diff options
Diffstat (limited to 'Documentation/devicetree')
57 files changed, 1259 insertions, 103 deletions
diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt index 6888a5efc860..c0105de55cbd 100644 --- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt +++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt @@ -6,6 +6,7 @@ provided by Arteris. Required properties: - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family Should be "ti,omap4-l3-noc" for OMAP4 family +- reg: Contains L3 register address range for each noc domain. - ti,hwmods: "l3_main_1", ... One hwmod for each noc domain. Examples: diff --git a/Documentation/devicetree/bindings/arm/omap/timer.txt b/Documentation/devicetree/bindings/arm/omap/timer.txt index 8732d4d41f8b..d02e27c764ec 100644 --- a/Documentation/devicetree/bindings/arm/omap/timer.txt +++ b/Documentation/devicetree/bindings/arm/omap/timer.txt @@ -1,7 +1,20 @@ OMAP Timer bindings Required properties: -- compatible: Must be "ti,omap2-timer" for OMAP2+ controllers. +- compatible: Should be set to one of the below. Please note that + OMAP44xx devices have timer instances that are 100% + register compatible with OMAP3xxx devices as well as + newer timers that are not 100% register compatible. + So for OMAP44xx devices timer instances may use + different compatible strings. + + ti,omap2420-timer (applicable to OMAP24xx devices) + ti,omap3430-timer (applicable to OMAP3xxx/44xx devices) + ti,omap4430-timer (applicable to OMAP44xx devices) + ti,omap5430-timer (applicable to OMAP543x devices) + ti,am335x-timer (applicable to AM335x devices) + ti,am335x-timer-1ms (applicable to AM335x devices) + - reg: Contains timer register address range (base address and length). - interrupts: Contains the interrupt information for the timer. The @@ -22,7 +35,7 @@ Optional properties: Example: timer12: timer@48304000 { - compatible = "ti,omap2-timer"; + compatible = "ti,omap3430-timer"; reg = <0x48304000 0x400>; interrupts = <95>; ti,hwmods = "timer12" diff --git a/Documentation/devicetree/bindings/arm/primecell.txt b/Documentation/devicetree/bindings/arm/primecell.txt index 64fc82bc8928..0df6acacfaea 100644 --- a/Documentation/devicetree/bindings/arm/primecell.txt +++ b/Documentation/devicetree/bindings/arm/primecell.txt @@ -16,14 +16,31 @@ Optional properties: - clocks : From common clock binding. First clock is phandle to clock for apb pclk. Additional clocks are optional and specific to those peripherals. - clock-names : From common clock binding. Shall be "apb_pclk" for first clock. +- dmas : From common DMA binding. If present, refers to one or more dma channels. +- dma-names : From common DMA binding, needs to match the 'dmas' property. + Devices with exactly one receive and transmit channel shall name + these "rx" and "tx", respectively. +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt +- pinctrl-names : Names corresponding to the numbered pinctrl states +- interrupts : one or more interrupt specifiers +- interrupt-names : names corresponding to the interrupts properties Example: serial@fff36000 { compatible = "arm,pl011", "arm,primecell"; arm,primecell-periphid = <0x00341011>; + clocks = <&pclk>; clock-names = "apb_pclk"; - + + dmas = <&dma-controller 4>, <&dma-controller 5>; + dma-names = "rx", "tx"; + + pinctrl-0 = <&uart0_default_mux>, <&uart0_default_mode>; + pinctrl-1 = <&uart0_sleep_mode>; + pinctrl-names = "default","sleep"; + + interrupts = <0 11 0x4>; }; diff --git a/Documentation/devicetree/bindings/arm/samsung/sysreg.txt b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt new file mode 100644 index 000000000000..5039c0a12f55 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt @@ -0,0 +1,7 @@ +SAMSUNG S5P/Exynos SoC series System Registers (SYSREG) + +Properties: + - name : should be 'sysreg'; + - compatible : should contain "samsung,<chip name>-sysreg", "syscon"; + For Exynos4 SoC series it should be "samsung,exynos4-sysreg", "syscon"; + - reg : offset and length of the register set. diff --git a/Documentation/devicetree/bindings/ata/pata-arasan.txt b/Documentation/devicetree/bindings/ata/pata-arasan.txt index 95ec7f825ede..2aff154be84e 100644 --- a/Documentation/devicetree/bindings/ata/pata-arasan.txt +++ b/Documentation/devicetree/bindings/ata/pata-arasan.txt @@ -6,6 +6,26 @@ Required properties: - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - interrupt: Should contain the CF interrupt number +- clock-frequency: Interface clock rate, in Hz, one of + 25000000 + 33000000 + 40000000 + 50000000 + 66000000 + 75000000 + 100000000 + 125000000 + 150000000 + 166000000 + 200000000 + +Optional properties: +- arasan,broken-udma: if present, UDMA mode is unusable +- arasan,broken-mwdma: if present, MWDMA mode is unusable +- arasan,broken-pio: if present, PIO mode is unusable +- dmas: one DMA channel, as described in bindings/dma/dma.txt + required unless both UDMA and MWDMA mode are broken +- dma-names: the corresponding channel name, must be "data" Example: @@ -14,4 +34,6 @@ Example: reg = <0xfc000000 0x1000>; interrupt-parent = <&vic1>; interrupts = <12>; + dmas = <&dma-controller 23>; + dma-names = "data"; }; diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt index 2a0c904c46ae..d71b4b2c077d 100644 --- a/Documentation/devicetree/bindings/clock/imx5-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx5-clock.txt @@ -38,7 +38,6 @@ clocks and IDs. usb_phy_podf 23 cpu_podf 24 di_pred 25 - tve_di 26 tve_s 27 uart1_ipg_gate 28 uart1_per_gate 29 @@ -172,6 +171,19 @@ clocks and IDs. can1_serial_gate 157 can1_ipg_gate 158 owire_gate 159 + gpu3d_s 160 + gpu2d_s 161 + gpu3d_gate 162 + gpu2d_gate 163 + garb_gate 164 + cko1_sel 165 + cko1_podf 166 + cko1 167 + cko2_sel 168 + cko2_podf 169 + cko2 170 + srtc_gate 171 + pata_gate 172 Examples (for mx53): diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt index 969b38e06ad3..6deb6fd1c7cd 100644 --- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -205,6 +205,9 @@ clocks and IDs. enet_ref 190 usbphy1_gate 191 usbphy2_gate 192 + pll4_post_div 193 + pll5_post_div 194 + pll5_video_div 195 Examples: diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt index 3c046ee6e8b5..c80e8a3402f0 100644 --- a/Documentation/devicetree/bindings/dma/atmel-dma.txt +++ b/Documentation/devicetree/bindings/dma/atmel-dma.txt @@ -1,14 +1,39 @@ * Atmel Direct Memory Access Controller (DMA) Required properties: -- compatible: Should be "atmel,<chip>-dma" -- reg: Should contain DMA registers location and length -- interrupts: Should contain DMA interrupt +- compatible: Should be "atmel,<chip>-dma". +- reg: Should contain DMA registers location and length. +- interrupts: Should contain DMA interrupt. +- #dma-cells: Must be <2>, used to represent the number of integer cells in +the dmas property of client devices. -Examples: +Example: -dma@ffffec00 { +dma0: dma@ffffec00 { compatible = "atmel,at91sam9g45-dma"; reg = <0xffffec00 0x200>; interrupts = <21>; + #dma-cells = <2>; +}; + +DMA clients connected to the Atmel DMA controller must use the format +described in the dma.txt file, using a three-cell specifier for each channel: +a phandle plus two interger cells. +The three cells in order are: + +1. A phandle pointing to the DMA controller. +2. The memory interface (16 most significant bits), the peripheral interface +(16 less significant bits). +3. The peripheral identifier for the hardware handshaking interface. The +identifier can be different for tx and rx. + +Example: + +i2c0@i2c@f8010000 { + compatible = "atmel,at91sam9x5-i2c"; + reg = <0xf8010000 0x100>; + interrupts = <9 4 6>; + dmas = <&dma0 1 7>, + <&dma0 1 8>; + dma-names = "tx", "rx"; }; diff --git a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt index ded0398d3bdc..a4873e5e3e36 100644 --- a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt @@ -3,17 +3,58 @@ Required properties: - compatible : Should be "fsl,<chip>-dma-apbh" or "fsl,<chip>-dma-apbx" - reg : Should contain registers location and length +- interrupts : Should contain the interrupt numbers of DMA channels. + If a channel is empty/reserved, 0 should be filled in place. +- #dma-cells : Must be <1>. The number cell specifies the channel ID. +- dma-channels : Number of channels supported by the DMA controller + +Optional properties: +- interrupt-names : Name of DMA channel interrupts Supported chips: imx23, imx28. Examples: -dma-apbh@80004000 { + +dma_apbh: dma-apbh@80004000 { compatible = "fsl,imx28-dma-apbh"; - reg = <0x80004000 2000>; + reg = <0x80004000 0x2000>; + interrupts = <82 83 84 85 + 88 88 88 88 + 88 88 88 88 + 87 86 0 0>; + interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3", + "gpmi0", "gmpi1", "gpmi2", "gmpi3", + "gpmi4", "gmpi5", "gpmi6", "gmpi7", + "hsadc", "lcdif", "empty", "empty"; + #dma-cells = <1>; + dma-channels = <16>; }; -dma-apbx@80024000 { +dma_apbx: dma-apbx@80024000 { compatible = "fsl,imx28-dma-apbx"; - reg = <0x80024000 2000>; + reg = <0x80024000 0x2000>; + interrupts = <78 79 66 0 + 80 81 68 69 + 70 71 72 73 + 74 75 76 77>; + interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty", + "saif0", "saif1", "i2c0", "i2c1", + "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx", + "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx"; + #dma-cells = <1>; + dma-channels = <16>; +}; + +DMA clients connected to the MXS DMA controller must use the format +described in the dma.txt file. + +Examples: + +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112>; + dmas = <&dma_apbx 8>, <&dma_apbx 9>; + dma-names = "rx", "tx"; }; diff --git a/Documentation/devicetree/bindings/fb/mxsfb.txt b/Documentation/devicetree/bindings/fb/mxsfb.txt index b41e5e52a676..96ec5179c8a0 100644 --- a/Documentation/devicetree/bindings/fb/mxsfb.txt +++ b/Documentation/devicetree/bindings/fb/mxsfb.txt @@ -5,9 +5,16 @@ Required properties: imx23 and imx28. - reg: Address and length of the register set for lcdif - interrupts: Should contain lcdif interrupts +- display : phandle to display node (see below for details) -Optional properties: -- panel-enable-gpios : Should specify the gpio for panel enable +* display node + +Required properties: +- bits-per-pixel : <16> for RGB565, <32> for RGB888/666. +- bus-width : number of data lines. Could be <8>, <16>, <18> or <24>. + +Required sub-node: +- display-timings : Refer to binding doc display-timing.txt for details. Examples: @@ -15,5 +22,28 @@ lcdif@80030000 { compatible = "fsl,imx28-lcdif"; reg = <0x80030000 2000>; interrupts = <38 86>; - panel-enable-gpios = <&gpio3 30 0>; + + display: display { + bits-per-pixel = <32>; + bus-width = <24>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <33500000>; + hactive = <800>; + vactive = <480>; + hfront-porch = <164>; + hback-porch = <89>; + hsync-len = <10>; + vback-porch = <23>; + vfront-porch = <10>; + vsync-len = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt new file mode 100644 index 000000000000..e466598105fc --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-grgpio.txt @@ -0,0 +1,26 @@ +Aeroflex Gaisler GRGPIO General Purpose I/O cores. + +The GRGPIO GPIO core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the GRGPIO core, a Leon SPARC system, +these properties are built from information in the AMBA plug&play. + +Required properties: + +- name : Should be "GAISLER_GPIO" or "01_01a" + +- reg : Address and length of the register set for the device + +- interrupts : Interrupt numbers for this device + +Optional properties: + +- nbits : The number of gpio lines. If not present driver assumes 32 lines. + +- irqmap : An array with an index for each gpio line. An index is either a valid + index into the interrupts property array, or 0xffffffff that indicates + no irq for that line. Driver provides no interrupt support if not + present. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt new file mode 100644 index 000000000000..629d0ef17308 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt @@ -0,0 +1,47 @@ +Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for +8-/16-bit I/O expander with serial interface (I2C/SPI) + +Required properties: +- compatible : Should be + - "mcp,mcp23s08" for 8 GPIO SPI version + - "mcp,mcp23s17" for 16 GPIO SPI version + - "mcp,mcp23008" for 8 GPIO I2C version or + - "mcp,mcp23017" for 16 GPIO I2C version of the chip +- #gpio-cells : Should be two. + - first cell is the pin number + - second cell is used to specify flags. Flags are currently unused. +- gpio-controller : Marks the device node as a GPIO controller. +- reg : For an address on its bus. I2C uses this a the I2C address of the chip. + SPI uses this to specify the chipselect line which the chip is + connected to. The driver and the SPI variant of the chip support + multiple chips on the same chipselect. Have a look at + mcp,spi-present-mask below. + +Required device specific properties (only for SPI chips): +- mcp,spi-present-mask : This is a present flag, that makes only sense for SPI + chips - as the name suggests. Multiple SPI chips can share the same + SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a + chip connected with the corresponding spi address set. For example if + you have a chip with address 3 connected, you have to set bit3 to 1, + which is 0x08. mcp23s08 chip variant only supports bits 0-3. It is not + possible to mix mcp23s08 and mcp23s17 on the same chipselect. Set at + least one bit to 1 for SPI chips. +- spi-max-frequency = The maximum frequency this chip is able to handle + +Example I2C: +gpiom1: gpio@20 { + compatible = "mcp,mcp23017"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; +}; + +Example SPI: +gpiom1: gpio@0 { + compatible = "mcp,mcp23s17"; + gpio-controller; + #gpio-cells = <2>; + spi-present-mask = <0x01>; + reg = <0>; + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/Documentation/devicetree/bindings/gpio/gpio-omap.txt index bff51a2fee1e..8d950522e7fa 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-omap.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-omap.txt @@ -5,12 +5,12 @@ Required properties: - "ti,omap2-gpio" for OMAP2 controllers - "ti,omap3-gpio" for OMAP3 controllers - "ti,omap4-gpio" for OMAP4 controllers +- gpio-controller : Marks the device node as a GPIO controller. - #gpio-cells : Should be two. - first cell is the pin number - second cell is used to specify optional parameters (unused) -- gpio-controller : Marks the device node as a GPIO controller. +- interrupt-controller: Mark the device node as an interrupt controller. - #interrupt-cells : Should be 2. -- interrupt-controller: Mark the device node as an interrupt controller The first cell is the GPIO number. The second cell is used to specify flags: bits[3:0] trigger type and level flags: @@ -20,8 +20,11 @@ Required properties: 8 = active low level-sensitive. OMAP specific properties: -- ti,hwmods: Name of the hwmod associated to the GPIO: - "gpio<X>", <X> being the 1-based instance number from the HW spec +- ti,hwmods: Name of the hwmod associated to the GPIO: + "gpio<X>", <X> being the 1-based instance number + from the HW spec. +- ti,gpio-always-on: Indicates if a GPIO bank is always powered and + so will never lose its logic state. Example: @@ -29,8 +32,8 @@ Example: gpio4: gpio4 { compatible = "ti,omap4-gpio"; ti,hwmods = "gpio4"; - #gpio-cells = <2>; gpio-controller; - #interrupt-cells = <2>; + #gpio-cells = <2>; interrupt-controller; + #interrupt-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt new file mode 100644 index 000000000000..2b14a940eb75 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt @@ -0,0 +1,20 @@ +* Samsung 2D Graphics Accelerator + +Required properties: + - compatible : value should be one among the following: + (a) "samsung,s5pv210-g2d" for G2D IP present in S5PV210 & Exynos4210 SoC + (b) "samsung,exynos4212-g2d" for G2D IP present in Exynos4x12 SoCs + (c) "samsung,exynos5250-g2d" for G2D IP present in Exynos5250 SoC + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : G2D interrupt number to the CPU. + +Example: + g2d@12800000 { + compatible = "samsung,s5pv210-g2d"; + reg = <0x12800000 0x1000>; + interrupts = <0 89 0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt index 7a3fe9e5f4cb..4e1c8ac01eba 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt @@ -3,10 +3,13 @@ Required properties: - compatible: Should be "fsl,<chip>-i2c" - reg: Should contain registers location and length -- interrupts: Should contain ERROR and DMA interrupts +- interrupts: Should contain ERROR interrupt number - clock-frequency: Desired I2C bus clock frequency in Hz. Only 100000Hz and 400000Hz modes are supported. -- fsl,i2c-dma-channel: APBX DMA channel for the I2C +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and I2C DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". Examples: @@ -15,7 +18,8 @@ i2c0: i2c@80058000 { #size-cells = <0>; compatible = "fsl,imx28-i2c"; reg = <0x80058000 2000>; - interrupts = <111 68>; + interrupts = <111>; clock-frequency = <100000>; - fsl,i2c-dma-channel = <6>; + dmas = <&dma_apbx 6>; + dma-names = "rx-tx"; }; diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt new file mode 100644 index 000000000000..ef77cc7a0e46 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt @@ -0,0 +1,60 @@ +NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver. + +Required properties: +- compatible : should be: + "nvidia,tegra114-i2c" + "nvidia,tegra30-i2c" + "nvidia,tegra20-i2c" + "nvidia,tegra20-i2c-dvc" + Details of compatible are as follows: + nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C + controller. This only support master mode of I2C communication. Register + interface/offset and interrupts handling are different than generic I2C + controller. Driver of DVC I2C controller is only compatible with + "nvidia,tegra20-i2c-dvc". + nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support + master and slave mode of I2C communication. The i2c-tegra driver only + support master mode of I2C communication. Driver of I2C controller is + only compatible with "nvidia,tegra20-i2c". + nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is + very much similar to Tegra20 I2C controller with additional feature: + Continue Transfer Support. This feature helps to implement M_NO_START + as per I2C core API transfer flags. Driver of I2C controller is + compatible with "nvidia,tegra30-i2c" to enable the continue transfer + support. This is also compatible with "nvidia,tegra20-i2c" without + continue transfer support. + nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is + very much similar to Tegra30 I2C controller with some hardware + modification: + - Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and + fast-clk. Tegra114 has only one clock source called as div-clk and + hence clock mechanism is changed in I2C controller. + - Tegra30/Tegra20 I2C controller has enabled per packet transfer by + default and there is no way to disable it. Tegra114 has this + interrupt disable by default and SW need to enable explicitly. + Due to above changes, Tegra114 I2C driver makes incompatible with + previous hardware driver. Hence, tegra114 I2C controller is compatible + with "nvidia,tegra114-i2c". +- reg: Should contain I2C controller registers physical address and length. +- interrupts: Should contain I2C controller interrupts. +- address-cells: Address cells for I2C device address. +- size-cells: Size of the I2C device address. +- clocks: Clock ID as per + Documentation/devicetree/bindings/clock/tegra<chip-id>.txt + for I2C controller. +- clock-names: Name of the clock: + Tegra20/Tegra30 I2C controller: "div-clk and "fast-clk". + Tegra114 I2C controller: "div-clk". + +Example: + + i2c@7000c000 { + compatible = "nvidia,tegra20-i2c"; + reg = <0x7000c000 0x100>; + interrupts = <0 38 0x04>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&tegra_car 12>, <&tegra_car 124>; + clock-names = "div-clk", "fast-clk"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/input/cros-ec-keyb.txt b/Documentation/devicetree/bindings/input/cros-ec-keyb.txt new file mode 100644 index 000000000000..0f6355ce39b5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/cros-ec-keyb.txt @@ -0,0 +1,72 @@ +ChromeOS EC Keyboard + +Google's ChromeOS EC Keyboard is a simple matrix keyboard implemented on +a separate EC (Embedded Controller) device. It provides a message for reading +key scans from the EC. These are then converted into keycodes for processing +by the kernel. + +This binding is based on matrix-keymap.txt and extends/modifies it as follows: + +Required properties: +- compatible: "google,cros-ec-keyb" + +Optional properties: +- google,needs-ghost-filter: True to enable a ghost filter for the matrix +keyboard. This is recommended if the EC does not have its own logic or +hardware for this. + + +Example: + +cros-ec-keyb { + compatible = "google,cros-ec-keyb"; + keypad,num-rows = <8>; + keypad,num-columns = <13>; + google,needs-ghost-filter; + /* + * Keymap entries take the form of 0xRRCCKKKK where + * RR=Row CC=Column KKKK=Key Code + * The values below are for a US keyboard layout and + * are taken from the Linux driver. Note that the + * 102ND key is not used for US keyboards. + */ + linux,keymap = < + /* CAPSLCK F1 B F10 */ + 0x0001003a 0x0002003b 0x00030030 0x00040044 + /* N = R_ALT ESC */ + 0x00060031 0x0008000d 0x000a0064 0x01010001 + /* F4 G F7 H */ + 0x0102003e 0x01030022 0x01040041 0x01060023 + /* ' F9 BKSPACE L_CTRL */ + 0x01080028 0x01090043 0x010b000e 0x0200001d + /* TAB F3 T F6 */ + 0x0201000f 0x0202003d 0x02030014 0x02040040 + /* ] Y 102ND [ */ + 0x0205001b 0x02060015 0x02070056 0x0208001a + /* F8 GRAVE F2 5 */ + 0x02090042 0x03010029 0x0302003c 0x03030006 + /* F5 6 - \ */ + 0x0304003f 0x03060007 0x0308000c 0x030b002b + /* R_CTRL A D F */ + 0x04000061 0x0401001e 0x04020020 0x04030021 + /* S K J ; */ + 0x0404001f 0x04050025 0x04060024 0x04080027 + /* L ENTER Z C */ + 0x04090026 0x040b001c 0x0501002c 0x0502002e + /* V X , M */ + 0x0503002f 0x0504002d 0x05050033 0x05060032 + /* L_SHIFT / . SPACE */ + 0x0507002a 0x05080035 0x05090034 0x050B0039 + /* 1 3 4 2 */ + 0x06010002 0x06020004 0x06030005 0x06040003 + /* 8 7 0 9 */ + 0x06050009 0x06060008 0x0608000b 0x0609000a + /* L_ALT DOWN RIGHT Q */ + 0x060a0038 0x060b006c 0x060c006a 0x07010010 + /* E R W I */ + 0x07020012 0x07030013 0x07040011 0x07050017 + /* U R_SHIFT P O */ + 0x07060016 0x07070036 0x07080019 0x07090018 + /* UP LEFT */ + 0x070b0067 0x070c0069>; +}; diff --git a/Documentation/devicetree/bindings/mfd/as3711.txt b/Documentation/devicetree/bindings/mfd/as3711.txt new file mode 100644 index 000000000000..d98cf18c721c --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/as3711.txt @@ -0,0 +1,73 @@ +AS3711 is an I2C PMIC from Austria MicroSystems with multiple DCDC and LDO power +supplies, a battery charger and an RTC. So far only bindings for the two stepup +DCDC converters are defined. Other DCDC and LDO supplies are configured, using +standard regulator properties, they must belong to a sub-node, called +"regulators" and be called "sd1" to "sd4" and "ldo1" to "ldo8." Stepup converter +configuration should be placed in a subnode, called "backlight." + +Compulsory properties: +- compatible : must be "ams,as3711" +- reg : specifies the I2C address + +To use the SU1 converter as a backlight source the following two properties must +be provided: +- su1-dev : framebuffer phandle +- su1-max-uA : maximum current + +To use the SU2 converter as a backlight source the following two properties must +be provided: +- su2-dev : framebuffer phandle +- su1-max-uA : maximum current + +Additionally one of these properties must be provided to select the type of +feedback used: +- su2-feedback-voltage : voltage feedback is used +- su2-feedback-curr1 : CURR1 input used for current feedback +- su2-feedback-curr2 : CURR2 input used for current feedback +- su2-feedback-curr3 : CURR3 input used for current feedback +- su2-feedback-curr-auto: automatic current feedback selection + +and one of these to select the over-voltage protection pin +- su2-fbprot-lx-sd4 : LX_SD4 is used for over-voltage protection +- su2-fbprot-gpio2 : GPIO2 is used for over-voltage protection +- su2-fbprot-gpio3 : GPIO3 is used for over-voltage protection +- su2-fbprot-gpio4 : GPIO4 is used for over-voltage protection + +If "su2-feedback-curr-auto" is selected, one or more of the following properties +have to be specified: +- su2-auto-curr1 : use CURR1 input for current feedback +- su2-auto-curr2 : use CURR2 input for current feedback +- su2-auto-curr3 : use CURR3 input for current feedback + +Example: + +as3711@40 { + compatible = "ams,as3711"; + reg = <0x40>; + + regulators { + sd4 { + regulator-name = "1.215V"; + regulator-min-microvolt = <1215000>; + regulator-max-microvolt = <1235000>; + }; + ldo2 { + regulator-name = "2.8V CPU"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + }; + + backlight { + compatible = "ams,as3711-bl"; + su2-dev = <&lcdc>; + su2-max-uA = <36000>; + su2-feedback-curr-auto; + su2-fbprot-gpio4; + su2-auto-curr1; + su2-auto-curr2; + su2-auto-curr3; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/cros-ec.txt b/Documentation/devicetree/bindings/mfd/cros-ec.txt new file mode 100644 index 000000000000..e0e59c58a1f9 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -0,0 +1,56 @@ +ChromeOS Embedded Controller + +Google's ChromeOS EC is a Cortex-M device which talks to the AP and +implements various function such as keyboard and battery charging. + +The EC can be connect through various means (I2C, SPI, LPC) and the +compatible string used depends on the inteface. Each connection method has +its own driver which connects to the top level interface-agnostic EC driver. +Other Linux driver (such as cros-ec-keyb for the matrix keyboard) connect to +the top-level driver. + +Required properties (I2C): +- compatible: "google,cros-ec-i2c" +- reg: I2C slave address + +Required properties (SPI): +- compatible: "google,cros-ec-spi" +- reg: SPI chip select + +Required properties (LPC): +- compatible: "google,cros-ec-lpc" +- reg: List of (IO address, size) pairs defining the interface uses + + +Example for I2C: + +i2c@12CA0000 { + cros-ec@1e { + reg = <0x1e>; + compatible = "google,cros-ec-i2c"; + interrupts = <14 0>; + interrupt-parent = <&wakeup_eint>; + wakeup-source; + }; + + +Example for SPI: + +spi@131b0000 { + ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0x0>; + interrupts = <14 0>; + interrupt-parent = <&wakeup_eint>; + wakeup-source; + spi-max-frequency = <5000000>; + controller-data { + cs-gpio = <&gpf0 3 4 3 0>; + samsung,spi-cs; + samsung,spi-feedback-delay = <2>; + }; + }; +}; + + +Example for LPC is not supplied as it is not yet implemented. diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt new file mode 100644 index 000000000000..b381fa696bf9 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt @@ -0,0 +1,80 @@ +OMAP HS USB Host + +Required properties: + +- compatible: should be "ti,usbhs-host" +- reg: should contain one register range i.e. start and length +- ti,hwmods: must contain "usb_host_hs" + +Optional properties: + +- num-ports: number of USB ports. Usually this is automatically detected + from the IP's revision register but can be overridden by specifying + this property. A maximum of 3 ports are supported at the moment. + +- portN-mode: String specifying the port mode for port N, where N can be + from 1 to 3. If the port mode is not specified, that port is treated + as unused. When specified, it must be one of the following. + "ehci-phy", + "ehci-tll", + "ehci-hsic", + "ohci-phy-6pin-datse0", + "ohci-phy-6pin-dpdm", + "ohci-phy-3pin-datse0", + "ohci-phy-4pin-dpdm", + "ohci-tll-6pin-datse0", + "ohci-tll-6pin-dpdm", + "ohci-tll-3pin-datse0", + "ohci-tll-4pin-dpdm", + "ohci-tll-2pin-datse0", + "ohci-tll-2pin-dpdm", + +- single-ulpi-bypass: Must be present if the controller contains a single + ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1 + +Required properties if child node exists: + +- #address-cells: Must be 1 +- #size-cells: Must be 1 +- ranges: must be present + +Properties for children: + +The OMAP HS USB Host subsystem contains EHCI and OHCI controllers. +See Documentation/devicetree/bindings/usb/omap-ehci.txt and +omap3-ohci.txt + +Example for OMAP4: + +usbhshost: usbhshost@4a064000 { + compatible = "ti,usbhs-host"; + reg = <0x4a064000 0x800>; + ti,hwmods = "usb_host_hs"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usbhsohci: ohci@4a064800 { + compatible = "ti,ohci-omap3", "usb-ohci"; + reg = <0x4a064800 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 76 0x4>; + }; + + usbhsehci: ehci@4a064c00 { + compatible = "ti,ehci-omap", "usb-ehci"; + reg = <0x4a064c00 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 77 0x4>; + }; +}; + +&usbhshost { + port1-mode = "ehci-phy"; + port2-mode = "ehci-tll"; + port3-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy 0 &hsusb3_phy>; +}; diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt new file mode 100644 index 000000000000..62fe69724e3b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt @@ -0,0 +1,17 @@ +OMAP HS USB Host TLL (Transceiver-Less Interface) + +Required properties: + +- compatible : should be "ti,usbhs-tll" +- reg : should contain one register range i.e. start and length +- interrupts : should contain the TLL module's interrupt +- ti,hwmod : must contain "usb_tll_hs" + +Example: + + usbhstll: usbhstll@4a062000 { + compatible = "ti,usbhs-tll"; + reg = <0x4a062000 0x1000>; + interrupts = <78>; + ti,hwmods = "usb_tll_hs"; + }; diff --git a/Documentation/devicetree/bindings/mips/ralink.txt b/Documentation/devicetree/bindings/mips/ralink.txt new file mode 100644 index 000000000000..b35a8d04f8b6 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/ralink.txt @@ -0,0 +1,17 @@ +Ralink MIPS SoC device tree bindings + +1. SoCs + +Each device tree must specify a compatible value for the Ralink SoC +it uses in the compatible property of the root node. The compatible +value must be one of the following values: + + ralink,rt2880-soc + ralink,rt3050-soc + ralink,rt3052-soc + ralink,rt3350-soc + ralink,rt3352-soc + ralink,rt3883-soc + ralink,rt5350-soc + ralink,mt7620a-soc + ralink,mt7620n-soc diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt index 54949f6faede..515addc20070 100644 --- a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt @@ -9,15 +9,19 @@ and the properties used by the mxsmmc driver. Required properties: - compatible: Should be "fsl,<chip>-mmc". The supported chips include imx23 and imx28. -- interrupts: Should contain ERROR and DMA interrupts -- fsl,ssp-dma-channel: APBH DMA channel for the SSP +- interrupts: Should contain ERROR interrupt number +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and SSP DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". Examples: ssp0: ssp@80010000 { compatible = "fsl,imx28-mmc"; reg = <0x80010000 2000>; - interrupts = <96 82>; - fsl,ssp-dma-channel = <0>; + interrupts = <96>; + dmas = <&dma_apbh 0>; + dma-names = "rx-tx"; bus-width = <8>; }; diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index e7f8d7ed47eb..6a983c1d87cd 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -56,20 +56,20 @@ Example for an AM33xx board: nand-bus-width = <16>; ti,nand-ecc-opt = "bch8"; - gpmc,sync-clk = <0>; - gpmc,cs-on = <0>; - gpmc,cs-rd-off = <44>; - gpmc,cs-wr-off = <44>; - gpmc,adv-on = <6>; - gpmc,adv-rd-off = <34>; - gpmc,adv-wr-off = <44>; - gpmc,we-off = <40>; - gpmc,oe-off = <54>; - gpmc,access = <64>; - gpmc,rd-cycle = <82>; - gpmc,wr-cycle = <82>; - gpmc,wr-access = <40>; - gpmc,wr-data-mux-bus = <0>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-off-ns = <40>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; #address-cells = <1>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt index 3fb3f9015365..551b2a179d01 100644 --- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -7,10 +7,12 @@ Required properties: - compatible : should be "fsl,<chip>-gpmi-nand" - reg : should contain registers location and length for gpmi and bch. - reg-names: Should contain the reg names "gpmi-nand" and "bch" - - interrupts : The first is the DMA interrupt number for GPMI. - The second is the BCH interrupt number. - - interrupt-names : The interrupt names "gpmi-dma", "bch"; - - fsl,gpmi-dma-channel : Should contain the dma channel it uses. + - interrupts : BCH interrupt number. + - interrupt-names : Should be "bch". + - dmas: DMA specifier, consisting of a phandle to DMA controller node + and GPMI DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. + - dma-names: Must be "rx-tx". Optional properties: - nand-on-flash-bbt: boolean to enable on flash bbt option if not @@ -27,9 +29,10 @@ gpmi-nand@8000c000 { #size-cells = <1>; reg = <0x8000c000 2000>, <0x8000a000 2000>; reg-names = "gpmi-nand", "bch"; - interrupts = <88>, <41>; - interrupt-names = "gpmi-dma", "bch"; - fsl,gpmi-dma-channel = <4>; + interrupts = <41>; + interrupt-names = "bch"; + dmas = <&dma_apbh 4>; + dma-names = "rx-tx"; partition@0 { ... diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index 6e1f61f1e789..9315ac96b49b 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -5,8 +5,12 @@ on platforms which have strong conventions about which portions of a flash are used for what purposes, but which don't use an on-flash partition table such as RedBoot. -#address-cells & #size-cells must both be present in the mtd device and be -equal to 1. +#address-cells & #size-cells must both be present in the mtd device. There are +two valid values for both: +<1>: for partitions that require a single 32-bit cell to represent their + size/address (aka the value is below 4 GiB) +<2>: for partitions that require two 32-bit cells to represent their + size/address (aka the value is 4 GiB or greater). Required properties: - reg : The partition's offset and size within the mtd bank. @@ -36,3 +40,31 @@ flash@0 { reg = <0x0100000 0x200000>; }; }; + +flash@1 { + #address-cells = <1>; + #size-cells = <2>; + + /* a 4 GiB partition */ + partition@0 { + label = "filesystem"; + reg = <0x00000000 0x1 0x00000000>; + }; +}; + +flash@2 { + #address-cells = <2>; + #size-cells = <2>; + + /* an 8 GiB partition */ + partition@0 { + label = "filesystem #1"; + reg = <0x0 0x00000000 0x2 0x00000000>; + }; + + /* a 4 GiB partition */ + partition@200000000 { + label = "filesystem #2"; + reg = <0x2 0x00000000 0x1 0x00000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/gpmc-eth.txt b/Documentation/devicetree/bindings/net/gpmc-eth.txt index 24cb4e46f675..ace4a64b3695 100644 --- a/Documentation/devicetree/bindings/net/gpmc-eth.txt +++ b/Documentation/devicetree/bindings/net/gpmc-eth.txt @@ -26,16 +26,16 @@ Required properties: - bank-width: Address width of the device in bytes. GPMC supports 8-bit and 16-bit devices and so must be either 1 or 2 bytes. - compatible: Compatible string property for the ethernet child device. -- gpmc,cs-on: Chip-select assertion time -- gpmc,cs-rd-off: Chip-select de-assertion time for reads -- gpmc,cs-wr-off: Chip-select de-assertion time for writes -- gpmc,oe-on: Output-enable assertion time -- gpmc,oe-off Output-enable de-assertion time -- gpmc,we-on: Write-enable assertion time -- gpmc,we-off: Write-enable de-assertion time -- gpmc,access: Start cycle to first data capture (read access) -- gpmc,rd-cycle: Total read cycle time -- gpmc,wr-cycle: Total write cycle time +- gpmc,cs-on-ns: Chip-select assertion time +- gpmc,cs-rd-off-ns: Chip-select de-assertion time for reads +- gpmc,cs-wr-off-ns: Chip-select de-assertion time for writes +- gpmc,oe-on-ns: Output-enable assertion time +- gpmc,oe-off-ns: Output-enable de-assertion time +- gpmc,we-on-ns: Write-enable assertion time +- gpmc,we-off-ns: Write-enable de-assertion time +- gpmc,access-ns: Start cycle to first data capture (read access) +- gpmc,rd-cycle-ns: Total read cycle time +- gpmc,wr-cycle-ns: Total write cycle time - reg: Chip-select, base address (relative to chip-select) and size of the memory mapped for the device. Note that base address will be typically 0 as this @@ -65,24 +65,24 @@ gpmc: gpmc@6e000000 { bank-width = <2>; gpmc,mux-add-data; - gpmc,cs-on = <0>; - gpmc,cs-rd-off = <186>; - gpmc,cs-wr-off = <186>; - gpmc,adv-on = <12>; - gpmc,adv-rd-off = <48>; - gpmc,adv-wr-off = <48>; - gpmc,oe-on = <54>; - gpmc,oe-off = <168>; - gpmc,we-on = <54>; - gpmc,we-off = <168>; - gpmc,rd-cycle = <186>; - gpmc,wr-cycle = <186>; - gpmc,access = <114>; - gpmc,page-burst-access = <6>; - gpmc,bus-turnaround = <12>; - gpmc,cycle2cycle-delay = <18>; - gpmc,wr-data-mux-bus = <90>; - gpmc,wr-access = <186>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <186>; + gpmc,cs-wr-off-ns = <186>; + gpmc,adv-on-ns = <12>; + gpmc,adv-rd-off-ns = <48>; + gpmc,adv-wr-off-ns = <48>; + gpmc,oe-on-ns = <54>; + gpmc,oe-off-ns = <168>; + gpmc,we-on-ns = <54>; + gpmc,we-off-ns = <168>; + gpmc,rd-cycle-ns = <186>; + gpmc,wr-cycle-ns = <186>; + gpmc,access-ns = <114>; + gpmc,page-burst-access-ns = <6>; + gpmc,bus-turnaround-ns = <12>; + gpmc,cycle2cycle-delay-ns = <18>; + gpmc,wr-data-mux-bus-ns = <90>; + gpmc,wr-access-ns = <186>; gpmc,cycle2cycle-samecsen; gpmc,cycle2cycle-diffcsen; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 44afa0e5057d..4ff65047bb9a 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -4,7 +4,7 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{macb|gem}" Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs. Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". - Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on + Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on the Cadence GEM, or the generic form: "cdns,gem". - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt index f7e8e8f4d9a3..3077370c89af 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt @@ -70,6 +70,10 @@ Optional subnode-properties: 0: Disable the internal pull-up 1: Enable the internal pull-up +Note that when enabling the pull-up, the internal pad keeper gets disabled. +Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up +will only disable the internal pad keeper. + Examples: pinctrl@80018000 { diff --git a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt new file mode 100644 index 000000000000..ac67c687a327 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt @@ -0,0 +1,43 @@ +* Samsung PWM timers + +Samsung SoCs contain PWM timer blocks which can be used for system clock source +and clock event timers, as well as to drive SoC outputs with PWM signal. Each +PWM timer block provides 5 PWM channels (not all of them can drive physical +outputs - see SoC and board manual). + +Be aware that the clocksource driver supports only uniprocessor systems. + +Required properties: +- compatible : should be one of following: + samsung,s3c2410-pwm - for 16-bit timers present on S3C24xx SoCs + samsung,s3c6400-pwm - for 32-bit timers present on S3C64xx SoCs + samsung,s5p6440-pwm - for 32-bit timers present on S5P64x0 SoCs + samsung,s5pc100-pwm - for 32-bit timers present on S5PC100, S5PV210, + Exynos4210 rev0 SoCs + samsung,exynos4210-pwm - for 32-bit timers present on Exynos4210, + Exynos4x12 and Exynos5250 SoCs +- reg: base address and size of register area +- interrupts: list of timer interrupts (one interrupt per timer, starting at + timer 0) +- #pwm-cells: number of cells used for PWM specifier - must be 3 + the specifier format is as follows: + - phandle to PWM controller node + - index of PWM channel (from 0 to 4) + - PWM signal period in nanoseconds + - bitmask of optional PWM flags: + 0x1 - invert PWM signal + +Optional properties: +- samsung,pwm-outputs: list of PWM channels used as PWM outputs on particular + platform - an array of up to 5 elements being indices of PWM channels + (from 0 to 4), the order does not matter. + +Example: + pwm@7f006000 { + compatible = "samsung,s3c6400-pwm"; + reg = <0x7f006000 0x1000>; + interrupt-parent = <&vic0>; + interrupts = <23>, <24>, <25>, <27>, <28>; + samsung,pwm-outputs = <0>, <1>; + #pwm-cells = <3>; + } diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt index 131e8c11d26f..681afad73778 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt @@ -1,7 +1,9 @@ TI SOC ECAP based APWM controller Required properties: -- compatible: Must be "ti,am33xx-ecap" +- compatible: Must be "ti,<soc>-ecap". + for am33xx - compatible = "ti,am33xx-ecap"; + for da850 - compatible = "ti,da850-ecap", "ti,am33xx-ecap"; - #pwm-cells: Should be 3. Number of cells being used to specify PWM property. First cell specifies the per-chip index of the PWM to use, the second cell is the period in nanoseconds and bit 0 in the third cell is used to @@ -15,9 +17,15 @@ Optional properties: Example: -ecap0: ecap@0 { +ecap0: ecap@0 { /* ECAP on am33xx */ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48300100 0x80>; ti,hwmods = "ecap0"; }; + +ecap0: ecap@0 { /* ECAP on da850 */ + compatible = "ti,da850-ecap", "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x306000 0x80>; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt index 4fc7079d822e..337c6fc65d3f 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt @@ -1,7 +1,9 @@ TI SOC EHRPWM based PWM controller Required properties: -- compatible : Must be "ti,am33xx-ehrpwm" +- compatible: Must be "ti,<soc>-ehrpwm". + for am33xx - compatible = "ti,am33xx-ehrpwm"; + for da850 - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm"; - #pwm-cells: Should be 3. Number of cells being used to specify PWM property. First cell specifies the per-chip index of the PWM to use, the second cell is the period in nanoseconds and bit 0 in the third cell is used to @@ -15,9 +17,15 @@ Optional properties: Example: -ehrpwm0: ehrpwm@0 { +ehrpwm0: ehrpwm@0 { /* EHRPWM on am33xx */ compatible = "ti,am33xx-ehrpwm"; #pwm-cells = <3>; reg = <0x48300200 0x100>; ti,hwmods = "ehrpwm0"; }; + +ehrpwm0: ehrpwm@0 { /* EHRPWM on da850 */ + compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x300000 0x2000>; +}; diff --git a/Documentation/devicetree/bindings/reset/fsl,imx-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx-src.txt new file mode 100644 index 000000000000..13301777e11c --- /dev/null +++ b/Documentation/devicetree/bindings/reset/fsl,imx-src.txt @@ -0,0 +1,49 @@ +Freescale i.MX System Reset Controller +====================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "fsl,<chip>-src" +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain SRC interrupt and CPU WDOG interrupt, + in this order. +- #reset-cells: 1, see below + +example: + +src: src@020d8000 { + compatible = "fsl,imx6q-src"; + reg = <0x020d8000 0x4000>; + interrupts = <0 91 0x04 0 96 0x04>; + #reset-cells = <1>; +}; + +Specifying reset lines connected to IP modules +============================================== + +The system reset controller can be used to reset the GPU, VPU, +IPU, and OpenVG IP modules on i.MX5 and i.MX6 ICs. Those device +nodes should specify the reset line on the SRC in their resets +property, containing a phandle to the SRC device node and a +RESET_INDEX specifying which module to reset, as described in +reset.txt + +example: + + ipu1: ipu@02400000 { + resets = <&src 2>; + }; + ipu2: ipu@02800000 { + resets = <&src 4>; + }; + +The following RESET_INDEX values are valid for i.MX5: +GPU_RESET 0 +VPU_RESET 1 +IPU1_RESET 2 +OPEN_VG_RESET 3 +The following additional RESET_INDEX value is valid for i.MX6: +IPU2_RESET 4 diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt new file mode 100644 index 000000000000..5d2e840ae65c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/pl011.txt @@ -0,0 +1,17 @@ +* ARM AMBA Primecell PL011 serial UART + +Required properties: +- compatible: must be "arm,primecell", "arm,pl011" +- reg: exactly one register range with length 0x1000 +- interrupts: exactly one interrupt specifier + +Optional properties: +- pinctrl: When present, must have one state named "sleep" + and one state named "default" +- clocks: When present, must refer to exactly one clock named + "apb_pclk" +- dmas: When present, may have one or two dma channels. + The first one must be named "rx", the second one + must be named "tx". + +See also bindings/arm/primecell.txt diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt index b77a97c9101e..05ffecb57103 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt @@ -2,6 +2,11 @@ NVIDIA Tegra audio complex Required properties: - compatible : "nvidia,tegra-audio-alc5632" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Must include the following entries: + "pll_a" (The Tegra clock of that name), + "pll_a_out0" (The Tegra clock of that name), + "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,model : The user-visible name of this sound complex. - nvidia,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, @@ -56,4 +61,7 @@ sound { nvidia,i2s-controller = <&tegra_i2s1>; nvidia,audio-codec = <&alc5632>; + + clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>; + clock-names = "pll_a", "pll_a_out0", "mclk"; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt index 04b14cfb1f16..ef1fe7358279 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt @@ -2,6 +2,11 @@ NVIDIA Tegra audio complex for TrimSlice Required properties: - compatible : "nvidia,tegra-audio-trimslice" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Must include the following entries: + "pll_a" (The Tegra clock of that name), + "pll_a_out0" (The Tegra clock of that name), + "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,i2s-controller : The phandle of the Tegra I2S1 controller - nvidia,audio-codec : The phandle of the WM8903 audio codec @@ -11,4 +16,6 @@ sound { compatible = "nvidia,tegra-audio-trimslice"; nvidia,i2s-controller = <&tegra_i2s1>; nvidia,audio-codec = <&codec>; + clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>; + clock-names = "pll_a", "pll_a_out0", "mclk"; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt index c4dd39ce6165..d14510613a7f 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt @@ -2,6 +2,11 @@ NVIDIA Tegra audio complex Required properties: - compatible : "nvidia,tegra-audio-wm8753" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Must include the following entries: + "pll_a" (The Tegra clock of that name), + "pll_a_out0" (The Tegra clock of that name), + "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,model : The user-visible name of this sound complex. - nvidia,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, @@ -50,5 +55,8 @@ sound { nvidia,i2s-controller = <&i2s1>; nvidia,audio-codec = <&wm8753>; + + clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>; + clock-names = "pll_a", "pll_a_out0", "mclk"; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt index d5b0da8bf1d8..3bf722deb722 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt @@ -2,6 +2,11 @@ NVIDIA Tegra audio complex Required properties: - compatible : "nvidia,tegra-audio-wm8903" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Must include the following entries: + "pll_a" (The Tegra clock of that name), + "pll_a_out0" (The Tegra clock of that name), + "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,model : The user-visible name of this sound complex. - nvidia,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, @@ -67,5 +72,8 @@ sound { nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */ nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */ nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */ + + clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>; + clock-names = "pll_a", "pll_a_out0", "mclk"; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt index be35d34e8b26..ad589b163639 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt @@ -2,6 +2,11 @@ NVIDIA Tegra audio complex Required properties: - compatible : "nvidia,tegra-audio-wm9712" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Must include the following entries: + "pll_a" (The Tegra clock of that name), + "pll_a_out0" (The Tegra clock of that name), + "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) - nvidia,model : The user-visible name of this sound complex. - nvidia,audio-routing : A list of the connections between audio components. Each entry is a pair of strings, the first being the connection's sink, @@ -48,4 +53,7 @@ sound { "Mic", "MIC1"; nvidia,ac97-controller = <&ac97>; + + clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>; + clock-names = "pll_a", "pll_a_out0", "mclk"; }; diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt index 7a7eb1e7bda6..f2f3e80934d2 100644 --- a/Documentation/devicetree/bindings/sound/wm8994.txt +++ b/Documentation/devicetree/bindings/sound/wm8994.txt @@ -5,14 +5,70 @@ on the board). Required properties: - - compatible : "wlf,wm1811", "wlf,wm8994", "wlf,wm8958" + - compatible : One of "wlf,wm1811", "wlf,wm8994" or "wlf,wm8958". - reg : the I2C address of the device for I2C, the chip select number for SPI. + - gpio-controller : Indicates this device is a GPIO controller. + - #gpio-cells : Must be 2. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + + - AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, + SPKVDD1-supply, SPKVDD2-supply : power supplies for the device, as covered + in Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + + - interrupts : The interrupt line the IRQ signal for the device is + connected to. This is optional, if it is not connected then none + of the interrupt related properties should be specified. + - interrupt-controller : These devices contain interrupt controllers + and may provide interrupt services to other devices if they have an + interrupt line connected. + - interrupt-parent : The parent interrupt controller. + - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt + + - wlf,gpio-cfg : A list of GPIO configuration register values. If absent, + no configuration of these registers is performed. If any value is + over 0xffff then the register will be left as default. If present 11 + values must be supplied. + + - wlf,micbias-cfg : Two MICBIAS register values for WM1811 or + WM8958. If absent the register defaults will be used. + + - wlf,ldo1ena : GPIO specifier for control of LDO1ENA input to device. + - wlf,ldo2ena : GPIO specifier for control of LDO2ENA input to device. + + - wlf,lineout1-se : If present LINEOUT1 is in single ended mode. + - wlf,lineout2-se : If present LINEOUT2 is in single ended mode. + + - wlf,lineout1-feedback : If present LINEOUT1 has common mode feedback + connected. + - wlf,lineout2-feedback : If present LINEOUT2 has common mode feedback + connected. + + - wlf,ldoena-always-driven : If present LDOENA is always driven. + Example: codec: wm8994@1a { compatible = "wlf,wm8994"; reg = <0x1a>; + + gpio-controller; + #gpio-cells = <2>; + + lineout1-se; + + AVDD2-supply = <®ulator>; + CPVDD-supply = <®ulator>; + DBVDD1-supply = <®ulator>; + DBVDD2-supply = <®ulator>; + DBVDD3-supply = <®ulator>; + SPKVDD1-supply = <®ulator>; + SPKVDD2-supply = <®ulator>; }; diff --git a/Documentation/devicetree/bindings/spi/mxs-spi.txt b/Documentation/devicetree/bindings/spi/mxs-spi.txt index e2e13957c2a4..3499b73293c2 100644 --- a/Documentation/devicetree/bindings/spi/mxs-spi.txt +++ b/Documentation/devicetree/bindings/spi/mxs-spi.txt @@ -3,8 +3,11 @@ Required properties: - compatible: Should be "fsl,<soc>-spi", where soc is "imx23" or "imx28" - reg: Offset and length of the register set for the device -- interrupts: Should contain SSP interrupts (error irq first, dma irq second) -- fsl,ssp-dma-channel: APBX DMA channel for the SSP +- interrupts: Should contain SSP ERROR interrupt +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and SSP DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". Optional properties: - clock-frequency : Input clock frequency to the SPI block in Hz. @@ -17,6 +20,7 @@ ssp0: ssp@80010000 { #size-cells = <0>; compatible = "fsl,imx28-spi"; reg = <0x80010000 0x2000>; - interrupts = <96 82>; - fsl,ssp-dma-channel = <0>; + interrupts = <96>; + dmas = <&dma_apbh 0>; + dma-names = "rx-tx"; }; diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt new file mode 100644 index 000000000000..6d0ac8d0ad9b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -0,0 +1,51 @@ +Davinci SPI controller device bindings + +Required properties: +- #address-cells: number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: should be zero. +- compatible: + - "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family + - "ti,da830-spi" for SPI used similar to that on DA8xx SoC family +- reg: Offset and length of SPI controller register space +- num-cs: Number of chip selects +- ti,davinci-spi-intr-line: interrupt line used to connect the SPI + IP to the interrupt controller within the SoC. Possible values + are 0 and 1. Manual says one of the two possible interrupt + lines can be tied to the interrupt controller. Set this + based on a specifc SoC configuration. +- interrupts: interrupt number mapped to CPU. +- clocks: spi clk phandle + +Example of a NOR flash slave device (n25q032) connected to DaVinci +SPI controller device over the SPI bus. + +spi0:spi@20BF0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,dm6446-spi"; + reg = <0x20BF0000 0x1000>; + num-cs = <4>; + ti,davinci-spi-intr-line = <0>; + interrupts = <338>; + clocks = <&clkspi>; + + flash: n25q032@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p32"; + spi-max-frequency = <25000000>; + reg = <0>; + + partition@0 { + label = "u-boot-spl"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@1 { + label = "test"; + reg = <0x80000 0x380000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt index f158fd31cfda..22ed6797216d 100644 --- a/Documentation/devicetree/bindings/spi/spi_pl022.txt +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -16,6 +16,11 @@ Optional properties: device will be suspended immediately - pl022,rt : indicates the controller should run the message pump with realtime priority to minimise the transfer latency on the bus (boolean) +- dmas : Two or more DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt +- dma-names: Names for the dma channels, if present. There must be at + least one channel named "tx" for transmit and named "rx" for + receive. SPI slave nodes must be children of the SPI master node and can @@ -32,3 +37,34 @@ contain the following properties. - pl022,wait-state : Microwire interface: Wait state - pl022,duplex : Microwire interface: Full/Half duplex + +Example: + + spi@e0100000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0xe0100000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 31 0x4>; + dmas = <&dma-controller 23 1>, + <&dma-controller 24 0>; + dma-names = "rx", "tx"; + + m25p80@1 { + compatible = "st,m25p80"; + reg = <1>; + spi-max-frequency = <12000000>; + spi-cpol; + spi-cpha; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; + }; + diff --git a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt index 8071ac20d4b3..b876d4925a57 100644 --- a/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt +++ b/Documentation/devicetree/bindings/staging/imx-drm/fsl-imx-drm.txt @@ -8,6 +8,8 @@ Required properties: - interrupts: Should contain sync interrupt and error interrupt, in this order. - #crtc-cells: 1, See below +- resets: phandle pointing to the system reset controller and + reset line index, see reset/fsl,imx-src.txt for details example: @@ -16,6 +18,7 @@ ipu: ipu@18000000 { compatible = "fsl,imx53-ipu"; reg = <0x18000000 0x080000000>; interrupts = <11 10>; + resets = <&src 2>; }; Parallel display support diff --git a/Documentation/devicetree/bindings/thermal/armada-thermal.txt b/Documentation/devicetree/bindings/thermal/armada-thermal.txt new file mode 100644 index 000000000000..fff93d5f92de --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/armada-thermal.txt @@ -0,0 +1,22 @@ +* Marvell Armada 370/XP thermal management + +Required properties: + +- compatible: Should be set to one of the following: + marvell,armada370-thermal + marvell,armadaxp-thermal + +- reg: Device's register space. + Two entries are expected, see the examples below. + The first one is required for the sensor register; + the second one is required for the control register + to be used for sensor initialization (a.k.a. calibration). + +Example: + + thermal@d0018300 { + compatible = "marvell,armada370-thermal"; + reg = <0xd0018300 0x4 + 0xd0018304 0x4>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/timer/arm,sp804.txt b/Documentation/devicetree/bindings/timer/arm,sp804.txt new file mode 100644 index 000000000000..5cd8eee74af1 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/arm,sp804.txt @@ -0,0 +1,29 @@ +ARM sp804 Dual Timers +--------------------------------------- + +Required properties: +- compatible: Should be "arm,sp804" & "arm,primecell" +- interrupts: Should contain the list of Dual Timer interrupts. This is the + interrupt for timer 1 and timer 2. In the case of a single entry, it is + the combined interrupt or if "arm,sp804-has-irq" is present that + specifies which timer interrupt is connected. +- reg: Should contain location and length for dual timer register. +- clocks: clocks driving the dual timer hardware. This list should be 1 or 3 + clocks. With 3 clocks, the order is timer0 clock, timer1 clock, + apb_pclk. A single clock can also be specified if the same clock is + used for all clock inputs. + +Optional properties: +- arm,sp804-has-irq = <#>: In the case of only 1 timer irq line connected, this + specifies if the irq connection is for timer 1 or timer 2. A value of 1 + or 2 should be used. + +Example: + + timer0: timer@fc800000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0xfc800000 0x1000>; + interrupts = <0 0 4>, <0 1 4>; + clocks = <&timclk1 &timclk2 &pclk>; + clock-names = "timer1", "timer2", "apb_pclk"; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt index 273a8d5b3300..2c00ec64628e 100644 --- a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt +++ b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt @@ -5,20 +5,18 @@ Required properties: imx23 and imx28. - reg : Address and length of the register set for the device - interrupts : Should contain the auart interrupt numbers - -Optional properties: -- fsl,auart-dma-channel : The DMA channels, the first is for RX, the other - is for TX. If you add this property, it also means that you - will enable the DMA support for the auart. - Note: due to the hardware bug in imx23(see errata : 2836), - only the imx28 can enable the DMA support for the auart. +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and AUART DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: "rx" for RX channel, "tx" for TX channel. Example: auart0: serial@8006a000 { compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006a000 0x2000>; - interrupts = <112 70 71>; - fsl,auart-dma-channel = <8 9>; + interrupts = <112>; + dmas = <&dma_apbx 8>, <&dma_apbx 9>; + dma-names = "rx", "tx"; }; Note: Each auart port should have an alias correctly numbered in "aliases" diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index f66fcddba46f..b3abde736017 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -10,6 +10,8 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. + - clocks: from common clock binding: handle to usb clock. + - clock-names: from common clock binding: Shall be "usbhost". Optional properties: - samsung,vbus-gpio: if present, specifies the GPIO that @@ -22,6 +24,9 @@ Example: reg = <0x12110000 0x100>; interrupts = <0 71 0>; samsung,vbus-gpio = <&gpx2 6 1 3 3>; + + clocks = <&clock 285>; + clock-names = "usbhost"; }; OHCI @@ -31,10 +36,15 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. + - clocks: from common clock binding: handle to usb clock. + - clock-names: from common clock binding: Shall be "usbhost". Example: usb@12120000 { compatible = "samsung,exynos4210-ohci"; reg = <0x12120000 0x100>; interrupts = <0 71 0>; + + clocks = <&clock 285>; + clock-names = "usbhost"; }; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index 662f0f1d2315..d4769f343d6c 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -18,6 +18,7 @@ OMAP MUSB GLUE represents PERIPHERAL. - power : Should be "50". This signifies the controller can supply upto 100mA when operating in host mode. + - usb-phy : the phandle for the PHY device Optional properties: - ctrl-module : phandle of the control module this glue uses to write to diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 4d1919bf2332..6931c4348d24 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -42,6 +42,7 @@ onnn ON Semiconductor Corp. picochip Picochip Ltd powervr PowerVR (deprecated, use img) qcom Qualcomm, Inc. +ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International realtek Realtek Semiconductor Corp. renesas Renesas Electronics Corporation diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt index 589edee37394..589edee37394 100644 --- a/Documentation/devicetree/bindings/drm/exynos/hdmi.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt index fa166d945809..fa166d945809 100644 --- a/Documentation/devicetree/bindings/drm/exynos/hdmiddc.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt diff --git a/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt index 858f4f9b902f..858f4f9b902f 100644 --- a/Documentation/devicetree/bindings/drm/exynos/hdmiphy.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt diff --git a/Documentation/devicetree/bindings/drm/exynos/mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt index 9b2ea0343566..9b2ea0343566 100644 --- a/Documentation/devicetree/bindings/drm/exynos/mixer.txt +++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt diff --git a/Documentation/devicetree/bindings/video/samsung-fimd.txt b/Documentation/devicetree/bindings/video/samsung-fimd.txt new file mode 100644 index 000000000000..778838a0336a --- /dev/null +++ b/Documentation/devicetree/bindings/video/samsung-fimd.txt @@ -0,0 +1,65 @@ +Device-Tree bindings for Samsung SoC display controller (FIMD) + +FIMD (Fully Interactive Mobile Display) is the Display Controller for the +Samsung series of SoCs which transfers the image data from a video memory +buffer to an external LCD interface. + +Required properties: +- compatible: value should be one of the following + "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */ + "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */ + "samsung,s5p6440-fimd"; /* for S5P64X0 SoCs */ + "samsung,s5pc100-fimd"; /* for S5PC100 SoC */ + "samsung,s5pv210-fimd"; /* for S5PV210 SoC */ + "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ + "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */ + +- reg: physical base address and length of the FIMD registers set. + +- interrupt-parent: should be the phandle of the fimd controller's + parent interrupt controller. + +- interrupts: should contain a list of all FIMD IP block interrupts in the + order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier + format depends on the interrupt controller used. + +- interrupt-names: should contain the interrupt names: "fifo", "vsync", + "lcd_sys", in the same order as they were listed in the interrupts + property. + +- pinctrl-0: pin control group to be used for this controller. + +- pinctrl-names: must contain a "default" entry. + +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. + +- clock-names: list of clock names sorted in the same order as the clocks + property. Must contain "sclk_fimd" and "fimd". + +Optional Properties: +- samsung,power-domain: a phandle to FIMD power domain node. + +Example: + +SoC specific DT entry: + + fimd@11c00000 { + compatible = "samsung,exynos4210-fimd"; + interrupt-parent = <&combiner>; + reg = <0x11c00000 0x20000>; + interrupt-names = "fifo", "vsync", "lcd_sys"; + interrupts = <11 0>, <11 1>, <11 2>; + clocks = <&clock 140>, <&clock 283>; + clock-names = "sclk_fimd", "fimd"; + samsung,power-domain = <&pd_lcd0>; + status = "disabled"; + }; + +Board specific DT entry: + + fimd@11c00000 { + pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>; + pinctrl-names = "default"; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/video/simple-framebuffer.txt b/Documentation/devicetree/bindings/video/simple-framebuffer.txt new file mode 100644 index 000000000000..3ea460583111 --- /dev/null +++ b/Documentation/devicetree/bindings/video/simple-framebuffer.txt @@ -0,0 +1,25 @@ +Simple Framebuffer + +A simple frame-buffer describes a raw memory region that may be rendered to, +with the assumption that the display hardware has already been set up to scan +out from that buffer. + +Required properties: +- compatible: "simple-framebuffer" +- reg: Should contain the location and size of the framebuffer memory. +- width: The width of the framebuffer in pixels. +- height: The height of the framebuffer in pixels. +- stride: The number of bytes in each line of the framebuffer. +- format: The format of the framebuffer surface. Valid values are: + - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b). + +Example: + + framebuffer { + compatible = "simple-framebuffer"; + reg = <0x1d385000 (1600 * 1200 * 2)>; + width = <1600>; + height = <1200>; + stride = <(1600 * 2)>; + format = "r5g6b5"; + }; diff --git a/Documentation/devicetree/usage-model.txt b/Documentation/devicetree/usage-model.txt index ef9d06c9f8fd..0efedaad5165 100644 --- a/Documentation/devicetree/usage-model.txt +++ b/Documentation/devicetree/usage-model.txt @@ -191,9 +191,11 @@ Linux it will look something like this: }; The bootargs property contains the kernel arguments, and the initrd-* -properties define the address and size of an initrd blob. The -chosen node may also optionally contain an arbitrary number of -additional properties for platform-specific configuration data. +properties define the address and size of an initrd blob. Note that +initrd-end is the first address after the initrd image, so this doesn't +match the usual semantic of struct resource. The chosen node may also +optionally contain an arbitrary number of additional properties for +platform-specific configuration data. During early boot, the architecture setup code calls of_scan_flat_dt() several times with different helper callbacks to parse device tree |