summaryrefslogtreecommitdiff
path: root/Documentation/devicetree
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree')
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-altera.txt39
-rw-r--r--Documentation/devicetree/bindings/i2c/i2c-stm32.txt29
2 files changed, 65 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-altera.txt b/Documentation/devicetree/bindings/i2c/i2c-altera.txt
new file mode 100644
index 000000000000..767664f448ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-altera.txt
@@ -0,0 +1,39 @@
+* Altera I2C Controller
+* This is Altera's synthesizable logic block I2C Controller for use
+* in Altera's FPGAs.
+
+Required properties :
+ - compatible : should be "altr,softip-i2c-v1.0"
+ - reg : Offset and length of the register set for the device
+ - interrupts : <IRQ> where IRQ is the interrupt number.
+ - clocks : phandle to input clock.
+ - #address-cells = <1>;
+ - #size-cells = <0>;
+
+Recommended properties :
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+
+Optional properties :
+ - fifo-size : Size of the RX and TX FIFOs in bytes.
+ - Child nodes conforming to i2c bus binding
+
+Example :
+
+ i2c@100080000 {
+ compatible = "altr,softip-i2c-v1.0";
+ reg = <0x00000001 0x00080000 0x00000040>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 43 4>;
+ clocks = <&clk_0>;
+ clock-frequency = <100000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ fifo-size = <4>;
+
+ eeprom@51 {
+ compatible = "atmel,24c32";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+ };
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
index 78eaf7b718ed..3b5489966634 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
@@ -1,7 +1,9 @@
* I2C controller embedded in STMicroelectronics STM32 I2C platform
Required properties :
-- compatible : Must be "st,stm32f4-i2c"
+- compatible : Must be one of the following
+ - "st,stm32f4-i2c"
+ - "st,stm32f7-i2c"
- reg : Offset and length of the register set for the device
- interrupts : Must contain the interrupt id for I2C event and then the
interrupt id for I2C error.
@@ -14,8 +16,16 @@ Required properties :
Optional properties :
- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
- the default 100 kHz frequency will be used. As only Normal and Fast modes
- are supported, possible values are 100000 and 400000.
+ the default 100 kHz frequency will be used.
+ For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are
+ 100000 and 400000.
+ For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported,
+ possible values are 100000, 400000 and 1000000.
+- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board
+ (default: 25)
+- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board
+ (default: 10)
+ I2C Timings are derived from these 2 values
Example :
@@ -31,3 +41,16 @@ Example :
pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
pinctrl-names = "default";
};
+
+ i2c@40005400 {
+ compatible = "st,stm32f7-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x40005400 0x400>;
+ interrupts = <31>,
+ <32>;
+ resets = <&rcc STM32F7_APB1_RESET(I2C1)>;
+ clocks = <&rcc 1 CLK_I2C1>;
+ pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
+ pinctrl-names = "default";
+ };