diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/arcnet.rst | 2 | ||||
| -rw-r--r-- | Documentation/networking/ax25.rst | 2 | ||||
| -rw-r--r-- | Documentation/networking/bareudp.rst | 24 | ||||
| -rw-r--r-- | Documentation/networking/can_ucan_protocol.rst | 4 | ||||
| -rw-r--r-- | Documentation/networking/devlink/devlink-trap.rst | 4 | ||||
| -rw-r--r-- | Documentation/networking/dsa/dsa.rst | 2 | ||||
| -rw-r--r-- | Documentation/networking/ip-sysctl.rst | 2 | ||||
| -rw-r--r-- | Documentation/networking/ipvs-sysctl.rst | 2 | ||||
| -rw-r--r-- | Documentation/networking/rxrpc.rst | 2 |
9 files changed, 27 insertions, 17 deletions
diff --git a/Documentation/networking/arcnet.rst b/Documentation/networking/arcnet.rst index e93d9820f0f1..82fce606c0f0 100644 --- a/Documentation/networking/arcnet.rst +++ b/Documentation/networking/arcnet.rst @@ -434,7 +434,7 @@ can set up your network then: ifconfig arc0 insight route add insight arc0 route add freedom arc0 /* I would use the subnet here (like I said - to to in "single protocol" above), + to in "single protocol" above), but the rest of the subnet unfortunately lies across the PPP link on freedom, which confuses diff --git a/Documentation/networking/ax25.rst b/Documentation/networking/ax25.rst index 824afd7002db..f060cfb1445a 100644 --- a/Documentation/networking/ax25.rst +++ b/Documentation/networking/ax25.rst @@ -6,7 +6,7 @@ AX.25 To use the amateur radio protocols within Linux you will need to get a suitable copy of the AX.25 Utilities. More detailed information about -AX.25, NET/ROM and ROSE, associated programs and and utilities can be +AX.25, NET/ROM and ROSE, associated programs and utilities can be found on http://www.linux-ax25.org. There is an active mailing list for discussing Linux amateur radio matters diff --git a/Documentation/networking/bareudp.rst b/Documentation/networking/bareudp.rst index 465a8b251bfe..b9d04ee6dac1 100644 --- a/Documentation/networking/bareudp.rst +++ b/Documentation/networking/bareudp.rst @@ -8,9 +8,8 @@ There are various L3 encapsulation standards using UDP being discussed to leverage the UDP based load balancing capability of different networks. MPLSoUDP (__ https://tools.ietf.org/html/rfc7510) is one among them. -The Bareudp tunnel module provides a generic L3 encapsulation tunnelling -support for tunnelling different L3 protocols like MPLS, IP, NSH etc. inside -a UDP tunnel. +The Bareudp tunnel module provides a generic L3 encapsulation support for +tunnelling different L3 protocols like MPLS, IP, NSH etc. inside a UDP tunnel. Special Handling ---------------- @@ -26,7 +25,7 @@ Usage 1) Device creation & deletion - a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype 0x8847. + a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls_uc This creates a bareudp tunnel device which tunnels L3 traffic with ethertype 0x8847 (MPLS traffic). The destination port of the UDP header will be set to @@ -34,14 +33,21 @@ Usage b) ip link delete bareudp0 -2) Device creation with multiple proto mode enabled +2) Device creation with multiproto mode enabled -There are two ways to create a bareudp device for MPLS & IP with multiproto mode -enabled. +The multiproto mode allows bareudp tunnels to handle several protocols of the +same family. It is currently only available for IP and MPLS. This mode has to +be enabled explicitly with the "multiproto" flag. - a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype 0x8847 multiproto + a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype ipv4 multiproto - b) ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls + For an IPv4 tunnel the multiproto mode allows the tunnel to also handle + IPv6. + + b) ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls_uc multiproto + + For MPLS, the multiproto mode allows the tunnel to handle both unicast + and multicast MPLS packets. 3) Device Usage diff --git a/Documentation/networking/can_ucan_protocol.rst b/Documentation/networking/can_ucan_protocol.rst index 4cef88d24fc7..638ac1ee7914 100644 --- a/Documentation/networking/can_ucan_protocol.rst +++ b/Documentation/networking/can_ucan_protocol.rst @@ -144,7 +144,7 @@ UCAN_COMMAND_SET_BITTIMING *Host2Dev; mandatory* -Setup bittiming by sending the the structure +Setup bittiming by sending the structure ``ucan_ctl_payload_t.cmd_set_bittiming`` (see ``struct bittiming`` for details) @@ -232,7 +232,7 @@ UCAN_IN_TX_COMPLETE zero The CAN device has sent a message to the CAN bus. It answers with a -list of of tuples <echo-ids, flags>. +list of tuples <echo-ids, flags>. The echo-id identifies the frame from (echos the id from a previous UCAN_OUT_TX message). The flag indicates the result of the diff --git a/Documentation/networking/devlink/devlink-trap.rst b/Documentation/networking/devlink/devlink-trap.rst index 1e3f3ffee248..2014307fbe63 100644 --- a/Documentation/networking/devlink/devlink-trap.rst +++ b/Documentation/networking/devlink/devlink-trap.rst @@ -486,6 +486,10 @@ narrow. The description of these groups must be added to the following table: - Contains packet traps for packets that should be locally delivered after routing, but do not match more specific packet traps (e.g., ``ipv4_bgp``) + * - ``external_delivery`` + - Contains packet traps for packets that should be routed through an + external interface (e.g., management interface) that does not belong to + the same device (e.g., switch ASIC) as the ingress interface * - ``ipv6`` - Contains packet traps for various IPv6 control packets (e.g., Router Advertisements) diff --git a/Documentation/networking/dsa/dsa.rst b/Documentation/networking/dsa/dsa.rst index 563d56c6a25c..a8d15dd2b42b 100644 --- a/Documentation/networking/dsa/dsa.rst +++ b/Documentation/networking/dsa/dsa.rst @@ -95,7 +95,7 @@ Ethernet switch. Networking stack hooks ---------------------- -When a master netdev is used with DSA, a small hook is placed in in the +When a master netdev is used with DSA, a small hook is placed in the networking stack is in order to have the DSA subsystem process the Ethernet switch specific tagging protocol. DSA accomplishes this by registering a specific (and fake) Ethernet type (later becoming ``skb->protocol``) with the diff --git a/Documentation/networking/ip-sysctl.rst b/Documentation/networking/ip-sysctl.rst index b72f89d5694c..837d51f9e1fa 100644 --- a/Documentation/networking/ip-sysctl.rst +++ b/Documentation/networking/ip-sysctl.rst @@ -741,7 +741,7 @@ tcp_fastopen - INTEGER Default: 0x1 - Note that that additional client or server features are only + Note that additional client or server features are only effective if the basic support (0x1 and 0x2) are enabled respectively. tcp_fastopen_blackhole_timeout_sec - INTEGER diff --git a/Documentation/networking/ipvs-sysctl.rst b/Documentation/networking/ipvs-sysctl.rst index be36c4600e8f..2afccc63856e 100644 --- a/Documentation/networking/ipvs-sysctl.rst +++ b/Documentation/networking/ipvs-sysctl.rst @@ -114,7 +114,7 @@ drop_entry - INTEGER modes (when there is no enough available memory, the strategy is enabled and the variable is automatically set to 2, otherwise the strategy is disabled and the variable is set to - 1), and 3 means that that the strategy is always enabled. + 1), and 3 means that the strategy is always enabled. drop_packet - INTEGER - 0 - disabled (default) diff --git a/Documentation/networking/rxrpc.rst b/Documentation/networking/rxrpc.rst index 68552b92dc44..39c2249c7aa7 100644 --- a/Documentation/networking/rxrpc.rst +++ b/Documentation/networking/rxrpc.rst @@ -186,7 +186,7 @@ About the AF_RXRPC driver: time [tunable] after the last connection using it discarded, in case a new connection is made that could use it. - (#) A client-side connection is only shared between calls if they have have + (#) A client-side connection is only shared between calls if they have the same key struct describing their security (and assuming the calls would otherwise share the connection). Non-secured calls would also be able to share connections with each other. |