diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/ibmpowernv | 43 | ||||
| -rw-r--r-- | Documentation/hwmon/max34440 | 16 | ||||
| -rw-r--r-- | Documentation/hwmon/mlxreg-fan | 60 | ||||
| -rw-r--r-- | Documentation/hwmon/npcm750-pwm-fan | 22 | ||||
| -rw-r--r-- | Documentation/hwmon/sysfs-interface | 48 |
5 files changed, 183 insertions, 6 deletions
diff --git a/Documentation/hwmon/ibmpowernv b/Documentation/hwmon/ibmpowernv index 8826ba29db36..56468258711f 100644 --- a/Documentation/hwmon/ibmpowernv +++ b/Documentation/hwmon/ibmpowernv @@ -33,9 +33,48 @@ fanX_input Measured RPM value. fanX_min Threshold RPM for alert generation. fanX_fault 0: No fail condition 1: Failing fan + tempX_input Measured ambient temperature. tempX_max Threshold ambient temperature for alert generation. -inX_input Measured power supply voltage +tempX_highest Historical maximum temperature +tempX_lowest Historical minimum temperature +tempX_enable Enable/disable all temperature sensors belonging to the + sub-group. In POWER9, this attribute corresponds to + each OCC. Using this attribute each OCC can be asked to + disable/enable all of its temperature sensors. + 1: Enable + 0: Disable + +inX_input Measured power supply voltage (millivolt) inX_fault 0: No fail condition. 1: Failing power supply. -power1_input System power consumption (microWatt) +inX_highest Historical maximum voltage +inX_lowest Historical minimum voltage +inX_enable Enable/disable all voltage sensors belonging to the + sub-group. In POWER9, this attribute corresponds to + each OCC. Using this attribute each OCC can be asked to + disable/enable all of its voltage sensors. + 1: Enable + 0: Disable + +powerX_input Power consumption (microWatt) +powerX_input_highest Historical maximum power +powerX_input_lowest Historical minimum power +powerX_enable Enable/disable all power sensors belonging to the + sub-group. In POWER9, this attribute corresponds to + each OCC. Using this attribute each OCC can be asked to + disable/enable all of its power sensors. + 1: Enable + 0: Disable + +currX_input Measured current (milliampere) +currX_highest Historical maximum current +currX_lowest Historical minimum current +currX_enable Enable/disable all current sensors belonging to the + sub-group. In POWER9, this attribute corresponds to + each OCC. Using this attribute each OCC can be asked to + disable/enable all of its current sensors. + 1: Enable + 0: Disable + +energyX_input Cumulative energy (microJoule) diff --git a/Documentation/hwmon/max34440 b/Documentation/hwmon/max34440 index 9ba6587b7657..b2de8fa49273 100644 --- a/Documentation/hwmon/max34440 +++ b/Documentation/hwmon/max34440 @@ -16,6 +16,11 @@ Supported chips: Prefixes: 'max34446' Addresses scanned: - Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX34446.pdf + * Maxim MAX34451 + PMBus 16-Channel V/I Monitor and 12-Channel Sequencer/Marginer + Prefixes: 'max34451' + Addresses scanned: - + Datasheet: http://datasheets.maximintegrated.com/en/ds/MAX34451.pdf * Maxim MAX34460 PMBus 12-Channel Voltage Monitor & Sequencer Prefix: 'max34460' @@ -36,9 +41,10 @@ Description This driver supports hardware monitoring for Maxim MAX34440 PMBus 6-Channel Power-Supply Manager, MAX34441 PMBus 5-Channel Power-Supply Manager and Intelligent Fan Controller, and MAX34446 PMBus Power-Supply Data Logger. -It also supports the MAX34460 and MAX34461 PMBus Voltage Monitor & Sequencers. -The MAX34460 supports 12 voltage channels, and the MAX34461 supports 16 voltage -channels. +It also supports the MAX34451, MAX34460, and MAX34461 PMBus Voltage Monitor & +Sequencers. The MAX34451 supports monitoring voltage or current of 12 channels +based on GIN pins. The MAX34460 supports 12 voltage channels, and the MAX34461 +supports 16 voltage channels. The driver is a client driver to the core PMBus driver. Please see Documentation/hwmon/pmbus for details on PMBus client drivers. @@ -93,7 +99,7 @@ curr[1-6]_max Maximum current. From IOUT_OC_WARN_LIMIT register. curr[1-6]_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. curr[1-6]_max_alarm Current high alarm. From IOUT_OC_WARNING status. curr[1-6]_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. -curr[1-4]_average Historical average current (MAX34446 only). +curr[1-4]_average Historical average current (MAX34446/34451 only). curr[1-6]_highest Historical maximum current. curr[1-6]_reset_history Write any value to reset history. @@ -123,5 +129,7 @@ temp[1-8]_reset_history Write any value to reset history. temp7 and temp8 attributes only exist for MAX34440. MAX34446 only supports temp[1-3]. +MAX34451 supports attribute groups in[1-16] (or curr[1-16] based on input pins) +and temp[1-5]. MAX34460 supports attribute groups in[1-12] and temp[1-5]. MAX34461 supports attribute groups in[1-16] and temp[1-5]. diff --git a/Documentation/hwmon/mlxreg-fan b/Documentation/hwmon/mlxreg-fan new file mode 100644 index 000000000000..fc531c6978d4 --- /dev/null +++ b/Documentation/hwmon/mlxreg-fan @@ -0,0 +1,60 @@ +Kernel driver mlxreg-fan +======================== + +Provides FAN control for the next Mellanox systems: +QMB700, equipped with 40x200GbE InfiniBand ports; +MSN3700, equipped with 32x200GbE or 16x400GbE Ethernet ports; +MSN3410, equipped with 6x400GbE plus 48x50GbE Ethernet ports; +MSN3800, equipped with 64x1000GbE Ethernet ports; +These are the Top of the Rack systems, equipped with Mellanox switch +board with Mellanox Quantum or Spectrume-2 devices. +FAN controller is implemented by the programmable device logic. + +The default registers offsets set within the programmable device is as +following: +- pwm1 0xe3 +- fan1 (tacho1) 0xe4 +- fan2 (tacho2) 0xe5 +- fan3 (tacho3) 0xe6 +- fan4 (tacho4) 0xe7 +- fan5 (tacho5) 0xe8 +- fan6 (tacho6) 0xe9 +- fan7 (tacho7) 0xea +- fan8 (tacho8) 0xeb +- fan9 (tacho9) 0xec +- fan10 (tacho10) 0xed +- fan11 (tacho11) 0xee +- fan12 (tacho12) 0xef +This setup can be re-programmed with other registers. + +Author: Vadim Pasternak <vadimp@mellanox.com> + +Description +----------- + +The driver implements a simple interface for driving a fan connected to +a PWM output and tachometer inputs. +This driver obtains PWM and tachometers registers location according to +the system configuration and creates FAN/PWM hwmon objects and a cooling +device. PWM and tachometers are sensed through the on-board programmable +device, which exports its register map. This device could be attached to +any bus type, for which register mapping is supported. +Single instance is created with one PWM control, up to 12 tachometers and +one cooling device. It could be as many instances as programmable device +supports. +The driver exposes the fan to the user space through the hwmon's and +thermal's sysfs interfaces. + +/sys files in hwmon subsystem +----------------------------- + +fan[1-12]_fault - RO files for tachometers TACH1-TACH12 fault indication +fan[1-12]_input - RO files for tachometers TACH1-TACH12 input (in RPM) +pwm1 - RW file for fan[1-12] target duty cycle (0..255) + +/sys files in thermal subsystem +------------------------------- + +cur_state - RW file for current cooling state of the cooling device + (0..max_state) +max_state - RO file for maximum cooling state of the cooling device diff --git a/Documentation/hwmon/npcm750-pwm-fan b/Documentation/hwmon/npcm750-pwm-fan new file mode 100644 index 000000000000..6156ef7398e6 --- /dev/null +++ b/Documentation/hwmon/npcm750-pwm-fan @@ -0,0 +1,22 @@ +Kernel driver npcm750-pwm-fan +============================= + +Supported chips: + NUVOTON NPCM750/730/715/705 + +Authors: + <tomer.maimon@nuvoton.com> + +Description: +------------ +This driver implements support for NUVOTON NPCM7XX PWM and Fan Tacho +controller. The PWM controller supports up to 8 PWM outputs. The Fan tacho +controller supports up to 16 tachometer inputs. + +The driver provides the following sensor accesses in sysfs: + +fanX_input ro provide current fan rotation value in RPM as reported + by the fan to the device. + +pwmX rw get or set PWM fan control value. This is an integer + value between 0(off) and 255(full speed). diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index fc337c317c67..2b9e1005d88b 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -171,6 +171,13 @@ in[0-*]_label Suggested voltage channel label. user-space. RO +in[0-*]_enable + Enable or disable the sensors. + When disabled the sensor read will return -ENODATA. + 1: Enable + 0: Disable + RW + cpu[0-*]_vid CPU core reference voltage. Unit: millivolt RO @@ -236,6 +243,13 @@ fan[1-*]_label Suggested fan channel label. In all other cases, the label is provided by user-space. RO +fan[1-*]_enable + Enable or disable the sensors. + When disabled the sensor read will return -ENODATA. + 1: Enable + 0: Disable + RW + Also see the Alarms section for status flags associated with fans. @@ -409,6 +423,13 @@ temp_reset_history Reset temp_lowest and temp_highest for all sensors WO +temp[1-*]_enable + Enable or disable the sensors. + When disabled the sensor read will return -ENODATA. + 1: Enable + 0: Disable + RW + Some chips measure temperature using external thermistors and an ADC, and report the temperature measurement as a voltage. Converting this voltage back to a temperature (or the other way around for limits) requires @@ -468,6 +489,13 @@ curr_reset_history Reset currX_lowest and currX_highest for all sensors WO +curr[1-*]_enable + Enable or disable the sensors. + When disabled the sensor read will return -ENODATA. + 1: Enable + 0: Disable + RW + Also see the Alarms section for status flags associated with currents. ********* @@ -566,6 +594,13 @@ power[1-*]_crit Critical maximum power. Unit: microWatt RW +power[1-*]_enable Enable or disable the sensors. + When disabled the sensor read will return + -ENODATA. + 1: Enable + 0: Disable + RW + Also see the Alarms section for status flags associated with power readings. ********** @@ -576,6 +611,12 @@ energy[1-*]_input Cumulative energy use Unit: microJoule RO +energy[1-*]_enable Enable or disable the sensors. + When disabled the sensor read will return + -ENODATA. + 1: Enable + 0: Disable + RW ************ * Humidity * @@ -586,6 +627,13 @@ humidity[1-*]_input Humidity RO +humidity[1-*]_enable Enable or disable the sensors + When disabled the sensor read will return + -ENODATA. + 1: Enable + 0: Disable + RW + ********** * Alarms * ********** |