diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
9 files changed, 128 insertions, 32 deletions
diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt index ba5ecc1041a5..2fefa1a44afd 100644 --- a/Documentation/devicetree/bindings/net/brcm,amac.txt +++ b/Documentation/devicetree/bindings/net/brcm,amac.txt @@ -2,11 +2,17 @@ Broadcom AMAC Ethernet Controller Device Tree Bindings ------------------------------------------------------------- Required properties: - - compatible: "brcm,amac" or "brcm,nsp-amac" - - reg: Address and length of the GMAC registers, - Address and length of the GMAC IDM registers - - reg-names: Names of the registers. Must have both "amac_base" and - "idm_base" + - compatible: "brcm,amac" + "brcm,nsp-amac" + "brcm,ns2-amac" + - reg: Address and length of the register set for the device. It + contains the information of registers in the same order as + described by reg-names + - reg-names: Names of the registers. + "amac_base": Address and length of the GMAC registers + "idm_base": Address and length of the GMAC IDM registers + "nicpm_base": Address and length of the NIC Port Manager + registers (required for Northstar2) - interrupts: Interrupt number Optional properties: diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt index 7629189398aa..b3dd6b40e0de 100644 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -14,22 +14,42 @@ The properties described here are those specific to Marvell devices. Additional required and optional properties can be found in dsa.txt. Required properties: -- compatible : Should be one of "marvell,mv88e6085", +- compatible : Should be one of "marvell,mv88e6085" or + "marvell,mv88e6190" - reg : Address on the MII bus for the switch. Optional properties: - reset-gpios : Should be a gpio specifier for a reset line - +- interrupt-parent : Parent interrupt controller +- interrupts : Interrupt from the switch +- interrupt-controller : Indicates the switch is itself an interrupt + controller. This is used for the PHY interrupts. +#interrupt-cells = <2> : Controller uses two cells, number and flag +- mdio : container of PHY and devices on the switches MDIO + bus Example: mdio { #address-cells = <1>; #size-cells = <0>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; switch0: switch@0 { compatible = "marvell,mv88e6085"; reg = <0>; reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; }; + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + interrupt-parent = <&switch0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt index d4b7f2e49984..abfbeecbcf39 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -45,6 +45,12 @@ Required properties: depends on the hardware user manual. - port-mode-offset: is offset of port mode field for each port in dsaf. Its value depends on the hardware user manual. +- mc-mac-mask: mask of multicast address, determines bit in multicast address + to set: + 1 stands for this bit will be precisely matched, TCAM will check this bit of + MAC address. + 0 stands for this bit will be fuzzy matched, TCAM won't care about this bit + of MAC address. [1] Documentation/devicetree/bindings/net/phy.txt @@ -74,10 +80,12 @@ dsaf0: dsa@c7000000 { reg = 0; phy-handle = <&phy0>; serdes-syscon = <&serdes>; + mc-mac-mask = [ff f0 00 00 00 00]; }; port@1 { reg = 1; serdes-syscon = <&serdes>; + mc-mac-mask = [ff f0 00 00 00 00]; }; }; diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt index 8516929c7251..065e8bdb957d 100644 --- a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt +++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt @@ -3,7 +3,7 @@ Properties for an MDIO bus multiplexer controlled by a memory-mapped device This is a special case of a MDIO bus multiplexer. A memory-mapped device, like an FPGA, is used to control which child bus is connected. The mdio-mux node must be a child of the memory-mapped device. The driver currently only -supports devices with eight-bit registers. +supports devices with 8, 16 or 32-bit registers. Required properties in addition to the generic multiplexer properties: @@ -11,7 +11,7 @@ Required properties in addition to the generic multiplexer properties: - reg : integer, contains the offset of the register that controls the bus multiplexer. The size field in the 'reg' property is the size of - register, and must therefore be 1. + register, and must therefore be 1, 2, or 4. - mux-mask : integer, contains an eight-bit mask that specifies which bits in the register control the actual bus multiplexer. The diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt index 99c7eb0a00c8..bdefefc66594 100644 --- a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -6,22 +6,27 @@ Required properties: Documentation/devicetree/bindings/net/phy.txt Optional properties: -- vsc8531,vddmac : The vddmac in mV. +- vsc8531,vddmac : The vddmac in mV. Allowed values is listed + in the first row of Table 1 (below). + This property is only used in combination + with the 'edge-slowdown' property. + Default value is 3300. - vsc8531,edge-slowdown : % the edge should be slowed down relative to - the fastest possible edge time. Native sign - need not enter. + the fastest possible edge time. Edge rate sets the drive strength of the MAC - interface output signals. Changing the drive - strength will affect the edge rate of the output - signal. The goal of this setting is to help - reduce electrical emission (EMI) by being able - to reprogram drive strength and in effect slow - down the edge rate if desired. Table 1 shows the - impact to the edge rate per VDDMAC supply for each - drive strength setting. - Ref: Table:1 - Edge rate change below. - -Note: see dt-bindings/net/mscc-phy-vsc8531.h for applicable values + interface output signals. Changing the + drive strength will affect the edge rate of + the output signal. The goal of this setting + is to help reduce electrical emission (EMI) + by being able to reprogram drive strength + and in effect slow down the edge rate if + desired. + To adjust the edge-slowdown, the 'vddmac' + must be specified. Table 1 lists the + supported edge-slowdown values for a given + 'vddmac'. + Default value is 0%. + Ref: Table:1 - Edge rate change (below). Table: 1 - Edge rate change ----------------------------------------------------------------| @@ -29,23 +34,23 @@ Table: 1 - Edge rate change | | | 3300 mV 2500 mV 1800 mV 1500 mV | |---------------------------------------------------------------| -| Default Deafult Default Default | +| 0% 0% 0% 0% | | (Fastest) (recommended) (recommended) | |---------------------------------------------------------------| -| -2% -3% -5% -6% | +| 2% 3% 5% 6% | |---------------------------------------------------------------| -| -4% -6% -9% -14% | +| 4% 6% 9% 14% | |---------------------------------------------------------------| -| -7% -10% -16% -21% | +| 7% 10% 16% 21% | |(recommended) (recommended) | |---------------------------------------------------------------| -| -10% -14% -23% -29% | +| 10% 14% 23% 29% | |---------------------------------------------------------------| -| -17% -23% -35% -42% | +| 17% 23% 35% 42% | |---------------------------------------------------------------| -| -29% -37% -52% -58% | +| 29% 37% 52% 58% | |---------------------------------------------------------------| -| -53% -63% -76% -77% | +| 53% 63% 76% 77% | | (slowest) | |---------------------------------------------------------------| @@ -54,5 +59,5 @@ Example: vsc8531_0: ethernet-phy@0 { compatible = "ethernet-phy-id0007.0570"; vsc8531,vddmac = <3300>; - vsc8531,edge-slowdown = <21>; + vsc8531,edge-slowdown = <7>; }; diff --git a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt new file mode 100644 index 000000000000..df0534e2eda1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt @@ -0,0 +1,39 @@ +* Oxford Semiconductor OXNAS DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file stmmac.txt in the current directory with the +following changes. + +Required properties on all platforms: + +- compatible: For the OX820 SoC, it should be : + - "oxsemi,ox820-dwmac" to select glue + - "snps,dwmac-3.512" to select IP version. + +- clocks: Should contain phandles to the following clocks +- clock-names: Should contain the following: + - "stmmaceth" for the host clock - see stmmac.txt + - "gmac" for the peripheral gate clock + +- oxsemi,sys-ctrl: a phandle to the system controller syscon node + +Example : + +etha: ethernet@40400000 { + compatible = "oxsemi,ox820-dwmac", "snps,dwmac-3.512"; + reg = <0x40400000 0x2000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "rgmii"; + + clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>; + clock-names = "gmac", "stmmaceth"; + resets = <&reset RESET_MAC>; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index bc1c3c8bf8fa..4627da3d52c4 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -35,6 +35,10 @@ Optional Properties: - broken-turn-around: If set, indicates the PHY device does not correctly release the turn around line low at the end of a MDIO transaction. +- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to + compensate for the board being designed with the lanes swapped. + + Example: ethernet-phy@0 { diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt index e77e167593db..309e37eb7c7c 100644 --- a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt +++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt @@ -13,3 +13,5 @@ Optional properties: 16-bit access only. - power-gpios: GPIO to control the PWRDWN pin - reset-gpios: GPIO to control the RESET pin +- pxa-u16-align4 : Boolean, put in place the workaround the force all + u16 writes to be 32 bits aligned diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 5d21141a68b5..85bf945b898f 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -9,6 +9,18 @@ Required properties: - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable values +Optional property: + - ti,min-output-impedance - MAC Interface Impedance control to set + the programmable output impedance to + minimum value (35 ohms). + - ti,max-output-impedance - MAC Interface Impedance control to set + the programmable output impedance to + maximum value (70 ohms). + +Note: ti,min-output-impedance and ti,max-output-impedance are mutually + exclusive. When both properties are present ti,max-output-impedance + takes precedence. + Default child nodes are standard Ethernet PHY device nodes as described in Documentation/devicetree/bindings/net/phy.txt |