diff options
Diffstat (limited to 'Documentation/devicetree')
84 files changed, 1706 insertions, 142 deletions
diff --git a/Documentation/devicetree/bindings/arm/actions.txt b/Documentation/devicetree/bindings/arm/actions.txt new file mode 100644 index 000000000000..3bc7ea575564 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/actions.txt @@ -0,0 +1,39 @@ +Actions Semi platforms device tree bindings +------------------------------------------- + + +S500 SoC +======== + +Required root node properties: + + - compatible : must contain "actions,s500" + + +Modules: + +Root node property compatible must contain, depending on module: + + - LeMaker Guitar: "lemaker,guitar" + + +Boards: + +Root node property compatible must contain, depending on board: + + - LeMaker Guitar Base Board rev. B: "lemaker,guitar-bb-rev-b", "lemaker,guitar" + + +S900 SoC +======== + +Required root node properties: + +- compatible : must contain "actions,s900" + + +Boards: + +Root node property compatible must contain, depending on board: + + - uCRobotics Bubblegum-96: "ucrobotics,bubblegum-96" diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index 799af90dd75b..91cb8e4f2a4f 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -41,6 +41,36 @@ compatible: must be one of: - "atmel,sama5d43" - "atmel,sama5d44" + * "atmel,samv7" for MCUs using a Cortex-M7, shall be extended with the specific + SoC family: + o "atmel,sams70" shall be extended with the specific MCU compatible: + - "atmel,sams70j19" + - "atmel,sams70j20" + - "atmel,sams70j21" + - "atmel,sams70n19" + - "atmel,sams70n20" + - "atmel,sams70n21" + - "atmel,sams70q19" + - "atmel,sams70q20" + - "atmel,sams70q21" + o "atmel,samv70" shall be extended with the specific MCU compatible: + - "atmel,samv70j19" + - "atmel,samv70j20" + - "atmel,samv70n19" + - "atmel,samv70n20" + - "atmel,samv70q19" + - "atmel,samv70q20" + o "atmel,samv71" shall be extended with the specific MCU compatible: + - "atmel,samv71j19" + - "atmel,samv71j20" + - "atmel,samv71j21" + - "atmel,samv71n19" + - "atmel,samv71n20" + - "atmel,samv71n21" + - "atmel,samv71q19" + - "atmel,samv71q20" + - "atmel,samv71q21" + Chipid required properties: - compatible: Should be "atmel,sama5d2-chipid" - reg : Should contain registers location and length diff --git a/Documentation/devicetree/bindings/arm/ccn.txt b/Documentation/devicetree/bindings/arm/ccn.txt index b100d3847d88..29801456c9ee 100644 --- a/Documentation/devicetree/bindings/arm/ccn.txt +++ b/Documentation/devicetree/bindings/arm/ccn.txt @@ -3,6 +3,7 @@ Required properties: - compatible: (standard compatible string) should be one of: + "arm,ccn-502" "arm,ccn-504" "arm,ccn-508" diff --git a/Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt b/Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt new file mode 100644 index 000000000000..298291211ea4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/coresight-cpu-debug.txt @@ -0,0 +1,49 @@ +* CoreSight CPU Debug Component: + +CoreSight CPU debug component are compliant with the ARMv8 architecture +reference manual (ARM DDI 0487A.k) Chapter 'Part H: External debug'. The +external debug module is mainly used for two modes: self-hosted debug and +external debug, and it can be accessed from mmio region from Coresight +and eventually the debug module connects with CPU for debugging. And the +debug module provides sample-based profiling extension, which can be used +to sample CPU program counter, secure state and exception level, etc; +usually every CPU has one dedicated debug module to be connected. + +Required properties: + +- compatible : should be "arm,coresight-cpu-debug"; supplemented with + "arm,primecell" since this driver is using the AMBA bus + interface. + +- reg : physical base address and length of the register set. + +- clocks : the clock associated to this component. + +- clock-names : the name of the clock referenced by the code. Since we are + using the AMBA framework, the name of the clock providing + the interconnect should be "apb_pclk" and the clock is + mandatory. The interface between the debug logic and the + processor core is clocked by the internal CPU clock, so it + is enabled with CPU clock by default. + +- cpu : the CPU phandle the debug module is affined to. When omitted + the module is considered to belong to CPU0. + +Optional properties: + +- power-domains: a phandle to the debug power domain. We use "power-domains" + binding to turn on the debug logic if it has own dedicated + power domain and if necessary to use "cpuidle.off=1" or + "nohlt" in the kernel command line or sysfs node to + constrain idle states to ensure registers in the CPU power + domain are accessible. + +Example: + + debug@f6590000 { + compatible = "arm,coresight-cpu-debug","arm,primecell"; + reg = <0 0xf6590000 0 0x1000>; + clocks = <&sys_ctrl HI6220_DAPB_CLK>; + clock-names = "apb_pclk"; + cpu = <&cpu0>; + }; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 1030f5f50207..ad1913bea8d7 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -193,6 +193,7 @@ nodes to be present and contain the properties described below. "spin-table" # On ARM 32-bit systems this property is optional and can be one of: + "actions,s500-smp" "allwinner,sun6i-a31" "allwinner,sun8i-a23" "arm,realview-smp" @@ -249,7 +250,7 @@ nodes to be present and contain the properties described below. Usage: Optional Value type: <u32> Definition: - # u32 value representing CPU capacity [3] in + # u32 value representing CPU capacity [4] in DMIPS/MHz, relative to highest capacity-dmips-mhz in the system. @@ -476,5 +477,5 @@ cpus { [2] arm/msm/qcom,kpss-acc.txt [3] ARM Linux kernel documentation - idle states bindings Documentation/devicetree/bindings/arm/idle-states.txt -[3] ARM Linux kernel documentation - cpu capacity bindings +[4] ARM Linux kernel documentation - cpu capacity bindings Documentation/devicetree/bindings/arm/cpu-capacity.txt diff --git a/Documentation/devicetree/bindings/arm/gemini.txt b/Documentation/devicetree/bindings/arm/gemini.txt index 0041eb031116..55bf7ce96c44 100644 --- a/Documentation/devicetree/bindings/arm/gemini.txt +++ b/Documentation/devicetree/bindings/arm/gemini.txt @@ -24,6 +24,19 @@ Required nodes: global control registers, with the compatible string "cortina,gemini-syscon", "syscon"; + Required properties on the syscon: + - reg: syscon register location and size. + - #clock-cells: should be set to <1> - the system controller is also a + clock provider. + - #reset-cells: should be set to <1> - the system controller is also a + reset line provider. + + The clock sources have shorthand defines in the include file: + <dt-bindings/clock/cortina,gemini-clock.h> + + The reset lines have shorthand defines in the include file: + <dt-bindings/reset/cortina,gemini-reset.h> + - timer: the soc bus node must have a timer node pointing to the SoC timer block, with the compatible string "cortina,gemini-timer" See: clocksource/cortina,gemini-timer.txt @@ -56,12 +69,15 @@ Example: syscon: syscon@40000000 { compatible = "cortina,gemini-syscon", "syscon"; reg = <0x40000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; }; uart0: serial@42000000 { compatible = "ns16550a"; reg = <0x42000000 0x100>; - clock-frequency = <48000000>; + resets = <&syscon GEMINI_RESET_UART>; + clocks = <&syscon GEMINI_CLK_UART>; interrupts = <18 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; }; @@ -73,12 +89,18 @@ Example: interrupts = <14 IRQ_TYPE_EDGE_FALLING>, /* Timer 1 */ <15 IRQ_TYPE_EDGE_FALLING>, /* Timer 2 */ <16 IRQ_TYPE_EDGE_FALLING>; /* Timer 3 */ + resets = <&syscon GEMINI_RESET_TIMER>; + /* APB clock or RTC clock */ + clocks = <&syscon GEMINI_CLK_APB>, + <&syscon GEMINI_CLK_RTC>; + clock-names = "PCLK", "EXTCLK"; syscon = <&syscon>; }; intcon: interrupt-controller@48000000 { compatible = "cortina,gemini-interrupt-controller"; reg = <0x48000000 0x1000>; + resets = <&syscon GEMINI_RESET_INTCON0>; interrupt-controller; #interrupt-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/arm/keystone/keystone.txt b/Documentation/devicetree/bindings/arm/keystone/keystone.txt index 48f6703a28c8..f310bad04483 100644 --- a/Documentation/devicetree/bindings/arm/keystone/keystone.txt +++ b/Documentation/devicetree/bindings/arm/keystone/keystone.txt @@ -37,3 +37,6 @@ Boards: - K2G EVM compatible = "ti,k2g-evm", "ti,k2g", "ti-keystone" + +- K2G Industrial Communication Engine EVM + compatible = "ti,k2g-ice", "ti,k2g", "ti-keystone" diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 3c23b5de3324..11c0ac4a2d56 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -142,9 +142,9 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "rockchip,px5-evb", "rockchip,px5", "rockchip,rk3368"; -- Rockchip RK1108 Evaluation board +- Rockchip RV1108 Evaluation board Required root node properties: - - compatible = "rockchip,rk1108-evb", "rockchip,rk1108"; + - compatible = "rockchip,rv1108-evb", "rockchip,rv1108"; - Rockchip RK3368 evb: Required root node properties: diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index 170fe0562c63..1a671e329864 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -55,12 +55,19 @@ Boards: compatible = "renesas,bockw", "renesas,r8a7778" - Genmai (RTK772100BC00000BR) compatible = "renesas,genmai", "renesas,r7s72100" + - GR-Peach (X28A-M01-E/F) + compatible = "renesas,gr-peach", "renesas,r7s72100" - Gose (RTP0RC7793SEB00010S) compatible = "renesas,gose", "renesas,r8a7793" - - H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKB00010S) + - H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKBX0010SA00 (H3 ES1.1)) + H3ULCB (R-Car Starter Kit Premier, RTP0RC77951SKBX010SA00 (H3 ES2.0)) compatible = "renesas,h3ulcb", "renesas,r8a7795"; - Henninger compatible = "renesas,henninger", "renesas,r8a7791" + - iWave Systems RZ/G1M Qseven Development Platform (iW-RainboW-G20D-Qseven) + compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7743" + - iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven) + compatible = "iwave,g20m", "renesas,r8a7743" - Koelsch (RTP0RC7791SEB00010S) compatible = "renesas,koelsch", "renesas,r8a7791" - Kyoto Microcomputer Co. KZM-A9-Dual @@ -69,7 +76,7 @@ Boards: compatible = "renesas,kzm9g", "renesas,sh73a0" - Lager (RTP0RC7790SEB00010S) compatible = "renesas,lager", "renesas,r8a7790" - - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKB00010S) + - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKBX0010SA09 (M3 ES1.0)) compatible = "renesas,m3ulcb", "renesas,r8a7796"; - Marzen (R0P7779A00010S) compatible = "renesas,marzen", "renesas,r8a7779" @@ -81,6 +88,8 @@ Boards: compatible = "renesas,salvator-x", "renesas,r8a7795"; - Salvator-X (RTP0RC7796SIPB0011S) compatible = "renesas,salvator-x", "renesas,r8a7796"; + - Salvator-XS (Salvator-X 2nd version, RTP0RC7795SIPB0012S) + compatible = "renesas,salvator-xs", "renesas,r8a7795"; - SILK (RTP0RC7794LCB00011S) compatible = "renesas,silk", "renesas,r8a7794" - SK-RZG1E (YR8A77450S000BE) diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt index b5a4342c1d46..7f1411bbabf7 100644 --- a/Documentation/devicetree/bindings/arm/tegra.txt +++ b/Documentation/devicetree/bindings/arm/tegra.txt @@ -29,7 +29,6 @@ board-specific compatible values: nvidia,harmony nvidia,seaboard nvidia,ventana - nvidia,whistler toradex,apalis_t30 toradex,apalis_t30-eval toradex,apalis-tk1 diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt index 1eceefb20f01..8a6c3c2e58fe 100644 --- a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt +++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt @@ -3,7 +3,8 @@ Broadcom GISB bus Arbiter controller Required properties: - compatible: - "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for 28nm chips + "brcm,bcm7278-gisb-arb" for V7 28nm chips + "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for other 28nm chips "brcm,bcm7435-gisb-arb" for newer 40nm chips "brcm,bcm7400-gisb-arb" for older 40nm chips and all 65nm chips "brcm,bcm7038-gisb-arb" for 130nm chips diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index e9c5a1d9834a..f465647a4dd2 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -22,7 +22,8 @@ Required properties : - #clock-cells : must contain 1 - #reset-cells : must contain 1 -For the PRCM CCUs on H3/A64, one more clock is needed: +For the PRCM CCUs on H3/A64, two more clocks are needed: +- "pll-periph": the SoC's peripheral PLL from the main CCU - "iosc": the SoC's internal frequency oscillator Example for generic CCU: @@ -39,8 +40,8 @@ Example for PRCM CCU: r_ccu: clock@01f01400 { compatible = "allwinner,sun50i-a64-r-ccu"; reg = <0x01f01400 0x100>; - clocks = <&osc24M>, <&osc32k>, <&iosc>; - clock-names = "hosc", "losc", "iosc"; + clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu CLK_PLL_PERIPH0>; + clock-names = "hosc", "losc", "iosc", "pll-periph"; #clock-cells = <1>; #reset-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt index ba0e15ad5bd9..0c38e4b8fc51 100644 --- a/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt +++ b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt @@ -63,64 +63,64 @@ cpu0_opp_table: opp-table { * because they can not be enabled simultaneously on a * single SoC. */ - opp50@300000000 { + opp50-300000000 { opp-hz = /bits/ 64 <300000000>; opp-microvolt = <950000 931000 969000>; opp-supported-hw = <0x06 0x0010>; opp-suspend; }; - opp100@275000000 { + opp100-275000000 { opp-hz = /bits/ 64 <275000000>; opp-microvolt = <1100000 1078000 1122000>; opp-supported-hw = <0x01 0x00FF>; opp-suspend; }; - opp100@300000000 { + opp100-300000000 { opp-hz = /bits/ 64 <300000000>; opp-microvolt = <1100000 1078000 1122000>; opp-supported-hw = <0x06 0x0020>; opp-suspend; }; - opp100@500000000 { + opp100-500000000 { opp-hz = /bits/ 64 <500000000>; opp-microvolt = <1100000 1078000 1122000>; opp-supported-hw = <0x01 0xFFFF>; }; - opp100@600000000 { + opp100-600000000 { opp-hz = /bits/ 64 <600000000>; opp-microvolt = <1100000 1078000 1122000>; opp-supported-hw = <0x06 0x0040>; }; - opp120@600000000 { + opp120-600000000 { opp-hz = /bits/ 64 <600000000>; opp-microvolt = <1200000 1176000 1224000>; opp-supported-hw = <0x01 0xFFFF>; }; - opp120@720000000 { + opp120-720000000 { opp-hz = /bits/ 64 <720000000>; opp-microvolt = <1200000 1176000 1224000>; opp-supported-hw = <0x06 0x0080>; }; - oppturbo@720000000 { + oppturbo-720000000 { opp-hz = /bits/ 64 <720000000>; opp-microvolt = <1260000 1234800 1285200>; opp-supported-hw = <0x01 0xFFFF>; }; - oppturbo@800000000 { + oppturbo-800000000 { opp-hz = /bits/ 64 <800000000>; opp-microvolt = <1260000 1234800 1285200>; opp-supported-hw = <0x06 0x0100>; }; - oppnitro@1000000000 { + oppnitro-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <1325000 1298500 1351500>; opp-supported-hw = <0x04 0x0200>; diff --git a/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt new file mode 100644 index 000000000000..a767259dedad --- /dev/null +++ b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt @@ -0,0 +1,24 @@ +Device-tree bindings for gpio-based FSI master driver +----------------------------------------------------- + +Required properties: + - compatible = "fsi-master-gpio"; + - clock-gpios = <gpio-descriptor>; : GPIO for FSI clock + - data-gpios = <gpio-descriptor>; : GPIO for FSI data signal + +Optional properties: + - enable-gpios = <gpio-descriptor>; : GPIO for enable signal + - trans-gpios = <gpio-descriptor>; : GPIO for voltage translator enable + - mux-gpios = <gpio-descriptor>; : GPIO for pin multiplexing with other + functions (eg, external FSI masters) + +Examples: + + fsi-master { + compatible = "fsi-master-gpio", "fsi-master"; + clock-gpios = <&gpio 0>; + data-gpios = <&gpio 1>; + enable-gpios = <&gpio 2>; + trans-gpios = <&gpio 3>; + mux-gpios = <&gpio 4>; + } diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt index 42c3bb2d53e8..01e331a5f3e7 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt @@ -41,9 +41,9 @@ Required properties: Optional properties: In order to use the GPIO lines in PWM mode, some additional optional -properties are required. Only Armada 370 and XP support these properties. +properties are required. -- compatible: Must contain "marvell,armada-370-xp-gpio" +- compatible: Must contain "marvell,armada-370-gpio" - reg: an additional register set is needed, for the GPIO Blink Counter on/off registers. @@ -71,7 +71,7 @@ Example: }; gpio1: gpio@18140 { - compatible = "marvell,armada-370-xp-gpio"; + compatible = "marvell,armada-370-gpio"; reg = <0x18140 0x40>, <0x181c8 0x08>; reg-names = "gpio", "pwm"; ngpios = <17>; diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt index 85f8c0d084fa..29416f9c3220 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -5,9 +5,13 @@ Required properties: - reg: Should contain GPIO controller registers location and length - interrupts: Should be the port interrupt shared by all the pins. - #gpio-cells: Should be two. The first cell is the pin number and - the second cell is used to specify optional parameters (currently - unused). + the second cell is used to specify optional parameters to declare if the GPIO + is active high or low. See gpio.txt. - gpio-controller: Marks the device node as a GPIO controller. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. The first cell is the pin number and the + second cell is used to specify irq type flags, see the two cell description + in interrupt-controller/interrupts.txt for details. optional properties: - #gpio-lines: Number of gpio if absent 32. @@ -21,5 +25,7 @@ Example: #gpio-cells = <2>; gpio-controller; #gpio-lines = <19>; + interrupt-controller; + #interrupt-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt new file mode 100644 index 000000000000..d3b6e1a4713a --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt @@ -0,0 +1,86 @@ +ARM Mali Midgard GPU +==================== + +Required properties: + +- compatible : + * Must contain one of the following: + + "arm,mali-t604" + + "arm,mali-t624" + + "arm,mali-t628" + + "arm,mali-t720" + + "arm,mali-t760" + + "arm,mali-t820" + + "arm,mali-t830" + + "arm,mali-t860" + + "arm,mali-t880" + * which must be preceded by one of the following vendor specifics: + + "amlogic,meson-gxm-mali" + + "rockchip,rk3288-mali" + +- reg : Physical base address of the device and length of the register area. + +- interrupts : Contains the three IRQ lines required by Mali Midgard devices. + +- interrupt-names : Contains the names of IRQ resources in the order they were + provided in the interrupts property. Must contain: "job", "mmu", "gpu". + + +Optional properties: + +- clocks : Phandle to clock for the Mali Midgard device. + +- mali-supply : Phandle to regulator for the Mali device. Refer to + Documentation/devicetree/bindings/regulator/regulator.txt for details. + +- operating-points-v2 : Refer to Documentation/devicetree/bindings/power/opp.txt + for details. + + +Example for a Mali-T760: + +gpu@ffa30000 { + compatible = "rockchip,rk3288-mali", "arm,mali-t760", "arm,mali-midgard"; + reg = <0xffa30000 0x10000>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "job", "mmu", "gpu"; + clocks = <&cru ACLK_GPU>; + mali-supply = <&vdd_gpu>; + operating-points-v2 = <&gpu_opp_table>; + power-domains = <&power RK3288_PD_GPU>; +}; + +gpu_opp_table: opp_table0 { + compatible = "operating-points-v2"; + + opp@533000000 { + opp-hz = /bits/ 64 <533000000>; + opp-microvolt = <1250000>; + }; + opp@450000000 { + opp-hz = /bits/ 64 <450000000>; + opp-microvolt = <1150000>; + }; + opp@400000000 { + opp-hz = /bits/ 64 <400000000>; + opp-microvolt = <1125000>; + }; + opp@350000000 { + opp-hz = /bits/ 64 <350000000>; + opp-microvolt = <1075000>; + }; + opp@266000000 { + opp-hz = /bits/ 64 <266000000>; + opp-microvolt = <1025000>; + }; + opp@160000000 { + opp-hz = /bits/ 64 <160000000>; + opp-microvolt = <925000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <912500>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt new file mode 100644 index 000000000000..2907dab56298 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt @@ -0,0 +1,99 @@ +General Purpose I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses a mux controller +from the mux subsystem to route the I2C signals. + + .-----. .-----. + | dev | | dev | + .------------. '-----' '-----' + | SoC | | | + | | .--------+--------' + | .------. | .------+ child bus A, on MUX value set to 0 + | | I2C |-|--| Mux | + | '------' | '--+---+ child bus B, on MUX value set to 1 + | .------. | | '----------+--------+--------. + | | MUX- | | | | | | + | | Ctrl |-|-----+ .-----. .-----. .-----. + | '------' | | dev | | dev | | dev | + '------------' '-----' '-----' '-----' + +Required properties: +- compatible: i2c-mux +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. +- mux-controls: The phandle of the mux controller to use for operating the + mux. +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. The sub-bus number + is also the mux-controller state described in ../mux/mux-controller.txt + +Optional properties: +- mux-locked: If present, explicitly allow unrelated I2C transactions on the + parent I2C adapter at these times: + + during setup of the multiplexer + + between setup of the multiplexer and the child bus I2C transaction + + between the child bus I2C transaction and releasing of the multiplexer + + during releasing of the multiplexer + However, I2C transactions to devices behind all I2C multiplexers connected + to the same parent adapter that this multiplexer is connected to are blocked + for the full duration of the complete multiplexed I2C transaction (i.e. + including the times covered by the above list). + If mux-locked is not present, the multiplexer is assumed to be parent-locked. + This means that no unrelated I2C transactions are allowed on the parent I2C + adapter for the complete multiplexed I2C transaction. + The properties of mux-locked and parent-locked multiplexers are discussed + in more detail in Documentation/i2c/i2c-topology. + +For each i2c child node, an I2C child bus will be created. They will +be numbered based on their order in the device tree. + +Whenever an access is made to a device on a child bus, the value set +in the relevant node's reg property will be set as the state in the +mux controller. + +Example: + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>, + <&pioA 1 GPIO_ACTIVE_HIGH>; + }; + + i2c-mux { + compatible = "i2c-mux"; + mux-locked; + i2c-parent = <&i2c1>; + + mux-controls = <&mux>; + + #address-cells = <1>; + #size-cells = <0>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7 1>; + reset-active-low; + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt index 047189192aec..f413e82c8b83 100644 --- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -2,6 +2,8 @@ Required properties: - compatible: depending on the SoC this should be one of: + - "amlogic,meson8-saradc" for Meson8 + - "amlogic,meson8b-saradc" for Meson8b - "amlogic,meson-gxbb-saradc" for GXBB - "amlogic,meson-gxl-saradc" for GXL - "amlogic,meson-gxm-saradc" for GXM diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt index f5b0adae6010..df5b9f2ad8d8 100644 --- a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt +++ b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt @@ -1,4 +1,4 @@ -* Renesas RCar GyroADC device driver +* Renesas R-Car GyroADC device driver The GyroADC block is a reduced SPI block with up to 8 chipselect lines, which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs @@ -16,8 +16,7 @@ Required properties: - clocks: References to all the clocks specified in the clock-names property as specified in Documentation/devicetree/bindings/clock/clock-bindings.txt. -- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block - clock, the "if" is the interface clock. +- clock-names: Shall contain "fck". The "fck" is the GyroADC block clock. - power-domains: Must contain a reference to the PM domain, if available. - #address-cells: Should be <1> (setting for the subnodes) for all ADCs except for "fujitsu,mb88101a". Should be <0> (setting for @@ -75,8 +74,8 @@ Example: adc@e6e54000 { compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; reg = <0 0xe6e54000 0 64>; - clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>; - clock-names = "fck", "if"; + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>; + clock-names = "fck"; power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; pinctrl-0 = <&adc_pins>; diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt index e35f9f1b3200..8310073f14e1 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -21,11 +21,19 @@ own configurable sequence and trigger: Contents of a stm32 adc root node: ----------------------------------- Required properties: -- compatible: Should be "st,stm32f4-adc-core". +- compatible: Should be one of: + "st,stm32f4-adc-core" + "st,stm32h7-adc-core" - reg: Offset and length of the ADC block register set. - interrupts: Must contain the interrupt for ADC block. -- clocks: Clock for the analog circuitry (common to all ADCs). -- clock-names: Must be "adc". +- clocks: Core can use up to two clocks, depending on part used: + - "adc" clock: for the analog circuitry, common to all ADCs. + It's required on stm32f4. + It's optional on stm32h7. + - "bus" clock: for registers access, common to all ADCs. + It's not present on stm32f4. + It's required on stm32h7. +- clock-names: Must be "adc" and/or "bus" depending on part used. - interrupt-controller: Identifies the controller node as interrupt-parent - vref-supply: Phandle to the vref input analog reference voltage. - #interrupt-cells = <1>; @@ -42,14 +50,18 @@ An ADC block node should contain at least one subnode, representing an ADC instance available on the machine. Required properties: -- compatible: Should be "st,stm32f4-adc". +- compatible: Should be one of: + "st,stm32f4-adc" + "st,stm32h7-adc" - reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200). -- clocks: Input clock private to this ADC instance. +- clocks: Input clock private to this ADC instance. It's required only on + stm32f4, that has per instance clock input for registers access. - interrupt-parent: Phandle to the parent interrupt controller. - interrupts: IRQ Line for the ADC (e.g. may be 0 for adc@0, 1 for adc@100 or 2 for adc@200). - st,adc-channels: List of single-ended channels muxed for this ADC. - It can have up to 16 channels, numbered from 0 to 15 (resp. for in0..in15). + It can have up to 16 channels on stm32f4 or 20 channels on stm32h7, numbered + from 0 to 15 or 19 (resp. for in0..in15 or in0..in19). - #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in Documentation/devicetree/bindings/iio/iio-bindings.txt @@ -58,7 +70,9 @@ Optional properties: See ../../dma/dma.txt for details. - dma-names: Must be "rx" when dmas property is being used. - assigned-resolution-bits: Resolution (bits) to use for conversions. Must - match device available resolutions (e.g. can be 6, 8, 10 or 12 on stm32f4). + match device available resolutions: + * can be 6, 8, 10 or 12 on stm32f4 + * can be 8, 10, 12, 14 or 16 on stm32h7 Default is maximum resolution if unset. Example: diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc084s021.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc084s021.txt new file mode 100644 index 000000000000..4259e50620bc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc084s021.txt @@ -0,0 +1,19 @@ +* Texas Instruments' ADC084S021 + +Required properties: + - compatible : Must be "ti,adc084s021" + - reg : SPI chip select number for the device + - vref-supply : The regulator supply for ADC reference voltage + - spi-cpol : Per spi-bus bindings + - spi-cpha : Per spi-bus bindings + - spi-max-frequency : Per spi-bus bindings + +Example: +adc@0 { + compatible = "ti,adc084s021"; + reg = <0>; + vref-supply = <&adc_vref>; + spi-cpol; + spi-cpha; + spi-max-frequency = <16000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc108s102.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc108s102.txt new file mode 100644 index 000000000000..bbbbb4a9f58f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc108s102.txt @@ -0,0 +1,18 @@ +* Texas Instruments' ADC108S102 and ADC128S102 ADC chip + +Required properties: + - compatible: Should be "ti,adc108s102" + - reg: spi chip select number for the device + - vref-supply: The regulator supply for ADC reference voltage + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,adc108s102"; + reg = <0>; + vref-supply = <&vdd_supply>; + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt index 8305fb05ffda..6f28ff55f3ec 100644 --- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt +++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt @@ -13,7 +13,8 @@ Optional properties: "data ready" (valid values: 1 or 2). - interrupt-parent: should be the phandle for the interrupt controller - interrupts: interrupt mapping for IRQ. It should be configured with - flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING. + flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or + IRQ_TYPE_EDGE_FALLING. Refer to interrupt-controller/interrupts.txt for generic interrupt client node bindings. diff --git a/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt b/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt new file mode 100644 index 000000000000..c82794002595 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt @@ -0,0 +1,39 @@ +I/O channel multiplexer bindings + +If a multiplexer is used to select which hardware signal is fed to +e.g. an ADC channel, these bindings describe that situation. + +Required properties: +- compatible : "io-channel-mux" +- io-channels : Channel node of the parent channel that has multiplexed + input. +- io-channel-names : Should be "parent". +- #address-cells = <1>; +- #size-cells = <0>; +- mux-controls : Mux controller node to use for operating the mux +- channels : List of strings, labeling the mux controller states. + +For each non-empty string in the channels property, an io-channel will +be created. The number of this io-channel is the same as the index into +the list of strings in the channels property, and also matches the mux +controller state. The mux controller state is described in +../mux/mux-controller.txt + +Example: + mux: mux-controller { + compatible = "mux-gpio"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>, + <&pioA 1 GPIO_ACTIVE_HIGH>; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux>; + + channels = "sync", "in", "system-regulator"; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-nmi.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-nmi.txt index 81cd3692405e..4ae553eb333d 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-nmi.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sunxi-nmi.txt @@ -3,8 +3,11 @@ Allwinner Sunxi NMI Controller Required properties: -- compatible : should be "allwinner,sun7i-a20-sc-nmi" or - "allwinner,sun6i-a31-sc-nmi" or "allwinner,sun9i-a80-nmi" +- compatible : should be one of the following: + - "allwinner,sun7i-a20-sc-nmi" + - "allwinner,sun6i-a31-sc-nmi" (deprecated) + - "allwinner,sun6i-a31-r-intc" + - "allwinner,sun9i-a80-nmi" - reg : Specifies base physical address and size of the registers. - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an diff --git a/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-i2c-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-i2c-ic.txt new file mode 100644 index 000000000000..033cc82e5684 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-i2c-ic.txt @@ -0,0 +1,25 @@ +Device tree configuration for the I2C Interrupt Controller on the AST24XX and +AST25XX SoCs. + +Required Properties: +- #address-cells : should be 1 +- #size-cells : should be 1 +- #interrupt-cells : should be 1 +- compatible : should be "aspeed,ast2400-i2c-ic" + or "aspeed,ast2500-i2c-ic" +- reg : address start and range of controller +- interrupts : interrupt number +- interrupt-controller : denotes that the controller receives and fires + new interrupts for child busses + +Example: + +i2c_ic: interrupt-controller@0 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <1>; + compatible = "aspeed,ast2400-i2c-ic"; + reg = <0x0 0x40>; + interrupts = <12>; + interrupt-controller; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt index 6c6e85324b9d..e3fea0758d25 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt @@ -1,12 +1,13 @@ Aspeed Vectored Interrupt Controller -These bindings are for the Aspeed AST2400 interrupt controller register layout. -The SoC has an legacy register layout, but this driver does not support that -mode of operation. +These bindings are for the Aspeed interrupt controller. The AST2400 and +AST2500 SoC families include a legacy register layout before a re-designed +layout, but the bindings do not prescribe the use of one or the other. Required properties: -- compatible : should be "aspeed,ast2400-vic". +- compatible : "aspeed,ast2400-vic" + "aspeed,ast2500-vic" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,gicp.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,gicp.txt new file mode 100644 index 000000000000..64a00ceb7da4 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,gicp.txt @@ -0,0 +1,27 @@ +Marvell GICP Controller +----------------------- + +GICP is a Marvell extension of the GIC that allows to trigger GIC SPI +interrupts by doing a memory transaction. It is used by the ICU +located in the Marvell CP110 to turn wired interrupts inside the CP +into GIC SPI interrupts. + +Required properties: + +- compatible: Must be "marvell,ap806-gicp" + +- reg: Must be the address and size of the GICP SPI registers + +- marvell,spi-ranges: tuples of GIC SPI interrupts ranges available + for this GICP + +- msi-controller: indicates that this is an MSI controller + +Example: + +gicp_spi: gicp-spi@3f0040 { + compatible = "marvell,ap806-gicp"; + reg = <0x3f0040 0x10>; + marvell,spi-ranges = <64 64>, <288 64>; + msi-controller; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt new file mode 100644 index 000000000000..aa8bf2ec8905 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,icu.txt @@ -0,0 +1,51 @@ +Marvell ICU Interrupt Controller +-------------------------------- + +The Marvell ICU (Interrupt Consolidation Unit) controller is +responsible for collecting all wired-interrupt sources in the CP and +communicating them to the GIC in the AP, the unit translates interrupt +requests on input wires to MSG memory mapped transactions to the GIC. + +Required properties: + +- compatible: Should be "marvell,cp110-icu" + +- reg: Should contain ICU registers location and length. + +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value shall be 3. + + The 1st cell is the group type of the ICU interrupt. Possible group + types are: + + ICU_GRP_NSR (0x0) : Shared peripheral interrupt, non-secure + ICU_GRP_SR (0x1) : Shared peripheral interrupt, secure + ICU_GRP_SEI (0x4) : System error interrupt + ICU_GRP_REI (0x5) : RAM error interrupt + + The 2nd cell is the index of the interrupt in the ICU unit. + + The 3rd cell is the type of the interrupt. See arm,gic.txt for + details. + +- interrupt-controller: Identifies the node as an interrupt + controller. + +- msi-parent: Should point to the GICP controller, the GIC extension + that allows to trigger interrupts using MSG memory mapped + transactions. + +Example: + +icu: interrupt-controller@1e0000 { + compatible = "marvell,cp110-icu"; + reg = <0x1e0000 0x10>; + #interrupt-cells = <3>; + interrupt-controller; + msi-parent = <&gicp>; +}; + +usb3h0: usb3@500000 { + interrupt-parent = <&icu>; + interrupts = <ICU_GRP_NSR 106 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index 24b656014089..1d4afe9644b6 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -1,4 +1,4 @@ -Common leds properties. +* Common leds properties. LED and flash LED devices provide the same basic functionality as current regulators, but extended with LED and flash LED specific features like @@ -49,6 +49,22 @@ Optional properties for child nodes: - panic-indicator : This property specifies that the LED should be used, if at all possible, as a panic indicator. +- trigger-sources : List of devices which should be used as a source triggering + this LED activity. Some LEDs can be related to a specific + device and should somehow indicate its state. E.g. USB 2.0 + LED may react to device(s) in a USB 2.0 port(s). + Another common example is switch or router with multiple + Ethernet ports each of them having its own LED assigned + (assuming they are not hardwired). In such cases this + property should contain phandle(s) of related source + device(s). + In many cases LED can be related to more than one device + (e.g. one USB LED vs. multiple USB ports). Each source + should be represented by a node in the device tree and be + referenced by a phandle and a set of phandle arguments. A + length of arguments should be specified by the + #trigger-source-cells property in the source node. + Required properties for flash LED child nodes: - flash-max-microamp : Maximum flash LED supply current in microamperes. - flash-max-timeout-us : Maximum timeout in microseconds after which the flash @@ -59,7 +75,17 @@ property can be omitted. For controllers that have no configurable timeout the flash-max-timeout-us property can be omitted. -Examples: +* Trigger source providers + +Each trigger source should be represented by a device tree node. It may be e.g. +a USB port or an Ethernet device. + +Required properties for trigger source: +- #trigger-source-cells : Number of cells in a source trigger. Typically 0 for + nodes of simple trigger sources (e.g. a specific USB + port). + +* Examples gpio-leds { compatible = "gpio-leds"; @@ -69,6 +95,11 @@ gpio-leds { linux,default-trigger = "heartbeat"; gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; }; + + usb { + gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + trigger-sources = <&ohci_port1>, <&ehci_port1>; + }; }; max77693-led { diff --git a/Documentation/devicetree/bindings/mfd/stm32-timers.txt b/Documentation/devicetree/bindings/mfd/stm32-timers.txt index bbd083f5600a..1db6e0057a63 100644 --- a/Documentation/devicetree/bindings/mfd/stm32-timers.txt +++ b/Documentation/devicetree/bindings/mfd/stm32-timers.txt @@ -31,7 +31,7 @@ Example: compatible = "st,stm32-timers"; reg = <0x40010000 0x400>; clocks = <&rcc 0 160>; - clock-names = "clk_int"; + clock-names = "int"; pwm { compatible = "st,stm32-pwm"; diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index 38833e63a59f..8af1202b381d 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -61,6 +61,10 @@ Optional properties: There should be 9 entries here, one for each gpio. - ti,system-power-controller: Telling whether or not this pmic is controlling the system power. +- ti,sleep-enable: Enable SLEEP state. +- ti,sleep-keep-therm: Keep thermal monitoring on in sleep state. +- ti,sleep-keep-ck32k: Keep the 32KHz clock output on in sleep state. +- ti,sleep-keep-hsclk: Keep high speed internal clock on in sleep state. Regulator Optional properties: - ti,regulator-ext-sleep-control: enable external sleep diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index 520d61dad6dd..49ed3ad2524a 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -15,6 +15,7 @@ Required Properties: - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 - "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RV1108 - "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3036 + - "rockchip,rk3328-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3328 - "rockchip,rk3368-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3368 - "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc": for Rockchip RK3399 @@ -31,6 +32,10 @@ Optional Properties: probing, low speeds or in case where all phases work at tuning time. If not specified 0 deg will be used. +* rockchip,desired-num-phases: The desired number of times that the host + execute tuning when needed. If not specified, the host will do tuning + for 360 times, namely tuning for each degree. + Example: rkdwmmc0@12200000 { diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index 74166a0d460d..0e026c151c1c 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -18,7 +18,7 @@ Required properties: Optional properties: ti,dual-volt: boolean, supports dual voltage cards <supply-name>-supply: phandle to the regulator device tree node -"supply-name" examples are "vmmc", "vmmc_aux" etc +"supply-name" examples are "vmmc", "vmmc_aux"(deprecated)/"vqmmc" etc ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index f6bee57e453a..9bb66e476672 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -59,8 +59,22 @@ Required properties: - reg: should contain 2 register ranges. The first one is pointing to the PMECC block, and the second one to the PMECC_ERRLOC block. +* SAMA5 NFC I/O bindings: + +SAMA5 SoCs embed an advanced NAND controller logic to automate READ/WRITE page +operations. This interface to this logic is placed in a separate I/O range and +should thus have its own DT node. + +- compatible: should be "atmel,sama5d3-nfc-io", "syscon". +- reg: should contain the I/O range used to interact with the NFC logic. + Example: + nfc_io: nfc-io@70000000 { + compatible = "atmel,sama5d3-nfc-io", "syscon"; + reg = <0x70000000 0x8000000>; + }; + pmecc: ecc-engine@ffffc070 { compatible = "atmel,at91sam9g45-pmecc"; reg = <0xffffc070 0x490>, diff --git a/Documentation/devicetree/bindings/mux/adi,adg792a.txt b/Documentation/devicetree/bindings/mux/adi,adg792a.txt new file mode 100644 index 000000000000..96b787a69f50 --- /dev/null +++ b/Documentation/devicetree/bindings/mux/adi,adg792a.txt @@ -0,0 +1,75 @@ +Bindings for Analog Devices ADG792A/G Triple 4:1 Multiplexers + +Required properties: +- compatible : "adi,adg792a" or "adi,adg792g" +- #mux-control-cells : <0> if parallel (the three muxes are bound together + with a single mux controller controlling all three muxes), or <1> if + not (one mux controller for each mux). +* Standard mux-controller bindings as described in mux-controller.txt + +Optional properties for ADG792G: +- gpio-controller : if present, #gpio-cells below is required. +- #gpio-cells : should be <2> + - First cell is the GPO line number, i.e. 0 or 1 + - Second cell is used to specify active high (0) + or active low (1) + +Optional properties: +- idle-state : if present, array of states that the mux controllers will have + when idle. The special state MUX_IDLE_AS_IS is the default and + MUX_IDLE_DISCONNECT is also supported. + +States 0 through 3 correspond to signals A through D in the datasheet. + +Example: + + /* + * Three independent mux controllers (of which one is used). + * Mux 0 is disconnected when idle, mux 1 idles in the previously + * selected state and mux 2 idles with signal B. + */ + &i2c0 { + mux: mux-controller@50 { + compatible = "adi,adg792a"; + reg = <0x50>; + #mux-control-cells = <1>; + + idle-state = <MUX_IDLE_DISCONNECT MUX_IDLE_AS_IS 1>; + }; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux 2>; + + channels = "sync-1", "", "out"; + }; + + + /* + * Three parallel muxes with one mux controller, useful e.g. if + * the adc is differential, thus needing two signals to be muxed + * simultaneously for correct operation. + */ + &i2c0 { + pmux: mux-controller@50 { + compatible = "adi,adg792a"; + reg = <0x50>; + #mux-control-cells = <0>; + + idle-state = <1>; + }; + }; + + diff-adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&pmux>; + + channels = "sync-1", "", "out"; + }; diff --git a/Documentation/devicetree/bindings/mux/gpio-mux.txt b/Documentation/devicetree/bindings/mux/gpio-mux.txt new file mode 100644 index 000000000000..b8f746344d80 --- /dev/null +++ b/Documentation/devicetree/bindings/mux/gpio-mux.txt @@ -0,0 +1,69 @@ +GPIO-based multiplexer controller bindings + +Define what GPIO pins are used to control a multiplexer. Or several +multiplexers, if the same pins control more than one multiplexer. + +Required properties: +- compatible : "gpio-mux" +- mux-gpios : list of gpios used to control the multiplexer, least + significant bit first. +- #mux-control-cells : <0> +* Standard mux-controller bindings as decribed in mux-controller.txt + +Optional properties: +- idle-state : if present, the state the mux will have when idle. The + special state MUX_IDLE_AS_IS is the default. + +The multiplexer state is defined as the number represented by the +multiplexer GPIO pins, where the first pin is the least significant +bit. An active pin is a binary 1, an inactive pin is a binary 0. + +Example: + + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>, + <&pioA 1 GPIO_ACTIVE_HIGH>; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux>; + + channels = "sync-1", "in", "out", "sync-2"; + }; + + i2c-mux { + compatible = "i2c-mux"; + i2c-parent = <&i2c1>; + + mux-controls = <&mux>; + + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + /* ... */ + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + /* ... */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mux/mmio-mux.txt b/Documentation/devicetree/bindings/mux/mmio-mux.txt new file mode 100644 index 000000000000..a9bfb4d8b6ac --- /dev/null +++ b/Documentation/devicetree/bindings/mux/mmio-mux.txt @@ -0,0 +1,60 @@ +MMIO register bitfield-based multiplexer controller bindings + +Define register bitfields to be used to control multiplexers. The parent +device tree node must be a syscon node to provide register access. + +Required properties: +- compatible : "mmio-mux" +- #mux-control-cells : <1> +- mux-reg-masks : an array of register offset and pre-shifted bitfield mask + pairs, each describing a single mux control. +* Standard mux-controller bindings as decribed in mux-controller.txt + +Optional properties: +- idle-states : if present, the state the muxes will have when idle. The + special state MUX_IDLE_AS_IS is the default. + +The multiplexer state of each multiplexer is defined as the value of the +bitfield described by the corresponding register offset and bitfield mask pair +in the mux-reg-masks array, accessed through the parent syscon. + +Example: + + syscon { + compatible = "syscon"; + + mux: mux-controller { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + + mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ + <0x3 0x40>, /* 1: reg 0x3, bit 6 */ + idle-states = <MUX_IDLE_AS_IS>, <0>; + }; + }; + + video-mux { + compatible = "video-mux"; + mux-controls = <&mux 0>; + + ports { + /* inputs 0..3 */ + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + }; + port@2 { + reg = <2>; + }; + port@3 { + reg = <3>; + }; + + /* output */ + port@4 { + reg = <4>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mux/mux-controller.txt b/Documentation/devicetree/bindings/mux/mux-controller.txt new file mode 100644 index 000000000000..4f47e4bd2fa0 --- /dev/null +++ b/Documentation/devicetree/bindings/mux/mux-controller.txt @@ -0,0 +1,157 @@ +Common multiplexer controller bindings +====================================== + +A multiplexer (or mux) controller will have one, or several, consumer devices +that uses the mux controller. Thus, a mux controller can possibly control +several parallel multiplexers. Presumably there will be at least one +multiplexer needed by each consumer, but a single mux controller can of course +control several multiplexers for a single consumer. + +A mux controller provides a number of states to its consumers, and the state +space is a simple zero-based enumeration. I.e. 0-1 for a 2-way multiplexer, +0-7 for an 8-way multiplexer, etc. + + +Consumers +--------- + +Mux controller consumers should specify a list of mux controllers that they +want to use with a property containing a 'mux-ctrl-list': + + mux-ctrl-list ::= <single-mux-ctrl> [mux-ctrl-list] + single-mux-ctrl ::= <mux-ctrl-phandle> [mux-ctrl-specifier] + mux-ctrl-phandle : phandle to mux controller node + mux-ctrl-specifier : array of #mux-control-cells specifying the + given mux controller (controller specific) + +Mux controller properties should be named "mux-controls". The exact meaning of +each mux controller property must be documented in the device tree binding for +each consumer. An optional property "mux-control-names" may contain a list of +strings to label each of the mux controllers listed in the "mux-controls" +property. + +Drivers for devices that use more than a single mux controller can use the +"mux-control-names" property to map the name of the requested mux controller +to an index into the list given by the "mux-controls" property. + +mux-ctrl-specifier typically encodes the chip-relative mux controller number. +If the mux controller chip only provides a single mux controller, the +mux-ctrl-specifier can typically be left out. + +Example: + + /* One consumer of a 2-way mux controller (one GPIO-line) */ + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux>; + mux-control-names = "adc"; + + channels = "sync", "in"; + }; + +Note that in the example above, specifying the "mux-control-names" is redundant +because there is only one mux controller in the list. However, if the driver +for the consumer node in fact asks for a named mux controller, that name is of +course still required. + + /* + * Two consumers (one for an ADC line and one for an i2c bus) of + * parallel 4-way multiplexers controlled by the same two GPIO-lines. + */ + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>, + <&pioA 1 GPIO_ACTIVE_HIGH>; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux>; + + channels = "sync-1", "in", "out", "sync-2"; + }; + + i2c-mux { + compatible = "i2c-mux"; + i2c-parent = <&i2c1>; + + mux-controls = <&mux>; + + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + /* ... */ + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + /* ... */ + }; + }; + }; + + +Mux controller nodes +-------------------- + +Mux controller nodes must specify the number of cells used for the +specifier using the '#mux-control-cells' property. + +Optionally, mux controller nodes can also specify the state the mux should +have when it is idle. The idle-state property is used for this. If the +idle-state is not present, the mux controller is typically left as is when +it is idle. For multiplexer chips that expose several mux controllers, the +idle-state property is an array with one idle state for each mux controller. + +The special value (-1) may be used to indicate that the mux should be left +as is when it is idle. This is the default, but can still be useful for +mux controller chips with more than one mux controller, particularly when +there is a need to "step past" a mux controller and set some other idle +state for a mux controller with a higher index. + +Some mux controllers have the ability to disconnect the input/output of the +multiplexer. Using this disconnected high-impedance state as the idle state +is indicated with idle state (-2). + +These constants are available in + + #include <dt-bindings/mux/mux.h> + +as MUX_IDLE_AS_IS (-1) and MUX_IDLE_DISCONNECT (-2). + +An example mux controller node look like this (the adg972a chip is a triple +4-way multiplexer): + + mux: mux-controller@50 { + compatible = "adi,adg792a"; + reg = <0x50>; + #mux-control-cells = <1>; + + idle-state = <MUX_IDLE_DISCONNECT MUX_IDLE_AS_IS 2>; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index d6c6e41648d4..8ec2ca21adeb 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -34,7 +34,7 @@ Required properties: "brcm,bcm6328-switch" "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch" -See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional required and optional properties. Examples: diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt index 7ef9dbb08957..1d4d0f49c9d0 100644 --- a/Documentation/devicetree/bindings/net/dsa/marvell.txt +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -26,6 +26,10 @@ Optional properties: - interrupt-controller : Indicates the switch is itself an interrupt controller. This is used for the PHY interrupts. #interrupt-cells = <2> : Controller uses two cells, number and flag +- eeprom-length : Set to the length of an EEPROM connected to the + switch. Must be set if the switch can not detect + the presence and/or size of a connected EEPROM, + otherwise optional. - mdio : Container of PHY and devices on the switches MDIO bus. - mdio? : Container of PHYs and devices on the external MDIO diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt index 16c3a9501f5d..acfafc8e143c 100644 --- a/Documentation/devicetree/bindings/net/smsc911x.txt +++ b/Documentation/devicetree/bindings/net/smsc911x.txt @@ -27,6 +27,7 @@ Optional properties: of the device. On many systems this is wired high so the device goes out of reset at power-on, but if it is under program control, this optional GPIO can wake up in response to it. +- vdd33a-supply, vddvario-supply : 3.3V analog and IO logic power supplies Examples: diff --git a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt index 94aeeeabadd5..194926f77194 100644 --- a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt +++ b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Should be one of the following. - "rockchip,rk3066a-efuse" - for RK3066a SoCs. - "rockchip,rk3188-efuse" - for RK3188 SoCs. + - "rockchip,rk322x-efuse" - for RK322x SoCs. - "rockchip,rk3288-efuse" - for RK3288 SoCs. - "rockchip,rk3399-efuse" - for RK3399 SoCs. - reg: Should contain the registers location and exact eFuse size diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 63725498bd20..e36d261b9ba6 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -186,20 +186,20 @@ Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together. compatible = "operating-points-v2"; opp-shared; - opp@1000000000 { + opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <975000 970000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; - opp@1100000000 { + opp-1100000000 { opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <1000000 980000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; - opp@1200000000 { + opp-1200000000 { opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1025000>; clock-latency-ns = <290000>; @@ -265,20 +265,20 @@ independently. * independently. */ - opp@1000000000 { + opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <975000 970000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; - opp@1100000000 { + opp-1100000000 { opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <1000000 980000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; - opp@1200000000 { + opp-1200000000 { opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1025000>; opp-microamp = <90000; @@ -341,20 +341,20 @@ DVFS state together. compatible = "operating-points-v2"; opp-shared; - opp@1000000000 { + opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <975000 970000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; - opp@1100000000 { + opp-1100000000 { opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <1000000 980000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; - opp@1200000000 { + opp-1200000000 { opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1025000>; opp-microamp = <90000>; @@ -367,20 +367,20 @@ DVFS state together. compatible = "operating-points-v2"; opp-shared; - opp@1300000000 { + opp-1300000000 { opp-hz = /bits/ 64 <1300000000>; opp-microvolt = <1050000 1045000 1055000>; opp-microamp = <95000>; clock-latency-ns = <400000>; opp-suspend; }; - opp@1400000000 { + opp-1400000000 { opp-hz = /bits/ 64 <1400000000>; opp-microvolt = <1075000>; opp-microamp = <100000>; clock-latency-ns = <400000>; }; - opp@1500000000 { + opp-1500000000 { opp-hz = /bits/ 64 <1500000000>; opp-microvolt = <1100000 1010000 1110000>; opp-microamp = <95000>; @@ -409,7 +409,7 @@ Example 4: Handling multiple regulators compatible = "operating-points-v2"; opp-shared; - opp@1000000000 { + opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000>, /* Supply 0 */ <960000>, /* Supply 1 */ @@ -422,7 +422,7 @@ Example 4: Handling multiple regulators /* OR */ - opp@1000000000 { + opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <975000 970000 985000>, /* Supply 0 */ <965000 960000 975000>, /* Supply 1 */ @@ -435,7 +435,7 @@ Example 4: Handling multiple regulators /* OR */ - opp@1000000000 { + opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <975000 970000 985000>, /* Supply 0 */ <965000 960000 975000>, /* Supply 1 */ @@ -467,7 +467,7 @@ Example 5: opp-supported-hw status = "okay"; opp-shared; - opp@600000000 { + opp-600000000 { /* * Supports all substrate and process versions for 0xF * cuts, i.e. only first four cuts. @@ -478,7 +478,7 @@ Example 5: opp-supported-hw ... }; - opp@800000000 { + opp-800000000 { /* * Supports: * - cuts: only one, 6th cut (represented by 6th bit). @@ -510,7 +510,7 @@ Example 6: opp-microvolt-<name>, opp-microamp-<name>: compatible = "operating-points-v2"; opp-shared; - opp@1000000000 { + opp-1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt-slow = <915000 900000 925000>; opp-microvolt-fast = <975000 970000 985000>; @@ -518,7 +518,7 @@ Example 6: opp-microvolt-<name>, opp-microamp-<name>: opp-microamp-fast = <71000>; }; - opp@1200000000 { + opp-1200000000 { opp-hz = /bits/ 64 <1200000000>; opp-microvolt-slow = <915000 900000 925000>, /* Supply vcc0 */ <925000 910000 935000>; /* Supply vcc1 */ diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt index 09aeba94538d..32f057260351 100644 --- a/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt @@ -3,9 +3,10 @@ Driver for Broadcom Northstar USB 3.0 PHY Required properties: - compatible: one of: "brcm,ns-ax-usb3-phy", "brcm,ns-bx-usb3-phy". -- reg: register mappings for DMP (Device Management Plugin) and ChipCommon B - MMI. -- reg-names: "dmp" and "ccb-mii" +- reg: address of MDIO bus device +- usb3-dmp-syscon: phandle to syscon with DMP (Device Management Plugin) + registers +- #phy-cells: must be 0 Initialization of USB 3.0 PHY depends on Northstar version. There are currently three known series: Ax, Bx and Cx. @@ -15,9 +16,19 @@ Known B1: BCM4707 rev 6 Known C0: BCM47094 rev 0 Example: - usb3-phy { - compatible = "brcm,ns-ax-usb3-phy"; - reg = <0x18105000 0x1000>, <0x18003000 0x1000>; - reg-names = "dmp", "ccb-mii"; - #phy-cells = <0>; + mdio: mdio@0 { + reg = <0x0>; + #size-cells = <1>; + #address-cells = <0>; + + usb3-phy@10 { + compatible = "brcm,ns-ax-usb3-phy"; + reg = <0x10>; + usb3-dmp-syscon = <&usb3_dmp>; + #phy-cells = <0>; + }; + }; + + usb3_dmp: syscon@18105000 { + reg = <0x18105000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt new file mode 100644 index 000000000000..04f063aa7883 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt @@ -0,0 +1,30 @@ +BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY + +Required properties: + - compatible: brcm,ns2-drd-phy + - reg: offset and length of the NS2 PHY related registers. + - reg-names + The below registers must be provided. + icfg - for DRD ICFG configurations + rst-ctrl - for DRD IDM reset + crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset + usb2-strap - for port over current polarity reversal + - #phy-cells: Must be 0. No args required. + - vbus-gpios: vbus gpio binding + - id-gpios: id gpio binding + +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usbdrd_phy: phy@66000960 { + #phy-cells = <0>; + compatible = "brcm,ns2-drd-phy"; + reg = <0x66000960 0x24>, + <0x67012800 0x4>, + <0x6501d148 0x4>, + <0x664d0700 0x4>; + reg-names = "icfg", "rst-ctrl", + "crmu-ctrl", "usb2-strap"; + id-gpios = <&gpio_g 30 0>; + vbus-gpios = <&gpio_g 31 0>; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index 6ccce09d8bbf..97977cd29a98 100644 --- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -7,12 +7,13 @@ Required properties: "brcm,iproc-ns2-sata-phy" "brcm,iproc-nsp-sata-phy" "brcm,phy-sata3" + "brcm,iproc-sr-sata-phy" - address-cells: should be 1 - size-cells: should be 0 - reg: register ranges for the PHY PCB interface - reg-names: should be "phy" and "phy-ctrl" The "phy-ctrl" registers are only required for - "brcm,iproc-ns2-sata-phy". + "brcm,iproc-ns2-sata-phy" and "brcm,iproc-sr-sata-phy". Sub-nodes: Each port's PHY should be represented as a sub-node. @@ -23,8 +24,8 @@ Sub-nodes required properties: Sub-nodes optional properties: - brcm,enable-ssc: use spread spectrum clocking (SSC) on this port - This property is not applicable for "brcm,iproc-ns2-sata-phy" and - "brcm,iproc-nsp-sata-phy". + This property is not applicable for "brcm,iproc-ns2-sata-phy", + "brcm,iproc-nsp-sata-phy" and "brcm,iproc-sr-sata-phy". Example: sata-phy@f0458100 { diff --git a/Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt new file mode 100644 index 000000000000..a105494a0fc9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt @@ -0,0 +1,17 @@ +* Amlogic Meson GXL and GXM USB2 PHY binding + +Required properties: +- compatible: Should be "amlogic,meson-gxl-usb2-phy" +- reg: The base address and length of the registers +- #phys-cells: must be 0 (see phy-bindings.txt in this directory) + +Optional properties: +- phy-supply: see phy-bindings.txt in this directory + + +Example: + usb2_phy0: phy@78000 { + compatible = "amlogic,meson-gxl-usb2-phy"; + #phy-cells = <0>; + reg = <0x0 0x78000 0x0 0x20>; + }; diff --git a/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt index 5fa73b9d20f5..d81d73aea608 100644 --- a/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt +++ b/Documentation/devicetree/bindings/phy/meson8b-usb2-phy.txt @@ -1,7 +1,8 @@ -* Amlogic Meson8b and GXBB USB2 PHY +* Amlogic Meson8, Meson8b and GXBB USB2 PHY Required properties: - compatible: Depending on the platform this should be one of: + "amlogic,meson8-usb2-phy" "amlogic,meson8b-usb2-phy" "amlogic,meson-gxbb-usb2-phy" - reg: The base address and length of the registers diff --git a/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt b/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt new file mode 100644 index 000000000000..2eb9b2b69037 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt @@ -0,0 +1,40 @@ +Motorola CPCAP PMIC USB PHY binding + +Required properties: +compatible: Shall be either "motorola,cpcap-usb-phy" or + "motorola,mapphone-cpcap-usb-phy" +#phy-cells: Shall be 0 +interrupts: CPCAP PMIC interrupts used by the USB PHY +interrupt-names: Interrupt names +io-channels: IIO ADC channels used by the USB PHY +io-channel-names: IIO ADC channel names +vusb-supply: Regulator for the PHY + +Optional properties: +pinctrl: Optional alternate pin modes for the PHY +pinctrl-names: Names for optional pin modes +mode-gpios: Optional GPIOs for configuring alternate modes + +Example: +cpcap_usb2_phy: phy { + compatible = "motorola,mapphone-cpcap-usb-phy"; + pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>; + pinctrl-1 = <&usb_ulpi_pins>; + pinctrl-2 = <&usb_utmi_pins>; + pinctrl-3 = <&uart3_pins>; + pinctrl-names = "default", "ulpi", "utmi", "uart"; + #phy-cells = <0>; + interrupts-extended = < + &cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0 + &cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0 + &cpcap 48 1 + >; + interrupt-names = + "id_ground", "id_float", "se0conn", "vbusvld", + "sessvld", "sessend", "se1", "dm", "dp"; + mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH + &gpio1 0 GPIO_ACTIVE_HIGH>; + io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>; + io-channel-names = "vbus", "id"; + vusb-supply = <&vusb>; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt index e71a8d23f4a8..84d59b0db8df 100644 --- a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt @@ -2,6 +2,7 @@ ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK Required properties (phy (parent) node): - compatible : should be one of the listed compatibles: + * "rockchip,rk3228-usb2phy" * "rockchip,rk3328-usb2phy" * "rockchip,rk3366-usb2phy" * "rockchip,rk3399-usb2phy" diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt new file mode 100644 index 000000000000..f94cea48f6b1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt @@ -0,0 +1,46 @@ +* Renesas R-Car generation 3 USB 3.0 PHY + +This file provides information on what the device node for the R-Car generation +3 USB 3.0 PHY contains. +If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL +instead of USB3_CLK. However, if you don't want to these features, you don't +need this driver. + +Required properties: +- compatible: "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795 + SoC. + "renesas,r8a7796-usb3-phy" if the device is a part of an R8A7796 + SoC. + "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 compatible + device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: offset and length of the USB 3.0 PHY register block. +- clocks: A list of phandles and clock-specifier pairs. +- clock-names: Name of the clocks. + - The funcional clock must be "usb3-if". + - The usb3's external clock must be "usb3s_clk". + - The usb2's external clock must be "usb_extal". If you want to use the ssc, + the clock-frequency must not be 0. +- #phy-cells: see phy-bindings.txt in the same directory, must be <0>. + +Optional properties: +- renesas,ssc-range: Enable/disable spread spectrum clock (ssc) by using + the following values as u32: + - 0 (or the property doesn't exist): disable the ssc + - 4980: enable the ssc as -4980 ppm + - 4492: enable the ssc as -4492 ppm + - 4003: enable the ssc as -4003 ppm + +Example (R-Car H3): + + usb-phy@e65ee000 { + compatible = "renesas,r8a7795-usb3-phy", + "renesas,rcar-gen3-usb3-phy"; + reg = <0 0xe65ee000 0 0x90>; + clocks = <&cpg CPG_MOD 328>, <&usb3s0_clk>, <&usb_extal>; + clock-names = "usb3-if", "usb3s_clk", "usb_extal"; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index 71a3c134af1b..f01d154090da 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -247,7 +247,6 @@ bias-bus-hold - latch weakly bias-pull-up - pull up the pin bias-pull-down - pull down the pin bias-pull-pin-default - use pin-default pull state -bi-directional - pin supports simultaneous input/output operations drive-push-pull - drive actively high and low drive-open-drain - drive with open drain drive-open-source - drive with open source @@ -260,7 +259,6 @@ input-debounce - debounce mode with debound time X power-source - select between different power supplies low-power-enable - enable low power mode low-power-disable - disable low power mode -output-enable - enable output on pin regardless of output value output-low - set the pin to output mode with low level output-high - set the pin to output mode with high level slew-rate - set the slew rate diff --git a/Documentation/devicetree/bindings/power/actions,owl-sps.txt b/Documentation/devicetree/bindings/power/actions,owl-sps.txt new file mode 100644 index 000000000000..007b9a7ae723 --- /dev/null +++ b/Documentation/devicetree/bindings/power/actions,owl-sps.txt @@ -0,0 +1,17 @@ +Actions Semi Owl Smart Power System (SPS) + +Required properties: +- compatible : "actions,s500-sps" for S500 +- reg : Offset and length of the register set for the device. +- #power-domain-cells : Must be 1. + See macros in: + include/dt-bindings/power/owl-s500-powergate.h for S500 + + +Example: + + sps: power-controller@b01b0100 { + compatible = "actions,s500-sps"; + reg = <0xb01b0100 0x100>; + #power-domain-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index d3a5a93a65cd..43c21fb04564 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -32,6 +32,7 @@ SoC is on the same page. Required properties: - compatible: should be one of: - "rockchip,rk3188-io-voltage-domain" for rk3188 + - "rockchip,rk3228-io-voltage-domain" for rk3228 - "rockchip,rk3288-io-voltage-domain" for rk3288 - "rockchip,rk3328-io-voltage-domain" for rk3328 - "rockchip,rk3368-io-voltage-domain" for rk3368 @@ -59,6 +60,12 @@ Possible supplies for rk3188: - vccio1-supply: The supply connected to VCCIO1. Sometimes also labeled VCCIO1 and VCCIO2. +Possible supplies for rk3228: +- vccio1-supply: The supply connected to VCCIO1. +- vccio2-supply: The supply connected to VCCIO2. +- vccio3-supply: The supply connected to VCCIO3. +- vccio4-supply: The supply connected to VCCIO4. + Possible supplies for rk3288: - audio-supply: The supply connected to APIO4_VDD. - bb-supply: The supply connected to APIO5_VDD. diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt new file mode 100644 index 000000000000..f4d3b4a10b43 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/battery.txt @@ -0,0 +1,57 @@ +Battery Characteristics + +The devicetree battery node provides static battery characteristics. +In smart batteries, these are typically stored in non-volatile memory +on a fuel gauge chip. The battery node should be used where there is +no appropriate non-volatile memory, or it is unprogrammed/incorrect. + +Upstream dts files should not include battery nodes, unless the battery +represented cannot easily be replaced in the system by one of a +different type. This prevents unpredictable, potentially harmful, +behavior should a replacement that changes the battery type occur +without a corresponding update to the dtb. + +Required Properties: + - compatible: Must be "simple-battery" + +Optional Properties: + - voltage-min-design-microvolt: drained battery voltage + - energy-full-design-microwatt-hours: battery design energy + - charge-full-design-microamp-hours: battery design capacity + - precharge-current-microamp: current for pre-charge phase + - charge-term-current-microamp: current for charge termination phase + - constant-charge-current-max-microamp: maximum constant input current + - constant-charge-voltage-max-microvolt: maximum constant input voltage + +Battery properties are named, where possible, for the corresponding +elements in enum power_supply_property, defined in +https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/power_supply.h + +Batteries must be referenced by chargers and/or fuel-gauges +using a phandle. The phandle's property should be named +"monitored-battery". + +Example: + + bat: battery { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3200000>; + energy-full-design-microwatt-hours = <5290000>; + charge-full-design-microamp-hours = <1430000>; + precharge-current-microamp = <256000>; + charge-term-current-microamp = <128000>; + constant-charge-current-max-microamp = <900000>; + constant-charge-voltage-max-microvolt = <4200000>; + }; + + charger: charger@11 { + .... + monitored-battery = <&bat>; + ... + }; + + fuel_gauge: fuel-gauge@22 { + .... + monitored-battery = <&bat>; + ... + }; diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt index b0c95ef63e68..6858e1a804ad 100644 --- a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt +++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt @@ -1,7 +1,7 @@ -Binding for TI BQ27XXX fuel gauge family +TI BQ27XXX fuel gauge family Required properties: -- compatible: Should contain one of the following: +- compatible: contains one of the following: * "ti,bq27200" - BQ27200 * "ti,bq27210" - BQ27210 * "ti,bq27500" - deprecated, use revision specific property below @@ -26,11 +26,28 @@ Required properties: * "ti,bq27425" - BQ27425 * "ti,bq27441" - BQ27441 * "ti,bq27621" - BQ27621 -- reg: integer, i2c address of the device. +- reg: integer, I2C address of the fuel gauge. + +Optional properties: +- monitored-battery: phandle of battery characteristics node + The fuel gauge uses the following battery properties: + + energy-full-design-microwatt-hours + + charge-full-design-microamp-hours + + voltage-min-design-microvolt + Both or neither of the *-full-design-*-hours properties must be set. + See Documentation/devicetree/bindings/power/supply/battery.txt Example: -bq27510g3 { - compatible = "ti,bq27510g3"; - reg = <0x55>; -}; + bat: battery { + compatible = "simple-battery"; + voltage-min-design-microvolt = <3200000>; + energy-full-design-microwatt-hours = <5290000>; + charge-full-design-microamp-hours = <1430000>; + }; + + bq27510g3: fuel-gauge@55 { + compatible = "ti,bq27510g3"; + reg = <0x55>; + monitored-battery = <&bat>; + }; diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt new file mode 100644 index 000000000000..a04efa22da01 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt @@ -0,0 +1,31 @@ +Motorola CPCAP PMIC battery driver binding + +Required properties: +- compatible: Shall be "motorola,cpcap-battery" +- interrupts: Interrupt specifier for each name in interrupt-names +- interrupt-names: Should contain the following entries: + "lowbph", "lowbpl", "chrgcurr1", "battdetb" +- io-channels: IIO ADC channel specifier for each name in io-channel-names +- io-channel-names: Should contain the following entries: + "battdetb", "battp", "chg_isense", "batti" +- power-supplies: List of phandles for power-supplying devices, as + described in power_supply.txt. Typically a reference + to cpcap_charger. + +Example: + +cpcap_battery: battery { + compatible = "motorola,cpcap-battery"; + interrupts-extended = < + &cpcap 5 0 &cpcap 3 0 + &cpcap 20 0 &cpcap 54 0 + >; + interrupt-names = + "lowbph", "lowbpl", + "chrgcurr1", "battdetb"; + io-channels = <&cpcap_adc 0 &cpcap_adc 1 + &cpcap_adc 5 &cpcap_adc 6>; + io-channel-names = "battdetb", "battp", + "chg_isense", "batti"; + power-supplies = <&cpcap_charger>; +}; diff --git a/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt new file mode 100644 index 000000000000..71f2840e8209 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt @@ -0,0 +1,27 @@ +ltc3651-charger + +Required properties: + - compatible: "lltc,ltc3651-charger" + - lltc,acpr-gpios: Connect to ACPR output. See remark below. + +Optional properties: + - lltc,fault-gpios: Connect to FAULT output. See remark below. + - lltc,chrg-gpios: Connect to CHRG output. See remark below. + +The ltc3651 outputs are open-drain type and active low. The driver assumes the +GPIO reports "active" when the output is asserted, so if the pins have been +connected directly, the GPIO flags should be set to active low also. + +The driver will attempt to aquire interrupts for all GPIOs to detect changes in +line state. If the system is not capabale of providing interrupts, the driver +cannot report changes and userspace will need to periodically read the sysfs +attributes to detect changes. + +Example: + + charger: battery-charger { + compatible = "lltc,ltc3651-charger"; + lltc,acpr-gpios = <&gpio0 68 GPIO_ACTIVE_LOW>; + lltc,fault-gpios = <&gpio0 64 GPIO_ACTIVE_LOW>; + lltc,chrg-gpios = <&gpio0 63 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/power/max8903-charger.txt b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt index f0f4e12b076e..f0f4e12b076e 100644 --- a/Documentation/devicetree/bindings/power/max8903-charger.txt +++ b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt diff --git a/Documentation/devicetree/bindings/power_supply/maxim,max14656.txt b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt index e03e85ae6572..e03e85ae6572 100644 --- a/Documentation/devicetree/bindings/power_supply/maxim,max14656.txt +++ b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt diff --git a/Documentation/devicetree/bindings/property-units.txt b/Documentation/devicetree/bindings/property-units.txt index 12278d79f6c0..0849618a9df0 100644 --- a/Documentation/devicetree/bindings/property-units.txt +++ b/Documentation/devicetree/bindings/property-units.txt @@ -25,8 +25,10 @@ Distance Electricity ---------------------------------------- -microamp : micro amps +-microamp-hours : micro amp-hours -ohms : Ohms -micro-ohms : micro Ohms +-microwatt-hours: micro Watt-hours -microvolt : micro volts Temperature diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index d18edb075e1c..378f6dc8b8bd 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -24,6 +24,14 @@ Optional properties: - regulator-settling-time-us: Settling time, in microseconds, for voltage change if regulator have the constant time for any level voltage change. This is useful when regulator have exponential voltage change. +- regulator-settling-time-up-us: Settling time, in microseconds, for voltage + increase if the regulator needs a constant time to settle after voltage + increases of any level. This is useful for regulators with exponential + voltage changes. +- regulator-settling-time-down-us: Settling time, in microseconds, for voltage + decrease if the regulator needs a constant time to settle after voltage + decreases of any level. This is useful for regulators with exponential + voltage changes. - regulator-soft-start: Enable soft start so that voltage ramps slowly - regulator-state-mem sub-root node for Suspend-to-RAM mode : suspend to memory, the device goes to sleep, but all data stored in memory, diff --git a/Documentation/devicetree/bindings/reset/ti,sci-reset.txt b/Documentation/devicetree/bindings/reset/ti,sci-reset.txt new file mode 100644 index 000000000000..8b1cf022f18a --- /dev/null +++ b/Documentation/devicetree/bindings/reset/ti,sci-reset.txt @@ -0,0 +1,62 @@ +Texas Instruments System Control Interface (TI-SCI) Reset Controller +===================================================================== + +Some TI SoCs contain a system controller (like the Power Management Micro +Controller (PMMC) on Keystone 66AK2G SoC) that are responsible for controlling +the state of the various hardware modules present on the SoC. Communication +between the host processor running an OS and the system controller happens +through a protocol called TI System Control Interface (TI-SCI protocol). +For TI SCI details, please refer to the document, +Documentation/devicetree/bindings/arm/keystone/ti,sci.txt + +TI-SCI Reset Controller Node +============================ +This reset controller node uses the TI SCI protocol to perform the reset +management of various hardware modules present on the SoC. Must be a child +node of the associated TI-SCI system controller node. + +Required properties: +-------------------- + - compatible : Should be "ti,sci-reset" + - #reset-cells : Should be 2. Please see the reset consumer node below for + usage details. + +TI-SCI Reset Consumer Nodes +=========================== +Each of the reset consumer nodes should have the following properties, +in addition to their own properties. + +Required properties: +-------------------- + - resets : A phandle and reset specifier pair, one pair for each reset + signal that affects the device, or that the device manages. + The phandle should point to the TI-SCI reset controller node, + and the reset specifier should have 2 cell-values. The first + cell should contain the device ID. The second cell should + contain the reset mask value used by system controller. + Please refer to the protocol documentation for these values + to be used for different devices, + http://processors.wiki.ti.com/index.php/TISCI#66AK2G02_Data + +Please also refer to Documentation/devicetree/bindings/reset/reset.txt for +common reset controller usage by consumers. + +Example: +-------- +The following example demonstrates both a TI-SCI reset controller node and a +consumer (a DSP device) on the 66AK2G SoC. + +pmmc: pmmc { + compatible = "ti,k2g-sci"; + + k2g_reset: reset-controller { + compatible = "ti,sci-reset"; + #reset-cells = <2>; + }; +}; + +dsp0: dsp@10800000 { + ... + resets = <&k2g_reset 0x0046 0x1>; + ... +}; diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 10276a46ecef..419ff6c0a47f 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -20,6 +20,8 @@ Required properties: - "fsl,16550-FIFO64" - "fsl,ns16550" - "ti,da830-uart" + - "aspeed,ast2400-vuart" + - "aspeed,ast2500-vuart" - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. @@ -45,6 +47,7 @@ Optional properties: property. - tx-threshold: Specify the TX FIFO low water indication for parts with programmable TX FIFO thresholds. +- resets : phandle + reset specifier pairs Note: * fsl,ns16550: diff --git a/Documentation/devicetree/bindings/serial/actions,owl-uart.txt b/Documentation/devicetree/bindings/serial/actions,owl-uart.txt new file mode 100644 index 000000000000..aa873eada02d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/actions,owl-uart.txt @@ -0,0 +1,16 @@ +Actions Semi Owl UART + +Required properties: +- compatible : "actions,s500-uart", "actions,owl-uart" for S500 + "actions,s900-uart", "actions,owl-uart" for S900 +- reg : Offset and length of the register set for the device. +- interrupts : Should contain UART interrupt. + + +Example: + + uart3: serial@b0126000 { + compatible = "actions,s500-uart", "actions,owl-uart"; + reg = <0xb0126000 0x1000>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt new file mode 100644 index 000000000000..8ff65fa632fd --- /dev/null +++ b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt @@ -0,0 +1,38 @@ +Amlogic Meson SoC UART Serial Interface +======================================= + +The Amlogic Meson SoC UART Serial Interface is present on a large range +of SoCs, and can be present either in the "Always-On" power domain or the +"Everything-Else" power domain. + +The particularity of the "Always-On" Serial Interface is that the hardware +is active since power-on and does not need any clock gating and is usable +as very early serial console. + +Required properties: +- compatible : compatible: value should be different for each SoC family as : + - Meson6 : "amlogic,meson6-uart" + - Meson8 : "amlogic,meson8-uart" + - Meson8b : "amlogic,meson8b-uart" + - GX (GXBB, GXL, GXM) : "amlogic,meson-gx-uart" + eventually followed by : "amlogic,meson-ao-uart" if this UART interface + is in the "Always-On" power domain. +- reg : offset and length of the register set for the device. +- interrupts : identifier to the device interrupt +- clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock names. +- clocks-names : + * "xtal" for external xtal clock identifier + * "pclk" for the bus core clock, either the clk81 clock or the gate clock + * "baud" for the source of the baudrate generator, can be either the xtal + or the pclk. + +e.g. +uart_A: serial@84c0 { + compatible = "amlogic,meson-gx-uart"; + reg = <0x0 0x84c0 0x0 0x14>; + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>; + /* Use xtal as baud rate clock source */ + clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>; + clock-names = "xtal", "pclk", "baud"; +}; diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt index 574c3a2c77d5..e6b572409cf5 100644 --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -9,6 +9,7 @@ Optional properties: - fsl,irda-mode : Indicate the uart supports irda mode - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works in DCE mode by default. +- fsl,dma-size : Indicate the size of the DMA buffer and its periods Please check Documentation/devicetree/bindings/serial/serial.txt for the complete list of generic properties. @@ -28,4 +29,5 @@ uart1: serial@73fbc000 { interrupts = <31>; uart-has-rtscts; fsl,dte-mode; + fsl,dma-size = <1024 4>; }; diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt index c95005efbcb8..a1252a047f78 100644 --- a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt @@ -6,6 +6,8 @@ Required properties: on Vybrid vf610 SoC with 8-bit register organization - "fsl,ls1021a-lpuart" for lpuart compatible with the one integrated on LS1021A SoC with 32-bit big-endian register organization + - "fsl,imx7ulp-lpuart" for lpuart compatible with the one integrated + on i.MX7ULP SoC with 32-bit little-endian register organization - reg : Address and length of the register set for the device - interrupts : Should contain uart interrupt - clocks : phandle + clock specifier pairs, one for each entry in clock-names diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index dc975064fa27..64ee489571c4 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -38,6 +38,8 @@ Optional properties: specifiers, one for transmission, and one for reception. - dma-names : Must contain a list of two DMA names, "tx" and "rx". +- spi-slave : Empty property indicating the SPI controller is used + in slave mode. - renesas,dtdl : delay sync signal (setup) in transmit mode. Must contain one of the following values: 0 (no bit delay) diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 4b1d6e74c744..1f6e86f787ef 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -1,17 +1,23 @@ SPI (Serial Peripheral Interface) busses -SPI busses can be described with a node for the SPI master device -and a set of child nodes for each SPI slave on the bus. For this -discussion, it is assumed that the system's SPI controller is in -SPI master mode. This binding does not describe SPI controllers -in slave mode. +SPI busses can be described with a node for the SPI controller device +and a set of child nodes for each SPI slave on the bus. The system's SPI +controller may be described for use in SPI master mode or in SPI slave mode, +but not for both at the same time. -The SPI master node requires the following properties: +The SPI controller node requires the following properties: +- compatible - Name of SPI bus controller following generic names + recommended practice. + +In master mode, the SPI controller node requires the following additional +properties: - #address-cells - number of cells required to define a chip select address on the SPI bus. - #size-cells - should be zero. -- compatible - name of SPI bus controller following generic names - recommended practice. + +In slave mode, the SPI controller node requires one additional property: +- spi-slave - Empty property. + No other properties are required in the SPI bus node. It is assumed that a driver for an SPI bus device will understand that it is an SPI bus. However, the binding does not attempt to define the specific method for @@ -21,7 +27,7 @@ assumption that board specific platform code will be used to manage chip selects. Individual drivers can define additional properties to support describing the chip select layout. -Optional properties: +Optional properties (master mode only): - cs-gpios - gpios chip select. - num-cs - total number of chipselects. @@ -41,28 +47,36 @@ cs1 : native cs2 : &gpio1 1 0 cs3 : &gpio1 2 0 -SPI slave nodes must be children of the SPI master node and can -contain the following properties. -- reg - (required) chip select address of device. -- compatible - (required) name of SPI device following generic names - recommended practice. -- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz. -- spi-cpol - (optional) Empty property indicating device requires - inverse clock polarity (CPOL) mode. -- spi-cpha - (optional) Empty property indicating device requires - shifted clock phase (CPHA) mode. -- spi-cs-high - (optional) Empty property indicating device requires - chip select active high. -- spi-3wire - (optional) Empty property indicating device requires - 3-wire mode. -- spi-lsb-first - (optional) Empty property indicating device requires - LSB first mode. -- spi-tx-bus-width - (optional) The bus width (number of data wires) that is - used for MOSI. Defaults to 1 if not present. -- spi-rx-bus-width - (optional) The bus width (number of data wires) that is - used for MISO. Defaults to 1 if not present. -- spi-rx-delay-us - (optional) Microsecond delay after a read transfer. -- spi-tx-delay-us - (optional) Microsecond delay after a write transfer. + +SPI slave nodes must be children of the SPI controller node. + +In master mode, one or more slave nodes (up to the number of chip selects) can +be present. Required properties are: +- compatible - Name of SPI device following generic names recommended + practice. +- reg - Chip select address of device. +- spi-max-frequency - Maximum SPI clocking speed of device in Hz. + +In slave mode, the (single) slave node is optional. +If present, it must be called "slave". Required properties are: +- compatible - Name of SPI device following generic names recommended + practice. + +All slave nodes can contain the following optional properties: +- spi-cpol - Empty property indicating device requires inverse clock + polarity (CPOL) mode. +- spi-cpha - Empty property indicating device requires shifted clock + phase (CPHA) mode. +- spi-cs-high - Empty property indicating device requires chip select + active high. +- spi-3wire - Empty property indicating device requires 3-wire mode. +- spi-lsb-first - Empty property indicating device requires LSB first mode. +- spi-tx-bus-width - The bus width (number of data wires) that is used for MOSI. + Defaults to 1 if not present. +- spi-rx-bus-width - The bus width (number of data wires) that is used for MISO. + Defaults to 1 if not present. +- spi-rx-delay-us - Microsecond delay after a read transfer. +- spi-tx-delay-us - Microsecond delay after a write transfer. Some SPI controllers and devices support Dual and Quad SPI transfer mode. It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4 diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt index dc6d0313324a..825c39cae74a 100644 --- a/Documentation/devicetree/bindings/spi/spi-meson.txt +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -20,3 +20,34 @@ Required properties: #address-cells = <1>; #size-cells = <0>; }; + +* SPICC (SPI Communication Controller) + +The Meson SPICC is generic SPI controller for general purpose Full-Duplex +communications with dedicated 16 words RX/TX PIO FIFOs. + +Required properties: + - compatible: should be "amlogic,meson-gx-spicc" on Amlogic GX SoCs. + - reg: physical base address and length of the controller registers + - interrupts: The interrupt specifier + - clock-names: Must contain "core" + - clocks: phandle of the input clock for the baud rate generator + - #address-cells: should be 1 + - #size-cells: should be 0 + +Optional properties: + - resets: phandle of the internal reset line + +See ../spi/spi-bus.txt for more details on SPI bus master and slave devices +required and optional properties. + +Example : + spi@c1108d80 { + compatible = "amlogic,meson-gx-spicc"; + reg = <0xc1108d80 0x80>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "core"; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index e43f4cf4cf35..e0318cf92d73 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -3,7 +3,9 @@ Binding for MTK SPI controller Required properties: - compatible: should be one of the following. - mediatek,mt2701-spi: for mt2701 platforms + - mediatek,mt2712-spi: for mt2712 platforms - mediatek,mt6589-spi: for mt6589 platforms + - mediatek,mt7622-spi: for mt7622 platforms - mediatek,mt8135-spi: for mt8135 platforms - mediatek,mt8173-spi: for mt8173 platforms diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt new file mode 100644 index 000000000000..1b3fa2c119d5 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-stm32.txt @@ -0,0 +1,59 @@ +STMicroelectronics STM32 SPI Controller + +The STM32 SPI controller is used to communicate with external devices using +the Serial Peripheral Interface. It supports full-duplex, half-duplex and +simplex synchronous serial communication with external devices. It supports +from 4 to 32-bit data size. Although it can be configured as master or slave, +only master is supported by the driver. + +Required properties: +- compatible: Must be "st,stm32h7-spi". +- reg: Offset and length of the device's register set. +- interrupts: Must contain the interrupt id. +- clocks: Must contain an entry for spiclk (which feeds the internal clock + generator). +- #address-cells: Number of cells required to define a chip select address. +- #size-cells: Should be zero. + +Optional properties: +- resets: Must contain the phandle to the reset controller. +- A pinctrl state named "default" may be defined to set pins in mode of + operation for SPI transfer. +- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the + STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt. +- dma-names: DMA request names should include "tx" and "rx" if present. +- cs-gpios: list of GPIO chip selects. See the SPI bus bindings, + Documentation/devicetree/bindings/spi/spi-bus.txt + + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Optional properties: +- st,spi-midi-ns: (Master Inter-Data Idleness) minimum time delay in + nanoseconds inserted between two consecutive data frames. + + +Example: + spi2: spi@40003800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32h7-spi"; + reg = <0x40003800 0x400>; + interrupts = <36>; + clocks = <&rcc SPI2_CK>; + resets = <&rcc 1166>; + dmas = <&dmamux1 0 39 0x400 0x01>, + <&dmamux1 1 40 0x400 0x01>; + dma-names = "rx", "tx"; + pinctrl-0 = <&spi2_pins_b>; + pinctrl-names = "default"; + cs-gpios = <&gpioa 11 0>; + + aardvark@0 { + compatible = "totalphase,aardvark"; + reg = <0>; + spi-max-frequency = <4000000>; + st,spi-midi-ns = <4000>; + }; + }; diff --git a/Documentation/devicetree/bindings/timer/actions,owl-timer.txt b/Documentation/devicetree/bindings/timer/actions,owl-timer.txt new file mode 100644 index 000000000000..e3c28da80cb2 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/actions,owl-timer.txt @@ -0,0 +1,20 @@ +Actions Semi Owl Timer + +Required properties: +- compatible : "actions,s500-timer" for S500 + "actions,s900-timer" for S900 +- reg : Offset and length of the register set for the device. +- interrupts : Should contain the interrupts. +- interrupt-names : Valid names are: "2hz0", "2hz1", + "timer0", "timer1", "timer2", "timer3" + See ../resource-names.txt + +Example: + + timer@b0168000 { + compatible = "actions,s500-timer"; + reg = <0xb0168000 0x100>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "timer0", "timer1"; + }; diff --git a/Documentation/devicetree/bindings/timer/faraday,fttmr010.txt b/Documentation/devicetree/bindings/timer/faraday,fttmr010.txt index b73ca6cd07f8..195792270414 100644 --- a/Documentation/devicetree/bindings/timer/faraday,fttmr010.txt +++ b/Documentation/devicetree/bindings/timer/faraday,fttmr010.txt @@ -7,7 +7,11 @@ Required properties: - compatible : Must be one of "faraday,fttmr010" - "cortina,gemini-timer" + "cortina,gemini-timer", "faraday,fttmr010" + "moxa,moxart-timer", "faraday,fttmr010" + "aspeed,ast2400-timer" + "aspeed,ast2500-timer" + - reg : Should contain registers location and length - interrupts : Should contain the three timer interrupts usually with flags for falling edge diff --git a/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt b/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt deleted file mode 100644 index e207c11630af..000000000000 --- a/Documentation/devicetree/bindings/timer/moxa,moxart-timer.txt +++ /dev/null @@ -1,19 +0,0 @@ -MOXA ART timer - -Required properties: - -- compatible : Must be one of: - - "moxa,moxart-timer" - - "aspeed,ast2400-timer" -- reg : Should contain registers location and length -- interrupts : Should contain the timer interrupt number -- clocks : Should contain phandle for the clock that drives the counter - -Example: - - timer: timer@98400000 { - compatible = "moxa,moxart-timer"; - reg = <0x98400000 0x42>; - interrupts = <19 1>; - clocks = <&coreclk>; - }; diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt index 3e0a34c88e07..35f406dd86b6 100644 --- a/Documentation/devicetree/bindings/trivial-devices.txt +++ b/Documentation/devicetree/bindings/trivial-devices.txt @@ -55,6 +55,7 @@ gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire In infineon,slb9635tt Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz) infineon,slb9645tt Infineon SLB9645 I2C TPM (new protocol, max 400khz) isil,isl29028 Intersil ISL29028 Ambient Light and Proximity Sensor +isil,isl29030 Intersil ISL29030 Ambient Light and Proximity Sensor maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 00bea038639e..fcf199b64d3d 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -10,6 +10,7 @@ Required properties: - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs; - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs; + - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs; - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs; - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs; - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index f658f394c2d3..52fb41046b34 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -45,6 +45,8 @@ Optional properties: a free-running PHY clock. - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power from P0 to P1/P2/P3 without delay. + - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check + during HS transmit. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold diff --git a/Documentation/devicetree/bindings/usb/iproc-udc.txt b/Documentation/devicetree/bindings/usb/iproc-udc.txt new file mode 100644 index 000000000000..272d7faf1a97 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/iproc-udc.txt @@ -0,0 +1,21 @@ +Broadcom IPROC USB Device controller. + +The device node is used for UDCs integrated into Broadcom's +iProc family (Northstar2, Cygnus) of SoCs'. The UDC is based +on Synopsys Designware Cores AHB Subsystem Device Controller +IP. + +Required properties: + - compatible: Add the compatibility strings for supported platforms. + For Broadcom NS2 platform, add "brcm,ns2-udc","brcm,iproc-udc". + For Broadcom Cygnus platform, add "brcm,cygnus-udc", "brcm,iproc-udc". + - reg: Offset and length of UDC register set + - interrupts: description of interrupt line + - phys: phandle to phy node. + +Example: + udc_dwc: usb@664e0000 { + compatible = "brcm,ns2-udc", "brcm,iproc-udc"; + reg = <0x664e0000 0x2000>; + interrupts = <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbdrd_phy>; diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index 9df456968596..e8766b08c93b 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -10,6 +10,7 @@ Optional properties: - big-endian-desc : boolean, set this for hcds with big-endian descriptors - big-endian : boolean, for hcds with big-endian-regs + big-endian-desc - no-big-frame-no : boolean, set if frame_no lives in bits [15:0] of HCCA +- remote-wakeup-connected: remote wakeup is wired on the platform - num-ports : u32, to override the detected port count - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 8e5e87869a85..286f4e1e111f 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -5,6 +5,7 @@ using them to avoid name-space collisions. abcn Abracon Corporation abilis Abilis Systems +actions Actions Semiconductor Co., Ltd. active-semi Active-Semi International Inc ad Avionic Design GmbH adapteva Adapteva, Inc. |