diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/net/mediatek-net.txt | 2 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/phy.txt | 5 | ||||
| -rw-r--r-- | Documentation/filesystems/proc.txt | 5 | ||||
| -rw-r--r-- | Documentation/power/states.txt | 4 |
4 files changed, 8 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt index c010fafc66a8..c7194e87d5f4 100644 --- a/Documentation/devicetree/bindings/net/mediatek-net.txt +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -7,7 +7,7 @@ have dual GMAC each represented by a child node.. * Ethernet controller node Required properties: -- compatible: Should be "mediatek,mt7623-eth" +- compatible: Should be "mediatek,mt2701-eth" - reg: Address and length of the register set for the device - interrupts: Should contain the three frame engines interrupts in numeric order. These are fe_int0, fe_int1 and fe_int2. diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index ff1bc4b1bb3b..fb5056b22685 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -19,8 +19,9 @@ Optional Properties: specifications. If neither of these are specified, the default is to assume clause 22. - If the phy's identifier is known then the list may contain an entry - of the form: "ethernet-phy-idAAAA.BBBB" where + If the PHY reports an incorrect ID (or none at all) then the + "compatible" list may contain an entry with the correct PHY ID in the + form: "ethernet-phy-idAAAA.BBBB" where AAAA - The value of the 16 bit Phy Identifier 1 register as 4 hex digits. This is the chip vendor OUI bits 3:18 BBBB - The value of the 16 bit Phy Identifier 2 register as diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt index 72624a16b792..c94b4675d021 100644 --- a/Documentation/filesystems/proc.txt +++ b/Documentation/filesystems/proc.txt @@ -212,10 +212,11 @@ asynchronous manner and the value may not be very precise. To see a precise snapshot of a moment, you can see /proc/<pid>/smaps file and scan page table. It's slow but very precise. -Table 1-2: Contents of the status files (as of 4.1) +Table 1-2: Contents of the status files (as of 4.8) .............................................................................. Field Content Name filename of the executable + Umask file mode creation mask State state (R is running, S is sleeping, D is sleeping in an uninterruptible wait, Z is zombie, T is traced or stopped) @@ -226,7 +227,6 @@ Table 1-2: Contents of the status files (as of 4.1) TracerPid PID of process tracing this process (0 if not) Uid Real, effective, saved set, and file system UIDs Gid Real, effective, saved set, and file system GIDs - Umask file mode creation mask FDSize number of file descriptor slots currently allocated Groups supplementary group list NStgid descendant namespace thread group ID hierarchy @@ -236,6 +236,7 @@ Table 1-2: Contents of the status files (as of 4.1) VmPeak peak virtual memory size VmSize total program size VmLck locked memory size + VmPin pinned memory size VmHWM peak resident set size ("high water mark") VmRSS size of memory portions. It contains the three following parts (VmRSS = RssAnon + RssFile + RssShmem) diff --git a/Documentation/power/states.txt b/Documentation/power/states.txt index 8a39ce45d8a0..008ecb588317 100644 --- a/Documentation/power/states.txt +++ b/Documentation/power/states.txt @@ -35,9 +35,7 @@ only one way to cause the system to go into the Suspend-To-RAM state (write The default suspend mode (ie. the one to be used without writing anything into /sys/power/mem_sleep) is either "deep" (if Suspend-To-RAM is supported) or "s2idle", but it can be overridden by the value of the "mem_sleep_default" -parameter in the kernel command line. On some ACPI-based systems, depending on -the information in the FADT, the default may be "s2idle" even if Suspend-To-RAM -is supported. +parameter in the kernel command line. The properties of all of the sleep states are described below. |