summaryrefslogtreecommitdiff
path: root/Documentation/gpio
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/gpio')
-rw-r--r--Documentation/gpio/00-INDEX2
-rw-r--r--Documentation/gpio/gpio.txt119
2 files changed, 0 insertions, 121 deletions
diff --git a/Documentation/gpio/00-INDEX b/Documentation/gpio/00-INDEX
index 179beb234f98..52fe0fa6c964 100644
--- a/Documentation/gpio/00-INDEX
+++ b/Documentation/gpio/00-INDEX
@@ -1,7 +1,5 @@
00-INDEX
- This file
-gpio.txt
- - Introduction to GPIOs and their kernel interfaces
consumer.txt
- How to obtain and use GPIOs in a driver
driver.txt
diff --git a/Documentation/gpio/gpio.txt b/Documentation/gpio/gpio.txt
deleted file mode 100644
index cd9b356e88cd..000000000000
--- a/Documentation/gpio/gpio.txt
+++ /dev/null
@@ -1,119 +0,0 @@
-GPIO Interfaces
-===============
-
-The documents in this directory give detailed instructions on how to access
-GPIOs in drivers, and how to write a driver for a device that provides GPIOs
-itself.
-
-Due to the history of GPIO interfaces in the kernel, there are two different
-ways to obtain and use GPIOs:
-
- - The descriptor-based interface is the preferred way to manipulate GPIOs,
-and is described by all the files in this directory excepted gpio-legacy.txt.
- - The legacy integer-based interface which is considered deprecated (but still
-usable for compatibility reasons) is documented in gpio-legacy.txt.
-
-The remainder of this document applies to the new descriptor-based interface.
-gpio-legacy.txt contains the same information applied to the legacy
-integer-based interface.
-
-
-What is a GPIO?
-===============
-
-A "General Purpose Input/Output" (GPIO) is a flexible software-controlled
-digital signal. They are provided from many kinds of chip, and are familiar
-to Linux developers working with embedded and custom hardware. Each GPIO
-represents a bit connected to a particular pin, or "ball" on Ball Grid Array
-(BGA) packages. Board schematics show which external hardware connects to
-which GPIOs. Drivers can be written generically, so that board setup code
-passes such pin configuration data to drivers.
-
-System-on-Chip (SOC) processors heavily rely on GPIOs. In some cases, every
-non-dedicated pin can be configured as a GPIO; and most chips have at least
-several dozen of them. Programmable logic devices (like FPGAs) can easily
-provide GPIOs; multifunction chips like power managers, and audio codecs
-often have a few such pins to help with pin scarcity on SOCs; and there are
-also "GPIO Expander" chips that connect using the I2C or SPI serial buses.
-Most PC southbridges have a few dozen GPIO-capable pins (with only the BIOS
-firmware knowing how they're used).
-
-The exact capabilities of GPIOs vary between systems. Common options:
-
- - Output values are writable (high=1, low=0). Some chips also have
- options about how that value is driven, so that for example only one
- value might be driven, supporting "wire-OR" and similar schemes for the
- other value (notably, "open drain" signaling).
-
- - Input values are likewise readable (1, 0). Some chips support readback
- of pins configured as "output", which is very useful in such "wire-OR"
- cases (to support bidirectional signaling). GPIO controllers may have
- input de-glitch/debounce logic, sometimes with software controls.
-
- - Inputs can often be used as IRQ signals, often edge triggered but
- sometimes level triggered. Such IRQs may be configurable as system
- wakeup events, to wake the system from a low power state.
-
- - Usually a GPIO will be configurable as either input or output, as needed
- by different product boards; single direction ones exist too.
-
- - Most GPIOs can be accessed while holding spinlocks, but those accessed
- through a serial bus normally can't. Some systems support both types.
-
-On a given board each GPIO is used for one specific purpose like monitoring
-MMC/SD card insertion/removal, detecting card write-protect status, driving
-a LED, configuring a transceiver, bit-banging a serial bus, poking a hardware
-watchdog, sensing a switch, and so on.
-
-
-Common GPIO Properties
-======================
-
-These properties are met through all the other documents of the GPIO interface
-and it is useful to understand them, especially if you need to define GPIO
-mappings.
-
-Active-High and Active-Low
---------------------------
-It is natural to assume that a GPIO is "active" when its output signal is 1
-("high"), and inactive when it is 0 ("low"). However in practice the signal of a
-GPIO may be inverted before is reaches its destination, or a device could decide
-to have different conventions about what "active" means. Such decisions should
-be transparent to device drivers, therefore it is possible to define a GPIO as
-being either active-high ("1" means "active", the default) or active-low ("0"
-means "active") so that drivers only need to worry about the logical signal and
-not about what happens at the line level.
-
-Open Drain and Open Source
---------------------------
-Sometimes shared signals need to use "open drain" (where only the low signal
-level is actually driven), or "open source" (where only the high signal level is
-driven) signaling. That term applies to CMOS transistors; "open collector" is
-used for TTL. A pullup or pulldown resistor causes the high or low signal level.
-This is sometimes called a "wire-AND"; or more practically, from the negative
-logic (low=true) perspective this is a "wire-OR".
-
-One common example of an open drain signal is a shared active-low IRQ line.
-Also, bidirectional data bus signals sometimes use open drain signals.
-
-Some GPIO controllers directly support open drain and open source outputs; many
-don't. When you need open drain signaling but your hardware doesn't directly
-support it, there's a common idiom you can use to emulate it with any GPIO pin
-that can be used as either an input or an output:
-
- LOW: gpiod_direction_output(gpio, 0) ... this drives the signal and overrides
- the pullup.
-
- HIGH: gpiod_direction_input(gpio) ... this turns off the output, so the pullup
- (or some other device) controls the signal.
-
-The same logic can be applied to emulate open source signaling, by driving the
-high signal and configuring the GPIO as input for low. This open drain/open
-source emulation can be handled transparently by the GPIO framework.
-
-If you are "driving" the signal high but gpiod_get_value(gpio) reports a low
-value (after the appropriate rise time passes), you know some other component is
-driving the shared signal low. That's not necessarily an error. As one common
-example, that's how I2C clocks are stretched: a slave that needs a slower clock
-delays the rising edge of SCK, and the I2C master adjusts its signaling rate
-accordingly.