summaryrefslogtreecommitdiff
path: root/Documentation/networking/e1000.rst
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/networking/e1000.rst')
-rw-r--r--Documentation/networking/e1000.rst187
1 files changed, 112 insertions, 75 deletions
diff --git a/Documentation/networking/e1000.rst b/Documentation/networking/e1000.rst
index 144b87eef153..f10dd4086921 100644
--- a/Documentation/networking/e1000.rst
+++ b/Documentation/networking/e1000.rst
@@ -34,7 +34,8 @@ Command Line Parameters
The default value for each parameter is generally the recommended setting,
unless otherwise noted.
-NOTES: For more information about the AutoNeg, Duplex, and Speed
+NOTES:
+ For more information about the AutoNeg, Duplex, and Speed
parameters, see the "Speed and Duplex Configuration" section in
this document.
@@ -45,22 +46,27 @@ NOTES: For more information about the AutoNeg, Duplex, and Speed
AutoNeg
-------
+
(Supported only on adapters with copper connections)
-Valid Range: 0x01-0x0F, 0x20-0x2F
-Default Value: 0x2F
+
+:Valid Range: 0x01-0x0F, 0x20-0x2F
+:Default Value: 0x2F
This parameter is a bit-mask that specifies the speed and duplex settings
advertised by the adapter. When this parameter is used, the Speed and
Duplex parameters must not be specified.
-NOTE: Refer to the Speed and Duplex section of this readme for more
+NOTE:
+ Refer to the Speed and Duplex section of this readme for more
information on the AutoNeg parameter.
Duplex
------
+
(Supported only on adapters with copper connections)
-Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
-Default Value: 0
+
+:Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
+:Default Value: 0
This defines the direction in which data is allowed to flow. Can be
either one or two-directional. If both Duplex and the link partner are
@@ -70,18 +76,22 @@ duplex.
FlowControl
-----------
-Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
-Default Value: Reads flow control settings from the EEPROM
+
+:Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
+:Default Value: Reads flow control settings from the EEPROM
This parameter controls the automatic generation(Tx) and response(Rx)
to Ethernet PAUSE frames.
InterruptThrottleRate
---------------------
+
(not supported on Intel(R) 82542, 82543 or 82544-based adapters)
-Valid Range: 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
- 4=simplified balancing)
-Default Value: 3
+
+:Valid Range:
+ 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
+ 4=simplified balancing)
+:Default Value: 3
The driver can limit the amount of interrupts per second that the adapter
will generate for incoming packets. It does this by writing a value to the
@@ -135,13 +145,15 @@ Setting InterruptThrottleRate to 0 turns off any interrupt moderation
and may improve small packet latency, but is generally not suitable
for bulk throughput traffic.
-NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
+NOTE:
+ InterruptThrottleRate takes precedence over the TxAbsIntDelay and
RxAbsIntDelay parameters. In other words, minimizing the receive
and/or transmit absolute delays does not force the controller to
generate more interrupts than what the Interrupt Throttle Rate
allows.
-CAUTION: If you are using the Intel(R) PRO/1000 CT Network Connection
+CAUTION:
+ If you are using the Intel(R) PRO/1000 CT Network Connection
(controller 82547), setting InterruptThrottleRate to a value
greater than 75,000, may hang (stop transmitting) adapters
under certain network conditions. If this occurs a NETDEV
@@ -151,7 +163,8 @@ CAUTION: If you are using the Intel(R) PRO/1000 CT Network Connection
hang, ensure that InterruptThrottleRate is set no greater
than 75,000 and is not set to 0.
-NOTE: When e1000 is loaded with default settings and multiple adapters
+NOTE:
+ When e1000 is loaded with default settings and multiple adapters
are in use simultaneously, the CPU utilization may increase non-
linearly. In order to limit the CPU utilization without impacting
the overall throughput, we recommend that you load the driver as
@@ -168,9 +181,11 @@ NOTE: When e1000 is loaded with default settings and multiple adapters
RxDescriptors
-------------
-Valid Range: 48-256 for 82542 and 82543-based adapters
- 48-4096 for all other supported adapters
-Default Value: 256
+
+:Valid Range:
+ - 48-256 for 82542 and 82543-based adapters
+ - 48-4096 for all other supported adapters
+:Default Value: 256
This value specifies the number of receive buffer descriptors allocated
by the driver. Increasing this value allows the driver to buffer more
@@ -180,15 +195,17 @@ Each descriptor is 16 bytes. A receive buffer is also allocated for each
descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending
on the MTU setting. The maximum MTU size is 16110.
-NOTE: MTU designates the frame size. It only needs to be set for Jumbo
+NOTE:
+ MTU designates the frame size. It only needs to be set for Jumbo
Frames. Depending on the available system resources, the request
for a higher number of receive descriptors may be denied. In this
case, use a lower number.
RxIntDelay
----------
-Valid Range: 0-65535 (0=off)
-Default Value: 0
+
+:Valid Range: 0-65535 (0=off)
+:Default Value: 0
This value delays the generation of receive interrupts in units of 1.024
microseconds. Receive interrupt reduction can improve CPU efficiency if
@@ -198,7 +215,8 @@ of TCP traffic. If the system is reporting dropped receives, this value
may be set too high, causing the driver to run out of available receive
descriptors.
-CAUTION: When setting RxIntDelay to a value other than 0, adapters may
+CAUTION:
+ When setting RxIntDelay to a value other than 0, adapters may
hang (stop transmitting) under certain network conditions. If
this occurs a NETDEV WATCHDOG message is logged in the system
event log. In addition, the controller is automatically reset,
@@ -207,9 +225,11 @@ CAUTION: When setting RxIntDelay to a value other than 0, adapters may
RxAbsIntDelay
-------------
+
(This parameter is supported only on 82540, 82545 and later adapters.)
-Valid Range: 0-65535 (0=off)
-Default Value: 128
+
+:Valid Range: 0-65535 (0=off)
+:Default Value: 128
This value, in units of 1.024 microseconds, limits the delay in which a
receive interrupt is generated. Useful only if RxIntDelay is non-zero,
@@ -220,9 +240,11 @@ conditions.
Speed
-----
+
(This parameter is supported only on adapters with copper connections.)
-Valid Settings: 0, 10, 100, 1000
-Default Value: 0 (auto-negotiate at all supported speeds)
+
+:Valid Settings: 0, 10, 100, 1000
+:Default Value: 0 (auto-negotiate at all supported speeds)
Speed forces the line speed to the specified value in megabits per second
(Mbps). If this parameter is not specified or is set to 0 and the link
@@ -231,22 +253,26 @@ speed. Duplex should also be set when Speed is set to either 10 or 100.
TxDescriptors
-------------
-Valid Range: 48-256 for 82542 and 82543-based adapters
- 48-4096 for all other supported adapters
-Default Value: 256
+
+:Valid Range:
+ - 48-256 for 82542 and 82543-based adapters
+ - 48-4096 for all other supported adapters
+:Default Value: 256
This value is the number of transmit descriptors allocated by the driver.
Increasing this value allows the driver to queue more transmits. Each
descriptor is 16 bytes.
-NOTE: Depending on the available system resources, the request for a
+NOTE:
+ Depending on the available system resources, the request for a
higher number of transmit descriptors may be denied. In this case,
use a lower number.
TxIntDelay
----------
-Valid Range: 0-65535 (0=off)
-Default Value: 8
+
+:Valid Range: 0-65535 (0=off)
+:Default Value: 8
This value delays the generation of transmit interrupts in units of
1.024 microseconds. Transmit interrupt reduction can improve CPU
@@ -256,9 +282,11 @@ causing the driver to run out of available transmit descriptors.
TxAbsIntDelay
-------------
+
(This parameter is supported only on 82540, 82545 and later adapters.)
-Valid Range: 0-65535 (0=off)
-Default Value: 32
+
+:Valid Range: 0-65535 (0=off)
+:Default Value: 32
This value, in units of 1.024 microseconds, limits the delay in which a
transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
@@ -269,18 +297,21 @@ network conditions.
XsumRX
------
+
(This parameter is NOT supported on the 82542-based adapter.)
-Valid Range: 0-1
-Default Value: 1
+
+:Valid Range: 0-1
+:Default Value: 1
A value of '1' indicates that the driver should enable IP checksum
offload for received packets (both UDP and TCP) to the adapter hardware.
Copybreak
---------
-Valid Range: 0-xxxxxxx (0=off)
-Default Value: 256
-Usage: modprobe e1000.ko copybreak=128
+
+:Valid Range: 0-xxxxxxx (0=off)
+:Default Value: 256
+:Usage: modprobe e1000.ko copybreak=128
Driver copies all packets below or equaling this size to a fresh RX
buffer before handing it up the stack.
@@ -292,8 +323,9 @@ it is also available during runtime at
SmartPowerDownEnable
--------------------
-Valid Range: 0-1
-Default Value: 0 (disabled)
+
+:Valid Range: 0-1
+:Default Value: 0 (disabled)
Allows PHY to turn off in lower power states. The user can turn off
this parameter in supported chipsets.
@@ -309,14 +341,14 @@ fiber interface board only links at 1000 Mbps full-duplex.
For copper-based boards, the keywords interact as follows:
- The default operation is auto-negotiate. The board advertises all
+- The default operation is auto-negotiate. The board advertises all
supported speed and duplex combinations, and it links at the highest
common speed and duplex mode IF the link partner is set to auto-negotiate.
- If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
+- If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
is advertised (The 1000BaseT spec requires auto-negotiation.)
- If Speed = 10 or 100, then both Speed and Duplex should be set. Auto-
+- If Speed = 10 or 100, then both Speed and Duplex should be set. Auto-
negotiation is disabled, and the AutoNeg parameter is ignored. Partner
SHOULD also be forced.
@@ -328,13 +360,15 @@ process.
The parameter may be specified as either a decimal or hexadecimal value as
determined by the bitmap below.
+============== ====== ====== ======= ======= ====== ====== ======= ======
Bit position 7 6 5 4 3 2 1 0
Decimal Value 128 64 32 16 8 4 2 1
Hex value 80 40 20 10 8 4 2 1
Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10
Duplex Full Full Half Full Half
+============== ====== ====== ======= ======= ====== ====== ======= ======
-Some examples of using AutoNeg:
+Some examples of using AutoNeg::
modprobe e1000 AutoNeg=0x01 (Restricts autonegotiation to 10 Half)
modprobe e1000 AutoNeg=1 (Same as above)
@@ -357,56 +391,59 @@ Additional Configurations
Jumbo Frames
------------
-Jumbo Frames support is enabled by changing the MTU to a value larger
-than the default of 1500. Use the ifconfig command to increase the MTU
-size. For example::
+
+ Jumbo Frames support is enabled by changing the MTU to a value larger than
+ the default of 1500. Use the ifconfig command to increase the MTU size.
+ For example::
ifconfig eth<x> mtu 9000 up
-This setting is not saved across reboots. It can be made permanent if
-you add::
+ This setting is not saved across reboots. It can be made permanent if
+ you add::
MTU=9000
-to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>. This example
-applies to the Red Hat distributions; other distributions may store this
-setting in a different location.
+ to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>. This example
+ applies to the Red Hat distributions; other distributions may store this
+ setting in a different location.
+
+Notes:
+ Degradation in throughput performance may be observed in some Jumbo frames
+ environments. If this is observed, increasing the application's socket buffer
+ size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help.
+ See the specific application manual and /usr/src/linux*/Documentation/
+ networking/ip-sysctl.txt for more details.
-Notes: Degradation in throughput performance may be observed in some
-Jumbo frames environments. If this is observed, increasing the
-application's socket buffer size and/or increasing the
-/proc/sys/net/ipv4/tcp_*mem entry values may help. See the specific
-application manual and /usr/src/linux*/Documentation/
-networking/ip-sysctl.txt for more details.
+ - The maximum MTU setting for Jumbo Frames is 16110. This value coincides
+ with the maximum Jumbo Frames size of 16128.
-- The maximum MTU setting for Jumbo Frames is 16110. This value
- coincides with the maximum Jumbo Frames size of 16128.
+ - Using Jumbo frames at 10 or 100 Mbps is not supported and may result in
+ poor performance or loss of link.
-- Using Jumbo frames at 10 or 100 Mbps is not supported and may result
- in poor performance or loss of link.
+ - Adapters based on the Intel(R) 82542 and 82573V/E controller do not
+ support Jumbo Frames. These correspond to the following product names::
-- Adapters based on the Intel(R) 82542 and 82573V/E controller do not
- support Jumbo Frames. These correspond to the following product names:
- Intel(R) PRO/1000 Gigabit Server Adapter Intel(R) PRO/1000 PM Network
- Connection
+ Intel(R) PRO/1000 Gigabit Server Adapter
+ Intel(R) PRO/1000 PM Network Connection
ethtool
-------
-The driver utilizes the ethtool interface for driver configuration and
-diagnostics, as well as displaying statistical information. The ethtool
-version 1.6 or later is required for this functionality.
-The latest release of ethtool can be found from
-https://www.kernel.org/pub/software/network/ethtool/
+ The driver utilizes the ethtool interface for driver configuration and
+ diagnostics, as well as displaying statistical information. The ethtool
+ version 1.6 or later is required for this functionality.
+
+ The latest release of ethtool can be found from
+ https://www.kernel.org/pub/software/network/ethtool/
Enabling Wake on LAN* (WoL)
---------------------------
-WoL is configured through the ethtool* utility.
-WoL will be enabled on the system during the next shut down or reboot.
-For this driver version, in order to enable WoL, the e1000 driver must be
-loaded when shutting down or rebooting the system.
+ WoL is configured through the ethtool* utility.
+ WoL will be enabled on the system during the next shut down or reboot.
+ For this driver version, in order to enable WoL, the e1000 driver must be
+ loaded when shutting down or rebooting the system.
Support
=======