diff options
Diffstat (limited to 'Documentation/devicetree')
12 files changed, 149 insertions, 37 deletions
diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt new file mode 100644 index 000000000000..24a0d06acd1d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt @@ -0,0 +1,43 @@ +Broadcom STB USB PHY + +Required properties: + - compatible: brcm,brcmstb-usb-phy + - reg: two offset and length pairs. + The first pair specifies a manditory set of memory mapped + registers used for general control of the PHY. + The second pair specifies optional registers used by some of + the SoCs that support USB 3.x + - #phy-cells: Shall be 1 as it expects one argument for setting + the type of the PHY. Possible values are: + - PHY_TYPE_USB2 for USB1.1/2.0 PHY + - PHY_TYPE_USB3 for USB3.x PHY + +Optional Properties: +- clocks : clock phandles. +- clock-names: String, clock name. +- brcm,ipp: Boolean, Invert Port Power. + Possible values are: 0 (Don't invert), 1 (Invert) +- brcm,ioc: Boolean, Invert Over Current detection. + Possible values are: 0 (Don't invert), 1 (Invert) +NOTE: one or both of the following two properties must be set +- brcm,has-xhci: Boolean indicating the phy has an XHCI phy. +- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy. +- dr_mode: String, PHY Device mode. + Possible values are: "host", "peripheral ", "drd" or "typec-pd" + If this property is not defined, the phy will default to "host" mode. + +Example: + +usbphy_0: usb-phy@f0470200 { + reg = <0xf0470200 0xb8>, + <0xf0471940 0x6c0>; + compatible = "brcm,brcmstb-usb-phy"; + #phy-cells = <1>; + dr_mode = "host" + brcm,ioc = <1>; + brcm,ipp = <1>; + brcm,has-xhci; + brcm,has-eohci; + clocks = <&usb20>, <&usb30>; + clock-names = "sw_usb", "sw_usb3"; +}; diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index 97977cd29a98..0aced97d8092 100644 --- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -27,7 +27,16 @@ Sub-nodes optional properties: This property is not applicable for "brcm,iproc-ns2-sata-phy", "brcm,iproc-nsp-sata-phy" and "brcm,iproc-sr-sata-phy". -Example: +- brcm,rxaeq-mode: string that indicates the desired RX equalizer + mode, possible values are: + "off" (equivalent to not specifying the property) + "auto" + "manual" (brcm,rxaeq-value is used in that case) + +- brcm,rxaeq-value: when 'rxaeq-mode' is set to "manual", provides the RX + equalizer value that should be used. Allowed range is 0..63. + +Example sata-phy@f0458100 { compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3"; reg = <0xf0458100 0x1e00>, <0xf045804c 0x10>; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt index 91da947ae9b6..eeb9e1874ea6 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt @@ -4,10 +4,13 @@ This file provides information on what the device node for the R-Car generation 2 USB PHY contains. Required properties: -- compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. +- compatible: "renesas,usb-phy-r8a7743" if the device is a part of R8A7743 SoC. + "renesas,usb-phy-r8a7745" if the device is a part of R8A7745 SoC. + "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC. "renesas,usb-phy-r8a7794" if the device is a part of R8A7794 SoC. - "renesas,rcar-gen2-usb-phy" for a generic R-Car Gen2 compatible device. + "renesas,rcar-gen2-usb-phy" for a generic R-Car Gen2 or + RZ/G1 compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index ace9cce2704a..99b651b33110 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -8,6 +8,8 @@ Required properties: SoC. "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796 SoC. + "renesas,usb2-phy-r8a77995" if the device is a part of an + R8A77995 SoC. "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device. When compatible with the generic version, nodes must list the diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index fcf199b64d3d..e64d903bcbe8 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -19,6 +19,8 @@ Required properties: configured in FS mode; - "st,stm32f4x9-hsotg": The DWC2 USB HS controller instance in STM32F4x9 SoCs configured in HS mode; + - "st,stm32f7xx-hsotg": The DWC2 USB HS controller instance in STM32F7xx SoCs + configured in HS mode; - reg : Should contain 1 register range (address and length) - interrupts : Should contain 1 interrupt - clocks: clock provider specifier diff --git a/Documentation/devicetree/bindings/usb/maxim,max3421.txt b/Documentation/devicetree/bindings/usb/maxim,max3421.txt new file mode 100644 index 000000000000..8cdbe0c85188 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/maxim,max3421.txt @@ -0,0 +1,26 @@ +Maxim Integrated SPI-based USB 2.0 host controller MAX3421E + +Required properties: + - compatible: Should be "maxim,max3421" + - spi-max-frequency: maximum frequency for this device must not exceed 26 MHz. + - reg: chip select number to which this device is connected. + - maxim,vbus-en-pin: <GPOUTx ACTIVE_LEVEL> + GPOUTx is the number (1-8) of the GPOUT pin of MAX3421E to drive Vbus. + ACTIVE_LEVEL is 0 or 1. + - interrupts: the interrupt line description for the interrupt controller. + The driver configures MAX3421E for active low level triggered interrupts, + configure your interrupt line accordingly. + +Optional property: + - interrupt-parent: the phandle to the associated interrupt controller. + +Example: + + usb@0 { + compatible = "maxim,max3421"; + reg = <0>; + maxim,vbus-en-pin = <3 1>; + spi-max-frequency = <26000000>; + interrupt-parent = <&PIC>; + interrupts = <42>; + }; diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt index 5611a2e4ddf0..30595964876a 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt @@ -26,10 +26,11 @@ Required properties: - clocks : a list of phandle + clock-specifier pairs, one for each entry in clock-names - clock-names : must contain - "sys_ck": for clock of xHCI MAC - "ref_ck": for reference clock of xHCI MAC - "wakeup_deb_p0": for USB wakeup debounce clock of port0 - "wakeup_deb_p1": for USB wakeup debounce clock of port1 + "sys_ck": controller clock used by normal mode, + the following ones are optional: + "ref_ck": reference clock used by low power mode etc, + "mcu_ck": mcu_bus clock for register access, + "dma_ck": dma_bus clock for data transfer by DMA - phys : a list of phandle + phy specifier pairs @@ -38,6 +39,8 @@ Optional properties: mode; - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup control register, it depends on "mediatek,wakeup-src". + - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, + bit1 for u3port1, ... etc; - vbus-supply : reference to the VBUS regulator; - usb3-lpm-capable : supports USB3.0 LPM - pinctrl-names : a pinctrl state named "default" must be defined @@ -55,9 +58,7 @@ usb30: usb@11270000 { clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, <&pericfg CLK_PERI_USB0>, <&pericfg CLK_PERI_USB1>; - clock-names = "sys_ck", "ref_ck", - "wakeup_deb_p0", - "wakeup_deb_p1"; + clock-names = "sys_ck", "ref_ck"; phys = <&phy_port0 PHY_TYPE_USB3>, <&phy_port1 PHY_TYPE_USB2>; vusb33-supply = <&mt6397_vusb_reg>; @@ -89,9 +90,8 @@ Required properties: - clocks : a list of phandle + clock-specifier pairs, one for each entry in clock-names - - clock-names : must be - "sys_ck": for clock of xHCI MAC - "ref_ck": for reference clock of xHCI MAC + - clock-names : must contain "sys_ck", and the following ones are optional: + "ref_ck", "mcu_ck" and "dma_ck" Optional properties: - vbus-supply : reference to the VBUS regulator; diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt index 49f54767cd21..b2271d8e6b50 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt @@ -14,9 +14,9 @@ Required properties: - vusb33-supply : regulator of USB avdd3.3v - clocks : a list of phandle + clock-specifier pairs, one for each entry in clock-names - - clock-names : must contain "sys_ck" and "ref_ck" for clock of controller; - "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are - depends on "mediatek,enable-wakeup" + - clock-names : must contain "sys_ck" for clock of controller, + the following clocks are optional: + "ref_ck", "mcu_ck" and "dam_ck"; - phys : a list of phandle + phy specifier pairs - dr_mode : should be one of "host", "peripheral" or "otg", refer to usb/generic.txt @@ -30,9 +30,10 @@ Optional properties: when supports dual-role mode. - vbus-supply : reference to the VBUS regulator, needed when supports dual-role mode. - - pinctl-names : a pinctrl state named "default" must be defined, - "id_float" and "id_ground" are optinal which depends on - "mediatek,enable-manual-drd" + - pinctrl-names : a pinctrl state named "default" is optional, and need be + defined if auto drd switch is enabled, that means the property dr_mode + is set as "otg", and meanwhile the property "mediatek,enable-manual-drd" + is not set. - pinctrl-0 : pin control group See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -44,6 +45,8 @@ Optional properties: - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup control register, it depends on "mediatek,enable-wakeup". + - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, + bit1 for u3port1, ... etc; Sub-nodes: The xhci should be added as subnode to mtu3 as shown in the following example @@ -63,9 +66,7 @@ ssusb: usb@11271000 { clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, <&pericfg CLK_PERI_USB0>, <&pericfg CLK_PERI_USB1>; - clock-names = "sys_ck", "ref_ck", - "wakeup_deb_p0", - "wakeup_deb_p1"; + clock-names = "sys_ck", "ref_ck"; vusb33-supply = <&mt6397_vusb_reg>; vbus-supply = <&usb_p0_vbus>; extcon = <&extcon_usb>; diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas_usb3.txt index e28025883b79..87a45e2f9b7f 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usb3.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usb3.txt @@ -15,6 +15,10 @@ Required properties: - interrupts: Interrupt specifier for the USB3.0 Peripheral - clocks: clock phandle and specifier pair +Optional properties: + - phys: phandle + phy specifier pair + - phy-names: must be "usb" + Example of R-Car H3 ES1.x: usb3_peri0: usb@ee020000 { compatible = "renesas,r8a7795-usb3-peri", diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 9e18e000339e..47394ab788e3 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -3,6 +3,8 @@ Renesas Electronics USBHS driver Required properties: - compatible: Must contain one or more of the following: + - "renesas,usbhs-r8a7743" for r8a7743 (RZ/G1M) compatible device + - "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device - "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device - "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device - "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device @@ -10,7 +12,8 @@ Required properties: - "renesas,usbhs-r8a7794" for r8a7794 (R-Car E2) compatible device - "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device - "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device - - "renesas,rcar-gen2-usbhs" for R-Car Gen2 compatible device + - "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device + - "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices - "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device When compatible with the generic version, nodes must list the diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 2d80b60eeabe..ae6e484a8d7c 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -26,6 +26,7 @@ Required properties: Optional properties: - clocks: reference to a clock + - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM - usb3-lpm-capable: determines if platform is USB3 LPM capable - quirk-broken-port-ped: set if the controller has broken port disable mechanism diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt index 3957d4edaa74..168ff819e827 100644 --- a/Documentation/devicetree/bindings/usb/usb251xb.txt +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt @@ -1,16 +1,17 @@ Microchip USB 2.0 Hi-Speed Hub Controller -The device node for the configuration of a Microchip USB251xB/xBi USB 2.0 +The device node for the configuration of a Microchip USB251x/xBi USB 2.0 Hi-Speed Controller. Required properties : - compatible : Should be "microchip,usb251xb" or one of the specific types: "microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b", - "microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi" - - reset-gpios : Should specify the gpio for hub reset + "microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi", + "microchip,usb2517", "microchip,usb2517i" - reg : I2C address on the selected bus (default is <0x2C>) Optional properties : + - reset-gpios : Should specify the gpio for hub reset - skip-config : Skip Hub configuration, but only send the USB-Attach command - vendor-id : Set USB Vendor ID of the hub (16 bit, default is 0x0424) - product-id : Set USB Product ID of the hub (16 bit, default depends on type) @@ -19,29 +20,47 @@ Optional properties : - manufacturer : Set USB Manufacturer string (max 31 characters long) - product : Set USB Product string (max 31 characters long) - serial : Set USB Serial string (max 31 characters long) - - {bus,self}-powered : selects between self- and bus-powered operation (default - is self-powered) - - disable-hi-speed : disable USB Hi-Speed support + - {bus,self}-powered : selects between self- and bus-powered operation + (boolean, default is self-powered) + - disable-hi-speed : disable USB Hi-Speed support (boolean) - {multi,single}-tt : selects between multi- and single-transaction-translator - (default is multi-tt) - - disable-eop : disable End of Packet generation in full-speed mode + (boolean, default is multi-tt) + - disable-eop : disable End of Packet generation in full-speed mode (boolean) - {ganged,individual}-sensing : select over-current sense type in self-powered - mode (default is individual) + mode (boolean, default is individual) - {ganged,individual}-port-switching : select port power switching mode - (default is individual) + (boolean, default is individual) - dynamic-power-switching : enable auto-switching from self- to bus-powered - operation if the local power source is removed or unavailable + operation if the local power source is removed or unavailable (boolean) - oc-delay-us : Delay time (in microseconds) for filtering the over-current sense inputs. Valid values are 100, 4000, 8000 (default) and 16000. If an invalid value is given, the default is used instead. - - compound-device : indicate the hub is part of a compound device - - port-mapping-mode : enable port mapping mode + - compound-device : indicate the hub is part of a compound device (boolean) + - port-mapping-mode : enable port mapping mode (boolean) + - led-{usb,speed}-mode : led usb/speed indication mode selection + (boolean, default is speed mode) - string-support : enable string descriptor support (required for manufacturer, product and serial string configuration) - non-removable-ports : Should specify the ports which have a non-removable device connected. - sp-disabled-ports : Specifies the ports which will be self-power disabled - bp-disabled-ports : Specifies the ports which will be bus-power disabled + - sp-max-total-current-microamp: Specifies max current consumed by the hub + from VBUS when operating in self-powered hub. It includes the hub + silicon along with all associated circuitry including a permanently + attached peripheral (range: 0 - 100000 uA, default 1000 uA) + - bp-max-total-current-microamp: Specifies max current consumed by the hub + from VBUS when operating in self-powered hub. It includes the hub + silicon along with all associated circuitry including a permanently + attached peripheral (range: 0 - 510000 uA, default 100000 uA) + - sp-max-removable-current-microamp: Specifies max current consumed by the hub + from VBUS when operating in self-powered hub. It includes the hub + silicon along with all associated circuitry excluding a permanently + attached peripheral (range: 0 - 100000 uA, default 1000 uA) + - bp-max-removable-current-microamp: Specifies max current consumed by the hub + from VBUS when operating in self-powered hub. It includes the hub + silicon along with all associated circuitry excluding a permanently + attached peripheral (range: 0 - 510000 uA, default 100000 uA) - power-on-time-ms : Specifies the time it takes from the time the host initiates the power-on sequence to a port until the port has adequate power. The value is given in ms in a 0 - 510 range (default is 100ms). @@ -56,7 +75,6 @@ Examples: usb2514b@2c { compatible = "microchip,usb2514b"; reg = <0x2c>; - reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; vendor-id = /bits/ 16 <0x0000>; product-id = /bits/ 16 <0x0000>; string-support; |