diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/power/supply/bq24190.txt | 51 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/power/supply/ltc2941.txt | 15 |
2 files changed, 59 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/power/supply/bq24190.txt b/Documentation/devicetree/bindings/power/supply/bq24190.txt new file mode 100644 index 000000000000..9e517d307070 --- /dev/null +++ b/Documentation/devicetree/bindings/power/supply/bq24190.txt @@ -0,0 +1,51 @@ +TI BQ24190 Li-Ion Battery Charger + +Required properties: +- compatible: contains one of the following: + * "ti,bq24190" + * "ti,bq24192i" +- reg: integer, I2C address of the charger. +- interrupts[-extended]: configuration for charger INT pin. + +Optional properties: +- monitored-battery: phandle of battery characteristics devicetree node + The charger uses the following battery properties: + + precharge-current-microamp: maximum charge current during precharge + phase (typically 20% of battery capacity). + + charge-term-current-microamp: a charge cycle terminates when the + battery voltage is above recharge threshold, and the current is below + this setting (typically 10% of battery capacity). + See also Documentation/devicetree/bindings/power/supply/battery.txt +- ti,system-minimum-microvolt: when power is connected and the battery is below + minimum system voltage, the system will be regulated above this setting. + +Notes: +- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default + charge current on USB SDP ports, among other features). To simulate this on + boards that wire the pin to a GPIO, set a gpio-hog. + +Example: + + bat: battery { + compatible = "simple-battery"; + precharge-current-microamp = <256000>; + charge-term-current-microamp = <128000>; + // etc. + }; + + bq24190: charger@6a { + compatible = "ti,bq24190"; + reg = <0x6a>; + interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>; + monitored-battery = <&bat>; + ti,system-minimum-microvolt = <3200000>; + }; + + &twl_gpio { + otg { + gpio-hog; + gpios = <6 0>; + output-high; + line-name = "otg-gpio"; + }; + }; diff --git a/Documentation/devicetree/bindings/power/supply/ltc2941.txt b/Documentation/devicetree/bindings/power/supply/ltc2941.txt index a9d7aa60558b..3b9ba147b041 100644 --- a/Documentation/devicetree/bindings/power/supply/ltc2941.txt +++ b/Documentation/devicetree/bindings/power/supply/ltc2941.txt @@ -1,13 +1,14 @@ -binding for LTC2941 and LTC2943 battery gauges +binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery gauges -Both the LTC2941 and LTC2943 measure battery capacity. -The LTC2943 is compatible with the LTC2941, it adds voltage and -temperature monitoring, and uses a slightly different conversion -formula for the charge counter. +All chips measure battery capacity. +The LTC2942 is pin compatible with the LTC2941, it adds voltage and +temperature monitoring, and is runtime detected. LTC2943 and LTC2944 +is software compatible, uses a slightly different conversion formula +for the charge counter and adds voltage, current and temperature monitoring. Required properties: -- compatible: Should contain "lltc,ltc2941" or "lltc,ltc2943" which also - indicates the type of I2C chip attached. +- compatible: Should contain "lltc,ltc2941", "lltc,ltc2942", "lltc,ltc2943" + or "lltc,ltc2944" which also indicates the type of I2C chip attached. - reg: The 7-bit I2C address. - lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit negative value when the battery has been connected to the wrong end of the |