diff options
Diffstat (limited to 'Documentation')
7 files changed, 75 insertions, 6 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index 2e3f919485f4..6a5f34b4d5b9 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -32,7 +32,7 @@ Description: Description of the physical chip / device for device X. Typically a part number. -What: /sys/bus/iio/devices/iio:deviceX/timestamp_clock +What: /sys/bus/iio/devices/iio:deviceX/current_timestamp_clock KernelVersion: 4.5 Contact: linux-iio@vger.kernel.org Description: @@ -1290,7 +1290,7 @@ KernelVersion: 3.4 Contact: linux-iio@vger.kernel.org Description: Unit-less light intensity. Modifiers both and ir indicate - that measurements contains visible and infrared light + that measurements contain visible and infrared light components or just infrared light, respectively. Modifier uv indicates that measurements contain ultraviolet light components. @@ -1413,6 +1413,16 @@ Description: the available samples after the timeout expires and thus have a maximum delay guarantee. +What: /sys/bus/iio/devices/iio:deviceX/buffer/data_available +KernelVersion: 4.16 +Contact: linux-iio@vger.kernel.org +Description: + A read-only value indicating the bytes of data available in the + buffer. In the case of an output buffer, this indicates the + amount of empty space available to write data to. In the case of + an input buffer, this indicates the amount of data available for + reading. + What: /sys/bus/iio/devices/iio:deviceX/buffer/hwfifo_enabled KernelVersion: 4.2 Contact: linux-iio@vger.kernel.org diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt index f413e82c8b83..1e6ee3deb4fa 100644 --- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -15,7 +15,6 @@ Required properties: - "clkin" for the reference clock (typically XTAL) - "core" for the SAR ADC core clock optional clocks: - - "sana" for the analog clock - "adc_clk" for the ADC (sampling) clock - "adc_sel" for the ADC (sampling) clock mux - vref-supply: the regulator supply for the ADC reference voltage diff --git a/Documentation/devicetree/bindings/iio/adc/aspeed_adc.txt b/Documentation/devicetree/bindings/iio/adc/aspeed_adc.txt index 674e133b7cd7..034fc2ba100e 100644 --- a/Documentation/devicetree/bindings/iio/adc/aspeed_adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/aspeed_adc.txt @@ -8,6 +8,7 @@ Required properties: - reg: memory window mapping address and length - clocks: Input clock used to derive the sample clock. Expected to be the SoC's APB clock. +- resets: Reset controller phandle - #io-channel-cells: Must be set to <1> to indicate channels are selected by index. @@ -15,6 +16,7 @@ Example: adc@1e6e9000 { compatible = "aspeed,ast2400-adc"; reg = <0x1e6e9000 0xb0>; - clocks = <&clk_apb>; + clocks = <&syscon ASPEED_CLK_APB>; + resets = <&syscon ASPEED_RESET_ADC>; #io-channel-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt index 552e7a83951d..6469a4cd2a6d 100644 --- a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt @@ -17,6 +17,11 @@ Required properties: This property uses the IRQ edge types values: IRQ_TYPE_EDGE_RISING , IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_BOTH +Optional properties: + - dmas: Phandle to dma channel for the ADC. + - dma-names: Must be "rx" when dmas property is being used. + See ../../dma/dma.txt for details. + Example: adc: adc@fc030000 { @@ -31,4 +36,6 @@ adc: adc@fc030000 { vddana-supply = <&vdd_3v3_lp_reg>; vref-supply = <&vdd_3v3_lp_reg>; atmel,trigger-edge-type = <IRQ_TYPE_EDGE_BOTH>; + dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(25))>; + dma-names = "rx"; } diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt index 48bfcaa3ffcd..e8bb8243e92c 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -62,6 +62,15 @@ Required properties: - st,adc-channels: List of single-ended channels muxed for this ADC. It can have up to 16 channels on stm32f4 or 20 channels on stm32h7, numbered from 0 to 15 or 19 (resp. for in0..in15 or in0..in19). +- st,adc-diff-channels: List of differential channels muxed for this ADC. + Depending on part used, some channels can be configured as differential + instead of single-ended (e.g. stm32h7). List here positive and negative + inputs pairs as <vinp vinn>, <vinp vinn>,... vinp and vinn are numbered + from 0 to 19 on stm32h7) + Note: At least one of "st,adc-channels" or "st,adc-diff-channels" is required. + Both properties can be used together. Some channels can be used as + single-ended and some other ones as differential (mixed). But channels + can't be configured both as single-ended and differential (invalid). - #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in Documentation/devicetree/bindings/iio/iio-bindings.txt @@ -111,3 +120,18 @@ Example: ... other adc child nodes follow... }; + +Example to setup: +- channel 1 as single-ended +- channels 2 & 3 as differential (with resp. 6 & 7 negative inputs) + + adc: adc@40022000 { + compatible = "st,stm32h7-adc-core"; + ... + adc1: adc@0 { + compatible = "st,stm32h7-adc"; + ... + st,adc-channels = <1>; + st,adc-diff-channels = <2 6>, <3 7>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/health/max30102.txt b/Documentation/devicetree/bindings/iio/health/max30102.txt index 8629c18b0e78..ef2ca0a0306f 100644 --- a/Documentation/devicetree/bindings/iio/health/max30102.txt +++ b/Documentation/devicetree/bindings/iio/health/max30102.txt @@ -1,9 +1,11 @@ Maxim MAX30102 heart rate and pulse oximeter sensor +Maxim MAX30105 optical particle-sensing module * https://datasheets.maximintegrated.com/en/ds/MAX30102.pdf +* https://datasheets.maximintegrated.com/en/ds/MAX30105.pdf Required properties: - - compatible: must be "maxim,max30102" + - compatible: must be "maxim,max30102" or "maxim,max30105" - reg: the I2C address of the sensor - interrupt-parent: should be the phandle for the interrupt controller - interrupts: the sole interrupt generated by the device @@ -12,8 +14,10 @@ Required properties: interrupt client node bindings. Optional properties: - - maxim,red-led-current-microamp: configuration for RED LED current + - maxim,red-led-current-microamp: configuration for red LED current - maxim,ir-led-current-microamp: configuration for IR LED current + - maxim,green-led-current-microamp: configuration for green LED current + (max30105 only) Note that each step is approximately 200 microamps, ranging from 0 uA to 50800 uA. diff --git a/Documentation/devicetree/bindings/iio/light/uvis25.txt b/Documentation/devicetree/bindings/iio/light/uvis25.txt new file mode 100644 index 000000000000..3041207e3f3c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/uvis25.txt @@ -0,0 +1,23 @@ +* ST UVIS25 uv sensor + +Required properties: +- compatible: should be "st,uvis25" +- reg: i2c address of the sensor / spi cs line + +Optional properties: +- interrupt-parent: should be the phandle for the interrupt controller +- interrupts: interrupt mapping for IRQ. It should be configured with + flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or + IRQ_TYPE_EDGE_FALLING. + + Refer to interrupt-controller/interrupts.txt for generic interrupt + client node bindings. + +Example: + +uvis25@47 { + compatible = "st,uvis25"; + reg = <0x47>; + interrupt-parent = <&gpio0>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; +}; |