summaryrefslogtreecommitdiff
path: root/Documentation/hwmon
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/hwmon')
-rw-r--r--Documentation/hwmon/ads10158
-rw-r--r--Documentation/hwmon/htu2146
-rw-r--r--Documentation/hwmon/k10temp1
3 files changed, 53 insertions, 2 deletions
diff --git a/Documentation/hwmon/ads1015 b/Documentation/hwmon/ads1015
index f6fe9c203733..063b80d857b1 100644
--- a/Documentation/hwmon/ads1015
+++ b/Documentation/hwmon/ads1015
@@ -6,6 +6,10 @@ Supported chips:
Prefix: 'ads1015'
Datasheet: Publicly available at the Texas Instruments website :
http://focus.ti.com/lit/ds/symlink/ads1015.pdf
+ * Texas Instruments ADS1115
+ Prefix: 'ads1115'
+ Datasheet: Publicly available at the Texas Instruments website :
+ http://focus.ti.com/lit/ds/symlink/ads1115.pdf
Authors:
Dirk Eibach, Guntermann & Drunck GmbH <eibach@gdsys.de>
@@ -13,9 +17,9 @@ Authors:
Description
-----------
-This driver implements support for the Texas Instruments ADS1015.
+This driver implements support for the Texas Instruments ADS1015/ADS1115.
-This device is a 12-bit A-D converter with 4 inputs.
+This device is a 12/16-bit A-D converter with 4 inputs.
The inputs can be used single ended or in certain differential combinations.
diff --git a/Documentation/hwmon/htu21 b/Documentation/hwmon/htu21
new file mode 100644
index 000000000000..f39a215fb6ae
--- /dev/null
+++ b/Documentation/hwmon/htu21
@@ -0,0 +1,46 @@
+Kernel driver htu21
+===================
+
+Supported chips:
+ * Measurement Specialties HTU21D
+ Prefix: 'htu21'
+ Addresses scanned: none
+ Datasheet: Publicly available at the Measurement Specialties website
+ http://www.meas-spec.com/downloads/HTU21D.pdf
+
+
+Author:
+ William Markezana <william.markezana@meas-spec.com>
+
+Description
+-----------
+
+The HTU21D is a humidity and temperature sensor in a DFN package of
+only 3 x 3 mm footprint and 0.9 mm height.
+
+The devices communicate with the I2C protocol. All sensors are set to the
+same I2C address 0x40, so an entry with I2C_BOARD_INFO("htu21", 0x40) can
+be used in the board setup code.
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices
+for details.
+
+sysfs-Interface
+---------------
+
+temp1_input - temperature input
+humidity1_input - humidity input
+
+Notes
+-----
+
+The driver uses the default resolution settings of 12 bit for humidity and 14
+bit for temperature, which results in typical measurement times of 11 ms for
+humidity and 44 ms for temperature. To keep self heating below 0.1 degree
+Celsius, the device should not be active for more than 10% of the time. For
+this reason, the driver performs no more than two measurements per second and
+reports cached information if polled more frequently.
+
+Different resolutions, the on-chip heater, using the CRC checksum and reading
+the serial number are not supported yet.
diff --git a/Documentation/hwmon/k10temp b/Documentation/hwmon/k10temp
index 90956b618025..4dfdc8f83633 100644
--- a/Documentation/hwmon/k10temp
+++ b/Documentation/hwmon/k10temp
@@ -12,6 +12,7 @@ Supported chips:
* AMD Family 12h processors: "Llano" (E2/A4/A6/A8-Series)
* AMD Family 14h processors: "Brazos" (C/E/G/Z-Series)
* AMD Family 15h processors: "Bulldozer" (FX-Series), "Trinity"
+* AMD Family 16h processors: "Kabini"
Prefix: 'k10temp'
Addresses scanned: PCI space