summaryrefslogtreecommitdiff
path: root/Documentation/networking/multiqueue.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/networking/multiqueue.txt')
-rw-r--r--Documentation/networking/multiqueue.txt79
1 files changed, 1 insertions, 78 deletions
diff --git a/Documentation/networking/multiqueue.txt b/Documentation/networking/multiqueue.txt
index ea5a42e8f79f..e6dc1ee9e8f1 100644
--- a/Documentation/networking/multiqueue.txt
+++ b/Documentation/networking/multiqueue.txt
@@ -3,19 +3,11 @@
===========================================
Section 1: Base driver requirements for implementing multiqueue support
-Section 2: Qdisc support for multiqueue devices
-Section 3: Brief howto using PRIO or RR for multiqueue devices
-
Intro: Kernel support for multiqueue devices
---------------------------------------------------------
-Kernel support for multiqueue devices is only an API that is presented to the
-netdevice layer for base drivers to implement. This feature is part of the
-core networking stack, and all network devices will be running on the
-multiqueue-aware stack. If a base driver only has one queue, then these
-changes are transparent to that driver.
-
+Kernel support for multiqueue devices is always present.
Section 1: Base driver requirements for implementing multiqueue support
-----------------------------------------------------------------------
@@ -43,73 +35,4 @@ bitmap on device initialization. Below is an example from e1000:
netdev->features |= NETIF_F_MULTI_QUEUE;
#endif
-
-Section 2: Qdisc support for multiqueue devices
------------------------------------------------
-
-Currently two qdiscs support multiqueue devices. A new round-robin qdisc,
-sch_rr, and sch_prio. The qdisc is responsible for classifying the skb's to
-bands and queues, and will store the queue mapping into skb->queue_mapping.
-Use this field in the base driver to determine which queue to send the skb
-to.
-
-sch_rr has been added for hardware that doesn't want scheduling policies from
-software, so it's a straight round-robin qdisc. It uses the same syntax and
-classification priomap that sch_prio uses, so it should be intuitive to
-configure for people who've used sch_prio.
-
-In order to utilitize the multiqueue features of the qdiscs, the network
-device layer needs to enable multiple queue support. This can be done by
-selecting NETDEVICES_MULTIQUEUE under Drivers.
-
-The PRIO qdisc naturally plugs into a multiqueue device. If
-NETDEVICES_MULTIQUEUE is selected, then on qdisc load, the number of
-bands requested is compared to the number of queues on the hardware. If they
-are equal, it sets a one-to-one mapping up between the queues and bands. If
-they're not equal, it will not load the qdisc. This is the same behavior
-for RR. Once the association is made, any skb that is classified will have
-skb->queue_mapping set, which will allow the driver to properly queue skb's
-to multiple queues.
-
-
-Section 3: Brief howto using PRIO and RR for multiqueue devices
----------------------------------------------------------------
-
-The userspace command 'tc,' part of the iproute2 package, is used to configure
-qdiscs. To add the PRIO qdisc to your network device, assuming the device is
-called eth0, run the following command:
-
-# tc qdisc add dev eth0 root handle 1: prio bands 4 multiqueue
-
-This will create 4 bands, 0 being highest priority, and associate those bands
-to the queues on your NIC. Assuming eth0 has 4 Tx queues, the band mapping
-would look like:
-
-band 0 => queue 0
-band 1 => queue 1
-band 2 => queue 2
-band 3 => queue 3
-
-Traffic will begin flowing through each queue if your TOS values are assigning
-traffic across the various bands. For example, ssh traffic will always try to
-go out band 0 based on TOS -> Linux priority conversion (realtime traffic),
-so it will be sent out queue 0. ICMP traffic (pings) fall into the "normal"
-traffic classification, which is band 1. Therefore pings will be send out
-queue 1 on the NIC.
-
-Note the use of the multiqueue keyword. This is only in versions of iproute2
-that support multiqueue networking devices; if this is omitted when loading
-a qdisc onto a multiqueue device, the qdisc will load and operate the same
-if it were loaded onto a single-queue device (i.e. - sends all traffic to
-queue 0).
-
-Another alternative to multiqueue band allocation can be done by using the
-multiqueue option and specify 0 bands. If this is the case, the qdisc will
-allocate the number of bands to equal the number of queues that the device
-reports, and bring the qdisc online.
-
-The behavior of tc filters remains the same, where it will override TOS priority
-classification.
-
-
Author: Peter P. Waskiewicz Jr. <peter.p.waskiewicz.jr@intel.com>