diff options
Diffstat (limited to 'Documentation')
34 files changed, 1384 insertions, 304 deletions
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 7f40cb5f490b..061f7b98a07f 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -110,6 +110,7 @@ Board compatible values (alphabetically, grouped by SoC): - "amlogic,u200" (Meson g12a s905d2) - "amediatech,x96-max" (Meson g12a s905x2) + - "seirobotics,sei510" (Meson g12a s905x2) Amlogic Meson Firmware registers Interface ------------------------------------------ diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt index 72d481c8dd48..5d7dbabbb784 100644 --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt @@ -22,9 +22,11 @@ Required properties: ------------------- - compatible: should be "fsl,imx-scu". - mbox-names: should include "tx0", "tx1", "tx2", "tx3", - "rx0", "rx1", "rx2", "rx3". -- mboxes: List of phandle of 4 MU channels for tx and 4 MU channels - for rx. All 8 MU channels must be in the same MU instance. + "rx0", "rx1", "rx2", "rx3"; + include "gip3" if want to support general MU interrupt. +- mboxes: List of phandle of 4 MU channels for tx, 4 MU channels for + rx, and 1 optional MU channel for general interrupt. + All MU channels must be in the same MU instance. Cross instances are not allowed. The MU instance can only be one of LSIO MU0~M4 for imx8qxp and imx8qm. Users need to make sure use the one which is not conflict with other @@ -34,6 +36,7 @@ Required properties: Channel 1 must be "tx1" or "rx1". Channel 2 must be "tx2" or "rx2". Channel 3 must be "tx3" or "rx3". + General interrupt rx channel must be "gip3". e.g. mboxes = <&lsio_mu1 0 0 &lsio_mu1 0 1 @@ -42,10 +45,18 @@ Required properties: &lsio_mu1 1 0 &lsio_mu1 1 1 &lsio_mu1 1 2 - &lsio_mu1 1 3>; + &lsio_mu1 1 3 + &lsio_mu1 3 3>; See Documentation/devicetree/bindings/mailbox/fsl,mu.txt for detailed mailbox binding. +Note: Each mu which supports general interrupt should have an alias correctly +numbered in "aliases" node. +e.g. +aliases { + mu1 = &lsio_mu1; +}; + i.MX SCU Client Device Node: ============================================================ @@ -124,6 +135,10 @@ Required properties: Example (imx8qxp): ------------- +aliases { + mu1 = &lsio_mu1; +}; + lsio_mu1: mailbox@5d1c0000 { ... #mbox-cells = <2>; @@ -133,7 +148,8 @@ firmware { scu { compatible = "fsl,imx-scu"; mbox-names = "tx0", "tx1", "tx2", "tx3", - "rx0", "rx1", "rx2", "rx3"; + "rx0", "rx1", "rx2", "rx3", + "gip3"; mboxes = <&lsio_mu1 0 0 &lsio_mu1 0 1 &lsio_mu1 0 2 @@ -141,7 +157,8 @@ firmware { &lsio_mu1 1 0 &lsio_mu1 1 1 &lsio_mu1 1 2 - &lsio_mu1 1 3>; + &lsio_mu1 1 3 + &lsio_mu1 3 3>; clk: clk { compatible = "fsl,imx8qxp-clk", "fsl,scu-clk"; diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 7e2cd6ad26bd..407138ebc0d0 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -51,6 +51,13 @@ properties: - const: i2se,duckbill-2 - const: fsl,imx28 + - description: i.MX50 based Boards + items: + - enum: + - fsl,imx50-evk + - kobo,aura + - const: fsl,imx50 + - description: i.MX51 Babbage Board items: - enum: @@ -67,6 +74,7 @@ properties: - fsl,imx53-evk - fsl,imx53-qsb - fsl,imx53-smd + - menlo,m53menlo - const: fsl,imx53 - description: i.MX6Q based Boards @@ -90,6 +98,7 @@ properties: - description: i.MX6DL based Boards items: - enum: + - eckelmann,imx6dl-ci4x10 - fsl,imx6dl-sabreauto # i.MX6 DualLite/Solo SABRE Automotive Board - fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board - technologic,imx6dl-ts4900 @@ -137,10 +146,18 @@ properties: - const: fsl,imx6ull # This seems odd. Should be last? - const: fsl,imx6ulz + - description: i.MX7S based Boards + items: + - enum: + - tq,imx7s-mba7 # i.MX7S TQ MBa7 with TQMa7S SoM + - const: fsl,imx7s + - description: i.MX7D based Boards items: - enum: - fsl,imx7d-sdb # i.MX7 SabreSD Board + - tq,imx7d-mba7 # i.MX7D TQ MBa7 with TQMa7D SoM + - zii,imx7d-rpu2 # ZII RPU2 Board - const: fsl,imx7d - description: @@ -154,6 +171,12 @@ properties: - const: compulab,cl-som-imx7 - const: fsl,imx7d + - description: i.MX8MM based Boards + items: + - enum: + - fsl,imx8mm-evk # i.MX8MM EVK Board + - const: fsl,imx8mm + - description: i.MX8QXP based Boards items: - enum: @@ -176,6 +199,19 @@ properties: - fsl,vf610 - fsl,vf610m4 + - description: ZII's VF610 based Boards + items: + - enum: + - zii,vf610cfu1 # ZII VF610 CFU1 Board + - zii,vf610dev-c # ZII VF610 Development Board, Rev C + - zii,vf610dev-b # ZII VF610 Development Board, Rev B + - zii,vf610scu4-aib # ZII VF610 SCU4 AIB + - zii,vf610dtu # ZII VF610 SSMB DTU Board + - zii,vf610spu3 # ZII VF610 SSMB SPU3 Board + - zii,vf610spb4 # ZII VF610 SPB4 Board + - const: zii,vf610dev + - const: fsl,vf610 + - description: LS1012A based Boards items: - enum: diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 2ecc712bf707..1c1e48fd94b5 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -92,6 +92,9 @@ SoCs: - DRA718 compatible = "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7" +- AM5748 + compatible = "ti,am5748", "ti,dra762", "ti,dra7" + - AM5728 compatible = "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" @@ -184,6 +187,9 @@ Boards: - AM57XX SBC-AM57x compatible = "compulab,sbc-am57x", "compulab,cl-som-am57x", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" +- AM5748 IDK + compatible = "ti,am5748-idk", "ti,am5748", "ti,dra762", "ti,dra7"; + - AM5728 IDK compatible = "ti,am5728-idk", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml index 061a03edf9c8..5c6bbf10abc9 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.yaml +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml @@ -97,6 +97,7 @@ properties: - enum: - friendlyarm,nanopc-t4 - friendlyarm,nanopi-m4 + - friendlyarm,nanopi-neo4 - const: rockchip,rk3399 - description: GeekBuying GeekBox @@ -146,7 +147,7 @@ properties: - const: google,gru - const: rockchip,rk3399 - - description: Google Jaq (Haier Chromebook 11 and more) + - description: Google Jaq (Haier Chromebook 11 and more w/ uSD) items: - const: google,veyron-jaq-rev5 - const: google,veyron-jaq-rev4 @@ -159,6 +160,12 @@ properties: - description: Google Jerry (Hisense Chromebook C11 and more) items: + - const: google,veyron-jerry-rev15 + - const: google,veyron-jerry-rev14 + - const: google,veyron-jerry-rev13 + - const: google,veyron-jerry-rev12 + - const: google,veyron-jerry-rev11 + - const: google,veyron-jerry-rev10 - const: google,veyron-jerry-rev7 - const: google,veyron-jerry-rev6 - const: google,veyron-jerry-rev5 @@ -199,6 +206,17 @@ properties: - const: google,veyron - const: rockchip,rk3288 + - description: Google Mighty (Haier Chromebook 11 and more w/ SD) + items: + - const: google,veyron-mighty-rev5 + - const: google,veyron-mighty-rev4 + - const: google,veyron-mighty-rev3 + - const: google,veyron-mighty-rev2 + - const: google,veyron-mighty-rev1 + - const: google,veyron-mighty + - const: google,veyron + - const: rockchip,rk3288 + - description: Google Minnie (Asus Chromebook Flip C100P) items: - const: google,veyron-minnie-rev4 @@ -308,6 +326,11 @@ properties: - const: netxeon,r89 - const: rockchip,rk3288 + - description: Orange Pi RK3399 board + items: + - const: rockchip,rk3399-orangepi + - const: rockchip,rk3399 + - description: Phytec phyCORE-RK3288 Rapid Development Kit items: - const: phytec,rk3288-pcm-947 diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt deleted file mode 100644 index 9254cbe7d516..000000000000 --- a/Documentation/devicetree/bindings/arm/sunxi.txt +++ /dev/null @@ -1,23 +0,0 @@ -Allwinner sunXi Platforms Device Tree Bindings - -Each device tree must specify which Allwinner SoC it uses, -using one of the following compatible strings: - - allwinner,sun4i-a10 - allwinner,sun5i-a10s - allwinner,sun5i-a13 - allwinner,sun5i-r8 - allwinner,sun6i-a31 - allwinner,sun7i-a20 - allwinner,sun8i-a23 - allwinner,sun8i-a33 - allwinner,sun8i-a83t - allwinner,sun8i-h2-plus - allwinner,sun8i-h3 - allwinner,sun8i-r40 - allwinner,sun8i-t3 - allwinner,sun8i-v3s - allwinner,sun9i-a80 - allwinner,sun50i-a64 - allwinner,suniv-f1c100s - nextthing,gr8 diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml new file mode 100644 index 000000000000..285f4fc8519d --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -0,0 +1,807 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR X11) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/sunxi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner platforms device tree bindings + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + $nodename: + const: '/' + compatible: + oneOf: + + - description: Allwinner A23 Evaluation Board + items: + - const: allwinner,sun8i-a23-evb + - const: allwinner,sun8i-a23 + + - description: Allwinner A31 APP4 Evaluation Board + items: + - const: allwinner,app4-evb1 + - const: allwinner,sun6i-a31 + + - description: Allwinner A83t Homlet Evaluation Board v2 + items: + - const: allwinner,h8homlet-v2 + - const: allwinner,sun8i-a83t + + - description: Allwinner GA10H Quad Core Tablet v1.1 + items: + - const: allwinner,ga10h-v1.1 + - const: allwinner,sun8i-a33 + + - description: Allwinner GT90H Tablet v4 + items: + - const: allwinner,gt90h-v4 + - const: allwinner,sun8i-a23 + + - description: Allwinner R16 EVB (Parrot) + items: + - const: allwinner,parrot + - const: allwinner,sun8i-a33 + + - description: Amarula A64 Relic + items: + - const: amarula,a64-relic + - const: allwinner,sun50i-a64 + + - description: Auxtek T003 A10s HDMI TV Stick + items: + - const: allwinner,auxtek-t003 + - const: allwinner,sun5i-a10s + + - description: Auxtek T004 A10s HDMI TV Stick + items: + - const: allwinner,auxtek-t004 + - const: allwinner,sun5i-a10s + + - description: BA10 TV Box + items: + - const: allwinner,ba10-tvbox + - const: allwinner,sun4i-a10 + + - description: BananaPi + items: + - const: lemaker,bananapi + - const: allwinner,sun7i-a20 + + - description: BananaPi M1 Plus + items: + - const: sinovoip,bpi-m1-plus + - const: allwinner,sun7i-a20 + + - description: BananaPi M2 + items: + - const: sinovoip,bpi-m2 + - const: allwinner,sun6i-a31s + + - description: BananaPi M2 Berry + items: + - const: sinovoip,bpi-m2-berry + - const: allwinner,sun8i-r40 + + - description: BananaPi M2 Plus + items: + - const: sinovoip,bpi-m2-plus + - const: allwinner,sun8i-h3 + + - description: BananaPi M2 Plus + items: + - const: sinovoip,bpi-m2-plus + - const: allwinner,sun50i-h5 + + - description: BananaPi M2 Plus v1.2 + items: + - const: bananapi,bpi-m2-plus-v1.2 + - const: allwinner,sun8i-h3 + + - description: BananaPi M2 Plus v1.2 + items: + - const: bananapi,bpi-m2-plus-v1.2 + - const: allwinner,sun50i-h5 + + - description: BananaPi M2 Magic + items: + - const: sinovoip,bananapi-m2m + - const: allwinner,sun8i-a33 + + - description: BananaPi M2 Ultra + items: + - const: sinovoip,bpi-m2-ultra + - const: allwinner,sun8i-r40 + + - description: BananaPi M2 Zero + items: + - const: sinovoip,bpi-m2-zero + - const: allwinner,sun8i-h2-plus + + - description: BananaPi M3 + items: + - const: sinovoip,bpi-m3 + - const: allwinner,sun8i-a83t + + - description: BananaPi M64 + items: + - const: sinovoip,bananapi-m64 + - const: allwinner,sun50i-a64 + + - description: BananaPro + items: + - const: lemaker,bananapro + - const: allwinner,sun7i-a20 + + - description: Beelink GS1 + items: + - const: azw,beelink-gs1 + - const: allwinner,sun50i-h6 + + - description: Beelink X2 + items: + - const: roofull,beelink-x2 + - const: allwinner,sun8i-h3 + + - description: Chuwi V7 CW0825 + items: + - const: chuwi,v7-cw0825 + - const: allwinner,sun4i-a10 + + - description: Colorfly E708 Q1 Tablet + items: + - const: colorfly,e708-q1 + - const: allwinner,sun6i-a31s + + - description: CSQ CS908 Set Top Box + items: + - const: csq,cs908 + - const: allwinner,sun6i-a31s + + - description: Cubietech Cubieboard + items: + - const: cubietech,a10-cubieboard + - const: allwinner,sun4i-a10 + + - description: Cubietech Cubieboard2 + items: + - const: cubietech,cubieboard2 + - const: allwinner,sun7i-a20 + + - description: Cubietech Cubieboard4 + items: + - const: cubietech,a80-cubieboard4 + - const: allwinner,sun9i-a80 + + - description: Cubietech Cubietruck + items: + - const: cubietech,cubietruck + - const: allwinner,sun7i-a20 + + - description: Cubietech Cubietruck Plus + items: + - const: cubietech,cubietruck-plus + - const: allwinner,sun8i-a83t + + - description: Difrnce DIT4350 + items: + - const: difrnce,dit4350 + - const: allwinner,sun5i-a13 + + - description: Dserve DSRV9703C + items: + - const: dserve,dsrv9703c + - const: allwinner,sun4i-a10 + + - description: Empire Electronix D709 Tablet + items: + - const: empire-electronix,d709 + - const: allwinner,sun5i-a13 + + - description: Empire Electronix M712 Tablet + items: + - const: empire-electronix,m712 + - const: allwinner,sun5i-a13 + + - description: FriendlyARM NanoPi A64 + items: + - const: friendlyarm,nanopi-a64 + - const: allwinner,sun50i-a64 + + - description: FriendlyARM NanoPi M1 + items: + - const: friendlyarm,nanopi-m1 + - const: allwinner,sun8i-h3 + + - description: FriendlyARM NanoPi M1 Plus + items: + - const: friendlyarm,nanopi-m1-plus + - const: allwinner,sun8i-h3 + + - description: FriendlyARM NanoPi Neo + items: + - const: friendlyarm,nanopi-neo + - const: allwinner,sun8i-h3 + + - description: FriendlyARM NanoPi Neo 2 + items: + - const: friendlyarm,nanopi-neo2 + - const: allwinner,sun50i-h5 + + - description: FriendlyARM NanoPi Neo Air + items: + - const: friendlyarm,nanopi-neo-air + - const: allwinner,sun8i-h3 + + - description: FriendlyARM NanoPi Neo Plus2 + items: + - const: friendlyarm,nanopi-neo-plus2 + - const: allwinner,sun50i-h5 + + - description: Gemei G9 Tablet + items: + - const: gemei,g9 + - const: allwinner,sun4i-a10 + + - description: Hyundai A7HD + items: + - const: hyundai,a7hd + - const: allwinner,sun4i-a10 + + - description: HSG H702 + items: + - const: hsg,h702 + - const: allwinner,sun5i-a13 + + - description: I12 TV Box + items: + - const: allwinner,i12-tvbox + - const: allwinner,sun7i-a20 + + - description: ICNova A20 SWAC + items: + - const: swac,icnova-a20-swac + - const: incircuit,icnova-a20 + - const: allwinner,sun7i-a20 + + - description: INet-1 + items: + - const: inet-tek,inet1 + - const: allwinner,sun4i-a10 + + - description: iNet-86DZ Rev 01 + items: + - const: primux,inet86dz + - const: allwinner,sun8i-a23 + + - description: iNet-9F Rev 03 + items: + - const: inet-tek,inet9f-rev03 + - const: allwinner,sun4i-a10 + + - description: iNet-97F Rev 02 + items: + - const: primux,inet97fv2 + - const: allwinner,sun4i-a10 + + - description: iNet-98V Rev 02 + items: + - const: primux,inet98v-rev2 + - const: allwinner,sun5i-a13 + + - description: iNet D978 Rev 02 Tablet + items: + - const: primux,inet-d978-rev2 + - const: allwinner,sun8i-a33 + + - description: iNet Q972 Tablet + items: + - const: inet-tek,inet-q972 + - const: allwinner,sun6i-a31s + + - description: Itead Ibox A20 + items: + - const: itead,itead-ibox-a20 + - const: allwinner,sun7i-a20 + + - description: Itead Iteaduino Plus A10 + items: + - const: itead,iteaduino-plus-a10 + - const: allwinner,sun4i-a10 + + - description: Jesurun Q5 + items: + - const: jesurun,q5 + - const: allwinner,sun4i-a10 + + - description: Lamobo R1 + items: + - const: lamobo,lamobo-r1 + - const: allwinner,sun7i-a20 + + - description: Libre Computer Board ALL-H3-CC H2+ + items: + - const: libretech,all-h3-cc-h2-plus + - const: allwinner,sun8i-h2-plus + + - description: Libre Computer Board ALL-H3-CC H3 + items: + - const: libretech,all-h3-cc-h3 + - const: allwinner,sun8i-h3 + + - description: Libre Computer Board ALL-H3-CC H5 + items: + - const: libretech,all-h3-cc-h5 + - const: allwinner,sun50i-h5 + + - description: Lichee Pi One + items: + - const: licheepi,licheepi-one + - const: allwinner,sun5i-a13 + + - description: Lichee Pi Zero + items: + - const: licheepi,licheepi-zero + - const: allwinner,sun8i-v3s + + - description: Lichee Pi Zero (with Dock) + items: + - const: licheepi,licheepi-zero-dock + - const: licheepi,licheepi-zero + - const: allwinner,sun8i-v3s + + - description: Linksprite PCDuino + items: + - const: linksprite,a10-pcduino + - const: allwinner,sun4i-a10 + + - description: Linksprite PCDuino2 + items: + - const: linksprite,a10-pcduino2 + - const: allwinner,sun4i-a10 + + - description: Linksprite PCDuino3 + items: + - const: linksprite,pcduino3 + - const: allwinner,sun7i-a20 + + - description: Linksprite PCDuino3 Nano + items: + - const: linksprite,pcduino3-nano + - const: allwinner,sun7i-a20 + + - description: HAOYU Electronics Marsboard A10 + items: + - const: haoyu,a10-marsboard + - const: allwinner,sun4i-a10 + + - description: MapleBoard MP130 + items: + - const: mapleboard,mp130 + - const: allwinner,sun8i-h3 + + - description: Mele A1000 + items: + - const: mele,a1000 + - const: allwinner,sun4i-a10 + + - description: Mele A1000G Quad Set Top Box + items: + - const: mele,a1000g-quad + - const: allwinner,sun6i-a31 + + - description: Mele I7 Quad Set Top Box + items: + - const: mele,i7 + - const: allwinner,sun6i-a31 + + - description: Mele M3 + items: + - const: mele,m3 + - const: allwinner,sun7i-a20 + + - description: Mele M9 Set Top Box + items: + - const: mele,m9 + - const: allwinner,sun6i-a31 + + - description: Merrii A20 Hummingboard + items: + - const: merrii,a20-hummingbird + - const: allwinner,sun7i-a20 + + - description: Merrii A31 Hummingboard + items: + - const: merrii,a31-hummingbird + - const: allwinner,sun6i-a31 + + - description: Merrii A80 Optimus + items: + - const: merrii,a80-optimus + - const: allwinner,sun9i-a80 + + - description: Miniand Hackberry + items: + - const: miniand,hackberry + - const: allwinner,sun4i-a10 + + - description: MK802 + items: + - const: allwinner,mk802 + - const: allwinner,sun4i-a10 + + - description: MK802-A10s + items: + - const: allwinner,a10s-mk802 + - const: allwinner,sun5i-a10s + + - description: MK802-II + items: + - const: allwinner,mk802ii + - const: allwinner,sun4i-a10 + + - description: MK808c + items: + - const: allwinner,mk808c + - const: allwinner,sun7i-a20 + + - description: MSI Primo81 Tablet + items: + - const: msi,primo81 + - const: allwinner,sun6i-a31s + + - description: Emlid Neutis N5 Developper Board + items: + - const: emlid,neutis-n5-devboard + - const: emlid,neutis-n5 + - const: allwinner,sun50i-h5 + + - description: NextThing Co. CHIP + items: + - const: nextthing,chip + - const: allwinner,sun5i-r8 + - const: allwinner,sun5i-a13 + + - description: NextThing Co. CHIP Pro + items: + - const: nextthing,chip-pro + - const: nextthing,gr8 + + - description: NextThing Co. GR8 Evaluation Board + items: + - const: nextthing,gr8-evb + - const: nextthing,gr8 + + - description: Nintendo NES Classic + items: + - const: nintendo,nes-classic + - const: allwinner,sun8i-r16 + - const: allwinner,sun8i-a33 + + - description: Nintendo Super NES Classic + items: + - const: nintendo,super-nes-classic + - const: nintendo,nes-classic + - const: allwinner,sun8i-r16 + - const: allwinner,sun8i-a33 + + - description: Oceanic 5inMFD (5205) + items: + - const: oceanic,5205-5inmfd + - const: allwinner,sun50i-a64 + + - description: Olimex A10-OlinuXino LIME + items: + - const: olimex,a10-olinuxino-lime + - const: allwinner,sun4i-a10 + + - description: Olimex A10s-OlinuXino Micro + items: + - const: olimex,a10s-olinuxino-micro + - const: allwinner,sun5i-a10s + + - description: Olimex A13-OlinuXino + items: + - const: olimex,a13-olinuxino + - const: allwinner,sun5i-a13 + + - description: Olimex A13-OlinuXino Micro + items: + - const: olimex,a13-olinuxino-micro + - const: allwinner,sun5i-a13 + + - description: Olimex A20-Olimex SOM Evaluation Board + items: + - const: olimex,a20-olimex-som-evb + - const: allwinner,sun7i-a20 + + - description: Olimex A20-Olimex SOM Evaluation Board (with eMMC) + items: + - const: olimex,a20-olimex-som-evb-emmc + - const: allwinner,sun7i-a20 + + - description: Olimex A20-OlinuXino LIME + items: + - const: olimex,a20-olinuxino-lime + - const: allwinner,sun7i-a20 + + - description: Olimex A20-OlinuXino LIME2 + items: + - const: olimex,a20-olinuxino-lime2 + - const: allwinner,sun7i-a20 + + - description: Olimex A20-OlinuXino LIME2 (with eMMC) + items: + - const: olimex,a20-olinuxino-lime2-emmc + - const: allwinner,sun7i-a20 + + - description: Olimex A20-OlinuXino Micro + items: + - const: olimex,a20-olinuxino-micro + - const: allwinner,sun7i-a20 + + - description: Olimex A20-OlinuXino Micro (with eMMC) + items: + - const: olimex,a20-olinuxino-micro-emmc + - const: allwinner,sun7i-a20 + + - description: Olimex A20-SOM204 Evaluation Board + items: + - const: olimex,a20-olimex-som204-evb + - const: allwinner,sun7i-a20 + + - description: Olimex A20-SOM204 Evaluation Board (with eMMC) + items: + - const: olimex,a20-olimex-som204-evb-emmc + - const: allwinner,sun7i-a20 + + - description: Olimex A33-OlinuXino + items: + - const: olimex,a33-olinuxino + - const: allwinner,sun8i-a33 + + - description: Olimex A64-OlinuXino + items: + - const: olimex,a64-olinuxino + - const: allwinner,sun50i-a64 + + - description: Olimex A64 Teres-I + items: + - const: olimex,a64-teres-i + - const: allwinner,sun50i-a64 + + - description: Pine64 + items: + - const: pine64,pine64 + - const: allwinner,sun50i-a64 + + - description: Pine64+ + items: + - const: pine64,pine64-plus + - const: allwinner,sun50i-a64 + + - description: Pine64 PineH64 + items: + - const: pine64,pine-h64 + - const: allwinner,sun50i-h6 + + - description: Pine64 LTS + items: + - const: pine64,pine64-lts + - const: allwinner,sun50i-r18 + - const: allwinner,sun50i-a64 + + - description: Pine64 Pinebook + items: + - const: pine64,pinebook + - const: allwinner,sun50i-a64 + + - description: Pine64 SoPine Baseboard + items: + - const: pine64,sopine-baseboard + - const: pine64,sopine + - const: allwinner,sun50i-a64 + + - description: PineRiver Mini X-Plus + items: + - const: pineriver,mini-xplus + - const: allwinner,sun4i-a10 + + - description: Point of View Protab2-IPS9 + items: + - const: pov,protab2-ips9 + - const: allwinner,sun4i-a10 + + - description: Polaroid MID2407PXE03 Tablet + items: + - const: polaroid,mid2407pxe03 + - const: allwinner,sun8i-a23 + + - description: Polaroid MID2809PXE04 Tablet + items: + - const: polaroid,mid2809pxe04 + - const: allwinner,sun8i-a23 + + - description: Q8 A13 Tablet + items: + - const: allwinner,q8-a13 + - const: allwinner,sun5i-a13 + + - description: Q8 A23 Tablet + items: + - const: allwinner,q8-a23 + - const: allwinner,sun8i-a23 + + - description: Q8 A33 Tablet + items: + - const: allwinner,q8-a33 + - const: allwinner,sun8i-a33 + + - description: Qihua CQA3T BV3 + items: + - const: qihua,t3-cqa3t-bv3 + - const: allwinner,sun8i-t3 + - const: allwinner,sun8i-r40 + + - description: R7 A10s HDMI TV Stick + items: + - const: allwinner,r7-tv-dongle + - const: allwinner,sun5i-a10s + + - description: RerVision H3-DVK + items: + - const: rervision,h3-dvk + - const: allwinner,sun8i-h3 + + - description: Sinlinx SinA31s Core Board + items: + - const: sinlinx,sina31s + - const: allwinner,sun6i-a31s + + - description: Sinlinx SinA31s Development Board + items: + - const: sinlinx,sina31s-sdk + - const: allwinner,sun6i-a31s + + - description: Sinlinx SinA33 + items: + - const: sinlinx,sina33 + - const: allwinner,sun8i-a33 + + - description: TBS A711 Tablet + items: + - const: tbs-biometrics,a711 + - const: allwinner,sun8i-a83t + + - description: Utoo P66 + items: + - const: utoo,p66 + - const: allwinner,sun5i-a13 + + - description: Wexler TAB7200 + items: + - const: wexler,tab7200 + - const: allwinner,sun7i-a20 + + - description: WITS A31 Colombus Evaluation Board + items: + - const: wits,colombus + - const: allwinner,sun6i-a31 + + - description: WITS Pro A20 DKT + items: + - const: wits,pro-a20-dkt + - const: allwinner,sun7i-a20 + + - description: Wobo i5 + items: + - const: wobo,a10s-wobo-i5 + - const: allwinner,sun5i-a10s + + - description: Yones TopTech BS1078 v2 Tablet + items: + - const: yones-toptech,bs1078-v2 + - const: allwinner,sun6i-a31s + + - description: Xunlong OrangePi + items: + - const: xunlong,orangepi + - const: allwinner,sun7i-a20 + + - description: Xunlong OrangePi 2 + items: + - const: xunlong,orangepi-2 + - const: allwinner,sun8i-h3 + + - description: Xunlong OrangePi 3 + items: + - const: xunlong,orangepi-3 + - const: allwinner,sun50i-h6 + + - description: Xunlong OrangePi Lite + items: + - const: xunlong,orangepi-lite + - const: allwinner,sun8i-h3 + + - description: Xunlong OrangePi Lite2 + items: + - const: xunlong,orangepi-lite2 + - const: allwinner,sun50i-h6 + + - description: Xunlong OrangePi Mini + items: + - const: xunlong,orangepi-mini + - const: allwinner,sun7i-a20 + + - description: Xunlong OrangePi One + items: + - const: xunlong,orangepi-one + - const: allwinner,sun8i-h3 + + - description: Xunlong OrangePi One Plus + items: + - const: xunlong,orangepi-one-plus + - const: allwinner,sun50i-h6 + + - description: Xunlong OrangePi PC + items: + - const: xunlong,orangepi-pc + - const: allwinner,sun8i-h3 + + - description: Xunlong OrangePi PC 2 + items: + - const: xunlong,orangepi-pc2 + - const: allwinner,sun50i-h5 + + - description: Xunlong OrangePi PC Plus + items: + - const: xunlong,orangepi-pc-plus + - const: allwinner,sun8i-h3 + + - description: Xunlong OrangePi Plus + items: + - const: xunlong,orangepi-plus + - const: allwinner,sun8i-h3 + + - description: Xunlong OrangePi Plus 2E + items: + - const: xunlong,orangepi-plus2e + - const: allwinner,sun8i-h3 + + - description: Xunlong OrangePi Prime + items: + - const: xunlong,orangepi-prime + - const: allwinner,sun50i-h5 + + - description: Xunlong OrangePi R1 + items: + - const: xunlong,orangepi-r1 + - const: allwinner,sun8i-h2-plus + + - description: Xunlong OrangePi Win + items: + - const: xunlong,orangepi-win + - const: allwinner,sun50i-a64 + + - description: Xunlong OrangePi Zero + items: + - const: xunlong,orangepi-zero + - const: allwinner,sun8i-h2-plus + + - description: Xunlong OrangePi Zero Plus + items: + - const: xunlong,orangepi-zero-plus + - const: allwinner,sun50i-h5 + + - description: Xunlong OrangePi Zero Plus2 + items: + - const: xunlong,orangepi-zero-plus2 + - const: allwinner,sun50i-h5 + + - description: Xunlong OrangePi Zero Plus2 + items: + - const: xunlong,orangepi-zero-plus2-h3 + - const: allwinner,sun8i-h3 diff --git a/Documentation/devicetree/bindings/bus/ti-sysc.txt b/Documentation/devicetree/bindings/bus/ti-sysc.txt index 85a23f551f02..233eb8294204 100644 --- a/Documentation/devicetree/bindings/bus/ti-sysc.txt +++ b/Documentation/devicetree/bindings/bus/ti-sysc.txt @@ -94,6 +94,8 @@ Optional properties: - ti,no-idle-on-init interconnect target module should not be idled at init +- ti,no-idle interconnect target module should not be idled + Example: Single instance of MUSB controller on omap4 using interconnect ranges using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000): @@ -131,6 +133,6 @@ using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000): }; }; -Note that other SoCs, such as am335x can have multipe child devices. On am335x +Note that other SoCs, such as am335x can have multiple child devices. On am335x there are two MUSB instances, two USB PHY instances, and a single CPPI41 DMA -instance as children of a single interconnet target module. +instance as children of a single interconnect target module. diff --git a/Documentation/devicetree/bindings/clock/xlnx,zynqmp-clk.txt b/Documentation/devicetree/bindings/clock/xlnx,zynqmp-clk.txt new file mode 100644 index 000000000000..391ee1a60bed --- /dev/null +++ b/Documentation/devicetree/bindings/clock/xlnx,zynqmp-clk.txt @@ -0,0 +1,63 @@ +-------------------------------------------------------------------------- +Device Tree Clock bindings for the Zynq Ultrascale+ MPSoC controlled using +Zynq MPSoC firmware interface +-------------------------------------------------------------------------- +The clock controller is a h/w block of Zynq Ultrascale+ MPSoC clock +tree. It reads required input clock frequencies from the devicetree and acts +as clock provider for all clock consumers of PS clocks. + +See clock_bindings.txt for more information on the generic clock bindings. + +Required properties: + - #clock-cells: Must be 1 + - compatible: Must contain: "xlnx,zynqmp-clk" + - clocks: List of clock specifiers which are external input + clocks to the given clock controller. Please refer + the next section to find the input clocks for a + given controller. + - clock-names: List of clock names which are exteral input clocks + to the given clock controller. Please refer to the + clock bindings for more details. + +Input clocks for zynqmp Ultrascale+ clock controller: + +The Zynq UltraScale+ MPSoC has one primary and four alternative reference clock +inputs. These required clock inputs are: + - pss_ref_clk (PS reference clock) + - video_clk (reference clock for video system ) + - pss_alt_ref_clk (alternative PS reference clock) + - aux_ref_clk + - gt_crx_ref_clk (transceiver reference clock) + +The following strings are optional parameters to the 'clock-names' property in +order to provide an optional (E)MIO clock source: + - swdt0_ext_clk + - swdt1_ext_clk + - gem0_emio_clk + - gem1_emio_clk + - gem2_emio_clk + - gem3_emio_clk + - mio_clk_XX # with XX = 00..77 + - mio_clk_50_or_51 #for the mux clock to gem tsu from 50 or 51 + + +Output clocks are registered based on clock information received +from firmware. Output clocks indexes are mentioned in +include/dt-bindings/clock/xlnx-zynqmp-clk.h. + +------- +Example +------- + +firmware { + zynqmp_firmware: zynqmp-firmware { + compatible = "xlnx,zynqmp-firmware"; + method = "smc"; + zynqmp_clk: clock-controller { + #clock-cells = <1>; + compatible = "xlnx,zynqmp-clk"; + clocks = <&pss_ref_clk>, <&video_clk>, <&pss_alt_ref_clk>, <&aux_ref_clk>, <>_crx_ref_clk>; + clock-names = "pss_ref_clk", "video_clk", "pss_alt_ref_clk","aux_ref_clk", "gt_crx_ref_clk"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index 3c9a57a8443b..9d8bbac27d8b 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -9,6 +9,7 @@ Required properties: "fsl,imx53-sdma" "fsl,imx6q-sdma" "fsl,imx7d-sdma" + "fsl,imx8mq-sdma" The -to variants should be preferred since they allow to determine the correct ROM script addresses needed for the driver to work without additional firmware. diff --git a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt index 614bac55df86..a4fe136be2ba 100644 --- a/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt +++ b/Documentation/devicetree/bindings/firmware/xilinx/xlnx,zynqmp-firmware.txt @@ -17,53 +17,6 @@ Required properties: - "smc" : SMC #0, following the SMCCC - "hvc" : HVC #0, following the SMCCC --------------------------------------------------------------------------- -Device Tree Clock bindings for the Zynq Ultrascale+ MPSoC controlled using -Zynq MPSoC firmware interface --------------------------------------------------------------------------- -The clock controller is a h/w block of Zynq Ultrascale+ MPSoC clock -tree. It reads required input clock frequencies from the devicetree and acts -as clock provider for all clock consumers of PS clocks. - -See clock_bindings.txt for more information on the generic clock bindings. - -Required properties: - - #clock-cells: Must be 1 - - compatible: Must contain: "xlnx,zynqmp-clk" - - clocks: List of clock specifiers which are external input - clocks to the given clock controller. Please refer - the next section to find the input clocks for a - given controller. - - clock-names: List of clock names which are exteral input clocks - to the given clock controller. Please refer to the - clock bindings for more details. - -Input clocks for zynqmp Ultrascale+ clock controller: - -The Zynq UltraScale+ MPSoC has one primary and four alternative reference clock -inputs. These required clock inputs are: - - pss_ref_clk (PS reference clock) - - video_clk (reference clock for video system ) - - pss_alt_ref_clk (alternative PS reference clock) - - aux_ref_clk - - gt_crx_ref_clk (transceiver reference clock) - -The following strings are optional parameters to the 'clock-names' property in -order to provide an optional (E)MIO clock source: - - swdt0_ext_clk - - swdt1_ext_clk - - gem0_emio_clk - - gem1_emio_clk - - gem2_emio_clk - - gem3_emio_clk - - mio_clk_XX # with XX = 00..77 - - mio_clk_50_or_51 #for the mux clock to gem tsu from 50 or 51 - - -Output clocks are registered based on clock information received -from firmware. Output clocks indexes are mentioned in -include/dt-bindings/clock/xlnx,zynqmp-clk.h. - ------- Example ------- @@ -72,11 +25,6 @@ firmware { zynqmp_firmware: zynqmp-firmware { compatible = "xlnx,zynqmp-firmware"; method = "smc"; - zynqmp_clk: clock-controller { - #clock-cells = <1>; - compatible = "xlnx,zynqmp-clk"; - clocks = <&pss_ref_clk>, <&video_clk>, <&pss_alt_ref_clk>, <&aux_ref_clk>, <>_crx_ref_clk>; - clock-names = "pss_ref_clk", "video_clk", "pss_alt_ref_clk","aux_ref_clk", "gt_crx_ref_clk"; - }; + ... }; }; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt index 18a2cde2e5f3..1b1a74129141 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt @@ -37,6 +37,20 @@ Optional properties: - operating-points-v2 : Refer to Documentation/devicetree/bindings/opp/opp.txt for details. +- resets : Phandle of the GPU reset line. + +Vendor-specific bindings +------------------------ + +The Mali GPU is integrated very differently from one SoC to +another. In order to accomodate those differences, you have the option +to specify one more vendor-specific compatible, among: + +- "amlogic,meson-gxm-mali" + Required properties: + - resets : Should contain phandles of : + + GPU reset line + + GPU APB glue reset line Example for a Mali-T760: diff --git a/Documentation/devicetree/bindings/i2c/i2c-xscale.txt b/Documentation/devicetree/bindings/i2c/i2c-iop3xx.txt index dcc8390e0d24..dcc8390e0d24 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-xscale.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-iop3xx.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt index ee4c32454198..ee4c32454198 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt b/Documentation/devicetree/bindings/i2c/i2c-stu300.txt index bd81a482634f..bd81a482634f 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stu300.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sun6i-p2wi.txt index 49df0053347a..49df0053347a 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sun6i-p2wi.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt b/Documentation/devicetree/bindings/i2c/i2c-wmt.txt index 94a425eaa6c7..94a425eaa6c7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-wmt.txt diff --git a/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt index 5c184b940669..f1f3a552459b 100644 --- a/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt @@ -10,6 +10,7 @@ Required properties: - clocks: The root clock of the ADC controller - clock-names: Must contain "adc", matching entry in the clocks property - vref-supply: The regulator supply ADC reference voltage +- #io-channel-cells: Must be 1 as per ../iio-bindings.txt Example: adc1: adc@30610000 { @@ -19,4 +20,5 @@ adc1: adc@30610000 { clocks = <&clks IMX7D_ADC_ROOT_CLK>; clock-names = "adc"; vref-supply = <®_vcc_3v3_mcu>; + #io-channel-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index 8de96a4fb2d5..f977ea7617f6 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -16,6 +16,7 @@ Required properties: - "renesas,irqc-r8a7793" (R-Car M2-N) - "renesas,irqc-r8a7794" (R-Car E2) - "renesas,intc-ex-r8a774a1" (RZ/G2M) + - "renesas,intc-ex-r8a774c0" (RZ/G2E) - "renesas,intc-ex-r8a7795" (R-Car H3) - "renesas,intc-ex-r8a7796" (R-Car M3-W) - "renesas,intc-ex-r8a77965" (R-Car M3-N) diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/mmdc.txt b/Documentation/devicetree/bindings/memory-controllers/fsl/mmdc.txt new file mode 100644 index 000000000000..bcc36c5b543c --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/mmdc.txt @@ -0,0 +1,35 @@ +Freescale Multi Mode DDR controller (MMDC) + +Required properties : +- compatible : should be one of following: + for i.MX6Q/i.MX6DL: + - "fsl,imx6q-mmdc"; + for i.MX6QP: + - "fsl,imx6qp-mmdc", "fsl,imx6q-mmdc"; + for i.MX6SL: + - "fsl,imx6sl-mmdc", "fsl,imx6q-mmdc"; + for i.MX6SLL: + - "fsl,imx6sll-mmdc", "fsl,imx6q-mmdc"; + for i.MX6SX: + - "fsl,imx6sx-mmdc", "fsl,imx6q-mmdc"; + for i.MX6UL/i.MX6ULL/i.MX6ULZ: + - "fsl,imx6ul-mmdc", "fsl,imx6q-mmdc"; + for i.MX7ULP: + - "fsl,imx7ulp-mmdc", "fsl,imx6q-mmdc"; +- reg : address and size of MMDC DDR controller registers + +Optional properties : +- clocks : the clock provided by the SoC to access the MMDC registers + +Example : + mmdc0: memory-controller@21b0000 { /* MMDC0 */ + compatible = "fsl,imx6q-mmdc"; + reg = <0x021b0000 0x4000>; + clocks = <&clks IMX6QDL_CLK_MMDC_P0_IPG>; + }; + + mmdc1: memory-controller@21b4000 { /* MMDC1 */ + compatible = "fsl,imx6q-mmdc"; + reg = <0x021b4000 0x4000>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt index 07242d141773..36c4bea675d5 100644 --- a/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/k3-dw-mshc.txt @@ -13,6 +13,8 @@ Required Properties: * compatible: should be one of the following. - "hisilicon,hi3660-dw-mshc": for controllers with hi3660 specific extensions. + - "hisilicon,hi3670-dw-mshc", "hisilicon,hi3660-dw-mshc": for controllers + with hi3670 specific extensions. - "hisilicon,hi4511-dw-mshc": for controllers with hi4511 specific extensions. - "hisilicon,hi6220-dw-mshc": for controllers with hi6220 specific extensions. diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt index bbcb255c3150..93a7469e70d4 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -12,10 +12,15 @@ Required properties: Subnodes: The integrated switch subnode should be specified according to the binding -described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of -port and PHY id, each subnode describing a port needs to have a valid phandle -referencing the internal PHY connected to it. The CPU port of this switch is -always port 0. +described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external +mdio-bus each subnode describing a port needs to have a valid phandle +referencing the internal PHY it is connected to. This is because there's no +N:N mapping of port and PHY id. + +Don't use mixed external and internal mdio-bus configurations, as this is +not supported by the hardware. + +The CPU port of this switch is always port 0. A CPU port node has the following optional node: @@ -31,8 +36,9 @@ For QCA8K the 'fixed-link' sub-node supports only the following properties: - 'full-duplex' (boolean, optional), to indicate that full duplex is used. When absent, half duplex is assumed. -Example: +Examples: +for the external mdio-bus configuration: &mdio0 { phy_port1: phy@0 { @@ -55,12 +61,12 @@ Example: reg = <4>; }; - switch0@0 { + switch@10 { compatible = "qca,qca8337"; #address-cells = <1>; #size-cells = <0>; - reg = <0>; + reg = <0x10>; ports { #address-cells = <1>; @@ -108,3 +114,56 @@ Example: }; }; }; + +for the internal master mdio-bus configuration: + + &mdio0 { + switch@10 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = 1000; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "wan"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt b/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt index 1cd050b4054c..0fdc3dd1125e 100644 --- a/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt +++ b/Documentation/devicetree/bindings/power/amlogic,meson-gx-pwrc.txt @@ -16,7 +16,9 @@ Device Tree Bindings: --------------------- Required properties: -- compatible: should be "amlogic,meson-gx-pwrc-vpu" for the Meson GX SoCs +- compatible: should be one of the following : + - "amlogic,meson-gx-pwrc-vpu" for the Meson GX SoCs + - "amlogic,meson-g12a-pwrc-vpu" for the Meson G12A SoCs - #power-domain-cells: should be 0 - amlogic,hhi-sysctrl: phandle to the HHI sysctrl node - resets: phandles to the reset lines needed for this power demain sequence diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi3660-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi3660-reset.txt index 2bf3344b2a02..2df4bddeb688 100644 --- a/Documentation/devicetree/bindings/reset/hisilicon,hi3660-reset.txt +++ b/Documentation/devicetree/bindings/reset/hisilicon,hi3660-reset.txt @@ -5,11 +5,12 @@ Please also refer to reset.txt in this directory for common reset controller binding usage. The reset controller registers are part of the system-ctl block on -hi3660 SoC. +hi3660 and hi3670 SoCs. Required properties: -- compatible: should be - "hisilicon,hi3660-reset" +- compatible: should be one of the following: + "hisilicon,hi3660-reset" for HI3660 + "hisilicon,hi3670-reset", "hisilicon,hi3660-reset" for HI3670 - hisi,rst-syscon: phandle of the reset's syscon. - #reset-cells : Specifies the number of cells needed to encode a reset source. The type shall be a <u32> and the value shall be 2. diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index 742cb470595b..bcfb13194f16 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -16,6 +16,7 @@ Required properties: * "mediatek,mt8127-uart" for MT8127 compatible UARTS * "mediatek,mt8135-uart" for MT8135 compatible UARTS * "mediatek,mt8173-uart" for MT8173 compatible UARTS + * "mediatek,mt8183-uart", "mediatek,mt6577-uart" for MT8183 compatible UARTS * "mediatek,mt6577-uart" for MT6577 and all of the above - reg: The base address of the UART register bank. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 8162b0eb4b50..24a9290b8116 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -54,6 +54,7 @@ avic Shanghai AVIC Optoelectronics Co., Ltd. avnet Avnet, Inc. axentia Axentia Technologies AB axis Axis Communications AB +azw Shenzhen AZW Technology Co., Ltd. bananapi BIPAI KEJI LIMITED bhf Beckhoff Automation GmbH & Co. KG bitmain Bitmain Technologies @@ -210,6 +211,7 @@ kiebackpeter Kieback & Peter GmbH kinetic Kinetic Technologies kingdisplay King & Display Technology Co., Ltd. kingnovel Kingnovel Technology Co., Ltd. +kobo Rakuten Kobo Inc. koe Kaohsiung Opto-Electronics Inc. kosagi Sutajio Ko-Usagi PTE Ltd. kyo Kyocera Corporation @@ -244,6 +246,7 @@ melexis Melexis N.V. melfas MELFAS Inc. mellanox Mellanox Technologies memsic MEMSIC Inc. +menlo Menlo Systems GmbH merrii Merrii Technology Co., Ltd. micrel Micrel Inc. microchip Microchip Technology Inc. @@ -287,6 +290,7 @@ nuvoton Nuvoton Technology Corporation nvd New Vision Display nvidia NVIDIA nxp NXP Semiconductors +oceanic Oceanic Systems (UK) Ltd. okaya Okaya Electric America, Inc. oki Oki Electric Industry Co., Ltd. olimex OLIMEX Ltd. @@ -353,6 +357,7 @@ sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler seagate Seagate Technology PLC +seirobotics Shenzhen SEI Robotics Co., Ltd semtech Semtech Corporation sensirion Sensirion AG sff Small Form Factor Committee @@ -361,6 +366,7 @@ sgx SGX Sensortech sharp Sharp Corporation shimafuji Shimafuji Electric, Inc. si-en Si-En Technology Ltd. +si-linux Silicon Linux Corporation sifive SiFive, Inc. sigma Sigma Designs, Inc. sii Seiko Instruments, Inc. @@ -415,6 +421,7 @@ toumaz Toumaz tpk TPK U.S.A. LLC tplink TP-LINK Technologies Co., Ltd. tpo TPO +tq TQ Systems GmbH tronfy Tronfy tronsmart Tronsmart truly Truly Semiconductors Limited diff --git a/Documentation/filesystems/mount_api.txt b/Documentation/filesystems/mount_api.txt index 944d1965e917..00ff0cfccfa7 100644 --- a/Documentation/filesystems/mount_api.txt +++ b/Documentation/filesystems/mount_api.txt @@ -12,11 +12,13 @@ CONTENTS (4) Filesystem context security. - (5) VFS filesystem context operations. + (5) VFS filesystem context API. - (6) Parameter description. + (6) Superblock creation helpers. - (7) Parameter helper functions. + (7) Parameter description. + + (8) Parameter helper functions. ======== @@ -41,12 +43,15 @@ The creation of new mounts is now to be done in a multistep process: (7) Destroy the context. -To support this, the file_system_type struct gains a new field: +To support this, the file_system_type struct gains two new fields: int (*init_fs_context)(struct fs_context *fc); + const struct fs_parameter_description *parameters; -which is invoked to set up the filesystem-specific parts of a filesystem -context, including the additional space. +The first is invoked to set up the filesystem-specific parts of a filesystem +context, including the additional space, and the second points to the +parameter description for validation at registration time and querying by a +future system call. Note that security initialisation is done *after* the filesystem is called so that the namespaces may be adjusted first. @@ -73,9 +78,9 @@ context. This is represented by the fs_context structure: void *s_fs_info; unsigned int sb_flags; unsigned int sb_flags_mask; + unsigned int s_iflags; + unsigned int lsm_flags; enum fs_context_purpose purpose:8; - bool sloppy:1; - bool silent:1; ... }; @@ -141,6 +146,10 @@ The fs_context fields are as follows: Which bits SB_* flags are to be set/cleared in super_block::s_flags. + (*) unsigned int s_iflags + + These will be bitwise-OR'd with s->s_iflags when a superblock is created. + (*) enum fs_context_purpose This indicates the purpose for which the context is intended. The @@ -150,17 +159,6 @@ The fs_context fields are as follows: FS_CONTEXT_FOR_SUBMOUNT -- New automatic submount of extant mount FS_CONTEXT_FOR_RECONFIGURE -- Change an existing mount - (*) bool sloppy - (*) bool silent - - These are set if the sloppy or silent mount options are given. - - [NOTE] sloppy is probably unnecessary when userspace passes over one - option at a time since the error can just be ignored if userspace deems it - to be unimportant. - - [NOTE] silent is probably redundant with sb_flags & SB_SILENT. - The mount context is created by calling vfs_new_fs_context() or vfs_dup_fs_context() and is destroyed with put_fs_context(). Note that the structure is not refcounted. @@ -342,28 +340,47 @@ number of operations used by the new mount code for this purpose: It should return 0 on success or a negative error code on failure. -================================= -VFS FILESYSTEM CONTEXT OPERATIONS -================================= +========================== +VFS FILESYSTEM CONTEXT API +========================== -There are four operations for creating a filesystem context and -one for destroying a context: +There are four operations for creating a filesystem context and one for +destroying a context: - (*) struct fs_context *vfs_new_fs_context(struct file_system_type *fs_type, - struct dentry *reference, - unsigned int sb_flags, - unsigned int sb_flags_mask, - enum fs_context_purpose purpose); + (*) struct fs_context *fs_context_for_mount( + struct file_system_type *fs_type, + unsigned int sb_flags); - Create a filesystem context for a given filesystem type and purpose. This - allocates the filesystem context, sets the superblock flags, initialises - the security and calls fs_type->init_fs_context() to initialise the - filesystem private data. + Allocate a filesystem context for the purpose of setting up a new mount, + whether that be with a new superblock or sharing an existing one. This + sets the superblock flags, initialises the security and calls + fs_type->init_fs_context() to initialise the filesystem private data. - reference can be NULL or it may indicate the root dentry of a superblock - that is going to be reconfigured (FS_CONTEXT_FOR_RECONFIGURE) or - the automount point that triggered a submount (FS_CONTEXT_FOR_SUBMOUNT). - This is provided as a source of namespace information. + fs_type specifies the filesystem type that will manage the context and + sb_flags presets the superblock flags stored therein. + + (*) struct fs_context *fs_context_for_reconfigure( + struct dentry *dentry, + unsigned int sb_flags, + unsigned int sb_flags_mask); + + Allocate a filesystem context for the purpose of reconfiguring an + existing superblock. dentry provides a reference to the superblock to be + configured. sb_flags and sb_flags_mask indicate which superblock flags + need changing and to what. + + (*) struct fs_context *fs_context_for_submount( + struct file_system_type *fs_type, + struct dentry *reference); + + Allocate a filesystem context for the purpose of creating a new mount for + an automount point or other derived superblock. fs_type specifies the + filesystem type that will manage the context and the reference dentry + supplies the parameters. Namespaces are propagated from the reference + dentry's superblock also. + + Note that it's not a requirement that the reference dentry be of the same + filesystem type as fs_type. (*) struct fs_context *vfs_dup_fs_context(struct fs_context *src_fc); @@ -390,20 +407,6 @@ context pointer or a negative error code. For the remaining operations, if an error occurs, a negative error code will be returned. - (*) int vfs_get_tree(struct fs_context *fc); - - Get or create the mountable root and superblock, using the parameters in - the filesystem context to select/configure the superblock. This invokes - the ->validate() op and then the ->get_tree() op. - - [NOTE] ->validate() could perhaps be rolled into ->get_tree() and - ->reconfigure(). - - (*) struct vfsmount *vfs_create_mount(struct fs_context *fc); - - Create a mount given the parameters in the specified filesystem context. - Note that this does not attach the mount to anything. - (*) int vfs_parse_fs_param(struct fs_context *fc, struct fs_parameter *param); @@ -432,17 +435,80 @@ returned. clear the pointer, but then becomes responsible for disposing of the object. - (*) int vfs_parse_fs_string(struct fs_context *fc, char *key, + (*) int vfs_parse_fs_string(struct fs_context *fc, const char *key, const char *value, size_t v_size); - A wrapper around vfs_parse_fs_param() that just passes a constant string. + A wrapper around vfs_parse_fs_param() that copies the value string it is + passed. (*) int generic_parse_monolithic(struct fs_context *fc, void *data); Parse a sys_mount() data page, assuming the form to be a text list consisting of key[=val] options separated by commas. Each item in the list is passed to vfs_mount_option(). This is the default when the - ->parse_monolithic() operation is NULL. + ->parse_monolithic() method is NULL. + + (*) int vfs_get_tree(struct fs_context *fc); + + Get or create the mountable root and superblock, using the parameters in + the filesystem context to select/configure the superblock. This invokes + the ->get_tree() method. + + (*) struct vfsmount *vfs_create_mount(struct fs_context *fc); + + Create a mount given the parameters in the specified filesystem context. + Note that this does not attach the mount to anything. + + +=========================== +SUPERBLOCK CREATION HELPERS +=========================== + +A number of VFS helpers are available for use by filesystems for the creation +or looking up of superblocks. + + (*) struct super_block * + sget_fc(struct fs_context *fc, + int (*test)(struct super_block *sb, struct fs_context *fc), + int (*set)(struct super_block *sb, struct fs_context *fc)); + + This is the core routine. If test is non-NULL, it searches for an + existing superblock matching the criteria held in the fs_context, using + the test function to match them. If no match is found, a new superblock + is created and the set function is called to set it up. + + Prior to the set function being called, fc->s_fs_info will be transferred + to sb->s_fs_info - and fc->s_fs_info will be cleared if set returns + success (ie. 0). + +The following helpers all wrap sget_fc(): + + (*) int vfs_get_super(struct fs_context *fc, + enum vfs_get_super_keying keying, + int (*fill_super)(struct super_block *sb, + struct fs_context *fc)) + + This creates/looks up a deviceless superblock. The keying indicates how + many superblocks of this type may exist and in what manner they may be + shared: + + (1) vfs_get_single_super + + Only one such superblock may exist in the system. Any further + attempt to get a new superblock gets this one (and any parameter + differences are ignored). + + (2) vfs_get_keyed_super + + Multiple superblocks of this type may exist and they're keyed on + their s_fs_info pointer (for example this may refer to a + namespace). + + (3) vfs_get_independent_super + + Multiple independent superblocks of this type may exist. This + function never matches an existing one and always creates a new + one. ===================== @@ -454,35 +520,22 @@ There's a core description struct that links everything together: struct fs_parameter_description { const char name[16]; - u8 nr_params; - u8 nr_alt_keys; - u8 nr_enums; - bool ignore_unknown; - bool no_source; - const char *const *keys; - const struct constant_table *alt_keys; const struct fs_parameter_spec *specs; const struct fs_parameter_enum *enums; }; For example: - enum afs_param { + enum { Opt_autocell, Opt_bar, Opt_dyn, Opt_foo, Opt_source, - nr__afs_params }; static const struct fs_parameter_description afs_fs_parameters = { .name = "kAFS", - .nr_params = nr__afs_params, - .nr_alt_keys = ARRAY_SIZE(afs_param_alt_keys), - .nr_enums = ARRAY_SIZE(afs_param_enums), - .keys = afs_param_keys, - .alt_keys = afs_param_alt_keys, .specs = afs_param_specs, .enums = afs_param_enums, }; @@ -494,28 +547,24 @@ The members are as follows: The name to be used in error messages generated by the parse helper functions. - (2) u8 nr_params; - - The number of discrete parameter identifiers. This indicates the number - of elements in the ->types[] array and also limits the values that may be - used in the values that the ->keys[] array maps to. - - It is expected that, for example, two parameters that are related, say - "acl" and "noacl" with have the same ID, but will be flagged to indicate - that one is the inverse of the other. The value can then be picked out - from the parse result. + (2) const struct fs_parameter_specification *specs; - (3) const struct fs_parameter_specification *specs; + Table of parameter specifications, terminated with a null entry, where the + entries are of type: - Table of parameter specifications, where the entries are of type: - - struct fs_parameter_type { - enum fs_parameter_spec type:8; - u8 flags; + struct fs_parameter_spec { + const char *name; + u8 opt; + enum fs_parameter_type type:8; + unsigned short flags; }; - and the parameter identifier is the index to the array. 'type' indicates - the desired value type and must be one of: + The 'name' field is a string to match exactly to the parameter key (no + wildcards, patterns and no case-independence) and 'opt' is the value that + will be returned by the fs_parser() function in the case of a successful + match. + + The 'type' field indicates the desired value type and must be one of: TYPE NAME EXPECTED VALUE RESULT IN ======================= ======================= ===================== @@ -525,85 +574,65 @@ The members are as follows: fs_param_is_u32_octal 32-bit octal int result->uint_32 fs_param_is_u32_hex 32-bit hex int result->uint_32 fs_param_is_s32 32-bit signed int result->int_32 + fs_param_is_u64 64-bit unsigned int result->uint_64 fs_param_is_enum Enum value name result->uint_32 fs_param_is_string Arbitrary string param->string fs_param_is_blob Binary blob param->blob fs_param_is_blockdev Blockdev path * Needs lookup fs_param_is_path Path * Needs lookup - fs_param_is_fd File descriptor param->file - - And each parameter can be qualified with 'flags': - - fs_param_v_optional The value is optional - fs_param_neg_with_no If key name is prefixed with "no", it is false - fs_param_neg_with_empty If value is "", it is false - fs_param_deprecated The parameter is deprecated. - - For example: - - static const struct fs_parameter_spec afs_param_specs[nr__afs_params] = { - [Opt_autocell] = { fs_param_is flag }, - [Opt_bar] = { fs_param_is_enum }, - [Opt_dyn] = { fs_param_is flag }, - [Opt_foo] = { fs_param_is_bool, fs_param_neg_with_no }, - [Opt_source] = { fs_param_is_string }, - }; + fs_param_is_fd File descriptor result->int_32 Note that if the value is of fs_param_is_bool type, fs_parse() will try to match any string value against "0", "1", "no", "yes", "false", "true". - [!] NOTE that the table must be sorted according to primary key name so - that ->keys[] is also sorted. - - (4) const char *const *keys; - - Table of primary key names for the parameters. There must be one entry - per defined parameter. The table is optional if ->nr_params is 0. The - table is just an array of names e.g.: + Each parameter can also be qualified with 'flags': - static const char *const afs_param_keys[nr__afs_params] = { - [Opt_autocell] = "autocell", - [Opt_bar] = "bar", - [Opt_dyn] = "dyn", - [Opt_foo] = "foo", - [Opt_source] = "source", - }; - - [!] NOTE that the table must be sorted such that the table can be searched - with bsearch() using strcmp(). This means that the Opt_* values must - correspond to the entries in this table. - - (5) const struct constant_table *alt_keys; - u8 nr_alt_keys; - - Table of additional key names and their mappings to parameter ID plus the - number of elements in the table. This is optional. The table is just an - array of { name, integer } pairs, e.g.: + fs_param_v_optional The value is optional + fs_param_neg_with_no result->negated set if key is prefixed with "no" + fs_param_neg_with_empty result->negated set if value is "" + fs_param_deprecated The parameter is deprecated. - static const struct constant_table afs_param_keys[] = { - { "baz", Opt_bar }, - { "dynamic", Opt_dyn }, + These are wrapped with a number of convenience wrappers: + + MACRO SPECIFIES + ======================= =============================================== + fsparam_flag() fs_param_is_flag + fsparam_flag_no() fs_param_is_flag, fs_param_neg_with_no + fsparam_bool() fs_param_is_bool + fsparam_u32() fs_param_is_u32 + fsparam_u32oct() fs_param_is_u32_octal + fsparam_u32hex() fs_param_is_u32_hex + fsparam_s32() fs_param_is_s32 + fsparam_u64() fs_param_is_u64 + fsparam_enum() fs_param_is_enum + fsparam_string() fs_param_is_string + fsparam_blob() fs_param_is_blob + fsparam_bdev() fs_param_is_blockdev + fsparam_path() fs_param_is_path + fsparam_fd() fs_param_is_fd + + all of which take two arguments, name string and option number - for + example: + + static const struct fs_parameter_spec afs_param_specs[] = { + fsparam_flag ("autocell", Opt_autocell), + fsparam_flag ("dyn", Opt_dyn), + fsparam_string ("source", Opt_source), + fsparam_flag_no ("foo", Opt_foo), + {} }; - [!] NOTE that the table must be sorted such that strcmp() can be used with - bsearch() to search the entries. - - The parameter ID can also be fs_param_key_removed to indicate that a - deprecated parameter has been removed and that an error will be given. - This differs from fs_param_deprecated where the parameter may still have - an effect. - - Further, the behaviour of the parameter may differ when an alternate name - is used (for instance with NFS, "v3", "v4.2", etc. are alternate names). + An addition macro, __fsparam() is provided that takes an additional pair + of arguments to specify the type and the flags for anything that doesn't + match one of the above macros. (6) const struct fs_parameter_enum *enums; - u8 nr_enums; - Table of enum value names to integer mappings and the number of elements - stored therein. This is of type: + Table of enum value names to integer mappings, terminated with a null + entry. This is of type: struct fs_parameter_enum { - u8 param_id; + u8 opt; char name[14]; u8 value; }; @@ -621,11 +650,6 @@ The members are as follows: try to look the value up in the enum table and the result will be stored in the parse result. - (7) bool no_source; - - If this is set, fs_parse() will ignore any "source" parameter and not - pass it to the filesystem. - The parser should be pointed to by the parser pointer in the file_system_type struct as this will provide validation on registration (if CONFIG_VALIDATE_FS_PARSER=y) and will allow the description to be queried from @@ -650,9 +674,8 @@ process the parameters it is given. int value; }; - and it must be sorted such that it can be searched using bsearch() using - strcmp(). If a match is found, the corresponding value is returned. If a - match isn't found, the not_found value is returned instead. + If a match is found, the corresponding value is returned. If a match + isn't found, the not_found value is returned instead. (*) bool validate_constant_table(const struct constant_table *tbl, size_t tbl_size, @@ -665,36 +688,36 @@ process the parameters it is given. should just be set to lie inside the low-to-high range. If all is good, true is returned. If the table is invalid, errors are - logged to dmesg, the stack is dumped and false is returned. + logged to dmesg and false is returned. + + (*) bool fs_validate_description(const struct fs_parameter_description *desc); + + This performs some validation checks on a parameter description. It + returns true if the description is good and false if it is not. It will + log errors to dmesg if validation fails. (*) int fs_parse(struct fs_context *fc, - const struct fs_param_parser *parser, + const struct fs_parameter_description *desc, struct fs_parameter *param, - struct fs_param_parse_result *result); + struct fs_parse_result *result); This is the main interpreter of parameters. It uses the parameter - description (parser) to look up the name of the parameter to use and to - convert that to a parameter ID (stored in result->key). + description to look up a parameter by key name and to convert that to an + option number (which it returns). If successful, and if the parameter type indicates the result is a boolean, integer or enum type, the value is converted by this function and - the result stored in result->{boolean,int_32,uint_32}. + the result stored in result->{boolean,int_32,uint_32,uint_64}. If a match isn't initially made, the key is prefixed with "no" and no value is present then an attempt will be made to look up the key with the prefix removed. If this matches a parameter for which the type has flag - fs_param_neg_with_no set, then a match will be made and the value will be - set to false/0/NULL. - - If the parameter is successfully matched and, optionally, parsed - correctly, 1 is returned. If the parameter isn't matched and - parser->ignore_unknown is set, then 0 is returned. Otherwise -EINVAL is - returned. - - (*) bool fs_validate_description(const struct fs_parameter_description *desc); + fs_param_neg_with_no set, then a match will be made and result->negated + will be set to true. - This is validates the parameter description. It returns true if the - description is good and false if it is not. + If the parameter isn't matched, -ENOPARAM will be returned; if the + parameter is matched, but the value is erroneous, -EINVAL will be + returned; otherwise the parameter's option number will be returned. (*) int fs_lookup_param(struct fs_context *fc, struct fs_parameter *value, diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801 index d1ee484a787d..ee9984f35868 100644 --- a/Documentation/i2c/busses/i2c-i801 +++ b/Documentation/i2c/busses/i2c-i801 @@ -36,6 +36,7 @@ Supported adapters: * Intel Cannon Lake (PCH) * Intel Cedar Fork (PCH) * Intel Ice Lake (PCH) + * Intel Comet Lake (PCH) Datasheets: Publicly available at the Intel website On Intel Patsburg and later chipsets, both the normal host SMBus controller diff --git a/Documentation/networking/msg_zerocopy.rst b/Documentation/networking/msg_zerocopy.rst index 18c1415e7bfa..ace56204dd03 100644 --- a/Documentation/networking/msg_zerocopy.rst +++ b/Documentation/networking/msg_zerocopy.rst @@ -50,7 +50,7 @@ the excellent reporting over at LWN.net or read the original code. patchset [PATCH net-next v4 0/9] socket sendmsg MSG_ZEROCOPY - http://lkml.kernel.org/r/20170803202945.70750-1-willemdebruijn.kernel@gmail.com + https://lkml.kernel.org/netdev/20170803202945.70750-1-willemdebruijn.kernel@gmail.com Interface diff --git a/Documentation/networking/netdev-FAQ.rst b/Documentation/networking/netdev-FAQ.rst index 0ac5fa77f501..8c7a713cf657 100644 --- a/Documentation/networking/netdev-FAQ.rst +++ b/Documentation/networking/netdev-FAQ.rst @@ -131,6 +131,19 @@ it to the maintainer to figure out what is the most recent and current version that should be applied. If there is any doubt, the maintainer will reply and ask what should be done. +Q: I made changes to only a few patches in a patch series should I resend only those changed? +-------------------------------------------------------------------------------------------- +A: No, please resend the entire patch series and make sure you do number your +patches such that it is clear this is the latest and greatest set of patches +that can be applied. + +Q: I submitted multiple versions of a patch series and it looks like a version other than the last one has been accepted, what should I do? +------------------------------------------------------------------------------------------------------------------------------------------- +A: There is no revert possible, once it is pushed out, it stays like that. +Please send incremental versions on top of what has been merged in order to fix +the patches the way they would look like if your latest patch series was to be +merged. + Q: How can I tell what patches are queued up for backporting to the various stable releases? -------------------------------------------------------------------------------------------- A: Normally Greg Kroah-Hartman collects stable commits himself, but for diff --git a/Documentation/networking/nf_flowtable.txt b/Documentation/networking/nf_flowtable.txt index 54128c50d508..ca2136c76042 100644 --- a/Documentation/networking/nf_flowtable.txt +++ b/Documentation/networking/nf_flowtable.txt @@ -44,10 +44,10 @@ including the Netfilter hooks and the flowtable fastpath bypass. / \ / \ |Routing | / \ --> ingress ---> prerouting ---> |decision| | postrouting |--> neigh_xmit \_________/ \__________/ ---------- \____________/ ^ - | ^ | | ^ | - flowtable | | ____\/___ | | - | | | / \ | | - __\/___ | --------->| forward |------------ | + | ^ | ^ | + flowtable | ____\/___ | | + | | / \ | | + __\/___ | | forward |------------ | |-----| | \_________/ | |-----| | 'flow offload' rule | |-----| | adds entry to | diff --git a/Documentation/networking/snmp_counter.rst b/Documentation/networking/snmp_counter.rst index 52b026be028f..38a4edc4522b 100644 --- a/Documentation/networking/snmp_counter.rst +++ b/Documentation/networking/snmp_counter.rst @@ -413,7 +413,7 @@ algorithm. .. _F-RTO: https://tools.ietf.org/html/rfc5682 TCP Fast Path -============ +============= When kernel receives a TCP packet, it has two paths to handler the packet, one is fast path, another is slow path. The comment in kernel code provides a good explanation of them, I pasted them below:: @@ -681,6 +681,7 @@ The TCP stack receives an out of order duplicate packet, so it sends a DSACK to the sender. * TcpExtTCPDSACKRecv + The TCP stack receives a DSACK, which indicates an acknowledged duplicate packet is received. @@ -690,7 +691,7 @@ The TCP stack receives a DSACK, which indicate an out of order duplicate packet is received. invalid SACK and DSACK -==================== +====================== When a SACK (or DSACK) block is invalid, a corresponding counter would be updated. The validation method is base on the start/end sequence number of the SACK block. For more details, please refer the comment @@ -704,11 +705,13 @@ explaination: .. _Add counters for discarded SACK blocks: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=18f02545a9a16c9a89778b91a162ad16d510bb32 * TcpExtTCPSACKDiscard + This counter indicates how many SACK blocks are invalid. If the invalid SACK block is caused by ACK recording, the TCP stack will only ignore it and won't update this counter. * TcpExtTCPDSACKIgnoredOld and TcpExtTCPDSACKIgnoredNoUndo + When a DSACK block is invalid, one of these two counters would be updated. Which counter will be updated depends on the undo_marker flag of the TCP socket. If the undo_marker is not set, the TCP stack isn't @@ -719,7 +722,7 @@ will be updated. If the undo_marker is set, TcpExtTCPDSACKIgnoredOld will be updated. As implied in its name, it might be an old packet. SACK shift -========= +========== The linux networking stack stores data in sk_buff struct (skb for short). If a SACK block acrosses multiple skb, the TCP stack will try to re-arrange data in these skb. E.g. if a SACK block acknowledges seq @@ -730,12 +733,15 @@ seq 14 to 20. All data in skb2 will be moved to skb1, and skb2 will be discard, this operation is 'merge'. * TcpExtTCPSackShifted + A skb is shifted * TcpExtTCPSackMerged + A skb is merged * TcpExtTCPSackShiftFallback + A skb should be shifted or merged, but the TCP stack doesn't do it for some reasons. diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt index 7de9eee73fcd..67068c47c591 100644 --- a/Documentation/virtual/kvm/api.txt +++ b/Documentation/virtual/kvm/api.txt @@ -5,25 +5,32 @@ The Definitive KVM (Kernel-based Virtual Machine) API Documentation ---------------------- The kvm API is a set of ioctls that are issued to control various aspects -of a virtual machine. The ioctls belong to three classes +of a virtual machine. The ioctls belong to three classes: - System ioctls: These query and set global attributes which affect the whole kvm subsystem. In addition a system ioctl is used to create - virtual machines + virtual machines. - VM ioctls: These query and set attributes that affect an entire virtual machine, for example memory layout. In addition a VM ioctl is used to - create virtual cpus (vcpus). + create virtual cpus (vcpus) and devices. - Only run VM ioctls from the same process (address space) that was used - to create the VM. + VM ioctls must be issued from the same process (address space) that was + used to create the VM. - vcpu ioctls: These query and set attributes that control the operation of a single virtual cpu. - Only run vcpu ioctls from the same thread that was used to create the - vcpu. + vcpu ioctls should be issued from the same thread that was used to create + the vcpu, except for asynchronous vcpu ioctl that are marked as such in + the documentation. Otherwise, the first ioctl after switching threads + could see a performance impact. + - device ioctls: These query and set attributes that control the operation + of a single device. + + device ioctls must be issued from the same process (address space) that + was used to create the VM. 2. File descriptors ------------------- @@ -32,17 +39,34 @@ The kvm API is centered around file descriptors. An initial open("/dev/kvm") obtains a handle to the kvm subsystem; this handle can be used to issue system ioctls. A KVM_CREATE_VM ioctl on this handle will create a VM file descriptor which can be used to issue VM -ioctls. A KVM_CREATE_VCPU ioctl on a VM fd will create a virtual cpu -and return a file descriptor pointing to it. Finally, ioctls on a vcpu -fd can be used to control the vcpu, including the important task of -actually running guest code. +ioctls. A KVM_CREATE_VCPU or KVM_CREATE_DEVICE ioctl on a VM fd will +create a virtual cpu or device and return a file descriptor pointing to +the new resource. Finally, ioctls on a vcpu or device fd can be used +to control the vcpu or device. For vcpus, this includes the important +task of actually running guest code. In general file descriptors can be migrated among processes by means of fork() and the SCM_RIGHTS facility of unix domain socket. These kinds of tricks are explicitly not supported by kvm. While they will not cause harm to the host, their actual behavior is not guaranteed by -the API. The only supported use is one virtual machine per process, -and one vcpu per thread. +the API. See "General description" for details on the ioctl usage +model that is supported by KVM. + +It is important to note that althought VM ioctls may only be issued from +the process that created the VM, a VM's lifecycle is associated with its +file descriptor, not its creator (process). In other words, the VM and +its resources, *including the associated address space*, are not freed +until the last reference to the VM's file descriptor has been released. +For example, if fork() is issued after ioctl(KVM_CREATE_VM), the VM will +not be freed until both the parent (original) process and its child have +put their references to the VM's file descriptor. + +Because a VM's resources are not freed until the last reference to its +file descriptor is released, creating additional references to a VM via +via fork(), dup(), etc... without careful consideration is strongly +discouraged and may have unwanted side effects, e.g. memory allocated +by and on behalf of the VM's process may not be freed/unaccounted when +the VM is shut down. It is important to note that althought VM ioctls may only be issued from @@ -515,11 +539,15 @@ c) KVM_INTERRUPT_SET_LEVEL Note that any value for 'irq' other than the ones stated above is invalid and incurs unexpected behavior. +This is an asynchronous vcpu ioctl and can be invoked from any thread. + MIPS: Queues an external interrupt to be injected into the virtual CPU. A negative interrupt number dequeues the interrupt. +This is an asynchronous vcpu ioctl and can be invoked from any thread. + 4.17 KVM_DEBUG_GUEST @@ -1086,14 +1114,12 @@ struct kvm_userspace_memory_region { #define KVM_MEM_LOG_DIRTY_PAGES (1UL << 0) #define KVM_MEM_READONLY (1UL << 1) -This ioctl allows the user to create or modify a guest physical memory -slot. When changing an existing slot, it may be moved in the guest -physical memory space, or its flags may be modified. It may not be -resized. Slots may not overlap in guest physical address space. -Bits 0-15 of "slot" specifies the slot id and this value should be -less than the maximum number of user memory slots supported per VM. -The maximum allowed slots can be queried using KVM_CAP_NR_MEMSLOTS, -if this capability is supported by the architecture. +This ioctl allows the user to create, modify or delete a guest physical +memory slot. Bits 0-15 of "slot" specify the slot id and this value +should be less than the maximum number of user memory slots supported per +VM. The maximum allowed slots can be queried using KVM_CAP_NR_MEMSLOTS, +if this capability is supported by the architecture. Slots may not +overlap in guest physical address space. If KVM_CAP_MULTI_ADDRESS_SPACE is available, bits 16-31 of "slot" specifies the address space which is being modified. They must be @@ -1102,6 +1128,10 @@ KVM_CAP_MULTI_ADDRESS_SPACE capability. Slots in separate address spaces are unrelated; the restriction on overlapping slots only applies within each address space. +Deleting a slot is done by passing zero for memory_size. When changing +an existing slot, it may be moved in the guest physical memory space, +or its flags may be modified, but it may not be resized. + Memory for the region is taken starting at the address denoted by the field userspace_addr, which must point at user addressable memory for the entire memory slot size. Any object may back this memory, including @@ -2493,7 +2523,7 @@ KVM_S390_MCHK (vm, vcpu) - machine check interrupt; cr 14 bits in parm, machine checks needing further payload are not supported by this ioctl) -Note that the vcpu ioctl is asynchronous to vcpu execution. +This is an asynchronous vcpu ioctl and can be invoked from any thread. 4.78 KVM_PPC_GET_HTAB_FD @@ -3042,8 +3072,7 @@ KVM_S390_INT_EMERGENCY - sigp emergency; parameters in .emerg KVM_S390_INT_EXTERNAL_CALL - sigp external call; parameters in .extcall KVM_S390_MCHK - machine check interrupt; parameters in .mchk - -Note that the vcpu ioctl is asynchronous to vcpu execution. +This is an asynchronous vcpu ioctl and can be invoked from any thread. 4.94 KVM_S390_GET_IRQ_STATE diff --git a/Documentation/virtual/kvm/mmu.txt b/Documentation/virtual/kvm/mmu.txt index f365102c80f5..2efe0efc516e 100644 --- a/Documentation/virtual/kvm/mmu.txt +++ b/Documentation/virtual/kvm/mmu.txt @@ -142,7 +142,7 @@ Shadow pages contain the following information: If clear, this page corresponds to a guest page table denoted by the gfn field. role.quadrant: - When role.cr4_pae=0, the guest uses 32-bit gptes while the host uses 64-bit + When role.gpte_is_8_bytes=0, the guest uses 32-bit gptes while the host uses 64-bit sptes. That means a guest page table contains more ptes than the host, so multiple shadow pages are needed to shadow one guest page. For first-level shadow pages, role.quadrant can be 0 or 1 and denotes the @@ -158,9 +158,9 @@ Shadow pages contain the following information: The page is invalid and should not be used. It is a root page that is currently pinned (by a cpu hardware register pointing to it); once it is unpinned it will be destroyed. - role.cr4_pae: - Contains the value of cr4.pae for which the page is valid (e.g. whether - 32-bit or 64-bit gptes are in use). + role.gpte_is_8_bytes: + Reflects the size of the guest PTE for which the page is valid, i.e. '1' + if 64-bit gptes are in use, '0' if 32-bit gptes are in use. role.nxe: Contains the value of efer.nxe for which the page is valid. role.cr0_wp: @@ -173,6 +173,9 @@ Shadow pages contain the following information: Contains the value of cr4.smap && !cr0.wp for which the page is valid (pages for which this is true are different from other pages; see the treatment of cr0.wp=0 below). + role.ept_sp: + This is a virtual flag to denote a shadowed nested EPT page. ept_sp + is true if "cr0_wp && smap_andnot_wp", an otherwise invalid combination. role.smm: Is 1 if the page is valid in system management mode. This field determines which of the kvm_memslots array was used to build this |