diff options
Diffstat (limited to 'Documentation')
85 files changed, 1266 insertions, 128 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-i2c-devices-pca954x b/Documentation/ABI/testing/sysfs-bus-i2c-devices-pca954x new file mode 100644 index 000000000000..0b0de8cd0d13 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-i2c-devices-pca954x @@ -0,0 +1,20 @@ +What: /sys/bus/i2c/.../idle_state +Date: January 2019 +KernelVersion: 5.2 +Contact: Robert Shearman <robert.shearman@att.com> +Description: + Value that exists only for mux devices that can be + written to control the behaviour of the multiplexer on + idle. Possible values: + -2 - disconnect on idle, i.e. deselect the last used + channel, which is useful when there is a device + with an address that conflicts with another + device on another mux on the same parent bus. + -1 - leave the mux as-is, which is the most optimal + setting in terms of I2C operations and is the + default mode. + 0..<nchans> - set the mux to a predetermined channel, + which is useful if there is one channel that is + used almost always, and you want to reduce the + latency for normal operations after rare + transactions on other channels diff --git a/Documentation/DMA-API-HOWTO.txt b/Documentation/DMA-API-HOWTO.txt index db48c6fd3162..cb712a02f59f 100644 --- a/Documentation/DMA-API-HOWTO.txt +++ b/Documentation/DMA-API-HOWTO.txt @@ -365,13 +365,12 @@ __get_free_pages() (but takes size instead of a page order). If your driver needs regions sized smaller than a page, you may prefer using the dma_pool interface, described below. -The consistent DMA mapping interfaces, for non-NULL dev, will by -default return a DMA address which is 32-bit addressable. Even if the -device indicates (via DMA mask) that it may address the upper 32-bits, -consistent allocation will only return > 32-bit addresses for DMA if -the consistent DMA mask has been explicitly changed via -dma_set_coherent_mask(). This is true of the dma_pool interface as -well. +The consistent DMA mapping interfaces, will by default return a DMA address +which is 32-bit addressable. Even if the device indicates (via the DMA mask) +that it may address the upper 32-bits, consistent allocation will only +return > 32-bit addresses for DMA if the consistent DMA mask has been +explicitly changed via dma_set_coherent_mask(). This is true of the +dma_pool interface as well. dma_alloc_coherent() returns two values: the virtual address which you can use to access it from the CPU and dma_handle which you pass to the diff --git a/Documentation/admin-guide/cgroup-v2.rst b/Documentation/admin-guide/cgroup-v2.rst index 20f92c16ffbf..88e746074252 100644 --- a/Documentation/admin-guide/cgroup-v2.rst +++ b/Documentation/admin-guide/cgroup-v2.rst @@ -864,6 +864,8 @@ All cgroup core files are prefixed with "cgroup." populated 1 if the cgroup or its descendants contains any live processes; otherwise, 0. + frozen + 1 if the cgroup is frozen; otherwise, 0. cgroup.max.descendants A read-write single value files. The default is "max". @@ -897,6 +899,31 @@ All cgroup core files are prefixed with "cgroup." A dying cgroup can consume system resources not exceeding limits, which were active at the moment of cgroup deletion. + cgroup.freeze + A read-write single value file which exists on non-root cgroups. + Allowed values are "0" and "1". The default is "0". + + Writing "1" to the file causes freezing of the cgroup and all + descendant cgroups. This means that all belonging processes will + be stopped and will not run until the cgroup will be explicitly + unfrozen. Freezing of the cgroup may take some time; when this action + is completed, the "frozen" value in the cgroup.events control file + will be updated to "1" and the corresponding notification will be + issued. + + A cgroup can be frozen either by its own settings, or by settings + of any ancestor cgroups. If any of ancestor cgroups is frozen, the + cgroup will remain frozen. + + Processes in the frozen cgroup can be killed by a fatal signal. + They also can enter and leave a frozen cgroup: either by an explicit + move by a user, or if freezing of the cgroup races with fork(). + If a process is moved to a frozen cgroup, it stops. If a process is + moved out of a frozen cgroup, it becomes running. + + Frozen status of a cgroup doesn't affect any cgroup tree operations: + it's possible to delete a frozen (and empty) cgroup, as well as + create new sub-cgroups. Controllers =========== diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index fd03e2b629bb..a1fe7e8c4f15 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -1588,7 +1588,7 @@ Format: { "off" | "enforce" | "fix" | "log" } default: "enforce" - ima_appraise_tcb [IMA] + ima_appraise_tcb [IMA] Deprecated. Use ima_policy= instead. The builtin appraise policy appraises all files owned by uid=0. @@ -1615,8 +1615,7 @@ uid=0. The "appraise_tcb" policy appraises the integrity of - all files owned by root. (This is the equivalent - of ima_appraise_tcb.) + all files owned by root. The "secure_boot" policy appraises the integrity of files (eg. kexec kernel image, kernel modules, diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt index de4075413d91..161e63a6c254 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt @@ -14,6 +14,8 @@ Required Properties: - "mediatek,mt7629-apmixedsys" - "mediatek,mt8135-apmixedsys" - "mediatek,mt8173-apmixedsys" + - "mediatek,mt8183-apmixedsys", "syscon" + - "mediatek,mt8516-apmixedsys" - #clock-cells: Must be 1 The apmixedsys controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt index d1606b2c3e63..f3cef1a6d95c 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt @@ -9,6 +9,7 @@ Required Properties: - "mediatek,mt2701-audsys", "syscon" - "mediatek,mt7622-audsys", "syscon" - "mediatek,mt7623-audsys", "mediatek,mt2701-audsys", "syscon" + - "mediatek,mt8183-audiosys", "syscon" - #clock-cells: Must be 1 The AUDSYS controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,camsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,camsys.txt new file mode 100644 index 000000000000..d8930f64aa98 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,camsys.txt @@ -0,0 +1,22 @@ +MediaTek CAMSYS controller +============================ + +The MediaTek camsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be one of: + - "mediatek,mt8183-camsys", "syscon" +- #clock-cells: Must be 1 + +The camsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +camsys: camsys@1a000000 { + compatible = "mediatek,mt8183-camsys", "syscon"; + reg = <0 0x1a000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt index 3f99672163e3..e3bc4a1e7a6e 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt @@ -11,6 +11,7 @@ Required Properties: - "mediatek,mt6797-imgsys", "syscon" - "mediatek,mt7623-imgsys", "mediatek,mt2701-imgsys", "syscon" - "mediatek,mt8173-imgsys", "syscon" + - "mediatek,mt8183-imgsys", "syscon" - #clock-cells: Must be 1 The imgsys controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt index 417bd83d1378..a90913988d7e 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt @@ -15,6 +15,8 @@ Required Properties: - "mediatek,mt7629-infracfg", "syscon" - "mediatek,mt8135-infracfg", "syscon" - "mediatek,mt8173-infracfg", "syscon" + - "mediatek,mt8183-infracfg", "syscon" + - "mediatek,mt8516-infracfg", "syscon" - #clock-cells: Must be 1 - #reset-cells: Must be 1 diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ipu.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ipu.txt new file mode 100644 index 000000000000..aabc8c5c8ed2 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ipu.txt @@ -0,0 +1,43 @@ +Mediatek IPU controller +============================ + +The Mediatek ipu controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be one of: + - "mediatek,mt8183-ipu_conn", "syscon" + - "mediatek,mt8183-ipu_adl", "syscon" + - "mediatek,mt8183-ipu_core0", "syscon" + - "mediatek,mt8183-ipu_core1", "syscon" +- #clock-cells: Must be 1 + +The ipu controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +ipu_conn: syscon@19000000 { + compatible = "mediatek,mt8183-ipu_conn", "syscon"; + reg = <0 0x19000000 0 0x1000>; + #clock-cells = <1>; +}; + +ipu_adl: syscon@19010000 { + compatible = "mediatek,mt8183-ipu_adl", "syscon"; + reg = <0 0x19010000 0 0x1000>; + #clock-cells = <1>; +}; + +ipu_core0: syscon@19180000 { + compatible = "mediatek,mt8183-ipu_core0", "syscon"; + reg = <0 0x19180000 0 0x1000>; + #clock-cells = <1>; +}; + +ipu_core1: syscon@19280000 { + compatible = "mediatek,mt8183-ipu_core1", "syscon"; + reg = <0 0x19280000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mcucfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mcucfg.txt index b8fb03f3613e..2b882b7ca72e 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mcucfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mcucfg.txt @@ -7,6 +7,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2712-mcucfg", "syscon" + - "mediatek,mt8183-mcucfg", "syscon" - #clock-cells: Must be 1 The mcucfg controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mfgcfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mfgcfg.txt index 859e67b416d5..72787e7dd227 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mfgcfg.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mfgcfg.txt @@ -7,6 +7,7 @@ Required Properties: - compatible: Should be one of: - "mediatek,mt2712-mfgcfg", "syscon" + - "mediatek,mt8183-mfgcfg", "syscon" - #clock-cells: Must be 1 The mfgcfg controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt index 15d977afad31..545eab717c96 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt @@ -11,6 +11,7 @@ Required Properties: - "mediatek,mt6797-mmsys", "syscon" - "mediatek,mt7623-mmsys", "mediatek,mt2701-mmsys", "syscon" - "mediatek,mt8173-mmsys", "syscon" + - "mediatek,mt8183-mmsys", "syscon" - #clock-cells: Must be 1 The mmsys controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt index d160c2b4b6fe..a023b8338960 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt @@ -14,6 +14,8 @@ Required Properties: - "mediatek,mt7629-topckgen" - "mediatek,mt8135-topckgen" - "mediatek,mt8173-topckgen" + - "mediatek,mt8183-topckgen", "syscon" + - "mediatek,mt8516-topckgen" - #clock-cells: Must be 1 The topckgen controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt index 3212afc753c8..57176bb8dbb5 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt @@ -11,6 +11,7 @@ Required Properties: - "mediatek,mt6797-vdecsys", "syscon" - "mediatek,mt7623-vdecsys", "mediatek,mt2701-vdecsys", "syscon" - "mediatek,mt8173-vdecsys", "syscon" + - "mediatek,mt8183-vdecsys", "syscon" - #clock-cells: Must be 1 The vdecsys controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt index 851545357e94..c9faa6269087 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt @@ -9,6 +9,7 @@ Required Properties: - "mediatek,mt2712-vencsys", "syscon" - "mediatek,mt6797-vencsys", "syscon" - "mediatek,mt8173-vencsys", "syscon" + - "mediatek,mt8183-vencsys", "syscon" - #clock-cells: Must be 1 The vencsys controller uses the common clk binding from diff --git a/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt index 61777ad24f61..0f777749f4f1 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt @@ -6,7 +6,8 @@ devices. Required Properties: -- compatible : should be "amlogic,axg-audio-clkc" for the A113X and A113D +- compatible : should be "amlogic,axg-audio-clkc" for the A113X and A113D, + "amlogic,g12a-audio-clkc" for G12A. - reg : physical base address of the clock controller and length of memory mapped region. - clocks : a list of phandle + clock-specifier pairs for the clocks listed diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index e9f70fcdfe80..b520280e33ff 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -8,35 +8,30 @@ Slow Clock controller: Required properties: - compatible : shall be one of the following: - "atmel,at91sam9x5-sckc" or + "atmel,at91sam9x5-sckc", + "atmel,sama5d3-sckc" or "atmel,sama5d4-sckc": at91 SCKC (Slow Clock Controller) - This node contains the slow clock definitions. - - "atmel,at91sam9x5-clk-slow-osc": - at91 slow oscillator - - "atmel,at91sam9x5-clk-slow-rc-osc": - at91 internal slow RC oscillator -- reg : defines the IO memory reserved for the SCKC. -- #size-cells : shall be 0 (reg is used to encode clk id). -- #address-cells : shall be 1 (reg is used to encode clk id). +- #clock-cells : shall be 0. +- clocks : shall be the input parent clock phandle for the clock. +Optional properties: +- atmel,osc-bypass : boolean property. Set this when a clock signal is directly + provided on XIN. For example: - sckc: sckc@fffffe50 { - compatible = "atmel,sama5d3-pmc"; - reg = <0xfffffe50 0x4> - #size-cells = <0>; - #address-cells = <1>; - - /* put at91 slow clocks here */ + sckc@fffffe50 { + compatible = "atmel,at91sam9x5-sckc"; + reg = <0xfffffe50 0x4>; + clocks = <&slow_xtal>; + #clock-cells = <0>; }; Power Management Controller (PMC): Required properties: -- compatible : shall be "atmel,<chip>-pmc", "syscon": +- compatible : shall be "atmel,<chip>-pmc", "syscon" or + "microchip,sam9x60-pmc" <chip> can be: at91rm9200, at91sam9260, at91sam9261, at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9g15, at91sam9g25, at91sam9g35, at91sam9x25, at91sam9x35, at91sam9x5, diff --git a/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt new file mode 100644 index 000000000000..b8d8ef3bdc5f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt @@ -0,0 +1,93 @@ +Cirrus Logic Lochnagar Audio Development Board + +Lochnagar is an evaluation and development board for Cirrus Logic +Smart CODEC and Amp devices. It allows the connection of most Cirrus +Logic devices on mini-cards, as well as allowing connection of +various application processor systems to provide a full evaluation +platform. Audio system topology, clocking and power can all be +controlled through the Lochnagar, allowing the device under test +to be used in a variety of possible use cases. + +This binding document describes the binding for the clock portion of +the driver. + +Also see these documents for generic binding information: + [1] Clock : ../clock/clock-bindings.txt + +And these for relevant defines: + [2] include/dt-bindings/clock/lochnagar.h + +This binding must be part of the Lochnagar MFD binding: + [3] ../mfd/cirrus,lochnagar.txt + +Required properties: + + - compatible : One of the following strings: + "cirrus,lochnagar1-clk" + "cirrus,lochnagar2-clk" + + - #clock-cells : Must be 1. The first cell indicates the clock + number, see [2] for available clocks and [1]. + +Optional properties: + + - clocks : Must contain an entry for each clock in clock-names. + - clock-names : May contain entries for each of the following + clocks: + - ln-cdc-clkout : Output clock from CODEC card. + - ln-dsp-clkout : Output clock from DSP card. + - ln-gf-mclk1,ln-gf-mclk2,ln-gf-mclk3,ln-gf-mclk4 : Optional + input audio clocks from host system. + - ln-psia1-mclk, ln-psia2-mclk : Optional input audio clocks from + external connector. + - ln-spdif-clkout : Optional input audio clock from SPDIF. + - ln-adat-mclk : Optional input audio clock from ADAT. + - ln-pmic-32k : On board fixed clock. + - ln-clk-12m : On board fixed clock. + - ln-clk-11m : On board fixed clock. + - ln-clk-24m : On board fixed clock. + - ln-clk-22m : On board fixed clock. + - ln-clk-8m : On board fixed clock. + - ln-usb-clk-24m : On board fixed clock. + - ln-usb-clk-12m : On board fixed clock. + + - assigned-clocks : A list of Lochnagar clocks to be reparented, see + [2] for available clocks. + - assigned-clock-parents : Parents to be assigned to the clocks + listed in "assigned-clocks". + +Optional nodes: + + - fixed-clock nodes may be registered for the following on board clocks: + - ln-pmic-32k : 32768 Hz + - ln-clk-12m : 12288000 Hz + - ln-clk-11m : 11298600 Hz + - ln-clk-24m : 24576000 Hz + - ln-clk-22m : 22579200 Hz + - ln-clk-8m : 8192000 Hz + - ln-usb-clk-24m : 24576000 Hz + - ln-usb-clk-12m : 12288000 Hz + +Example: + +lochnagar { + lochnagar-clk { + compatible = "cirrus,lochnagar2-clk"; + + #clock-cells = <1>; + + clocks = <&clk-audio>, <&clk_pmic>; + clock-names = "ln-gf-mclk2", "ln-pmic-32k"; + + assigned-clocks = <&lochnagar-clk LOCHNAGAR_CDC_MCLK1>, + <&lochnagar-clk LOCHNAGAR_CDC_MCLK2>; + assigned-clock-parents = <&clk-audio>, + <&clk-pmic>; + }; + + clk-pmic: clk-pmic { + compatible = "fixed-clock"; + clock-cells = <0>; + clock-frequency = <32768>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/milbeaut-clock.yaml b/Documentation/devicetree/bindings/clock/milbeaut-clock.yaml new file mode 100644 index 000000000000..5cf0b811821e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/milbeaut-clock.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bindings/clock/milbeaut-clock.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Milbeaut SoCs Clock Controller Binding + +maintainers: + - Taichi Sugaya <sugaya.taichi@socionext.com> + +description: | + Milbeaut SoCs Clock controller is an integrated clock controller, which + generates and supplies to all modules. + + This binding uses common clock bindings + [1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +properties: + compatible: + oneOf: + - items: + - enum: + - socionext,milbeaut-m10v-ccu + clocks: + maxItems: 1 + description: external clock + + '#clock-cells': + const: 1 + +required: + - compatible + - reg + - clocks + - '#clock-cells' + +examples: + # Clock controller node: + - | + m10v-clk-ctrl@1d021000 { + compatible = "socionext,milbeaut-m10v-clk-ccu"; + reg = <0x1d021000 0x4000>; + #clock-cells = <1>; + clocks = <&clki40mhz>; + }; + + # Required an external clock for Clock controller node: + - | + clocks { + clki40mhz: clki40mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <40000000>; + }; + /* other clocks */ + }; + + # The clock consumer shall specify the desired clock-output of the clock + # controller as below by specifying output-id in its "clk" phandle cell. + # 2: uart + # 4: 32-bit timer + # 7: UHS-I/II + - | + serial@1e700010 { + compatible = "socionext,milbeaut-usio-uart"; + reg = <0x1e700010 0x10>; + interrupts = <0 141 0x4>, <0 149 0x4>; + interrupt-names = "rx", "tx"; + clocks = <&clk 2>; + }; + +... diff --git a/Documentation/devicetree/bindings/clock/qcom,turingcc.txt b/Documentation/devicetree/bindings/clock/qcom,turingcc.txt new file mode 100644 index 000000000000..126517de5f9a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,turingcc.txt @@ -0,0 +1,19 @@ +Qualcomm Turing Clock & Reset Controller Binding +------------------------------------------------ + +Required properties : +- compatible: shall contain "qcom,qcs404-turingcc". +- reg: shall contain base register location and length. +- clocks: ahb clock for the TuringCC +- #clock-cells: from common clock binding, shall contain 1. +- #reset-cells: from common reset binding, shall contain 1. + +Example: + turingcc: clock-controller@800000 { + compatible = "qcom,qcs404-turingcc"; + reg = <0x00800000 0x30000>; + clocks = <&gcc GCC_CDSP_CFG_AHB_CLK>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt index c655f28d5918..f7d48f23da44 100644 --- a/Documentation/devicetree/bindings/clock/qoriq-clock.txt +++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt @@ -39,6 +39,7 @@ Required properties: * "fsl,b4860-clockgen" * "fsl,ls1012a-clockgen" * "fsl,ls1021a-clockgen" + * "fsl,ls1028a-clockgen" * "fsl,ls1043a-clockgen" * "fsl,ls1046a-clockgen" * "fsl,ls1088a-clockgen" @@ -83,8 +84,8 @@ second cell is the clock index for the specified type. 1 cmux index (n in CLKCnCSR) 2 hwaccel index (n in CLKCGnHWACSR) 3 fman 0 for fm1, 1 for fm2 - 4 platform pll 0=pll, 1=pll/2, 2=pll/3, 3=pll/4 - 4=pll/5, 5=pll/6, 6=pll/7, 7=pll/8 + 4 platform pll n=pll/(n+1). For example, when n=1, + that means output_freq=PLL_freq/2. 5 coreclk must be 0 3. Example diff --git a/Documentation/devicetree/bindings/clock/sifive/fu540-prci.txt b/Documentation/devicetree/bindings/clock/sifive/fu540-prci.txt new file mode 100644 index 000000000000..349808f4fb8c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sifive/fu540-prci.txt @@ -0,0 +1,46 @@ +SiFive FU540 PRCI bindings + +On the FU540 family of SoCs, most system-wide clock and reset integration +is via the PRCI IP block. + +Required properties: +- compatible: Should be "sifive,<chip>-prci". Only one value is + supported: "sifive,fu540-c000-prci" +- reg: Should describe the PRCI's register target physical address region +- clocks: Should point to the hfclk device tree node and the rtcclk + device tree node. The RTC clock here is not a time-of-day clock, + but is instead a high-stability clock source for system timers + and cycle counters. +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock via the clock ID +macros defined in include/dt-bindings/clock/sifive-fu540-prci.h. +These macros begin with PRCI_CLK_. + +The hfclk and rtcclk nodes are required, and represent physical +crystals or resonators located on the PCB. These nodes should be present +underneath /, rather than /soc. + +Examples: + +/* under /, in PCB-specific DT data */ +hfclk: hfclk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <33333333>; + clock-output-names = "hfclk"; +}; +rtcclk: rtcclk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <1000000>; + clock-output-names = "rtcclk"; +}; + +/* under /soc, in SoC-specific DT data */ +prci: clock-controller@10000000 { + compatible = "sifive,fu540-c000-prci"; + reg = <0x0 0x10000000 0x0 0x1000>; + clocks = <&hfclk>, <&rtcclk>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt index b240121d2ac9..cfa04b614d8a 100644 --- a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt +++ b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt @@ -11,6 +11,8 @@ Required properties: "st,stm32f42xx-rcc" "st,stm32f469-rcc" "st,stm32f746-rcc" + "st,stm32f769-rcc" + - reg: should be register base and length as documented in the datasheet - #reset-cells: 1, see below @@ -102,6 +104,10 @@ The secondary index is bound with the following magic numbers: 28 CLK_I2C3 29 CLK_I2C4 30 CLK_LPTIMER (LPTimer1 clock) + 31 CLK_PLL_SRC + 32 CLK_DFSDM1 + 33 CLK_ADFSDM1 + 34 CLK_F769_DSI ) Example: diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt b/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt index bf4a18047309..3a50a7862cf3 100644 --- a/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt @@ -37,6 +37,7 @@ Required properties: - GXL (S905X, S905D) : "amlogic,meson-gxl-dw-hdmi" - GXM (S912) : "amlogic,meson-gxm-dw-hdmi" followed by the common "amlogic,meson-gx-dw-hdmi" + - G12A (S905X2, S905Y2, S905D2) : "amlogic,meson-g12a-dw-hdmi" - reg: Physical base address and length of the controller's registers. - interrupts: The HDMI interrupt number - clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks, @@ -66,6 +67,9 @@ corresponding to each HDMI output and input. S905X (GXL) VENC Input TMDS Output S905D (GXL) VENC Input TMDS Output S912 (GXM) VENC Input TMDS Output + S905X2 (G12A) VENC Input TMDS Output + S905Y2 (G12A) VENC Input TMDS Output + S905D2 (G12A) VENC Input TMDS Output Example: diff --git a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt index c65fd7a7467c..be40a780501c 100644 --- a/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt +++ b/Documentation/devicetree/bindings/display/amlogic,meson-vpu.txt @@ -57,18 +57,18 @@ Required properties: - GXL (S905X, S905D) : "amlogic,meson-gxl-vpu" - GXM (S912) : "amlogic,meson-gxm-vpu" followed by the common "amlogic,meson-gx-vpu" + - G12A (S905X2, S905Y2, S905D2) : "amlogic,meson-g12a-vpu" - reg: base address and size of he following memory-mapped regions : - vpu - hhi - - dmc - reg-names: should contain the names of the previous memory regions - interrupts: should contain the VENC Vsync interrupt number +- amlogic,canvas: phandle to canvas provider node as described in the file + ../soc/amlogic/amlogic,canvas.txt Optional properties: - power-domains: Optional phandle to associated power domain as described in the file ../power/power_domain.txt -- amlogic,canvas: phandle to canvas provider node as described in the file - ../soc/amlogic/amlogic,canvas.txt Required nodes: @@ -84,6 +84,9 @@ corresponding to each VPU output. S905X (GXL) CVBS VDAC HDMI-TX S905D (GXL) CVBS VDAC HDMI-TX S912 (GXM) CVBS VDAC HDMI-TX + S905X2 (G12A) CVBS VDAC HDMI-TX + S905Y2 (G12A) CVBS VDAC HDMI-TX + S905D2 (G12A) CVBS VDAC HDMI-TX Example: diff --git a/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt index 54d7e31525ec..5ff4f64ef8e8 100644 --- a/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt +++ b/Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt @@ -6,15 +6,32 @@ Required properties: Optional properties: - powerdown-gpios: power-down gpio -- reg: I2C address. If and only if present the device node - should be placed into the i2c controller node where the - tfp410 i2c is connected to. +- reg: I2C address. If and only if present the device node should be placed + into the I2C controller node where the TFP410 I2C is connected to. +- ti,deskew: data de-skew in 350ps increments, from -4 to +3, as configured + through th DK[3:1] pins. This property shall be present only if the TFP410 + is not connected through I2C. Required nodes: -- Video port 0 for DPI input [1]. -- Video port 1 for DVI output [1]. -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt +This device has two video ports. Their connections are modeled using the OF +graph bindings specified in [1]. Each port node shall have a single endpoint. + +- Port 0 is the DPI input port. Its endpoint subnode shall contain a + pclk-sample and bus-width property and a remote-endpoint property as specified + in [1]. + - If pclk-sample is not defined, pclk-sample = 0 should be assumed for + backward compatibility. + - If bus-width is not defined then bus-width = 24 should be assumed for + backward compatibility. + bus-width = 24: 24 data lines are connected and single-edge mode + bus-width = 12: 12 data lines are connected and dual-edge mode + +- Port 1 is the DVI output port. Its endpoint subnode shall contain a + remote-endpoint property is specified in [1]. + +[1] Documentation/devicetree/bindings/media/video-interfaces.txt + Example ------- @@ -22,6 +39,7 @@ Example tfp410: encoder@0 { compatible = "ti,tfp410"; powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>; + ti,deskew = <4>; ports { #address-cells = <1>; @@ -31,6 +49,8 @@ tfp410: encoder@0 { reg = <0>; tfp410_in: endpoint@0 { + pclk-sample = <1>; + bus-width = <24>; remote-endpoint = <&dpi_out>; }; }; diff --git a/Documentation/devicetree/bindings/display/msm/gmu.txt b/Documentation/devicetree/bindings/display/msm/gmu.txt index 3439b38e60f2..90af5b0a56a9 100644 --- a/Documentation/devicetree/bindings/display/msm/gmu.txt +++ b/Documentation/devicetree/bindings/display/msm/gmu.txt @@ -24,7 +24,10 @@ Required properties: * "cxo" * "axi" * "mnoc" -- power-domains: should be <&clock_gpucc GPU_CX_GDSC> +- power-domains: should be: + <&clock_gpucc GPU_CX_GDSC> + <&clock_gpucc GPU_GX_GDSC> +- power-domain-names: Matching names for the power domains - iommus: phandle to the adreno iommu - operating-points-v2: phandle to the OPP operating points @@ -51,7 +54,10 @@ Example: <&gcc GCC_GPU_MEMNOC_GFX_CLK>; clock-names = "gmu", "cxo", "axi", "memnoc"; - power-domains = <&gpucc GPU_CX_GDSC>; + power-domains = <&gpucc GPU_CX_GDSC>, + <&gpucc GPU_GX_GDSC>; + power-domain-names = "cx", "gx"; + iommus = <&adreno_smmu 5>; operating-points-v2 = <&gmu_opp_table>; diff --git a/Documentation/devicetree/bindings/display/msm/gpu.txt b/Documentation/devicetree/bindings/display/msm/gpu.txt index aad1aef682f7..2b8fd26c43b0 100644 --- a/Documentation/devicetree/bindings/display/msm/gpu.txt +++ b/Documentation/devicetree/bindings/display/msm/gpu.txt @@ -22,9 +22,14 @@ Required properties: - qcom,adreno-630.2 - iommus: optional phandle to an adreno iommu instance - operating-points-v2: optional phandle to the OPP operating points +- interconnects: optional phandle to an interconnect provider. See + ../interconnect/interconnect.txt for details. - qcom,gmu: For GMU attached devices a phandle to the GMU device that will control the power for the GPU. Applicable targets: - qcom,adreno-630.2 +- zap-shader: For a5xx and a6xx devices this node contains a memory-region that + points to reserved memory to store the zap shader that can be used to help + bring the GPU out of secure mode. Example 3xx/4xx/a5xx: @@ -70,6 +75,12 @@ Example a6xx (with GMU): operating-points-v2 = <&gpu_opp_table>; + interconnects = <&rsc_hlos MASTER_GFX3D &rsc_hlos SLAVE_EBI1>; + qcom,gmu = <&gmu>; + + zap-shader { + memory-region = <&zap_shader_region>; + }; }; }; diff --git a/Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt b/Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt new file mode 100644 index 000000000000..82caa7b65ae8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/feiyang,fy07024di26a30d.txt @@ -0,0 +1,20 @@ +Feiyang FY07024DI26A30-D 7" MIPI-DSI LCD Panel + +Required properties: +- compatible: must be "feiyang,fy07024di26a30d" +- reg: DSI virtual channel used by that screen +- avdd-supply: analog regulator dc1 switch +- dvdd-supply: 3v3 digital regulator +- reset-gpios: a GPIO phandle for the reset pin + +Optional properties: +- backlight: phandle for the backlight control. + +panel@0 { + compatible = "feiyang,fy07024di26a30d"; + reg = <0>; + avdd-supply = <®_dc1sw>; + dvdd-supply = <®_dldo2>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ + backlight = <&backlight>; +}; diff --git a/Documentation/devicetree/bindings/display/panel/innolux,p079zca.txt b/Documentation/devicetree/bindings/display/panel/innolux,p079zca.txt index d0f55161579a..3ab8c7412cf6 100644 --- a/Documentation/devicetree/bindings/display/panel/innolux,p079zca.txt +++ b/Documentation/devicetree/bindings/display/panel/innolux,p079zca.txt @@ -12,7 +12,7 @@ Optional properties: Example: &mipi_dsi { - panel { + panel@0 { compatible = "innolux,p079zca"; reg = <0>; power-supply = <...>; diff --git a/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.txt b/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.txt index 595d9dfeffd3..d1cab3a8f0fb 100644 --- a/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.txt +++ b/Documentation/devicetree/bindings/display/panel/innolux,p097pfg.txt @@ -13,7 +13,7 @@ Optional properties: Example: &mipi_dsi { - panel { + panel@0 { compatible = "innolux,p079zca"; reg = <0>; avdd-supply = <...>; diff --git a/Documentation/devicetree/bindings/display/panel/kingdisplay,kd097d04.txt b/Documentation/devicetree/bindings/display/panel/kingdisplay,kd097d04.txt index 164a5fa236da..cfefff688614 100644 --- a/Documentation/devicetree/bindings/display/panel/kingdisplay,kd097d04.txt +++ b/Documentation/devicetree/bindings/display/panel/kingdisplay,kd097d04.txt @@ -12,7 +12,7 @@ Optional properties: Example: &mipi_dsi { - panel { + panel@0 { compatible = "kingdisplay,kd097d04"; reg = <0>; power-supply = <...>; diff --git a/Documentation/devicetree/bindings/display/panel/lg,acx467akm-7.txt b/Documentation/devicetree/bindings/display/panel/lg,acx467akm-7.txt new file mode 100644 index 000000000000..fc1e1b325e49 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,acx467akm-7.txt @@ -0,0 +1,7 @@ +LG ACX467AKM-7 4.95" 1080×1920 LCD Panel + +Required properties: +- compatible: must be "lg,acx467akm-7" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/osddisplays,osd070t1718-19ts.txt b/Documentation/devicetree/bindings/display/panel/osddisplays,osd070t1718-19ts.txt new file mode 100644 index 000000000000..e57883ccdf2f --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/osddisplays,osd070t1718-19ts.txt @@ -0,0 +1,12 @@ +OSD Displays OSD070T1718-19TS 7" WVGA TFT LCD panel + +Required properties: +- compatible: shall be "osddisplays,osd070t1718-19ts" +- power-supply: see simple-panel.txt + +Optional properties: +- backlight: see simple-panel.txt + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. No other simple-panel properties than +the ones specified herein are valid. diff --git a/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt b/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt new file mode 100644 index 000000000000..1b5763200cf6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/rocktech,jh057n00900.txt @@ -0,0 +1,18 @@ +Rocktech jh057n00900 5.5" 720x1440 TFT LCD panel + +Required properties: +- compatible: should be "rocktech,jh057n00900" +- reg: DSI virtual channel of the peripheral +- reset-gpios: panel reset gpio +- backlight: phandle of the backlight device attached to the panel + +Example: + + &mipi_dsi { + panel@0 { + compatible = "rocktech,jh057n00900"; + reg = <0>; + backlight = <&backlight>; + reset-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/ronbo,rb070d30.yaml b/Documentation/devicetree/bindings/display/panel/ronbo,rb070d30.yaml new file mode 100644 index 000000000000..0e7987f1cdb7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ronbo,rb070d30.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR X11) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/panel/ronbo,rb070d30.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ronbo RB070D30 DSI Display Panel + +maintainers: + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + compatible: + const: ronbo,rb070d30 + + reg: + description: MIPI-DSI virtual channel + + power-gpios: + description: GPIO used for the power pin + maxItems: 1 + + reset-gpios: + description: GPIO used for the reset pin + maxItems: 1 + + shlr-gpios: + description: GPIO used for the shlr pin (horizontal flip) + maxItems: 1 + + updn-gpios: + description: GPIO used for the updn pin (vertical flip) + maxItems: 1 + + vcc-lcd-supply: + description: Power regulator + + backlight: + description: Backlight used by the panel + $ref: "/schemas/types.yaml#/definitions/phandle" + +required: + - compatible + - power-gpios + - reg + - reset-gpios + - shlr-gpios + - updn-gpios + - vcc-lcd-supply + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/display/panel/tpo,td028ttec1.txt b/Documentation/devicetree/bindings/display/panel/tpo,td028ttec1.txt index ed34253d9fb1..898e06ecf4ef 100644 --- a/Documentation/devicetree/bindings/display/panel/tpo,td028ttec1.txt +++ b/Documentation/devicetree/bindings/display/panel/tpo,td028ttec1.txt @@ -6,6 +6,7 @@ Required properties: Optional properties: - label: a symbolic name for the panel +- backlight: phandle of the backlight device Required nodes: - Video port for DPI input @@ -21,6 +22,7 @@ lcd-panel: td028ttec1@0 { spi-cpha; label = "lcd"; + backlight = <&backlight>; port { lcd_in: endpoint { remote-endpoint = <&dpi_out>; diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.txt new file mode 100644 index 000000000000..d1ad31bca8d9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3066-hdmi.txt @@ -0,0 +1,72 @@ +Rockchip specific extensions for rk3066 HDMI +============================================ + +Required properties: +- compatible: + "rockchip,rk3066-hdmi"; +- reg: + Physical base address and length of the controller's registers. +- clocks, clock-names: + Phandle to HDMI controller clock, name should be "hclk". +- interrupts: + HDMI interrupt number. +- power-domains: + Phandle to the RK3066_PD_VIO power domain. +- rockchip,grf: + This soc uses GRF regs to switch the HDMI TX input between vop0 and vop1. +- ports: + Contains one port node with two endpoints, numbered 0 and 1, + connected respectively to vop0 and vop1. + Contains one port node with one endpoint + connected to a hdmi-connector node. +- pinctrl-0, pinctrl-name: + Switch the iomux for the HPD/I2C pins to HDMI function. + +Example: + hdmi: hdmi@10116000 { + compatible = "rockchip,rk3066-hdmi"; + reg = <0x10116000 0x2000>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_HDMI>; + clock-names = "hclk"; + power-domains = <&power RK3066_PD_VIO>; + rockchip,grf = <&grf>; + pinctrl-names = "default"; + pinctrl-0 = <&hdmii2c_xfer>, <&hdmi_hpd>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + hdmi_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + hdmi_in_vop0: endpoint@0 { + reg = <0>; + remote-endpoint = <&vop0_out_hdmi>; + }; + hdmi_in_vop1: endpoint@1 { + reg = <1>; + remote-endpoint = <&vop1_out_hdmi>; + }; + }; + hdmi_out: port@1 { + reg = <1>; + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; + }; + }; + }; + +&pinctrl { + hdmi { + hdmi_hpd: hdmi-hpd { + rockchip,pins = <0 RK_PA0 1 &pcfg_pull_default>; + }; + hdmii2c_xfer: hdmii2c-xfer { + rockchip,pins = <0 RK_PA1 1 &pcfg_pull_none>, + <0 RK_PA2 1 &pcfg_pull_none>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/ste,mcde.txt b/Documentation/devicetree/bindings/display/ste,mcde.txt new file mode 100644 index 000000000000..4c33c692bd5f --- /dev/null +++ b/Documentation/devicetree/bindings/display/ste,mcde.txt @@ -0,0 +1,104 @@ +ST-Ericsson Multi Channel Display Engine MCDE + +The ST-Ericsson MCDE is a display controller with support for compositing +and displaying several channels memory resident graphics data on DSI or +LCD displays or bridges. It is used in the ST-Ericsson U8500 platform. + +Required properties: + +- compatible: must be: + "ste,mcde" +- reg: register base for the main MCDE control registers, should be + 0x1000 in size +- interrupts: the interrupt line for the MCDE +- epod-supply: a phandle to the EPOD regulator +- vana-supply: a phandle to the analog voltage regulator +- clocks: an array of the MCDE clocks in this strict order: + MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI + (HDMI clock), DSI0ESCLK (DSI0 energy save clock), + DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy + save clock) +- clock-names: must be the following array: + "mcde", "lcd", "hdmi" + to match the required clock inputs above. +- #address-cells: should be <1> (for the DSI hosts that will be children) +- #size-cells: should be <1> (for the DSI hosts that will be children) +- ranges: this should always be stated + +Required subnodes: + +The devicetree must specify subnodes for the DSI host adapters. +These must have the following characteristics: + +- compatible: must be: + "ste,mcde-dsi" +- reg: must specify the register range for the DSI host +- vana-supply: phandle to the VANA voltage regulator +- clocks: phandles to the high speed and low power (energy save) clocks + the high speed clock is not present on the third (dsi2) block, so it + should only have the "lp" clock +- clock-names: "hs" for the high speed clock and "lp" for the low power + (energy save) clock +- #address-cells: should be <1> +- #size-cells: should be <0> + +Display panels and bridges will appear as children on the DSI hosts, and +the displays are connected to the DSI hosts using the common binding +for video transmitter interfaces; see +Documentation/devicetree/bindings/media/video-interfaces.txt + +If a DSI host is unused (not connected) it will have no children defined. + +Example: + +mcde@a0350000 { + compatible = "ste,mcde"; + reg = <0xa0350000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + epod-supply = <&db8500_b2r2_mcde_reg>; + vana-supply = <&ab8500_ldo_ana_reg>; + clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */ + <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */ + <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */ + clock-names = "mcde", "lcd", "hdmi"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dsi0: dsi@a0351000 { + compatible = "ste,mcde-dsi"; + reg = <0xa0351000 0x1000>; + vana-supply = <&ab8500_ldo_ana_reg>; + clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>; + clock-names = "hs", "lp"; + #address-cells = <1>; + #size-cells = <0>; + + panel { + compatible = "samsung,s6d16d0"; + reg = <0>; + vdd1-supply = <&ab8500_ldo_aux1_reg>; + reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + }; + + }; + dsi1: dsi@a0352000 { + compatible = "ste,mcde-dsi"; + reg = <0xa0352000 0x1000>; + vana-supply = <&ab8500_ldo_ana_reg>; + clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>; + clock-names = "hs", "lp"; + #address-cells = <1>; + #size-cells = <0>; + }; + dsi2: dsi@a0353000 { + compatible = "ste,mcde-dsi"; + reg = <0xa0353000 0x1000>; + vana-supply = <&ab8500_ldo_ana_reg>; + /* This DSI port only has the Low Power / Energy Save clock */ + clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>; + clock-names = "lp"; + #address-cells = <1>; + #size-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt index 47cb1d14b690..b38ee732efa9 100644 --- a/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt +++ b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt @@ -18,7 +18,6 @@ Required properties for adi,channels sub-node: Required channel sub-node properties: - reg: Which channel this node refers to. - - adi,length-width: Width of the DMA transfer length register. - adi,source-bus-width, adi,destination-bus-width: Width of the source or destination bus in bits. - adi,source-bus-type, @@ -28,7 +27,8 @@ Required channel sub-node properties: 1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface 2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface -Optional channel properties: +Deprecated optional channel properties: + - adi,length-width: Width of the DMA transfer length register. - adi,cyclic: Must be set if the channel supports hardware cyclic DMA transfers. - adi,2d: Must be set if the channel supports hardware 2D DMA transfers. diff --git a/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt b/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt index 2f35b047f772..245d3063715c 100644 --- a/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt +++ b/Documentation/devicetree/bindings/dma/nvidia,tegra210-adma.txt @@ -4,7 +4,9 @@ The Tegra Audio DMA controller that is used for transferring data between system memory and the Audio Processing Engine (APE). Required properties: -- compatible: Must be "nvidia,tegra210-adma". +- compatible: Should contain one of the following: + - "nvidia,tegra210-adma": for Tegra210 + - "nvidia,tegra186-adma": for Tegra186 and Tegra194 - reg: Should contain DMA registers location and length. This should be a single entry that includes all of the per-channel registers in one contiguous bank. diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt index 0e456bbc1213..22aead844d0f 100644 --- a/Documentation/devicetree/bindings/eeprom/at24.txt +++ b/Documentation/devicetree/bindings/eeprom/at24.txt @@ -50,6 +50,7 @@ Required properties: "nxp,se97b" - the fallback is "atmel,24c02", "renesas,r1ex24002" - the fallback is "atmel,24c02" + "renesas,r1ex24016" - the fallback is "atmel,24c16" "renesas,r1ex24128" - the fallback is "atmel,24c128" "rohm,br24t01" - the fallback is "atmel,24c01" diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.txt b/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.txt new file mode 100644 index 000000000000..b8be9dbc68b4 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.txt @@ -0,0 +1,92 @@ +ARM Mali Bifrost GPU +==================== + +Required properties: + +- compatible : + * Since Mali Bifrost GPU model/revision is fully discoverable by reading + some determined registers, must contain the following: + + "arm,mali-bifrost" + * which must be preceded by one of the following vendor specifics: + + "amlogic,meson-g12a-mali" + +- reg : Physical base address of the device and length of the register area. + +- interrupts : Contains the three IRQ lines required by Mali Bifrost devices, + in the following defined order. + +- interrupt-names : Contains the names of IRQ resources in this exact defined + order: "job", "mmu", "gpu". + +Optional properties: + +- clocks : Phandle to clock for the Mali Bifrost device. + +- mali-supply : Phandle to regulator for the Mali device. Refer to + Documentation/devicetree/bindings/regulator/regulator.txt for details. + +- operating-points-v2 : Refer to Documentation/devicetree/bindings/opp/opp.txt + for details. + +- resets : Phandle of the GPU reset line. + +Vendor-specific bindings +------------------------ + +The Mali GPU is integrated very differently from one SoC to +another. In order to accommodate those differences, you have the option +to specify one more vendor-specific compatible, among: + +- "amlogic,meson-g12a-mali" + Required properties: + - resets : Should contain phandles of : + + GPU reset line + + GPU APB glue reset line + +Example for a Mali-G31: + +gpu@ffa30000 { + compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost"; + reg = <0xffe40000 0x10000>; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "job", "mmu", "gpu"; + clocks = <&clk CLKID_MALI>; + mali-supply = <&vdd_gpu>; + operating-points-v2 = <&gpu_opp_table>; + resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>; +}; + +gpu_opp_table: opp_table0 { + compatible = "operating-points-v2"; + + opp@533000000 { + opp-hz = /bits/ 64 <533000000>; + opp-microvolt = <1250000>; + }; + opp@450000000 { + opp-hz = /bits/ 64 <450000000>; + opp-microvolt = <1150000>; + }; + opp@400000000 { + opp-hz = /bits/ 64 <400000000>; + opp-microvolt = <1125000>; + }; + opp@350000000 { + opp-hz = /bits/ 64 <350000000>; + opp-microvolt = <1075000>; + }; + opp@266000000 { + opp-hz = /bits/ 64 <266000000>; + opp-microvolt = <1025000>; + }; + opp@160000000 { + opp-hz = /bits/ 64 <160000000>; + opp-microvolt = <925000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <912500>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpu/aspeed-gfx.txt b/Documentation/devicetree/bindings/gpu/aspeed-gfx.txt new file mode 100644 index 000000000000..958bdf962339 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/aspeed-gfx.txt @@ -0,0 +1,41 @@ +Device tree configuration for the GFX display device on the ASPEED SoCs + +Required properties: + - compatible + * Must be one of the following: + + aspeed,ast2500-gfx + + aspeed,ast2400-gfx + * In addition, the ASPEED pinctrl bindings require the 'syscon' property to + be present + + - reg: Physical base address and length of the GFX registers + + - interrupts: interrupt number for the GFX device + + - clocks: clock number used to generate the pixel clock + + - resets: reset line that must be released to use the GFX device + + - memory-region: + Phandle to a memory region to allocate from, as defined in + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt + + +Example: + +gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; + reg-io-width = <4>; + clocks = <&syscon ASPEED_CLK_GATE_D1CLK>; + resets = <&syscon ASPEED_RESET_CRT1>; + interrupts = <0x19>; + memory-region = <&gfx_memory>; +}; + +gfx_memory: framebuffer { + size = <0x01000000>; + alignment = <0x01000000>; + compatible = "shared-dma-pool"; + reusable; +}; diff --git a/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt index c907aa8dd755..b2df82b44625 100644 --- a/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt +++ b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt @@ -6,15 +6,20 @@ For V3D 2.x, see brcm,bcm-vc4.txt. Required properties: - compatible: Should be "brcm,7268-v3d" or "brcm,7278-v3d" - reg: Physical base addresses and lengths of the register areas -- reg-names: Names for the register areas. The "hub", "bridge", and "core0" +- reg-names: Names for the register areas. The "hub" and "core0" register areas are always required. The "gca" register area - is required if the GCA cache controller is present. + is required if the GCA cache controller is present. The + "bridge" register area is required if an external reset + controller is not present. - interrupts: The interrupt numbers. The first interrupt is for the hub, - while the following interrupts are for the cores. + while the following interrupts are separate interrupt lines + for the cores (if they don't share the hub's interrupt). See bindings/interrupt-controller/interrupts.txt Optional properties: - clocks: The core clock the unit runs on +- resets: The reset line for v3d, if not using a mapping of the bridge + See bindings/reset/reset.txt v3d { compatible = "brcm,7268-v3d"; diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt index 81f982ccca31..d12cc33cca6c 100644 --- a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt @@ -3,15 +3,12 @@ Broadcom iProc I2C controller Required properties: - compatible: - Must be "brcm,iproc-i2c" + Must be "brcm,iproc-i2c" or "brcm,iproc-nic-i2c" - reg: Define the base and range of the I/O address space that contain the iProc I2C controller registers -- interrupts: - Should contain the I2C interrupt - - clock-frequency: This is the I2C bus clock. Need to be either 100000 or 400000 @@ -21,6 +18,18 @@ Required properties: - #size-cells: Always 0 +Optional properties: + +- interrupts: + Should contain the I2C interrupt. For certain revisions of the I2C + controller, I2C interrupt is unwired to the interrupt controller. In such + case, this property should be left unspecified, and driver will fall back + to polling mode + +- brcm,ape-hsls-addr-mask: + Required for "brcm,iproc-nic-i2c". Host view of address mask into the + 'APE' co-processor. Value must be unsigned, 32-bit + Example: i2c0: i2c@18008000 { compatible = "brcm,iproc-i2c"; diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt index 3e4bcc2fb6f7..08be4d3846e5 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -6,12 +6,21 @@ Required properties : or "mscc,ocelot-i2c" with "snps,designware-i2c" for fallback - reg : Offset and length of the register set for the device - interrupts : <IRQ> where IRQ is the interrupt number. + - clocks : phandles for the clocks, see the description of clock-names below. + The phandle for the "ic_clk" clock is required. The phandle for the "pclk" + clock is optional. If a single clock is specified but no clock-name, it is + the "ic_clk" clock. If both clocks are listed, the "ic_clk" must be first. Recommended properties : - clock-frequency : desired I2C bus clock frequency in Hz. Optional properties : + + - clock-names : Contains the names of the clocks: + "ic_clk", for the core clock used to generate the external I2C clock. + "pclk", the interface clock, required for register access. + - reg : for "mscc,ocelot-i2c", a second register set to configure the SDA hold time, named ICPU_CFG:TWI_DELAY in the datasheet. diff --git a/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt b/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt index ee4c32454198..68f6d73a8b73 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt @@ -12,13 +12,16 @@ Required properties: "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623 "mediatek,mt7629-i2c", "mediatek,mt2712-i2c": for MediaTek MT7629 "mediatek,mt8173-i2c": for MediaTek MT8173 + "mediatek,mt8183-i2c": for MediaTek MT8183 + "mediatek,mt8516-i2c", "mediatek,mt2712-i2c": for MediaTek MT8516 - reg: physical base address of the controller and dma base, length of memory mapped region. - interrupts: interrupt number to the cpu. - clock-div: the fixed value for frequency divider of clock source in i2c module. Each IC may be different. - clocks: clock name from clock manager - - clock-names: Must include "main" and "dma", if enable have-pmic need include + - clock-names: Must include "main" and "dma", "arb" is for multi-master that + one bus has more than two i2c controllers, if enable have-pmic need include "pmic" extra. Optional properties: diff --git a/Documentation/devicetree/bindings/i2c/i2c-riic.txt b/Documentation/devicetree/bindings/i2c/i2c-riic.txt index 0bcc4716c319..e26fe3ad86a9 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-riic.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-riic.txt @@ -1,7 +1,10 @@ Device tree configuration for Renesas RIIC driver Required properties: -- compatible : "renesas,riic-<soctype>". "renesas,riic-rz" as fallback +- compatible : + "renesas,riic-r7s72100" if the device is a part of a R7S72100 SoC. + "renesas,riic-r7s9210" if the device is a part of a R7S9210 SoC. + "renesas,riic-rz" for a generic RZ/A compatible device. - reg : address start and address range size of device - interrupts : 8 interrupts (TEI, RI, TI, SPI, STI, NAKI, ALI, TMOI) - clock-frequency : frequency of bus clock in Hz diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt index 69240e189b01..f334738f7a35 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -1,11 +1,11 @@ * I2C controller embedded in STMicroelectronics STM32 I2C platform -Required properties : -- compatible : Must be one of the following +Required properties: +- compatible: Must be one of the following - "st,stm32f4-i2c" - "st,stm32f7-i2c" -- reg : Offset and length of the register set for the device -- interrupts : Must contain the interrupt id for I2C event and then the +- reg: Offset and length of the register set for the device +- interrupts: Must contain the interrupt id for I2C event and then the interrupt id for I2C error. - resets: Must contain the phandle to the reset controller. - clocks: Must contain the input clock of the I2C instance. @@ -14,25 +14,26 @@ Required properties : - #address-cells = <1>; - #size-cells = <0>; -Optional properties : -- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, +Optional properties: +- clock-frequency: Desired I2C bus clock frequency in Hz. If not specified, the default 100 kHz frequency will be used. For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are 100000 and 400000. - For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported, - possible values are 100000, 400000 and 1000000. -- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board - (default: 25) -- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board - (default: 10) + For STM32F7, STM32H7 and STM32MP1 SoCs, Standard-mode, Fast-mode and Fast-mode + Plus are supported, possible values are 100000, 400000 and 1000000. +- i2c-scl-rising-time-ns: I2C SCL Rising time for the board (default: 25) + For STM32F7, STM32H7 and STM32MP1 only. +- i2c-scl-falling-time-ns: I2C SCL Falling time for the board (default: 10) + For STM32F7, STM32H7 and STM32MP1 only. I2C Timings are derived from these 2 values -- st,syscfg-fmp: Only for STM32F7, use to set Fast Mode Plus bit within SYSCFG - whether Fast Mode Plus speed is selected by slave. - 1st cell : phandle to syscfg - 2nd cell : register offset within SYSCFG - 3rd cell : register bitmask for FMP bit +- st,syscfg-fmp: Use to set Fast Mode Plus bit within SYSCFG when Fast Mode + Plus speed is selected by slave. + 1st cell: phandle to syscfg + 2nd cell: register offset within SYSCFG + 3rd cell: register bitmask for FMP bit + For STM32F7, STM32H7 and STM32MP1 only. -Example : +Example: i2c@40005400 { compatible = "st,stm32f4-i2c"; diff --git a/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt b/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt index d3e380ad712d..627bb533eff7 100644 --- a/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt +++ b/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt @@ -1,7 +1,11 @@ * NXP PCF85063 Real Time Clock Required properties: -- compatible: Should contain "nxp,pcf85063". +- compatible: Should one of contain: + "nxp,pcf85063", + "nxp,pcf85063a", + "nxp,pcf85063tp", + "microcrystal,rv8263" - reg: I2C address for chip. Optional property: diff --git a/Documentation/devicetree/bindings/rtc/rtc-aspeed.txt b/Documentation/devicetree/bindings/rtc/rtc-aspeed.txt new file mode 100644 index 000000000000..2e956b3dc276 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-aspeed.txt @@ -0,0 +1,22 @@ +ASPEED BMC RTC +============== + +Required properties: + - compatible: should be one of the following + * aspeed,ast2400-rtc for the ast2400 + * aspeed,ast2500-rtc for the ast2500 + * aspeed,ast2600-rtc for the ast2600 + + - reg: physical base address of the controller and length of memory mapped + region + + - interrupts: The interrupt number + +Example: + + rtc@1e781000 { + compatible = "aspeed,ast2400-rtc"; + reg = <0x1e781000 0x18>; + interrupts = <22>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt index f4687c68c08c..a97fc6a9a75e 100644 --- a/Documentation/devicetree/bindings/rtc/rtc.txt +++ b/Documentation/devicetree/bindings/rtc/rtc.txt @@ -69,3 +69,4 @@ ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC sii,s35390a 2-wire CMOS real-time clock whwave,sd3078 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +xircom,x1205 Xircom X1205 I2C RTC diff --git a/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt b/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt index 4248b662deff..229ad1392cdc 100644 --- a/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt +++ b/Documentation/devicetree/bindings/sound/adi,axi-i2s.txt @@ -1,5 +1,8 @@ ADI AXI-I2S controller +The core can be generated with transmit (playback), only receive +(capture) or both directions enabled. + Required properties: - compatible : Must be "adi,axi-i2s-1.00.a" - reg : Must contain I2S core's registers location and length @@ -9,8 +12,8 @@ Required properties: - clock-names : "axi" for the clock to the AXI interface, "ref" for the sample rate reference clock. - dmas: Pairs of phandle and specifier for the DMA channels that are used by - the core. The core expects two dma channels, one for transmit and one for - receive. + the core. The core expects two dma channels if both transmit and receive are + enabled, one channel otherwise. - dma-names : "tx" for the transmit channel, "rx" for the receive channel. For more details on the 'dma', 'dma-names', 'clock' and 'clock-names' properties diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt index 3dfc2515e5c6..4330fc9dca6d 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-fifo.txt @@ -2,7 +2,9 @@ Required properties: - compatible: 'amlogic,axg-toddr' or - 'amlogic,axg-frddr' + 'amlogic,axg-toddr' or + 'amlogic,g12a-frddr' or + 'amlogic,g12a-toddr' - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt specifier for the fifo. diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt index 5672d0bc5b16..73f473a9365f 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-pdm.txt @@ -1,7 +1,8 @@ * Amlogic Audio PDM input Required properties: -- compatible: 'amlogic,axg-pdm' +- compatible: 'amlogic,axg-pdm' or + 'amlogic,g12a-pdm' - reg: physical base address of the controller and length of memory mapped region. - clocks: list of clock phandle, one for each entry clock-names. diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt index 2e6cb7d9b202..0b82504fa419 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt @@ -1,7 +1,8 @@ * Amlogic Audio SPDIF Input Required properties: -- compatible: 'amlogic,axg-spdifin' +- compatible: 'amlogic,axg-spdifin' or + 'amlogic,g12a-spdifin' - interrupts: interrupt specifier for the spdif input. - clocks: list of clock phandle, one for each entry clock-names. - clock-names: should contain the following: diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt index 521c38ad89e7..826152730508 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifout.txt @@ -1,7 +1,8 @@ * Amlogic Audio SPDIF Output Required properties: -- compatible: 'amlogic,axg-spdifout' +- compatible: 'amlogic,axg-spdifout' or + 'amlogic,g12a-spdifout' - clocks: list of clock phandle, one for each entry clock-names. - clock-names: should contain the following: * "pclk" : peripheral clock. diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt index 1c1b7490554e..3b94a715a0b9 100644 --- a/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-formatters.txt @@ -2,7 +2,9 @@ Required properties: - compatible: 'amlogic,axg-tdmin' or - 'amlogic,axg-tdmout' + 'amlogic,axg-tdmout' or + 'amlogic,g12a-tdmin' or + 'amlogic,g12a-tdmout' - reg: physical base address of the controller and length of memory mapped region. - clocks: list of clock phandle, one for each entry clock-names. diff --git a/Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt new file mode 100644 index 000000000000..41ae2699f07a --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cirrus,lochnagar.txt @@ -0,0 +1,39 @@ +Cirrus Logic Lochnagar Audio Development Board + +Lochnagar is an evaluation and development board for Cirrus Logic +Smart CODEC and Amp devices. It allows the connection of most Cirrus +Logic devices on mini-cards, as well as allowing connection of +various application processor systems to provide a full evaluation +platform. Audio system topology, clocking and power can all be +controlled through the Lochnagar, allowing the device under test +to be used in a variety of possible use cases. + +This binding document describes the binding for the audio portion +of the driver. + +This binding must be part of the Lochnagar MFD binding: + [4] ../mfd/cirrus,lochnagar.txt + +Required properties: + + - compatible : One of the following strings: + "cirrus,lochnagar2-soundcard" + + - #sound-dai-cells : Must be set to 1. + + - clocks : Contains an entry for each entry in clock-names. + - clock-names : Must include the following clocks: + "mclk" Master clock source for the sound card, should normally + be set to LOCHNAGAR_SOUNDCARD_MCLK provided by the Lochnagar + clock driver. + +Example: + +lochnagar-sc { + compatible = "cirrus,lochnagar2-soundcard"; + + #sound-dai-cells = <1>; + + clocks = <&lochnagar_clk LOCHNAGAR_SOUNDCARD_MCLK>; + clock-names = "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/cs42l51.txt b/Documentation/devicetree/bindings/sound/cs42l51.txt index 4b5de33ce377..acbd68ddd2cb 100644 --- a/Documentation/devicetree/bindings/sound/cs42l51.txt +++ b/Documentation/devicetree/bindings/sound/cs42l51.txt @@ -1,6 +1,17 @@ CS42L51 audio CODEC +Required properties: + + - compatible : "cirrus,cs42l51" + + - reg : the I2C address of the device for I2C. + Optional properties: + - VL-supply, VD-supply, VA-supply, VAHP-supply: power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt. + + - reset-gpios : GPIO specification for the reset pin. If specified, it will be + deasserted before starting the communication with the codec. - clocks : a list of phandles + clock-specifiers, one for each entry in clock-names @@ -14,4 +25,9 @@ cs42l51: cs42l51@4a { reg = <0x4a>; clocks = <&mclk_prov>; clock-names = "MCLK"; + VL-supply = <®_audio>; + VD-supply = <®_audio>; + VA-supply = <®_audio>; + VAHP-supply = <®_audio>; + reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/sound/da7219.txt b/Documentation/devicetree/bindings/sound/da7219.txt index e9d0baeb94e2..add1caf26ac2 100644 --- a/Documentation/devicetree/bindings/sound/da7219.txt +++ b/Documentation/devicetree/bindings/sound/da7219.txt @@ -23,8 +23,8 @@ Optional properties: interrupt is to be used to wake system, otherwise "irq" should be used. - wakeup-source: Flag to indicate this device can wake system (suspend/resume). -- #clock-cells : Should be set to '<0>', only one clock source provided; -- clock-output-names : Name given for DAI clocks output; +- #clock-cells : Should be set to '<1>', two clock sources provided; +- clock-output-names : Names given for DAI clock outputs (WCLK & BCLK); - clocks : phandle and clock specifier for codec MCLK. - clock-names : Clock name string for 'clocks' attribute, should be "mclk". @@ -84,8 +84,8 @@ Example: VDDMIC-supply = <®_audio>; VDDIO-supply = <®_audio>; - #clock-cells = <0>; - clock-output-names = "dai-clks"; + #clock-cells = <1>; + clock-output-names = "dai-wclk", "dai-bclk"; clocks = <&clks 201>; clock-names = "mclk"; diff --git a/Documentation/devicetree/bindings/sound/fsl,audmix.txt b/Documentation/devicetree/bindings/sound/fsl,audmix.txt new file mode 100644 index 000000000000..840b7e0d6a63 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/fsl,audmix.txt @@ -0,0 +1,50 @@ +NXP Audio Mixer (AUDMIX). + +The Audio Mixer is a on-chip functional module that allows mixing of two +audio streams into a single audio stream. Audio Mixer has two input serial +audio interfaces. These are driven by two Synchronous Audio interface +modules (SAI). Each input serial interface carries 8 audio channels in its +frame in TDM manner. Mixer mixes audio samples of corresponding channels +from two interfaces into a single sample. Before mixing, audio samples of +two inputs can be attenuated based on configuration. The output of the +Audio Mixer is also a serial audio interface. Like input interfaces it has +the same TDM frame format. This output is used to drive the serial DAC TDM +interface of audio codec and also sent to the external pins along with the +receive path of normal audio SAI module for readback by the CPU. + +The output of Audio Mixer can be selected from any of the three streams + - serial audio input 1 + - serial audio input 2 + - mixed audio + +Mixing operation is independent of audio sample rate but the two audio +input streams must have same audio sample rate with same number of channels +in TDM frame to be eligible for mixing. + +Device driver required properties: +================================= + - compatible : Compatible list, contains "fsl,imx8qm-audmix" + + - reg : Offset and length of the register set for the device. + + - clocks : Must contain an entry for each entry in clock-names. + + - clock-names : Must include the "ipg" for register access. + + - power-domains : Must contain the phandle to AUDMIX power domain node + + - dais : Must contain a list of phandles to AUDMIX connected + DAIs. The current implementation requires two phandles + to SAI interfaces to be provided, the first SAI in the + list being used to route the AUDMIX output. + +Device driver configuration example: +====================================== + audmix: audmix@59840000 { + compatible = "fsl,imx8qm-audmix"; + reg = <0x0 0x59840000 0x0 0x10000>; + clocks = <&clk IMX8QXP_AUD_AUDMIX_IPG>; + clock-names = "ipg"; + power-domains = <&pd_audmix>; + dais = <&sai4>, <&sai5>; + }; diff --git a/Documentation/devicetree/bindings/sound/mchp-i2s-mcc.txt b/Documentation/devicetree/bindings/sound/mchp-i2s-mcc.txt new file mode 100644 index 000000000000..91ec83a6faed --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mchp-i2s-mcc.txt @@ -0,0 +1,43 @@ +* Microchip I2S Multi-Channel Controller + +Required properties: +- compatible: Should be "microchip,sam9x60-i2smcc". +- reg: Should be the physical base address of the controller and the + length of memory mapped region. +- interrupts: Should contain the interrupt for the controller. +- dmas: Should be one per channel name listed in the dma-names property, + as described in atmel-dma.txt and dma.txt files. +- dma-names: Identifier string for each DMA request line in the dmas property. + Two dmas have to be defined, "tx" and "rx". +- clocks: Must contain an entry for each entry in clock-names. + Please refer to clock-bindings.txt. +- clock-names: Should be one of each entry matching the clocks phandles list: + - "pclk" (peripheral clock) Required. + - "gclk" (generated clock) Optional (1). + +Optional properties: +- pinctrl-0: Should specify pin control groups used for this controller. +- princtrl-names: Should contain only one value - "default". + + +(1) : Only the peripheral clock is required. The generated clock is optional + and should be set mostly when Master Mode is required. + +Example: + + i2s@f001c000 { + compatible = "microchip,sam9x60-i2smcc"; + reg = <0xf001c000 0x100>; + interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(36))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(37))>; + dma-names = "tx", "rx"; + clocks = <&i2s_clk>, <&i2s_gclk>; + clock-names = "pclk", "gclk"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2s_default>; + }; diff --git a/Documentation/devicetree/bindings/sound/mt8183-da7219-max98357.txt b/Documentation/devicetree/bindings/sound/mt8183-da7219-max98357.txt new file mode 100644 index 000000000000..92ac86f83822 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt8183-da7219-max98357.txt @@ -0,0 +1,15 @@ +MT8183 with MT6358, DA7219 and MAX98357 CODECS + +Required properties: +- compatible : "mediatek,mt8183_da7219_max98357" +- mediatek,headset-codec: the phandles of da7219 codecs +- mediatek,platform: the phandle of MT8183 ASoC platform + +Example: + + sound { + compatible = "mediatek,mt8183_da7219_max98357"; + mediatek,headset-codec = <&da7219>; + mediatek,platform = <&afe>; + }; + diff --git a/Documentation/devicetree/bindings/sound/mt8183-mt6358-ts3a227-max98357.txt b/Documentation/devicetree/bindings/sound/mt8183-mt6358-ts3a227-max98357.txt new file mode 100644 index 000000000000..d6d5207fa996 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/mt8183-mt6358-ts3a227-max98357.txt @@ -0,0 +1,15 @@ +MT8183 with MT6358, TS3A227 and MAX98357 CODECS + +Required properties: +- compatible : "mediatek,mt8183_mt6358_ts3a227_max98357" +- mediatek,headset-codec: the phandles of ts3a227 codecs +- mediatek,platform: the phandle of MT8183 ASoC platform + +Example: + + sound { + compatible = "mediatek,mt8183_mt6358_ts3a227_max98357"; + mediatek,headset-codec = <&ts3a227>; + mediatek,platform = <&afe>; + }; + diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 648d43e1b1e9..5c52182f7dcf 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -266,6 +266,7 @@ Required properties: - "renesas,rcar_sound-r8a7743" (RZ/G1M) - "renesas,rcar_sound-r8a7744" (RZ/G1N) - "renesas,rcar_sound-r8a7745" (RZ/G1E) + - "renesas,rcar_sound-r8a77470" (RZ/G1C) - "renesas,rcar_sound-r8a774a1" (RZ/G2M) - "renesas,rcar_sound-r8a774c0" (RZ/G2E) - "renesas,rcar_sound-r8a7778" (R-Car M1A) @@ -282,7 +283,12 @@ Required properties: - reg : Should contain the register physical address. required register is SRU/ADG/SSI if generation1 - SRU/ADG/SSIU/SSI if generation2 + SRU/ADG/SSIU/SSI/AUDIO-DMAC-periperi if generation2/generation3 + Select extended AUDIO-DMAC-periperi address if SoC has it, + otherwise select normal AUDIO-DMAC-periperi address. +- reg-names : Should contain the register names. + scu/adg/ssi if generation1 + scu/adg/ssiu/ssi/audmapp if generation2/generation3 - rcar_sound,ssi : Should contain SSI feature. The number of SSI subnode should be same as HW. see below for detail. diff --git a/Documentation/devicetree/bindings/sound/rockchip,pdm.txt b/Documentation/devicetree/bindings/sound/rockchip,pdm.txt index 47f164fbd1d7..98572a25122f 100644 --- a/Documentation/devicetree/bindings/sound/rockchip,pdm.txt +++ b/Documentation/devicetree/bindings/sound/rockchip,pdm.txt @@ -3,6 +3,9 @@ Required properties: - compatible: "rockchip,pdm" + - "rockchip,px30-pdm" + - "rockchip,rk1808-pdm" + - "rockchip,rk3308-pdm" - reg: physical base address of the controller and length of memory mapped region. - dmas: DMA specifiers for rx dma. See the DMA client binding, @@ -12,6 +15,8 @@ Required properties: - clock-names: should contain following: - "pdm_hclk": clock for PDM BUS - "pdm_clk" : clock for PDM controller +- resets: a list of phandle + reset-specifer paris, one for each entry in reset-names. +- reset-names: reset names, should include "pdm-m". - pinctrl-names: Must contain a "default" entry. - pinctrl-N: One property must exist for each entry in pinctrl-names. See ../pinctrl/pinctrl-bindings.txt diff --git a/Documentation/devicetree/bindings/sound/rt5651.txt b/Documentation/devicetree/bindings/sound/rt5651.txt index a41199a5cd79..56e736a1cba9 100644 --- a/Documentation/devicetree/bindings/sound/rt5651.txt +++ b/Documentation/devicetree/bindings/sound/rt5651.txt @@ -22,6 +22,11 @@ Optional properties: 2: Use JD1_2 pin for jack-detect 3: Use JD2 pin for jack-detect +- realtek,jack-detect-not-inverted + bool. Normal jack-detect switches give an inverted (active-low) signal, + set this bool in the rare case you've a jack-detect switch which is not + inverted. + - realtek,over-current-threshold-microamp u32, micbias over-current detection threshold in µA, valid values are 600, 1500 and 2000µA. diff --git a/Documentation/devicetree/bindings/sound/simple-amplifier.txt b/Documentation/devicetree/bindings/sound/simple-amplifier.txt index 7182ac4f1e65..b1b097cc9b68 100644 --- a/Documentation/devicetree/bindings/sound/simple-amplifier.txt +++ b/Documentation/devicetree/bindings/sound/simple-amplifier.txt @@ -2,9 +2,9 @@ Simple Amplifier Audio Driver Required properties: - compatible : "dioo,dio2125" or "simple-audio-amplifier" -- enable-gpios : the gpio connected to the enable pin of the simple amplifier Optional properties: +- enable-gpios : the gpio connected to the enable pin of the simple amplifier - VCC-supply : power supply for the device, as covered in Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt index 4629c8f8a6b6..79954cd6e37b 100644 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ b/Documentation/devicetree/bindings/sound/simple-card.txt @@ -24,6 +24,8 @@ Optional properties: a microphone is attached. - simple-audio-card,aux-devs : List of phandles pointing to auxiliary devices, such as amplifiers, to be added to the sound card. +- simple-audio-card,pin-switches : List of strings containing the widget names for + which pin switches must be created. Optional subnodes: diff --git a/Documentation/devicetree/bindings/sound/sprd-mcdt.txt b/Documentation/devicetree/bindings/sound/sprd-mcdt.txt new file mode 100644 index 000000000000..274ba0acbfd6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/sprd-mcdt.txt @@ -0,0 +1,19 @@ +Spreadtrum Multi-Channel Data Transfer Binding + +The Multi-channel data transfer controller is used for sound stream +transmission between audio subsystem and other AP/CP subsystem. It +supports 10 DAC channel and 10 ADC channel, and each channel can be +configured with DMA mode or interrupt mode. + +Required properties: +- compatible: Should be "sprd,sc9860-mcdt". +- reg: Should contain registers address and length. +- interrupts: Should contain one interrupt shared by all channel. + +Example: + +mcdt@41490000 { + compatible = "sprd,sc9860-mcdt"; + reg = <0 0x41490000 0 0x170>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 686771d056c7..9ed399977297 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -305,6 +305,7 @@ oranth Shenzhen Oranth Technology Co., Ltd. ORCL Oracle Corporation orisetech Orise Technology ortustech Ortus Technology Co., Ltd. +osddisplays OSD Displays ovti OmniVision Technologies oxsemi Oxford Semiconductor, Ltd. panasonic Panasonic Corporation @@ -347,7 +348,9 @@ ricoh Ricoh Co. Ltd. rikomagic Rikomagic Tech Corp. Ltd riscv RISC-V Foundation rockchip Fuzhou Rockchip Electronics Co., Ltd +rocktech ROCKTECH DISPLAYS LIMITED rohm ROHM Semiconductor Co., Ltd +ronbo Ronbo Electronics roofull Shenzhen Roofull Technology Co, Ltd samsung Samsung Semiconductor samtec Samtec/Softing company diff --git a/Documentation/driver-api/component.rst b/Documentation/driver-api/component.rst index 2da4a8f20607..57e37590733f 100644 --- a/Documentation/driver-api/component.rst +++ b/Documentation/driver-api/component.rst @@ -1,3 +1,5 @@ +.. _component: + ====================================== Component Helper for Aggregate Drivers ====================================== diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt index d7d6f01e81ff..99994a461359 100644 --- a/Documentation/driver-model/devres.txt +++ b/Documentation/driver-model/devres.txt @@ -256,6 +256,9 @@ DMA dmam_pool_create() dmam_pool_destroy() +DRM + devm_drm_dev_init() + GPIO devm_gpiod_get() devm_gpiod_get_index() diff --git a/Documentation/gpu/drm-internals.rst b/Documentation/gpu/drm-internals.rst index 3ae23a5454ac..966bd2d9f0cc 100644 --- a/Documentation/gpu/drm-internals.rst +++ b/Documentation/gpu/drm-internals.rst @@ -93,6 +93,11 @@ Device Instance and Driver Handling Driver Load ----------- +Component Helper Usage +~~~~~~~~~~~~~~~~~~~~~~ + +.. kernel-doc:: drivers/gpu/drm/drm_drv.c + :doc: component helper usage recommendations IRQ Helper Library ~~~~~~~~~~~~~~~~~~ diff --git a/Documentation/gpu/drm-kms-helpers.rst b/Documentation/gpu/drm-kms-helpers.rst index 17ca7f8bf3d3..14102ae035dc 100644 --- a/Documentation/gpu/drm-kms-helpers.rst +++ b/Documentation/gpu/drm-kms-helpers.rst @@ -107,6 +107,12 @@ fbdev Helper Functions Reference .. kernel-doc:: drivers/gpu/drm/drm_fb_helper.c :export: +format Helper Functions Reference +================================= + +.. kernel-doc:: drivers/gpu/drm/drm_format_helper.c + :export: + Framebuffer CMA Helper Functions Reference ========================================== @@ -369,3 +375,15 @@ Legacy CRTC/Modeset Helper Functions Reference .. kernel-doc:: drivers/gpu/drm/drm_crtc_helper.c :export: + +SHMEM GEM Helper Reference +========================== + +.. kernel-doc:: drivers/gpu/drm/drm_gem_shmem_helper.c + :doc: overview + +.. kernel-doc:: include/drm/drm_gem_shmem_helper.h + :internal: + +.. kernel-doc:: drivers/gpu/drm/drm_gem_shmem_helper.c + :export: diff --git a/Documentation/gpu/kms-properties.csv b/Documentation/gpu/kms-properties.csv index bfde04eddd14..07ed22ea3bd6 100644 --- a/Documentation/gpu/kms-properties.csv +++ b/Documentation/gpu/kms-properties.csv @@ -17,7 +17,6 @@ Owner Module/Drivers,Group,Property Name,Type,Property Values,Object attached,De ,Virtual GPU,“suggested X”,RANGE,"Min=0, Max=0xffffffff",Connector,property to suggest an X offset for a connector ,,“suggested Y”,RANGE,"Min=0, Max=0xffffffff",Connector,property to suggest an Y offset for a connector ,Optional,"""aspect ratio""",ENUM,"{ ""None"", ""4:3"", ""16:9"" }",Connector,TDB -,Optional,"""content type""",ENUM,"{ ""No Data"", ""Graphics"", ""Photo"", ""Cinema"", ""Game"" }",Connector,TBD i915,Generic,"""Broadcast RGB""",ENUM,"{ ""Automatic"", ""Full"", ""Limited 16:235"" }",Connector,"When this property is set to Limited 16:235 and CTM is set, the hardware will be programmed with the result of the multiplication of CTM by the limited range matrix to ensure the pixels normaly in the range 0..1.0 are remapped to the range 16/255..235/255." ,,“audio”,ENUM,"{ ""force-dvi"", ""off"", ""auto"", ""on"" }",Connector,TBD ,SDVO-TV,“mode”,ENUM,"{ ""NTSC_M"", ""NTSC_J"", ""NTSC_443"", ""PAL_B"" } etc.",Connector,TBD diff --git a/Documentation/gpu/meson.rst b/Documentation/gpu/meson.rst index 479f6f51a13b..b9e2f9aa3bd8 100644 --- a/Documentation/gpu/meson.rst +++ b/Documentation/gpu/meson.rst @@ -42,12 +42,6 @@ Video Encoder .. kernel-doc:: drivers/gpu/drm/meson/meson_venc.c :doc: Video Encoder -Video Canvas Management -======================= - -.. kernel-doc:: drivers/gpu/drm/meson/meson_canvas.c - :doc: Canvas - Video Clocks ============ diff --git a/Documentation/gpu/tinydrm.rst b/Documentation/gpu/tinydrm.rst index a913644bfc19..33a41544f659 100644 --- a/Documentation/gpu/tinydrm.rst +++ b/Documentation/gpu/tinydrm.rst @@ -1,34 +1,22 @@ -========================== -drm/tinydrm Driver library -========================== +============================ +drm/tinydrm Tiny DRM drivers +============================ -.. kernel-doc:: drivers/gpu/drm/tinydrm/core/tinydrm-core.c - :doc: overview - -Core functionality -================== +tinydrm is a collection of DRM drivers that are so small they can fit in a +single source file. -.. kernel-doc:: drivers/gpu/drm/tinydrm/core/tinydrm-core.c - :doc: core +Helpers +======= -.. kernel-doc:: include/drm/tinydrm/tinydrm.h +.. kernel-doc:: include/drm/tinydrm/tinydrm-helpers.h :internal: -.. kernel-doc:: drivers/gpu/drm/tinydrm/core/tinydrm-core.c +.. kernel-doc:: drivers/gpu/drm/tinydrm/core/tinydrm-helpers.c :export: .. kernel-doc:: drivers/gpu/drm/tinydrm/core/tinydrm-pipe.c :export: -Additional helpers -================== - -.. kernel-doc:: include/drm/tinydrm/tinydrm-helpers.h - :internal: - -.. kernel-doc:: drivers/gpu/drm/tinydrm/core/tinydrm-helpers.c - :export: - MIPI DBI Compatible Controllers =============================== diff --git a/Documentation/gpu/todo.rst b/Documentation/gpu/todo.rst index 159a4aba49e6..1528ad2d598b 100644 --- a/Documentation/gpu/todo.rst +++ b/Documentation/gpu/todo.rst @@ -215,12 +215,12 @@ Might be good to also have some igt testcases for this. Contact: Daniel Vetter, Noralf Tronnes -Put a reservation_object into drm_gem_object +Remove the ->gem_prime_res_obj callback -------------------------------------------- -This would remove the need for the ->gem_prime_res_obj callback. It would also -allow us to implement generic helpers for waiting for a bo, allowing for quite a -bit of refactoring in the various wait ioctl implementations. +The ->gem_prime_res_obj callback can be removed from drivers by using the +reservation_object in the drm_gem_object. It may also be possible to use the +generic drm_gem_reservation_object_wait helper for waiting for a bo. Contact: Daniel Vetter @@ -469,10 +469,6 @@ those drivers as simple as possible, so lots of room for refactoring: one of the ideas for having a shared dsi/dbi helper, abstracting away the transport details more. -- Quick aside: The unregister devm stuff is kinda getting the lifetimes of - a drm_device wrong. Doesn't matter, since everyone else gets it wrong - too :-) - Contact: Noralf Trønnes, Daniel Vetter AMD DC Display Driver diff --git a/Documentation/i2c/busses/i2c-amd-mp2 b/Documentation/i2c/busses/i2c-amd-mp2 new file mode 100644 index 000000000000..6571487171f4 --- /dev/null +++ b/Documentation/i2c/busses/i2c-amd-mp2 @@ -0,0 +1,23 @@ +Kernel driver i2c-amd-mp2 + +Supported adapters: + * AMD MP2 PCIe interface + +Datasheet: not publicly available. + +Authors: + Shyam Sundar S K <Shyam-sundar.S-k@amd.com> + Nehal Shah <nehal-bakulchandra.shah@amd.com> + Elie Morisse <syniurge@gmail.com> + +Description +----------- + +The MP2 is an ARM processor programmed as an I2C controller and communicating +with the x86 host through PCI. + +If you see something like this: + +03:00.7 MP2 I2C controller: Advanced Micro Devices, Inc. [AMD] Device 15e6 + +in your 'lspci -v', then this driver is for your device. diff --git a/Documentation/i2c/busses/i2c-piix4 b/Documentation/i2c/busses/i2c-piix4 index aa959fd22450..2703bc3acad0 100644 --- a/Documentation/i2c/busses/i2c-piix4 +++ b/Documentation/i2c/busses/i2c-piix4 @@ -15,6 +15,8 @@ Supported adapters: http://support.amd.com/us/Embedded_TechDocs/44413.pdf * AMD Hudson-2, ML, CZ Datasheet: Not publicly available + * Hygon CZ + Datasheet: Not publicly available * Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge Datasheet: Publicly available at the SMSC website http://www.smsc.com diff --git a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst index 6b154dbb02cc..132f5eb9b530 100644 --- a/Documentation/sound/kernel-api/writing-an-alsa-driver.rst +++ b/Documentation/sound/kernel-api/writing-an-alsa-driver.rst @@ -324,7 +324,7 @@ to details explained in the following section. strcpy(card->driver, "My Chip"); strcpy(card->shortname, "My Own Chip 123"); sprintf(card->longname, "%s at 0x%lx irq %i", - card->shortname, chip->ioport, chip->irq); + card->shortname, chip->port, chip->irq); /* (5) */ .... /* implemented later */ @@ -437,7 +437,7 @@ Since each component can be properly freed, the single strcpy(card->driver, "My Chip"); strcpy(card->shortname, "My Own Chip 123"); sprintf(card->longname, "%s at 0x%lx irq %i", - card->shortname, chip->ioport, chip->irq); + card->shortname, chip->port, chip->irq); The driver field holds the minimal ID string of the chip. This is used by alsa-lib's configurator, so keep it simple but unique. Even the |