diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
107 files changed, 2477 insertions, 113 deletions
diff --git a/Documentation/devicetree/bindings/arm/actions.txt b/Documentation/devicetree/bindings/arm/actions.txt index 3bc7ea575564..ced764a8549e 100644 --- a/Documentation/devicetree/bindings/arm/actions.txt +++ b/Documentation/devicetree/bindings/arm/actions.txt @@ -21,6 +21,7 @@ Boards: Root node property compatible must contain, depending on board: + - Cubietech CubieBoard6: "cubietech,cubieboard6" - LeMaker Guitar Base Board rev. B: "lemaker,guitar-bb-rev-b", "lemaker,guitar" diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 4e4bc0bae597..f747f47922c5 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -41,6 +41,10 @@ Boards with the Amlogic Meson GXM S912 SoC shall have the following properties: Required root node property: compatible: "amlogic,s912", "amlogic,meson-gxm"; +Boards with the Amlogic Meson AXG A113D SoC shall have the following properties: + Required root node property: + compatible: "amlogic,a113d", "amlogic,meson-axg"; + Board compatible values (alphabetically, grouped by SoC): - "geniatech,atv1200" (Meson6) @@ -71,8 +75,12 @@ Board compatible values (alphabetically, grouped by SoC): - "amlogic,q200" (Meson gxm s912) - "amlogic,q201" (Meson gxm s912) + - "khadas,vim2" (Meson gxm s912) - "kingnovel,r-box-pro" (Meson gxm S912) - "nexbox,a1" (Meson gxm s912) + - "tronsmart,vega-s96" (Meson gxm s912) + + - "amlogic,s400" (Meson axg a113d) Amlogic Meson Firmware registers Interface ------------------------------------------ diff --git a/Documentation/devicetree/bindings/arm/amlogic/analog-top.txt b/Documentation/devicetree/bindings/arm/amlogic/analog-top.txt new file mode 100644 index 000000000000..101dc21014ec --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic/analog-top.txt @@ -0,0 +1,20 @@ +Amlogic Meson8 and Meson8b "analog top" registers: +-------------------------------------------------- + +The analog top registers contain information about the so-called +"metal revision" (which encodes the "minor version") of the SoC. + +Required properties: +- reg: the register range of the analog top registers +- compatible: depending on the SoC this should be one of: + - "amlogic,meson8-analog-top" + - "amlogic,meson8b-analog-top" + along with "syscon" + + +Example: + + analog_top: analog-top@81a8 { + compatible = "amlogic,meson8-analog-top", "syscon"; + reg = <0x81a8 0x14>; + }; diff --git a/Documentation/devicetree/bindings/arm/amlogic/assist.txt b/Documentation/devicetree/bindings/arm/amlogic/assist.txt new file mode 100644 index 000000000000..7656812b67b9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic/assist.txt @@ -0,0 +1,17 @@ +Amlogic Meson6/Meson8/Meson8b assist registers: +----------------------------------------------- + +The assist registers contain basic information about the SoC, +for example the encoded SoC part number. + +Required properties: +- reg: the register range of the assist registers +- compatible: should be "amlogic,meson-mx-assist" along with "syscon" + + +Example: + + assist: assist@7c00 { + compatible = "amlogic,meson-mx-assist", "syscon"; + reg = <0x7c00 0x200>; + }; diff --git a/Documentation/devicetree/bindings/arm/amlogic/bootrom.txt b/Documentation/devicetree/bindings/arm/amlogic/bootrom.txt new file mode 100644 index 000000000000..407e27f230ab --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic/bootrom.txt @@ -0,0 +1,17 @@ +Amlogic Meson6/Meson8/Meson8b bootrom: +-------------------------------------- + +The bootrom register area can be used to access SoC specific +information, such as the "misc version". + +Required properties: +- reg: the register range of the bootrom registers +- compatible: should be "amlogic,meson-mx-bootrom" along with "syscon" + + +Example: + + bootrom: bootrom@d9040000 { + compatible = "amlogic,meson-mx-bootrom", "syscon"; + reg = <0xd9040000 0x10000>; + }; diff --git a/Documentation/devicetree/bindings/arm/amlogic/pmu.txt b/Documentation/devicetree/bindings/arm/amlogic/pmu.txt new file mode 100644 index 000000000000..72f8d08198b6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic/pmu.txt @@ -0,0 +1,18 @@ +Amlogic Meson8 and Meson8b power-management-unit: +------------------------------------------------- + +The pmu is used to turn off and on different power domains of the SoCs +This includes the power to the CPU cores. + +Required node properties: +- compatible value : depending on the SoC this should be one of: + "amlogic,meson8-pmu" + "amlogic,meson8b-pmu" +- reg : physical base address and the size of the registers window + +Example: + + pmu@c81000e4 { + compatible = "amlogic,meson8b-pmu", "syscon"; + reg = <0xc81000e0 0x18>; + }; diff --git a/Documentation/devicetree/bindings/arm/amlogic/smp-sram.txt b/Documentation/devicetree/bindings/arm/amlogic/smp-sram.txt new file mode 100644 index 000000000000..3473ddaadfac --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic/smp-sram.txt @@ -0,0 +1,32 @@ +Amlogic Meson8 and Meson8b SRAM for smp bringup: +------------------------------------------------ + +Amlogic's SMP-capable SoCs use part of the sram for the bringup of the cores. +Once the core gets powered up it executes the code that is residing at a +specific location. + +Therefore a reserved section sub-node has to be added to the mmio-sram +declaration. + +Required sub-node properties: +- compatible : depending on the SoC this should be one of: + "amlogic,meson8-smp-sram" + "amlogic,meson8b-smp-sram" + +The rest of the properties should follow the generic mmio-sram discription +found in ../../misc/sram.txt + +Example: + + sram: sram@d9000000 { + compatible = "mmio-sram"; + reg = <0xd9000000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0xd9000000 0x20000>; + + smp-sram@1ff80 { + compatible = "amlogic,meson8b-smp-sram"; + reg = <0x1ff80 0x8>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt index 0d0c1ae81bed..790e6b0b8306 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt @@ -164,6 +164,8 @@ Control registers for this memory controller's DDR PHY. Required properties: - compatible : should contain one of these + "brcm,brcmstb-ddr-phy-v71.1" + "brcm,brcmstb-ddr-phy-v72.0" "brcm,brcmstb-ddr-phy-v225.1" "brcm,brcmstb-ddr-phy-v240.1" "brcm,brcmstb-ddr-phy-v240.2" @@ -184,7 +186,9 @@ Sequencer DRAM parameters and control registers. Used for Self-Refresh Power-Down (SRPD), among other things. Required properties: -- compatible : should contain "brcm,brcmstb-memc-ddr" +- compatible : should contain one of these + "brcm,brcmstb-memc-ddr-rev-b.2.2" + "brcm,brcmstb-memc-ddr" - reg : the MEMC DDR register range Example: diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,hr2.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,hr2.txt new file mode 100644 index 000000000000..a124c7fc4dcd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,hr2.txt @@ -0,0 +1,14 @@ +Broadcom Hurricane 2 device tree bindings +--------------------------------------- + +Broadcom Hurricane 2 family of SoCs are used for switching control. These SoCs +are based on Broadcom's iProc SoC architecture and feature a single core Cortex +A9 ARM CPUs, DDR2/DDR3 memory, PCIe GEN-2, USB 2.0 and USB 3.0, serial and NAND +flash and a PCIe attached integrated switching engine. + +Boards with Hurricane SoCs shall have the following properties: + +Required root node property: + +BCM53342 +compatible = "brcm,bcm53342", "brcm,hr2"; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index b92f12bd5244..a0009b72e9be 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -197,6 +197,8 @@ described below. "actions,s500-smp" "allwinner,sun6i-a31" "allwinner,sun8i-a23" + "amlogic,meson8-smp" + "amlogic,meson8b-smp" "arm,realview-smp" "brcm,bcm11351-cpu-method" "brcm,bcm23550" diff --git a/Documentation/devicetree/bindings/arm/omap/ctrl.txt b/Documentation/devicetree/bindings/arm/omap/ctrl.txt index 3a4e5901ce31..ce8dabf8c0f9 100644 --- a/Documentation/devicetree/bindings/arm/omap/ctrl.txt +++ b/Documentation/devicetree/bindings/arm/omap/ctrl.txt @@ -21,6 +21,8 @@ Required properties: "ti,omap3-scm" "ti,omap4-scm-core" "ti,omap4-scm-padconf-core" + "ti,omap4-scm-wkup" + "ti,omap4-scm-padconf-wkup" "ti,omap5-scm-core" "ti,omap5-scm-padconf-core" "ti,dra7-scm-core" diff --git a/Documentation/devicetree/bindings/arm/realtek.txt b/Documentation/devicetree/bindings/arm/realtek.txt index 13d755787b4f..95839e19ae92 100644 --- a/Documentation/devicetree/bindings/arm/realtek.txt +++ b/Documentation/devicetree/bindings/arm/realtek.txt @@ -12,6 +12,8 @@ Required root node properties: Root node property compatible must contain, depending on board: + - MeLE V9: "mele,v9" + - ProBox2 AVA: "probox2,ava" - Zidoo X9S: "zidoo,x9s" diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index b003148e2945..326d24bca1a9 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -1,5 +1,9 @@ Rockchip platforms device tree bindings --------------------------------------- +- Amarula Vyasa RK3288 board + Required root node properties: + - compatible = "amarula,vyasa-rk3288", "rockchip,rk3288"; + - Asus Tinker board Required root node properties: - compatible = "asus,rk3288-tinker", "rockchip,rk3288"; diff --git a/Documentation/devicetree/bindings/arm/samsung/pmu.txt b/Documentation/devicetree/bindings/arm/samsung/pmu.txt index 088584a98cf4..779f5614bcee 100644 --- a/Documentation/devicetree/bindings/arm/samsung/pmu.txt +++ b/Documentation/devicetree/bindings/arm/samsung/pmu.txt @@ -4,7 +4,6 @@ Properties: - compatible : should contain two values. First value must be one from following list: - "samsung,exynos3250-pmu" - for Exynos3250 SoC, - "samsung,exynos4210-pmu" - for Exynos4210 SoC, - - "samsung,exynos4212-pmu" - for Exynos4212 SoC, - "samsung,exynos4412-pmu" - for Exynos4412 SoC, - "samsung,exynos5250-pmu" - for Exynos5250 SoC, - "samsung,exynos5260-pmu" - for Exynos5260 SoC. diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index fa674818e7e8..e13459618581 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -57,6 +57,7 @@ Required root node properties: - "hardkernel,odroid-xu3-lite" - for Exynos5422-based Hardkernel Odroid XU3 Lite board. - "hardkernel,odroid-xu4" - for Exynos5422-based Hardkernel Odroid XU4. + - "hardkernel,odroid-hc1" - for Exynos5422-based Hardkernel Odroid HC1. * Insignal - "insignal,arndale" - for Exynos5250-based Insignal Arndale board. diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index ae75cb3b1331..020d758fc0c5 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -39,6 +39,8 @@ SoCs: compatible = "renesas,r8a7795" - R-Car M3-W (R8A77960) compatible = "renesas,r8a7796" + - R-Car V3M (R8A77970) + compatible = "renesas,r8a77970" - R-Car D3 (R8A77995) compatible = "renesas,r8a77995" @@ -57,6 +59,8 @@ Boards: compatible = "renesas,bockw", "renesas,r8a7778" - Draak (RTP0RC77995SEB0010S) compatible = "renesas,draak", "renesas,r8a77995" + - Eagle (RTP0RC77970SEB0010S) + compatible = "renesas,eagle", "renesas,r8a77970" - Genmai (RTK772100BC00000BR) compatible = "renesas,genmai", "renesas,r7s72100" - GR-Peach (X28A-M01-E/F) @@ -65,7 +69,7 @@ Boards: compatible = "renesas,gose", "renesas,r8a7793" - H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKBX0010SA00 (H3 ES1.1)) H3ULCB (R-Car Starter Kit Premier, RTP0RC77951SKBX010SA00 (H3 ES2.0)) - compatible = "renesas,h3ulcb", "renesas,r8a7795"; + compatible = "renesas,h3ulcb", "renesas,r8a7795" - Henninger compatible = "renesas,henninger", "renesas,r8a7791" - iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D) @@ -76,6 +80,8 @@ Boards: compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7743" - iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven) compatible = "iwave,g20m", "renesas,r8a7743" + - Kingfisher (SBEV-RCAR-KF-M03) + compatible = "shimafuji,kingfisher" - Koelsch (RTP0RC7791SEB00010S) compatible = "renesas,koelsch", "renesas,r8a7791" - Kyoto Microcomputer Co. KZM-A9-Dual @@ -85,7 +91,7 @@ Boards: - Lager (RTP0RC7790SEB00010S) compatible = "renesas,lager", "renesas,r8a7790" - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKBX0010SA09 (M3 ES1.0)) - compatible = "renesas,m3ulcb", "renesas,r8a7796"; + compatible = "renesas,m3ulcb", "renesas,r8a7796" - Marzen (R0P7779A00010S) compatible = "renesas,marzen", "renesas,r8a7779" - Porter (M2-LCDP) @@ -93,11 +99,11 @@ Boards: - RSKRZA1 (YR0K77210C000BE) compatible = "renesas,rskrza1", "renesas,r7s72100" - Salvator-X (RTP0RC7795SIPB0010S) - compatible = "renesas,salvator-x", "renesas,r8a7795"; + compatible = "renesas,salvator-x", "renesas,r8a7795" - Salvator-X (RTP0RC7796SIPB0011S) - compatible = "renesas,salvator-x", "renesas,r8a7796"; + compatible = "renesas,salvator-x", "renesas,r8a7796" - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S) - compatible = "renesas,salvator-xs", "renesas,r8a7795"; + compatible = "renesas,salvator-xs", "renesas,r8a7795" - SILK (RTP0RC7794LCB00011S) compatible = "renesas,silk", "renesas,r8a7794" - SK-RZG1E (YR8A77450S000BE) diff --git a/Documentation/devicetree/bindings/arm/spe-pmu.txt b/Documentation/devicetree/bindings/arm/spe-pmu.txt new file mode 100644 index 000000000000..93372f2a7df9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spe-pmu.txt @@ -0,0 +1,20 @@ +* ARMv8.2 Statistical Profiling Extension (SPE) Performance Monitor Units (PMU) + +ARMv8.2 introduces the optional Statistical Profiling Extension for collecting +performance sample data using an in-memory trace buffer. + +** SPE Required properties: + +- compatible : should be one of: + "arm,statistical-profiling-extension-v1" + +- interrupts : Exactly 1 PPI must be listed. For heterogeneous systems where + SPE is only supported on a subset of the CPUs, please consult + the arm,gic-v3 binding for details on describing a PPI partition. + +** Example: + +spe-pmu { + compatible = "arm,statistical-profiling-extension-v1"; + interrupts = <GIC_PPI 05 IRQ_TYPE_LEVEL_HIGH &part1>; +}; diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt index d2c46449b4eb..e4beec3d9ad3 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.txt +++ b/Documentation/devicetree/bindings/arm/sunxi.txt @@ -14,6 +14,8 @@ using one of the following compatible strings: allwinner,sun8i-a83t allwinner,sun8i-h2-plus allwinner,sun8i-h3 + allwinner-sun8i-r40 + allwinner,sun8i-v3s allwinner,sun9i-a80 allwinner,sun50i-a64 nextthing,gr8 diff --git a/Documentation/devicetree/bindings/ata/ahci-ceva.txt b/Documentation/devicetree/bindings/ata/ahci-ceva.txt index 7ca8b976c13a..7561cc4de371 100644 --- a/Documentation/devicetree/bindings/ata/ahci-ceva.txt +++ b/Documentation/devicetree/bindings/ata/ahci-ceva.txt @@ -5,6 +5,36 @@ Required properties: - compatible: Compatibility string. Must be 'ceva,ahci-1v84'. - clocks: Input clock specifier. Refer to common clock bindings. - interrupts: Interrupt specifier. Refer to interrupt binding. + - ceva,p0-cominit-params: OOB timing value for COMINIT parameter for port 0. + - ceva,p1-cominit-params: OOB timing value for COMINIT parameter for port 1. + The fields for the above parameter must be as shown below: + ceva,pN-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>; + CINMP : COMINIT Negate Minimum Period. + CIBGN : COMINIT Burst Gap Nominal. + CIBGMX: COMINIT Burst Gap Maximum. + CIBGMN: COMINIT Burst Gap Minimum. + - ceva,p0-comwake-params: OOB timing value for COMWAKE parameter for port 0. + - ceva,p1-comwake-params: OOB timing value for COMWAKE parameter for port 1. + The fields for the above parameter must be as shown below: + ceva,pN-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>; + CWBGMN: COMWAKE Burst Gap Minimum. + CWBGMX: COMWAKE Burst Gap Maximum. + CWBGN: COMWAKE Burst Gap Nominal. + CWNMP: COMWAKE Negate Minimum Period. + - ceva,p0-burst-params: Burst timing value for COM parameter for port 0. + - ceva,p1-burst-params: Burst timing value for COM parameter for port 1. + The fields for the above parameter must be as shown below: + ceva,pN-burst-params = /bits/ 8 <BMX BNM SFD PTST>; + BMX: COM Burst Maximum. + BNM: COM Burst Nominal. + SFD: Signal Failure Detection value. + PTST: Partial to Slumber timer value. + - ceva,p0-retry-params: Retry interval timing value for port 0. + - ceva,p1-retry-params: Retry interval timing value for port 1. + The fields for the above parameter must be as shown below: + ceva,pN-retry-params = /bits/ 16 <RIT RCT>; + RIT: Retry Interval Timer. + RCT: Rate Change Timer. Optional properties: - ceva,broken-gen2: limit to gen1 speed instead of gen2. @@ -16,5 +46,14 @@ Examples: interrupt-parent = <&gic>; interrupts = <0 133 4>; clocks = <&clkc SATA_CLK_ID>; + ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; + ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; + ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; + ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>; + + ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>; + ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>; + ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>; + ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>; ceva,broken-gen2; }; diff --git a/Documentation/devicetree/bindings/bus/ti-sysc.txt b/Documentation/devicetree/bindings/bus/ti-sysc.txt new file mode 100644 index 000000000000..fb1790e39398 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/ti-sysc.txt @@ -0,0 +1,93 @@ +Texas Instruments sysc interconnect target module wrapper binding + +Texas Instruments SoCs can have a generic interconnect target module +hardware for devices connected to various interconnects such as L3 +interconnect (Arteris NoC) and L4 interconnect (Sonics s3220). The sysc +is mostly used for interaction between module and PRCM. It participates +in the OCP Disconnect Protocol but other than that is mostly independent +of the interconnect. + +Each interconnect target module can have one or more devices connected to +it. There is a set of control registers for managing interconnect target +module clocks, idle modes and interconnect level resets for the module. + +These control registers are sprinkled into the unused register address +space of the first child device IP block managed by the interconnect +target module and typically are named REVISION, SYSCONFIG and SYSSTATUS. + +Required standard properties: + +- compatible shall be one of the following generic types: + + "ti,sysc-omap2" + "ti,sysc-omap4" + "ti,sysc-omap4-simple" + + or one of the following derivative types for hardware + needing special workarounds: + + "ti,sysc-omap3430-sr" + "ti,sysc-omap3630-sr" + "ti,sysc-omap4-sr" + "ti,sysc-omap3-sham" + "ti,sysc-omap-aes" + "ti,sysc-mcasp" + "ti,sysc-usb-host-fs" + +- reg shall have register areas implemented for the interconnect + target module in question such as revision, sysc and syss + +- reg-names shall contain the register names implemented for the + interconnect target module in question such as + "rev, "sysc", and "syss" + +- ranges shall contain the interconnect target module IO range + available for one or more child device IP blocks managed + by the interconnect target module, the ranges may include + multiple ranges such as device L4 range for control and + parent L3 range for DMA access + +Optional properties: + +- clocks clock specifier for each name in the clock-names as + specified in the binding documentation for ti-clkctrl, + typically available for all interconnect targets on TI SoCs + based on omap4 except if it's read-only register in hwauto + mode as for example omap4 L4_CFG_CLKCTRL + +- clock-names should contain at least "fck", and optionally also "ick" + depending on the SoC and the interconnect target module + +- ti,hwmods optional TI interconnect module name to use legacy + hwmod platform data + + +Example: Single instance of MUSB controller on omap4 using interconnect ranges +using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000): + + target-module@2b000 { /* 0x4a0ab000, ap 84 12.0 */ + compatible = "ti,sysc-omap2"; + ti,hwmods = "usb_otg_hs"; + reg = <0x2b400 0x4>, + <0x2b404 0x4>, + <0x2b408 0x4>; + reg-names = "rev", "sysc", "syss"; + clocks = <&l3_init_clkctrl OMAP4_USB_OTG_HS_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2b000 0x1000>; + + usb_otg_hs: otg@0 { + compatible = "ti,omap4-musb"; + reg = <0x0 0x7ff>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; + usb-phy = <&usb2_phy>; + ... + }; + }; + +Note that other SoCs, such as am335x can have multipe child devices. On am335x +there are two MUSB instances, two USB PHY instances, and a single CPPI41 DMA +instance as children of a single interconnet target module. diff --git a/Documentation/devicetree/bindings/bus/ts-nbus.txt b/Documentation/devicetree/bindings/bus/ts-nbus.txt new file mode 100644 index 000000000000..2a10d065b9fa --- /dev/null +++ b/Documentation/devicetree/bindings/bus/ts-nbus.txt @@ -0,0 +1,50 @@ +Technologic Systems NBUS + +The NBUS is a bus used to interface with peripherals in the Technologic +Systems FPGA on the TS-4600 SoM. + +Required properties : + - compatible : "technologic,ts-nbus" + - #address-cells : must be 1 + - #size-cells : must be 0 + - pwms : The PWM bound to the FPGA + - ts,data-gpios : The 8 GPIO pins connected to the data lines on the FPGA + - ts,csn-gpios : The GPIO pin connected to the csn line on the FPGA + - ts,txrx-gpios : The GPIO pin connected to the txrx line on the FPGA + - ts,strobe-gpios : The GPIO pin connected to the stobe line on the FPGA + - ts,ale-gpios : The GPIO pin connected to the ale line on the FPGA + - ts,rdy-gpios : The GPIO pin connected to the rdy line on the FPGA + +Child nodes: + +The NBUS node can contain zero or more child nodes representing peripherals +on the bus. + +Example: + + nbus { + compatible = "technologic,ts-nbus"; + pinctrl-0 = <&nbus_pins>; + #address-cells = <1>; + #size-cells = <0>; + pwms = <&pwm 2 83>; + ts,data-gpios = <&gpio0 0 GPIO_ACTIVE_HIGH + &gpio0 1 GPIO_ACTIVE_HIGH + &gpio0 2 GPIO_ACTIVE_HIGH + &gpio0 3 GPIO_ACTIVE_HIGH + &gpio0 4 GPIO_ACTIVE_HIGH + &gpio0 5 GPIO_ACTIVE_HIGH + &gpio0 6 GPIO_ACTIVE_HIGH + &gpio0 7 GPIO_ACTIVE_HIGH>; + ts,csn-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + ts,txrx-gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>; + ts,strobe-gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>; + ts,ale-gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>; + ts,rdy-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + + watchdog@2a { + compatible = "..."; + + /* ... */ + }; + }; diff --git a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt index f2c5f0e4a363..f8e4a93466cb 100644 --- a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt +++ b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt @@ -137,6 +137,20 @@ These clock IDs are defined in: ch1_audio audiopll 2 BCM_CYGNUS_AUDIOPLL_CH1 ch2_audio audiopll 3 BCM_CYGNUS_AUDIOPLL_CH2 +Hurricane 2 +------ +PLL and leaf clock compatible strings for Hurricane 2 are: + "brcm,hr2-armpll" + +The following table defines the set of PLL/clock for Hurricane 2: + + Clock Source Index ID + --- ----- ----- --------- + crystal N/A N/A N/A + + armpll crystal N/A N/A + + Northstar and Northstar Plus ------ PLL and leaf clock compatible strings for Northstar and Northstar Plus are: diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 06668bca7ffc..0047b1394c70 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -68,6 +68,8 @@ Optional properties: - adi,disable-timing-generator: Only for ADV7533. Disables the internal timing generator. The chip will rely on the sync signals in the DSI data lanes, rather than generate its own timings for HDMI output. +- clocks: from common clock binding: reference to the CEC clock. +- clock-names: from common clock binding: must be "cec". Required nodes: @@ -89,6 +91,8 @@ Example reg = <39>; interrupt-parent = <&gpio3>; interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + clocks = <&cec_clock>; + clock-names = "cec"; adi,input-depth = <8>; adi,input-colorspace = "rgb"; diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt index b1a8929c2536..3a72a103a18a 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt @@ -37,7 +37,7 @@ Optional properties: Example: - hdmi0: hdmi0@fead0000 { + hdmi0: hdmi@fead0000 { compatible = "renesas,r8a7795-dw-hdmi"; reg = <0 0xfead0000 0 0x10000>; interrupts = <0 389 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/display/bridge/sii9234.txt b/Documentation/devicetree/bindings/display/bridge/sii9234.txt new file mode 100644 index 000000000000..88041ba23d56 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/sii9234.txt @@ -0,0 +1,49 @@ +Silicon Image SiI9234 HDMI/MHL bridge bindings + +Required properties: + - compatible : "sil,sii9234". + - reg : I2C address for TPI interface, use 0x39 + - avcc33-supply : MHL/USB Switch Supply Voltage (3.3V) + - iovcc18-supply : I/O Supply Voltage (1.8V) + - avcc12-supply : TMDS Analog Supply Voltage (1.2V) + - cvcc12-supply : Digital Core Supply Voltage (1.2V) + - interrupts, interrupt-parent: interrupt specifier of INT pin + - reset-gpios: gpio specifier of RESET pin (active low) + - video interfaces: Device node can contain two video interface port + nodes for HDMI encoder and connector according to [1]. + - port@0 - MHL to HDMI + - port@1 - MHL to connector + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + + +Example: + sii9234@39 { + compatible = "sil,sii9234"; + reg = <0x39>; + avcc33-supply = <&vcc33mhl>; + iovcc18-supply = <&vcc18mhl>; + avcc12-supply = <&vsil12>; + cvcc12-supply = <&vsil12>; + reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpf3>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mhl_to_hdmi: endpoint { + remote-endpoint = <&hdmi_to_mhl>; + }; + }; + port@1 { + reg = <1>; + mhl_to_connector: endpoint { + remote-endpoint = <&connector_to_mhl>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/faraday,tve200.txt b/Documentation/devicetree/bindings/display/faraday,tve200.txt new file mode 100644 index 000000000000..82e3bc0b7485 --- /dev/null +++ b/Documentation/devicetree/bindings/display/faraday,tve200.txt @@ -0,0 +1,54 @@ +* Faraday TV Encoder TVE200 + +Required properties: + +- compatible: must be one of: + "faraday,tve200" + "cortina,gemini-tvc", "faraday,tve200" + +- reg: base address and size of the control registers block + +- interrupts: contains an interrupt specifier for the interrupt + line from the TVE200 + +- clock-names: should contain "PCLK" for the clock line clocking the + silicon and "TVE" for the 27MHz clock to the video driver + +- clocks: contains phandle and clock specifier pairs for the entries + in the clock-names property. See + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Optional properties: + +- resets: contains the reset line phandle for the block + +Required sub-nodes: + +- port: describes LCD panel signals, following the common binding + for video transmitter interfaces; see + Documentation/devicetree/bindings/media/video-interfaces.txt + This port should have the properties: + reg = <0>; + It should have one endpoint connected to a remote endpoint where + the display is connected. + +Example: + +display-controller@6a000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "faraday,tve200"; + reg = <0x6a000000 0x1000>; + interrupts = <13 IRQ_TYPE_EDGE_RISING>; + resets = <&syscon GEMINI_RESET_TVC>; + clocks = <&syscon GEMINI_CLK_GATE_TVC>, + <&syscon GEMINI_CLK_TVC>; + clock-names = "PCLK", "TVE"; + + port@0 { + reg = <0>; + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index fa00e62e1cf6..a6671bd2c85a 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -13,16 +13,16 @@ Required properties: - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: Phandles to device clocks. - clock-names: the following clocks are required: - * "mdp_core_clk" - * "iface_clk" - * "bus_clk" - * "core_mmss_clk" - * "byte_clk" - * "pixel_clk" - * "core_clk" + * "mdp_core" + * "iface" + * "bus" + * "core_mmss" + * "byte" + * "pixel" + * "core" For DSIv2, we need an additional clock: - * "src_clk" -- assigned-clocks: Parents of "byte_clk" and "pixel_clk" for the given platform. + * "src" +- assigned-clocks: Parents of "byte" and "pixel" for the given platform. - assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided by a DSI PHY block. See [1] for details on clock bindings. - vdd-supply: phandle to vdd regulator device node @@ -101,7 +101,7 @@ Required properties: - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: Phandles to device clocks. See [1] for details on clock bindings. - clock-names: the following clocks are required: - * "iface_clk" + * "iface" - vddio-supply: phandle to vdd-io regulator device node Optional properties: @@ -123,13 +123,13 @@ Example: reg = <0xfd922800 0x200>; power-domains = <&mmcc MDSS_GDSC>; clock-names = - "bus_clk", - "byte_clk", - "core_clk", - "core_mmss_clk", - "iface_clk", - "mdp_core_clk", - "pixel_clk"; + "bus", + "byte", + "core", + "core_mmss", + "iface", + "mdp_core", + "pixel"; clocks = <&mmcc MDSS_AXI_CLK>, <&mmcc MDSS_BYTE0_CLK>, @@ -207,7 +207,7 @@ Example: reg = <0xfd922a00 0xd4>, <0xfd922b00 0x2b0>, <0xfd922d80 0x7b>; - clock-names = "iface_clk"; + clock-names = "iface"; clocks = <&mmcc MDSS_AHB_CLK>; #clock-cells = <1>; vddio-supply = <&pma8084_l12>; diff --git a/Documentation/devicetree/bindings/display/msm/edp.txt b/Documentation/devicetree/bindings/display/msm/edp.txt index e63032be5401..95ce19ca7bc5 100644 --- a/Documentation/devicetree/bindings/display/msm/edp.txt +++ b/Documentation/devicetree/bindings/display/msm/edp.txt @@ -12,11 +12,11 @@ Required properties: - clocks: device clocks See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. - clock-names: the following clocks are required: - * "core_clk" - * "iface_clk" - * "mdp_core_clk" - * "pixel_clk" - * "link_clk" + * "core" + * "iface" + * "mdp_core" + * "pixel" + * "link" - #clock-cells: The value should be 1. - vdda-supply: phandle to vdda regulator device node - lvl-vdd-supply: phandle to regulator device node which is used to supply power @@ -41,11 +41,11 @@ Example: interrupts = <12 0>; power-domains = <&mmcc MDSS_GDSC>; clock-names = - "core_clk", - "pixel_clk", - "iface_clk", - "link_clk", - "mdp_core_clk"; + "core", + "pixel", + "iface", + "link", + "mdp_core"; clocks = <&mmcc MDSS_EDPAUX_CLK>, <&mmcc MDSS_EDPPIXEL_CLK>, diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt index 2d306f402d18..5f90a40da51b 100644 --- a/Documentation/devicetree/bindings/display/msm/hdmi.txt +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt @@ -64,9 +64,9 @@ Example: interrupts = <GIC_SPI 79 0>; power-domains = <&mmcc MDSS_GDSC>; clock-names = - "core_clk", - "master_iface_clk", - "slave_iface_clk"; + "core", + "master_iface", + "slave_iface"; clocks = <&mmcc HDMI_APP_CLK>, <&mmcc HDMI_M_AHB_CLK>, @@ -92,7 +92,7 @@ Example: <0x4a00500 0x100>; #phy-cells = <0>; power-domains = <&mmcc MDSS_GDSC>; - clock-names = "slave_iface_clk"; + clock-names = "slave_iface"; clocks = <&mmcc HDMI_S_AHB_CLK>; core-vdda-supply = <&pm8921_hdmi_mvs>; }; diff --git a/Documentation/devicetree/bindings/display/msm/mdp5.txt b/Documentation/devicetree/bindings/display/msm/mdp5.txt index 30c11ea83754..1b31977a68ba 100644 --- a/Documentation/devicetree/bindings/display/msm/mdp5.txt +++ b/Documentation/devicetree/bindings/display/msm/mdp5.txt @@ -22,16 +22,16 @@ Required properties: Documentation/devicetree/bindings/power/power_domain.txt - clocks: device clocks. See ../clocks/clock-bindings.txt for details. - clock-names: the following clocks are required. - * "iface_clk" - * "bus_clk" - * "vsync_clk" + * "iface" + * "bus" + * "vsync" - #address-cells: number of address cells for the MDSS children. Should be 1. - #size-cells: Should be 1. - ranges: parent bus address space is the same as the child bus address space. Optional properties: - clock-names: the following clocks are optional: - * "lut_clk" + * "lut" MDP5: Required properties: @@ -45,10 +45,10 @@ Required properties: through MDP block - clocks: device clocks. See ../clocks/clock-bindings.txt for details. - clock-names: the following clocks are required. -- * "bus_clk" -- * "iface_clk" -- * "core_clk" -- * "vsync_clk" +- * "bus" +- * "iface" +- * "core" +- * "vsync" - ports: contains the list of output ports from MDP. These connect to interfaces that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a special case since it is a part of the MDP block itself). @@ -77,7 +77,7 @@ Required properties: Optional properties: - clock-names: the following clocks are optional: - * "lut_clk" + * "lut" Example: @@ -95,9 +95,9 @@ Example: clocks = <&gcc GCC_MDSS_AHB_CLK>, <&gcc GCC_MDSS_AXI_CLK>, <&gcc GCC_MDSS_VSYNC_CLK>; - clock-names = "iface_clk", - "bus_clk", - "vsync_clk" + clock-names = "iface", + "bus", + "vsync" interrupts = <0 72 0>; @@ -120,10 +120,10 @@ Example: <&gcc GCC_MDSS_AXI_CLK>, <&gcc GCC_MDSS_MDP_CLK>, <&gcc GCC_MDSS_VSYNC_CLK>; - clock-names = "iface_clk", - "bus_clk", - "core_clk", - "vsync_clk"; + clock-names = "iface", + "bus", + "core", + "vsync"; ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/panel/orisetech,otm8009a.txt b/Documentation/devicetree/bindings/display/panel/orisetech,otm8009a.txt new file mode 100644 index 000000000000..6862028e7b2e --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/orisetech,otm8009a.txt @@ -0,0 +1,21 @@ +Orise Tech OTM8009A 3.97" 480x800 TFT LCD panel (MIPI-DSI video mode) + +The Orise Tech OTM8009A is a 3.97" 480x800 TFT LCD panel connected using +a MIPI-DSI video interface. Its backlight is managed through the DSI link. + +Required properties: + - compatible: "orisetech,otm8009a" + - reg: the virtual channel number of a DSI peripheral + +Optional properties: + - reset-gpios: a GPIO spec for the reset pin (active low). + +Example: +&dsi { + ... + panel@0 { + compatible = "orisetech,otm8009a"; + reg = <0>; + reset-gpios = <&gpioh 7 GPIO_ACTIVE_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt new file mode 100644 index 000000000000..e9e19c059260 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt @@ -0,0 +1,49 @@ +This binding covers the official 7" (800x480) Raspberry Pi touchscreen +panel. + +This DSI panel contains: + +- TC358762 DSI->DPI bridge +- Atmel microcontroller on I2C for power sequencing the DSI bridge and + controlling backlight +- Touchscreen controller on I2C for touch input + +and this binding covers the DSI display parts but not its touch input. + +Required properties: +- compatible: Must be "raspberrypi,7inch-touchscreen-panel" +- reg: Must be "45" +- port: See panel-common.txt + +Example: + +dsi1: dsi@7e700000 { + #address-cells = <1>; + #size-cells = <0>; + <...> + + port { + dsi_out_port: endpoint { + remote-endpoint = <&panel_dsi_port>; + }; + }; +}; + +i2c_dsi: i2c { + compatible = "i2c-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&gpio 28 0 + &gpio 29 0>; + + lcd@45 { + compatible = "raspberrypi,7inch-touchscreen-panel"; + reg = <0x45>; + + port { + panel_dsi_port: endpoint { + remote-endpoint = <&dsi_out_port>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt new file mode 100644 index 000000000000..3f1a8392af7f --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt @@ -0,0 +1,24 @@ +Samsung S6E63J0X03 1.63" 320x320 AMOLED panel (interface: MIPI-DSI command mode) + +Required properties: + - compatible: "samsung,s6e63j0x03" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: I/O voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin (active low) + - te-gpios: a GPIO spec for the tearing effect synchronization signal + gpio pin (active high) + +Example: +&dsi { + ... + + panel@0 { + compatible = "samsung,s6e63j0x03"; + reg = <0>; + vdd3-supply = <&ldo16_reg>; + vci-supply = <&ldo20_reg>; + reset-gpios = <&gpe0 1 GPIO_ACTIVE_LOW>; + te-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.txt b/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.txt new file mode 100644 index 000000000000..aae57ef36cdd --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.txt @@ -0,0 +1,23 @@ +Seiko Instruments Inc. 4.3" WVGA (800 x RGB x 480) TFT with Touch-Panel + +Required properties: +- compatible: should be "sii,43wvf1g". +- "dvdd-supply": 3v3 digital regulator. +- "avdd-supply": 5v analog regulator. + +Optional properties: +- backlight: phandle for the backlight control. + +Example: + + panel { + compatible = "sii,43wvf1g"; + backlight = <&backlight_display>; + dvdd-supply = <®_lcd_3v3>; + avdd-supply = <®_lcd_5v>; + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt b/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt new file mode 100644 index 000000000000..4c0caaf246c9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt @@ -0,0 +1,8 @@ +Toshiba 8.9" WXGA (1280x768) TFT LCD panel + +Required properties: +- compatible: should be "toshiba,lt089ac29000.txt" +- power-supply: as specified in the base binding + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt new file mode 100644 index 000000000000..da6939efdb43 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt @@ -0,0 +1,99 @@ +Rockchip RK3288 LVDS interface +================================ + +Required properties: +- compatible: matching the soc type, one of + - "rockchip,rk3288-lvds"; + +- reg: physical base address of the controller and length + of memory mapped region. +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. +- clock-names: must contain "pclk_lvds" + +- avdd1v0-supply: regulator phandle for 1.0V analog power +- avdd1v8-supply: regulator phandle for 1.8V analog power +- avdd3v3-supply: regulator phandle for 3.3V analog power + +- rockchip,grf: phandle to the general register files syscon +- rockchip,output: "rgb", "lvds" or "duallvds", This describes the output interface + +Optional properties: +- pinctrl-names: must contain a "lcdc" entry. +- pinctrl-0: pin control group to be used for this controller. + +Required nodes: + +The lvds has two video ports as described by + Documentation/devicetree/bindings/media/video-interfaces.txt +Their connections are modeled using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt. + +- video port 0 for the VOP input, the remote endpoint maybe vopb or vopl +- video port 1 for either a panel or subsequent encoder + +the lvds panel described by + Documentation/devicetree/bindings/display/panel/simple-panel.txt + +Panel required properties: +- ports for remote LVDS output + +Panel optional properties: +- data-mapping: should be "vesa-24","jeida-24" or "jeida-18". +This describes decribed by: + Documentation/devicetree/bindings/display/panel/panel-lvds.txt + +Example: + +lvds_panel: lvds-panel { + compatible = "auo,b101ean01"; + enable-gpios = <&gpio7 21 GPIO_ACTIVE_HIGH>; + data-mapping = "jeida-24"; + + ports { + panel_in_lvds: endpoint { + remote-endpoint = <&lvds_out_panel>; + }; + }; +}; + +For Rockchip RK3288: + + lvds: lvds@ff96c000 { + compatible = "rockchip,rk3288-lvds"; + rockchip,grf = <&grf>; + reg = <0xff96c000 0x4000>; + clocks = <&cru PCLK_LVDS_PHY>; + clock-names = "pclk_lvds"; + pinctrl-names = "lcdc"; + pinctrl-0 = <&lcdc_ctl>; + avdd1v0-supply = <&vdd10_lcd>; + avdd1v8-supply = <&vcc18_lcd>; + avdd3v3-supply = <&vcca_33>; + rockchip,output = "rgb"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + lvds_in: port@0 { + reg = <0>; + + lvds_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_lvds>; + }; + lvds_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_lvds>; + }; + }; + + lvds_out: port@1 { + reg = <1>; + + lvds_out_panel: endpoint { + remote-endpoint = <&panel_in_lvds>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index b7faa6f6a326..50cc72ee1168 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -40,15 +40,19 @@ CEC. It is one end of the pipeline. Required properties: - compatible: value must be one of: + * allwinner,sun4i-a10-hdmi * allwinner,sun5i-a10s-hdmi + * allwinner,sun6i-a31-hdmi - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the HDMI encoder * ahb: the HDMI interface clock * mod: the HDMI module clock + * ddc: the HDMI ddc clock (A31 only) * pll-0: the first video PLL * pll-1: the second video PLL - clock-names: the clock names mentioned above + - resets: phandle to the reset control for the HDMI encoder (A31 only) - dmas: phandles to the DMA channels used by the HDMI encoder * ddc-tx: The channel for DDC transmission * ddc-rx: The channel for DDC reception @@ -83,9 +87,11 @@ The TCON acts as a timing controller for RGB, LVDS and TV interfaces. Required properties: - compatible: value must be either: + * allwinner,sun4i-a10-tcon * allwinner,sun5i-a13-tcon * allwinner,sun6i-a31-tcon * allwinner,sun6i-a31s-tcon + * allwinner,sun7i-a20-tcon * allwinner,sun8i-a33-tcon * allwinner,sun8i-v3s-tcon - reg: base address and size of memory-mapped region @@ -150,8 +156,10 @@ system. Required properties: - compatible: value must be one of: + * allwinner,sun4i-a10-display-backend * allwinner,sun5i-a13-display-backend * allwinner,sun6i-a31-display-backend + * allwinner,sun7i-a20-display-backend * allwinner,sun8i-a33-display-backend - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP @@ -182,8 +190,10 @@ deinterlacing and color space conversion. Required properties: - compatible: value must be one of: + * allwinner,sun4i-a10-display-frontend * allwinner,sun5i-a13-display-frontend * allwinner,sun6i-a31-display-frontend + * allwinner,sun7i-a20-display-frontend * allwinner,sun8i-a33-display-frontend - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP @@ -228,10 +238,12 @@ extra node. Required properties: - compatible: value must be one of: + * allwinner,sun4i-a10-display-engine * allwinner,sun5i-a10s-display-engine * allwinner,sun5i-a13-display-engine * allwinner,sun6i-a31-display-engine * allwinner,sun6i-a31s-display-engine + * allwinner,sun7i-a20-display-engine * allwinner,sun8i-a33-display-engine * allwinner,sun8i-v3s-display-engine diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index 74e1e8add5a1..844e0103fb0d 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -3,6 +3,10 @@ NVIDIA Tegra host1x Required properties: - compatible: "nvidia,tegra<chip>-host1x" - reg: Physical base address and length of the controller's registers. + For pre-Tegra186, one entry describing the whole register area. + For Tegra186, one entry for each entry in reg-names: + "vm" - VM region assigned to Linux + "hypervisor" - Hypervisor region (only if Linux acts as hypervisor) - interrupts: The interrupt outputs from the controller. - #address-cells: The number of cells used to represent physical base addresses in the host1x address space. Should be 1. diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt index d4c34774d626..7fccc20d8331 100644 --- a/Documentation/devicetree/bindings/dma/sun6i-dma.txt +++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt @@ -18,7 +18,7 @@ Required properties: - #dma-cells : Should be 1, a single cell holding a line request number Example: - dma: dma-controller@01c02000 { + dma: dma-controller@1c02000 { compatible = "allwinner,sun6i-a31-dma"; reg = <0x01c02000 0x1000>; interrupts = <0 50 4>; diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt index 20f26fbce875..7b40054be0d8 100644 --- a/Documentation/devicetree/bindings/firmware/qcom,scm.txt +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt @@ -18,6 +18,8 @@ Required properties: * Core, iface, and bus clocks required for "qcom,scm" - clock-names: Must contain "core" for the core clock, "iface" for the interface clock and "bus" for the bus clock per the requirements of the compatible. +- qcom,dload-mode: phandle to the TCSR hardware block and offset of the + download mode control register (optional) Example for MSM8916: diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt index b4ebd56d03f3..c6814d7cc2b2 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-utgard.txt @@ -13,6 +13,10 @@ Required properties: + allwinner,sun50i-h5-mali + amlogic,meson-gxbb-mali + amlogic,meson-gxl-mali + + rockchip,rk3036-mali + + rockchip,rk3066-mali + + rockchip,rk3188-mali + + rockchip,rk3228-mali + stericsson,db8500-mali - reg: Physical base address and length of the GPU registers @@ -40,10 +44,18 @@ Optional properties: Memory region to allocate from, as defined in Documentation/devicetree/bindi/reserved-memory/reserved-memory.txt + - mali-supply: + Phandle to regulator for the Mali device, as defined in + Documentation/devicetree/bindings/regulator/regulator.txt for details. + - operating-points-v2: Operating Points for the GPU, as defined in Documentation/devicetree/bindings/opp/opp.txt + - power-domains: + A power domain consumer specifier as defined in + Documentation/devicetree/bindings/power/power_domain.txt + Vendor-specific bindings ------------------------ @@ -63,6 +75,10 @@ to specify one more vendor-specific compatible, among: Required properties: * resets: phandle to the reset line for the GPU + - Rockchip variants: + Required properties: + * resets: phandle to the reset line for the GPU + - stericsson,db8500-mali Required properties: * interrupt-names and interrupts: diff --git a/Documentation/devicetree/bindings/hsi/omap-ssi.txt b/Documentation/devicetree/bindings/hsi/omap-ssi.txt index b8eca3c7810d..955e335e7e56 100644 --- a/Documentation/devicetree/bindings/hsi/omap-ssi.txt +++ b/Documentation/devicetree/bindings/hsi/omap-ssi.txt @@ -1,10 +1,12 @@ OMAP SSI controller bindings -OMAP Synchronous Serial Interface (SSI) controller implements a legacy -variant of MIPI's High Speed Synchronous Serial Interface (HSI). +OMAP3's Synchronous Serial Interface (SSI) controller implements a +legacy variant of MIPI's High Speed Synchronous Serial Interface (HSI), +while the controller found inside OMAP4 is supposed to be fully compliant +with the HSI standard. Required properties: -- compatible: Should include "ti,omap3-ssi". +- compatible: Should include "ti,omap3-ssi" or "ti,omap4-hsi" - reg-names: Contains the values "sys" and "gdd" (in this order). - reg: Contains a matching register specifier for each entry in reg-names. @@ -27,6 +29,7 @@ Each port is represented as a sub-node of the ti,omap3-ssi device. Required Port sub-node properties: - compatible: Should be set to the following value ti,omap3-ssi-port (applicable to OMAP34xx devices) + ti,omap4-hsi-port (applicable to OMAP44xx devices) - reg-names: Contains the values "tx" and "rx" (in this order). - reg: Contains a matching register specifier for each entry in reg-names. @@ -38,6 +41,10 @@ Required Port sub-node properties: property. If it's missing the port will not be enabled. +Optional properties: +- ti,hwmods: Shall contain TI interconnect module name if needed + by the SoC + Example for Nokia N900: ssi-controller@48058000 { diff --git a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt index 49ccabbfa6f3..a4ff93d6b7f3 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt @@ -8,6 +8,7 @@ Required properties: "fsl,ls1043a-msi" "fsl,ls1046a-msi" "fsl,ls1043a-v1.1-msi" + "fsl,ls1012a-msi" - msi-controller: indicates that this is a PCIe MSI controller node - reg: physical base address of the controller and length of memory mapped. - interrupts: an interrupt to the parent interrupt controller. diff --git a/Documentation/devicetree/bindings/media/cec-gpio.txt b/Documentation/devicetree/bindings/media/cec-gpio.txt new file mode 100644 index 000000000000..46a0bac8b3b9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cec-gpio.txt @@ -0,0 +1,32 @@ +* HDMI CEC GPIO driver + +The HDMI CEC GPIO module supports CEC implementations where the CEC line +is hooked up to a pull-up GPIO line and - optionally - the HPD line is +hooked up to another GPIO line. + +Required properties: + - compatible: value must be "cec-gpio". + - cec-gpios: gpio that the CEC line is connected to. The line should be + tagged as open drain. + +If the CEC line is associated with an HDMI receiver/transmitter, then the +following property is also required: + + - hdmi-phandle - phandle to the HDMI controller, see also cec.txt. + +If the CEC line is not associated with an HDMI receiver/transmitter, then +the following property is optional: + + - hpd-gpios: gpio that the HPD line is connected to. + +Example for the Raspberry Pi 3 where the CEC line is connected to +pin 26 aka BCM7 aka CE1 on the GPIO pin header and the HPD line is +connected to pin 11 aka BCM17: + +#include <dt-bindings/gpio/gpio.h> + +cec-gpio { + compatible = "cec-gpio"; + cec-gpios = <&gpio 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + hpd-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt index 26ca25b6d264..0d4fdaedc6f1 100644 --- a/Documentation/devicetree/bindings/media/exynos5-gsc.txt +++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt @@ -3,8 +3,11 @@ G-Scaler is used for scaling and color space conversion on EXYNOS5 SoCs. Required properties: -- compatible: should be "samsung,exynos5-gsc" (for Exynos 5250, 5420 and - 5422 SoCs) or "samsung,exynos5433-gsc" (Exynos 5433) +- compatible: should be one of + "samsung,exynos5250-gsc" + "samsung,exynos5420-gsc" + "samsung,exynos5433-gsc" + "samsung,exynos5-gsc" (deprecated) - reg: should contain G-Scaler physical address location and length. - interrupts: should contain G-Scaler interrupt number @@ -15,7 +18,7 @@ Optional properties: Example: gsc_0: gsc@0x13e00000 { - compatible = "samsung,exynos5-gsc"; + compatible = "samsung,exynos5250-gsc"; reg = <0x13e00000 0x1000>; interrupts = <0 85 0>; }; diff --git a/Documentation/devicetree/bindings/media/i2c/imx274.txt b/Documentation/devicetree/bindings/media/i2c/imx274.txt new file mode 100644 index 000000000000..80f2e89568e1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/imx274.txt @@ -0,0 +1,33 @@ +* Sony 1/2.5-Inch 8.51Mp CMOS Digital Image Sensor + +The Sony imx274 is a 1/2.5-inch CMOS active pixel digital image sensor with +an active array size of 3864H x 2202V. It is programmable through I2C +interface. The I2C address is fixed to 0x1a as per sensor data sheet. +Image data is sent through MIPI CSI-2, which is configured as 4 lanes +at 1440 Mbps. + + +Required Properties: +- compatible: value should be "sony,imx274" for imx274 sensor +- reg: I2C bus address of the device + +Optional Properties: +- reset-gpios: Sensor reset GPIO + +The imx274 device node should contain one 'port' child node with +an 'endpoint' subnode. For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + sensor@1a { + compatible = "sony,imx274"; + reg = <0x1a>; + #address-cells = <1>; + #size-cells = <0>; + reset-gpios = <&gpio_sensor 0 0>; + port { + sensor_out: endpoint { + remote-endpoint = <&csiss_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt index 855e1faf73e2..33f10a94c381 100644 --- a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt +++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -27,6 +27,8 @@ Optional properties - nokia,nvm-size: The size of the NVM, in bytes. If the size is not given, the NVM contents will not be read. - reset-gpios: XSHUTDOWN GPIO +- flash-leds: See ../video-interfaces.txt +- lens-focus: See ../video-interfaces.txt Endpoint node mandatory properties diff --git a/Documentation/devicetree/bindings/media/rockchip-rga.txt b/Documentation/devicetree/bindings/media/rockchip-rga.txt new file mode 100644 index 000000000000..fd5276abfad6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rockchip-rga.txt @@ -0,0 +1,33 @@ +device-tree bindings for rockchip 2D raster graphic acceleration controller (RGA) + +RGA is a standalone 2D raster graphic acceleration unit. It accelerates 2D +graphics operations, such as point/line drawing, image scaling, rotation, +BitBLT, alpha blending and image blur/sharpness. + +Required properties: +- compatible: value should be one of the following + "rockchip,rk3288-rga"; + "rockchip,rk3399-rga"; + +- interrupts: RGA interrupt specifier. + +- clocks: phandle to RGA sclk/hclk/aclk clocks + +- clock-names: should be "aclk", "hclk" and "sclk" + +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: should be "core", "axi" and "ahb" + +Example: +SoC-specific DT entry: + rga: rga@ff680000 { + compatible = "rockchip,rk3399-rga"; + reg = <0xff680000 0x10000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru ACLK_RGA>, <&cru HCLK_RGA>, <&cru SCLK_RGA_CORE>; + clock-names = "aclk", "hclk", "sclk"; + + resets = <&cru SRST_RGA_CORE>, <&cru SRST_A_RGA>, <&cru SRST_H_RGA>; + reset-names = "core, "axi", "ahb"; + }; diff --git a/Documentation/devicetree/bindings/media/tango-ir.txt b/Documentation/devicetree/bindings/media/tango-ir.txt new file mode 100644 index 000000000000..a9f00c2bf897 --- /dev/null +++ b/Documentation/devicetree/bindings/media/tango-ir.txt @@ -0,0 +1,21 @@ +Sigma Designs Tango IR NEC/RC-5/RC-6 decoder (SMP86xx and SMP87xx) + +Required properties: + +- compatible: "sigma,smp8642-ir" +- reg: address/size of NEC+RC5 area, address/size of RC6 area +- interrupts: spec for IR IRQ +- clocks: spec for IR clock (typically the crystal oscillator) + +Optional properties: + +- linux,rc-map-name: see Documentation/devicetree/bindings/media/rc.txt + +Example: + + ir@10518 { + compatible = "sigma,smp8642-ir"; + reg = <0x10518 0x18>, <0x105e0 0x1c>; + interrupts = <21 IRQ_TYPE_EDGE_RISING>; + clocks = <&xtal>; + }; diff --git a/Documentation/devicetree/bindings/media/tegra-cec.txt b/Documentation/devicetree/bindings/media/tegra-cec.txt new file mode 100644 index 000000000000..c503f06f3b84 --- /dev/null +++ b/Documentation/devicetree/bindings/media/tegra-cec.txt @@ -0,0 +1,27 @@ +* Tegra HDMI CEC hardware + +The HDMI CEC module is present in Tegra SoCs and its purpose is to +handle communication between HDMI connected devices over the CEC bus. + +Required properties: + - compatible : value should be one of the following: + "nvidia,tegra114-cec" + "nvidia,tegra124-cec" + "nvidia,tegra210-cec" + - reg : Physical base address of the IP registers and length of memory + mapped region. + - interrupts : HDMI CEC interrupt number to the CPU. + - clocks : from common clock binding: handle to HDMI CEC clock. + - clock-names : from common clock binding: must contain "cec", + corresponding to the entry in the clocks property. + - hdmi-phandle : phandle to the HDMI controller, see also cec.txt. + +Example: + +cec@70015000 { + compatible = "nvidia,tegra124-cec"; + reg = <0x0 0x70015000 0x0 0x00001000>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_CEC>; + clock-names = "cec"; +}; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt index 852041a7480c..3994b0143dd1 100644 --- a/Documentation/devicetree/bindings/media/video-interfaces.txt +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -55,6 +55,15 @@ divided into two separate ITU-R BT.656 8-bit busses. In such case bus-width and data-shift properties can be used to assign physical data lines to each endpoint node (logical bus). +Documenting bindings for devices +-------------------------------- + +All required and optional bindings the device supports shall be explicitly +documented in device DT binding documentation. This also includes port and +endpoint nodes for the device, including unit-addresses and reg properties where +relevant. + +Please also see Documentation/devicetree/bindings/graph.txt . Required properties ------------------- @@ -67,6 +76,16 @@ are required in a relevant parent node: identifier, should be 1. - #size-cells : should be zero. + +Optional properties +------------------- + +- flash-leds: An array of phandles, each referring to a flash LED, a sub-node + of the LED driver device node. + +- lens-focus: A phandle to the node of the focus lens controller. + + Optional endpoint properties ---------------------------- @@ -99,7 +118,10 @@ Optional endpoint properties determines the logical lane number, while the value of an entry indicates physical lane, e.g. for 2-lane MIPI CSI-2 bus we could have "data-lanes = <1 2>;", assuming the clock lane is on hardware lane 0. - This property is valid for serial busses only (e.g. MIPI CSI-2). + If the hardware does not support lane reordering, monotonically + incremented values shall be used from 0 or 1 onwards, depending on + whether or not there is also a clock lane. This property is valid for + serial busses only (e.g. MIPI CSI-2). - clock-lanes: an array of physical clock lane indexes. Position of an entry determines the logical lane number, while the value of an entry indicates physical lane, e.g. for a MIPI CSI-2 bus we could have "clock-lanes = <0>;", diff --git a/Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.txt b/Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.txt new file mode 100644 index 000000000000..82d923ef413f --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.txt @@ -0,0 +1,27 @@ +DDR PHY Front End (DPFE) for Broadcom STB +========================================= + +DPFE and the DPFE firmware provide an interface for the host CPU to +communicate with the DCPU, which resides inside the DDR PHY. + +There are three memory regions for interacting with the DCPU. These are +specified in a single reg property. + +Required properties: + - compatible: must be "brcm,bcm7271-dpfe-cpu", "brcm,bcm7268-dpfe-cpu" + or "brcm,dpfe-cpu" + - reg: must reference three register ranges + - start address and length of the DCPU register space + - start address and length of the DCPU data memory space + - start address and length of the DCPU instruction memory space + - reg-names: must contain "dpfe-cpu", "dpfe-dmem", and "dpfe-imem"; + they must be in the same order as the register declarations + +Example: + dpfe_cpu0: dpfe-cpu@f1132000 { + compatible = "brcm,bcm7271-dpfe-cpu", "brcm,dpfe-cpu"; + reg = <0xf1132000 0x180 + 0xf1134000 0x1000 + 0xf1138000 0x4000>; + reg-names = "dpfe-cpu", "dpfe-dmem", "dpfe-imem"; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt index 0db60470ebb6..fd823d6091b2 100644 --- a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt +++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt @@ -7,8 +7,10 @@ of the EMIF IP and memory parts attached to it. Required properties: - compatible : Should be of the form "ti,emif-<ip-rev>" where <ip-rev> - is the IP revision of the specific EMIF instance. - For am437x should be ti,emif-am4372. + is the IP revision of the specific EMIF instance. For newer controllers, + compatible should be one of the following: + "ti,emif-am3352" + "ti,emif-am4372" - phy-type : <u32> indicating the DDR phy type. Following are the allowed values diff --git a/Documentation/devicetree/bindings/mfd/aspeed-scu.txt b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt index 4fc5b83726d6..ce8cf0ec6279 100644 --- a/Documentation/devicetree/bindings/mfd/aspeed-scu.txt +++ b/Documentation/devicetree/bindings/mfd/aspeed-scu.txt @@ -9,10 +9,16 @@ Required properties: "aspeed,g5-scu", "syscon", "simple-mfd" - reg: contains the offset and length of the SCU memory region +- #clock-cells: should be set to <1> - the system controller is also a + clock provider +- #reset-cells: should be set to <1> - the system controller is also a + reset line provider Example: syscon: syscon@1e6e2000 { compatible = "aspeed,ast2400-scu", "syscon", "simple-mfd"; reg = <0x1e6e2000 0x1a8>; + #clock-cells = <1>; + #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/mfd/brcm,iproc-cdru.txt b/Documentation/devicetree/bindings/mfd/brcm,iproc-cdru.txt new file mode 100644 index 000000000000..82f82e069563 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/brcm,iproc-cdru.txt @@ -0,0 +1,16 @@ +Broadcom iProc Chip Device Resource Unit (CDRU) + +Various Broadcom iProc SoCs have a set of registers that provide various +chip specific device and resource configurations. This node allows access to +these CDRU registers via syscon. + +Required properties: +- compatible: should contain: + "brcm,sr-cdru", "syscon" for Stingray +- reg: base address and range of the CDRU registers + +Example: + cdru: syscon@6641d000 { + compatible = "brcm,sr-cdru", "syscon"; + reg = <0 0x6641d000 0 0x400>; + }; diff --git a/Documentation/devicetree/bindings/mfd/brcm,iproc-mhb.txt b/Documentation/devicetree/bindings/mfd/brcm,iproc-mhb.txt new file mode 100644 index 000000000000..4421e9771b8a --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/brcm,iproc-mhb.txt @@ -0,0 +1,18 @@ +Broadcom iProc Multi Host Bridge (MHB) + +Certain Broadcom iProc SoCs have a multi host bridge (MHB) block that controls +the connection and configuration of 1) internal PCIe serdes; 2) PCIe endpoint +interface; 3) access to the Nitro (network processing) engine + +This node allows access to these MHB registers via syscon. + +Required properties: +- compatible: should contain: + "brcm,sr-mhb", "syscon" for Stingray +- reg: base address and range of the MHB registers + +Example: + mhb: syscon@60401000 { + compatible = "brcm,sr-mhb", "syscon"; + reg = <0 0x60401000 0 0x38c>; + }; diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index 6a1ae3a2b77f..e6754974a745 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -127,6 +127,12 @@ Required properties for the LED child node: Optional properties for the LED child node: - label : see Documentation/devicetree/bindings/leds/common.txt +Optional nodes: +- max77693-muic : + Node used only by extcon consumers. + Required properties: + - compatible : "maxim,max77693-muic" + Example: #include <dt-bindings/leds/common.h> diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt index 39ba4146769d..ac235fe385fc 100644 --- a/Documentation/devicetree/bindings/mfd/mc13xxx.txt +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -113,7 +113,6 @@ MC13892 regulators: Examples: ecspi@70010000 { /* ECSPI1 */ - fsl,spi-num-chipselects = <2>; cs-gpios = <&gpio4 24 0>, /* GPIO4_24 */ <&gpio4 25 0>; /* GPIO4_25 */ diff --git a/Documentation/devicetree/bindings/mfd/sprd,sc27xx-pmic.txt b/Documentation/devicetree/bindings/mfd/sprd,sc27xx-pmic.txt new file mode 100644 index 000000000000..21b9a897fca5 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/sprd,sc27xx-pmic.txt @@ -0,0 +1,40 @@ +Spreadtrum SC27xx Power Management Integrated Circuit (PMIC) + +The Spreadtrum SC27xx series PMICs contain SC2720, SC2721, SC2723, SC2730 +and SC2731. The Spreadtrum PMIC belonging to SC27xx series integrates all +mobile handset power management, audio codec, battery management and user +interface support function in a single chip. It has 6 major functional +blocks: +- DCDCs to support CPU, memory. +- LDOs to support both internal and external requirement. +- Battery management system, such as charger, fuel gauge. +- Audio codec. +- User interface function, such as indicator, flash LED and so on. +- IC level interface, such as power on/off control, RTC and typec and so on. + +Required properties: +- compatible: Should be one of the following: + "sprd,sc2720" + "sprd,sc2721" + "sprd,sc2723" + "sprd,sc2730" + "sprd,sc2731" +- reg: The address of the device chip select, should be 0. +- spi-max-frequency: Typically set to 26000000. +- interrupts: The interrupt line the device is connected to. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: The number of cells to describe an PMIC IRQ, must be 2. +- #address-cells: Child device offset number of cells, must be 1. +- #size-cells: Child device size number of cells, must be 0. + +Example: +pmic@0 { + compatible = "sprd,sc2731"; + reg = <0>; + spi-max-frequency = <26000000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/mips/brcm/soc.txt b/Documentation/devicetree/bindings/mips/brcm/soc.txt index e4e1cd91fb1f..356c29789cf5 100644 --- a/Documentation/devicetree/bindings/mips/brcm/soc.txt +++ b/Documentation/devicetree/bindings/mips/brcm/soc.txt @@ -11,3 +11,156 @@ Required properties: The experimental -viper variants are for running Linux on the 3384's BMIPS4355 cable modem CPU instead of the BMIPS5000 application processor. + +Power management +---------------- + +For power management (particularly, S2/S3/S5 system suspend), the following SoC +components are needed: + += Always-On control block (AON CTRL) + +This hardware provides control registers for the "always-on" (even in low-power +modes) hardware, such as the Power Management State Machine (PMSM). + +Required properties: +- compatible : should be one of + "brcm,bcm7425-aon-ctrl" + "brcm,bcm7429-aon-ctrl" + "brcm,bcm7435-aon-ctrl" and + "brcm,brcmstb-aon-ctrl" +- reg : the register start and length for the AON CTRL block + +Example: + +syscon@410000 { + compatible = "brcm,bcm7425-aon-ctrl", "brcm,brcmstb-aon-ctrl"; + reg = <0x410000 0x400>; +}; + += Memory controllers + +A Broadcom STB SoC typically has a number of independent memory controllers, +each of which may have several associated hardware blocks, which are versioned +independently (control registers, DDR PHYs, etc.). One might consider +describing these controllers as a parent "memory controllers" block, which +contains N sub-nodes (one for each controller in the system), each of which is +associated with a number of hardware register resources (e.g., its PHY. + +== MEMC (MEMory Controller) + +Represents a single memory controller instance. + +Required properties: +- compatible : should contain "brcm,brcmstb-memc" and "simple-bus" +- ranges : should contain the child address in the parent address + space, must be 0 here, and the register start and length of + the entire memory controller (including all sub nodes: DDR PHY, + arbiter, etc.) +- #address-cells : must be 1 +- #size-cells : must be 1 + +Example: + + memory-controller@0 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges = <0x0 0x0 0xa000>; + #address-cells = <1>; + #size-cells = <1>; + + memc-arb@1000 { + ... + }; + + memc-ddr@2000 { + ... + }; + + ddr-phy@6000 { + ... + }; + }; + +Should contain subnodes for any of the following relevant hardware resources: + +== DDR PHY control + +Control registers for this memory controller's DDR PHY. + +Required properties: +- compatible : should contain one of these + "brcm,brcmstb-ddr-phy-v64.5" + "brcm,brcmstb-ddr-phy" + +- reg : the DDR PHY register range and length + +Example: + + ddr-phy@6000 { + compatible = "brcm,brcmstb-ddr-phy-v64.5"; + reg = <0x6000 0xc8>; + }; + +== DDR memory controller sequencer + +Control registers for this memory controller's DDR memory sequencer + +Required properties: +- compatible : should contain one of these + "brcm,bcm7425-memc-ddr" + "brcm,bcm7429-memc-ddr" + "brcm,bcm7435-memc-ddr" and + "brcm,brcmstb-memc-ddr" + +- reg : the DDR sequencer register range and length + +Example: + + memc-ddr@2000 { + compatible = "brcm,bcm7425-memc-ddr", "brcm,brcmstb-memc-ddr"; + reg = <0x2000 0x300>; + }; + +== MEMC Arbiter + +The memory controller arbiter is responsible for memory clients allocation +(bandwidth, priorities etc.) and needs to have its contents restored during +deep sleep states (S3). + +Required properties: + +- compatible : should contain one of these + "brcm,brcmstb-memc-arb-v10.0.0.0" + "brcm,brcmstb-memc-arb" + +- reg : the DDR Arbiter register range and length + +Example: + + memc-arb@1000 { + compatible = "brcm,brcmstb-memc-arb-v10.0.0.0"; + reg = <0x1000 0x248>; + }; + +== Timers + +The Broadcom STB chips contain a timer block with several general purpose +timers that can be used. + +Required properties: + +- compatible : should contain one of: + "brcm,bcm7425-timers" + "brcm,bcm7429-timers" + "brcm,bcm7435-timers and + "brcm,brcmstb-timers" +- reg : the timers register range +- interrupts : the interrupt line for this timer block + +Example: + + timers: timer@4067c0 { + compatible = "brcm,bcm7425-timers", "brcm,brcmstb-timers"; + reg = <0x4067c0 0x40>; + interrupts = <&periph_intc 19>; + }; diff --git a/Documentation/devicetree/bindings/misc/ge-achc.txt b/Documentation/devicetree/bindings/misc/ge-achc.txt new file mode 100644 index 000000000000..77df94d7a32f --- /dev/null +++ b/Documentation/devicetree/bindings/misc/ge-achc.txt @@ -0,0 +1,26 @@ +* GE Healthcare USB Management Controller + +A device which handles data aquisition from compatible USB based peripherals. +SPI is used for device management. + +Note: This device does not expose the peripherals as USB devices. + +Required properties: + +- compatible : Should be "ge,achc" + +Required SPI properties: + +- reg : Should be address of the device chip select within + the controller. + +- spi-max-frequency : Maximum SPI clocking speed of device in Hz, should be + 1MHz for the GE ACHC. + +Example: + +spidev0: spi@0 { + compatible = "ge,achc"; + reg = <0>; + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index 9ce35af8507c..4cab5d85cf6f 100644 --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -13,6 +13,7 @@ Required properties: at25df321a at25df641 at26df081a + en25s64 mr25h256 mr25h10 mr25h40 @@ -31,6 +32,7 @@ Required properties: s25fl008k s25fl064k sst25vf040b + sst25wf040b m25p40 m25p80 m25p16 diff --git a/Documentation/devicetree/bindings/net/bluetooth.txt b/Documentation/devicetree/bindings/net/bluetooth.txt new file mode 100644 index 000000000000..94797df751b8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/bluetooth.txt @@ -0,0 +1,5 @@ +The following properties are common to the Bluetooth controllers: + +- local-bd-address: array of 6 bytes, specifies the BD address that was + uniquely assigned to the Bluetooth device, formatted with least significant + byte first (little-endian). diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt index 4448d063ddf6..464d6bf87605 100644 --- a/Documentation/devicetree/bindings/net/dsa/lan9303.txt +++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt @@ -52,7 +52,7 @@ I2C managed mode: port@1 { /* external port 1 */ reg = <1>; - label = "lan1; + label = "lan1"; }; port@2 { /* external port 2 */ @@ -89,7 +89,7 @@ MDIO managed mode: port@1 { /* external port 1 */ reg = <1>; - label = "lan1; + label = "lan1"; }; port@2 { /* external port 2 */ diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt new file mode 100644 index 000000000000..3d6d5fa0c4d5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt @@ -0,0 +1,207 @@ +* Allwinner sun8i GMAC ethernet controller + +This device is a platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +Required properties: +- compatible: must be one of the following string: + "allwinner,sun8i-a83t-emac" + "allwinner,sun8i-h3-emac" + "allwinner,sun8i-v3s-emac" + "allwinner,sun50i-a64-emac" +- reg: address and length of the register for the device. +- interrupts: interrupt for the device +- interrupt-names: must be "macirq" +- clocks: A phandle to the reference clock for this device +- clock-names: must be "stmmaceth" +- resets: A phandle to the reset control for this device +- reset-names: must be "stmmaceth" +- phy-mode: See ethernet.txt +- phy-handle: See ethernet.txt +- #address-cells: shall be 1 +- #size-cells: shall be 0 +- syscon: A phandle to the syscon of the SoC with one of the following + compatible string: + - allwinner,sun8i-h3-system-controller + - allwinner,sun8i-v3s-system-controller + - allwinner,sun50i-a64-system-controller + - allwinner,sun8i-a83t-system-controller + +Optional properties: +- allwinner,tx-delay-ps: TX clock delay chain value in ps. Range value is 0-700. Default is 0) +- allwinner,rx-delay-ps: RX clock delay chain value in ps. Range value is 0-3100. Default is 0) +Both delay properties need to be a multiple of 100. They control the delay for +external PHY. + +Optional properties for the following compatibles: + - "allwinner,sun8i-h3-emac", + - "allwinner,sun8i-v3s-emac": +- allwinner,leds-active-low: EPHY LEDs are active low + +Required child node of emac: +- mdio bus node: should be named mdio with compatible "snps,dwmac-mdio" + +Required properties of the mdio node: +- #address-cells: shall be 1 +- #size-cells: shall be 0 + +The device node referenced by "phy" or "phy-handle" must be a child node +of the mdio node. See phy.txt for the generic PHY bindings. + +The following compatibles require that the emac node have a mdio-mux child +node called "mdio-mux": + - "allwinner,sun8i-h3-emac" + - "allwinner,sun8i-v3s-emac": +Required properties for the mdio-mux node: + - compatible = "allwinner,sun8i-h3-mdio-mux" + - mdio-parent-bus: a phandle to EMAC mdio + - one child mdio for the integrated mdio with the compatible + "allwinner,sun8i-h3-mdio-internal" + - one child mdio for the external mdio if present (V3s have none) +Required properties for the mdio-mux children node: + - reg: 1 for internal MDIO bus, 2 for external MDIO bus + +The following compatibles require a PHY node representing the integrated +PHY, under the integrated MDIO bus node if an mdio-mux node is used: + - "allwinner,sun8i-h3-emac", + - "allwinner,sun8i-v3s-emac": + +Additional information regarding generic multiplexer properties can be found +at Documentation/devicetree/bindings/net/mdio-mux.txt + +Required properties of the integrated phy node: +- clocks: a phandle to the reference clock for the EPHY +- resets: a phandle to the reset control for the EPHY +- Must be a child of the integrated mdio + +Example with integrated PHY: +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "mdio-mux", "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + + mdio-parent-bus = <&mdio>; + + int_mdio: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + int_mii_phy: ethernet-phy@1 { + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + phy-is-integrated; + }; + }; + ext_mdio: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; + +Example with external PHY: +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + allwinner,leds-active-low; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + + mdio-parent-bus = <&mdio>; + + int_mdio: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + int_mii_phy: ethernet-phy@1 { + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + }; + }; + ext_mdio: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + ext_rgmii_phy: ethernet-phy@1 { + reg = <1>; + }; + }: + }; +}; + +Example with SoC without integrated PHY + +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-a83t-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + + mdio: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + ext_rgmii_phy: ethernet-phy@1 { + reg = <1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index 6f55bdd52f8a..f0dc94409107 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -34,6 +34,19 @@ Optional properties: - fsl,err006687-workaround-present: If present indicates that the system has the hardware workaround for ERR006687 applied and does not need a software workaround. + -interrupt-names: names of the interrupts listed in interrupts property in + the same order. The defaults if not specified are + __Number of interrupts__ __Default__ + 1 "int0" + 2 "int0", "pps" + 3 "int0", "int1", "int2" + 4 "int0", "int1", "int2", "pps" + The order may be changed as long as they correspond to the interrupts + property. Currently, only i.mx7 uses "int1" and "int2". They correspond to + tx/rx queues 1 and 2. "int0" will be used for queue 0 and ENET_MII interrupts. + For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse + per second interrupt associated with 1588 precision time protocol(PTP). + Optional subnodes: - mdio : specifies the mdio bus in the FEC, used as a container for phy nodes diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index 16723535e1aa..c902261893b9 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -17,6 +17,8 @@ Required properties: - "renesas,etheravb-r8a7795" for the R8A7795 SoC. - "renesas,etheravb-r8a7796" for the R8A7796 SoC. + - "renesas,etheravb-r8a77970" for the R8A77970 SoC. + - "renesas,etheravb-r8a77995" for the R8A77995 SoC. - "renesas,etheravb-rcar-gen3" as a fallback for the above R-Car Gen3 devices. @@ -40,7 +42,7 @@ Optional properties: - interrupt-parent: the phandle for the interrupt controller that services interrupts for this device. - interrupt-names: A list of interrupt names. - For the R8A779[56] SoCs this property is mandatory; + For the R-Car Gen 3 SoCs this property is mandatory; it should include one entry per channel, named "ch%u", where %u is the channel number ranging from 0 to 24. For other SoCs this property is optional; if present diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt index 0115c85a2425..5172799a7f1a 100644 --- a/Documentation/devicetree/bindings/net/sh_eth.txt +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -4,7 +4,8 @@ This file provides information on what the device node for the SH EtherMAC interface contains. Required properties: -- compatible: "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC. +- compatible: Must contain one or more of the following: + "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC. "renesas,ether-r8a7743" if the device is a part of R8A7743 SoC. "renesas,ether-r8a7745" if the device is a part of R8A7745 SoC. "renesas,ether-r8a7778" if the device is a part of R8A7778 SoC. @@ -14,6 +15,14 @@ Required properties: "renesas,ether-r8a7793" if the device is a part of R8A7793 SoC. "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. + "renesas,rcar-gen1-ether" for a generic R-Car Gen1 device. + "renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1 + device. + + When compatible with the generic version, nodes must list + the SoC-specific version corresponding to the platform + first followed by the generic version. + - reg: offset and length of (1) the E-DMAC/feLic register block (required), (2) the TSU register block (optional). - interrupts: interrupt specifier for the sole interrupt. @@ -36,7 +45,8 @@ Optional properties: Example (Lager board): ethernet@ee700000 { - compatible = "renesas,ether-r8a7790"; + compatible = "renesas,ether-r8a7790", + "renesas,rcar-gen2-ether"; reg = <0 0xee700000 0 0x400>; interrupt-parent = <&gic>; interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index c3a7be6615c5..3a28a5d8857d 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -12,7 +12,7 @@ Required properties: Valid interrupt names are: - "macirq" (combined signal for various interrupt events) - "eth_wake_irq" (the interrupt to manage the remote wake-up packet detection) - - "eth_lpi" (the interrupt that occurs when Tx or Rx enters/exits LPI state) + - "eth_lpi" (the interrupt that occurs when Rx exits the LPI state) - phy-mode: See ethernet.txt file in the same directory. - snps,reset-gpio gpio number for phy reset. - snps,reset-active-low boolean flag to indicate if phy reset is active low. diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt index 081c49c0dac0..d69543701d5d 100644 --- a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt +++ b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt @@ -5,6 +5,7 @@ Required properties: "allwinner,sun4i-a10-sid" "allwinner,sun7i-a20-sid" "allwinner,sun8i-h3-sid" + "allwinner,sun50i-a64-sid" - reg: Should contain registers location and length diff --git a/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt b/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt index fafd85bd67a6..e3298e18de26 100644 --- a/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt +++ b/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt @@ -1,4 +1,4 @@ -= Amlogic eFuse device tree bindings = += Amlogic Meson GX eFuse device tree bindings = Required properties: - compatible: should be "amlogic,meson-gxbb-efuse" diff --git a/Documentation/devicetree/bindings/nvmem/amlogic-meson-mx-efuse.txt b/Documentation/devicetree/bindings/nvmem/amlogic-meson-mx-efuse.txt new file mode 100644 index 000000000000..a3c63954a1a4 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/amlogic-meson-mx-efuse.txt @@ -0,0 +1,22 @@ +Amlogic Meson6/Meson8/Meson8b efuse + +Required Properties: +- compatible: depending on the SoC this should be one of: + - "amlogic,meson6-efuse" + - "amlogic,meson8-efuse" + - "amlogic,meson8b-efuse" +- reg: base address and size of the efuse registers +- clocks: a reference to the efuse core gate clock +- clock-names: must be "core" + +All properties and sub-nodes as well as the consumer bindings +defined in nvmem.txt in this directory are also supported. + + +Example: + efuse: nvmem@0 { + compatible = "amlogic,meson8-efuse"; + reg = <0x0 0x2000>; + clocks = <&clkc CLKID_EFUSE>; + clock-names = "core"; + }; diff --git a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt index 1ff02afdc55a..60bec4782806 100644 --- a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt +++ b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt @@ -6,6 +6,7 @@ Required properties: - "rockchip,rk3188-efuse" - for RK3188 SoCs. - "rockchip,rk3228-efuse" - for RK3228 SoCs. - "rockchip,rk3288-efuse" - for RK3288 SoCs. + - "rockchip,rk3368-efuse" - for RK3368 SoCs. - "rockchip,rk3399-efuse" - for RK3399 SoCs. - reg: Should contain the registers location and exact eFuse size - clocks: Should be the clock id of eFuse diff --git a/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt b/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt new file mode 100644 index 000000000000..20bc49b49799 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt @@ -0,0 +1,20 @@ +Device tree bindings for Low Power General Purpose Register found in i.MX6Q/D +Secure Non-Volatile Storage. + +This DT node should be represented as a sub-node of a "syscon", +"simple-mfd" node. + +Required properties: +- compatible: should be one of the fallowing variants: + "fsl,imx6q-snvs-lpgpr" for Freescale i.MX6Q/D/DL/S + "fsl,imx6ul-snvs-lpgpr" for Freescale i.MX6UL + +Example: +snvs: snvs@020cc000 { + compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd"; + reg = <0x020cc000 0x4000>; + + snvs_lpgpr: snvs-lpgpr { + compatible = "fsl,imx6q-snvs-lpgpr"; + }; +}; diff --git a/Documentation/devicetree/bindings/nvmem/uniphier-efuse.txt b/Documentation/devicetree/bindings/nvmem/uniphier-efuse.txt new file mode 100644 index 000000000000..eccf490d5a6d --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/uniphier-efuse.txt @@ -0,0 +1,49 @@ += UniPhier eFuse device tree bindings = + +This UniPhier eFuse must be under soc-glue. + +Required properties: +- compatible: should be "socionext,uniphier-efuse" +- reg: should contain the register location and length + += Data cells = +Are child nodes of efuse, bindings of which as described in +bindings/nvmem/nvmem.txt + +Example: + + soc-glue@5f900000 { + compatible = "socionext,uniphier-ld20-soc-glue-debug", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x5f900000 0x2000>; + + efuse@100 { + compatible = "socionext,uniphier-efuse"; + reg = <0x100 0x28>; + }; + + efuse@200 { + compatible = "socionext,uniphier-efuse"; + reg = <0x200 0x68>; + #address-cells = <1>; + #size-cells = <1>; + + /* Data cells */ + usb_mon: usb-mon@54 { + reg = <0x54 0xc>; + }; + }; + }; + += Data consumers = +Are device nodes which consume nvmem data cells. + +Example: + + usb { + ... + nvmem-cells = <&usb_mon>; + nvmem-cell-names = "usb_mon"; + } diff --git a/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt b/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt new file mode 100644 index 000000000000..515b2f9542e5 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt @@ -0,0 +1,42 @@ +* Synopsys DesignWare PCIe root complex in ECAM shift mode + +In some cases, firmware may already have configured the Synopsys DesignWare +PCIe controller in RC mode with static ATU window mappings that cover all +config, MMIO and I/O spaces in a [mostly] ECAM compatible fashion. +In this case, there is no need for the OS to perform any low level setup +of clocks, PHYs or device registers, nor is there any reason for the driver +to reconfigure ATU windows for config and/or IO space accesses at runtime. + +In cases where the IP was synthesized with a minimum ATU window size of +64 KB, it cannot be supported by the generic ECAM driver, because it +requires special config space accessors that filter accesses to device #1 +and beyond on the first bus. + +Required properties: +- compatible: "marvell,armada8k-pcie-ecam" or + "socionext,synquacer-pcie-ecam" or + "snps,dw-pcie-ecam" (must be preceded by a more specific match) + +Please refer to the binding document of "pci-host-ecam-generic" in the +file host-generic-pci.txt for a description of the remaining required +and optional properties. + +Example: + + pcie1: pcie@7f000000 { + compatible = "socionext,synquacer-pcie-ecam", "snps,dw-pcie-ecam"; + device_type = "pci"; + reg = <0x0 0x7f000000 0x0 0xf00000>; + bus-range = <0x0 0xe>; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x1000000 0x00 0x00010000 0x00 0x7ff00000 0x0 0x00010000>, + <0x2000000 0x00 0x70000000 0x00 0x70000000 0x0 0x0f000000>, + <0x3000000 0x3f 0x00000000 0x3f 0x00000000 0x1 0x00000000>; + + #interrupt-cells = <0x1>; + interrupt-map-mask = <0x0 0x0 0x0 0x0>; + interrupt-map = <0x0 0x0 0x0 0x0 &gic 0x0 0x0 0x0 182 0x4>; + msi-map = <0x0 &its 0x0 0x10000>; + dma-coherent; + }; diff --git a/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt new file mode 100644 index 000000000000..c84bc027930b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt @@ -0,0 +1,68 @@ +HiSilicon STB PCIe host bridge DT description + +The HiSilicon STB PCIe host controller is based on the DesignWare PCIe core. +It shares common functions with the DesignWare PCIe core driver and inherits +common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Additional properties are described here: + +Required properties +- compatible: Should be one of the following strings: + "hisilicon,hi3798cv200-pcie" +- reg: Should contain sysctl, rc_dbi, config registers location and length. +- reg-names: Must include the following entries: + "control": control registers of PCIe controller; + "rc-dbi": configuration space of PCIe controller; + "config": configuration transaction space of PCIe controller. +- bus-range: PCI bus numbers covered. +- interrupts: MSI interrupt. +- interrupt-names: Must include "msi" entries. +- clocks: List of phandle and clock specifier pairs as listed in clock-names + property. +- clock-name: Must include the following entries: + "aux": auxiliary gate clock; + "pipe": pipe gate clock; + "sys": sys gate clock; + "bus": bus gate clock. +- resets: List of phandle and reset specifier pairs as listed in reset-names + property. +- reset-names: Must include the following entries: + "soft": soft reset; + "sys": sys reset; + "bus": bus reset. + +Optional properties: +- reset-gpios: The gpio to generate PCIe PERST# assert and deassert signal. +- phys: List of phandle and phy mode specifier, should be 0. +- phy-names: Must be "phy". + +Example: + pcie@f9860000 { + compatible = "hisilicon,hi3798cv200-pcie"; + reg = <0xf9860000 0x1000>, + <0xf0000000 0x2000>, + <0xf2000000 0x01000000>; + reg-names = "control", "rc-dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0 15>; + num-lanes = <1>; + ranges=<0x81000000 0 0 0xf4000000 0 0x00010000 + 0x82000000 0 0xf3000000 0xf3000000 0 0x01000000>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg PCIE_AUX_CLK>, + <&crg PCIE_PIPE_CLK>, + <&crg PCIE_SYS_CLK>, + <&crg PCIE_BUS_CLK>; + clock-names = "aux", "pipe", "sys", "bus"; + resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>; + reset-names = "soft", "sys", "bus"; + phys = <&combphy1 PHY_TYPE_PCIE>; + phy-names = "phy"; + }; diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index c0484da0f20d..66df1e81e0b8 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -18,6 +18,7 @@ Required properties: "fsl,ls2088a-pcie" "fsl,ls1088a-pcie" "fsl,ls1046a-pcie" + "fsl,ls1012a-pcie" - reg: base addresses and lengths of the PCIe controller register blocks. - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 1b4d2803dad1..145a4f04194f 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -1,10 +1,15 @@ NVIDIA Tegra PCIe controller Required properties: -- compatible: For Tegra20, must contain "nvidia,tegra20-pcie". For Tegra30, - "nvidia,tegra30-pcie". For Tegra124, must contain "nvidia,tegra124-pcie". - Otherwise, must contain "nvidia,<chip>-pcie", plus one of the above, where - <chip> is tegra132 or tegra210. +- compatible: Must be: + - "nvidia,tegra20-pcie": for Tegra20 + - "nvidia,tegra30-pcie": for Tegra30 + - "nvidia,tegra124-pcie": for Tegra124 and Tegra132 + - "nvidia,tegra210-pcie": for Tegra210 + - "nvidia,tegra186-pcie": for Tegra186 +- power-domains: To ungate power partition by BPMP powergate driver. Must + contain BPMP phandle and PCIe power partition ID. This is required only + for Tegra186. - device_type: Must be "pci" - reg: A list of physical base address and length for each set of controller registers. Must contain an entry for each entry in the reg-names property. @@ -124,6 +129,16 @@ Power supplies for Tegra210: - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must supply 1.8 V. +Power supplies for Tegra186: +- Required: + - dvdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - hvdd-pex-pll-supply: High-voltage supply for PLLE (shared with USB3). Must + supply 1.8 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 1.8 V. + - vddio-pexctl-aud-supply: Power supply for PCIe side band signals. Must + supply 1.8 V. + Root ports are defined as subnodes of the PCIe controller node. Required properties: @@ -546,3 +561,114 @@ Board DTS: status = "okay"; }; }; + +Tegra186: +--------- + +SoC DTSI: + + pcie@10003000 { + compatible = "nvidia,tegra186-pcie"; + power-domains = <&bpmp TEGRA186_POWER_DOMAIN_PCX>; + device_type = "pci"; + reg = <0x0 0x10003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x10003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x40000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x10000000 0x0 0x10000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x10001000 0x0 0x10001000 0 0x00001000 /* port 1 configuration space */ + 0x82000000 0 0x10004000 0x0 0x10004000 0 0x00001000 /* port 2 configuration space */ + 0x81000000 0 0x0 0x0 0x50000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x50100000 0x0 0x50100000 0 0x07F00000 /* non-prefetchable memory (127 MiB) */ + 0xc2000000 0 0x58000000 0x0 0x58000000 0 0x28000000>; /* prefetchable memory (640 MiB) */ + + clocks = <&bpmp TEGRA186_CLK_AFI>, + <&bpmp TEGRA186_CLK_PCIE>, + <&bpmp TEGRA186_CLK_PLLE>; + clock-names = "afi", "pex", "pll_e"; + + resets = <&bpmp TEGRA186_RESET_AFI>, + <&bpmp TEGRA186_RESET_PCIE>, + <&bpmp TEGRA186_RESET_PCIEXCLK>; + reset-names = "afi", "pex", "pcie_x"; + + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x10000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x10001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + + pci@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x10004000 0 0x1000>; + reg = <0x001800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie@10003000 { + status = "okay"; + + dvdd-pex-supply = <&vdd_pex>; + hvdd-pex-pll-supply = <&vdd_1v8>; + hvdd-pex-supply = <&vdd_1v8>; + vddio-pexctl-aud-supply = <&vdd_1v8>; + + pci@1,0 { + nvidia,num-lanes = <4>; + status = "okay"; + }; + + pci@2,0 { + nvidia,num-lanes = <0>; + status = "disabled"; + }; + + pci@3,0 { + nvidia,num-lanes = <1>; + status = "disabled"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index 3d038638612b..9fe7e12a7bf3 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -60,17 +60,15 @@ Example SoC configuration: 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; - pci@0,1 { + usb@1,0 { reg = <0x800 0 0 0 0>; - device_type = "pci"; - phys = <&usbphy 0 0>; + phys = <&usb0 0>; phy-names = "usb"; }; - pci@0,2 { + usb@2,0 { reg = <0x1000 0 0 0 0>; - device_type = "pci"; - phys = <&usbphy 0 0>; + phys = <&usb0 0>; phy-names = "usb"; }; }; diff --git a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt index 30b364e504ba..11063293f761 100644 --- a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt +++ b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt @@ -2,14 +2,75 @@ V3 Semiconductor V360 EPC PCI bridge This bridge is found in the ARM Integrator/AP (Application Platform) -Integrator-specific notes: +Required properties: +- compatible: should be one of: + "v3,v360epc-pci" + "arm,integrator-ap-pci", "v3,v360epc-pci" +- reg: should contain two register areas: + first the base address of the V3 host bridge controller, 64KB + second the configuration area register space, 16MB +- interrupts: should contain a reference to the V3 error interrupt + as routed on the system. +- bus-range: see pci.txt +- ranges: this follows the standard PCI bindings in the IEEE Std + 1275-1994 (see pci.txt) with the following restriction: + - The non-prefetchable and prefetchable memory windows must + each be exactly 256MB (0x10000000) in size. + - The prefetchable memory window must be immediately adjacent + to the non-prefetcable memory window +- dma-ranges: three ranges for the inbound memory region. The ranges must + be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, + 64MB, 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked + as pre-fetchable. Two ranges are supported by the hardware. -- syscon: should contain a link to the syscon device node (since +Integrator-specific required properties: +- syscon: should contain a link to the syscon device node, since on the Integrator, some registers in the syscon are required to - operate the V3). + operate the V3 host bridge. -V360 EPC specific notes: +Example: -- reg: should contain the base address of the V3 adapter. -- interrupts: should contain a reference to the V3 error interrupt - as routed on the system. +pci: pciv3@62000000 { + compatible = "arm,integrator-ap-pci", "v3,v360epc-pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0x62000000 0x10000>, <0x61000000 0x01000000>; + interrupt-parent = <&pic>; + interrupts = <17>; /* Bus error IRQ */ + clocks = <&pciclk>; + bus-range = <0x00 0xff>; + ranges = 0x01000000 0 0x00000000 /* I/O space @00000000 */ + 0x60000000 0 0x01000000 /* 16 MiB @ LB 60000000 */ + 0x02000000 0 0x40000000 /* non-prefectable memory @40000000 */ + 0x40000000 0 0x10000000 /* 256 MiB @ LB 40000000 1:1 */ + 0x42000000 0 0x50000000 /* prefetchable memory @50000000 */ + 0x50000000 0 0x10000000>; /* 256 MiB @ LB 50000000 1:1 */ + dma-ranges = <0x02000000 0 0x20000000 /* EBI memory space */ + 0x20000000 0 0x20000000 /* 512 MB @ LB 20000000 1:1 */ + 0x02000000 0 0x80000000 /* Core module alias memory */ + 0x80000000 0 0x40000000>; /* 1GB @ LB 80000000 */ + interrupt-map-mask = <0xf800 0 0 0x7>; + interrupt-map = < + /* IDSEL 9 */ + 0x4800 0 0 1 &pic 13 /* INT A on slot 9 is irq 13 */ + 0x4800 0 0 2 &pic 14 /* INT B on slot 9 is irq 14 */ + 0x4800 0 0 3 &pic 15 /* INT C on slot 9 is irq 15 */ + 0x4800 0 0 4 &pic 16 /* INT D on slot 9 is irq 16 */ + /* IDSEL 10 */ + 0x5000 0 0 1 &pic 14 /* INT A on slot 10 is irq 14 */ + 0x5000 0 0 2 &pic 15 /* INT B on slot 10 is irq 15 */ + 0x5000 0 0 3 &pic 16 /* INT C on slot 10 is irq 16 */ + 0x5000 0 0 4 &pic 13 /* INT D on slot 10 is irq 13 */ + /* IDSEL 11 */ + 0x5800 0 0 1 &pic 15 /* INT A on slot 11 is irq 15 */ + 0x5800 0 0 2 &pic 16 /* INT B on slot 11 is irq 16 */ + 0x5800 0 0 3 &pic 13 /* INT C on slot 11 is irq 13 */ + 0x5800 0 0 4 &pic 14 /* INT D on slot 11 is irq 14 */ + /* IDSEL 12 */ + 0x6000 0 0 1 &pic 16 /* INT A on slot 12 is irq 16 */ + 0x6000 0 0 2 &pic 13 /* INT B on slot 12 is irq 13 */ + 0x6000 0 0 3 &pic 14 /* INT C on slot 12 is irq 14 */ + 0x6000 0 0 4 &pic 15 /* INT D on slot 12 is irq 15 */ + >; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt index 61466c58faae..d857b67fab72 100644 --- a/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/cortina,gemini-pinctrl.txt @@ -9,8 +9,14 @@ The pin controller node must be a subnode of the system controller node. Required properties: - compatible: "cortina,gemini-pinctrl" -Subnodes of the pin controller contain pin control multiplexing set-up. -Please refer to pinctrl-bindings.txt for generic pin multiplexing nodes. +Subnodes of the pin controller contain pin control multiplexing set-up +and pin configuration of individual pins. + +Please refer to pinctrl-bindings.txt for generic pin multiplexing nodes +and generic pin config nodes. + +Supported configurations: +- skew-delay is supported on the Ethernet pins Example: diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt index f64060908d5a..c7c088d2dd50 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt @@ -97,8 +97,8 @@ group spi_quad - pins 15-16 - functions spi, gpio -group uart_2 - - pins 9-10 +group uart2 + - pins 9-10 and 18-19 - functions uart, gpio Available groups and functions for the South bridge: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index 4483cc31e531..ad9bbbba36e9 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -271,6 +271,10 @@ output-high - set the pin to output mode with high level sleep-hardware-state - indicate this is sleep related state which will be programmed into the registers for the sleep state. slew-rate - set the slew rate +skew-delay - this affects the expected clock skew on input pins + and the delay before latching a value to an output + pin. Typically indicates how many double-inverters are + used to delay the signal. For example: diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt index c934106b10aa..9c451c20dda4 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt @@ -13,6 +13,7 @@ Required properties: - "microchip,mcp23s18" for 16 GPIO SPI version - "microchip,mcp23008" for 8 GPIO I2C version or - "microchip,mcp23017" for 16 GPIO I2C version of the chip + - "microchip,mcp23018" for 16 GPIO I2C version NOTE: Do not use the old mcp prefix any more. It is deprecated and will be removed. - #gpio-cells : Should be two. @@ -81,3 +82,61 @@ gpiom1: gpio@0 { reg = <0>; spi-max-frequency = <1000000>; }; + +Pull-up configuration +===================== + +If pins are used as output, they can also be configured with pull-ups. This is +done with pinctrl. + +Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt> +for details of the common pinctrl bindings used by client devices, +including the meaning of the phrase "pin configuration node". + +Optional Pinmux properties: +-------------------------- +Following properties are required if default setting of pins are required +at boot. +- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per + <pinctrl-binding.txt>. + +The pin configurations are defined as child of the pinctrl states node. Each +sub-node have following properties: + +Required properties: +------------------ +- pins: List of pins. Valid values of pins properties are: + gpio0 ... gpio7 for the devices with 8 GPIO pins and + gpio0 ... gpio15 for the devices with 16 GPIO pins. + +Optional properties: +------------------- +The following optional property is defined in the pinmux DT binding document +<pinctrl-bindings.txt>. Absence of this property will leave the configuration +in its default state. + bias-pull-up + +Example with pinctrl to pull-up output pins: +gpio21: gpio@21 { + compatible = "microchip,mcp23017"; + gpio-controller; + #gpio-cells = <0x2>; + reg = <0x21>; + interrupt-parent = <&socgpio>; + interrupts = <0x17 0x8>; + interrupt-names = "mcp23017@21 irq"; + interrupt-controller; + #interrupt-cells = <0x2>; + microchip,irq-mirror; + pinctrl-names = "default"; + pinctrl-0 = <&i2cgpio0irq &gpio21pullups>; + + gpio21pullups: pinmux { + pins = "gpio0", "gpio1", "gpio2", "gpio3", + "gpio4", "gpio5", "gpio6", "gpio7", + "gpio8", "gpio9", "gpio10", "gpio11", + "gpio12", "gpio13", "gpio14", "gpio15"; + bias-pull-up; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index 5b12c57e7f02..5c25fcb29fb5 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -15,6 +15,7 @@ PMIC's from Qualcomm. "qcom,pm8921-gpio" "qcom,pm8941-gpio" "qcom,pm8994-gpio" + "qcom,pmi8994-gpio" "qcom,pma8084-gpio" "qcom,pmi8994-gpio" @@ -85,6 +86,7 @@ to specify in a pin configuration subnode: gpio1-gpio44 for pm8921 gpio1-gpio36 for pm8941 gpio1-gpio22 for pm8994 + gpio1-gpio10 for pmi8994 gpio1-gpio22 for pma8084 gpio1-gpio10 for pmi8994 diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt index 43e21474528a..fd3696eb36bf 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-pinctrl.txt @@ -12,8 +12,10 @@ Pin controller node ------------------- Required properties: - - compatible - this shall be "renesas,r7s72100-ports". + - compatible: should be: + - "renesas,r7s72100-ports": for RZ/A1H + - "renesas,r7s72101-ports", "renesas,r7s72100-ports": for RZ/A1M + - "renesas,r7s72102-ports": for RZ/A1L - reg address base and length of the memory area where the pin controller diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt index 33e3d3c47552..58c2a4c229db 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -143,6 +143,24 @@ Required properties: * 16 : Alternate Function 15 * 17 : Analog + To simplify the usage, macro is available to generate "pinmux" field. + This macro is available here: + - include/dt-bindings/pinctrl/stm32-pinfunc.h + + Some examples of using macro: + /* GPIO A9 set as alernate function 2 */ + ... { + pinmux = <STM32_PINMUX('A', 9, AF2)>; + }; + /* GPIO A9 set as GPIO */ + ... { + pinmux = <STM32_PINMUX('A', 9, GPIO)>; + }; + /* GPIO A9 set as analog */ + ... { + pinmux = <STM32_PINMUX('A', 9, ANALOG)>; + }; + Optional properties: - GENERIC_PINCONFIG: is the generic pinconfig options to use. Available options are: @@ -165,13 +183,13 @@ pin-controller { ... usart1_pins_a: usart1@0 { pins1 { - pinmux = <STM32F429_PA9_FUNC_USART1_TX>; + pinmux = <STM32_PINMUX('A', 9, AF7)>; bias-disable; drive-push-pull; slew-rate = <0>; }; pins2 { - pinmux = <STM32F429_PA10_FUNC_USART1_RX>; + pinmux = <STM32_PINMUX('A', 10, AF7)>; bias-disable; }; }; diff --git a/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt b/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt new file mode 100644 index 000000000000..1cd050b4054c --- /dev/null +++ b/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt @@ -0,0 +1,61 @@ +Amlogic Meson Power Controller +============================== + +The Amlogic Meson SoCs embeds an internal Power domain controller. + +VPU Power Domain +---------------- + +The Video Processing Unit power domain is controlled by this power controller, +but the domain requires some external resources to meet the correct power +sequences. +The bindings must respect the power domain bindings as described in the file +power_domain.txt + +Device Tree Bindings: +--------------------- + +Required properties: +- compatible: should be "amlogic,meson-gx-pwrc-vpu" for the Meson GX SoCs +- #power-domain-cells: should be 0 +- amlogic,hhi-sysctrl: phandle to the HHI sysctrl node +- resets: phandles to the reset lines needed for this power demain sequence + as described in ../reset/reset.txt +- clocks: from common clock binding: handle to VPU and VAPB clocks +- clock-names: from common clock binding: must contain "vpu", "vapb" + corresponding to entry in the clocks property. + +Parent node should have the following properties : +- compatible: "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd" +- reg: base address and size of the AO system control register space. + +Example: +------- + +ao_sysctrl: sys-ctrl@0 { + compatible = "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd"; + reg = <0x0 0x0 0x0 0x100>; + + pwrc_vpu: power-controller-vpu { + compatible = "amlogic,meson-gx-pwrc-vpu"; + #power-domain-cells = <0>; + amlogic,hhi-sysctrl = <&sysctrl>; + resets = <&reset RESET_VIU>, + <&reset RESET_VENC>, + <&reset RESET_VCBUS>, + <&reset RESET_BT656>, + <&reset RESET_DVIN_RESET>, + <&reset RESET_RDMA>, + <&reset RESET_VENCI>, + <&reset RESET_VENCP>, + <&reset RESET_VDAC>, + <&reset RESET_VDI6>, + <&reset RESET_VENCL>, + <&reset RESET_VID_LOCK>; + clocks = <&clkc CLKID_VPU>, + <&clkc CLKID_VAPB>; + clock-names = "vpu", "vapb"; + }; +}; + + diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt index af21502e939c..f747f95eee58 100644 --- a/Documentation/devicetree/bindings/power/renesas,apmu.txt +++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt @@ -8,6 +8,7 @@ Required properties: - compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback. Examples with soctypes are: - "renesas,r8a7743-apmu" (RZ/G1M) + - "renesas,r8a7745-apmu" (RZ/G1E) - "renesas,r8a7790-apmu" (R-Car H2) - "renesas,r8a7791-apmu" (R-Car M2-W) - "renesas,r8a7792-apmu" (R-Car V2H) diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt index 98cc8c09d02d..8690f10426a3 100644 --- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt +++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt @@ -17,6 +17,7 @@ Required properties: - "renesas,r8a7794-sysc" (R-Car E2) - "renesas,r8a7795-sysc" (R-Car H3) - "renesas,r8a7796-sysc" (R-Car M3-W) + - "renesas,r8a77970-sysc" (R-Car V3M) - "renesas,r8a77995-sysc" (R-Car D3) - reg: Address start and address range for the device. - #power-domain-cells: Must be 1. diff --git a/Documentation/devicetree/bindings/power/ti-smartreflex.txt b/Documentation/devicetree/bindings/power/ti-smartreflex.txt new file mode 100644 index 000000000000..9780957c9115 --- /dev/null +++ b/Documentation/devicetree/bindings/power/ti-smartreflex.txt @@ -0,0 +1,47 @@ +Texas Instruments SmartReflex binding + +SmartReflex is used to set and adjust the SoC operating points. + + +Required properties: + +compatible: Shall be one of the following: + "ti,omap3-smartreflex-core" + "ti,omap3-smartreflex-iva" + "ti,omap4-smartreflex-core" + "ti,omap4-smartreflex-mpu" + "ti,omap4-smartreflex-iva" + +reg: Shall contain the device instance IO range + +interrupts: Shall contain the device instance interrupt + + +Optional properties: + +ti,hwmods: Shall contain the TI interconnect module name if needed + by the SoC + + +Example: + + smartreflex_iva: smartreflex@4a0db000 { + compatible = "ti,omap4-smartreflex-iva"; + reg = <0x4a0db000 0x80>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "smartreflex_iva"; + }; + + smartreflex_core: smartreflex@4a0dd000 { + compatible = "ti,omap4-smartreflex-core"; + reg = <0x4a0dd000 0x80>; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "smartreflex_core"; + }; + + smartreflex_mpu: smartreflex@4a0d9000 { + compatible = "ti,omap4-smartreflex-mpu"; + reg = <0x4a0d9000 0x80>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "smartreflex_mpu"; + }; diff --git a/Documentation/devicetree/bindings/reserved-memory/qcom,rmtfs-mem.txt b/Documentation/devicetree/bindings/reserved-memory/qcom,rmtfs-mem.txt new file mode 100644 index 000000000000..8562ba1dce69 --- /dev/null +++ b/Documentation/devicetree/bindings/reserved-memory/qcom,rmtfs-mem.txt @@ -0,0 +1,51 @@ +Qualcomm Remote File System Memory binding + +This binding describes the Qualcomm remote filesystem memory, which serves the +purpose of describing the shared memory region used for remote processors to +access block device data using the Remote Filesystem protocol. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be: + "qcom,rmtfs-mem" + +- reg: + Usage: required for static allocation + Value type: <prop-encoded-array> + Definition: must specify base address and size of the memory region, + as described in reserved-memory.txt + +- size: + Usage: required for dynamic allocation + Value type: <prop-encoded-array> + Definition: must specify a size of the memory region, as described in + reserved-memory.txt + +- qcom,client-id: + Usage: required + Value type: <u32> + Definition: identifier of the client to use this region for buffers. + +- qcom,vmid: + Usage: optional + Value type: <u32> + Definition: vmid of the remote processor, to set up memory protection. + += EXAMPLE +The following example shows the remote filesystem memory setup for APQ8016, +with the rmtfs region for the Hexagon DSP (id #1) located at 0x86700000. + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + rmtfs@86700000 { + compatible = "qcom,rmtfs-mem"; + reg = <0x0 0x86700000 0x0 0xe0000>; + no-map; + + qcom,client-id = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/reset/renesas,rst.txt b/Documentation/devicetree/bindings/reset/renesas,rst.txt index e5a03ffe04fb..a8014f3ab8ba 100644 --- a/Documentation/devicetree/bindings/reset/renesas,rst.txt +++ b/Documentation/devicetree/bindings/reset/renesas,rst.txt @@ -26,6 +26,7 @@ Required properties: - "renesas,r8a7794-rst" (R-Car E2) - "renesas,r8a7795-rst" (R-Car H3) - "renesas,r8a7796-rst" (R-Car M3-W) + - "renesas,r8a77970-rst" (R-Car V3M) - "renesas,r8a77995-rst" (R-Car D3) - reg: Address start and address range for the device. diff --git a/Documentation/devicetree/bindings/reset/snps,axs10x-reset.txt b/Documentation/devicetree/bindings/reset/snps,axs10x-reset.txt new file mode 100644 index 000000000000..32d8435a41df --- /dev/null +++ b/Documentation/devicetree/bindings/reset/snps,axs10x-reset.txt @@ -0,0 +1,33 @@ +Binding for the AXS10x reset controller + +This binding describes the ARC AXS10x boards custom IP-block which allows +to control reset signals of selected peripherals. For example DW GMAC, etc... +This block is controlled via memory-mapped register (AKA CREG) which +represents up-to 32 reset lines. + +As of today only the following lines are used: + - DW GMAC - line 5 + +This binding uses the common reset binding[1]. + +[1] Documentation/devicetree/bindings/reset/reset.txt + +Required properties: +- compatible: should be "snps,axs10x-reset". +- reg: should always contain pair address - length: for creg reset + bits register. +- #reset-cells: from common reset binding; Should always be set to 1. + +Example: + reset: reset-controller@11220 { + compatible = "snps,axs10x-reset"; + #reset-cells = <1>; + reg = <0x11220 0x4>; + }; + +Specifying reset lines connected to IP modules: + ethernet@.... { + .... + resets = <&reset 5>; + .... + }; diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt index 68a6f487c409..93efed629900 100644 --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt @@ -13,6 +13,7 @@ Required properties: "socionext,uniphier-pxs2-reset" - for PXs2/LD6b SoC "socionext,uniphier-ld11-reset" - for LD11 SoC "socionext,uniphier-ld20-reset" - for LD20 SoC + "socionext,uniphier-pxs3-reset" - for PXs3 SoC - #reset-cells: should be 1. Example: @@ -44,6 +45,7 @@ Required properties: "socionext,uniphier-ld11-mio-reset" - for LD11 SoC (MIO) "socionext,uniphier-ld11-sd-reset" - for LD11 SoC (SD) "socionext,uniphier-ld20-sd-reset" - for LD20 SoC + "socionext,uniphier-pxs3-sd-reset" - for PXs3 SoC - #reset-cells: should be 1. Example: @@ -74,6 +76,7 @@ Required properties: "socionext,uniphier-pxs2-peri-reset" - for PXs2/LD6b SoC "socionext,uniphier-ld11-peri-reset" - for LD11 SoC "socionext,uniphier-ld20-peri-reset" - for LD20 SoC + "socionext,uniphier-pxs3-peri-reset" - for PXs3 SoC - #reset-cells: should be 1. Example: diff --git a/Documentation/devicetree/bindings/riscv/cpus.txt b/Documentation/devicetree/bindings/riscv/cpus.txt new file mode 100644 index 000000000000..adf7b7af5dc3 --- /dev/null +++ b/Documentation/devicetree/bindings/riscv/cpus.txt @@ -0,0 +1,162 @@ +=================== +RISC-V CPU Bindings +=================== + +The device tree allows to describe the layout of CPUs in a system through +the "cpus" node, which in turn contains a number of subnodes (ie "cpu") +defining properties for every cpu. + +Bindings for CPU nodes follow the Devicetree Specification, available from: + +https://www.devicetree.org/specifications/ + +with updates for 32-bit and 64-bit RISC-V systems provided in this document. + +=========== +Terminology +=========== + +This document uses some terminology common to the RISC-V community that is not +widely used, the definitions of which are listed here: + +* hart: A hardware execution context, which contains all the state mandated by + the RISC-V ISA: a PC and some registers. This terminology is designed to + disambiguate software's view of execution contexts from any particular + microarchitectural implementation strategy. For example, my Intel laptop is + described as having one socket with two cores, each of which has two hyper + threads. Therefore this system has four harts. + +===================================== +cpus and cpu node bindings definition +===================================== + +The RISC-V architecture, in accordance with the Devicetree Specification, +requires the cpus and cpu nodes to be present and contain the properties +described below. + +- cpus node + + Description: Container of cpu nodes + + The node name must be "cpus". + + A cpus node must define the following properties: + + - #address-cells + Usage: required + Value type: <u32> + Definition: must be set to 1 + - #size-cells + Usage: required + Value type: <u32> + Definition: must be set to 0 + +- cpu node + + Description: Describes a hart context + + PROPERTIES + + - device_type + Usage: required + Value type: <string> + Definition: must be "cpu" + - reg + Usage: required + Value type: <u32> + Definition: The hart ID of this CPU node + - compatible: + Usage: required + Value type: <stringlist> + Definition: must contain "riscv", may contain one of + "sifive,rocket0" + - mmu-type: + Usage: optional + Value type: <string> + Definition: Specifies the CPU's MMU type. Possible values are + "riscv,sv32" + "riscv,sv39" + "riscv,sv48" + - riscv,isa: + Usage: required + Value type: <string> + Definition: Contains the RISC-V ISA string of this hart. These + ISA strings are defined by the RISC-V ISA manual. + +Example: SiFive Freedom U540G Development Kit +--------------------------------------------- + +This system contains two harts: a hart marked as disabled that's used for +low-level system tasks and should be ignored by Linux, and a second hart that +Linux is allowed to run on. + + cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <1000000>; + cpu@0 { + clock-frequency = <1600000000>; + compatible = "sifive,rocket0", "riscv"; + device_type = "cpu"; + i-cache-block-size = <64>; + i-cache-sets = <128>; + i-cache-size = <16384>; + next-level-cache = <&L15 &L0>; + reg = <0>; + riscv,isa = "rv64imac"; + status = "disabled"; + L10: interrupt-controller { + #interrupt-cells = <1>; + compatible = "riscv,cpu-intc"; + interrupt-controller; + }; + }; + cpu@1 { + clock-frequency = <1600000000>; + compatible = "sifive,rocket0", "riscv"; + d-cache-block-size = <64>; + d-cache-sets = <64>; + d-cache-size = <32768>; + d-tlb-sets = <1>; + d-tlb-size = <32>; + device_type = "cpu"; + i-cache-block-size = <64>; + i-cache-sets = <64>; + i-cache-size = <32768>; + i-tlb-sets = <1>; + i-tlb-size = <32>; + mmu-type = "riscv,sv39"; + next-level-cache = <&L15 &L0>; + reg = <1>; + riscv,isa = "rv64imafdc"; + status = "okay"; + tlb-split; + L13: interrupt-controller { + #interrupt-cells = <1>; + compatible = "riscv,cpu-intc"; + interrupt-controller; + }; + }; + }; + +Example: Spike ISA Simulator with 1 Hart +---------------------------------------- + +This device tree matches the Spike ISA golden model as run with `spike -p1`. + + cpus { + cpu@0 { + device_type = "cpu"; + reg = <0x00000000>; + status = "okay"; + compatible = "riscv"; + riscv,isa = "rv64imafdc"; + mmu-type = "riscv,sv48"; + clock-frequency = <0x3b9aca00>; + interrupt-controller { + #interrupt-cells = <0x00000001>; + interrupt-controller; + compatible = "riscv,cpu-intc"; + } + } + } diff --git a/Documentation/devicetree/bindings/serial/brcm,bcm6345-uart.txt b/Documentation/devicetree/bindings/serial/brcm,bcm6345-uart.txt index 5c52e5eef16d..8b2b0460259a 100644 --- a/Documentation/devicetree/bindings/serial/brcm,bcm6345-uart.txt +++ b/Documentation/devicetree/bindings/serial/brcm,bcm6345-uart.txt @@ -11,6 +11,11 @@ Required properties: - clocks: Clock driving the hardware; used to figure out the baud rate divisor. + +Optional properties: + +- clock-names: Should be "refclk". + Example: uart0: serial@14e00520 { @@ -19,6 +24,7 @@ Example: interrupt-parent = <&periph_intc>; interrupts = <2>; clocks = <&periph_clk>; + clock-names = "refclk"; }; clocks { diff --git a/Documentation/devicetree/bindings/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/serial/mvebu-uart.txt index 6087defd9f93..d37fabe17bd1 100644 --- a/Documentation/devicetree/bindings/serial/mvebu-uart.txt +++ b/Documentation/devicetree/bindings/serial/mvebu-uart.txt @@ -8,6 +8,6 @@ Required properties: Example: serial@12000 { compatible = "marvell,armada-3700-uart"; - reg = <0x12000 0x400>; + reg = <0x12000 0x200>; interrupts = <43>; }; diff --git a/Documentation/devicetree/bindings/soc/fsl/bman.txt b/Documentation/devicetree/bindings/soc/fsl/bman.txt index 47ac834414d8..48eed140765b 100644 --- a/Documentation/devicetree/bindings/soc/fsl/bman.txt +++ b/Documentation/devicetree/bindings/soc/fsl/bman.txt @@ -65,8 +65,8 @@ to the respective BMan instance BMan Private Memory Node BMan requires a contiguous range of physical memory used for the backing store -for BMan Free Buffer Proxy Records (FBPR). This memory is reserved/allocated as a -node under the /reserved-memory node +for BMan Free Buffer Proxy Records (FBPR). This memory is reserved/allocated as +a node under the /reserved-memory node. The BMan FBPR memory node must be named "bman-fbpr" @@ -75,7 +75,9 @@ PROPERTIES - compatible Usage: required Value type: <stringlist> - Definition: Must inclide "fsl,bman-fbpr" + Definition: PPC platforms: Must include "fsl,bman-fbpr" + ARM platforms: Must include "shared-dma-pool" + as well as the "no-map" property The following constraints are relevant to the FBPR private memory: - The size must be 2^(size + 1), with size = 11..33. That is 4 KiB to @@ -100,10 +102,10 @@ The example below shows a BMan FBPR dynamic allocation memory node ranges; bman_fbpr: bman-fbpr { - compatible = "fsl,bman-fbpr"; - alloc-ranges = <0 0 0x10 0>; + compatible = "shared-mem-pool"; size = <0 0x1000000>; alignment = <0 0x1000000>; + no-map; }; }; diff --git a/Documentation/devicetree/bindings/soc/fsl/qman.txt b/Documentation/devicetree/bindings/soc/fsl/qman.txt index 556ebb8be75d..ee96afd2af72 100644 --- a/Documentation/devicetree/bindings/soc/fsl/qman.txt +++ b/Documentation/devicetree/bindings/soc/fsl/qman.txt @@ -60,6 +60,12 @@ are located at offsets 0xbf8 and 0xbfc Value type: <prop-encoded-array> Definition: Reference input clock. Its frequency is half of the platform clock +- memory-regions + Usage: Required for ARM + Value type: <phandle array> + Definition: List of phandles referencing the QMan private memory + nodes (described below). The qman-fqd node must be + first followed by qman-pfdr node. Only used on ARM Devices connected to a QMan instance via Direct Connect Portals (DCP) must link to the respective QMan instance @@ -74,7 +80,9 @@ QMan Private Memory Nodes QMan requires two contiguous range of physical memory used for the backing store for QMan Frame Queue Descriptor (FQD) and Packed Frame Descriptor Record (PFDR). -This memory is reserved/allocated as a nodes under the /reserved-memory node +This memory is reserved/allocated as a node under the /reserved-memory node. + +For additional details about reserved memory regions see reserved-memory.txt The QMan FQD memory node must be named "qman-fqd" @@ -83,7 +91,9 @@ PROPERTIES - compatible Usage: required Value type: <stringlist> - Definition: Must inclide "fsl,qman-fqd" + Definition: PPC platforms: Must include "fsl,qman-fqd" + ARM platforms: Must include "shared-dma-pool" + as well as the "no-map" property The QMan PFDR memory node must be named "qman-pfdr" @@ -92,7 +102,9 @@ PROPERTIES - compatible Usage: required Value type: <stringlist> - Definition: Must inclide "fsl,qman-pfdr" + Definition: PPC platforms: Must include "fsl,qman-pfdr" + ARM platforms: Must include "shared-dma-pool" + as well as the "no-map" property The following constraints are relevant to the FQD and PFDR private memory: - The size must be 2^(size + 1), with size = 11..29. That is 4 KiB to @@ -117,16 +129,16 @@ The example below shows a QMan FQD and a PFDR dynamic allocation memory nodes ranges; qman_fqd: qman-fqd { - compatible = "fsl,qman-fqd"; - alloc-ranges = <0 0 0x10 0>; + compatible = "shared-dma-pool"; size = <0 0x400000>; alignment = <0 0x400000>; + no-map; }; qman_pfdr: qman-pfdr { - compatible = "fsl,qman-pfdr"; - alloc-ranges = <0 0 0x10 0>; + compatible = "shared-dma-pool"; size = <0 0x2000000>; alignment = <0 0x2000000>; + no-map; }; }; diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt index 107700d00df4..bf80e3f96f8c 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt @@ -19,6 +19,7 @@ IP Pairing Required properties in pwrap device node. - compatible: "mediatek,mt2701-pwrap" for MT2701/7623 SoCs + "mediatek,mt7622-pwrap" for MT7622 SoCs "mediatek,mt8135-pwrap" for MT8135 SoCs "mediatek,mt8173-pwrap" for MT8173 SoCs - interrupts: IRQ for pwrap in SOC @@ -36,9 +37,12 @@ Required properties in pwrap device node. - clocks: Must contain an entry for each entry in clock-names. Optional properities: -- pmic: Mediatek PMIC MFD is the child device of pwrap +- pmic: Using either MediaTek PMIC MFD as the child device of pwrap See the following for child node definitions: Documentation/devicetree/bindings/mfd/mt6397.txt + or the regulator-only device as the child device of pwrap, such as MT6380. + See the following definitions for such kinds of devices. + Documentation/devicetree/bindings/regulator/mt6380-regulator.txt Example: pwrap: pwrap@1000f000 { diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt index 4ea39e9186a7..042a2e4159bd 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt @@ -37,6 +37,11 @@ The following properties are defined to the bluetooth node: Definition: must be: "qcom,wcnss-bt" +- local-bd-address: + Usage: optional + Value type: <u8 array> + Definition: see Documentation/devicetree/bindings/net/bluetooth.txt + == WiFi The following properties are defined to the WiFi node: @@ -91,6 +96,9 @@ smd { bt { compatible = "qcom,wcnss-bt"; + + /* BD address 00:11:22:33:44:55 */ + local-bd-address = [ 55 44 33 22 11 00 ]; }; wlan { diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index 13b1fcc8469e..dcc7eaada511 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -5,6 +5,7 @@ Required properties: "fsl,ls2085a-dspi" or "fsl,ls2080a-dspi" followed by "fsl,ls2085a-dspi" + "fsl,ls1012a-dspi" followed by "fsl,ls1021a-v1.0-dspi" - reg : Offset and length of the register set for the device - interrupts : Should contain SPI controller interrupt - clocks: from common clock binding: handle to dspi clock. diff --git a/Documentation/devicetree/bindings/thermal/hisilicon-thermal.txt b/Documentation/devicetree/bindings/thermal/hisilicon-thermal.txt index d48fc5280d5a..cef716a236f1 100644 --- a/Documentation/devicetree/bindings/thermal/hisilicon-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/hisilicon-thermal.txt @@ -13,6 +13,7 @@ Example : +for Hi6220: tsensor: tsensor@0,f7030700 { compatible = "hisilicon,tsensor"; reg = <0x0 0xf7030700 0x0 0x1000>; @@ -21,3 +22,11 @@ Example : clock-names = "thermal_clk"; #thermal-sensor-cells = <1>; } + +for Hi3660: + tsensor: tsensor@fff30000 { + compatible = "hisilicon,hi3660-tsensor"; + reg = <0x0 0xfff30000 0x0 0x1000>; + interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>; + #thermal-sensor-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/thermal/nvidia,tegra186-bpmp-thermal.txt b/Documentation/devicetree/bindings/thermal/nvidia,tegra186-bpmp-thermal.txt new file mode 100644 index 000000000000..276387dd6815 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/nvidia,tegra186-bpmp-thermal.txt @@ -0,0 +1,32 @@ +NVIDIA Tegra186 BPMP thermal sensor + +In Tegra186, the BPMP (Boot and Power Management Processor) implements an +interface that is used to read system temperatures, including CPU cluster +and GPU temperatures. This binding describes the thermal sensor that is +exposed by BPMP. + +The BPMP thermal node must be located directly inside the main BPMP node. See +../firmware/nvidia,tegra186-bpmp.txt for details of the BPMP binding. + +This node represents a thermal sensor. See thermal.txt for details of the +core thermal binding. + +Required properties: +- compatible: + Array of strings. + One of: + - "nvidia,tegra186-bpmp-thermal". +- #thermal-sensor-cells: Cell for sensor index. + Single-cell integer. + Must be <1>. + +Example: + +bpmp { + ... + + bpmp_thermal: thermal { + compatible = "nvidia,tegra186-bpmp-thermal"; + #thermal-sensor-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 0f295a4798ad..0994bdd82cd3 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -18,6 +18,7 @@ al Annapurna Labs allwinner Allwinner Technology Co., Ltd. alphascale AlphaScale Integrated Circuits Systems, Inc. altr Altera Corp. +amarula Amarula Solutions amazon Amazon.com, Inc. amcc Applied Micro Circuits Corporation (APM, formally AMCC) amd Advanced Micro Devices (AMD), Inc. @@ -114,6 +115,7 @@ everspin Everspin Technologies, Inc. exar Exar Corporation excito Excito ezchip EZchip Semiconductor +fairphone Fairphone B.V. faraday Faraday Technology Corporation fcs Fairchild Semiconductor firefly Firefly @@ -199,6 +201,7 @@ mcube mCube meas Measurement Specialties mediatek MediaTek Inc. megachips MegaChips +mele Shenzhen MeLE Digital Technology Ltd. melexis Melexis N.V. melfas MELFAS Inc. mellanox Mellanox Technologies @@ -254,6 +257,7 @@ opencores OpenCores.org openrisc OpenRISC.io option Option NV ORCL Oracle Corporation +orisetech Orise Technology ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies oxsemi Oxford Semiconductor, Ltd. @@ -269,6 +273,7 @@ plathome Plat'Home Co., Ltd. plda PLDA poslab Poslab Technology Co., Ltd. powervr PowerVR (deprecated, use img) +probox2 PROBOX2 (by W2COMP Co., Ltd.) pulsedlight PulsedLight, Inc qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc @@ -337,6 +342,7 @@ swir Sierra Wireless syna Synaptics Inc. synology Synology, Inc. tbs TBS Technologies +tbs-biometrics Touchless Biometric Systems AG tcg Trusted Computing Group tcl Toby Churchill Ltd. technexion TechNexion @@ -360,6 +366,7 @@ truly Truly Semiconductors Limited tsd Theobroma Systems Design und Consulting GmbH tyan Tyan Computer Corporation ucrobotics uCRobotics +ubnt Ubiquiti Networks udoo Udoo uniwest United Western Technologies Corp (UniWest) upisemi uPI Semiconductor Corp. |