100 /* Post-processing Engine */ + 0x6001c400 0x100 /* Motion Compensation Engine */ + 0x6001c600 0x100 /* Transform Engine */ + 0x6001c800 0x100 /* Pixel prediction block */ + 0x6001ca00 0x100 /* Video DMA */ + 0x6001d800 0x300 /* Video frame controls */>; + reg-names = "sxe", "bsev", "mbe", "ppe", "mce", + "tfe", "ppb", "vdma", "frameid"; + iram = <&vde_pool>; /* IRAM region */ + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, /* Sync token interrupt */ + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, /* BSE-V interrupt */ + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; /* SXE interrupt */ + interrupt-names = "sync-token", "bsev", "sxe"; + clocks = <&tegra_car TEGRA20_CLK_VDE>; + resets = <&tegra_car 61>; +}; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt index 9dd86b3db937..439351ab2a79 100644 --- a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt @@ -66,6 +66,6 @@ Example: tpg1_out: endpoint { remote-endpoint = <&switch_in0>; }; - }: + }; }; }; diff --git a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt index 4e4aee4439ea..979dc7b6cfe8 100644 --- a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt +++ b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt @@ -4,7 +4,10 @@ This PCIe host controller is based on the Synopsys DesignWare PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: -- compatible: "axis,artpec6-pcie", "snps,dw-pcie" +- compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode; + "axis,artpec6-pcie-ep", "snps,dw-pcie" for ARTPEC-6 in EP mode; + "axis,artpec7-pcie", "snps,dw-pcie" for ARTPEC-7 in RC mode; + "axis,artpec7-pcie-ep", "snps,dw-pcie" for ARTPEC-7 in EP mode; - reg: base addresses and lengths of the PCIe controller (DBI), the PHY controller, and configuration address space. - reg-names: Must include the following entries: diff --git a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt new file mode 100644 index 000000000000..9a305237fa6e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt @@ -0,0 +1,22 @@ +* Cadence PCIe endpoint controller + +Required properties: +- compatible: Should contain "cdns,cdns-pcie-ep" to identify the IP used. +- reg: Should contain the controller register base address and AXI interface + region base address respectively. +- reg-names: Must be "reg" and "mem" respectively. +- cdns,max-outbound-regions: Set to maximum number of outbound regions + +Optional properties: +- max-functions: Maximum number of functions that can be configured (default 1). + +Example: + +pcie@fc000000 { + compatible = "cdns,cdns-pcie-ep"; + reg = <0x0 0xfc000000 0x0 0x01000000>, + <0x0 0x80000000 0x0 0x40000000>; + reg-names = "reg", "mem"; + cdns,max-outbound-regions = <16>; + max-functions = /bits/ 8 <8>; +}; diff --git a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt new file mode 100644 index 000000000000..20a33f38f69d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt @@ -0,0 +1,60 @@ +* Cadence PCIe host controller + +This PCIe controller inherits the base properties defined in +host-generic-pci.txt. + +Required properties: +- compatible: Should contain "cdns,cdns-pcie-host" to identify the IP used. +- reg: Should contain the controller register base address, PCIe configuration + window base address, and AXI interface region base address respectively. +- reg-names: Must be "reg", "cfg" and "mem" respectively. +- #address-cells: Set to <3> +- #size-cells: Set to <2> +- device_type: Set to "pci" +- ranges: Ranges for the PCI memory and I/O regions +- #interrupt-cells: Set to <1> +- interrupt-map-mask and interrupt-map: Standard PCI properties to define the + mapping of the PCIe interface to interrupt numbers. + +Optional properties: +- cdns,max-outbound-regions: Set to maximum number of outbound regions + (default 32) +- cdns,no-bar-match-nbits: Set into the no BAR match register to configure the + number of least significant bits kept during inbound (PCIe -> AXI) address + translations (default 32) +- vendor-id: The PCI vendor ID (16 bits, default is design dependent) +- device-id: The PCI device ID (16 bits, default is design dependent) + +Example: + +pcie@fb000000 { + compatible = "cdns,cdns-pcie-host"; + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0xff>; + linux,pci-domain = <0>; + cdns,max-outbound-regions = <16>; + cdns,no-bar-match-nbits = <32>; + vendor-id = /bits/ 16 <0x17cd>; + device-id = /bits/ 16 <0x0200>; + + reg = <0x0 0xfb000000 0x0 0x01000000>, + <0x0 0x41000000 0x0 0x00001000>, + <0x0 0x40000000 0x0 0x04000000>; + reg-names = "reg", "cfg", "mem"; + + ranges = <0x02000000 0x0 0x42000000 0x0 0x42000000 0x0 0x1000000>, + <0x01000000 0x0 0x43000000 0x0 0x43000000 0x0 0x0010000>; + + #interrupt-cells = <0x1>; + + interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 14 0x1 + 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 15 0x1 + 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 16 0x1 + 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 17 0x1>; + + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + + msi-parent = <&its_pci>; +}; diff --git a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt index 34a11bfbfb60..651d957d1051 100644 --- a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt +++ b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt @@ -6,9 +6,6 @@ and thus inherits all the common properties defined in designware-pcie.txt. Required properties: - compatible: "samsung,exynos5440-pcie" - reg: base addresses and lengths of the PCIe controller, - the PHY controller, additional register for the PHY controller. - (Registers for the PHY controller are DEPRECATED. - Use the PHY framework.) - reg-names : First name should be set to "elbi". And use the "config" instead of getting the configuration address space from "ranges". @@ -23,49 +20,8 @@ For other common properties, refer to Example: -SoC-specific DT Entry: +SoC-specific DT Entry (with using PHY framework): - pcie@290000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x290000 0x1000 - 0x270000 0x1000 - 0x271000 0x40>; - interrupts = <0 20 0>, <0 21 0>, <0 22 0>; - clocks = <&clock 28>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; - num-lanes = <4>; - }; - - pcie@2a0000 { - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; - reg = <0x2a0000 0x1000 - 0x272000 0x1000 - 0x271040 0x40>; - interrupts = <0 23 0>, <0 24 0>, <0 25 0>; - clocks = <&clock 29>, <&clock 27>; - clock-names = "pcie", "pcie_bus"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */ - 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */ - 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */ - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0>; - interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; - num-lanes = <4>; - }; - -With using PHY framework: pcie_phy0: pcie-phy@270000 { ... reg = <0x270000 0x1000>, <0x271000 0x40>; @@ -74,13 +30,21 @@ With using PHY framework: }; pcie@290000 { - ... + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; reg = <0x290000 0x1000>, <0x40000000 0x1000>; reg-names = "elbi", "config"; + clocks = <&clock 28>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; phys = <&pcie_phy0>; ranges = <0x81000000 0 0 0x60001000 0 0x00010000 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; - ... + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <4>; }; Board-specific DT Entry: diff --git a/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt index d857b67fab72..4346ff2dd8e6 100644 --- a/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt @@ -17,6 +17,9 @@ and generic pin config nodes. Supported configurations: - skew-delay is supported on the Ethernet pins +- drive-strength with 4, 8, 12 or 16 mA as argument is supported for + entire groups on the groups "idegrp", "gmii_gmac0_grp", "gmii_gmac1_grp" + and "pcigrp". Example: diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt index a81bbf37ed66..7ca4f6118d9a 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt @@ -4,7 +4,8 @@ Please refer to fsl,imx-pinctrl.txt in this directory for common binding part and usage. Required properties: -- compatible: "fsl,imx6ul-iomuxc" +- compatible: "fsl,imx6ul-iomuxc" for main IOMUX controller or + "fsl,imx6ull-iomuxc-snvs" for i.MX 6ULL's SNVS IOMUX controller. - fsl,pins: each entry consists of 6 integers and represents the mux and config setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val input_val> are specified using a PIN_FUNC_ID macro, which can be found in diff --git a/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt new file mode 100644 index 000000000000..24a210e0c59a --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt @@ -0,0 +1,39 @@ +Microsemi Ocelot pin controller Device Tree Bindings +---------------------------------------------------- + +Required properties: + - compatible : Should be "mscc,ocelot-pinctrl" + - reg : Address and length of the register set for the device + - gpio-controller : Indicates this device is a GPIO controller + - #gpio-cells : Must be 2. + The first cell is the pin number and the + second cell specifies GPIO flags, as defined in + <dt-bindings/gpio/gpio.h>. + - gpio-ranges : Range of pins managed by the GPIO controller. + + +The ocelot-pinctrl driver uses the generic pin multiplexing and generic pin +configuration documented in pinctrl-bindings.txt. + +The following generic properties are supported: + - function + - pins + +Example: + gpio: pinctrl@71070034 { + compatible = "mscc,ocelot-pinctrl"; + reg = <0x71070034 0x28>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&gpio 0 0 22>; + + uart_pins: uart-pins { + pins = "GPIO_6", "GPIO_7"; + function = "uart"; + }; + + uart2_pins: uart2-pins { + pins = "GPIO_12", "GPIO_13"; + function = "uart2"; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt new file mode 100644 index 000000000000..f18ed99f6e14 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt7622.txt @@ -0,0 +1,351 @@ +== MediaTek MT7622 pinctrl controller == + +Required properties for the root node: + - compatible: Should be one of the following + "mediatek,mt7622-pinctrl" for MT7622 SoC + - reg: offset and length of the pinctrl space + + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be two. The first cell is the pin number and the + second is the GPIO flags. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +MT7622 pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, slew rate, etc. + +We support 2 types of configuration nodes. Those nodes can be either pinmux +nodes or pinconf nodes. Each configuration node can consist of multiple nodes +describing the pinmux and pinconf options. + +The name of each subnode doesn't matter as long as it is unique; all subnodes +should be enumerated and processed purely based on their content. + +== pinmux nodes content == + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pinmux subnode: + +Required properties are: + - groups: An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. + - function: A string containing the name of the function to mux to the + group. Valid values for function names are listed below. + +== pinconf nodes content == + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pinconf subnode: + +Required properties are: + - pins: An array of strings. Each string contains the name of a pin. + Valid values for these names are listed below. + - groups: An array of strings. Each string contains the name of a group. + Valid values for these names are listed below. + +Optional properies are: + bias-disable, bias-pull, bias-pull-down, input-enable, + input-schmitt-enable, input-schmitt-disable, output-enable + output-low, output-high, drive-strength, slew-rate + + Valid arguments for 'slew-rate' are '0' for no slew rate controlled and '1' for + slower slew rate respectively. + Valid arguments for 'drive-strength', 4, 8, 12, or 16 in mA. + +The following specific properties as defined are valid to specify in a pinconf +subnode: + +Optional properties are: + - mediatek,tdsel: An integer describing the steps for output level shifter duty + cycle when asserted (high pulse width adjustment). Valid arguments are from 0 + to 15. + - mediatek,rdsel: An integer describing the steps for input level shifter duty + cycle when asserted (high pulse width adjustment). Valid arguments are from 0 + to 63. + +== Valid values for pins, function and groups on MT7622 == + +Valid values for pins are: +pins can be referenced via the pin names as the below table shown and the +related physical number is also put ahead of those names which helps cross +references to pins between groups to know whether pins assignment conflict +happens among devices try to acquire those available pins. + + Pin #: Valid values for pins + ----------------------------- + PIN 0: "GPIO_A" + PIN 1: "I2S1_IN" + PIN 2: "I2S1_OUT" + PIN 3: "I2S_BCLK" + PIN 4: "I2S_WS" + PIN 5: "I2S_MCLK" + PIN 6: "TXD0" + PIN 7: "RXD0" + PIN 8: "SPI_WP" + PIN 9: "SPI_HOLD" + PIN 10: "SPI_CLK" + PIN 11: "SPI_MOSI" + PIN 12: "SPI_MISO" + PIN 13: "SPI_CS" + PIN 14: "I2C_SDA" + PIN 15: "I2C_SCL" + PIN 16: "I2S2_IN" + PIN 17: "I2S3_IN" + PIN 18: "I2S4_IN" + PIN 19: "I2S2_OUT" + PIN 20: "I2S3_OUT" + PIN 21: "I2S4_OUT" + PIN 22: "GPIO_B" + PIN 23: "MDC" + PIN 24: "MDIO" + PIN 25: "G2_TXD0" + PIN 26: "G2_TXD1" + PIN 27: "G2_TXD2" + PIN 28: "G2_TXD3" + PIN 29: "G2_TXEN" + PIN 30: "G2_TXC" + PIN 31: "G2_RXD0" + PIN 32: "G2_RXD1" + PIN 33: "G2_RXD2" + PIN 34: "G2_RXD3" + PIN 35: "G2_RXDV" + PIN 36: "G2_RXC" + PIN 37: "NCEB" + PIN 38: "NWEB" + PIN 39: "NREB" + PIN 40: "NDL4" + PIN 41: "NDL5" + PIN 42: "NDL6" + PIN 43: "NDL7" + PIN 44: "NRB" + PIN 45: "NCLE" + PIN 46: "NALE" + PIN 47: "NDL0" + PIN 48: "NDL1" + PIN 49: "NDL2" + PIN 50: "NDL3" + PIN 51: "MDI_TP_P0" + PIN 52: "MDI_TN_P0" + PIN 53: "MDI_RP_P0" + PIN 54: "MDI_RN_P0" + PIN 55: "MDI_TP_P1" + PIN 56: "MDI_TN_P1" + PIN 57: "MDI_RP_P1" + PIN 58: "MDI_RN_P1" + PIN 59: "MDI_RP_P2" + PIN 60: "MDI_RN_P2" + PIN 61: "MDI_TP_P2" + PIN 62: "MDI_TN_P2" + PIN 63: "MDI_TP_P3" + PIN 64: "MDI_TN_P3" + PIN 65: "MDI_RP_P3" + PIN 66: "MDI_RN_P3" + PIN 67: "MDI_RP_P4" + PIN 68: "MDI_RN_P4" + PIN 69: "MDI_TP_P4" + PIN 70: "MDI_TN_P4" + PIN 71: "PMIC_SCL" + PIN 72: "PMIC_SDA" + PIN 73: "SPIC1_CLK" + PIN 74: "SPIC1_MOSI" + PIN 75: "SPIC1_MISO" + PIN 76: "SPIC1_CS" + PIN 77: "GPIO_D" + PIN 78: "WATCHDOG" + PIN 79: "RTS3_N" + PIN 80: "CTS3_N" + PIN 81: "TXD3" + PIN 82: "RXD3" + PIN 83: "PERST0_N" + PIN 84: "PERST1_N" + PIN 85: "WLED_N" + PIN 86: "EPHY_LED0_N" + PIN 87: "AUXIN0" + PIN 88: "AUXIN1" + PIN 89: "AUXIN2" + PIN 90: "AUXIN3" + PIN 91: "TXD4" + PIN 92: "RXD4" + PIN 93: "RTS4_N" + PIN 94: "CST4_N" + PIN 95: "PWM1" + PIN 96: "PWM2" + PIN 97: "PWM3" + PIN 98: "PWM4" + PIN 99: "PWM5" + PIN 100: "PWM6" + PIN 101: "PWM7" + PIN 102: "GPIO_E" + +Valid values for function are: + "emmc", "eth", "i2c", "i2s", "ir", "led", "flash", "pcie", + "pmic", "pwm", "sd", "spi", "tdm", "uart", "watchdog" + +Valid values for groups are: +additional data is put followingly with valid value allowing us to know which +applicable function and which relevant pins (in pin#) are able applied for that +group. + + Valid value function pins (in pin#) + ------------------------------------------------------------------------- + "emmc" "emmc" 40, 41, 42, 43, 44, 45, + 47, 48, 49, 50 + "emmc_rst" "emmc" 37 + "esw" "eth" 51, 52, 53, 54, 55, 56, + 57, 58, 59, 60, 61, 62, + 63, 64, 65, 66, 67, 68, + 69, 70 + "esw_p0_p1" "eth" 51, 52, 53, 54, 55, 56, + 57, 58 + "esw_p2_p3_p4" "eth" 59, 60, 61, 62, 63, 64, + 65, 66, 67, 68, 69, 70 + "rgmii_via_esw" "eth" 59, 60, 61, 62, 63, 64, + 65, 66, 67, 68, 69, 70 + "rgmii_via_gmac1" "eth" 59, 60, 61, 62, 63, 64, + 65, 66, 67, 68, 69, 70 + "rgmii_via_gmac2" "eth" 25, 26, 27, 28, 29, 30, + 31, 32, 33, 34, 35, 36 + "mdc_mdio" "eth" 23, 24 + "i2c0" "i2c" 14, 15 + "i2c1_0" "i2c" 55, 56 + "i2c1_1" "i2c" 73, 74 + "i2c1_2" "i2c" 87, 88 + "i2c2_0" "i2c" 57, 58 + "i2c2_1" "i2c" 75, 76 + "i2c2_2" "i2c" 89, 90 + "i2s_in_mclk_bclk_ws" "i2s" 3, 4, 5 + "i2s1_in_data" "i2s" 1 + "i2s2_in_data" "i2s" 16 + "i2s3_in_data" "i2s" 17 + "i2s4_in_data" "i2s" 18 + "i2s_out_mclk_bclk_ws" "i2s" 3, 4, 5 + "i2s1_out_data" "i2s" 2 + "i2s2_out_data" "i2s" 19 + "i2s3_out_data" "i2s" 20 + "i2s4_out_data" "i2s" 21 + "ir_0_tx" "ir" 16 + "ir_1_tx" "ir" 59 + "ir_2_tx" "ir" 99 + "ir_0_rx" "ir" 17 + "ir_1_rx" "ir" 60 + "ir_2_rx" "ir" 100 + "ephy_leds" "led" 86, 91, 92, 93, 94 + "ephy0_led" "led" 86 + "ephy1_led" "led" 91 + "ephy2_led" "led" 92 + "ephy3_led" "led" 93 + "ephy4_led" "led" 94 + "wled" "led" 85 + "par_nand" "flash" 37, 38, 39, 40, 41, 42, + 43, 44, 45, 46, 47, 48, + 49, 50 + "snfi" "flash" 8, 9, 10, 11, 12, 13 + "spi_nor" "flash" 8, 9, 10, 11, 12, 13 + "pcie0_0_waken" "pcie" 14 + "pcie0_1_waken" "pcie" 79 + "pcie1_0_waken" "pcie" 14 + "pcie0_0_clkreq" "pcie" 15 + "pcie0_1_clkreq" "pcie" 80 + "pcie1_0_clkreq" "pcie" 15 + "pcie0_pad_perst" "pcie" 83 + "pcie1_pad_perst" "pcie" 84 + "pmic_bus" "pmic" 71, 72 + "pwm_ch1_0" "pwm" 51 + "pwm_ch1_1" "pwm" 73 + "pwm_ch1_2" "pwm" 95 + "pwm_ch2_0" "pwm" 52 + "pwm_ch2_1" "pwm" 74 + "pwm_ch2_2" "pwm" 96 + "pwm_ch3_0" "pwm" 53 + "pwm_ch3_1" "pwm" 75 + "pwm_ch3_2" "pwm" 97 + "pwm_ch4_0" "pwm" 54 + "pwm_ch4_1" "pwm" 67 + "pwm_ch4_2" "pwm" 76 + "pwm_ch4_3" "pwm" 98 + "pwm_ch5_0" "pwm" 68 + "pwm_ch5_1" "pwm" 77 + "pwm_ch5_2" "pwm" 99 + "pwm_ch6_0" "pwm" 69 + "pwm_ch6_1" "pwm" 78 + "pwm_ch6_2" "pwm" 81 + "pwm_ch6_3" "pwm" 100 + "pwm_ch7_0" "pwm" 70 + "pwm_ch7_1" "pwm" 82 + "pwm_ch7_2" "pwm" 101 + "sd_0" "sd" 16, 17, 18, 19, 20, 21 + "sd_1" "sd" 25, 26, 27, 28, 29, 30 + "spic0_0" "spi" 63, 64, 65, 66 + "spic0_1" "spi" 79, 80, 81, 82 + "spic1_0" "spi" 67, 68, 69, 70 + "spic1_1" "spi" 73, 74, 75, 76 + "spic2_0_wp_hold" "spi" 8, 9 + "spic2_0" "spi" 10, 11, 12, 13 + "tdm_0_out_mclk_bclk_ws" "tdm" 8, 9, 10 + "tdm_0_in_mclk_bclk_ws" "tdm" 11, 12, 13 + "tdm_0_out_data" "tdm" 20 + "tdm_0_in_data" "tdm" 21 + "tdm_1_out_mclk_bclk_ws" "tdm" 57, 58, 59 + "tdm_1_in_mclk_bclk_ws" "tdm" 60, 61, 62 + "tdm_1_out_data" "tdm" 55 + "tdm_1_in_data" "tdm" 56 + "uart0_0_tx_rx" "uart" 6, 7 + "uart1_0_tx_rx" "uart" 55, 56 + "uart1_0_rts_cts" "uart" 57, 58 + "uart1_1_tx_rx" "uart" 73, 74 + "uart1_1_rts_cts" "uart" 75, 76 + "uart2_0_tx_rx" "uart" 3, 4 + "uart2_0_rts_cts" "uart" 1, 2 + "uart2_1_tx_rx" "uart" 51, 52 + "uart2_1_rts_cts" "uart" 53, 54 + "uart2_2_tx_rx" "uart" 59, 60 + "uart2_2_rts_cts" "uart" 61, 62 + "uart2_3_tx_rx" "uart" 95, 96 + "uart3_0_tx_rx" "uart" 57, 58 + "uart3_1_tx_rx" "uart" 81, 82 + "uart3_1_rts_cts" "uart" 79, 80 + "uart4_0_tx_rx" "uart" 61, 62 + "uart4_1_tx_rx" "uart" 91, 92 + "uart4_1_rts_cts" "uart" 93, 94 + "uart4_2_tx_rx" "uart" 97, 98 + "uart4_2_rts_cts" "uart" 95, 96 + "watchdog" "watchdog" 78 + +Example: + + pio: pinctrl@10211000 { + compatible = "mediatek,mt7622-pinctrl"; + reg = <0 0x10211000 0 0x1000>; + gpio-controller; + #gpio-cells = <2>; + + pinctrl_eth_default: eth-default { + mux-mdio { + groups = "mdc_mdio"; + function = "eth"; + drive-strength = <12>; + }; + + mux-gmac2 { + groups = "gmac2"; + function = "eth"; + drive-strength = <12>; + }; + + mux-esw { + groups = "esw"; + function = "eth"; + drive-strength = <8>; + }; + + conf-mdio { + pins = "MDC"; + bias-pull-up; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt new file mode 100644 index 000000000000..e70c79bbbc5b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.txt @@ -0,0 +1,193 @@ +Qualcomm MSM8998 TLMM block + +This binding describes the Top Level Mode Multiplexer block found in the +MSM8998 platform. + +- compatible: + Usage: required + Value type: <string> + Definition: must be "qcom,msm8998-pinctrl" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of the TLMM register space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the TLMM summary IRQ. + +- interrupt-controller: + Usage: required + Value type: <none> + Definition: identifies this node as an interrupt controller + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/interrupt-controller/irq.h> + +- gpio-controller: + Usage: required + Value type: <none> + Definition: identifies this node as a gpio controller + +- #gpio-cells: + Usage: required + Value type: <u32> + Definition: must be 2. Specifying the pin number and flags, as defined + in <dt-bindings/gpio/gpio.h> + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + + +PIN CONFIGURATION NODES: + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + +- pins: + Usage: required + Value type: <string-array> + Definition: List of gpio pins affected by the properties specified in + this subnode. + + Valid pins are: + gpio0-gpio149 + Supports mux, bias and drive-strength + + sdc2_clk, sdc2_cmd, sdc2_data + Supports bias and drive-strength + + ufs_reset + Supports bias and drive-strength + +- function: + Usage: required + Value type: <string> + Definition: Specify the alternative function to be configured for the + specified pins. Functions are only valid for gpio pins. + Valid values are: + + gpio, adsp_ext, agera_pll, atest_char, atest_gpsadc0, + atest_gpsadc1, atest_tsens, atest_tsens2, atest_usb1, + atest_usb10, atest_usb11, atest_usb12, atest_usb13, + audio_ref, bimc_dte0, bimc_dte1, blsp10_spi, blsp10_spi_a, + blsp10_spi_b, blsp11_i2c, blsp1_spi, blsp1_spi_a, + blsp1_spi_b, blsp2_spi, blsp9_spi, blsp_i2c1, blsp_i2c2, + blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, + blsp_i2c8, blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12, + blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, + blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10, + blsp_spi11, blsp_spi12, blsp_uart1_a, blsp_uart1_b, + blsp_uart2_a, blsp_uart2_b, blsp_uart3_a, blsp_uart3_b, + blsp_uart7_a, blsp_uart7_b, blsp_uart8, blsp_uart8_a, + blsp_uart8_b, blsp_uart9_a, blsp_uart9_b, blsp_uim1_a, + blsp_uim1_b, blsp_uim2_a, blsp_uim2_b, blsp_uim3_a, + blsp_uim3_b, blsp_uim7_a, blsp_uim7_b, blsp_uim8_a, + blsp_uim8_b, blsp_uim9_a, blsp_uim9_b, bt_reset, + btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0, + cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng, + cri_trng0, cri_trng1, dbg_out, ddr_bist, edp_hot, edp_lcd, + gcc_gp1_a, gcc_gp1_b, gcc_gp2_a, gcc_gp2_b, gcc_gp3_a, + gcc_gp3_b, hdmi_cec, hdmi_ddc, hdmi_hot, hdmi_rcv, + isense_dbg, jitter_bist, ldo_en, ldo_update, lpass_slimbus, + m_voc, mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2, + mdp_vsync3, mdp_vsync_a, mdp_vsync_b, modem_tsync, mss_lte, + nav_dr, nav_pps, pa_indicator, pci_e0, phase_flag, + pll_bypassnl, pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc, + pwr_crypto, pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b, + qdss_cti1_a, qdss_cti1_b, qdss, qlink_enable, + qlink_request, qua_mi2s, sd_card, sd_write, sdc40, sdc41, + sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, + spkr_i2s, ssbi1, ssc_irq, ter_mi2s, tgu_ch0, tgu_ch1, + tsense_pwm1, tsense_pwm2, tsif1_clk, tsif1_data, tsif1_en, + tsif1_error, tsif1_sync, tsif2_clk, tsif2_data, tsif2_en, + tsif2_error, tsif2_sync, uim1_clk, uim1_data, uim1_present, + uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset, + uim_batt, usb_phy, vfr_1, vsense_clkout, vsense_data0, + vsense_data1, vsense_mode, wlan1_adc0, wlan1_adc1, + wlan2_adc0, wlan2_adc1, + +- bias-disable: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as no pull. + +- bias-pull-down: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull down. + +- bias-pull-up: + Usage: optional + Value type: <none> + Definition: The specified pins should be configued as pull up. + +- output-high: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + high. + Not valid for sdc pins. + +- output-low: + Usage: optional + Value type: <none> + Definition: The specified pins are configured in output mode, driven + low. + Not valid for sdc pins. + +- drive-strength: + Usage: optional + Value type: <u32> + Definition: Selects the drive strength for the specified pins, in mA. + Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 + +Example: + + tlmm: pinctrl@03400000 { + compatible = "qcom,msm8998-pinctrl"; + reg = <0x03400000 0xc00000>; + interrupts = <0 208 0>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + uart_console_active: uart_console_active { + mux { + pins = "gpio4", "gpio5"; + function = "blsp_uart8_a"; + }; + + config { + pins = "gpio4", "gpio5"; + drive-strength = <2>; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 9b4f8041c36a..bb1790e0b176 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -24,6 +24,7 @@ Required Properties: - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller. - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller. - "renesas,pfc-r8a7796": for R8A7796 (R-Car M3-W) compatible pin-controller. + - "renesas,pfc-r8a77970": for R8A77970 (R-Car V3M) compatible pin-controller. - "renesas,pfc-r8a77995": for R8A77995 (R-Car D3) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. diff --git a/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.txt new file mode 100644 index 000000000000..8173b12138ad --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.txt @@ -0,0 +1,27 @@ +UniPhier SoCs pin controller + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-ld4-pinctrl" - for LD4 SoC + "socionext,uniphier-pro4-pinctrl" - for Pro4 SoC + "socionext,uniphier-sld8-pinctrl" - for sLD8 SoC + "socionext,uniphier-pro5-pinctrl" - for Pro5 SoC + "socionext,uniphier-pxs2-pinctrl" - for PXs2 SoC + "socionext,uniphier-ld6b-pinctrl" - for LD6b SoC + "socionext,uniphier-ld11-pinctrl" - for LD11 SoC + "socionext,uniphier-ld20-pinctrl" - for LD20 SoC + "socionext,uniphier-pxs3-pinctrl" - for PXs3 SoC + +Note: +The UniPhier pinctrl should be a subnode of a "syscon" compatible node. + +Example: + soc-glue@5f800000 { + compatible = "socionext,uniphier-pro4-soc-glue", + "simple-mfd", "syscon"; + reg = <0x5f800000 0x2000>; + + pinctrl: pinctrl { + compatible = "socionext,uniphier-pro4-pinctrl"; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index 58c2a4c229db..2c46f30b62c5 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -12,6 +12,8 @@ Required properies: "st,stm32f469-pinctrl" "st,stm32f746-pinctrl" "st,stm32h743-pinctrl" + "st,stm32mp157-pinctrl" + "st,stm32mp157-z-pinctrl" - #address-cells: The value of this property must be 1 - #size-cells : The value of this property must be 1 - ranges : defines mapping between pin controller node (parent) to diff --git a/Documentation/devicetree/bindings/pwm/pwm-meson.txt b/Documentation/devicetree/bindings/pwm/pwm-meson.txt index 1ee81321c35e..1fa3f7182133 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-meson.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-meson.txt @@ -5,6 +5,8 @@ Required properties: - compatible: Shall contain "amlogic,meson8b-pwm" or "amlogic,meson-gxbb-pwm" or "amlogic,meson-gxbb-ao-pwm" + or "amlogic,meson-axg-ee-pwm" + or "amlogic,meson-axg-ao-pwm" - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/rtc/rtc-mxc_v2.txt b/Documentation/devicetree/bindings/rtc/rtc-mxc_v2.txt new file mode 100644 index 000000000000..79d7e87b0d91 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-mxc_v2.txt @@ -0,0 +1,17 @@ +* i.MX53 Secure Real Time Clock (SRTC) + +Required properties: +- compatible: should be: "fsl,imx53-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: should contain the phandle for the rtc clock +- interrupts: rtc alarm interrupt + +Example: + +rtc@53fa4000 { + compatible = "fsl,imx53-rtc"; + reg = <0x53fa4000 0x4000>; + interrupts = <24>; + clocks = <&clks IMX5_CLK_SRTC_GATE>; +}; diff --git a/Documentation/devicetree/bindings/thermal/armada-thermal.txt b/Documentation/devicetree/bindings/thermal/armada-thermal.txt index 24aacf8948c5..e0d013a2e66d 100644 --- a/Documentation/devicetree/bindings/thermal/armada-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/armada-thermal.txt @@ -2,22 +2,35 @@ Required properties: -- compatible: Should be set to one of the following: - marvell,armada370-thermal - marvell,armada375-thermal - marvell,armada380-thermal - marvell,armadaxp-thermal +- compatible: Should be set to one of the following: + * marvell,armada370-thermal + * marvell,armada375-thermal + * marvell,armada380-thermal + * marvell,armadaxp-thermal + * marvell,armada-ap806-thermal + * marvell,armada-cp110-thermal -- reg: Device's register space. - Two entries are expected, see the examples below. - The first one is required for the sensor register; - the second one is required for the control register - to be used for sensor initialization (a.k.a. calibration). +- reg: Device's register space. + Two entries are expected, see the examples below. The first one points + to the status register (4B). The second one points to the control + registers (8B). + Note: The compatibles marvell,armada370-thermal, + marvell,armada380-thermal, and marvell,armadaxp-thermal must point to + "control MSB/control 1", with size of 4 (deprecated binding), or point + to "control LSB/control 0" with size of 8 (current binding). All other + compatibles must point to "control LSB/control 0" with size of 8. -Example: +Examples: + /* Legacy bindings */ thermal@d0018300 { compatible = "marvell,armada370-thermal"; - reg = <0xd0018300 0x4 + reg = <0xd0018300 0x4 0xd0018304 0x4>; }; + + ap_thermal: thermal@6f8084 { + compatible = "marvell,armada-ap806-thermal"; + reg = <0x6f808C 0x4>, + <0x6f8084 0x8>; + }; diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index a8e52c8ccfcc..349e635f2d87 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -6,6 +6,7 @@ Required properties: "renesas,rcar-thermal" (without thermal-zone) as fallback. Examples with soctypes are: - "renesas,thermal-r8a73a4" (R-Mobile APE6) + - "renesas,thermal-r8a7743" (RZ/G1M) - "renesas,thermal-r8a7779" (R-Car H1) - "renesas,thermal-r8a7790" (R-Car H2) - "renesas,thermal-r8a7791" (R-Car M2-W) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index b1fa64a1d4d0..ae850d6c0ad3 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -125,6 +125,7 @@ focaltech FocalTech Systems Co.,Ltd friendlyarm Guangzhou FriendlyARM Computer Tech Co., Ltd fsl Freescale Semiconductor fujitsu Fujitsu Ltd. +gcw Game Consoles Worldwide ge General Electric Company geekbuying GeekBuying gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. diff --git a/Documentation/devicetree/bindings/watchdog/cortina,gemini-watchdog.txt b/Documentation/devicetree/bindings/watchdog/cortina,gemini-watchdog.txt deleted file mode 100644 index bc4b865d178b..000000000000 --- a/Documentation/devicetree/bindings/watchdog/cortina,gemini-watchdog.txt +++ /dev/null @@ -1,17 +0,0 @@ -Cortina Systems Gemini SoC Watchdog - -Required properties: -- compatible : must be "cortina,gemini-watchdog" -- reg : shall contain base register location and length -- interrupts : shall contain the interrupt for the watchdog - -Optional properties: -- timeout-sec : the default watchdog timeout in seconds. - -Example: - -watchdog@41000000 { - compatible = "cortina,gemini-watchdog"; - reg = <0x41000000 0x1000>; - interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; -}; diff --git a/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt b/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.txt index bc4b865d178b..9ecdb502e605 100644 --- a/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt +++ b/Documentation/devicetree/bindings/watchdog/faraday,ftwdt010.txt @@ -1,7 +1,12 @@ -Cortina Systems Gemini SoC Watchdog +Faraday Technology FTWDT010 watchdog + +This is an IP part from Faraday Technology found in the Gemini +SoCs and others. Required properties: -- compatible : must be "cortina,gemini-watchdog" +- compatible : must be one of + "faraday,ftwdt010" + "cortina,gemini-watchdog", "faraday,ftwdt010" - reg : shall contain base register location and length - interrupts : shall contain the interrupt for the watchdog @@ -11,7 +16,7 @@ Optional properties: Example: watchdog@41000000 { - compatible = "cortina,gemini-watchdog"; + compatible = "faraday,ftwdt010"; reg = <0x41000000 0x1000>; interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; }; diff --git a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt index 3c7a1cd13b10..cb44918f01a8 100644 --- a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt @@ -1,7 +1,7 @@ -Ingenic Watchdog Timer (WDT) Controller for JZ4740 +Ingenic Watchdog Timer (WDT) Controller for JZ4740 & JZ4780 Required properties: -compatible: "ingenic,jz4740-watchdog" +compatible: "ingenic,jz4740-watchdog" or "ingenic,jz4780-watchdog" reg: Register address and length for watchdog registers Example: diff --git a/Documentation/devicetree/bindings/watchdog/realtek,rtd119x.txt b/Documentation/devicetree/bindings/watchdog/realtek,rtd119x.txt new file mode 100644 index 000000000000..05653054bd5b --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/realtek,rtd119x.txt @@ -0,0 +1,17 @@ +Realtek RTD1295 Watchdog +======================== + +Required properties: + +- compatible : Should be "realtek,rtd1295-watchdog" +- reg : Specifies the physical base address and size of registers +- clocks : Specifies one clock input + + +Example: + + watchdog@98007680 { + compatible = "realtek,rtd1295-watchdog"; + reg = <0x98007680 0x100>; + clocks = <&osc27M>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index bf6d1ca58af7..74b2f03c1515 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -4,10 +4,11 @@ Required properties: - compatible : Should be "renesas,<soctype>-wdt", and "renesas,rcar-gen3-wdt" or "renesas,rza-wdt" as fallback. Examples with soctypes are: + - "renesas,r7s72100-wdt" (RZ/A1) - "renesas,r8a7795-wdt" (R-Car H3) - "renesas,r8a7796-wdt" (R-Car M3-W) + - "renesas,r8a77970-wdt" (R-Car V3M) - "renesas,r8a77995-wdt" (R-Car D3) - - "renesas,r7s72100-wdt" (RZ/A1) When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the generic diff --git a/Documentation/devicetree/bindings/watchdog/sprd-wdt.txt b/Documentation/devicetree/bindings/watchdog/sprd-wdt.txt new file mode 100644 index 000000000000..aeaf3e0caf47 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/sprd-wdt.txt @@ -0,0 +1,19 @@ +Spreadtrum SoCs Watchdog timer + +Required properties: +- compatible : Should be "sprd,sp9860-wdt". +- reg : Specifies base physical address and size of the registers. +- interrupts : Exactly one interrupt specifier. +- timeout-sec : Contain the default watchdog timeout in seconds. +- clock-names : Contain the input clock names. +- clocks : Phandles to input clocks. + +Example: + watchdog: watchdog@40310000 { + compatible = "sprd,sp9860-wdt"; + reg = <0 0x40310000 0 0x1000>; + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + timeout-sec = <12>; + clock-names = "enable", "rtc_enable"; + clocks = <&clk_aon_apb_gates1 8>, <&clk_aon_apb_rtc_gates 9>; + }; |