diff options
Diffstat (limited to 'Documentation/devicetree')
79 files changed, 1585 insertions, 98 deletions
diff --git a/Documentation/devicetree/bindings/arm/gic-v3.txt b/Documentation/devicetree/bindings/arm/gic-v3.txt index ddfade40ac59..7803e77d85cb 100644 --- a/Documentation/devicetree/bindings/arm/gic-v3.txt +++ b/Documentation/devicetree/bindings/arm/gic-v3.txt @@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs. These nodes must have the following properties: - compatible : Should at least contain "arm,gic-v3-its". - msi-controller : Boolean property. Identifies the node as an MSI controller +- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device + which will generate the MSI. - reg: Specifies the base physical address and size of the ITS registers. @@ -83,6 +85,7 @@ Examples: gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c200000 0 0x200000>; }; }; @@ -107,12 +110,14 @@ Examples: gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c200000 0 0x200000>; }; gic-its@2c400000 { compatible = "arm,gic-v3-its"; msi-controller; + #msi-cells = <1>; reg = <0x0 0x2c400000 0 0x200000>; }; }; diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index 2da059a4790c..cc56021eb60b 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -11,13 +11,14 @@ have PPIs or SGIs. Main node required properties: - compatible : should be one of: - "arm,gic-400" + "arm,arm1176jzf-devchip-gic" + "arm,arm11mp-gic" "arm,cortex-a15-gic" - "arm,cortex-a9-gic" "arm,cortex-a7-gic" - "arm,arm11mp-gic" + "arm,cortex-a9-gic" + "arm,gic-400" + "arm,pl390" "brcm,brahma-b15-gic" - "arm,arm1176jzf-devchip-gic" "qcom,msm-8660-qgic" "qcom,msm-qgic2" - interrupt-controller : Identifies the node as an interrupt controller @@ -58,6 +59,21 @@ Optional regions, used when the GIC doesn't have banked registers. The offset is cpu-offset * cpu-nr. +- clocks : List of phandle and clock-specific pairs, one for each entry + in clock-names. +- clock-names : List of names for the GIC clock input(s). Valid clock names + depend on the GIC variant: + "ic_clk" (for "arm,arm11mp-gic") + "PERIPHCLKEN" (for "arm,cortex-a15-gic") + "PERIPHCLK", "PERIPHCLKEN" (for "arm,cortex-a9-gic") + "clk" (for "arm,gic-400") + "gclk" (for "arm,pl390") + +- power-domains : A phandle and PM domain specifier as defined by bindings of + the power controller specified by phandle, used when the GIC + is part of a Power or Clock Domain. + + Example: intc: interrupt-controller@fff11000 { diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt index a8274eabae2e..b8e41c148a3c 100644 --- a/Documentation/devicetree/bindings/arm/idle-states.txt +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -497,7 +497,7 @@ cpus { }; idle-states { - entry-method = "arm,psci"; + entry-method = "psci"; CPU_RETENTION_0_0: cpu-retention-0-0 { compatible = "arm,idle-state"; diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 435251fa9ce0..4b7c3d9b29bb 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -8,6 +8,8 @@ Required properties: - compatible : should be one of "arm,armv8-pmuv3" + "arm.cortex-a57-pmu" + "arm.cortex-a53-pmu" "arm,cortex-a17-pmu" "arm,cortex-a15-pmu" "arm,cortex-a12-pmu" diff --git a/Documentation/devicetree/bindings/arm/twd.txt b/Documentation/devicetree/bindings/arm/twd.txt index 75b8610939fa..383ea19c2bf0 100644 --- a/Documentation/devicetree/bindings/arm/twd.txt +++ b/Documentation/devicetree/bindings/arm/twd.txt @@ -19,6 +19,11 @@ interrupts. - reg : Specify the base address and the size of the TWD timer register window. +Optional + +- always-on : a boolean property. If present, the timer is powered through + an always-on power domain, therefore it never loses context. + Example: twd-timer@2c000600 { diff --git a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt index 78edb80002c8..78e2a31c58d0 100644 --- a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt +++ b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt @@ -5,6 +5,8 @@ The follow error types are supported: memory controller - Memory controller PMD (L1/L2) - Processor module unit (PMD) L1/L2 cache + L3 - L3 cache controller + SoC - SoC IP's such as Ethernet, SATA, and etc The following section describes the EDAC DT node binding. @@ -30,6 +32,17 @@ Required properties for PMD subnode: - reg : First resource shall be the PMD resource. - pmd-controller : Instance number of the PMD controller. +Required properties for L3 subnode: +- compatible : Shall be "apm,xgene-edac-l3" or + "apm,xgene-edac-l3-v2". +- reg : First resource shall be the L3 EDAC resource. + +Required properties for SoC subnode: +- compatible : Shall be "apm,xgene-edac-soc-v1" for revision 1 or + "apm,xgene-edac-l3-soc" for general value reporting + only. +- reg : First resource shall be the SoC EDAC resource. + Example: csw: csw@7e200000 { compatible = "apm,xgene-csw", "syscon"; @@ -76,4 +89,14 @@ Example: reg = <0x0 0x7c000000 0x0 0x200000>; pmd-controller = <0>; }; + + edacl3@7e600000 { + compatible = "apm,xgene-edac-l3"; + reg = <0x0 0x7e600000 0x0 0x1000>; + }; + + edacsoc@7e930000 { + compatible = "apm,xgene-edac-soc-v1"; + reg = <0x0 0x7e930000 0x0 0x1000>; + }; }; diff --git a/Documentation/devicetree/bindings/fpga/xilinx-zynq-fpga-mgr.txt b/Documentation/devicetree/bindings/fpga/xilinx-zynq-fpga-mgr.txt new file mode 100644 index 000000000000..7018aa896835 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/xilinx-zynq-fpga-mgr.txt @@ -0,0 +1,19 @@ +Xilinx Zynq FPGA Manager + +Required properties: +- compatible: should contain "xlnx,zynq-devcfg-1.0" +- reg: base address and size for memory mapped io +- interrupts: interrupt for the FPGA manager device +- clocks: phandle for clocks required operation +- clock-names: name for the clock, should be "ref_clk" +- syscon: phandle for access to SLCR registers + +Example: + devcfg: devcfg@f8007000 { + compatible = "xlnx,zynq-devcfg-1.0"; + reg = <0xf8007000 0x100>; + interrupts = <0 8 4>; + clocks = <&clkc 12>; + clock-names = "ref_clk"; + syscon = <&slcr>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-msm.txt b/Documentation/devicetree/bindings/gpio/gpio-msm.txt deleted file mode 100644 index ac20e68a004e..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-msm.txt +++ /dev/null @@ -1,26 +0,0 @@ -MSM GPIO controller bindings - -Required properties: -- compatible: - - "qcom,msm-gpio" for MSM controllers -- #gpio-cells : Should be two. - - first cell is the pin number - - second cell is used to specify optional parameters (unused) -- gpio-controller : Marks the device node as a GPIO controller. -- #interrupt-cells : Should be 2. -- interrupt-controller: Mark the device node as an interrupt controller -- interrupts : Specify the TLMM summary interrupt number -- ngpio : Specify the number of MSM GPIOs - -Example: - - msmgpio: gpio@fd510000 { - compatible = "qcom,msm-gpio"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0xfd510000 0x4000>; - interrupts = <0 208 0>; - ngpio = <150>; - }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index b9a42f294dd0..13df9933f4cd 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -24,6 +24,7 @@ Required properties: ti,tca6408 ti,tca6416 ti,tca6424 + ti,tca9539 exar,xra1202 Example: diff --git a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt index db4c6a663c03..7b542657f259 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt @@ -12,6 +12,13 @@ Required properties: - interrupts : Interrupt specifier (see interrupt bindings for details) - interrupt-parent : Must be core interrupt controller +- interrupt-controller : Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. - reg : Address and length of the register set for the device Example: @@ -22,5 +29,7 @@ Example: gpio-controller; interrupt-parent = <&intc>; interrupts = <0 20 4>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0xe000a000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 5788d5cf1252..069cdf6f9dac 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -16,7 +16,9 @@ properties, each containing a 'gpio-list': GPIO properties should be named "[<name>-]gpios", with <name> being the purpose of this GPIO for the device. While a non-existent <name> is considered valid for compatibility reasons (resolving to the "gpios" property), it is not allowed -for new bindings. +for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old +bindings use it, but are only supported for compatibility reasons and should not +be used for newer bindings since it has been deprecated. GPIO properties can contain one or more GPIO phandles, but only in exceptional cases should they contain more than one. If your device uses several GPIOs with @@ -52,9 +54,13 @@ only uses one. gpio-specifier may encode: bank, pin position inside the bank, whether pin is open-drain and whether pin is logically inverted. + Exact meaning of each specifier cell is controller specific, and must -be documented in the device tree binding for the device. Use the macros -defined in include/dt-bindings/gpio/gpio.h whenever possible: +be documented in the device tree binding for the device. + +Most controllers are however specifying a generic flag bitfield +in the last cell, so for these, use the macros defined in +include/dt-bindings/gpio/gpio.h whenever possible: Example of a node using GPIOs: @@ -65,6 +71,15 @@ Example of a node using GPIOs: GPIO_ACTIVE_HIGH is 0, so in this example gpio-specifier is "18 0" and encodes GPIO pin number, and GPIO flags as accepted by the "qe_pio_e" gpio-controller. +Optional standard bitfield specifiers for the last cell: + +- Bit 0: 0 means active high, 1 means active low +- Bit 1: 1 means single-ended wiring, see: + https://en.wikipedia.org/wiki/Single-ended_triode + When used with active-low, this means open drain/collector, see: + https://en.wikipedia.org/wiki/Open_collector + When used with active-high, this means open source/emitter + 1.1) GPIO specifier best practices ---------------------------------- @@ -116,6 +131,30 @@ Every GPIO controller node must contain both an empty "gpio-controller" property, and a #gpio-cells integer property, which indicates the number of cells in a gpio-specifier. +Optionally, a GPIO controller may have a "ngpios" property. This property +indicates the number of in-use slots of available slots for GPIOs. The +typical example is something like this: the hardware register is 32 bits +wide, but only 18 of the bits have a physical counterpart. The driver is +generally written so that all 32 bits can be used, but the IP block is reused +in a lot of designs, some using all 32 bits, some using 18 and some using +12. In this case, setting "ngpios = <18>;" informs the driver that only the +first 18 GPIOs, at local offset 0 .. 17, are in use. + +If these GPIOs do not happen to be the first N GPIOs at offset 0...N-1, an +additional bitmask is needed to specify which GPIOs are actually in use, +and which are dummies. The bindings for this case has not yet been +specified, but should be specified if/when such hardware appears. + +Example: + +gpio-controller@00000000 { + compatible = "foo"; + reg = <0x00000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <18>; +} + The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism providing automatic GPIO request and configuration as part of the gpio-controller's driver probe function. diff --git a/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt b/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt new file mode 100644 index 000000000000..50ec2e690701 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt @@ -0,0 +1,22 @@ +Binding for the GPIO extension bus found on some LaCie/Seagate boards +(Example: 2Big/5Big Network v2, 2Big NAS). + +Required properties: +- compatible: "lacie,netxbig-gpio-ext". +- addr-gpios: GPIOs representing the address register (LSB -> MSB). +- data-gpios: GPIOs representing the data register (LSB -> MSB). +- enable-gpio: latches the new configuration (address, data) on raising edge. + +Example: + +netxbig_gpio_ext: netxbig-gpio-ext { + compatible = "lacie,netxbig-gpio-ext"; + + addr-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH + &gpio1 16 GPIO_ACTIVE_HIGH + &gpio1 17 GPIO_ACTIVE_HIGH>; + data-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH + &gpio1 13 GPIO_ACTIVE_HIGH + &gpio1 14 GPIO_ACTIVE_HIGH>; + enable-gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index d77d412cbc68..c50cf13c852e 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -54,7 +54,6 @@ epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer -fsl,mma8452 MMA8452Q: 3-axis 12-bit / 8-bit Digital Accelerometer fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface @@ -80,6 +79,7 @@ oki,ml86v7667 OKI ML86V7667 video decoder ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus pericom,pt7c4338 Real-time Clock Module plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch +pulsedlight,lidar-lite-v2 Pulsedlight LIDAR range-finding sensor ramtron,24c64 i2c serial eeprom (24cxx) ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC @@ -88,6 +88,7 @@ ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) +sgx,vz89x SGX Sensortech VZ89X Sensors sii,s35390a 2-wire CMOS real-time clock skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply st-micro,24c256 i2c serial eeprom (24cxx) diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt index c5933573e0f6..4a3679d54457 100644 --- a/Documentation/devicetree/bindings/iio/accel/bma180.txt +++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt @@ -1,10 +1,11 @@ -* Bosch BMA180 triaxial acceleration sensor +* Bosch BMA180 / BMA250 triaxial acceleration sensor http://omapworld.com/BMA180_111_1002839.pdf +http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf Required properties: - - compatible : should be "bosch,bma180" + - compatible : should be "bosch,bma180" or "bosch,bma250" - reg : the I2C address of the sensor Optional properties: @@ -13,6 +14,9 @@ Optional properties: - interrupts : interrupt mapping for GPIO IRQ, it should by configured with flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING + For the bma250 the first interrupt listed must be the one + connected to the INT1 pin, the second (optional) interrupt + listed must be the one connected to the INT2 pin. Example: diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt new file mode 100644 index 000000000000..e3c37467d7da --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -0,0 +1,24 @@ +Freescale MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC triaxial accelerometer + +Required properties: + + - compatible: should contain one of + * "fsl,mma8452" + * "fsl,mma8453" + * "fsl,mma8652" + * "fsl,mma8653" + - reg: the I2C address of the chip + +Optional properties: + + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: interrupt mapping for GPIO IRQ + +Example: + + mma8453fc@1d { + compatible = "fsl,mma8453"; + reg = <0x1d>; + interrupt-parent = <&gpio1>; + interrupts = <5 0>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/hi8435.txt b/Documentation/devicetree/bindings/iio/adc/hi8435.txt new file mode 100644 index 000000000000..3b0348c5e516 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/hi8435.txt @@ -0,0 +1,21 @@ +Holt Integrated Circuits HI-8435 threshold detector bindings + +Required properties: + - compatible: should be "holt,hi8435" + - reg: spi chip select number for the device + +Recommended properties: + - spi-max-frequency: definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: + - gpios: GPIO used for controlling the reset pin + +Example: +sensor@0 { + compatible = "holt,hi8435"; + reg = <0>; + gpios = <&gpio6 1 0>; + + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/apds9960.txt b/Documentation/devicetree/bindings/iio/light/apds9960.txt new file mode 100644 index 000000000000..174b709f16db --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/apds9960.txt @@ -0,0 +1,22 @@ +* Avago APDS9960 gesture/RGB/ALS/proximity sensor + +http://www.avagotech.com/docs/AV02-4191EN + +Required properties: + + - compatible: must be "avago,apds9960" + - reg: the I2c address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts : the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +apds9960@39 { + compatible = "avago,apds9960"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <16 1>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/us5182d.txt b/Documentation/devicetree/bindings/iio/light/us5182d.txt new file mode 100644 index 000000000000..6f0a530144fd --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/us5182d.txt @@ -0,0 +1,34 @@ +* UPISEMI us5182d I2C ALS and Proximity sensor + +Required properties: +- compatible: must be "upisemi,usd5182" +- reg: the I2C address of the device + +Optional properties: +- upisemi,glass-coef: glass attenuation factor - compensation factor of + resolution 1000 for material transmittance. +- upisemi,dark-ths: array of 8 elements containing 16-bit thresholds (adc + counts) corresponding to every scale. +- upisemi,upper-dark-gain: 8-bit dark gain compensation factor(4 int and 4 + fractional bits - Q4.4) applied when light > threshold +- upisemi,lower-dark-gain: 8-bit dark gain compensation factor(4 int and 4 + fractional bits - Q4.4) applied when light < threshold + +If the optional properties are not specified these factors will default to the +values in the below example. +The glass-coef defaults to no compensation for the covering material. +The threshold array defaults to experimental values that work with US5182D +sensor on evaluation board - roughly between 12-32 lux. +There will be no dark-gain compensation by default when ALS > thresh +(0 * dark-gain), and a 1.35 compensation factor when ALS < thresh. + +Example: + + usd5182@39 { + compatible = "upisemi,usd5182"; + reg = <0x39>; + upisemi,glass-coef = < 1000 >; + upisemi,dark-ths = /bits/ 16 <170 200 512 512 800 2000 4000 8000>; + upisemi,upper-dark-gain = /bits/ 8 <0x00>; + upisemi,lower-dark-gain = /bits/ 8 <0x16>; + }; diff --git a/Documentation/devicetree/bindings/input/cypress,cyapa.txt b/Documentation/devicetree/bindings/input/cypress,cyapa.txt index 635a3b036630..8d91ba9ff2fd 100644 --- a/Documentation/devicetree/bindings/input/cypress,cyapa.txt +++ b/Documentation/devicetree/bindings/input/cypress,cyapa.txt @@ -25,7 +25,7 @@ Example: /* Cypress Gen3 touchpad */ touchpad@67 { compatible = "cypress,cyapa"; - reg = <0x24>; + reg = <0x67>; interrupt-parent = <&gpio>; interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO 2 */ wakeup-source; diff --git a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt index 391717a68f3b..ec96b1f01478 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt @@ -4,8 +4,8 @@ The MISC interrupt controller is a secondary controller for lower priority interrupt. Required Properties: -- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" - as fallback +- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" or + "qca,<soctype>-cpu-intc", "qca,ar7240-misc-intc" - reg: Base address and size of the controllers memory area - interrupt-parent: phandle of the parent interrupt controller. - interrupts: Interrupt specifier for the controllers interrupt. @@ -13,6 +13,9 @@ Required Properties: - #interrupt-cells : Specifies the number of cells needed to encode interrupt source, should be 1 +Compatible fallback depends on the SoC. Use ar7100 for ar71xx and ar913x, +use ar7240 for all other SoCs. + Please refer to interrupts.txt in this directory for details of the common Interrupt Controllers bindings used by client devices. @@ -28,3 +31,16 @@ Example: interrupt-controller; #interrupt-cells = <1>; }; + +Another example: + + interrupt-controller@18060010 { + compatible = "qca,ar9331-misc-intc", qca,ar7240-misc-intc"; + reg = <0x18060010 0x4>; + + interrupt-parent = <&cpuintc>; + interrupts = <6>; + + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index 63633bdea7e4..ae5054c27c99 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -10,6 +10,7 @@ Required properties: - "renesas,irqc-r8a7792" (R-Car V2H) - "renesas,irqc-r8a7793" (R-Car M2-N) - "renesas,irqc-r8a7794" (R-Car E2) + - "renesas,intc-ex-r8a7795" (R-Car H3) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory - clocks: Must contain a reference to the functional clock. diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt index c05ed91a4e42..85c0c58617f6 100644 --- a/Documentation/devicetree/bindings/leds/leds-aat1290.txt +++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt @@ -27,9 +27,9 @@ Required properties of the LED child node: - flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt Maximum flash LED supply current can be calculated using following formula: I = 1A * 162kohm / Rset. -- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt - Maximum flash timeout can be calculated using following - formula: T = 8.82 * 10^9 * Ct. +- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt + Maximum flash timeout can be calculated using following + formula: T = 8.82 * 10^9 * Ct. Optional properties of the LED child node: - label : see Documentation/devicetree/bindings/leds/common.txt @@ -54,7 +54,7 @@ aat1290 { label = "aat1290-flash"; led-max-microamp = <520833>; flash-max-microamp = <1012500>; - flash-timeout-us = <1940000>; + flash-max-timeout-us = <1940000>; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt index f9e36adc0ebf..3f48c1eaf085 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt @@ -29,6 +29,14 @@ Required properties: Optional properties: - brcm,serial-leds : Boolean, enables Serial LEDs. Default : false + - brcm,serial-mux : Boolean, enables Serial LEDs multiplexing. + Default : false + - brcm,serial-clk-low : Boolean, makes clock signal active low. + Default : false + - brcm,serial-dat-low : Boolean, makes data signal active low. + Default : false + - brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction. + Default : false Each LED is represented as a sub-node of the brcm,bcm6328-leds device. @@ -110,6 +118,8 @@ Scenario 2 : BCM63268 with Serial/GPHY0 LEDs #size-cells = <0>; reg = <0x10001900 0x24>; brcm,serial-leds; + brcm,serial-dat-low; + brcm,serial-shift-inv; gphy0_spd0@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/leds/leds-netxbig.txt b/Documentation/devicetree/bindings/leds/leds-netxbig.txt new file mode 100644 index 000000000000..5ef92a26d768 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-netxbig.txt @@ -0,0 +1,92 @@ +Binding for the CPLD LEDs (GPIO extension bus) found on some LaCie/Seagate +boards (Example: 2Big/5Big Network v2, 2Big NAS). + +Required properties: +- compatible: "lacie,netxbig-leds". +- gpio-ext: Phandle for the gpio-ext bus. + +Optional properties: +- timers: Timer array. Each timer entry is represented by three integers: + Mode (gpio-ext bus), delay_on and delay_off. + +Each LED is represented as a sub-node of the netxbig-leds device. + +Required sub-node properties: +- mode-addr: Mode register address on gpio-ext bus. +- mode-val: Mode to value mapping. Each entry is represented by two integers: + A mode and the corresponding value on the gpio-ext bus. +- bright-addr: Brightness register address on gpio-ext bus. +- max-brightness: Maximum brightness value. + +Optional sub-node properties: +- label: Name for this LED. If omitted, the label is taken from the node name. +- linux,default-trigger: Trigger assigned to the LED. + +Example: + +netxbig-leds { + compatible = "lacie,netxbig-leds"; + + gpio-ext = &gpio_ext; + + timers = <NETXBIG_LED_TIMER1 500 500 + NETXBIG_LED_TIMER2 500 1000>; + + blue-power { + label = "netxbig:blue:power"; + mode-addr = <0>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 1 + NETXBIG_LED_TIMER1 3 + NETXBIG_LED_TIMER2 7>; + bright-addr = <1>; + max-brightness = <7>; + }; + red-power { + label = "netxbig:red:power"; + mode-addr = <0>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <1>; + max-brightness = <7>; + }; + blue-sata0 { + label = "netxbig:blue:sata0"; + mode-addr = <3>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 7 + NETXBIG_LED_SATA 1 + NETXBIG_LED_TIMER1 3>; + bright-addr = <2>; + max-brightness = <7>; + }; + red-sata0 { + label = "netxbig:red:sata0"; + mode-addr = <3>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <2>; + max-brightness = <7>; + }; + blue-sata1 { + label = "netxbig:blue:sata1"; + mode-addr = <4>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 7 + NETXBIG_LED_SATA 1 + NETXBIG_LED_TIMER1 3>; + bright-addr = <2>; + max-brightness = <7>; + }; + red-sata1 { + label = "netxbig:red:sata1"; + mode-addr = <4>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <2>; + max-brightness = <7>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt index 4ef45636ebde..38941db23dd2 100644 --- a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt +++ b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt @@ -4,7 +4,8 @@ Required properties: - compatible : should be one of: "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg", - "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg"; + "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg", + "samsung,exynos5433-jpeg"; - reg : address and length of the JPEG codec IP register set; - interrupts : specifies the JPEG codec IP interrupt; - clock-names : should contain: diff --git a/Documentation/devicetree/bindings/misc/sram.txt b/Documentation/devicetree/bindings/misc/sram.txt index 36cbe5aea990..42ee9438b771 100644 --- a/Documentation/devicetree/bindings/misc/sram.txt +++ b/Documentation/devicetree/bindings/misc/sram.txt @@ -33,6 +33,12 @@ Optional properties in the area nodes: - compatible : standard definition, should contain a vendor specific string in the form <vendor>,[<device>-]<usage> +- pool : indicates that the particular reserved SRAM area is addressable + and in use by another device or devices +- export : indicates that the reserved SRAM area may be accessed outside + of the kernel, e.g. by bootloader or userspace +- label : the name for the reserved partition, if omitted, the label + is taken from the node name excluding the unit address. Example: @@ -48,4 +54,14 @@ sram: sram@5c000000 { compatible = "socvendor,smp-sram"; reg = <0x100 0x50>; }; + + device-sram@1000 { + reg = <0x1000 0x1000>; + pool; + }; + + exported@20000 { + reg = <0x20000 0x20000>; + export; + }; }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index b7943f3f9995..dedfb02c744a 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -22,6 +22,8 @@ Optional properties: - voltage-ranges : two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). Several ranges could be specified. + - little-endian : If the host controller is little-endian mode, specify + this property. The default endian mode is big-endian. Example: diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 0384fc3f64e8..f693baf87264 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -37,6 +37,7 @@ Optional properties: - sd-uhs-sdr104: SD UHS SDR104 speed is supported - sd-uhs-ddr50: SD UHS DDR50 speed is supported - cap-power-off-card: powering off the card is safe +- cap-mmc-hw-reset: eMMC hardware reset is supported - cap-sdio-irq: enable SDIO IRQ signalling on this interface - full-pwr-cycle: full power cycle of the card is supported - mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index a1adfa495ad3..0120c7f1109c 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -17,6 +17,11 @@ Required properties: - vmmc-supply: power to the Core - vqmmc-supply: power to the IO +Optional properties: +- assigned-clocks: PLL of the source clock +- assigned-clock-parents: parent of source clock, used for HS400 mode to get 400Mhz source clock +- hs400-ds-delay: HS400 DS delay setting + Examples: mmc0: mmc@11230000 { compatible = "mediatek,mt8173-mmc", "mediatek,mt8135-mmc"; @@ -24,9 +29,13 @@ mmc0: mmc@11230000 { interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>; vmmc-supply = <&mt6397_vemc_3v3_reg>; vqmmc-supply = <&mt6397_vio18_reg>; - clocks = <&pericfg CLK_PERI_MSDC30_0>, <&topckgen CLK_TOP_MSDC50_0_H_SEL>; + clocks = <&pericfg CLK_PERI_MSDC30_0>, + <&topckgen CLK_TOP_MSDC50_0_H_SEL>; clock-names = "source", "hclk"; pinctrl-names = "default", "state_uhs"; pinctrl-0 = <&mmc0_pins_default>; pinctrl-1 = <&mmc0_pins_uhs>; + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>; + hs400-ds-delay = <0x14015>; }; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index d38942f6c5ae..cae29eb5733d 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -6,11 +6,12 @@ and the properties used by the MMCIF device. Required properties: -- compatible: must contain one of the following +- compatible: should be "renesas,mmcif-<soctype>", "renesas,sh-mmcif" as a + fallback. Examples with <soctype> are: - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs - - "renesas,sh-mmcif" for the generic MMCIF + - "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs - clocks: reference to the functional clock diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index c327c2d6f23d..3dc13b68fc3f 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -14,6 +14,19 @@ Required Properties: before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 +Optional Properties: +* clocks: from common clock binding: if ciu_drive and ciu_sample are + specified in clock-names, should contain handles to these clocks. + +* clock-names: Apart from the clock-names described in synopsys-dw-mshc.txt + two more clocks "ciu-drive" and "ciu-sample" are supported. They are used + to control the clock phases, "ciu-sample" is required for tuning high- + speed modes. + +* rockchip,default-sample-phase: The default phase to set ciu_sample at + probing, low speeds or in case where all phases work at tuning time. + If not specified 0 deg will be used. + Example: rkdwmmc0@12200000 { diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 346c6095a615..8636f5ae97e5 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -75,6 +75,12 @@ Optional properties: * vmmc-supply: The phandle to the regulator to use for vmmc. If this is specified we'll defer probe until we can find this regulator. +* dmas: List of DMA specifiers with the controller specific format as described + in the generic DMA client binding. Refer to dma.txt for details. + +* dma-names: request names for generic DMA client binding. Must be "rx-tx". + Refer to dma.txt for details. + Aliases: - All the MSHC controller nodes should be represented in the aliases node using @@ -95,6 +101,23 @@ board specific portions as listed below. #size-cells = <0>; }; +[board specific internal DMA resources] + + dwmmc0@12200000 { + clock-frequency = <400000000>; + clock-freq-min-max = <400000 200000000>; + num-slots = <1>; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + vmmc-supply = <&buck8>; + bus-width = <8>; + cap-mmc-highspeed; + cap-sd-highspeed; + }; + +[board specific generic DMA request binding] + dwmmc0@12200000 { clock-frequency = <400000000>; clock-freq-min-max = <400000 200000000>; @@ -106,4 +129,6 @@ board specific portions as listed below. bus-width = <8>; cap-mmc-highspeed; cap-sd-highspeed; + dmas = <&pdma 12>; + dma-names = "rx-tx"; }; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index f55aa280d34f..078060a97f95 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -37,6 +37,14 @@ Required properties for ethernet interfaces that have external PHY: Optional properties: - status: Should be "ok" or "disabled" for enabled/disabled. Default is "ok". +- tx-delay: Delay value for RGMII bridge TX clock. + Valid values are between 0 to 7, that maps to + 417, 717, 1020, 1321, 1611, 1913, 2215, 2514 ps + Default value is 4, which corresponds to 1611 ps +- rx-delay: Delay value for RGMII bridge RX clock. + Valid values are between 0 to 7, that maps to + 273, 589, 899, 1222, 1480, 1806, 2147, 2464 ps + Default value is 2, which corresponds to 899 ps Example: menetclk: menetclk { @@ -72,5 +80,7 @@ Example: /* Board-specific peripheral configurations */ &menet { + tx-delay = <4>; + rx-delay = <2>; status = "ok"; }; diff --git a/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt b/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt new file mode 100644 index 000000000000..8ba9ed11d716 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt @@ -0,0 +1,23 @@ +* Broadcom iProc MDIO bus controller + +Required properties: +- compatible: should be "brcm,iproc-mdio" +- reg: address and length of the register set for the MDIO interface +- #size-cells: must be 1 +- #address-cells: must be 0 + +Child nodes of this MDIO bus controller node are standard Ethernet PHY device +nodes as described in Documentation/devicetree/bindings/net/phy.txt + +Example: + +mdio@18002000 { + compatible = "brcm,iproc-mdio"; + reg = <0x18002000 0x8>; + #size-cells = <1>; + #address-cells = <0>; + + enet-gphy@0 { + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/can/sun4i_can.txt b/Documentation/devicetree/bindings/net/can/sun4i_can.txt new file mode 100644 index 000000000000..84ed1909df76 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/sun4i_can.txt @@ -0,0 +1,36 @@ +Allwinner A10/A20 CAN controller Device Tree Bindings +----------------------------------------------------- + +Required properties: +- compatible: "allwinner,sun4i-a10-can" +- reg: physical base address and size of the Allwinner A10/A20 CAN register map. +- interrupts: interrupt specifier for the sole interrupt. +- clock: phandle and clock specifier. + +Example +------- + +SoC common .dtsi file: + + can0_pins_a: can0@0 { + allwinner,pins = "PH20","PH21"; + allwinner,function = "can"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; +... + can0: can@01c2bc00 { + compatible = "allwinner,sun4i-a10-can"; + reg = <0x01c2bc00 0x400>; + interrupts = <0 26 4>; + clocks = <&apb1_gates 4>; + status = "disabled"; + }; + +Board specific .dts file: + + can0: can@01c2bc00 { + pinctrl-names = "default"; + pinctrl-0 = <&can0_pins_a>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index a9df21aaa154..4efca560adda 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -30,6 +30,13 @@ Optional properties: - dual_emac : Specifies Switch to act as Dual EMAC - syscon : Phandle to the system control device node, which is the control module device of the am33x +- mode-gpios : Should be added if one/multiple gpio lines are + required to be driven so that cpsw data lines + can be connected to the phy via selective mux. + For example in dra72x-evm, pcf gpio has to be + driven low so that cpsw slave 0 and phy data + lines are connected via mux. + Slave Properties: Required properties: @@ -39,6 +46,7 @@ Required properties: Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory +- phy-handle : See ethernet.txt file in the same directory Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index 1e97532a0b79..db74f0dc290c 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -57,6 +57,10 @@ Properties: "rgmii-id", as all other connection types are detected by hardware. - fsl,magic-packet : If present, indicates that the hardware supports waking up via magic packet. + - fsl,wake-on-filer : If present, indicates that the hardware supports + waking up by Filer General Purpose Interrupt (FGPI) asserted on the + Rx int line. This is an advanced power management capability allowing + certain packet types (user) defined by filer rules to wake up the system. - bd-stash : If present, indicates that the hardware supports stashing buffer descriptors in the L2. - rx-stash-len : Denotes the number of bytes of a received buffer to stash diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt index 988fc694b663..d1df8a00e1f3 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt @@ -32,13 +32,13 @@ Required properties: Required properties: -- compatible: should be "hisilicon,hip04-mdio". +- compatible: should be "hisilicon,mdio". - Inherits from MDIO bus node binding [2] [2] Documentation/devicetree/bindings/net/phy.txt Example: mdio { - compatible = "hisilicon,hip04-mdio"; + compatible = "hisilicon,mdio"; reg = <0x28f1000 0x1000>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt new file mode 100644 index 000000000000..80411b2f0490 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -0,0 +1,49 @@ +Hisilicon DSA Fabric device controller + +Required properties: +- compatible: should be "hisilicon,hns-dsaf-v1" or "hisilicon,hns-dsaf-v2". + "hisilicon,hns-dsaf-v1" is for hip05. + "hisilicon,hns-dsaf-v2" is for Hi1610 and Hi1612. +- dsa-name: dsa fabric name who provide this interface. + should be "dsafX", X is the dsaf id. +- mode: dsa fabric mode string. only support one of dsaf modes like these: + "2port-64vf", + "6port-16rss", + "6port-16vf". +- interrupt-parent: the interrupt parent of this device. +- interrupts: should contain the DSA Fabric and rcb interrupt. +- reg: specifies base physical address(es) and size of the device registers. + The first region is external interface control register base and size. + The second region is SerDes base register and size. + The third region is the PPE register base and size. + The fourth region is dsa fabric base register and size. + The fifth region is cpld base register and size, it is not required if do not use cpld. +- phy-handle: phy handle of physicl port, 0 if not any phy device. see ethernet.txt [1]. +- buf-size: rx buffer size, should be 16-1024. +- desc-num: number of description in TX and RX queue, should be 512, 1024, 2048 or 4096. + +[1] Documentation/devicetree/bindings/net/phy.txt + +Example: + +dsa: dsa@c7000000 { + compatible = "hisilicon,hns-dsaf-v1"; + dsa_name = "dsaf0"; + mode = "6port-16rss"; + interrupt-parent = <&mbigen_dsa>; + reg = <0x0 0xC0000000 0x0 0x420000 + 0x0 0xC2000000 0x0 0x300000 + 0x0 0xc5000000 0x0 0x890000 + 0x0 0xc7000000 0x0 0x60000>; + phy-handle = <0 0 0 0 &soc0_phy4 &soc0_phy5 0 0>; + interrupts = <131 4>,<132 4>, <133 4>,<134 4>, + <135 4>,<136 4>, <137 4>,<138 4>, + <139 4>,<140 4>, <141 4>,<142 4>, + <143 4>,<144 4>, <145 4>,<146 4>, + <147 4>,<148 4>, <384 1>,<385 1>, + <386 1>,<387 1>, <388 1>,<389 1>, + <390 1>,<391 1>, + buf-size = <4096>; + desc-num = <1024>; + dma-coherent; +}; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt new file mode 100644 index 000000000000..9c23fdf25018 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt @@ -0,0 +1,22 @@ +Hisilicon MDIO bus controller + +Properties: +- compatible: "hisilicon,mdio","hisilicon,hns-mdio". +- reg: The base address of the MDIO bus controller register bank. +- #address-cells: Must be <1>. +- #size-cells: Must be <0>. MDIO addresses have no size component. + +Typically an MDIO bus might have several children. + +Example: + mdio@803c0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "hisilicon,hns-mdio","hisilicon,mdio"; + reg = <0x0 0x803c0000 0x0 0x10000>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt new file mode 100644 index 000000000000..41d19be7011e --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt @@ -0,0 +1,47 @@ +Hisilicon Network Subsystem NIC controller + +Required properties: +- compatible: "hisilicon,hns-nic-v1" or "hisilicon,hns-nic-v2". + "hisilicon,hns-nic-v1" is for hip05. + "hisilicon,hns-nic-v2" is for Hi1610 and Hi1612. +- ae-name: accelerator name who provides this interface, + is simply a name referring to the name of name in the accelerator node. +- port-id: is the index of port provided by DSAF (the accelerator). DSAF can + connect to 8 PHYs. Port 0 to 1 are both used for adminstration purpose. They + are called debug ports. + + The remaining 6 PHYs are taken according to the mode of DSAF. + + In NIC mode of DSAF, all 6 PHYs are taken as ethernet ports to the CPU. The + port-id can be 2 to 7. Here is the diagram: + +-----+---------------+ + | CPU | + +-+-+-+---+-+-+-+-+-+-+ + | | | | | | | | + debug service + port port + (0,1) (2-7) + + In Switch mode of DSAF, all 6 PHYs are taken as physical ports connect to a + LAN Switch while the CPU side assume itself have one single NIC connect to + this switch. In this case, the port-id will be 2 only. + +-----+---------------+ + | CPU | + +-+-+-+---+-+-+-+-+-+-+ + | | service| port(2) + debug +------------+ + port | switch | + (0,1) +-+-+-+-+-+-++ + | | | | | | + external port + +- local-mac-address: mac addr of the ethernet interface + +Example: + + ethernet@0{ + compatible = "hisilicon,hns-nic-v1"; + ae-name = "dsaf0"; + port-id = <0>; + local-mac-address = [a2 14 e4 4b 56 76]; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt b/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt new file mode 100644 index 000000000000..a4ed2efb5b73 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt @@ -0,0 +1,20 @@ +* MRF24J40 IEEE 802.15.4 * + +Required properties: + - compatible: should be "microchip,mrf24j40", "microchip,mrf24j40ma", + or "microchip,mrf24j40mc" depends on your transceiver + board + - spi-max-frequency: maximal bus speed, should be set something under or equal + 10000000 + - reg: the chipselect index + - interrupts: the interrupt generated by the device. + +Example: + + mrf24j40ma@0 { + compatible = "microchip,mrf24j40ma"; + spi-max-frequency = <8500000>; + reg = <0>; + interrupts = <19 8>; + interrupt-parent = <&gpio3>; + }; diff --git a/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt index 7c4a0cc370cf..76df9173825a 100644 --- a/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt +++ b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt @@ -1,7 +1,10 @@ * Marvell International Ltd. NCI NFC Controller Required properties: -- compatible: Should be "mrvl,nfc-uart". +- compatible: Should be: + - "marvell,nfc-uart" or "mrvl,nfc-uart" for UART devices + - "marvell,nfc-i2c" for I2C devices + - "marvell,nfc-spi" for SPI devices Optional SoC specific properties: - pinctrl-names: Contains only one value - "default". @@ -13,13 +16,19 @@ Optional UART-based chip specific properties: - flow-control: Specifies that the chip is using RTS/CTS. - break-control: Specifies that the chip needs specific break management. +Optional I2C-based chip specific properties: +- i2c-int-falling: Specifies that the chip read event shall be trigged on + falling edge. +- i2c-int-rising: Specifies that the chip read event shall be trigged on + rising edge. + Example (for ARM-based BeagleBoard Black with 88W8887 on UART5): &uart5 { status = "okay"; nfcmrvluart: nfcmrvluart@5 { - compatible = "mrvl,nfc-uart"; + compatible = "marvell,nfc-uart"; reset-n-io = <&gpio3 16 0>; @@ -27,3 +36,51 @@ Example (for ARM-based BeagleBoard Black with 88W8887 on UART5): flow-control; } }; + + +Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1): + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + nfcmrvli2c0: i2c@1 { + compatible = "marvell,nfc-i2c"; + + reg = <0x8>; + + /* I2C INT configuration */ + interrupt-parent = <&gpio3>; + interrupts = <21 0>; + + /* I2C INT trigger configuration */ + i2c-int-rising; + + /* Reset IO */ + reset-n-io = <&gpio3 19 0>; + }; +}; + + +Example (for ARM-based BeagleBoard Black on SPI0): + +&spi0 { + + mrvlnfcspi0: spi@0 { + compatible = "marvell,nfc-spi"; + + reg = <0>; + + /* SPI Bus configuration */ + spi-max-frequency = <3000000>; + spi-cpha; + spi-cpol; + + /* SPI INT configuration */ + interrupt-parent = <&gpio1>; + interrupts = <17 0>; + + /* Reset IO */ + reset-n-io = <&gpio3 19 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt index d707588ed734..263732e8879f 100644 --- a/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt @@ -11,6 +11,10 @@ Required properties: Optional SoC Specific Properties: - pinctrl-names: Contains only one value - "default". - pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): @@ -29,5 +33,8 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; }; }; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt index 525681b6dc39..711ca85a363d 100644 --- a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt @@ -2,7 +2,7 @@ Required properties: - compatible: Should be "st,st21nfcb-spi" -- spi-max-frequency: Maximum SPI frequency (<= 10000000). +- spi-max-frequency: Maximum SPI frequency (<= 4000000). - interrupt-parent: phandle for the interrupt gpio controller - interrupts: GPIO interrupt to which the chip is connected - reset-gpios: Output GPIO pin used to reset the ST21NFCB @@ -10,6 +10,10 @@ Required properties: Optional SoC Specific Properties: - pinctrl-names: Contains only one value - "default". - pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4): @@ -27,5 +31,8 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4): interrupts = <2 IRQ_TYPE_EDGE_RISING>; reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; }; }; diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index 1fd8831437bf..b486f3f5f6a3 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -6,8 +6,12 @@ interface contains. Required properties: - compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC. "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC. + "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC. - reg: offset and length of (1) the register block and (2) the stream buffer. -- interrupts: interrupt specifier for the sole interrupt. +- interrupts: A list of interrupt-specifiers, one for each entry in + interrupt-names. + If interrupt-names is not present, an interrupt specifier + for a single muxed interrupt. - phy-mode: see ethernet.txt file in the same directory. - phy-handle: see ethernet.txt file in the same directory. - #address-cells: number of address cells for the MDIO bus, must be equal to 1. @@ -18,6 +22,12 @@ Required properties: Optional properties: - interrupt-parent: the phandle for the interrupt controller that services interrupts for this device. +- interrupt-names: A list of interrupt names. + For the R8A7795 SoC this property is mandatory; + it should include one entry per channel, named "ch%u", + where %u is the channel number ranging from 0 to 24. + For other SoCs this property is optional; if present + it should contain "mux" for a single muxed interrupt. - pinctrl-names: pin configuration state name ("default"). - renesas,no-ether-link: boolean, specify when a board does not provide a proper AVB_LINK signal. @@ -27,13 +37,46 @@ Optional properties: Example: ethernet@e6800000 { - compatible = "renesas,etheravb-r8a7790"; - reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>; + compatible = "renesas,etheravb-r8a7795"; + reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>; interrupt-parent = <&gic>; - interrupts = <0 163 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp8_clks R8A7790_CLK_ETHERAVB>; - phy-mode = "rmii"; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&mstp8_clks R8A7795_CLK_ETHERAVB>; + power-domains = <&cpg_clocks>; + phy-mode = "rgmii-id"; phy-handle = <&phy0>; + pinctrl-0 = <ðer_pins>; pinctrl-names = "default"; renesas,no-ether-link; @@ -41,8 +84,20 @@ Example: #size-cells = <0>; phy0: ethernet-phy@0 { + rxc-skew-ps = <900>; + rxdv-skew-ps = <0>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txc-skew-ps = <900>; + txen-skew-ps = <0>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; reg = <0>; interrupt-parent = <&gpio2>; - interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/Documentation/devicetree/bindings/net/smsc-lan87xx.txt b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt new file mode 100644 index 000000000000..974edd5c85cc --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt @@ -0,0 +1,24 @@ +SMSC LAN87xx Ethernet PHY + +Some boards require special tuning values. Configure them +through an Ethernet OF device node. + +Optional properties: + +- smsc,disable-energy-detect: + If set, do not enable energy detect mode for the SMSC phy. + default: enable energy detect mode + +Examples: +smsc phy with disabled energy detect mode on an am335x based board. +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; + + ethernetphy0: ethernet-phy@0 { + reg = <0>; + smsc,disable-energy-detect; + }; +}; diff --git a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt new file mode 100644 index 000000000000..383d5889e95a --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt @@ -0,0 +1,20 @@ +Freescale i.MX6 On-Chip OTP Controller (OCOTP) device tree bindings + +This binding represents the on-chip eFuse OTP controller found on +i.MX6Q/D, i.MX6DL/S, i.MX6SL, and i.MX6SX SoCs. + +Required properties: +- compatible: should be one of + "fsl,imx6q-ocotp" (i.MX6Q/D/DL/S), + "fsl,imx6sl-ocotp" (i.MX6SL), or + "fsl,imx6sx-ocotp" (i.MX6SX), followed by "syscon". +- reg: Should contain the register base and length. +- clocks: Should contain a phandle pointing to the gated peripheral clock. + +Example: + + ocotp: ocotp@021bc000 { + compatible = "fsl,imx6q-ocotp", "syscon"; + reg = <0x021bc000 0x4000>; + clocks = <&clks IMX6QDL_CLK_IIM>; + }; diff --git a/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt b/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt new file mode 100644 index 000000000000..daebce9e6b07 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt @@ -0,0 +1,25 @@ +On-Chip OTP Memory for Freescale i.MX23/i.MX28 + +Required properties : +- compatible : + - "fsl,imx23-ocotp" for i.MX23 + - "fsl,imx28-ocotp" for i.MX28 +- #address-cells : Should be 1 +- #size-cells : Should be 1 +- reg : Address and length of OTP controller registers +- clocks : Should contain a reference to the hbus clock + += Data cells = +Are child nodes of mxs-ocotp, bindings of which as described in +bindings/nvmem/nvmem.txt + +Example for i.MX28: + + ocotp: ocotp@8002c000 { + compatible = "fsl,imx28-ocotp", "fsl,ocotp"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x8002c000 0x2000>; + clocks = <&clks 25>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt new file mode 100644 index 000000000000..8f86ab3b1046 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt @@ -0,0 +1,38 @@ += Rockchip eFuse device tree bindings = + +Required properties: +- compatible: Should be "rockchip,rockchip-efuse" +- reg: Should contain the registers location and exact eFuse size +- clocks: Should be the clock id of eFuse +- clock-names: Should be "pclk_efuse" + += Data cells = +Are child nodes of eFuse, bindings of which as described in +bindings/nvmem/nvmem.txt + +Example: + + efuse: efuse@ffb40000 { + compatible = "rockchip,rockchip-efuse"; + reg = <0xffb40000 0x20>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&cru PCLK_EFUSE256>; + clock-names = "pclk_efuse"; + + /* Data cells */ + cpu_leakage: cpu_leakage { + reg = <0x17 0x1>; + }; + }; + += Data consumers = +Are device nodes which consume nvmem data cells. + +Example: + + cpu_leakage { + ... + nvmem-cells = <&cpu_leakage>; + nvmem-cell-names = "cpu_leakage"; + }; diff --git a/Documentation/devicetree/bindings/nvmem/vf610-ocotp.txt b/Documentation/devicetree/bindings/nvmem/vf610-ocotp.txt new file mode 100644 index 000000000000..56ed481c3e26 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/vf610-ocotp.txt @@ -0,0 +1,19 @@ +On-Chip OTP Memory for Freescale Vybrid + +Required Properties: + compatible: + - "fsl,vf610-ocotp" for VF5xx/VF6xx + #address-cells : Should be 1 + #size-cells : Should be 1 + reg : Address and length of OTP controller and fuse map registers + clocks : ipg clock we associate with the OCOTP peripheral + +Example for Vybrid VF5xx/VF6xx: + + ocotp: ocotp@400a5000 { + compatible = "fsl,vf610-ocotp"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x400a5000 0xCF0>; + clocks = <&clks VF610_CLK_OCOTP>; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-msi.txt b/Documentation/devicetree/bindings/pci/pci-msi.txt new file mode 100644 index 000000000000..9b3cc817d181 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-msi.txt @@ -0,0 +1,220 @@ +This document describes the generic device tree binding for describing the +relationship between PCI devices and MSI controllers. + +Each PCI device under a root complex is uniquely identified by its Requester ID +(AKA RID). A Requester ID is a triplet of a Bus number, Device number, and +Function number. + +For the purpose of this document, when treated as a numeric value, a RID is +formatted such that: + +* Bits [15:8] are the Bus number. +* Bits [7:3] are the Device number. +* Bits [2:0] are the Function number. +* Any other bits required for padding must be zero. + +MSIs may be distinguished in part through the use of sideband data accompanying +writes. In the case of PCI devices, this sideband data may be derived from the +Requester ID. A mechanism is required to associate a device with both the MSI +controllers it can address, and the sideband data that will be associated with +its writes to those controllers. + +For generic MSI bindings, see +Documentation/devicetree/bindings/interrupt-controller/msi.txt. + + +PCI root complex +================ + +Optional properties +------------------- + +- msi-map: Maps a Requester ID to an MSI controller and associated + msi-specifier data. The property is an arbitrary number of tuples of + (rid-base,msi-controller,msi-base,length), where: + + * rid-base is a single cell describing the first RID matched by the entry. + + * msi-controller is a single phandle to an MSI controller + + * msi-base is an msi-specifier describing the msi-specifier produced for the + first RID matched by the entry. + + * length is a single cell describing how many consecutive RIDs are matched + following the rid-base. + + Any RID r in the interval [rid-base, rid-base + length) is associated with + the listed msi-controller, with the msi-specifier (r - rid-base + msi-base). + +- msi-map-mask: A mask to be applied to each Requester ID prior to being mapped + to an msi-specifier per the msi-map property. + +- msi-parent: Describes the MSI parent of the root complex itself. Where + the root complex and MSI controller do not pass sideband data with MSI + writes, this property may be used to describe the MSI controller(s) + used by PCI devices under the root complex, if defined as such in the + binding for the root complex. + + +Example (1) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, identity-mapped. + */ + msi-map = <0x0 &msi_a 0x0 0x10000>, + }; +}; + + +Example (2) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, masked to only the device and function bits. + */ + msi-map = <0x0 &msi_a 0x0 0x100>, + msi-map-mask = <0xff> + }; +}; + + +Example (3) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, but the high bit of the bus number is + * ignored. + */ + msi-map = <0x0000 &msi 0x0000 0x8000>, + <0x8000 &msi 0x0000 0x8000>; + }; +}; + + +Example (4) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, but the high bit of the bus number is + * negated. + */ + msi-map = <0x0000 &msi 0x8000 0x8000>, + <0x8000 &msi 0x0000 0x8000>; + }; +}; + + +Example (5) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi_a: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + msi_b: msi-controller@b { + reg = <0xb 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + msi_c: msi-controller@c { + reg = <0xc 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@c { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to MSI controller a is the + * RID, but the high bit of the bus number is negated. + * The sideband data provided to MSI controller b is the + * RID, identity-mapped. + * MSI controller c is not addressable. + */ + msi-map = <0x0000 &msi_a 0x8000 0x08000>, + <0x8000 &msi_a 0x0000 0x08000>, + <0x0000 &msi_b 0x0000 0x10000>; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index d8ef5bf50f11..7fab84b33531 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -7,7 +7,8 @@ OHCI and EHCI controllers. Required properties: - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC; - "renesas,pci-r8a7791" for the R8A7791 SoC. + "renesas,pci-r8a7791" for the R8A7791 SoC; + "renesas,pci-r8a7794" for the R8A7794 SoC. - reg: A list of physical regions to access the device: the first is the operational registers for the OHCI/EHCI controllers and the second is for the bridge configuration and control registers. diff --git a/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt b/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt new file mode 100644 index 000000000000..761c4bc24a9b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt @@ -0,0 +1,47 @@ +Broadcom Cygnus PCIe PHY + +Required properties: +- compatible: must be "brcm,cygnus-pcie-phy" +- reg: base address and length of the PCIe PHY block +- #address-cells: must be 1 +- #size-cells: must be 0 + +Each PCIe PHY should be represented by a child node + +Required properties For the child node: +- reg: the PHY ID +0 - PCIe RC 0 +1 - PCIe RC 1 +- #phy-cells: must be 0 + +Example: + pcie_phy: phy@0301d0a0 { + compatible = "brcm,cygnus-pcie-phy"; + reg = <0x0301d0a0 0x14>; + + pcie0_phy: phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + pcie1_phy: phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; + + /* users of the PCIe phy */ + + pcie0: pcie@18012000 { + ... + ... + phys = <&pcie0_phy>; + phy-names = "pcie-phy"; + }; + + pcie1: pcie@18013000 { + ... + ... + phys = <pcie1_phy>; + phy-names = "pcie-phy"; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file mode 100644 index 000000000000..00100cf3e037 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt @@ -0,0 +1,68 @@ +mt65xx USB3.0 PHY binding +-------------------------- + +This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. + +Required properties (controller (parent) node): + - compatible : should be "mediatek,mt8173-u3phy" + - reg : offset and length of register for phy, exclude port's + register. + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain + "u3phya_ref": for reference clock of usb3.0 analog phy. + +Required nodes : a sub-node is required for each port the controller + provides. Address range information including the usual + 'reg' property is used inside these nodes to describe + the controller's topology. + +Required properties (port (child) node): +- reg : address and length of the register set for the port. +- #phy-cells : should be 1 (See second example) + cell after port phandle is phy type from: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + +Example: + +u3phy: usb-phy@11290000 { + compatible = "mediatek,mt8173-u3phy"; + reg = <0 0x11290000 0 0x800>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; + clock-names = "u3phya_ref"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "okay"; + + phy_port0: port@11290800 { + reg = <0 0x11290800 0 0x800>; + #phy-cells = <1>; + status = "okay"; + }; + + phy_port1: port@11291000 { + reg = <0 0x11291000 0 0x800>; + #phy-cells = <1>; + status = "okay"; + }; +}; + +Specifying phy control of devices +--------------------------------- + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the phy port node and a device type; +phy-names for each port are optional. + +Example: + +#include <dt-bindings/phy/phy.h> + +usb30: usb@11270000 { + ... + phys = <&phy_port0 PHY_TYPE_USB3>; + phy-names = "usb3-0"; + ... +}; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index 60c6f2a633e0..0289d3b07853 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -44,6 +44,9 @@ Required properties: - the "ref" clock is used to get the rate of the clock provided to the PHY module +Optional properties: +- vbus-supply: power-supply phandle for vbus power source + The first phandle argument in the PHY specifier identifies the PHY, its meaning is compatible dependent. For the currently supported SoCs (Exynos 4210 and Exynos 4212) it is as follows: diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 3c821cda1ad0..b321b26780dc 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -17,6 +17,7 @@ Required properties: "allwinner,sun8i-a23-pinctrl" "allwinner,sun8i-a23-r-pinctrl" "allwinner,sun8i-a33-pinctrl" + "allwinner,sun8i-a83t-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt new file mode 100644 index 000000000000..61ac75706cc9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt @@ -0,0 +1,90 @@ +* Atmel PIO4 Controller + +The Atmel PIO4 controller is used to select the function of a pin and to +configure it. + +Required properties: +- compatible: "atmel,sama5d2-pinctrl". +- reg: base address and length of the PIO controller. +- interrupts: interrupt outputs from the controller, one for each bank. +- interrupt-controller: mark the device node as an interrupt controller. +- #interrupt-cells: should be two. +- gpio-controller: mark the device node as a gpio controller. +- #gpio-cells: should be two. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. + +Subnode format +Each node (or subnode) will list the pins it needs and how to configured these +pins. + + node { + pinmux = <PIN_NUMBER_PINMUX>; + GENERIC_PINCONFIG; + }; + +Required properties: +- pinmux: integer array. Each integer represents a pin number plus mux and +ioset settings. Use the macros from boot/dts/<soc>-pinfunc.h file to get the +right representation of the pin. + +Optional properties: +- GENERIC_PINCONFIG: generic pinconfig options to use, bias-disable, +bias-pull-down, bias-pull-up, drive-open-drain, input-schmitt-enable, +input-debounce, output-low, output-high. + +Example: + +#include <sama5d2-pinfunc.h> + +... +{ + pioA: pinctrl@fc038000 { + compatible = "atmel,sama5d2-pinctrl"; + reg = <0xfc038000 0x600>; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH 7>, + <68 IRQ_TYPE_LEVEL_HIGH 7>, + <69 IRQ_TYPE_LEVEL_HIGH 7>, + <70 IRQ_TYPE_LEVEL_HIGH 7>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + clocks = <&pioA_clk>; + + pinctrl_i2c0_default: i2c0_default { + pinmux = <PIN_PD21__TWD0>, + <PIN_PD22__TWCK0>; + bias-disable; + }; + + pinctrl_led_gpio_default: led_gpio_default { + pinmux = <PIN_PB0>, + <PIN_PB5>; + bias-pull-up; + }; + + pinctrl_sdmmc1_default: sdmmc1_default { + cmd_data { + pinmux = <PIN_PA28__SDMMC1_CMD>, + <PIN_PA18__SDMMC1_DAT0>, + <PIN_PA19__SDMMC1_DAT1>, + <PIN_PA20__SDMMC1_DAT2>, + <PIN_PA21__SDMMC1_DAT3>; + bias-pull-up; + }; + + ck_cd { + pinmux = <PIN_PA22__SDMMC1_CK>, + <PIN_PA30__SDMMC1_CD>; + bias-disable; + }; + }; + ... + }; +}; +... diff --git a/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt index a8bb5e26019c..f8fa28ce163e 100644 --- a/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt @@ -20,7 +20,10 @@ Required properties: "marvell,berlin2cd-soc-pinctrl", "marvell,berlin2cd-system-pinctrl", "marvell,berlin2q-soc-pinctrl", - "marvell,berlin2q-system-pinctrl" + "marvell,berlin2q-system-pinctrl", + "marvell,berlin4ct-avio-pinctrl", + "marvell,berlin4ct-soc-pinctrl", + "marvell,berlin4ct-system-pinctrl" Required subnode-properties: - groups: a list of strings describing the group names. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt index 6540ca56be5e..16589fb6f420 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt @@ -3,8 +3,8 @@ Broadcom Cygnus GPIO/PINCONF Controller Required properties: - compatible: - Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or - "brcm,cygnus-crmu-gpio" + Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", + "brcm,cygnus-crmu-gpio" or "brcm,iproc-gpio" - reg: Define the base and range of the I/O address space that contains the Cygnus @@ -26,9 +26,13 @@ Optional properties: - interrupt-controller: Specifies that the node is an interrupt controller -- pinmux: - Specifies the phandle to the IOMUX device, where pins can be individually -muxed to GPIO +- gpio-ranges: + Specifies the mapping between gpio controller and pin-controllers pins. + This requires 4 fields in cells defined as - + 1. Phandle of pin-controller. + 2. GPIO base pin offset. + 3 Pin-control base pin offset. + 4. number of gpio pins which are linearly mapped from pin base. Supported generic PINCONF properties in child nodes: @@ -78,6 +82,8 @@ Example: gpio-controller; interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; + gpio-ranges = <&pinctrl 0 42 1>, + <&pinctrl 1 44 3>; }; /* diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt index 8bbf25d58656..457b2c68d47b 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt @@ -1,16 +1,42 @@ * Freescale i.MX7 Dual IOMUX Controller +iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar +as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low +power state retention capabilities on gpios that are part of iomuxc-lpsr +(GPIO1_IO7..GPIO1_IO0). While iomuxc-lpsr provides its own set of registers for +mux and pad control settings, it shares the input select register from main +iomuxc controller for daisy chain settings, the fsl,input-sel property extends +fsl,imx-pinctrl driver to support iomuxc-lpsr controller. + +iomuxc_lpsr: iomuxc-lpsr@302c0000 { + compatible = "fsl,imx7d-iomuxc-lpsr"; + reg = <0x302c0000 0x10000>; + fsl,input-sel = <&iomuxc>; +}; + +iomuxc: iomuxc@30330000 { + compatible = "fsl,imx7d-iomuxc"; + reg = <0x30330000 0x10000>; +}; + +Pheriparials using pads from iomuxc-lpsr support low state retention power +state, under LPSR mode GPIO's state of pads are retain. + Please refer to fsl,imx-pinctrl.txt in this directory for common binding part and usage. Required properties: -- compatible: "fsl,imx7d-iomuxc" +- compatible: "fsl,imx7d-iomuxc" for main IOMUXC controller, or + "fsl,imx7d-iomuxc-lpsr" for Low Power State Retention IOMUXC controller. - fsl,pins: each entry consists of 6 integers and represents the mux and config setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val input_val> are specified using a PIN_FUNC_ID macro, which can be found in imx7d-pinfunc.h under device tree source folder. The last integer CONFIG is the pad setting value like pull-up on this pin. Please refer to i.MX7 Dual Reference Manual for detailed CONFIG settings. +- fsl,input-sel: required property for iomuxc-lpsr controller, this property is + a phandle for main iomuxc controller which shares the input select register for + daisy chain settings. CONFIG bits definition: PAD_CTL_PUS_100K_DOWN (0 << 5) @@ -25,3 +51,38 @@ PAD_CTL_DSE_X1 (0 << 0) PAD_CTL_DSE_X2 (1 << 0) PAD_CTL_DSE_X3 (2 << 0) PAD_CTL_DSE_X4 (3 << 0) + +Examples: +While iomuxc-lpsr is intended to be used by dedicated peripherals to take +advantages of LPSR power mode, is also possible that an IP to use pads from +any of the iomux controllers. For example the I2C1 IP can use SCL pad from +iomuxc-lpsr controller and SDA pad from iomuxc controller as: + +i2c1: i2c@30a20000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>; + status = "okay"; +}; + +iomuxc-lpsr@302c0000 { + compatible = "fsl,imx7d-iomuxc-lpsr"; + reg = <0x302c0000 0x10000>; + fsl,input-sel = <&iomuxc>; + + pinctrl_i2c1_1: i2c1grp-1 { + fsl,pins = < + MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f + >; + }; +}; + +iomuxc@30330000 { + compatible = "fsl,imx7d-iomuxc"; + reg = <0x30330000 0x10000>; + + pinctrl_i2c1_2: i2c1grp-2 { + fsl,pins = < + MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f + >; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 9496934528bd..ffadb7a371f6 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -19,6 +19,7 @@ Required Properties: - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2-W) compatible pin-controller. - "renesas,pfc-r8a7793": for R8A7793 (R-Car M2-N) compatible pin-controller. - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller. + - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. - reg: Base address and length of each memory resource used by the pin diff --git a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt index 32aa26f1e434..acbcb452a69a 100644 --- a/Documentation/devicetree/bindings/regulator/pbias-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pbias-regulator.txt @@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs. Required properties: - compatible: - - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7. + - should be "ti,pbias-dra7" for DRA7 + - should be "ti,pbias-omap2" for OMAP2 + - should be "ti,pbias-omap3" for OMAP3 + - should be "ti,pbias-omap4" for OMAP4 + - should be "ti,pbias-omap5" for OMAP5 + - "ti,pbias-omap" is deprecated - reg: pbias register offset from syscon base and size of pbias register. - syscon : phandle of the system control module - regulator-name : should be diff --git a/Documentation/devicetree/bindings/rng/samsung,exynos-rng4.txt b/Documentation/devicetree/bindings/rng/samsung,exynos-rng4.txt new file mode 100644 index 000000000000..4ca8dd4d7e66 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/samsung,exynos-rng4.txt @@ -0,0 +1,17 @@ +Exynos Pseudo Random Number Generator + +Required properties: + +- compatible : Should be "samsung,exynos4-rng". +- reg : Specifies base physical address and size of the registers map. +- clocks : Phandle to clock-controller plus clock-specifier pair. +- clock-names : "secss" as a clock name. + +Example: + + rng@10830400 { + compatible = "samsung,exynos4-rng"; + reg = <0x10830400 0x200>; + clocks = <&clock CLK_SSS>; + clock-names = "secss"; + }; diff --git a/Documentation/devicetree/bindings/rng/st,rng.txt b/Documentation/devicetree/bindings/rng/st,rng.txt new file mode 100644 index 000000000000..35734bc282e9 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/st,rng.txt @@ -0,0 +1,15 @@ +STMicroelectronics HW Random Number Generator +---------------------------------------------- + +Required parameters: +compatible : Should be "st,rng" +reg : Base address and size of IP's register map. +clocks : Phandle to device's clock (See: ../clocks/clock-bindings.txt) + +Example: + +rng@fee80000 { + compatible = "st,rng"; + reg = <0xfee80000 0x1000>; + clocks = <&clk_sysin>; +} diff --git a/Documentation/devicetree/bindings/rng/st,stm32-rng.txt b/Documentation/devicetree/bindings/rng/st,stm32-rng.txt new file mode 100644 index 000000000000..47f04176f93b --- /dev/null +++ b/Documentation/devicetree/bindings/rng/st,stm32-rng.txt @@ -0,0 +1,21 @@ +STMicroelectronics STM32 HW RNG +=============================== + +The STM32 hardware random number generator is a simple fixed purpose IP and +is fully separated from other crypto functions. + +Required properties: + +- compatible : Should be "st,stm32-rng" +- reg : Should be register base and length as documented in the datasheet +- interrupts : The designated IRQ line for the RNG +- clocks : The clock needed to enable the RNG + +Example: + + rng: rng@50060800 { + compatible = "st,stm32-rng"; + reg = <0x50060800 0x400>; + interrupts = <80>; + clocks = <&rcc 0 38>; + }; diff --git a/Documentation/devicetree/bindings/serial/ingenic,uart.txt b/Documentation/devicetree/bindings/serial/ingenic,uart.txt index c2d3b3abe7d9..02cb7fe59cb7 100644 --- a/Documentation/devicetree/bindings/serial/ingenic,uart.txt +++ b/Documentation/devicetree/bindings/serial/ingenic,uart.txt @@ -1,7 +1,8 @@ * Ingenic SoC UART Required properties: -- compatible : "ingenic,jz4740-uart" or "ingenic,jz4780-uart" +- compatible : "ingenic,jz4740-uart", "ingenic,jz4760-uart", + "ingenic,jz4775-uart" or "ingenic,jz4780-uart" - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. - clocks : phandles to the module & baud clocks. diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt index cbae3d9a0278..77863aefe9ef 100644 --- a/Documentation/devicetree/bindings/serial/pl011.txt +++ b/Documentation/devicetree/bindings/serial/pl011.txt @@ -19,7 +19,7 @@ Optional properties: must correspond to the PCLK clocking the internal logic of the block. Just listing one clock (the first one) is deprecated. -- clocks-names: +- clock-names: When present, the first clock listed must be named "uartclk" and the second clock listed must be named "apb_pclk" diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt index a2114c217376..182777fac9a2 100644 --- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt @@ -26,6 +26,12 @@ Required properties: Optional properties: - dmas: Should contain dma specifiers for transmit and receive channels - dma-names: Should contain "tx" for transmit and "rx" for receive channels +- qcom,tx-crci: Identificator <u32> for Client Rate Control Interface to be + used with TX DMA channel. Required when using DMA for transmission + with UARTDM v1.3 and bellow. +- qcom,rx-crci: Identificator <u32> for Client Rate Control Interface to be + used with RX DMA channel. Required when using DMA for reception + with UARTDM v1.3 and bellow. Note: Aliases may be defined to ensure the correct ordering of the UARTs. The alias serialN will result in the UART being assigned port N. If any diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index e84b13a8eda3..73f825e5e644 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -23,6 +23,8 @@ Required properties: - "renesas,scifa-r8a7794" for R8A7794 (R-Car E2) SCIFA compatible UART. - "renesas,scifb-r8a7794" for R8A7794 (R-Car E2) SCIFB compatible UART. - "renesas,hscif-r8a7794" for R8A7794 (R-Car E2) HSCIF compatible UART. + - "renesas,scif-r8a7795" for R8A7795 (R-Car H3) SCIF compatible UART. + - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - "renesas,scif" for generic SCIF compatible UART. diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt index 289c40ed7470..12bbe9f22560 100644 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt @@ -15,6 +15,9 @@ The supplying peripheral clock can also be handled, needing a second property Required elements: "baudclk", "apb_pclk" Optional properties: +- snps,uart-16550-compatible : reflects the value of UART_16550_COMPATIBLE + configuration parameter. Define this if your UART does not implement the busy + functionality. - resets : phandle to the parent reset controller. - reg-shift : quantity to shift the register offsets by. If this property is not present then the register offsets are not shifted. diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 8f771441be60..705075da2f10 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -51,7 +51,7 @@ Optional properties, deprecated for soctype-specific bindings: - renesas,tx-fifo-size : Overrides the default tx fifo size given in words (default is 64) - renesas,rx-fifo-size : Overrides the default rx fifo size given in words - (default is 64, or 256 on R-Car Gen2) + (default is 64) Pinctrl properties might be needed, too. See Documentation/devicetree/bindings/pinctrl/renesas,*. diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index dcefc438272f..6160ffbcb3d3 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -15,17 +15,18 @@ Required properties: - interrupts: Should contain spi interrupt - clocks: phandles to input clocks. - The first should be <&topckgen CLK_TOP_SPI_SEL>. - The second should be one of the following. + The first should be one of the following. It's PLL. - <&clk26m>: specify parent clock 26MHZ. - <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ. It's the default one. - <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ. - <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ. - <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ. + The second should be <&topckgen CLK_TOP_SPI_SEL>. It's clock mux. + The third is <&pericfg CLK_PERI_SPI0>. It's clock gate. -- clock-names: shall be "spi-clk" for the controller clock, and - "parent-clk" for the parent clock. +- clock-names: shall be "parent-clk" for the parent clock, "sel-clk" for the + muxes clock, and "spi-clk" for the clock gate. Optional properties: - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi @@ -44,8 +45,11 @@ spi: spi@1100a000 { #size-cells = <0>; reg = <0 0x1100a000 0 0x1000>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>; - clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>; - clock-names = "spi-clk", "parent-clk"; + clocks = <&topckgen CLK_TOP_SYSPLL3_D2>, + <&topckgen CLK_TOP_SPI_SEL>, + <&pericfg CLK_PERI_SPI0>; + clock-names = "parent-clk", "sel-clk", "spi-clk"; + mediatek,pad-select = <0>; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 8a49362dea6e..41b817f7b670 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to the different fan speeds possible. Cooling states are referred to by single unsigned integers, where larger numbers mean greater heat dissipation. The precise set of cooling states associated with a device -(as referred to be the cooling-min-state and cooling-max-state +(as referred to by the cooling-min-level and cooling-max-level properties) should be defined in a particular device's binding. For more examples of cooling devices, refer to the example sections below. Required properties: -- cooling-min-state: An integer indicating the smallest - Type: unsigned cooling state accepted. Typically 0. - Size: one cell - -- cooling-max-state: An integer indicating the largest - Type: unsigned cooling state accepted. - Size: one cell - - #cooling-cells: Used to provide cooling device specific information Type: unsigned while referring to it. Must be at least 2, in order Size: one cell to specify minimum and maximum cooling state used @@ -77,6 +69,15 @@ Required properties: See Cooling device maps section below for more details on how consumers refer to cooling devices. +Optional properties: +- cooling-min-level: An integer indicating the smallest + Type: unsigned cooling state accepted. Typically 0. + Size: one cell + +- cooling-max-level: An integer indicating the largest + Type: unsigned cooling state accepted. + Size: one cell + * Trip points The trip node is a node to describe a point in the temperature domain @@ -225,8 +226,8 @@ cpus { 396000 950000 198000 850000 >; - cooling-min-state = <0>; - cooling-max-state = <3>; + cooling-min-level = <0>; + cooling-max-level = <3>; #cooling-cells = <2>; /* min followed by max */ }; ... @@ -240,8 +241,8 @@ cpus { */ fan0: fan@0x48 { ... - cooling-min-state = <0>; - cooling-max-state = <9>; + cooling-min-level = <0>; + cooling-max-level = <9>; #cooling-cells = <2>; /* min followed by max */ }; }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index d71ef07bca5d..781296bfbe4f 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -6,6 +6,7 @@ Required properties: "lsi,zevio-usb" "qcom,ci-hdrc" "chipidea,usb2" + "xlnx,zynq-usb-2.20a" - reg: base address and length of the registers - interrupts: interrupt for the USB controller @@ -26,10 +27,6 @@ Optional properties: - vbus-supply: reference to the VBUS regulator - maximum-speed: limit the maximum connection speed to "full-speed". - tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts -- fsl,usbmisc: (FSL only) phandler of non-core register device, with one - argument that indicate usb controller index -- disable-over-current: (FSL only) disable over current detect -- external-vbus-divider: (FSL only) enables off-chip resistor divider for Vbus - itc-setting: interrupt threshold control register control, the setting should be aligned with ITC bits at register USBCMD. - ahb-burst-config: it is vendor dependent, the required value should be @@ -40,11 +37,28 @@ Optional properties: - tx-burst-size-dword: it is vendor dependent, the tx burst size in dword (4 bytes), This register represents the maximum length of a the burst in 32-bit words while moving data from system memory to the USB - bus, changing this value takes effect only the SBUSCFG.AHBBRST is 0. + bus, the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. - rx-burst-size-dword: it is vendor dependent, the rx burst size in dword (4 bytes), This register represents the maximum length of a the burst in 32-bit words while moving data from the USB bus to system memory, - changing this value takes effect only the SBUSCFG.AHBBRST is 0. + the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. +- extcon: phandles to external connector devices. First phandle should point to + external connector, which provide "USB" cable events, the second should point + to external connector device, which provide "USB-HOST" cable events. If one + of the external connector devices is not required, empty <0> phandle should + be specified. +- phy-clkgate-delay-us: the delay time (us) between putting the PHY into + low power mode and gating the PHY clock. + +i.mx specific properties +- fsl,usbmisc: phandler of non-core register device, with one + argument that indicate usb controller index +- disable-over-current: disable over current detect +- external-vbus-divider: enables off-chip resistor divider for Vbus Example: @@ -61,4 +75,6 @@ Example: ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; + phy-clkgate-delay-us = <400>; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 0815eac5b185..9ff48e0defb4 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -35,11 +35,16 @@ Optional properties: LTSSM during USB3 Compliance mode. - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy. - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. + - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, + disabling the suspend signal to the PHY. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3. + - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ + register for post-silicon frame length adjustment when the + fladj_30mhz_sdbnd signal is invalid or incorrect. This is usually a subnode to DWC3 glue to which it is connected. diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 64a4ca6cf96f..7d48f63db44e 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -5,6 +5,7 @@ Required properties: - "renesas,usbhs-r8a7790" - "renesas,usbhs-r8a7791" - "renesas,usbhs-r8a7794" + - "renesas,usbhs-r8a7795" - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - clocks: A list of phandle + clock specifier pairs diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ac5f0c34ae00..13e54a0e78b9 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -101,6 +101,7 @@ himax Himax Technologies, Inc. hisilicon Hisilicon Limited. hit Hitachi Ltd. hitex Hitex Development Tools +holt Holt Integrated Circuits, Inc. honeywell Honeywell hp Hewlett Packard i2se I2SE GmbH @@ -169,6 +170,7 @@ phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd plathome Plat'Home Co., Ltd. pixcir PIXCIR MICROELECTRONICS Co., Ltd +pulsedlight PulsedLight, Inc powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc @@ -191,6 +193,7 @@ sbs Smart Battery System schindler Schindler seagate Seagate Technology PLC semtech Semtech Corporation +sgx SGX Sensortech sharp Sharp Corporation sil Silicon Image silabs Silicon Laboratories @@ -203,6 +206,7 @@ sitronix Sitronix Technology Corporation skyworks Skyworks Solutions, Inc. smsc Standard Microsystems Corporation snps Synopsys, Inc. +socionext Socionext Inc. solidrun SolidRun solomon Solomon Systech Limited sony Sony Corporation @@ -222,6 +226,7 @@ toshiba Toshiba Corporation toumaz Toumaz tplink TP-LINK Technologies Co., Ltd. truly Truly Semiconductors Limited +upisemi uPI Semiconductor Corp. usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor variscite Variscite Ltd. diff --git a/Documentation/devicetree/bindings/w1/omap-hdq.txt b/Documentation/devicetree/bindings/w1/omap-hdq.txt index fef794741bd1..913c5f91a0f9 100644 --- a/Documentation/devicetree/bindings/w1/omap-hdq.txt +++ b/Documentation/devicetree/bindings/w1/omap-hdq.txt @@ -1,11 +1,15 @@ * OMAP HDQ One wire bus master controller Required properties: -- compatible : should be "ti,omap3-1w" +- compatible : should be "ti,omap3-1w" or "ti,am4372-hdq" - reg : Address and length of the register set for the device - interrupts : interrupt line. - ti,hwmods : "hdq1w" +Optional properties: +- ti,mode: should be "hdq": HDQ mode "1w": one-wire mode. + If not specified HDQ mode is implied. + Example: - From omap3.dtsi @@ -14,4 +18,5 @@ Example: reg = <0x480b2000 0x1000>; interrupts = <58>; ti,hwmods = "hdq1w"; + ti,mode = "hdq"; }; |