summaryrefslogtreecommitdiff
path: root/Documentation/networking/devlink/mlx5.rst
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/networking/devlink/mlx5.rst')
-rw-r--r--Documentation/networking/devlink/mlx5.rst288
1 files changed, 288 insertions, 0 deletions
diff --git a/Documentation/networking/devlink/mlx5.rst b/Documentation/networking/devlink/mlx5.rst
new file mode 100644
index 000000000000..702f204a3dbd
--- /dev/null
+++ b/Documentation/networking/devlink/mlx5.rst
@@ -0,0 +1,288 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+====================
+mlx5 devlink support
+====================
+
+This document describes the devlink features implemented by the ``mlx5``
+device driver.
+
+Parameters
+==========
+
+.. list-table:: Generic parameters implemented
+
+ * - Name
+ - Mode
+ - Validation
+ * - ``enable_roce``
+ - driverinit
+ - Type: Boolean
+
+ If the device supports RoCE disablement, RoCE enablement state controls
+ device support for RoCE capability. Otherwise, the control occurs in the
+ driver stack. When RoCE is disabled at the driver level, only raw
+ ethernet QPs are supported.
+ * - ``io_eq_size``
+ - driverinit
+ - The range is between 64 and 4096.
+ * - ``event_eq_size``
+ - driverinit
+ - The range is between 64 and 4096.
+ * - ``max_macs``
+ - driverinit
+ - The range is between 1 and 2^31. Only power of 2 values are supported.
+
+The ``mlx5`` driver also implements the following driver-specific
+parameters.
+
+.. list-table:: Driver-specific parameters implemented
+ :widths: 5 5 5 85
+
+ * - Name
+ - Type
+ - Mode
+ - Description
+ * - ``flow_steering_mode``
+ - string
+ - runtime
+ - Controls the flow steering mode of the driver
+
+ * ``dmfs`` Device managed flow steering. In DMFS mode, the HW
+ steering entities are created and managed through firmware.
+ * ``smfs`` Software managed flow steering. In SMFS mode, the HW
+ steering entities are created and manage through the driver without
+ firmware intervention.
+
+ SMFS mode is faster and provides better rule insertion rate compared to
+ default DMFS mode.
+ * - ``fdb_large_groups``
+ - u32
+ - driverinit
+ - Control the number of large groups (size > 1) in the FDB table.
+
+ * The default value is 15, and the range is between 1 and 1024.
+ * - ``esw_multiport``
+ - Boolean
+ - runtime
+ - Control MultiPort E-Switch shared fdb mode.
+
+ An experimental mode where a single E-Switch is used and all the vports
+ and physical ports on the NIC are connected to it.
+
+ An example is to send traffic from a VF that is created on PF0 to an
+ uplink that is natively associated with the uplink of PF1
+
+ Note: Future devices, ConnectX-8 and onward, will eventually have this
+ as the default to allow forwarding between all NIC ports in a single
+ E-switch environment and the dual E-switch mode will likely get
+ deprecated.
+
+ Default: disabled
+ * - ``esw_port_metadata``
+ - Boolean
+ - runtime
+ - When applicable, disabling eswitch metadata can increase packet rate up
+ to 20% depending on the use case and packet sizes.
+
+ Eswitch port metadata state controls whether to internally tag packets
+ with metadata. Metadata tagging must be enabled for multi-port RoCE,
+ failover between representors and stacked devices. By default metadata is
+ enabled on the supported devices in E-switch. Metadata is applicable only
+ for E-switch in switchdev mode and users may disable it when NONE of the
+ below use cases will be in use:
+ 1. HCA is in Dual/multi-port RoCE mode.
+ 2. VF/SF representor bonding (Usually used for Live migration)
+ 3. Stacked devices
+
+ When metadata is disabled, the above use cases will fail to initialize if
+ users try to enable them.
+ * - ``hairpin_num_queues``
+ - u32
+ - driverinit
+ - We refer to a TC NIC rule that involves forwarding as "hairpin".
+ Hairpin queues are mlx5 hardware specific implementation for hardware
+ forwarding of such packets.
+
+ Control the number of hairpin queues.
+ * - ``hairpin_queue_size``
+ - u32
+ - driverinit
+ - Control the size (in packets) of the hairpin queues.
+
+The ``mlx5`` driver supports reloading via ``DEVLINK_CMD_RELOAD``
+
+Info versions
+=============
+
+The ``mlx5`` driver reports the following versions
+
+.. list-table:: devlink info versions implemented
+ :widths: 5 5 90
+
+ * - Name
+ - Type
+ - Description
+ * - ``fw.psid``
+ - fixed
+ - Used to represent the board id of the device.
+ * - ``fw.version``
+ - stored, running
+ - Three digit major.minor.subminor firmware version number.
+
+Health reporters
+================
+
+tx reporter
+-----------
+The tx reporter is responsible for reporting and recovering of the following three error scenarios:
+
+- tx timeout
+ Report on kernel tx timeout detection.
+ Recover by searching lost interrupts.
+- tx error completion
+ Report on error tx completion.
+ Recover by flushing the tx queue and reset it.
+- tx PTP port timestamping CQ unhealthy
+ Report too many CQEs never delivered on port ts CQ.
+ Recover by flushing and re-creating all PTP channels.
+
+tx reporter also support on demand diagnose callback, on which it provides
+real time information of its send queues status.
+
+User commands examples:
+
+- Diagnose send queues status::
+
+ $ devlink health diagnose pci/0000:82:00.0 reporter tx
+
+.. note::
+ This command has valid output only when interface is up, otherwise the command has empty output.
+
+- Show number of tx errors indicated, number of recover flows ended successfully,
+ is autorecover enabled and graceful period from last recover::
+
+ $ devlink health show pci/0000:82:00.0 reporter tx
+
+rx reporter
+-----------
+The rx reporter is responsible for reporting and recovering of the following two error scenarios:
+
+- rx queues' initialization (population) timeout
+ Population of rx queues' descriptors on ring initialization is done
+ in napi context via triggering an irq. In case of a failure to get
+ the minimum amount of descriptors, a timeout would occur, and
+ descriptors could be recovered by polling the EQ (Event Queue).
+- rx completions with errors (reported by HW on interrupt context)
+ Report on rx completion error.
+ Recover (if needed) by flushing the related queue and reset it.
+
+rx reporter also supports on demand diagnose callback, on which it
+provides real time information of its receive queues' status.
+
+- Diagnose rx queues' status and corresponding completion queue::
+
+ $ devlink health diagnose pci/0000:82:00.0 reporter rx
+
+.. note::
+ This command has valid output only when interface is up. Otherwise, the command has empty output.
+
+- Show number of rx errors indicated, number of recover flows ended successfully,
+ is autorecover enabled, and graceful period from last recover::
+
+ $ devlink health show pci/0000:82:00.0 reporter rx
+
+fw reporter
+-----------
+The fw reporter implements `diagnose` and `dump` callbacks.
+It follows symptoms of fw error such as fw syndrome by triggering
+fw core dump and storing it into the dump buffer.
+The fw reporter diagnose command can be triggered any time by the user to check
+current fw status.
+
+User commands examples:
+
+- Check fw heath status::
+
+ $ devlink health diagnose pci/0000:82:00.0 reporter fw
+
+- Read FW core dump if already stored or trigger new one::
+
+ $ devlink health dump show pci/0000:82:00.0 reporter fw
+
+.. note::
+ This command can run only on the PF which has fw tracer ownership,
+ running it on other PF or any VF will return "Operation not permitted".
+
+fw fatal reporter
+-----------------
+The fw fatal reporter implements `dump` and `recover` callbacks.
+It follows fatal errors indications by CR-space dump and recover flow.
+The CR-space dump uses vsc interface which is valid even if the FW command
+interface is not functional, which is the case in most FW fatal errors.
+The recover function runs recover flow which reloads the driver and triggers fw
+reset if needed.
+On firmware error, the health buffer is dumped into the dmesg. The log
+level is derived from the error's severity (given in health buffer).
+
+User commands examples:
+
+- Run fw recover flow manually::
+
+ $ devlink health recover pci/0000:82:00.0 reporter fw_fatal
+
+- Read FW CR-space dump if already stored or trigger new one::
+
+ $ devlink health dump show pci/0000:82:00.1 reporter fw_fatal
+
+.. note::
+ This command can run only on PF.
+
+vnic reporter
+-------------
+The vnic reporter implements only the `diagnose` callback.
+It is responsible for querying the vnic diagnostic counters from fw and displaying
+them in realtime.
+
+Description of the vnic counters:
+
+- total_q_under_processor_handle
+ number of queues in an error state due to
+ an async error or errored command.
+- send_queue_priority_update_flow
+ number of QP/SQ priority/SL update events.
+- cq_overrun
+ number of times CQ entered an error state due to an overflow.
+- async_eq_overrun
+ number of times an EQ mapped to async events was overrun.
+ comp_eq_overrun number of times an EQ mapped to completion events was
+ overrun.
+- quota_exceeded_command
+ number of commands issued and failed due to quota exceeded.
+- invalid_command
+ number of commands issued and failed dues to any reason other than quota
+ exceeded.
+- nic_receive_steering_discard
+ number of packets that completed RX flow
+ steering but were discarded due to a mismatch in flow table.
+- generated_pkt_steering_fail
+ number of packets generated by the VNIC experiencing unexpected steering
+ failure (at any point in steering flow).
+- handled_pkt_steering_fail
+ number of packets handled by the VNIC experiencing unexpected steering
+ failure (at any point in steering flow owned by the VNIC, including the FDB
+ for the eswitch owner).
+
+User commands examples:
+
+- Diagnose PF/VF vnic counters::
+
+ $ devlink health diagnose pci/0000:82:00.1 reporter vnic
+
+- Diagnose representor vnic counters (performed by supplying devlink port of the
+ representor, which can be obtained via devlink port command)::
+
+ $ devlink health diagnose pci/0000:82:00.1/65537 reporter vnic
+
+.. note::
+ This command can run over all interfaces such as PF/VF and representor ports.