diff options
Diffstat (limited to 'Documentation/devicetree')
51 files changed, 1131 insertions, 72 deletions
diff --git a/Documentation/devicetree/bindings/ata/brcm,sata-brcmstb.txt b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt index 60872838f1ad..0a5b3b47f217 100644 --- a/Documentation/devicetree/bindings/ata/brcm,sata-brcmstb.txt +++ b/Documentation/devicetree/bindings/ata/brcm,sata-brcm.txt @@ -1,13 +1,14 @@ -* Broadcom SATA3 AHCI Controller for STB +* Broadcom SATA3 AHCI Controller SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. Required properties: - compatible : should be one or more of - "brcm,bcm7425-ahci" - "brcm,bcm7445-ahci" - "brcm,sata3-ahci" + "brcm,bcm7425-ahci" + "brcm,bcm7445-ahci" + "brcm,bcm-nsp-ahci" + "brcm,sata3-ahci" - reg : register mappings for AHCI and SATA_TOP_CTRL - reg-names : "ahci" and "top-ctrl" - interrupts : interrupt mapping for SATA IRQ diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt index 0a175d991b52..a407462c885e 100644 --- a/Documentation/devicetree/bindings/display/imx/ldb.txt +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -62,6 +62,7 @@ Required properties: display-timings are used instead. Optional properties (required if display-timings are used): + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - display-timings : A node that describes the display timings as defined in Documentation/devicetree/bindings/display/display-timing.txt. - fsl,data-mapping : should be "spwg" or "jeida" diff --git a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt index e27341f8a4c7..7f3d94ae81ff 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt @@ -46,7 +46,8 @@ Optional properties: The second cell represents the MICBIAS to be used. The third cell represents the value of the micd-pol-gpio pin. - - wlf,gpsw : Settings for the general purpose switch + - wlf,gpsw : Settings for the general purpose switch, set as one of the + ARIZONA_GPSW_XXX defines. Example: diff --git a/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt index 94ae9f82dcf8..fd42e7280f72 100644 --- a/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/cirrus,clps711x-mctrl-gpio.txt @@ -1,7 +1,7 @@ * ARM Cirrus Logic CLPS711X SYSFLG1 MCTRL GPIOs Required properties: -- compatible: Should contain "cirrus,clps711x-mctrl-gpio". +- compatible: Should contain "cirrus,ep7209-mctrl-gpio". - gpio-controller: Marks the device node as a gpio controller. - #gpio-cells: Should be two. The first cell is the pin number and the second cell is used to specify the gpio polarity: @@ -11,7 +11,7 @@ Required properties: Example: sysgpio: sysgpio { compatible = "cirrus,ep7312-mctrl-gpio", - "cirrus,clps711x-mctrl-gpio"; + "cirrus,ep7209-mctrl-gpio"; gpio-controller; #gpio-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt index e0d0446a6b78..0a304ad29d81 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-clps711x.txt @@ -1,7 +1,7 @@ Cirrus Logic CLPS711X GPIO controller Required properties: -- compatible: Should be "cirrus,clps711x-gpio" +- compatible: Should be "cirrus,ep7209-gpio" - reg: Physical base GPIO controller registers location and length. There should be two registers, first is DATA register, the second is DIRECTION. @@ -21,7 +21,7 @@ aliases { }; porta: gpio@80000000 { - compatible = "cirrus,clps711x-gpio"; + compatible = "cirrus,ep7312-gpio","cirrus,ep7209-gpio"; reg = <0x80000000 0x1>, <0x80000040 0x1>; gpio-controller; #gpio-cells = <2>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-max77620.txt b/Documentation/devicetree/bindings/gpio/gpio-max77620.txt new file mode 100644 index 000000000000..410e716fd3d2 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-max77620.txt @@ -0,0 +1,25 @@ +GPIO driver for MAX77620 Power management IC from Maxim Semiconductor. + +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Required properties: +------------------- +- gpio-controller : Marks the device node as a gpio controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +For more details, please refer generic GPIO DT binding document +<devicetree/bindings/gpio/gpio.txt>. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + compatible = "maxim,max77620"; + + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index 6b4a98f74be3..08dd15f89ba9 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -21,6 +21,7 @@ Required properties: maxim,max7313 maxim,max7315 ti,pca6107 + ti,pca9536 ti,tca6408 ti,tca6416 ti,tca6424 diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index f60e2f477e93..8da26b35b5c3 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -7,6 +7,7 @@ Required Properties: - "renesas,gpio-r8a7779": for R8A7779 (R-Car H1) compatible GPIO controller. - "renesas,gpio-r8a7790": for R8A7790 (R-Car H2) compatible GPIO controller. - "renesas,gpio-r8a7791": for R8A7791 (R-Car M2-W) compatible GPIO controller. + - "renesas,gpio-r8a7792": for R8A7792 (R-Car V2H) compatible GPIO controller. - "renesas,gpio-r8a7793": for R8A7793 (R-Car M2-N) compatible GPIO controller. - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller. diff --git a/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt b/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt new file mode 100644 index 000000000000..59b38557f1bb --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/apm-xgene-hwmon.txt @@ -0,0 +1,14 @@ +APM X-Gene hwmon driver + +APM X-Gene SOC sensors are accessed over the "SLIMpro" mailbox. + +Required properties : + - compatible : should be "apm,xgene-slimpro-hwmon" + - mboxes : use the label reference for the mailbox as the first parameter. + The second parameter is the channel number. + +Example : + hwmonslimpro { + compatible = "apm,xgene-slimpro-hwmon"; + mboxes = <&mailbox 7>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ina2xx.txt b/Documentation/devicetree/bindings/hwmon/ina2xx.txt index 9bcd5e87830d..02af0d94e921 100644 --- a/Documentation/devicetree/bindings/hwmon/ina2xx.txt +++ b/Documentation/devicetree/bindings/hwmon/ina2xx.txt @@ -7,6 +7,7 @@ Required properties: - "ti,ina220" for ina220 - "ti,ina226" for ina226 - "ti,ina230" for ina230 + - "ti,ina231" for ina231 - reg: I2C address Optional properties: diff --git a/Documentation/devicetree/bindings/hwmon/jc42.txt b/Documentation/devicetree/bindings/hwmon/jc42.txt new file mode 100644 index 000000000000..07a250498fbb --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/jc42.txt @@ -0,0 +1,42 @@ +Properties for Jedec JC-42.4 compatible temperature sensors + +Required properties: +- compatible: May include a device-specific string consisting of the + manufacturer and the name of the chip. A list of supported + chip names follows. + Must include "jedec,jc-42.4-temp" for any Jedec JC-42.4 + compatible temperature sensor. + + Supported chip names: + adi,adt7408 + atmel,at30ts00 + atmel,at30tse004 + onnn,cat6095 + onnn,cat34ts02 + maxim,max6604 + microchip,mcp9804 + microchip,mcp9805 + microchip,mcp9808 + microchip,mcp98243 + microchip,mcp98244 + microchip,mcp9843 + nxp,se97 + nxp,se98 + st,stts2002 + st,stts2004 + st,stts3000 + st,stts424 + st,stts424e + idt,tse2002 + idt,tse2004 + idt,ts3000 + idt,ts3001 + +- reg: I2C address + +Example: + +temp-sensor@1a { + compatible = "jedec,jc-42.4-temp"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt index bfeabb843941..71191ff0e781 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt @@ -44,8 +44,8 @@ Required properties: - our-claim-gpio: The GPIO that we use to claim the bus. - their-claim-gpios: The GPIOs that the other sides use to claim the bus. Note that some implementations may only support a single other master. -- Standard I2C mux properties. See mux.txt in this directory. -- Single I2C child bus node at reg 0. See mux.txt in this directory. +- Standard I2C mux properties. See i2c-mux.txt in this directory. +- Single I2C child bus node at reg 0. See i2c-mux.txt in this directory. Optional properties: - slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us. diff --git a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt index 6078aefe7ed4..7ce23ac61308 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt @@ -27,7 +27,8 @@ Required properties: - i2c-bus-name: The name of this bus. Also needed as pinctrl-name for the I2C parents. -Furthermore, I2C mux properties and child nodes. See mux.txt in this directory. +Furthermore, I2C mux properties and child nodes. See i2c-mux.txt in this +directory. Example: diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt index 66709a825541..21da3ecbb370 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt @@ -22,8 +22,8 @@ Required properties: - i2c-parent: The phandle of the I2C bus that this multiplexer's master-side port is connected to. - mux-gpios: list of gpios used to control the muxer -* Standard I2C mux properties. See mux.txt in this directory. -* I2C child bus nodes. See mux.txt in this directory. +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. Optional properties: - idle-state: value to set the muxer to when idle. When no value is @@ -33,7 +33,7 @@ For each i2c child node, an I2C child bus will be created. They will be numbered based on their order in the device tree. Whenever an access is made to a device on a child bus, the value set -in the revelant node's reg property will be output using the list of +in the relevant node's reg property will be output using the list of GPIOs, the first in the list holding the least-significant value. If an idle state is defined, using the idle-state (optional) property, diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt index ae8af1694e95..33119a98e144 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt @@ -28,9 +28,9 @@ Also required are: * Standard pinctrl properties that specify the pin mux state for each child bus. See ../pinctrl/pinctrl-bindings.txt. -* Standard I2C mux properties. See mux.txt in this directory. +* Standard I2C mux properties. See i2c-mux.txt in this directory. -* I2C child bus nodes. See mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. For each named state defined in the pinctrl-names property, an I2C child bus will be created. I2C child bus numbers are assigned based on the index into diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt index 688783fbe696..de00d7fc450b 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt @@ -7,8 +7,8 @@ Required properties: - compatible: i2c-mux-reg - i2c-parent: The phandle of the I2C bus that this multiplexer's master-side port is connected to. -* Standard I2C mux properties. See mux.txt in this directory. -* I2C child bus nodes. See mux.txt in this directory. +* Standard I2C mux properties. See i2c-mux.txt in this directory. +* I2C child bus nodes. See i2c-mux.txt in this directory. Optional properties: - reg: this pair of <offset size> specifies the register to control the mux. @@ -24,7 +24,7 @@ Optional properties: given, it defaults to the last value used. Whenever an access is made to a device on a child bus, the value set -in the revelant node's reg property will be output to the register. +in the relevant node's reg property will be output to the register. If an idle state is defined, using the idle-state (optional) property, whenever an access is not being made to a device on a child bus, the diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 539874490492..acc5cd64711c 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -56,6 +56,70 @@ maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface mc,rv3029c2 Real Time Clock Module with I2C-Bus +microchip,mcp4531-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4531-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4531-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4531-104 Microchip 7-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4532-502 Microchip 7-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4532-103 Microchip 7-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4532-503 Microchip 7-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4532-104 Microchip 7-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4541-502 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4541-103 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4541-503 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4541-104 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4542-502 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4542-103 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4542-503 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4542-104 Microchip 7-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4551-502 Microchip 8-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4551-103 Microchip 8-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4551-503 Microchip 8-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4551-104 Microchip 8-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4552-502 Microchip 8-bit Single I2C Digital Potentiometer (5k) +microchip,mcp4552-103 Microchip 8-bit Single I2C Digital Potentiometer (10k) +microchip,mcp4552-503 Microchip 8-bit Single I2C Digital Potentiometer (50k) +microchip,mcp4552-104 Microchip 8-bit Single I2C Digital Potentiometer (100k) +microchip,mcp4561-502 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4561-103 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4561-503 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4561-104 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4562-502 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4562-103 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4562-503 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4562-104 Microchip 8-bit Single I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4631-502 Microchip 7-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4631-103 Microchip 7-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4631-503 Microchip 7-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4631-104 Microchip 7-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4632-502 Microchip 7-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4632-103 Microchip 7-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4632-503 Microchip 7-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4632-104 Microchip 7-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4641-502 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4641-103 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4641-503 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4641-104 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4642-502 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4642-103 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4642-503 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4642-104 Microchip 7-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4651-502 Microchip 8-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4651-103 Microchip 8-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4651-503 Microchip 8-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4651-104 Microchip 8-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4652-502 Microchip 8-bit Dual I2C Digital Potentiometer (5k) +microchip,mcp4652-103 Microchip 8-bit Dual I2C Digital Potentiometer (10k) +microchip,mcp4652-503 Microchip 8-bit Dual I2C Digital Potentiometer (50k) +microchip,mcp4652-104 Microchip 8-bit Dual I2C Digital Potentiometer (100k) +microchip,mcp4661-502 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4661-103 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4661-503 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4661-104 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) +microchip,mcp4662-502 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (5k) +microchip,mcp4662-103 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (10k) +microchip,mcp4662-503 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (50k) +microchip,mcp4662-104 Microchip 8-bit Dual I2C Digital Potentiometer with NV Memory (100k) national,lm63 Temperature sensor with integrated fan control national,lm75 I2C TEMP SENSOR national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor diff --git a/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt new file mode 100644 index 000000000000..caaaed765ce4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/brcm,iproc-static-adc.txt @@ -0,0 +1,41 @@ +* Broadcom's IPROC Static ADC controller + +Broadcom iProc ADC controller has 8 channels 10bit ADC. +Allows user to convert analog input voltage values to digital. + +Required properties: + +- compatible: Must be "brcm,iproc-static-adc" + +- adc-syscon: Handler of syscon node defining physical base address of the + controller and length of memory mapped region. + +- #io-channel-cells = <1>; As ADC has multiple outputs + refer to Documentation/devicetree/bindings/iio/iio-bindings.txt for details. + +- io-channel-ranges: + refer to Documentation/devicetree/bindings/iio/iio-bindings.txt for details. + +- clocks: Clock used for this block. + +- clock-names: Clock name should be given as tsc_clk. + +- interrupts: interrupt line number. + +For example: + + ts_adc_syscon: ts_adc_syscon@180a6000 { + compatible = "brcm,iproc-ts-adc-syscon","syscon"; + reg = <0x180a6000 0xc30>; + }; + + adc: adc@180a6000 { + compatible = "brcm,iproc-static-adc"; + adc-syscon = <&ts_adc_syscon>; + #io-channel-cells = <1>; + io-channel-ranges; + clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>; + clock-names = "tsc_clk"; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/max1363.txt b/Documentation/devicetree/bindings/iio/adc/max1363.txt new file mode 100644 index 000000000000..94a9011dd860 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/max1363.txt @@ -0,0 +1,63 @@ +* Maxim 1x3x/136x/116xx Analog to Digital Converter (ADC) + +The node for this driver must be a child node of a I2C controller, hence +all mandatory properties for your controller must be specified. See directory: + + Documentation/devicetree/bindings/i2c + +for more details. + +Required properties: + - compatible: Should be one of + "maxim,max1361" + "maxim,max1362" + "maxim,max1363" + "maxim,max1364" + "maxim,max1036" + "maxim,max1037" + "maxim,max1038" + "maxim,max1039" + "maxim,max1136" + "maxim,max1137" + "maxim,max1138" + "maxim,max1139" + "maxim,max1236" + "maxim,max1237" + "maxim,max1238" + "maxim,max1239" + "maxim,max11600" + "maxim,max11601" + "maxim,max11602" + "maxim,max11603" + "maxim,max11604" + "maxim,max11605" + "maxim,max11606" + "maxim,max11607" + "maxim,max11608" + "maxim,max11609" + "maxim,max11610" + "maxim,max11611" + "maxim,max11612" + "maxim,max11613" + "maxim,max11614" + "maxim,max11615" + "maxim,max11616" + "maxim,max11617" + "maxim,max11644" + "maxim,max11645" + "maxim,max11646" + "maxim,max11647" + - reg: Should contain the ADC I2C address + +Optional properties: + - vcc-supply: phandle to the regulator that provides power to the ADC. + - vref-supply: phandle to the regulator for ADC reference voltage. + - interrupts: IRQ line for the ADC. If not used the driver will use + polling. + +Example: +adc: max11644@36 { + compatible = "maxim,max11644"; + reg = <0x36>; + vref-supply = <&adc_vref>; +}; diff --git a/Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt b/Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt new file mode 100644 index 000000000000..2962bd9a2b3d --- /dev/null +++ b/Documentation/devicetree/bindings/iio/chemical/atlas,ec-sm.txt @@ -0,0 +1,22 @@ +* Atlas Scientific EC-SM OEM sensor + +http://www.atlas-scientific.com/_files/_datasheets/_oem/EC_oem_datasheet.pdf + +Required properties: + + - compatible: must be "atlas,ec-sm" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +atlas@64 { + compatible = "atlas,ec-sm"; + reg = <0x64>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; diff --git a/Documentation/devicetree/bindings/iio/dac/ad5755.txt b/Documentation/devicetree/bindings/iio/dac/ad5755.txt new file mode 100644 index 000000000000..f0bbd7e1029b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ad5755.txt @@ -0,0 +1,124 @@ +* Analog Device AD5755 IIO Multi-Channel DAC Linux Driver + +Required properties: + - compatible: Has to contain one of the following: + adi,ad5755 + adi,ad5755-1 + adi,ad5757 + adi,ad5735 + adi,ad5737 + + - reg: spi chip select number for the device + - spi-cpha or spi-cpol: is the only modes that is supported + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +See include/dt-bindings/iio/ad5755.h + - adi,ext-dc-dc-compenstation-resistor: boolean set if the hardware have an + external resistor and thereby bypasses + the internal compensation resistor. + - adi,dc-dc-phase: + Valid values for DC DC Phase control is: + 0: All dc-to-dc converters clock on the same edge. + 1: Channel A and Channel B clock on the same edge, + Channel C and Channel D clock on opposite edges. + 2: Channel A and Channel C clock on the same edge, + Channel B and Channel D clock on opposite edges. + 3: Channel A, Channel B, Channel C, and Channel D + clock 90 degrees out of phase from each other. + - adi,dc-dc-freq-hz: + Valid values for DC DC frequency is [Hz]: + 250000 + 410000 + 650000 + - adi,dc-dc-max-microvolt: + Valid values for the maximum allowed Vboost voltage supplied by + the dc-to-dc converter is: + 23000000 + 24500000 + 27000000 + 29500000 + +Optional for every channel: + - adi,mode: + Valid values for DAC modes is: + 0: 0 V to 5 V voltage range. + 1: 0 V to 10 V voltage range. + 2: Plus minus 5 V voltage range. + 3: Plus minus 10 V voltage range. + 4: 4 mA to 20 mA current range. + 5: 0 mA to 20 mA current range. + 6: 0 mA to 24 mA current range. + - adi,ext-current-sense-resistor: boolean set if the hardware a external + current sense resistor. + - adi,enable-voltage-overrange: boolean enable voltage overrange + - adi,slew: Array of slewrate settings should contain 3 fields: + 1: Should be either 0 or 1 in order to enable or disable slewrate. + 2: Slew rate settings: + Valid values for the slew rate update frequency: + 64000 + 32000 + 16000 + 8000 + 4000 + 2000 + 1000 + 500 + 250 + 125 + 64 + 32 + 16 + 8 + 4 + 0 + 3: Slew step size: + Valid values for the step size LSBs: + 1 + 2 + 4 + 16 + 32 + 64 + 128 + 256 + +Example: +dac@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "adi,ad5755"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpha; + adi,dc-dc-phase = <0>; + adi,dc-dc-freq-hz = <410000>; + adi,dc-dc-max-microvolt = <23000000>; + channel@0 { + reg = <0>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; + channel@1 { + reg = <1>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; + channel@2 { + reg = <2>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; + channel@3 { + reg = <3>; + adi,mode = <4>; + adi,ext-current-sense-resistor; + adi,slew = <0 64000 1>; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt index d7a6deb6b21e..c7198a03c906 100644 --- a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt +++ b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt @@ -1,7 +1,11 @@ -BMP085/BMP18x digital pressure sensors +BMP085/BMP18x/BMP28x digital pressure sensors Required properties: -- compatible: bosch,bmp085 +- compatible: must be one of: + "bosch,bmp085" + "bosch,bmp180" + "bosch,bmp280" + "bosch,bme280" Optional properties: - chip-id: configurable chip id for non-default chip revisions @@ -10,6 +14,10 @@ Optional properties: value range is 0-3 with rising sensitivity. - interrupt-parent: should be the phandle for the interrupt controller - interrupts: interrupt mapping for IRQ +- reset-gpios: a GPIO line handling reset of the sensor: as the line is + active low, it should be marked GPIO_ACTIVE_LOW (see gpio/gpio.txt) +- vddd-supply: digital voltage regulator (see regulator/regulator.txt) +- vdda-supply: analog voltage regulator (see regulator/regulator.txt) Example: @@ -21,4 +29,7 @@ pressure@77 { default-oversampling = <2>; interrupt-parent = <&gpio0>; interrupts = <25 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + vddd-supply = <&foo>; + vdda-supply = <&bar>; }; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index 5844cf72862d..e41fe340162b 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -64,3 +64,4 @@ Pressure sensors: - st,lps001wp-press - st,lps25h-press - st,lps331ap-press +- st,lps22hb-press diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt index 793c20ff8fcc..5393e2a45a42 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt @@ -21,6 +21,7 @@ Main node required properties: "arm,pl390" "arm,tc11mp-gic" "brcm,brahma-b15-gic" + "nvidia,tegra210-agic" "qcom,msm-8660-qgic" "qcom,msm-qgic2" - interrupt-controller : Identifies the node as an interrupt controller @@ -68,7 +69,7 @@ Optional "ic_clk" (for "arm,arm11mp-gic") "PERIPHCLKEN" (for "arm,cortex-a15-gic") "PERIPHCLK", "PERIPHCLKEN" (for "arm,cortex-a9-gic") - "clk" (for "arm,gic-400") + "clk" (for "arm,gic-400" and "nvidia,tegra210") "gclk" (for "arm,pl390") - power-domains : A phandle and PM domain specifier as defined by bindings of diff --git a/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt new file mode 100644 index 000000000000..6c6e85324b9d --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/aspeed,ast2400-vic.txt @@ -0,0 +1,22 @@ +Aspeed Vectored Interrupt Controller + +These bindings are for the Aspeed AST2400 interrupt controller register layout. +The SoC has an legacy register layout, but this driver does not support that +mode of operation. + +Required properties: + +- compatible : should be "aspeed,ast2400-vic". + +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 1. + +Example: + + vic: interrupt-controller@1e6c0080 { + compatible = "aspeed,ast2400-vic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x1e6c0080 0x80>; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt new file mode 100644 index 000000000000..59a47a5b924b --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -0,0 +1,59 @@ +Mediatek Video Codec + +Mediatek Video Codec is the video codec hw present in Mediatek SoCs which +supports high resolution encoding functionalities. + +Required properties: +- compatible : "mediatek,mt8173-vcodec-enc" for encoder +- reg : Physical base address of the video codec registers and length of + memory mapped region. +- interrupts : interrupt number to the cpu. +- mediatek,larb : must contain the local arbiters in the current Socs. +- clocks : list of clock specifiers, corresponding to entries in + the clock-names property. +- clock-names: encoder must contain "venc_sel_src", "venc_sel", +- "venc_lt_sel_src", "venc_lt_sel". +- iommus : should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. +- mediatek,vpu : the node of video processor unit + +Example: +vcodec_enc: vcodec@0x18002000 { + compatible = "mediatek,mt8173-vcodec-enc"; + reg = <0 0x18002000 0 0x1000>, /*VENC_SYS*/ + <0 0x19002000 0 0x1000>; /*VENC_LT_SYS*/ + interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 202 IRQ_TYPE_LEVEL_LOW>; + mediatek,larb = <&larb3>, + <&larb5>; + iommus = <&iommu M4U_PORT_VENC_RCPU>, + <&iommu M4U_PORT_VENC_REC>, + <&iommu M4U_PORT_VENC_BSDMA>, + <&iommu M4U_PORT_VENC_SV_COMV>, + <&iommu M4U_PORT_VENC_RD_COMV>, + <&iommu M4U_PORT_VENC_CUR_LUMA>, + <&iommu M4U_PORT_VENC_CUR_CHROMA>, + <&iommu M4U_PORT_VENC_REF_LUMA>, + <&iommu M4U_PORT_VENC_REF_CHROMA>, + <&iommu M4U_PORT_VENC_NBM_RDMA>, + <&iommu M4U_PORT_VENC_NBM_WDMA>, + <&iommu M4U_PORT_VENC_RCPU_SET2>, + <&iommu M4U_PORT_VENC_REC_FRM_SET2>, + <&iommu M4U_PORT_VENC_BSDMA_SET2>, + <&iommu M4U_PORT_VENC_SV_COMA_SET2>, + <&iommu M4U_PORT_VENC_RD_COMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_LUMA_SET2>, + <&iommu M4U_PORT_VENC_CUR_CHROMA_SET2>, + <&iommu M4U_PORT_VENC_REF_LUMA_SET2>, + <&iommu M4U_PORT_VENC_REC_CHROMA_SET2>; + mediatek,vpu = <&vpu>; + clocks = <&topckgen CLK_TOP_VENCPLL_D2>, + <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_UNIVPLL1_D2>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + clock-names = "venc_sel_src", + "venc_sel", + "venc_lt_sel_src", + "venc_lt_sel"; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vpu.txt b/Documentation/devicetree/bindings/media/mediatek-vpu.txt new file mode 100644 index 000000000000..2a5bac37f9a2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/mediatek-vpu.txt @@ -0,0 +1,31 @@ +* Mediatek Video Processor Unit + +Video Processor Unit is a HW video controller. It controls HW Codec including +H.264/VP8/VP9 Decode, H.264/VP8 Encode and Image Processor (scale/rotate/color convert). + +Required properties: + - compatible: "mediatek,mt8173-vpu" + - reg: Must contain an entry for each entry in reg-names. + - reg-names: Must include the following entries: + "tcm": tcm base + "cfg_reg": Main configuration registers base + - interrupts: interrupt number to the cpu. + - clocks : clock name from clock manager + - clock-names: must be main. It is the main clock of VPU + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for VPU extended memory; if not present, VPU may be located + anywhere in the memory + +Example: + vpu: vpu@10020000 { + compatible = "mediatek,mt8173-vpu"; + reg = <0 0x10020000 0 0x30000>, + <0 0x10050000 0 0x100>; + reg-names = "tcm", "cfg_reg"; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen TOP_SCP_SEL>; + clock-names = "main"; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt new file mode 100644 index 000000000000..6a12960609d8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt @@ -0,0 +1,32 @@ +Renesas R-Car Frame Compression Processor (FCP) +----------------------------------------------- + +The FCP is a companion module of video processing modules in the Renesas R-Car +Gen3 SoCs. It provides data compression and decompression, data caching, and +conversion of AXI transactions in order to reduce the memory bandwidth. + +There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and FCP +for FDP (FCPF). Their configuration and behaviour depend on the module they +are paired with. These DT bindings currently support the FCPV only. + + - compatible: Must be one or more of the following + + - "renesas,r8a7795-fcpv" for R8A7795 (R-Car H3) compatible 'FCP for VSP' + - "renesas,fcpv" for generic compatible 'FCP for VSP' + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first, followed by the + family-specific and/or generic versions. + + - reg: the register base and size for the device registers + - clocks: Reference to the functional clock + + +Device node example +------------------- + + fcpvd1: fcp@fea2f000 { + compatible = "renesas,r8a7795-fcpv", "renesas,fcpv"; + reg = <0 0xfea2f000 0 0x200>; + clocks = <&cpg CPG_MOD 602>; + }; diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 627405abd144..9b695bcbf219 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -14,6 +14,11 @@ Required properties: - interrupts: VSP interrupt specifier. - clocks: A phandle + clock-specifier pair for the VSP functional clock. +Optional properties: + + - renesas,fcp: A phandle referencing the FCP that handles memory accesses + for the VSP. Not needed on Gen2, mandatory on Gen3. + Example: R8A7790 (R-Car H2) VSP1-S node diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt new file mode 100644 index 000000000000..925ab4d72eaa --- /dev/null +++ b/Documentation/devicetree/bindings/media/s5p-cec.txt @@ -0,0 +1,31 @@ +* Samsung HDMI CEC driver + +The HDMI CEC module is present is Samsung SoCs and its purpose is to +handle communication between HDMI connected devices over the CEC bus. + +Required properties: + - compatible : value should be following + "samsung,s5p-cec" + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : HDMI CEC interrupt number to the CPU. + - clocks : from common clock binding: handle to HDMI CEC clock. + - clock-names : from common clock binding: must contain "hdmicec", + corresponding to entry in the clocks property. + - samsung,syscon-phandle - phandle to the PMU system controller + +Example: + +hdmicec: cec@100B0000 { + compatible = "samsung,s5p-cec"; + reg = <0x100B0000 0x200>; + interrupts = <0 114 0>; + clocks = <&clock CLK_HDMI_CEC>; + clock-names = "hdmicec"; + samsung,syscon-phandle = <&pmu_system_controller>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_cec>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt index 2d5787eac91a..92c94f5ecbf1 100644 --- a/Documentation/devicetree/bindings/media/s5p-mfc.txt +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -21,15 +21,18 @@ Required properties: - clock-names : from common clock binding: must contain "mfc", corresponding to entry in the clocks property. - - samsung,mfc-r : Base address of the first memory bank used by MFC - for DMA contiguous memory allocation and its size. - - - samsung,mfc-l : Base address of the second memory bank used by MFC - for DMA contiguous memory allocation and its size. - Optional properties: - power-domains : power-domain property defined with a phandle to respective power domain. + - memory-region : from reserved memory binding: phandles to two reserved + memory regions, first is for "left" mfc memory bus interfaces, + second if for the "right" mfc memory bus, used when no SYSMMU + support is available + +Obsolete properties: + - samsung,mfc-r, samsung,mfc-l : support removed, please use memory-region + property instead + Example: SoC specific DT entry: @@ -43,9 +46,29 @@ mfc: codec@13400000 { clock-names = "mfc"; }; +Reserved memory specific DT entry for given board (see reserved memory binding +for more information): + +reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mfc_left: region@51000000 { + compatible = "shared-dma-pool"; + no-map; + reg = <0x51000000 0x800000>; + }; + + mfc_right: region@43000000 { + compatible = "shared-dma-pool"; + no-map; + reg = <0x43000000 0x800000>; + }; +}; + Board specific DT entry: codec@13400000 { - samsung,mfc-r = <0x43000000 0x800000>; - samsung,mfc-l = <0x51000000 0x800000>; + memory-region = <&mfc_left>, <&mfc_right>; }; diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index d20b1034e967..585a95546288 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -22,6 +22,11 @@ Optional properties: AXP152/20X: range: 750-1875, Default: 1.5 MHz AXP22X/80X: range: 1800-4050, Default: 3 MHz +- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the + N_VBUSEN pin is used as an output pin to control an external + regulator to drive the OTG VBus, rather then as an input pin + which signals whether the board is driving OTG VBus or not. + - <input>-supply: a phandle to the regulator supply node. May be omitted if inputs are unregulated, such as using the IPSOUT output from the PMIC. @@ -79,6 +84,7 @@ ELDO3 : LDO : eldoin-supply : shared supply LDO_IO0 : LDO : ips-supply : GPIO 0 LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on +DRIVEVBUS : Enable output : drivevbus-supply : external regulator AXP809 regulators, type, and corresponding input supply names: diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt index 937785a3eddc..9e6770b105c9 100644 --- a/Documentation/devicetree/bindings/mfd/rn5t618.txt +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -1,18 +1,21 @@ -* Ricoh RN5T618 PMIC +* Ricoh RN5T567/RN5T618 PMIC -Ricoh RN5T618 is a power management IC which integrates 3 step-down -DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, -fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled -through a I2C interface. +Ricoh RN5T567/RN5T618 is a power management IC family which integrates +3 to 4 step-down DCDC converters, 7 low-dropout regulators, GPIOs and +a watchdog timer. The RN5T618 provides additionally a Li-ion battery +charger, fuel gauge and an ADC. It can be controlled through an I2C +interface. Required properties: - - compatible: should be "ricoh,rn5t618" + - compatible: must be one of + "ricoh,rn5t567" + "ricoh,rn5t618" - reg: the I2C slave address of the device Sub-nodes: - regulators: the node is required if the regulator functionality is - needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, - LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4 + (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. The common bindings for each individual regulator can be found in: Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/misc/ramoops.txt b/Documentation/devicetree/bindings/misc/ramoops.txt new file mode 100644 index 000000000000..cd02cec67d38 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/ramoops.txt @@ -0,0 +1,48 @@ +Ramoops oops/panic logger +========================= + +ramoops provides persistent RAM storage for oops and panics, so they can be +recovered after a reboot. It is a backend to pstore, so this node is named +"ramoops" after the backend, rather than "pstore" which is the subsystem. + +Parts of this storage may be set aside for other persistent log buffers, such +as kernel log messages, or for optional ECC error-correction data. The total +size of these optional buffers must fit in the reserved region. + +Any remaining space will be used for a circular buffer of oops and panic +records. These records have a configurable size, with a size of 0 indicating +that they should be disabled. + +At least one of "record-size", "console-size", "ftrace-size", or "pmsg-size" +must be set non-zero, but are otherwise optional as listed below. + + +Required properties: + +- compatible: must be "ramoops" + +- memory-region: phandle to a region of memory that is preserved between + reboots + + +Optional properties: + +- ecc-size: enables ECC support and specifies ECC buffer size in bytes + (defaults to 0: no ECC) + +- record-size: maximum size in bytes of each dump done on oops/panic + (defaults to 0: disabled) + +- console-size: size in bytes of log buffer reserved for kernel messages + (defaults to 0: disabled) + +- ftrace-size: size in bytes of log buffer reserved for function tracing and + profiling (defaults to 0: disabled) + +- pmsg-size: size in bytes of log buffer reserved for userspace messages + (defaults to 0: disabled) + +- unbuffered: if present, use unbuffered mappings to map the reserved region + (defaults to buffered mappings) + +- no-dump-oops: if present, only dump panics (defaults to panics and oops) diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt index 14aa6cf58201..6a9a63cb0543 100644 --- a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt +++ b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt @@ -13,10 +13,10 @@ Optional properties: initialization. This is an array of 28 values(u8). - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip. - firmware will use the pin to wakeup host system. + firmware will use the pin to wakeup host system (u16). - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host platform. The value will be configured to firmware. This - is needed to work chip's sleep feature as expected. + is needed to work chip's sleep feature as expected (u16). - interrupt-parent: phandle of the parent interrupt controller - interrupts : interrupt pin number to the cpu. Driver will request an irq based on this interrupt number. During system suspend, the irq will be @@ -50,7 +50,7 @@ calibration data is also available in below example. 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xf0 0x00>; - marvell,wakeup-pin = <0x0d>; - marvell,wakeup-gap-ms = <0x64>; + marvell,wakeup-pin = /bits/ 16 <0x0d>; + marvell,wakeup-gap-ms = /bits/ 16 <0x64>; }; }; diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index d0231209d846..6ccce09d8bbf 100644 --- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -5,6 +5,7 @@ Required properties: "brcm,bcm7425-sata-phy" "brcm,bcm7445-sata-phy" "brcm,iproc-ns2-sata-phy" + "brcm,iproc-nsp-sata-phy" "brcm,phy-sata3" - address-cells: should be 1 - size-cells: should be 0 @@ -22,7 +23,8 @@ Sub-nodes required properties: Sub-nodes optional properties: - brcm,enable-ssc: use spread spectrum clocking (SSC) on this port - This property is not applicable for "brcm,iproc-ns2-sata-phy". + This property is not applicable for "brcm,iproc-ns2-sata-phy" and + "brcm,iproc-nsp-sata-phy". Example: sata-phy@f0458100 { diff --git a/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt new file mode 100644 index 000000000000..c26478be391b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt @@ -0,0 +1,40 @@ +TI DA8xx/OMAP-L1xx/AM18xx USB PHY + +Required properties: + - compatible: must be "ti,da830-usb-phy". + - #phy-cells: must be 1. + +This device controls the PHY for both the USB 1.1 OHCI and USB 2.0 OTG +controllers on DA8xx SoCs. Consumers of this device should use index 0 for +the USB 2.0 phy device and index 1 for the USB 1.1 phy device. + +It also requires a "syscon" node with compatible = "ti,da830-cfgchip", "syscon" +to access the CFGCHIP2 register. + +Example: + + cfgchip: cfgchip@1417c { + compatible = "ti,da830-cfgchip", "syscon"; + reg = <0x1417c 0x14>; + }; + + usb_phy: usb-phy { + compatible = "ti,da830-usb-phy"; + #phy-cells = <1>; + }; + + usb20: usb@200000 { + compatible = "ti,da830-musb"; + reg = <0x200000 0x1000>; + interrupts = <58>; + phys = <&usb_phy 0>; + phy-names = "usb-phy"; + }; + + usb11: usb@225000 { + compatible = "ti,da830-ohci"; + reg = <0x225000 0x1000>; + interrupts = <59>; + phys = <&usb_phy 1>; + phy-names = "usb-phy"; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt index 68498d560354..cc6be9680a6d 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt @@ -5,11 +5,13 @@ Required properties: "rockchip,rk3066a-usb-phy" "rockchip,rk3188-usb-phy" "rockchip,rk3288-usb-phy" - - rockchip,grf : phandle to the syscon managing the "general - register files" - #address-cells: should be 1 - #size-cells: should be 0 +Deprecated properties: + - rockchip,grf : phandle to the syscon managing the "general + register files" - phy should be a child of the GRF instead + Sub-nodes: Each PHY should be represented as a sub-node. @@ -28,14 +30,19 @@ Optional Properties: Example: -usbphy: phy { - compatible = "rockchip,rk3288-usb-phy"; - rockchip,grf = <&grf>; - #address-cells = <1>; - #size-cells = <0>; +grf: syscon@ff770000 { + compatible = "rockchip,rk3288-grf", "syscon", "simple-mfd"; + +... + + usbphy: phy { + compatible = "rockchip,rk3288-usb-phy"; + #address-cells = <1>; + #size-cells = <0>; - usbphy0: usb-phy0 { - #phy-cells = <0>; - reg = <0x320>; + usbphy0: usb-phy0 { + #phy-cells = <0>; + reg = <0x320>; + }; }; }; diff --git a/Documentation/devicetree/bindings/regulator/da9210.txt b/Documentation/devicetree/bindings/regulator/da9210.txt index 7aa9b1fa6b21..58065ca9e3b4 100644 --- a/Documentation/devicetree/bindings/regulator/da9210.txt +++ b/Documentation/devicetree/bindings/regulator/da9210.txt @@ -1,4 +1,4 @@ -* Dialog Semiconductor DA9210 Voltage Regulator +* Dialog Semiconductor DA9210 Multi-phase 12A DCDC BUCK Converter Required properties: @@ -18,8 +18,12 @@ Example: compatible = "dlg,da9210"; reg = <0x68>; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1000000>; + interrupt-parent = <...>; + interrupts = <...>; + + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <1600000>; + regulator-max-microamp = <4600000>; regulator-boot-on; - regulator-always-on; }; diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt index c620493e8dbe..0f2a6f8fcafd 100644 --- a/Documentation/devicetree/bindings/regulator/da9211.txt +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -1,7 +1,8 @@ -* Dialog Semiconductor DA9211/DA9213/DA9215 Voltage Regulator +* Dialog Semiconductor DA9211/DA9212/DA9213/DA9214/DA9215 Voltage Regulator Required properties: -- compatible: "dlg,da9211" or "dlg,da9213" or "dlg,da9215" +- compatible: "dlg,da9211" or "dlg,da9212" or "dlg,da9213" + or "dlg,da9214" or "dlg,da9215" - reg: I2C slave address, usually 0x68. - interrupts: the interrupt outputs of the controller - regulators: A node that houses a sub-node for each regulator within the @@ -30,6 +31,25 @@ Example 1) DA9211 regulator-max-microamp = <5000000>; enable-gpios = <&gpio 27 0>; }; + }; + }; + +Example 2) DA9212 + + pmic: da9212@68 { + compatible = "dlg,da9212"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <2000000>; + regulator-max-microamp = <5000000>; + enable-gpios = <&gpio 27 0>; + }; BUCKB { regulator-name = "VBUCKB"; regulator-min-microvolt = < 300000>; @@ -41,7 +61,7 @@ Example 1) DA9211 }; }; -Example 2) DA9213 +Example 3) DA9213 pmic: da9213@68 { compatible = "dlg,da9213"; reg = <0x68>; @@ -56,6 +76,24 @@ Example 2) DA9213 regulator-max-microamp = <6000000>; enable-gpios = <&gpio 27 0>; }; + }; + }; + +Example 4) DA9214 + pmic: da9214@68 { + compatible = "dlg,da9214"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <3000000>; + regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 27 0>; + }; BUCKB { regulator-name = "VBUCKB"; regulator-min-microvolt = < 300000>; @@ -67,8 +105,7 @@ Example 2) DA9213 }; }; - -Example 3) DA9215 +Example 5) DA9215 pmic: da9215@68 { compatible = "dlg,da9215"; reg = <0x68>; diff --git a/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt new file mode 100644 index 000000000000..c35d878b0960 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6323-regulator.txt @@ -0,0 +1,237 @@ +Mediatek MT6323 Regulator Driver + +All voltage regulators are defined as subnodes of the regulators node. A list +of regulators provided by this controller are defined as subnodes of the +PMIC's node. Each regulator is named according to its regulator type, +buck_<name> and ldo_<name>. The definition for each of these nodes is defined +using the standard binding for regulators at +Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are:: +BUCK: + buck_vproc, buck_vsys, buck_vpa +LDO: + ldo_vtcxo, ldo_vcn28, ldo_vcn33_bt, ldo_vcn33_wifi, ldo_va, ldo_vcama, + ldo_vio28, ldo_vusb, ldo_vmc, ldo_vmch, ldo_vemc3v3, ldo_vgp1, ldo_vgp2, + ldo_vgp3, ldo_vcn18, ldo_vsim1, ldo_vsim2, ldo_vrtc, ldo_vcamaf, ldo_vibr, + ldo_vrf18, ldo_vm, ldo_vio18, ldo_vcamd, ldo_vcamio + +Example: + + pmic: mt6323 { + mt6323regulator: regulators { + mt6323_vproc_reg: buck_vproc{ + regulator-name = "vproc"; + regulator-min-microvolt = < 700000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vsys_reg: buck_vsys{ + regulator-name = "vsys"; + regulator-min-microvolt = <1400000>; + regulator-max-microvolt = <2987500>; + regulator-ramp-delay = <25000>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vpa_reg: buck_vpa{ + regulator-name = "vpa"; + regulator-min-microvolt = < 500000>; + regulator-max-microvolt = <3650000>; + }; + + mt6323_vtcxo_reg: ldo_vtcxo{ + regulator-name = "vtcxo"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <90>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcn28_reg: ldo_vcn28{ + regulator-name = "vcn28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <185>; + }; + + mt6323_vcn33_bt_reg: ldo_vcn33_bt{ + regulator-name = "vcn33_bt"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3600000>; + regulator-enable-ramp-delay = <185>; + }; + + mt6323_vcn33_wifi_reg: ldo_vcn33_wifi{ + regulator-name = "vcn33_wifi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3600000>; + regulator-enable-ramp-delay = <185>; + }; + + mt6323_va_reg: ldo_va{ + regulator-name = "va"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcama_reg: ldo_vcama{ + regulator-name = "vcama"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vio28_reg: ldo_vio28{ + regulator-name = "vio28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vusb_reg: ldo_vusb{ + regulator-name = "vusb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + regulator-boot-on; + }; + + mt6323_vmc_reg: ldo_vmc{ + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + mt6323_vmch_reg: ldo_vmch{ + regulator-name = "vmch"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + mt6323_vemc3v3_reg: ldo_vemc3v3{ + regulator-name = "vemc3v3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + regulator-boot-on; + }; + + mt6323_vgp1_reg: ldo_vgp1{ + regulator-name = "vgp1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vgp2_reg: ldo_vgp2{ + regulator-name = "vgp2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vgp3_reg: ldo_vgp3{ + regulator-name = "vgp3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vcn18_reg: ldo_vcn18{ + regulator-name = "vcn18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vsim1_reg: ldo_vsim1{ + regulator-name = "vsim1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vsim2_reg: ldo_vsim2{ + regulator-name = "vsim2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vrtc_reg: ldo_vrtc{ + regulator-name = "vrtc"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcamaf_reg: ldo_vcamaf{ + regulator-name = "vcamaf"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vibr_reg: ldo_vibr{ + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <36>; + }; + + mt6323_vrf18_reg: ldo_vrf18{ + regulator-name = "vrf18"; + regulator-min-microvolt = <1825000>; + regulator-max-microvolt = <1825000>; + regulator-enable-ramp-delay = <187>; + }; + + mt6323_vm_reg: ldo_vm{ + regulator-name = "vm"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vio18_reg: ldo_vio18{ + regulator-name = "vio18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + regulator-always-on; + regulator-boot-on; + }; + + mt6323_vcamd_reg: ldo_vcamd{ + regulator-name = "vcamd"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + + mt6323_vcamio_reg: ldo_vcamio{ + regulator-name = "vcamio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <216>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index ed936f0f34f2..dd6f59cf1455 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -38,13 +38,18 @@ NB: To be clear, if voltage-table is provided, then the device will be used in Voltage Table Mode. If no voltage-table is provided, then the device will be used in Continuous Voltage Mode. +Optional properties: +-------------------- +- enable-gpios: GPIO to use to enable/disable the regulator + Any property defined as part of the core regulator binding can also be used. (See: ../regulator/regulator.txt) -Continuous Voltage Example: +Continuous Voltage With Enable GPIO Example: pwm_regulator { compatible = "pwm-regulator; pwms = <&pwm1 0 8448 0>; + enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>; regulator-min-microvolt = <1016000>; regulator-max-microvolt = <1114000>; regulator-name = "vdd_logic"; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 46c6f3ed1a1c..0fa3b0fac129 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -113,9 +113,9 @@ pm8916: l14, l15, l16, l17, l18 pm8941: - s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, - l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, - mvs1, mvs2 + s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, + l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, + 5vs1, 5vs2 pm8994: s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, diff --git a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt index 07ccdaa68324..26542690b578 100644 --- a/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt +++ b/Documentation/devicetree/bindings/rng/brcm,bcm2835.txt @@ -2,7 +2,8 @@ BCM2835 Random number generator Required properties: -- compatible : should be "brcm,bcm2835-rng" +- compatible : should be "brcm,bcm2835-rng" or "brcm,bcm-nsp-rng" or + "brcm,bcm5301x-rng" - reg : Specifies base physical address and size of the registers. Example: @@ -11,3 +12,8 @@ rng { compatible = "brcm,bcm2835-rng"; reg = <0x7e104000 0x10>; }; + +rng@18033000 { + compatible = "brcm,bcm-nsp-rng"; + reg = <0x18033000 0x14>; +}; diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 936ab5b87324..f5561ac7e17e 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -42,6 +42,9 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. +- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD + line respectively. It will use specified GPIO instead of the peripheral + function pin for the UART feature. If unsure, don't specify this property. Note: * fsl,ns16550: @@ -63,3 +66,19 @@ Example: interrupts = <10>; reg-shift = <2>; }; + +Example for OMAP UART using GPIO-based modem control signals: + + uart4: serial@49042000 { + compatible = "ti,omap3-uart"; + reg = <0x49042000 0x400>; + interrupts = <80>; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; + dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 528c3b90f23c..1e4000d83aee 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -31,6 +31,8 @@ Required properties: - "renesas,hscif-r8a7794" for R8A7794 (R-Car E2) HSCIF compatible UART. - "renesas,scif-r8a7795" for R8A7795 (R-Car H3) SCIF compatible UART. - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. + - "renesas,scif-r8a7796" for R8A7796 (R-Car M3-W) SCIF compatible UART. + - "renesas,hscif-r8a7796" for R8A7796 (R-Car M3-W) HSCIF compatible UART. - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - "renesas,rcar-gen1-scif" for R-Car Gen1 SCIF compatible UART, @@ -76,6 +78,10 @@ Optional properties: - dmas: Must contain a list of two references to DMA specifiers, one for transmission, and one for reception. - dma-names: Must contain a list of two DMA names, "tx" and "rx". + - {cts,dsr,dcd,rng,rts,dtr}-gpios: Specify GPIOs for modem lines, cfr. the + generic serial DT bindings in serial.txt. + - uart-has-rtscts: Indicates dedicated lines for RTS/CTS hardware flow + control, cfr. the generic serial DT bindings in serial.txt. Example: aliases { diff --git a/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt b/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt new file mode 100644 index 000000000000..3ca89cd1caef --- /dev/null +++ b/Documentation/devicetree/bindings/timer/oxsemi,rps-timer.txt @@ -0,0 +1,17 @@ +Oxford Semiconductor OXNAS SoCs Family RPS Timer +================================================ + +Required properties: +- compatible: Should be "oxsemi,ox810se-rps-timer" +- reg : Specifies base physical address and size of the registers. +- interrupts : The interrupts of the two timers +- clocks : The phandle of the timer clock source + +example: + +timer0: timer@200 { + compatible = "oxsemi,ox810se-rps-timer"; + reg = <0x200 0x40>; + clocks = <&rpsclk>; + interrupts = <4 5>; +}; diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk3288-timer.txt b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.txt index 87f0b0042bae..a41b184d5538 100644 --- a/Documentation/devicetree/bindings/timer/rockchip,rk3288-timer.txt +++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.txt @@ -1,7 +1,9 @@ -Rockchip rk3288 timer +Rockchip rk timer Required properties: -- compatible: shall be "rockchip,rk3288-timer" +- compatible: shall be one of: + "rockchip,rk3288-timer" - for rk3066, rk3036, rk3188, rk322x, rk3288, rk3368 + "rockchip,rk3399-timer" - for rk3399 - reg: base address of the timer register starting with TIMERS CONTROL register - interrupts: should contain the interrupts for Timer0 - clocks : must contain an entry for each entry in clock-names diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 1084e2bcbe1c..341dc67f3472 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -93,7 +93,7 @@ Example: phys = <&usb_phy0>; phy-names = "usb-phy"; vbus-supply = <®_usb0_vbus>; - gadget-itc-setting = <0x4>; /* 4 micro-frames */ + itc-setting = <0x4>; /* 4 micro-frames */ /* Incremental burst of unspecified length */ ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index 19233b7365e1..9df456968596 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -14,7 +14,7 @@ Optional properties: - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" -- resets : phandle + reset specifier pair +- resets : a list of phandle + reset specifier pairs Example: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index a7440bcd67ff..2c2500df0dce 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -255,6 +255,7 @@ synology Synology, Inc. SUNW Sun Microsystems, Inc tbs TBS Technologies tcl Toby Churchill Ltd. +technexion TechNexion technologic Technologic Systems thine THine Electronics, Inc. ti Texas Instruments @@ -269,6 +270,7 @@ tronsmart Tronsmart truly Truly Semiconductors Limited tyan Tyan Computer Corporation upisemi uPI Semiconductor Corp. +uniwest United Western Technologies Corp (UniWest) urt United Radiant Technology Corporation usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor |