diff options
Diffstat (limited to 'Documentation')
126 files changed, 3332 insertions, 1801 deletions
diff --git a/Documentation/ABI/testing/configfs-iio b/Documentation/ABI/testing/configfs-iio new file mode 100644 index 000000000000..2483756fccf5 --- /dev/null +++ b/Documentation/ABI/testing/configfs-iio @@ -0,0 +1,21 @@ +What: /config/iio +Date: October 2015 +KernelVersion: 4.4 +Contact: linux-iio@vger.kernel.org +Description: + This represents Industrial IO configuration entry point + directory. It contains sub-groups corresponding to IIO + objects. + +What: /config/iio/triggers +Date: October 2015 +KernelVersion: 4.4 +Description: + Industrial IO software triggers directory. + +What: /config/iio/triggers/hrtimers +Date: October 2015 +KernelVersion: 4.4 +Description: + High resolution timers directory. Creating a directory here + will result in creating a hrtimer trigger in the IIO subsystem. diff --git a/Documentation/ABI/testing/configfs-usb-gadget-sourcesink b/Documentation/ABI/testing/configfs-usb-gadget-sourcesink index bc7ff731aa0c..f56335af2d88 100644 --- a/Documentation/ABI/testing/configfs-usb-gadget-sourcesink +++ b/Documentation/ABI/testing/configfs-usb-gadget-sourcesink @@ -10,3 +10,5 @@ Description: isoc_mult - 0..2 (hs/ss only) isoc_maxburst - 0..15 (ss only) buflen - buffer length + bulk_qlen - depth of queue for bulk + iso_qlen - depth of queue for iso diff --git a/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc b/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc new file mode 100644 index 000000000000..8916f7ec6507 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc @@ -0,0 +1,24 @@ +What: /sys/bus/iio/devices/iio:deviceX/in_allow_async_readout +Date: December 2015 +KernelVersion: 4.4 +Contact: linux-iio@vger.kernel.org +Description: + By default (value '0'), the capture thread checks for the Conversion + Ready Flag to being set prior to committing a new value to the sample + buffer. This synchronizes the in-chip conversion rate with the + in-driver readout rate at the cost of an additional register read. + + Writing '1' will remove the polling for the Conversion Ready Flags to + save the additional i2c transaction, which will improve the bandwidth + available for reading data. However, samples can be occasionally skipped + or repeated, depending on the beat between the capture and conversion + rates. + +What: /sys/bus/iio/devices/iio:deviceX/in_shunt_resistor +Date: December 2015 +KernelVersion: 4.4 +Contact: linux-iio@vger.kernel.org +Description: + The value of the shunt resistor may be known only at runtime fom an + eeprom content read by a client application. This attribute allows to + set its value in ohms. diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb index 3a4abfc44f5e..0bd731cbb50c 100644 --- a/Documentation/ABI/testing/sysfs-bus-usb +++ b/Documentation/ABI/testing/sysfs-bus-usb @@ -134,19 +134,21 @@ Description: enabled for the device. Developer can write y/Y/1 or n/N/0 to the file to enable/disable the feature. -What: /sys/bus/usb/devices/.../power/usb3_hardware_lpm -Date: June 2015 +What: /sys/bus/usb/devices/.../power/usb3_hardware_lpm_u1 + /sys/bus/usb/devices/.../power/usb3_hardware_lpm_u2 +Date: November 2015 Contact: Kevin Strasser <kevin.strasser@linux.intel.com> + Lu Baolu <baolu.lu@linux.intel.com> Description: If CONFIG_PM is set and a USB 3.0 lpm-capable device is plugged in to a xHCI host which supports link PM, it will check if U1 and U2 exit latencies have been set in the BOS descriptor; if - the check is is passed and the host supports USB3 hardware LPM, + the check is passed and the host supports USB3 hardware LPM, USB3 hardware LPM will be enabled for the device and the USB - device directory will contain a file named - power/usb3_hardware_lpm. The file holds a string value (enable - or disable) indicating whether or not USB3 hardware LPM is - enabled for the device. + device directory will contain two files named + power/usb3_hardware_lpm_u1 and power/usb3_hardware_lpm_u2. These + files hold a string value (enable or disable) indicating whether + or not USB3 hardware LPM U1 or U2 is enabled for the device. What: /sys/bus/usb/devices/.../removable Date: February 2012 @@ -187,6 +189,17 @@ Description: The file will read "hotplug", "wired" and "not used" if the information is available, and "unknown" otherwise. +What: /sys/bus/usb/devices/.../(hub interface)/portX/usb3_lpm_permit +Date: November 2015 +Contact: Lu Baolu <baolu.lu@linux.intel.com> +Description: + Some USB3.0 devices are not friendly to USB3 LPM. usb3_lpm_permit + attribute allows enabling/disabling usb3 lpm of a port. It takes + effect both before and after a usb device is enumerated. Supported + values are "0" if both u1 and u2 are NOT permitted, "u1" if only u1 + is permitted, "u2" if only u2 is permitted, "u1_u2" if both u1 and + u2 are permitted. + What: /sys/bus/usb/devices/.../power/usb2_lpm_l1_timeout Date: May 2013 Contact: Mathias Nyman <mathias.nyman@linux.intel.com> diff --git a/Documentation/ABI/testing/sysfs-fs-f2fs b/Documentation/ABI/testing/sysfs-fs-f2fs index 0345f2d1c727..e5200f354abf 100644 --- a/Documentation/ABI/testing/sysfs-fs-f2fs +++ b/Documentation/ABI/testing/sysfs-fs-f2fs @@ -87,6 +87,12 @@ Contact: "Jaegeuk Kim" <jaegeuk@kernel.org> Description: Controls the checkpoint timing. +What: /sys/fs/f2fs/<disk>/idle_interval +Date: January 2016 +Contact: "Jaegeuk Kim" <jaegeuk@kernel.org> +Description: + Controls the idle timing. + What: /sys/fs/f2fs/<disk>/ra_nid_pages Date: October 2015 Contact: "Chao Yu" <chao2.yu@samsung.com> diff --git a/Documentation/ABI/testing/sysfs-kernel-livepatch b/Documentation/ABI/testing/sysfs-kernel-livepatch index 5bf42a840b22..da87f43aec58 100644 --- a/Documentation/ABI/testing/sysfs-kernel-livepatch +++ b/Documentation/ABI/testing/sysfs-kernel-livepatch @@ -33,7 +33,7 @@ Description: The object directory contains subdirectories for each function that is patched within the object. -What: /sys/kernel/livepatch/<patch>/<object>/<function> +What: /sys/kernel/livepatch/<patch>/<object>/<function,sympos> Date: Nov 2014 KernelVersion: 3.19.0 Contact: live-patching@vger.kernel.org @@ -41,4 +41,8 @@ Description: The function directory contains attributes regarding the properties and state of the patched function. + The directory name contains the patched function name and a + sympos number corresponding to the nth occurrence of the symbol + name in kallsyms for the patched object. + There are currently no such attributes. diff --git a/Documentation/ABI/testing/sysfs-ptp b/Documentation/ABI/testing/sysfs-ptp index 44806a678f12..a17f817a9309 100644 --- a/Documentation/ABI/testing/sysfs-ptp +++ b/Documentation/ABI/testing/sysfs-ptp @@ -74,7 +74,7 @@ Description: assignment may be changed by two writing numbers into the file. -What: /sys/class/ptp/ptpN/pps_avaiable +What: /sys/class/ptp/ptpN/pps_available Date: September 2010 Contact: Richard Cochran <richardcochran@gmail.com> Description: diff --git a/Documentation/DocBook/device-drivers.tmpl b/Documentation/DocBook/device-drivers.tmpl index 7b3fcc5effcd..cdd8b24db68d 100644 --- a/Documentation/DocBook/device-drivers.tmpl +++ b/Documentation/DocBook/device-drivers.tmpl @@ -263,6 +263,7 @@ X!Isound/sound_firmware.c !Iinclude/media/lirc_dev.h </sect1> <sect1><title>Media Controller devices</title> +!Pinclude/media/media-device.h Media Controller !Iinclude/media/media-device.h !Iinclude/media/media-devnode.h !Iinclude/media/media-entity.h diff --git a/Documentation/DocBook/media/v4l/media-controller.xml b/Documentation/DocBook/media/v4l/media-controller.xml index 873ac3a621f0..5f2fc07a93d7 100644 --- a/Documentation/DocBook/media/v4l/media-controller.xml +++ b/Documentation/DocBook/media/v4l/media-controller.xml @@ -58,21 +58,36 @@ <title>Media device model</title> <para>Discovering a device internal topology, and configuring it at runtime, is one of the goals of the media controller API. To achieve this, hardware - devices are modelled as an oriented graph of building blocks called entities - connected through pads.</para> - <para>An entity is a basic media hardware or software building block. It can - correspond to a large variety of logical blocks such as physical hardware - devices (CMOS sensor for instance), logical hardware devices (a building - block in a System-on-Chip image processing pipeline), DMA channels or - physical connectors.</para> - <para>A pad is a connection endpoint through which an entity can interact - with other entities. Data (not restricted to video) produced by an entity - flows from the entity's output to one or more entity inputs. Pads should not - be confused with physical pins at chip boundaries.</para> - <para>A link is a point-to-point oriented connection between two pads, - either on the same entity or on different entities. Data flows from a source - pad to a sink pad.</para> + devices and Linux Kernel interfaces are modelled as graph objects on + an oriented graph. The object types that constitute the graph are:</para> + <itemizedlist> + <listitem><para>An <emphasis role="bold">entity</emphasis> + is a basic media hardware or software building block. It can correspond to + a large variety of logical blocks such as physical hardware devices + (CMOS sensor for instance), logical hardware devices (a building block in + a System-on-Chip image processing pipeline), DMA channels or physical + connectors.</para></listitem> + <listitem><para>An <emphasis role="bold">interface</emphasis> + is a graph representation of a Linux Kernel userspace API interface, + like a device node or a sysfs file that controls one or more entities + in the graph.</para></listitem> + <listitem><para>A <emphasis role="bold">pad</emphasis> + is a data connection endpoint through which an entity can interact with + other entities. Data (not restricted to video) produced by an entity + flows from the entity's output to one or more entity inputs. Pads should + not be confused with physical pins at chip boundaries.</para></listitem> + <listitem><para>A <emphasis role="bold">data link</emphasis> + is a point-to-point oriented connection between two pads, either on the + same entity or on different entities. Data flows from a source pad to a + sink pad.</para></listitem> + <listitem><para>An <emphasis role="bold">interface link</emphasis> + is a point-to-point bidirectional control connection between a Linux + Kernel interface and an entity.m</para></listitem> + </itemizedlist> </section> + + <!-- All non-ioctl specific data types go here. --> + &sub-media-types; </chapter> <appendix id="media-user-func"> @@ -83,6 +98,7 @@ &sub-media-func-ioctl; <!-- All ioctls go here. --> &sub-media-ioc-device-info; + &sub-media-ioc-g-topology; &sub-media-ioc-enum-entities; &sub-media-ioc-enum-links; &sub-media-ioc-setup-link; diff --git a/Documentation/DocBook/media/v4l/media-ioc-enum-entities.xml b/Documentation/DocBook/media/v4l/media-ioc-enum-entities.xml index 5872f8bbf774..0c4f96bfc2de 100644 --- a/Documentation/DocBook/media/v4l/media-ioc-enum-entities.xml +++ b/Documentation/DocBook/media/v4l/media-ioc-enum-entities.xml @@ -59,15 +59,6 @@ <para>Entity IDs can be non-contiguous. Applications must <emphasis>not</emphasis> try to enumerate entities by calling MEDIA_IOC_ENUM_ENTITIES with increasing id's until they get an error.</para> - <para>Two or more entities that share a common non-zero - <structfield>group_id</structfield> value are considered as logically - grouped. Groups are used to report - <itemizedlist> - <listitem><para>ALSA, VBI and video nodes that carry the same media - stream</para></listitem> - <listitem><para>lens and flash controllers associated with a sensor</para></listitem> - </itemizedlist> - </para> <table pgwide="1" frame="none" id="media-entity-desc"> <title>struct <structname>media_entity_desc</structname></title> @@ -106,7 +97,7 @@ <entry><structfield>revision</structfield></entry> <entry></entry> <entry></entry> - <entry>Entity revision in a driver/hardware specific format.</entry> + <entry>Entity revision. Always zero (obsolete)</entry> </row> <row> <entry>__u32</entry> @@ -120,7 +111,7 @@ <entry><structfield>group_id</structfield></entry> <entry></entry> <entry></entry> - <entry>Entity group ID</entry> + <entry>Entity group ID. Always zero (obsolete)</entry> </row> <row> <entry>__u16</entry> @@ -171,97 +162,6 @@ </tbody> </tgroup> </table> - - <table frame="none" pgwide="1" id="media-entity-type"> - <title>Media entity types</title> - <tgroup cols="2"> - <colspec colname="c1"/> - <colspec colname="c2"/> - <tbody valign="top"> - <row> - <entry><constant>MEDIA_ENT_T_DEVNODE</constant></entry> - <entry>Unknown device node</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_DEVNODE_V4L</constant></entry> - <entry>V4L video, radio or vbi device node</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_DEVNODE_FB</constant></entry> - <entry>Frame buffer device node</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_DEVNODE_ALSA</constant></entry> - <entry>ALSA card</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_DEVNODE_DVB_FE</constant></entry> - <entry>DVB frontend devnode</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_DEVNODE_DVB_DEMUX</constant></entry> - <entry>DVB demux devnode</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_DEVNODE_DVB_DVR</constant></entry> - <entry>DVB DVR devnode</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_DEVNODE_DVB_CA</constant></entry> - <entry>DVB CAM devnode</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_DEVNODE_DVB_NET</constant></entry> - <entry>DVB network devnode</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_V4L2_SUBDEV</constant></entry> - <entry>Unknown V4L sub-device</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_V4L2_SUBDEV_SENSOR</constant></entry> - <entry>Video sensor</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_V4L2_SUBDEV_FLASH</constant></entry> - <entry>Flash controller</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_V4L2_SUBDEV_LENS</constant></entry> - <entry>Lens controller</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_V4L2_SUBDEV_DECODER</constant></entry> - <entry>Video decoder, the basic function of the video decoder is to - accept analogue video from a wide variety of sources such as - broadcast, DVD players, cameras and video cassette recorders, in - either NTSC, PAL or HD format and still occasionally SECAM, separate - it into its component parts, luminance and chrominance, and output - it in some digital video standard, with appropriate embedded timing - signals.</entry> - </row> - <row> - <entry><constant>MEDIA_ENT_T_V4L2_SUBDEV_TUNER</constant></entry> - <entry>TV and/or radio tuner</entry> - </row> - </tbody> - </tgroup> - </table> - - <table frame="none" pgwide="1" id="media-entity-flag"> - <title>Media entity flags</title> - <tgroup cols="2"> - <colspec colname="c1"/> - <colspec colname="c2"/> - <tbody valign="top"> - <row> - <entry><constant>MEDIA_ENT_FL_DEFAULT</constant></entry> - <entry>Default entity for its type. Used to discover the default - audio, VBI and video devices, the default camera sensor, ...</entry> - </row> - </tbody> - </tgroup> - </table> </refsect1> <refsect1> diff --git a/Documentation/DocBook/media/v4l/media-ioc-enum-links.xml b/Documentation/DocBook/media/v4l/media-ioc-enum-links.xml index 74fb394ec667..2bbeea9f3e18 100644 --- a/Documentation/DocBook/media/v4l/media-ioc-enum-links.xml +++ b/Documentation/DocBook/media/v4l/media-ioc-enum-links.xml @@ -118,35 +118,6 @@ </tgroup> </table> - <table frame="none" pgwide="1" id="media-pad-flag"> - <title>Media pad flags</title> - <tgroup cols="2"> - <colspec colname="c1"/> - <colspec colname="c2"/> - <tbody valign="top"> - <row> - <entry><constant>MEDIA_PAD_FL_SINK</constant></entry> - <entry>Input pad, relative to the entity. Input pads sink data and - are targets of links.</entry> - </row> - <row> - <entry><constant>MEDIA_PAD_FL_SOURCE</constant></entry> - <entry>Output pad, relative to the entity. Output pads source data - and are origins of links.</entry> - </row> - <row> - <entry><constant>MEDIA_PAD_FL_MUST_CONNECT</constant></entry> - <entry>If this flag is set and the pad is linked to any other - pad, then at least one of those links must be enabled for the - entity to be able to stream. There could be temporary reasons - (e.g. device configuration dependent) for the pad to need - enabled links even when this flag isn't set; the absence of the - flag doesn't imply there is none.</entry> - </row> - </tbody> - </tgroup> - </table> - <table pgwide="1" frame="none" id="media-link-desc"> <title>struct <structname>media_link_desc</structname></title> <tgroup cols="3"> @@ -171,33 +142,6 @@ </tgroup> </table> - <table frame="none" pgwide="1" id="media-link-flag"> - <title>Media link flags</title> - <tgroup cols="2"> - <colspec colname="c1"/> - <colspec colname="c2"/> - <tbody valign="top"> - <row> - <entry><constant>MEDIA_LNK_FL_ENABLED</constant></entry> - <entry>The link is enabled and can be used to transfer media data. - When two or more links target a sink pad, only one of them can be - enabled at a time.</entry> - </row> - <row> - <entry><constant>MEDIA_LNK_FL_IMMUTABLE</constant></entry> - <entry>The link enabled state can't be modified at runtime. An - immutable link is always enabled.</entry> - </row> - <row> - <entry><constant>MEDIA_LNK_FL_DYNAMIC</constant></entry> - <entry>The link enabled state can be modified during streaming. This - flag is set by drivers and is read-only for applications.</entry> - </row> - </tbody> - </tgroup> - </table> - <para>One and only one of <constant>MEDIA_PAD_FL_SINK</constant> and - <constant>MEDIA_PAD_FL_SOURCE</constant> must be set for every pad.</para> </refsect1> <refsect1> diff --git a/Documentation/DocBook/media/v4l/media-ioc-g-topology.xml b/Documentation/DocBook/media/v4l/media-ioc-g-topology.xml new file mode 100644 index 000000000000..63152ab9efba --- /dev/null +++ b/Documentation/DocBook/media/v4l/media-ioc-g-topology.xml @@ -0,0 +1,394 @@ +<refentry id="media-g-topology"> + <refmeta> + <refentrytitle>ioctl MEDIA_IOC_G_TOPOLOGY</refentrytitle> + &manvol; + </refmeta> + + <refnamediv> + <refname>MEDIA_IOC_G_TOPOLOGY</refname> + <refpurpose>Enumerate the graph topology and graph element properties</refpurpose> + </refnamediv> + + <refsynopsisdiv> + <funcsynopsis> + <funcprototype> + <funcdef>int <function>ioctl</function></funcdef> + <paramdef>int <parameter>fd</parameter></paramdef> + <paramdef>int <parameter>request</parameter></paramdef> + <paramdef>struct media_v2_topology *<parameter>argp</parameter></paramdef> + </funcprototype> + </funcsynopsis> + </refsynopsisdiv> + + <refsect1> + <title>Arguments</title> + + <variablelist> + <varlistentry> + <term><parameter>fd</parameter></term> + <listitem> + <para>File descriptor returned by + <link linkend='media-func-open'><function>open()</function></link>.</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>request</parameter></term> + <listitem> + <para>MEDIA_IOC_G_TOPOLOGY</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>argp</parameter></term> + <listitem> + <para></para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> + + <refsect1> + <title>Description</title> + + <para><emphasis role="bold">NOTE:</emphasis> This new ioctl is programmed to be added on Kernel 4.6. Its definition/arguments may change until its final version.</para> + + <para>The typical usage of this ioctl is to call it twice. + On the first call, the structure defined at &media-v2-topology; should + be zeroed. At return, if no errors happen, this ioctl will return the + <constant>topology_version</constant> and the total number of entities, + interfaces, pads and links.</para> + <para>Before the second call, the userspace should allocate arrays to + store the graph elements that are desired, putting the pointers to them + at the ptr_entities, ptr_interfaces, ptr_links and/or ptr_pads, keeping + the other values untouched.</para> + <para>If the <constant>topology_version</constant> remains the same, the + ioctl should fill the desired arrays with the media graph elements.</para> + + <table pgwide="1" frame="none" id="media-v2-topology"> + <title>struct <structname>media_v2_topology</structname></title> + <tgroup cols="5"> + <colspec colname="c1" /> + <colspec colname="c2" /> + <colspec colname="c3" /> + <colspec colname="c4" /> + <colspec colname="c5" /> + <tbody valign="top"> + <row> + <entry>__u64</entry> + <entry><structfield>topology_version</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Version of the media graph topology. When the graph is + created, this field starts with zero. Every time a graph + element is added or removed, this field is + incremented.</entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>num_entities</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Number of entities in the graph</entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>ptr_entities</structfield></entry> + <entry></entry> + <entry></entry> + <entry>A pointer to a memory area where the entities array + will be stored, converted to a 64-bits integer. + It can be zero. if zero, the ioctl won't store the + entities. It will just update + <constant>num_entities</constant></entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>num_interfaces</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Number of interfaces in the graph</entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>ptr_interfaces</structfield></entry> + <entry></entry> + <entry></entry> + <entry>A pointer to a memory area where the interfaces array + will be stored, converted to a 64-bits integer. + It can be zero. if zero, the ioctl won't store the + interfaces. It will just update + <constant>num_interfaces</constant></entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>num_pads</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Total number of pads in the graph</entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>ptr_pads</structfield></entry> + <entry></entry> + <entry></entry> + <entry>A pointer to a memory area where the pads array + will be stored, converted to a 64-bits integer. + It can be zero. if zero, the ioctl won't store the + pads. It will just update + <constant>num_pads</constant></entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>num_links</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Total number of data and interface links in the graph</entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>ptr_links</structfield></entry> + <entry></entry> + <entry></entry> + <entry>A pointer to a memory area where the links array + will be stored, converted to a 64-bits integer. + It can be zero. if zero, the ioctl won't store the + links. It will just update + <constant>num_links</constant></entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="media-v2-entity"> + <title>struct <structname>media_v2_entity</structname></title> + <tgroup cols="5"> + <colspec colname="c1" /> + <colspec colname="c2" /> + <colspec colname="c3" /> + <colspec colname="c4" /> + <colspec colname="c5" /> + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>id</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Unique ID for the entity.</entry> + </row> + <row> + <entry>char</entry> + <entry><structfield>name</structfield>[64]</entry> + <entry></entry> + <entry></entry> + <entry>Entity name as an UTF-8 NULL-terminated string.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>function</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Entity main function, see <xref linkend="media-entity-type" /> for details.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[12]</entry> + <entry>Reserved for future extensions. Drivers and applications must + set this array to zero.</entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="media-v2-interface"> + <title>struct <structname>media_v2_interface</structname></title> + <tgroup cols="5"> + <colspec colname="c1" /> + <colspec colname="c2" /> + <colspec colname="c3" /> + <colspec colname="c4" /> + <colspec colname="c5" /> + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>id</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Unique ID for the interface.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>intf_type</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Interface type, see <xref linkend="media-intf-type" /> for details.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>flags</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Interface flags. Currently unused.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[9]</entry> + <entry></entry> + <entry></entry> + <entry>Reserved for future extensions. Drivers and applications must + set this array to zero.</entry> + </row> + <row> + <entry>struct media_v2_intf_devnode</entry> + <entry><structfield>devnode</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Used only for device node interfaces. See <xref linkend="media-v2-intf-devnode" /> for details..</entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="media-v2-intf-devnode"> + <title>struct <structname>media_v2_interface</structname></title> + <tgroup cols="5"> + <colspec colname="c1" /> + <colspec colname="c2" /> + <colspec colname="c3" /> + <colspec colname="c4" /> + <colspec colname="c5" /> + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>major</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Device node major number.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>minor</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Device node minor number.</entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="media-v2-pad"> + <title>struct <structname>media_v2_pad</structname></title> + <tgroup cols="5"> + <colspec colname="c1" /> + <colspec colname="c2" /> + <colspec colname="c3" /> + <colspec colname="c4" /> + <colspec colname="c5" /> + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>id</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Unique ID for the pad.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>entity_id</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Unique ID for the entity where this pad belongs.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>flags</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Pad flags, see <xref linkend="media-pad-flag" /> for more details.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[9]</entry> + <entry></entry> + <entry></entry> + <entry>Reserved for future extensions. Drivers and applications must + set this array to zero.</entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="media-v2-link"> + <title>struct <structname>media_v2_pad</structname></title> + <tgroup cols="5"> + <colspec colname="c1" /> + <colspec colname="c2" /> + <colspec colname="c3" /> + <colspec colname="c4" /> + <colspec colname="c5" /> + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>id</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Unique ID for the pad.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>source_id</structfield></entry> + <entry></entry> + <entry></entry> + <entry> + <para>On pad to pad links: unique ID for the source pad.</para> + <para>On interface to entity links: unique ID for the interface.</para> + </entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>sink_id</structfield></entry> + <entry></entry> + <entry></entry> + <entry> + <para>On pad to pad links: unique ID for the sink pad.</para> + <para>On interface to entity links: unique ID for the entity.</para> + </entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>flags</structfield></entry> + <entry></entry> + <entry></entry> + <entry>Link flags, see <xref linkend="media-link-flag" /> for more details.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[5]</entry> + <entry></entry> + <entry></entry> + <entry>Reserved for future extensions. Drivers and applications must + set this array to zero.</entry> + </row> + </tbody> + </tgroup> + </table> + + </refsect1> + + <refsect1> + &return-value; + + <variablelist> + <varlistentry> + <term><errorcode>ENOSPC</errorcode></term> + <listitem> + <para>This is returned when either one or more of the num_entities, + num_interfaces, num_links or num_pads are non-zero and are smaller + than the actual number of elements inside the graph. This may happen + if the <constant>topology_version</constant> changed when compared + to the last time this ioctl was called. Userspace should usually + free the area for the pointers, zero the struct elements and call + this ioctl again.</para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> +</refentry> diff --git a/Documentation/DocBook/media/v4l/media-types.xml b/Documentation/DocBook/media/v4l/media-types.xml new file mode 100644 index 000000000000..1af384250910 --- /dev/null +++ b/Documentation/DocBook/media/v4l/media-types.xml @@ -0,0 +1,240 @@ +<section id="media-controller-types"> +<title>Types and flags used to represent the media graph elements</title> + + <table frame="none" pgwide="1" id="media-entity-type"> + <title>Media entity types</title> + <tgroup cols="2"> + <colspec colname="c1"/> + <colspec colname="c2"/> + <tbody valign="top"> + <row> + <entry><constant>MEDIA_ENT_F_UNKNOWN</constant> and <constant>MEDIA_ENT_F_V4L2_SUBDEV_UNKNOWN</constant></entry> + <entry>Unknown entity. That generally indicates that + a driver didn't initialize properly the entity, with is a Kernel bug</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_IO_V4L</constant></entry> + <entry>Data streaming input and/or output entity.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_IO_VBI</constant></entry> + <entry>V4L VBI streaming input or output entity</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_IO_SWRADIO</constant></entry> + <entry>V4L Software Digital Radio (SDR) streaming input or output entity</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_IO_DTV</constant></entry> + <entry>DVB Digital TV streaming input or output entity</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_DTV_DEMOD</constant></entry> + <entry>Digital TV demodulator entity.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_TS_DEMUX</constant></entry> + <entry>MPEG Transport stream demux entity. Could be implemented on hardware or in Kernelspace by the Linux DVB subsystem.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_DTV_CA</constant></entry> + <entry>Digital TV Conditional Access module (CAM) entity</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_DTV_NET_DECAP</constant></entry> + <entry>Digital TV network ULE/MLE desencapsulation entity. Could be implemented on hardware or in Kernelspace</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_CONN_RF</constant></entry> + <entry>Connector for a Radio Frequency (RF) signal.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_CONN_SVIDEO</constant></entry> + <entry>Connector for a S-Video signal.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_CONN_COMPOSITE</constant></entry> + <entry>Connector for a RGB composite signal.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_CONN_TEST</constant></entry> + <entry>Connector for a test generator.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_CAM_SENSOR</constant></entry> + <entry>Camera video sensor entity.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_FLASH</constant></entry> + <entry>Flash controller entity.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_LENS</constant></entry> + <entry>Lens controller entity.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_ATV_DECODER</constant></entry> + <entry>Analog video decoder, the basic function of the video decoder + is to accept analogue video from a wide variety of sources such as + broadcast, DVD players, cameras and video cassette recorders, in + either NTSC, PAL, SECAM or HD format, separating the stream + into its component parts, luminance and chrominance, and output + it in some digital video standard, with appropriate timing + signals.</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_F_TUNER</constant></entry> + <entry>Digital TV, analog TV, radio and/or software radio tuner.</entry> + </row> + </tbody> + </tgroup> + </table> + + <table frame="none" pgwide="1" id="media-entity-flag"> + <title>Media entity flags</title> + <tgroup cols="2"> + <colspec colname="c1"/> + <colspec colname="c2"/> + <tbody valign="top"> + <row> + <entry><constant>MEDIA_ENT_FL_DEFAULT</constant></entry> + <entry>Default entity for its type. Used to discover the default + audio, VBI and video devices, the default camera sensor, ...</entry> + </row> + <row> + <entry><constant>MEDIA_ENT_FL_CONNECTOR</constant></entry> + <entry>The entity represents a data conector</entry> + </row> + </tbody> + </tgroup> + </table> + + <table frame="none" pgwide="1" id="media-intf-type"> + <title>Media interface types</title> + <tgroup cols="3"> + <colspec colname="c1"/> + <colspec colname="c2"/> + <colspec colname="c3"/> + <tbody valign="top"> + <row> + <entry><constant>MEDIA_INTF_T_DVB_FE</constant></entry> + <entry>Device node interface for the Digital TV frontend</entry> + <entry>typically, /dev/dvb/adapter?/frontend?</entry> + </row> + <row> + <entry><constant>MEDIA_INTF_T_DVB_DEMUX</constant></entry> + <entry>Device node interface for the Digital TV demux</entry> + <entry>typically, /dev/dvb/adapter?/demux?</entry> + </row> + <row> + <entry><constant>MEDIA_INTF_T_DVB_DVR</constant></entry> + <entry>Device node interface for the Digital TV DVR</entry> + <entry>typically, /dev/dvb/adapter?/dvr?</entry> + </row> + <row> + <entry><constant>MEDIA_INTF_T_DVB_CA</constant></entry> + <entry>Device node interface for the Digital TV Conditional Access</entry> + <entry>typically, /dev/dvb/adapter?/ca?</entry> + </row> + <row> + <entry><constant>MEDIA_INTF_T_DVB_FE</constant></entry> + <entry>Device node interface for the Digital TV network control</entry> + <entry>typically, /dev/dvb/adapter?/net?</entry> + </row> + <row> + <entry><constant>MEDIA_INTF_T_V4L_VIDEO</constant></entry> + <entry>Device node interface for video (V4L)</entry> + <entry>typically, /dev/video?</entry> + </row> + <row> + <entry><constant>MEDIA_INTF_T_V4L_VBI</constant></entry> + <entry>Device node interface for VBI (V4L)</entry> + <entry>typically, /dev/vbi?</entry> + </row> + <row> + <entry><constant>MEDIA_INTF_T_V4L_RADIO</constant></entry> + <entry>Device node interface for radio (V4L)</entry> + <entry>typically, /dev/vbi?</entry> + </row> + <row> + <entry><constant>MEDIA_INTF_T_V4L_SUBDEV</constant></entry> + <entry>Device node interface for a V4L subdevice</entry> + <entry>typically, /dev/v4l-subdev?</entry> + </row> + <row> + <entry><constant>MEDIA_INTF_T_V4L_SWRADIO</constant></entry> + <entry>Device node interface for Software Defined Radio (V4L)</entry> + <entry>typically, /dev/swradio?</entry> + </row> + </tbody> + </tgroup> + </table> + + <table frame="none" pgwide="1" id="media-pad-flag"> + <title>Media pad flags</title> + <tgroup cols="2"> + <colspec colname="c1"/> + <colspec colname="c2"/> + <tbody valign="top"> + <row> + <entry><constant>MEDIA_PAD_FL_SINK</constant></entry> + <entry>Input pad, relative to the entity. Input pads sink data and + are targets of links.</entry> + </row> + <row> + <entry><constant>MEDIA_PAD_FL_SOURCE</constant></entry> + <entry>Output pad, relative to the entity. Output pads source data + and are origins of links.</entry> + </row> + <row> + <entry><constant>MEDIA_PAD_FL_MUST_CONNECT</constant></entry> + <entry>If this flag is set and the pad is linked to any other + pad, then at least one of those links must be enabled for the + entity to be able to stream. There could be temporary reasons + (e.g. device configuration dependent) for the pad to need + enabled links even when this flag isn't set; the absence of the + flag doesn't imply there is none.</entry> + </row> + </tbody> + </tgroup> + </table> + + <para>One and only one of <constant>MEDIA_PAD_FL_SINK</constant> and + <constant>MEDIA_PAD_FL_SOURCE</constant> must be set for every pad.</para> + + <table frame="none" pgwide="1" id="media-link-flag"> + <title>Media link flags</title> + <tgroup cols="2"> + <colspec colname="c1"/> + <colspec colname="c2"/> + <tbody valign="top"> + <row> + <entry><constant>MEDIA_LNK_FL_ENABLED</constant></entry> + <entry>The link is enabled and can be used to transfer media data. + When two or more links target a sink pad, only one of them can be + enabled at a time.</entry> + </row> + <row> + <entry><constant>MEDIA_LNK_FL_IMMUTABLE</constant></entry> + <entry>The link enabled state can't be modified at runtime. An + immutable link is always enabled.</entry> + </row> + <row> + <entry><constant>MEDIA_LNK_FL_DYNAMIC</constant></entry> + <entry>The link enabled state can be modified during streaming. This + flag is set by drivers and is read-only for applications.</entry> + </row> + <row> + <entry><constant>MEDIA_LNK_FL_LINK_TYPE</constant></entry> + <entry><para>This is a bitmask that defines the type of the link. + Currently, two types of links are supported:</para> + <para><constant>MEDIA_LNK_FL_DATA_LINK</constant> + if the link is between two pads</para> + <para><constant>MEDIA_LNK_FL_INTERFACE_LINK</constant> + if the link is between an interface and an entity</para></entry> + </row> + </tbody> + </tgroup> + </table> + +</section> diff --git a/Documentation/DocBook/mtdnand.tmpl b/Documentation/DocBook/mtdnand.tmpl index 7da8f0402af5..b442921bca54 100644 --- a/Documentation/DocBook/mtdnand.tmpl +++ b/Documentation/DocBook/mtdnand.tmpl @@ -162,12 +162,15 @@ <sect1 id="Basic_defines"> <title>Basic defines</title> <para> - At least you have to provide a mtd structure and - a storage for the ioremap'ed chip address. - You can allocate the mtd structure using kmalloc - or you can allocate it statically. - In case of static allocation you have to allocate - a nand_chip structure too. + At least you have to provide a nand_chip structure + and a storage for the ioremap'ed chip address. + You can allocate the nand_chip structure using + kmalloc or you can allocate it statically. + The NAND chip structure embeds an mtd structure + which will be registered to the MTD subsystem. + You can extract a pointer to the mtd structure + from a nand_chip pointer using the nand_to_mtd() + helper. </para> <para> Kmalloc based example @@ -180,7 +183,6 @@ static void __iomem *baseaddr; Static example </para> <programlisting> -static struct mtd_info board_mtd; static struct nand_chip board_chip; static void __iomem *baseaddr; </programlisting> @@ -235,7 +237,7 @@ static void board_hwcontrol(struct mtd_info *mtd, int cmd) <programlisting> static void board_hwcontrol(struct mtd_info *mtd, int cmd) { - struct nand_chip *this = (struct nand_chip *) mtd->priv; + struct nand_chip *this = mtd_to_nand(mtd); switch(cmd){ case NAND_CTL_SETCLE: this->IO_ADDR_W |= CLE_ADRR_BIT; break; case NAND_CTL_CLRCLE: this->IO_ADDR_W &= ~CLE_ADRR_BIT; break; @@ -274,13 +276,15 @@ static int __init board_init (void) int err = 0; /* Allocate memory for MTD device structure and private data */ - board_mtd = kzalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), GFP_KERNEL); - if (!board_mtd) { + this = kzalloc(sizeof(struct nand_chip), GFP_KERNEL); + if (!this) { printk ("Unable to allocate NAND MTD device structure.\n"); err = -ENOMEM; goto out; } + board_mtd = nand_to_mtd(this); + /* map physical address */ baseaddr = ioremap(CHIP_PHYSICAL_ADDRESS, 1024); if (!baseaddr) { @@ -289,11 +293,6 @@ static int __init board_init (void) goto out_mtd; } - /* Get pointer to private data */ - this = (struct nand_chip *) (); - /* Link the private data with the MTD structure */ - board_mtd->priv = this; - /* Set address of NAND IO lines */ this->IO_ADDR_R = baseaddr; this->IO_ADDR_W = baseaddr; @@ -317,7 +316,7 @@ static int __init board_init (void) out_ior: iounmap(baseaddr); out_mtd: - kfree (board_mtd); + kfree (this); out: return err; } @@ -343,7 +342,7 @@ static void __exit board_cleanup (void) iounmap(baseaddr); /* Free the MTD device structure */ - kfree (board_mtd); + kfree (mtd_to_nand(board_mtd)); } module_exit(board_cleanup); #endif @@ -399,7 +398,7 @@ static void board_select_chip (struct mtd_info *mtd, int chip) <programlisting> static void board_select_chip (struct mtd_info *mtd, int chip) { - struct nand_chip *this = (struct nand_chip *) mtd->priv; + struct nand_chip *this = mtd_to_nand(mtd); /* Deselect all chips */ this->IO_ADDR_R &= ~BOARD_NAND_ADDR_MASK; diff --git a/Documentation/Makefile b/Documentation/Makefile index bc0548201755..1207d7907650 100644 --- a/Documentation/Makefile +++ b/Documentation/Makefile @@ -1,4 +1,4 @@ subdir-y := accounting auxdisplay blackfin connector \ filesystems filesystems ia64 laptops mic misc-devices \ - networking pcmcia prctl ptp spi timers vDSO video4linux \ + networking pcmcia prctl ptp timers vDSO video4linux \ watchdog diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt index 86302de67c2c..313dabdc14f9 100644 --- a/Documentation/devicetree/bindings/arm/arm,scpi.txt +++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt @@ -63,7 +63,7 @@ Required properties: - compatible : should be "arm,juno-sram-ns" for Non-secure SRAM on Juno The rest of the properties should follow the generic mmio-sram description -found in ../../misc/sysram.txt +found in ../../sram/sram.txt Each sub-node represents the reserved area for SCPI. diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 6aca64f289b6..c352c11bd641 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -157,6 +157,7 @@ nodes to be present and contain the properties described below. "arm,cortex-a17" "arm,cortex-a53" "arm,cortex-a57" + "arm,cortex-a72" "arm,cortex-m0" "arm,cortex-m0+" "arm,cortex-m1" diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt index a9adab84e2fe..a2c4f1d52492 100644 --- a/Documentation/devicetree/bindings/arm/psci.txt +++ b/Documentation/devicetree/bindings/arm/psci.txt @@ -23,17 +23,20 @@ Main node required properties: - compatible : should contain at least one of: - * "arm,psci" : for implementations complying to PSCI versions prior to - 0.2. For these cases function IDs must be provided. - - * "arm,psci-0.2" : for implementations complying to PSCI 0.2. Function - IDs are not required and should be ignored by an OS with PSCI 0.2 - support, but are permitted to be present for compatibility with - existing software when "arm,psci" is later in the compatible list. - - * "arm,psci-1.0" : for implementations complying to PSCI 1.0. PSCI 1.0 is - backward compatible with PSCI 0.2 with minor specification updates, - as defined in the PSCI specification[2]. + * "arm,psci" : For implementations complying to PSCI versions prior + to 0.2. + For these cases function IDs must be provided. + + * "arm,psci-0.2" : For implementations complying to PSCI 0.2. + Function IDs are not required and should be ignored by + an OS with PSCI 0.2 support, but are permitted to be + present for compatibility with existing software when + "arm,psci" is later in the compatible list. + + * "arm,psci-1.0" : For implementations complying to PSCI 1.0. + PSCI 1.0 is backward compatible with PSCI 0.2 with + minor specification updates, as defined in the PSCI + specification[2]. - method : The method of calling the PSCI firmware. Permitted values are: diff --git a/Documentation/devicetree/bindings/arm/secure.txt b/Documentation/devicetree/bindings/arm/secure.txt new file mode 100644 index 000000000000..e31303fb233a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/secure.txt @@ -0,0 +1,53 @@ +* ARM Secure world bindings + +ARM CPUs with TrustZone support have two distinct address spaces, +"Normal" and "Secure". Most devicetree consumers (including the Linux +kernel) are not TrustZone aware and run entirely in either the Normal +world or the Secure world. However some devicetree consumers are +TrustZone aware and need to be able to determine whether devices are +visible only in the Secure address space, only in the Normal address +space, or visible in both. (One example of that situation would be a +virtual machine which boots Secure firmware and wants to tell the +firmware about the layout of the machine via devicetree.) + +The general principle of the naming scheme for Secure world bindings +is that any property that needs a different value in the Secure world +can be supported by prefixing the property name with "secure-". So for +instance "secure-foo" would override "foo". For property names with +a vendor prefix, the Secure variant of "vendor,foo" would be +"vendor,secure-foo". If there is no "secure-" property then the Secure +world value is the same as specified for the Normal world by the +non-prefixed property. However, only the properties listed below may +validly have "secure-" versions; this list will be enlarged on a +case-by-case basis. + +Defining the bindings in this way means that a device tree which has +been annotated to indicate the presence of Secure-only devices can +still be processed unmodified by existing Non-secure software (and in +particular by the kernel). + +Note that it is still valid for bindings intended for purely Secure +world consumers (like kernels that run entirely in Secure) to simply +describe the view of Secure world using the standard bindings. These +secure- bindings only need to be used where both the Secure and Normal +world views need to be described in a single device tree. + +Valid Secure world properties: + +- secure-status : specifies whether the device is present and usable + in the secure world. The combination of this with "status" allows + the various possible combinations of device visibility to be + specified. If "secure-status" is not specified it defaults to the + same value as "status"; if "status" is not specified either then + both default to "okay". This means the following combinations are + possible: + + /* Neither specified: default to visible in both S and NS */ + secure-status = "okay"; /* visible in both */ + status = "okay"; /* visible in both */ + status = "okay"; secure-status = "okay"; /* visible in both */ + secure-status = "disabled"; /* NS-only */ + status = "okay"; secure-status = "disabled"; /* NS-only */ + status = "disabled"; secure-status = "okay"; /* S-only */ + status = "disabled"; /* disabled in both */ + status = "disabled"; secure-status = "disabled"; /* disabled in both */ diff --git a/Documentation/devicetree/bindings/clock/samsung,s2mps11.txt b/Documentation/devicetree/bindings/clock/samsung,s2mps11.txt new file mode 100644 index 000000000000..2726c1d58a79 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s2mps11.txt @@ -0,0 +1,49 @@ +Binding for Samsung S2M and S5M family clock generator block +============================================================ + +This is a part of device tree bindings for S2M and S5M family multi-function +devices. +More information can be found in bindings/mfd/sec-core.txt file. + +The S2MPS11/13/15 and S5M8767 provide three(AP/CP/BT) buffered 32.768 kHz +outputs. The S2MPS14 provides two (AP/BT) buffered 32.768 KHz outputs. + +To register these as clocks with common clock framework instantiate under +main device node a sub-node named "clocks". + +It uses the common clock binding documented in: + - Documentation/devicetree/bindings/clock/clock-bindings.txt + + +Required properties of the "clocks" sub-node: + - #clock-cells: should be 1. + - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", + "samsung,s2mps14-clk", "samsung,s5m8767-clk" + The S2MPS15 uses the same compatible as S2MPS13, as both provides similar + clocks. + + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + Clock ID Devices + ---------------------------------------------------------- + 32KhzAP 0 S2MPS11/13/14/15, S5M8767 + 32KhzCP 1 S2MPS11/13/15, S5M8767 + 32KhzBT 2 S2MPS11/13/14/15, S5M8767 + +Include dt-bindings/clock/samsung,s2mps11.h file to use preprocessor defines +in device tree sources. + + +Example: + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + + s2m_osc: clocks { + compatible = "samsung,s2mps11-clk"; + #clock-cells = <1>; + clock-output-names = "xx", "yy", "zz"; + }; + }; diff --git a/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt b/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt index 0715695e94a9..2aa06ac0fac5 100644 --- a/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt +++ b/Documentation/devicetree/bindings/cpufreq/arm_big_little_dt.txt @@ -12,7 +12,7 @@ must be present contiguously. Generic DT driver will check only node 'x' for cpu:x. Required properties: -- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt +- operating-points: Refer to Documentation/devicetree/bindings/opp/opp.txt for details Optional properties: diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt index e41c98ffbccb..dd3929e85dec 100644 --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt @@ -11,7 +11,7 @@ Required properties: - None Optional properties: -- operating-points: Refer to Documentation/devicetree/bindings/power/opp.txt for +- operating-points: Refer to Documentation/devicetree/bindings/opp/opp.txt for details. OPPs *must* be supplied either via DT, i.e. this property, or populated at runtime. - clock-latency: Specify the possible maximum transition latency for clock, diff --git a/Documentation/devicetree/bindings/display/bridge/tda998x.txt b/Documentation/devicetree/bindings/display/bridge/tda998x.txt index e9e4bce40760..e178e6b9f9ee 100644 --- a/Documentation/devicetree/bindings/display/bridge/tda998x.txt +++ b/Documentation/devicetree/bindings/display/bridge/tda998x.txt @@ -5,6 +5,10 @@ Required properties; - reg: I2C address +Required node: + - port: Input port node with endpoint definition, as described + in Documentation/devicetree/bindings/graph.txt + Optional properties: - interrupts: interrupt number and trigger type default: polling diff --git a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt index 040f365954cc..e7780a186a36 100644 --- a/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,usb-dmac.txt @@ -1,7 +1,13 @@ * Renesas USB DMA Controller Device Tree bindings Required Properties: -- compatible: must contain "renesas,usb-dmac" +-compatible: "renesas,<soctype>-usb-dmac", "renesas,usb-dmac" as fallback. + Examples with soctypes are: + - "renesas,r8a7790-usb-dmac" (R-Car H2) + - "renesas,r8a7791-usb-dmac" (R-Car M2-W) + - "renesas,r8a7793-usb-dmac" (R-Car M2-N) + - "renesas,r8a7794-usb-dmac" (R-Car E2) + - "renesas,r8a7795-usb-dmac" (R-Car H3) - reg: base address and length of the registers block for the DMAC - interrupts: interrupt specifiers for the DMAC, one for each entry in interrupt-names. @@ -15,7 +21,7 @@ Required Properties: Example: R8A7790 (R-Car H2) USB-DMACs usb_dmac0: dma-controller@e65a0000 { - compatible = "renesas,usb-dmac"; + compatible = "renesas,r8a7790-usb-dmac", "renesas,usb-dmac"; reg = <0 0xe65a0000 0 0x100>; interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH 0 109 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/dma/stm32-dma.txt b/Documentation/devicetree/bindings/dma/stm32-dma.txt new file mode 100644 index 000000000000..70cd13f1588a --- /dev/null +++ b/Documentation/devicetree/bindings/dma/stm32-dma.txt @@ -0,0 +1,82 @@ +* STMicroelectronics STM32 DMA controller + +The STM32 DMA is a general-purpose direct memory access controller capable of +supporting 8 independent DMA channels. Each channel can have up to 8 requests. + +Required properties: +- compatible: Should be "st,stm32-dma" +- reg: Should contain DMA registers location and length. This should include + all of the per-channel registers. +- interrupts: Should contain all of the per-channel DMA interrupts in + ascending order with respect to the DMA channel index. +- clocks: Should contain the input clock of the DMA instance. +- #dma-cells : Must be <4>. See DMA client paragraph for more details. + +Optional properties: +- resets: Reference to a reset controller asserting the DMA controller +- st,mem2mem: boolean; if defined, it indicates that the controller supports + memory-to-memory transfer + +Example: + + dma2: dma-controller@40026400 { + compatible = "st,stm32-dma"; + reg = <0x40026400 0x400>; + interrupts = <56>, + <57>, + <58>, + <59>, + <60>, + <68>, + <69>, + <70>; + clocks = <&clk_hclk>; + #dma-cells = <4>; + st,mem2mem; + resets = <&rcc 150>; + }; + +* DMA client + +DMA clients connected to the STM32 DMA controller must use the format +described in the dma.txt file, using a five-cell specifier for each +channel: a phandle plus four integer cells. +The four cells in order are: + +1. The channel id +2. The request line number +3. A 32bit mask specifying the DMA channel configuration which are device + dependent: + -bit 9: Peripheral Increment Address + 0x0: no address increment between transfers + 0x1: increment address between transfers + -bit 10: Memory Increment Address + 0x0: no address increment between transfers + 0x1: increment address between transfers + -bit 15: Peripheral Increment Offset Size + 0x0: offset size is linked to the peripheral bus width + 0x1: offset size is fixed to 4 (32-bit alignment) + -bit 16-17: Priority level + 0x0: low + 0x1: medium + 0x2: high + 0x3: very high +5. A 32bit mask specifying the DMA FIFO threshold configuration which are device + dependent: + -bit 0-1: Fifo threshold + 0x0: 1/4 full FIFO + 0x1: 1/2 full FIFO + 0x2: 3/4 full FIFO + 0x3: full FIFO + +Example: + + usart1: serial@40011000 { + compatible = "st,stm32-usart", "st,stm32-uart"; + reg = <0x40011000 0x400>; + interrupts = <37>; + clocks = <&clk_pclk2>; + dmas = <&dma2 2 4 0x10400 0x3>, + <&dma2 7 5 0x10200 0x3>; + dma-names = "rx", "tx"; + }; diff --git a/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt b/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt index b152a75dceae..aead5869a28d 100644 --- a/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt +++ b/Documentation/devicetree/bindings/dma/ti-dma-crossbar.txt @@ -14,6 +14,10 @@ The DMA controller node need to have the following poroperties: Optional properties: - ti,dma-safe-map: Safe routing value for unused request lines +- ti,reserved-dma-request-ranges: DMA request ranges which should not be used + when mapping xbar input to DMA request, they are either + allocated to be used by for example the DSP or they are used as + memcpy channels in eDMA. Notes: When requesting channel via ti,dra7-dma-crossbar, the DMA clinet must request @@ -46,6 +50,8 @@ sdma_xbar: dma-router@4a002b78 { #dma-cells = <1>; dma-requests = <205>; ti,dma-safe-map = <0>; + /* Protect the sDMA request ranges: 10-14 and 100-126 */ + ti,reserved-dma-request-ranges = <10 5>, <100 27>; dma-masters = <&sdma>; }; diff --git a/Documentation/devicetree/bindings/eeprom/eeprom.txt b/Documentation/devicetree/bindings/eeprom/eeprom.txt index 4342c10de1bf..735bc94444bb 100644 --- a/Documentation/devicetree/bindings/eeprom/eeprom.txt +++ b/Documentation/devicetree/bindings/eeprom/eeprom.txt @@ -2,11 +2,22 @@ EEPROMs (I2C) Required properties: - - compatible : should be "<manufacturer>,<type>" - If there is no specific driver for <manufacturer>, a generic - driver based on <type> is selected. Possible types are: - 24c00, 24c01, 24c02, 24c04, 24c08, 24c16, 24c32, 24c64, - 24c128, 24c256, 24c512, 24c1024, spd + - compatible : should be "<manufacturer>,<type>", like these: + + "atmel,24c00", "atmel,24c01", "atmel,24c02", "atmel,24c04", + "atmel,24c08", "atmel,24c16", "atmel,24c32", "atmel,24c64", + "atmel,24c128", "atmel,24c256", "atmel,24c512", "atmel,24c1024" + + "catalyst,24c32" + + "ramtron,24c64" + + "renesas,r1ex24002" + + If there is no specific driver for <manufacturer>, a generic + driver based on <type> is selected. Possible types are: + "24c00", "24c01", "24c02", "24c04", "24c08", "24c16", "24c32", "24c64", + "24c128", "24c256", "24c512", "24c1024", "spd" - reg : the I2C address of the EEPROM diff --git a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt index e1705fae63a8..e27341f8a4c7 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-arizona.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-arizona.txt @@ -13,3 +13,63 @@ Optional properties: ARIZONA_ACCDET_MODE_HPR or 2 - Headphone detect mode is set to HPDETR If this node is not mentioned or if the value is unknown, then headphone detection mode is set to HPDETL. + + - wlf,use-jd2 : Use the additional JD input along with JD1 for dual pin jack + detection. + - wlf,use-jd2-nopull : Internal pull on JD2 is disabled when used for + jack detection. + - wlf,jd-invert : Invert the polarity of the jack detection switch + + - wlf,micd-software-compare : Use a software comparison to determine mic + presence + - wlf,micd-detect-debounce : Additional software microphone detection + debounce specified in milliseconds. + - wlf,micd-pol-gpio : GPIO specifier for the GPIO controlling the headset + polarity if one exists. + - wlf,micd-bias-start-time : Time allowed for MICBIAS to startup prior to + performing microphone detection, specified as per the ARIZONA_MICD_TIME_XXX + defines. + - wlf,micd-rate : Delay between successive microphone detection measurements, + specified as per the ARIZONA_MICD_TIME_XXX defines. + - wlf,micd-dbtime : Microphone detection hardware debounces specified as the + number of measurements to take, valid values being 2 and 4. + - wlf,micd-timeout-ms : Timeout for microphone detection, specified in + milliseconds. + - wlf,micd-force-micbias : Force MICBIAS continuously on during microphone + detection. + - wlf,micd-configs : Headset polarity configurations (generally used for + detection of CTIA / OMTP headsets), the field can be of variable length + but should always be a multiple of 3 cells long, each three cell group + represents one polarity configuration. + The first cell defines the accessory detection pin, zero will use MICDET1 + and all other values will use MICDET2. + The second cell represents the MICBIAS to be used. + The third cell represents the value of the micd-pol-gpio pin. + + - wlf,gpsw : Settings for the general purpose switch + +Example: + +codec: wm8280@0 { + compatible = "wlf,wm8280"; + reg = <0>; + ... + + wlf,use-jd2; + wlf,use-jd2-nopull; + wlf,jd-invert; + + wlf,micd-software-compare; + wlf,micd-detect-debounce = <0>; + wlf,micd-pol-gpio = <&codec 2 0>; + wlf,micd-rate = <ARIZONA_MICD_TIME_8MS>; + wlf,micd-dbtime = <4>; + wlf,micd-timeout-ms = <100>; + wlf,micd-force-micbias; + wlf,micd-configs = < + 0 1 0 /* MICDET1 MICBIAS1 GPIO=low */ + 1 2 1 /* MICDET2 MICBIAS2 GPIO=high */ + >; + + wlf,gpsw = <0>; +}; diff --git a/Documentation/devicetree/bindings/extcon/extcon-max3355.txt b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt new file mode 100644 index 000000000000..f2288ea9eb82 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt @@ -0,0 +1,21 @@ +Maxim Integrated MAX3355 USB OTG chip +------------------------------------- + +MAX3355 integrates a charge pump and comparators to enable a system with an +integrated USB OTG dual-role transceiver to function as a USB OTG dual-role +device. + +Required properties: +- compatible: should be "maxim,max3355"; +- maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's SHDN# pin; +- id-gpios: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's ID_OUT pin. + +Example: + + usb-otg { + compatible = "maxim,max3355"; + maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt index dd5d2c0394b1..4d6c8cdc8586 100644 --- a/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/snps-dwapb-gpio.txt @@ -24,7 +24,7 @@ controller. - #interrupt-cells : Specifies the number of cells needed to encode an interrupt. Shall be set to 2. The first cell defines the interrupt number, the second encodes the triger flags encoded as described in - Documentation/devicetree/bindings/interrupts.txt + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - interrupt-parent : The parent interrupt controller. - interrupts : The interrupt to the parent controller raised when GPIOs generate the interrupts. diff --git a/Documentation/devicetree/bindings/i2c/i2c-at91.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt index 6e81dc153f3b..ef973a0343c7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-at91.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt @@ -3,7 +3,7 @@ I2C for Atmel platforms Required properties : - compatible : Must be "atmel,at91rm9200-i2c", "atmel,at91sam9261-i2c", "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c", - "atmel,at91sam9x5-i2c" or "atmel,sama5d2-i2c" + "atmel,at91sam9x5-i2c", "atmel,sama5d4-i2c" or "atmel,sama5d2-i2c" - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt number to the cpu. @@ -17,6 +17,8 @@ Optional properties: - dma-names: should contain "tx" and "rx". - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO capable I2C controllers. +- i2c-sda-hold-time-ns: TWD hold time, only available for "atmel,sama5d4-i2c" + and "atmel,sama5d2-i2c". - Child nodes conforming to i2c bus binding Examples : @@ -52,6 +54,7 @@ i2c0: i2c@f8034600 { #size-cells = <0>; clocks = <&flx0>; atmel,fifo-size = <16>; + i2c-sda-hold-time-ns = <336>; wm8731: wm8731@1a { compatible = "wm8731"; diff --git a/Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt b/Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt index d6f724efdcf2..aeceaceba3c5 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt @@ -2,7 +2,7 @@ Broadcom stb bsc iic master controller Required properties: -- compatible: should be "brcm,brcmstb-i2c" +- compatible: should be "brcm,brcmstb-i2c" or "brcm,brcmper-i2c" - clock-frequency: 32-bit decimal value of iic master clock freqency in Hz valid values are 375000, 390000, 187500, 200000 93750, 97500, 46875 and 50000 diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index ea406eb20fa5..95e97223a71c 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -20,6 +20,10 @@ Optional properties: propoerty indicates the default frequency 100 kHz. - clocks: clock specifier. +- i2c-scl-falling-time-ns: see i2c.txt +- i2c-scl-internal-delay-ns: see i2c.txt +- i2c-scl-rising-time-ns: see i2c.txt + Examples : i2c0: i2c@e6508000 { diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt index 8a99150ac3a7..c8d977ed847f 100644 --- a/Documentation/devicetree/bindings/i2c/i2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c.txt @@ -29,12 +29,38 @@ Optional properties These properties may not be supported by all drivers. However, if a driver wants to support one of the below features, it should adapt the bindings below. -- clock-frequency - frequency of bus clock in Hz. -- wakeup-source - device can be used as a wakeup source. +- clock-frequency + frequency of bus clock in Hz. -- interrupts - interrupts used by the device. -- interrupt-names - "irq" and "wakeup" names are recognized by I2C core, - other names are left to individual drivers. +- i2c-scl-falling-time-ns + Number of nanoseconds the SCL signal takes to fall; t(f) in the I2C + specification. + +- i2c-scl-internal-delay-ns + Number of nanoseconds the IP core additionally needs to setup SCL. + +- i2c-scl-rising-time-ns + Number of nanoseconds the SCL signal takes to rise; t(r) in the I2C + specification. + +- i2c-sda-falling-time-ns + Number of nanoseconds the SDA signal takes to fall; t(f) in the I2C + specification. + +- interrupts + interrupts used by the device. + +- interrupt-names + "irq" and "wakeup" names are recognized by I2C core, other names are + left to individual drivers. + +- multi-master + states that there is another master active on this bus. The OS can use + this information to adapt power management to keep the arbitration awake + all the time, for example. + +- wakeup-source + device can be used as a wakeup source. Binding may contain optional "interrupts" property, describing interrupts used by the device. I2C core will assign "irq" interrupt (or the very first diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index c50cf13c852e..539874490492 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -20,22 +20,11 @@ adi,adt7476 +/-1C TDM Extended Temp Range I.C adi,adt7490 +/-1C TDM Extended Temp Range I.C adi,adxl345 Three-Axis Digital Accelerometer adi,adxl346 Three-Axis Digital Accelerometer (backward-compatibility value "adi,adxl345" must be listed too) +ams,iaq-core AMS iAQ-Core VOC Sensor at,24c08 i2c serial eeprom (24cxx) -atmel,24c00 i2c serial eeprom (24cxx) -atmel,24c01 i2c serial eeprom (24cxx) -atmel,24c02 i2c serial eeprom (24cxx) -atmel,24c04 i2c serial eeprom (24cxx) -atmel,24c16 i2c serial eeprom (24cxx) -atmel,24c32 i2c serial eeprom (24cxx) -atmel,24c64 i2c serial eeprom (24cxx) -atmel,24c128 i2c serial eeprom (24cxx) -atmel,24c256 i2c serial eeprom (24cxx) -atmel,24c512 i2c serial eeprom (24cxx) -atmel,24c1024 i2c serial eeprom (24cxx) atmel,at97sc3204t i2c trusted platform module (TPM) capella,cm32181 CM32181: Ambient Light Sensor capella,cm3232 CM3232: Ambient Light Sensor -catalyst,24c32 i2c serial eeprom cirrus,cs42l51 Cirrus Logic CS42L51 audio codec dallas,ds1307 64 x 8, Serial, I2C Real-Time Clock dallas,ds1338 I2C RTC with 56-Byte NV RAM @@ -49,11 +38,13 @@ dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat dlg,da9053 DA9053: flexible system level PMIC with multicore support dlg,da9063 DA9063: system PMIC for quad-core application processors +epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer +fsl,mpl3115 MPL3115: Absolute Digital Pressure Sensor fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface @@ -80,7 +71,6 @@ ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI an pericom,pt7c4338 Real-time Clock Module plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch pulsedlight,lidar-lite-v2 Pulsedlight LIDAR range-finding sensor -ramtron,24c64 i2c serial eeprom (24cxx) ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt index e3c37467d7da..3c10e8581144 100644 --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -7,13 +7,18 @@ Required properties: * "fsl,mma8453" * "fsl,mma8652" * "fsl,mma8653" + - reg: the I2C address of the chip Optional properties: - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: interrupt mapping for GPIO IRQ + - interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's + interrupt line in use. + Example: mma8453fc@1d { @@ -21,4 +26,5 @@ Example: reg = <0x1d>; interrupt-parent = <&gpio1>; interrupts = <5 0>; + interrupt-names = "INT2"; }; diff --git a/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt new file mode 100644 index 000000000000..5c184b940669 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/imx7d-adc.txt @@ -0,0 +1,22 @@ +Freescale imx7d ADC bindings + +The devicetree bindings are for the ADC driver written for +imx7d SoC. + +Required properties: +- compatible: Should be "fsl,imx7d-adc" +- reg: Offset and length of the register set for the ADC device +- interrupts: The interrupt number for the ADC device +- clocks: The root clock of the ADC controller +- clock-names: Must contain "adc", matching entry in the clocks property +- vref-supply: The regulator supply ADC reference voltage + +Example: +adc1: adc@30610000 { + compatible = "fsl,imx7d-adc"; + reg = <0x30610000 0x10000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ADC_ROOT_CLK>; + clock-names = "adc"; + vref-supply = <®_vcc_3v3_mcu>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt index 2a1f3af30155..bcd3ac8e6e0c 100644 --- a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt +++ b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt @@ -10,16 +10,28 @@ must be specified. Required properties: - compatible: Must be one of the following, depending on the model: - "mcp3001" - "mcp3002" - "mcp3004" - "mcp3008" - "mcp3201" - "mcp3202" - "mcp3204" - "mcp3208" - "mcp3301" + "mcp3001" (DEPRECATED) + "mcp3002" (DEPRECATED) + "mcp3004" (DEPRECATED) + "mcp3008" (DEPRECATED) + "mcp3201" (DEPRECATED) + "mcp3202" (DEPRECATED) + "mcp3204" (DEPRECATED) + "mcp3208" (DEPRECATED) + "mcp3301" (DEPRECATED) + "microchip,mcp3001" + "microchip,mcp3002" + "microchip,mcp3004" + "microchip,mcp3008" + "microchip,mcp3201" + "microchip,mcp3202" + "microchip,mcp3204" + "microchip,mcp3208" + "microchip,mcp3301" + + NOTE: The use of the compatibles with no vendor prefix + is deprecated and only listed because old DT use them. Examples: spi_controller { diff --git a/Documentation/devicetree/bindings/iio/adc/mcp3422.txt b/Documentation/devicetree/bindings/iio/adc/mcp3422.txt index 333139cc0bfb..dcae4ccfcc52 100644 --- a/Documentation/devicetree/bindings/iio/adc/mcp3422.txt +++ b/Documentation/devicetree/bindings/iio/adc/mcp3422.txt @@ -1,7 +1,8 @@ -* Microchip mcp3422/3/4/6/7/8 chip family (ADC) +* Microchip mcp3421/2/3/4/6/7/8 chip family (ADC) Required properties: - compatible: Should be + "microchip,mcp3421" or "microchip,mcp3422" or "microchip,mcp3423" or "microchip,mcp3424" or diff --git a/Documentation/devicetree/bindings/iio/adc/palmas-gpadc.txt b/Documentation/devicetree/bindings/iio/adc/palmas-gpadc.txt new file mode 100644 index 000000000000..4bb9a86065d1 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/palmas-gpadc.txt @@ -0,0 +1,48 @@ +* Palmas general purpose ADC IP block devicetree bindings + +Channels list: + 0 battery type + 1 battery temp NTC (optional current source) + 2 GP + 3 temp (with ext. diode, optional current source) + 4 GP + 5 GP + 6 VBAT_SENSE + 7 VCC_SENSE + 8 Backup Battery voltage + 9 external charger (VCHG) + 10 VBUS + 11 DC-DC current probe (how does this work?) + 12 internal die temp + 13 internal die temp + 14 USB ID pin voltage + 15 test network + +Required properties: +- compatible : Must be "ti,palmas-gpadc". +- #io-channel-cells: Should be set to <1>. + +Optional sub-nodes: +ti,channel0-current-microamp: Channel 0 current in uA. + Values are rounded to derive 0uA, 5uA, 15uA, 20uA. +ti,channel3-current-microamp: Channel 3 current in uA. + Values are rounded to derive 0uA, 10uA, 400uA, 800uA. +ti,enable-extended-delay: Enable extended delay. + +Example: + +pmic { + compatible = "ti,twl6035-pmic", "ti,palmas-pmic"; + ... + gpadc { + compatible = "ti,palmas-gpadc"; + interrupts = <18 0 + 16 0 + 17 0>; + #io-channel-cells = <1>; + ti,channel0-current-microamp = <5>; + ti,channel3-current-microamp = <10>; + }; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt index 15ca6b47958e..daa2b2c29428 100644 --- a/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt @@ -1,7 +1,7 @@ -* Texas Instruments' ADC128S052 and ADC122S021 ADC chip +* Texas Instruments' ADC128S052, ADC122S021 and ADC124S021 ADC chip Required properties: - - compatible: Should be "ti,adc128s052" or "ti,adc122s021" + - compatible: Should be "ti,adc128s052", "ti,adc122s021" or "ti,adc124s021" - reg: spi chip select number for the device - vref-supply: The regulator supply for ADC reference voltage diff --git a/Documentation/devicetree/bindings/iio/adc/ti-ads8688.txt b/Documentation/devicetree/bindings/iio/adc/ti-ads8688.txt new file mode 100644 index 000000000000..a02337d7efa4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-ads8688.txt @@ -0,0 +1,20 @@ +* Texas Instruments' ADS8684 and ADS8688 ADC chip + +Required properties: + - compatible: Should be "ti,ads8684" or "ti,ads8688" + - reg: spi chip select number for the device + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: + - vref-supply: The regulator supply for ADC reference voltage + +Example: +adc@0 { + compatible = "ti,ads8688"; + reg = <0>; + vref-supply = <&vdd_supply>; + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/health/max30100.txt b/Documentation/devicetree/bindings/iio/health/max30100.txt new file mode 100644 index 000000000000..f6fbac66ad06 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/health/max30100.txt @@ -0,0 +1,21 @@ +Maxim MAX30100 heart rate and pulse oximeter sensor + +* https://datasheets.maximintegrated.com/en/ds/MAX30100.pdf + +Required properties: + - compatible: must be "maxim,max30100" + - reg: the I2C address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic + interrupt client node bindings. + +Example: + +max30100@057 { + compatible = "maxim,max30100"; + reg = <57>; + interrupt-parent = <&gpio1>; + interrupts = <16 2>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/us5182d.txt b/Documentation/devicetree/bindings/iio/light/us5182d.txt index 6f0a530144fd..a61979997f37 100644 --- a/Documentation/devicetree/bindings/iio/light/us5182d.txt +++ b/Documentation/devicetree/bindings/iio/light/us5182d.txt @@ -7,13 +7,24 @@ Required properties: Optional properties: - upisemi,glass-coef: glass attenuation factor - compensation factor of resolution 1000 for material transmittance. + - upisemi,dark-ths: array of 8 elements containing 16-bit thresholds (adc counts) corresponding to every scale. + - upisemi,upper-dark-gain: 8-bit dark gain compensation factor(4 int and 4 fractional bits - Q4.4) applied when light > threshold + - upisemi,lower-dark-gain: 8-bit dark gain compensation factor(4 int and 4 fractional bits - Q4.4) applied when light < threshold +- upisemi,continuous: This chip has two power modes: one-shot (chip takes one + measurement and then shuts itself down) and continuous ( + chip takes continuous measurements). The one-shot mode is + more power-friendly but the continuous mode may be more + reliable. If this property is specified the continuous + mode will be used instead of the default one-shot one for + raw reads. + If the optional properties are not specified these factors will default to the values in the below example. The glass-coef defaults to no compensation for the covering material. diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index d3ccdb190c53..d4b87cc1e446 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -36,6 +36,7 @@ Accelerometers: - st,lsm303dlm-accel - st,lsm330-accel - st,lsm303agr-accel +- st,lis2dh12-accel Gyroscopes: - st,l3g4200d-gyro diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt index 8ba98eec765b..c98757a69110 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt @@ -13,6 +13,17 @@ Required properties: - interrupt-parent : Interrupt controller to which the chip is connected - interrupts : Interrupt to which the chip is connected +Optional properties: + + - irq-gpios : GPIO pin used for IRQ. The driver uses the + interrupt gpio pin as output to reset the device. + - reset-gpios : GPIO pin used for reset + + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + (swapping is done after inverting the axis) + Example: i2c@00000000 { @@ -23,6 +34,9 @@ Example: reg = <0x5d>; interrupt-parent = <&gpio>; interrupts = <0 0>; + + irq-gpios = <&gpio1 0 0>; + reset-gpios = <&gpio1 1 0>; }; /* ... */ diff --git a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt index 8eb240a287c8..697a3e7831e7 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt @@ -9,7 +9,9 @@ Required properties: - touchscreen-size-y: vertical resolution of touchscreen (in pixels) Optional properties: -- reset-gpio: GPIO connected to the RESET line of the chip +- reset-gpios: GPIO connected to the RESET line of the chip +- enable-gpios: GPIO connected to the ENABLE line of the chip +- wake-gpios: GPIO connected to the WAKE line of the chip Example: diff --git a/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt new file mode 100644 index 000000000000..4c1c092c276b --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt @@ -0,0 +1,11 @@ +* TS-4800 Touchscreen bindings + +Required properties: +- compatible: must be "technologic,ts4800-ts" +- reg: physical base address of the controller and length of memory mapped + region. +- syscon: phandle / integers array that points to the syscon node which + describes the FPGA's syscon registers. + - phandle to FPGA's syscon + - offset to the touchscreen register + - offset to the touchscreen enable bit diff --git a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt index ec96b1f01478..475ae9bd562b 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt @@ -22,7 +22,7 @@ Interrupt Controllers bindings used by client devices. Example: interrupt-controller@18060010 { - compatible = "qca,ar9132-misc-intc", qca,ar7100-misc-intc"; + compatible = "qca,ar9132-misc-intc", "qca,ar7100-misc-intc"; reg = <0x18060010 0x4>; interrupt-parent = <&cpuintc>; diff --git a/Documentation/devicetree/bindings/media/i2c/adp1653.txt b/Documentation/devicetree/bindings/media/i2c/adp1653.txt index 5ce66f2104e3..4cce0de40ee9 100644 --- a/Documentation/devicetree/bindings/media/i2c/adp1653.txt +++ b/Documentation/devicetree/bindings/media/i2c/adp1653.txt @@ -12,12 +12,13 @@ There are two LED outputs available - flash and indicator. One LED is represented by one child node, nodes need to be named "flash" and "indicator". Required properties of the LED child node: -- max-microamp : see Documentation/devicetree/bindings/leds/common.txt +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt Required properties of the flash LED child node: - flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt - flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt Example: @@ -29,9 +30,9 @@ Example: flash { flash-timeout-us = <500000>; flash-max-microamp = <320000>; - max-microamp = <50000>; + led-max-microamp = <50000>; }; indicator { - max-microamp = <17500>; + led-max-microamp = <17500>; }; }; diff --git a/Documentation/devicetree/bindings/memory-controllers/ath79-ddr-controller.txt b/Documentation/devicetree/bindings/memory-controllers/ath79-ddr-controller.txt index efe35a065714..c81af75bcd88 100644 --- a/Documentation/devicetree/bindings/memory-controllers/ath79-ddr-controller.txt +++ b/Documentation/devicetree/bindings/memory-controllers/ath79-ddr-controller.txt @@ -1,6 +1,6 @@ Binding for Qualcomm Atheros AR7xxx/AR9xxx DDR controller -The DDR controller of the ARxxx and AR9xxx families provides an interface +The DDR controller of the AR7xxx and AR9xxx families provides an interface to flush the FIFO between various devices and the DDR. This is mainly used by the IRQ controller to flush the FIFO before running the interrupt handler of such devices. @@ -11,9 +11,9 @@ Required properties: "qca,[ar7100|ar7240]-ddr-controller" as fallback. On SoC with PCI support "qca,ar7100-ddr-controller" should be used as fallback, otherwise "qca,ar7240-ddr-controller" should be used. -- reg: Base address and size of the controllers memory area -- #qca,ddr-wb-channel-cells: has to be 1, the index of the write buffer - channel +- reg: Base address and size of the controller's memory area +- #qca,ddr-wb-channel-cells: Specifies the number of cells needed to encode + the write buffer channel index, should be 1. Example: diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index 18be0cbfb456..9b30011ecabe 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -1,4 +1,4 @@ -Wolfson Arizona class audio SoCs +Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs These devices are audio SoCs with extensive digital capabilites and a range of analogue I/O. @@ -6,12 +6,14 @@ of analogue I/O. Required properties: - compatible : One of the following chip-specific strings: + "cirrus,cs47l24" "wlf,wm5102" "wlf,wm5110" "wlf,wm8280" "wlf,wm8997" "wlf,wm8998" "wlf,wm1814" + "wlf,wm1831" - reg : I2C slave address when connected using I2C, chip select number when using SPI. @@ -24,7 +26,7 @@ Required properties: - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. The first cell is the IRQ number. The second cell is the flags, encoded as the trigger masks from - Documentation/devicetree/bindings/interrupts.txt + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - gpio-controller : Indicates this device is a GPIO controller. - #gpio-cells : Must be 2. The first cell is the pin number and the @@ -41,10 +43,21 @@ Required properties: - SPKVDD-supply : Speaker driver power supply (wm8997) + - DCVDD-supply : Main power supply (cs47l24, wm1831) + + - MICVDD-supply : Microphone power supply (cs47l24, wm1831) + Optional properties: - wlf,reset : GPIO specifier for the GPIO controlling /RESET + - clocks: Should reference the clocks supplied on MCLK1 and MCLK2 + - clock-names: Should contains two strings: + "mclk1" for the clock supplied on MCLK1, recommended to be a high + quality audio reference clock + "mclk2" for the clock supplied on MCLK2, recommended to be an always on + 32k clock + - wlf,gpio-defaults : A list of GPIO configuration register values. Defines for the appropriate values can found in <dt-bindings/mfd/arizona.txt>. If absent, no configuration of these registers is performed. If any entry has @@ -59,6 +72,12 @@ Optional properties: that have not been specified are set to 0 by default. Entries are: <IN1, IN2, IN3, IN4> (wm5102, wm5110, wm8280, wm8997) <IN1A, IN2A, IN1B, IN2B> (wm8998, wm1814) + - wlf,out-mono : A list of boolean values indicating whether each output is + mono or stereo. Position within the list indicates the output affected + (eg. First entry in the list corresponds to output 1). A non-zero value + indicates a mono output. If present, the number of values should be less + than or equal to the number of outputs, if less values are supplied the + additional outputs will be treated as stereo. - wlf,dmic-ref : DMIC reference voltage source for each input, can be selected from either MICVDD or one of the MICBIAS's, defines @@ -69,6 +88,7 @@ Optional properties: - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if they are being externally supplied. As covered in Documentation/devicetree/bindings/regulator/regulator.txt + (wm5102, wm5110, wm8280, wm8997, wm8998, wm1814) Also see child specific device properties: Regulator - ../regulator/arizona-regulator.txt diff --git a/Documentation/devicetree/bindings/mfd/palmas.txt b/Documentation/devicetree/bindings/mfd/palmas.txt index eda898978d33..8ae1a32bfb7e 100644 --- a/Documentation/devicetree/bindings/mfd/palmas.txt +++ b/Documentation/devicetree/bindings/mfd/palmas.txt @@ -24,7 +24,7 @@ and also the generic series names - #interrupt-cells : should be set to 2 for IRQ number and flags The first cell is the IRQ number. The second cell is the flags, encoded as the trigger masks from - Documentation/devicetree/bindings/interrupts.txt + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - interrupt-parent : The parent interrupt controller. Optional properties: diff --git a/Documentation/devicetree/bindings/mfd/s2mpa01.txt b/Documentation/devicetree/bindings/mfd/s2mpa01.txt deleted file mode 100644 index c13d3d8c3947..000000000000 --- a/Documentation/devicetree/bindings/mfd/s2mpa01.txt +++ /dev/null @@ -1,90 +0,0 @@ - -* Samsung S2MPA01 Voltage and Current Regulator - -The Samsung S2MPA01 is a multi-function device which includes high -efficiency buck converters including Dual-Phase buck converter, various LDOs, -and an RTC. It is interfaced to the host controller using an I2C interface. -Each sub-block is addressed by the host system using different I2C slave -addresses. - -Required properties: -- compatible: Should be "samsung,s2mpa01-pmic". -- reg: Specifies the I2C slave address of the PMIC block. It should be 0x66. - -Optional properties: -- interrupt-parent: Specifies the phandle of the interrupt controller to which - the interrupts from s2mpa01 are delivered to. -- interrupts: An interrupt specifier for the sole interrupt generated by the - device. - -Optional nodes: -- regulators: The regulators of s2mpa01 that have to be instantiated should be - included in a sub-node named 'regulators'. Regulator nodes and constraints - included in this sub-node use the standard regulator bindings which are - documented elsewhere. - -Properties for BUCK regulator nodes: -- regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500 - (default), 25000, or 50000. May be 0 for disabling the ramp delay on - BUCK{1,2,3,4}. - - In the absence of the regulator-ramp-delay property, the default ramp - delay will be used. - - NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set - for a particular group of BUCKs. So provide same regulator-ramp-delay=<value>. - - The following BUCKs share ramp settings: - * 1 and 6 - * 2 and 4 - * 8, 9, and 10 - -The following are the names of the regulators that the s2mpa01 PMIC block -supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number -as per the datasheet of s2mpa01. - - - LDOn - - valid values for n are 1 to 26 - - Example: LDO1, LD02, LDO26 - - BUCKn - - valid values for n are 1 to 10. - - Example: BUCK1, BUCK2, BUCK9 - -Example: - - s2mpa01_pmic@66 { - compatible = "samsung,s2mpa01-pmic"; - reg = <0x66>; - - regulators { - ldo1_reg: LDO1 { - regulator-name = "VDD_ALIVE"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - }; - - ldo2_reg: LDO2 { - regulator-name = "VDDQ_MMC2"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - }; - - buck1_reg: BUCK1 { - regulator-name = "vdd_mif"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - buck2_reg: BUCK2 { - regulator-name = "vdd_arm"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - regulator-ramp-delay = <50000>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt deleted file mode 100644 index 09b94c97faac..000000000000 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ /dev/null @@ -1,153 +0,0 @@ - -* Samsung S2MPS11/13/14/15 and S2MPU02 Voltage and Current Regulator - -The Samsung S2MPS11 is a multi-function device which includes voltage and -current regulators, RTC, charger controller and other sub-blocks. It is -interfaced to the host controller using an I2C interface. Each sub-block is -addressed by the host system using different I2C slave addresses. - -Required properties: -- compatible: Should be one of the following - - "samsung,s2mps11-pmic" - - "samsung,s2mps13-pmic" - - "samsung,s2mps14-pmic" - - "samsung,s2mps15-pmic" - - "samsung,s2mpu02-pmic". -- reg: Specifies the I2C slave address of the pmic block. It should be 0x66. - -Optional properties: -- interrupt-parent: Specifies the phandle of the interrupt controller to which - the interrupts from s2mps11 are delivered to. -- interrupts: Interrupt specifiers for interrupt sources. -- samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled - down. When the system is suspended it will always go down thus triggerring - unwanted buck warm reset (setting buck voltages to default values). -- samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is - connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1 - register to turn off the power. Usually the ACOKB is pulled up to VBATT so - when PWRHOLD pin goes low, the rising ACOKB will trigger power off. - -Optional nodes: -- clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768 - KHz outputs, so to register these as clocks with common clock framework - instantiate a sub-node named "clocks". It uses the common clock binding - documented in : - [Documentation/devicetree/bindings/clock/clock-bindings.txt] - The s2mps14 provides two (AP/BT) buffered 32.768 KHz outputs. - - #clock-cells: should be 1. - - - The following is the list of clocks generated by the controller. Each clock - is assigned an identifier and client nodes use this identifier to specify - the clock which they consume. - Clock ID Devices - ---------------------------------------------------------- - 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 - 32KhzCP 1 S2MPS11, S2MPS13, S2MPS15, S5M8767 - 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 - - - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", - "samsung,s2mps14-clk", "samsung,s5m8767-clk" - The s2msp15 uses the same compatible as s2mps13, as both provides similar clocks. - -- regulators: The regulators of s2mps11 that have to be instantiated should be -included in a sub-node named 'regulators'. Regulator nodes included in this -sub-node should be of the format as listed below. - - regulator_name { - [standard regulator constraints....]; - }; - - regulator-ramp-delay for BUCKs = [6250/12500/25000(default)/50000] uV/us - - BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explicitly - regulator-ramp-delay = <0> can be used for them to disable ramp delay. - In the absence of the regulator-ramp-delay property, the default ramp - delay will be used. - -NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set -for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. -Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6], -BUCK[3, 4], and BUCK[7, 8, 10] - -On S2MPS14 the LDO10, LDO11 and LDO12 can be configured to external control -over GPIO. To turn this feature on this property must be added to the regulator -sub-node: - - samsung,ext-control-gpios: GPIO specifier for one GPIO - controlling this regulator (enable/disable); -Example: - LDO12 { - regulator-name = "V_EMMC_2.8V"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - samsung,ext-control-gpios = <&gpk0 2 0>; - }; - - -The regulator constraints inside the regulator nodes use the standard regulator -bindings which are documented elsewhere. - -The following are the names of the regulators that the s2mps11 pmic block -supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number -as per the datasheet of s2mps11. - - - LDOn - - valid values for n are: - - S2MPS11: 1 to 38 - - S2MPS13: 1 to 40 - - S2MPS14: 1 to 25 - - S2MPS15: 1 to 27 - - S2MPU02: 1 to 28 - - Example: LDO1, LDO2, LDO28 - - BUCKn - - valid values for n are: - - S2MPS11: 1 to 10 - - S2MPS13: 1 to 10 - - S2MPS14: 1 to 5 - - S2MPS15: 1 to 10 - - S2MPU02: 1 to 7 - - Example: BUCK1, BUCK2, BUCK9 - -Example: - - s2mps11_pmic@66 { - compatible = "samsung,s2mps11-pmic"; - reg = <0x66>; - - s2m_osc: clocks { - compatible = "samsung,s2mps11-clk"; - #clock-cells = <1>; - clock-output-names = "xx", "yy", "zz"; - }; - - regulators { - ldo1_reg: LDO1 { - regulator-name = "VDD_ABB_3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - ldo2_reg: LDO2 { - regulator-name = "VDD_ALIVE_1.1V"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - buck1_reg: BUCK1 { - regulator-name = "vdd_mif"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - buck2_reg: BUCK2 { - regulator-name = "vdd_arm"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - regulator-ramp-delay = <50000>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/mfd/samsung,sec-core.txt b/Documentation/devicetree/bindings/mfd/samsung,sec-core.txt new file mode 100644 index 000000000000..cdd079bfc287 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/samsung,sec-core.txt @@ -0,0 +1,88 @@ +Binding for Samsung S2M and S5M family multi-function device +============================================================ + +This is a part of device tree bindings for S2M and S5M family multi-function +devices. + +The Samsung S2MPA01, S2MPS11/13/14/15, S2MPU02 and S5M8767 is a family +of multi-function devices which include voltage and current regulators, RTC, +charger controller, clock outputs and other sub-blocks. It is interfaced +to the host controller using an I2C interface. Each sub-block is usually +addressed by the host system using different I2C slave addresses. + + +This document describes bindings for main device node. Optional sub-blocks +must be a sub-nodes to it. Bindings for them can be found in: + - bindings/regulator/samsung,s2mpa01.txt + - bindings/regulator/samsung,s2mps11.txt + - bindings/regulator/samsung,s5m8767.txt + - bindings/clock/samsung,s2mps11.txt + + +Required properties: + - compatible: Should be one of the following + - "samsung,s2mpa01-pmic", + - "samsung,s2mps11-pmic", + - "samsung,s2mps13-pmic", + - "samsung,s2mps14-pmic", + - "samsung,s2mps15-pmic", + - "samsung,s2mpu02-pmic", + - "samsung,s5m8767-pmic". + - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. + +Optional properties: + - interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s2mps11 are delivered to. + - interrupts: Interrupt specifiers for interrupt sources. + - samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled + down. When the system is suspended it will always go down thus triggerring + unwanted buck warm reset (setting buck voltages to default values). + - samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is + connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1 + register to turn off the power. Usually the ACOKB is pulled up to VBATT so + when PWRHOLD pin goes low, the rising ACOKB will trigger power off. + +Example: + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + + s2m_osc: clocks { + compatible = "samsung,s2mps11-clk"; + #clock-cells = <1>; + clock-output-names = "xx", "yy", "zz"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <50000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/syscon.txt b/Documentation/devicetree/bindings/mfd/syscon.txt index fe8150bb3248..408f768686f1 100644 --- a/Documentation/devicetree/bindings/mfd/syscon.txt +++ b/Documentation/devicetree/bindings/mfd/syscon.txt @@ -13,6 +13,10 @@ Required properties: - compatible: Should contain "syscon". - reg: the register region can be accessed from syscon +Optional property: +- reg-io-width: the size (in bytes) of the IO accesses that should be + performed on the device. + Examples: gpr: iomuxc-gpr@020e0000 { compatible = "fsl,imx6q-iomuxc-gpr", "syscon"; diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt index 4ff7128ee3b2..c2546ced9c02 100644 --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt @@ -45,6 +45,8 @@ Required properties: - #size-cells : <0> Optional properties: +- clock : reference to the clock for the NAND controller +- clock-names : "nand" (required for the above clock) - brcm,nand-has-wp : Some versions of this IP include a write-protect (WP) control bit. It is always available on >= v7.0. Use this property to describe the rare @@ -72,6 +74,12 @@ we define additional 'compatible' properties and associated register resources w and enable registers - reg-names: (required) "nand-int-base" + * "brcm,nand-bcm6368" + - compatible: should contain "brcm,nand-bcm<soc>", "brcm,nand-bcm6368" + - reg: (required) the 'NAND_INTR_BASE' register range, with combined status + and enable registers, and boot address registers + - reg-names: (required) "nand-int-base" + * "brcm,nand-iproc" - reg: (required) the "IDM" register range, for interrupt enable and APB bus access endianness configuration, and the "EXT" register range, @@ -148,3 +156,27 @@ nand@f0442800 { }; }; }; + +nand@10000200 { + compatible = "brcm,nand-bcm63168", "brcm,nand-bcm6368", + "brcm,brcmnand-v4.0", "brcm,brcmnand"; + reg = <0x10000200 0x180>, + <0x10000600 0x200>, + <0x100000b0 0x10>; + reg-names = "nand", "nand-cache", "nand-int-base"; + interrupt-parent = <&periph_intc>; + interrupts = <50>; + clocks = <&periph_clk 20>; + clock-names = "nand"; + + #address-cells = <1>; + #size-cells = <0>; + + nand0: nandcs@0 { + compatible = "brcm,nandcs"; + reg = <0>; + nand-on-flash-bbt; + nand-ecc-strength = <1>; + nand-ecc-step-size = <512>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt index 862aa2f8837a..00c587b3d3ae 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -2,7 +2,8 @@ Required properties: - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi", - "fsl,imx7d-qspi", "fsl,imx6ul-qspi" + "fsl,imx7d-qspi", "fsl,imx6ul-qspi", + "fsl,ls1021-qspi" - reg : the first contains the register location and length, the second contains the memory mapping address and length - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory" diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt new file mode 100644 index 000000000000..29ea5853ca91 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt @@ -0,0 +1,86 @@ +* Ingenic JZ4780 NAND/BCH + +This file documents the device tree bindings for NAND flash devices on the +JZ4780. NAND devices are connected to the NEMC controller (described in +memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must +be children of the NEMC node. + +Required NAND controller device properties: +- compatible: Should be set to "ingenic,jz4780-nand". +- reg: For each bank with a NAND chip attached, should specify a bank number, + an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank). + +Optional NAND controller device properties: +- ingenic,bch-controller: To make use of the hardware BCH controller, this + property must contain a phandle for the BCH controller node. The required + properties for this node are described below. If this is not specified, + software BCH will be used instead. + +Optional children nodes: +- Individual NAND chips are children of the NAND controller node. + +Required children node properties: +- reg: An integer ranging from 1 to 6 representing the CS line to use. + +Optional children node properties: +- nand-ecc-step-size: ECC block size in bytes. +- nand-ecc-strength: ECC strength (max number of correctable bits). +- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default +- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present false +- rb-gpios: GPIO specifier for the busy pin. +- wp-gpios: GPIO specifier for the write protect pin. + +Optional child node of NAND chip nodes: +- partitions: see Documentation/devicetree/bindings/mtd/partition.txt + +Example: + +nemc: nemc@13410000 { + ... + + nandc: nand-controller@1 { + compatible = "ingenic,jz4780-nand"; + reg = <1 0 0x1000000>; /* Bank 1 */ + + #address-cells = <1>; + #size-cells = <0>; + + ingenic,bch-controller = <&bch>; + + nand@1 { + reg = <1>; + + nand-ecc-step-size = <1024>; + nand-ecc-strength = <24>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + + rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>; + + partitions { + #address-cells = <2>; + #size-cells = <2>; + ... + } + }; + }; +}; + +The BCH controller is a separate SoC component used for error correction on +NAND devices. The following is a description of the device properties for a +BCH controller. + +Required BCH properties: +- compatible: Should be set to "ingenic,jz4780-bch". +- reg: Should specify the BCH controller registers location and length. +- clocks: Clock for the BCH controller. + +Example: + +bch: bch@134d0000 { + compatible = "ingenic,jz4780-bch"; + reg = <0x134d0000 0x10000>; + + clocks = <&cgu JZ4780_CLK_BCH>; +}; diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt index 2bee68103b01..2c91c03e7eb0 100644 --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt @@ -1,15 +1,61 @@ -* MTD SPI driver for ST M25Pxx (and similar) serial flash chips +* SPI NOR flash: ST M25Pxx (and similar) serial flash chips Required properties: - #address-cells, #size-cells : Must be present if the device has sub-nodes representing partitions. - compatible : May include a device-specific string consisting of the - manufacturer and name of the chip. Bear in mind the DT binding - is not Linux-only, but in case of Linux, see the "m25p_ids" - table in drivers/mtd/devices/m25p80.c for the list of supported - chips. + manufacturer and name of the chip. A list of supported chip + names follows. Must also include "jedec,spi-nor" for any SPI NOR flash that can be identified by the JEDEC READ ID opcode (0x9F). + + Supported chip names: + at25df321a + at25df641 + at26df081a + mr25h256 + mx25l4005a + mx25l1606e + mx25l6405d + mx25l12805d + mx25l25635e + n25q064 + n25q128a11 + n25q128a13 + n25q512a + s25fl256s1 + s25fl512s + s25sl12801 + s25fl008k + s25fl064k + sst25vf040b + m25p40 + m25p80 + m25p16 + m25p32 + m25p64 + m25p128 + w25x80 + w25x32 + w25q32 + w25q32dw + w25q80bl + w25q128 + w25q256 + + The following chip names have been used historically to + designate quirky versions of flash chips that do not support the + JEDEC READ ID opcode (0x9F): + m25p05-nonjedec + m25p10-nonjedec + m25p20-nonjedec + m25p40-nonjedec + m25p80-nonjedec + m25p16-nonjedec + m25p32-nonjedec + m25p64-nonjedec + m25p128-nonjedec + - reg : Chip-Select number - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at diff --git a/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt new file mode 100644 index 000000000000..fb314f09861b --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/mtk-quadspi.txt @@ -0,0 +1,41 @@ +* Serial NOR flash controller for MTK MT81xx (and similar) + +Required properties: +- compatible: should be "mediatek,mt8173-nor"; +- reg: physical base address and length of the controller's register +- clocks: the phandle of the clocks needed by the nor controller +- clock-names: the names of the clocks + the clocks should be named "spi" and "sf". "spi" is used for spi bus, + and "sf" is used for controller, these are the clocks witch + hardware needs to enabling nor flash and nor flash controller. + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- #address-cells: should be <1> +- #size-cells: should be <0> + +The SPI flash must be a child of the nor_flash node and must have a +compatible property. Also see jedec,spi-nor.txt. + +Required properties: +- compatible: May include a device-specific string consisting of the manufacturer + and name of the chip. Must also include "jedec,spi-nor" for any + SPI NOR flash that can be identified by the JEDEC READ ID opcode (0x9F). +- reg : Chip-Select number + +Example: + +nor_flash: spi@1100d000 { + compatible = "mediatek,mt8173-nor"; + reg = <0 0x1100d000 0 0xe0>; + clocks = <&pericfg CLK_PERI_SPI>, + <&topckgen CLK_TOP_SPINFI_IFR_SEL>; + clock-names = "spi", "sf"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + }; +}; + diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt index 1c63e40659fc..81a224da63be 100644 --- a/Documentation/devicetree/bindings/mtd/partition.txt +++ b/Documentation/devicetree/bindings/mtd/partition.txt @@ -32,6 +32,8 @@ Optional properties: partition should only be mounted read-only. This is usually used for flash partitions containing early-boot firmware images or data which should not be clobbered. +- lock : Do not unlock the partition at initialization time (not supported on + all devices) Examples: diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt deleted file mode 100644 index 4451ee973223..000000000000 --- a/Documentation/devicetree/bindings/net/cdns-emac.txt +++ /dev/null @@ -1,20 +0,0 @@ -* Cadence EMAC Ethernet controller - -Required properties: -- compatible: Should be "cdns,[<chip>-]{emac}" - Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. - Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. - Or the generic form: "cdns,emac". -- reg: Address and length of the register set for the device -- interrupts: Should contain macb interrupt -- phy-mode: see ethernet.txt file in the same directory. - -Examples: - - macb0: ethernet@fffc4000 { - compatible = "cdns,at91rm9200-emac"; - reg = <0xfffc4000 0x4000>; - interrupts = <21>; - phy-mode = "rmii"; - local-mac-address = [3a 0e 03 04 05 06]; - }; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 5c397ca14cfe..d2e243b1ec0e 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -2,6 +2,7 @@ Required properties: - compatible: Should be "cdns,[<chip>-]{macb|gem}" + Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs or the 10/100Mbit IP available on sama5d3 SoCs. Use "cdns,np4-macb" for NP4 SoC devices. @@ -11,7 +12,9 @@ Required properties: Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs. Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. + Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC. + Or the generic form: "cdns,emac". - reg: Address and length of the register set for the device - interrupts: Should contain macb interrupt - phy-mode: See ethernet.txt file in the same directory. diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt index 7f81ef90146a..d87ab7c127b8 100644 --- a/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt @@ -2,6 +2,7 @@ Required properties: - compatible: should be one or more of + "brcm,bcm7425-sata-phy" "brcm,bcm7445-sata-phy" "brcm,phy-sata3" - address-cells: should be 1 diff --git a/Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt b/Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt new file mode 100644 index 000000000000..f17a56e2152f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt @@ -0,0 +1,16 @@ +Hisilicon hi6220 usb PHY +----------------------- + +Required properties: +- compatible: should be "hisilicon,hi6220-usb-phy" +- #phy-cells: must be 0 +- hisilicon,peripheral-syscon: phandle of syscon used to control phy. +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usb_phy: usbphy { + compatible = "hisilicon,hi6220-usb-phy"; + #phy-cells = <0>; + phy-supply = <&fixed_5v_hub>; + hisilicon,peripheral-syscon = <&sys_ctrl>; + }; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt new file mode 100644 index 000000000000..2390e4e9c84c --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -0,0 +1,39 @@ +* Renesas R-Car generation 3 USB 2.0 PHY + +This file provides information on what the device node for the R-Car generation +3 USB 2.0 PHY contains. + +Required properties: +- compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 + SoC. +- reg: offset and length of the partial USB 2.0 Host register block. +- reg-names: must be "usb2_host". +- clocks: clock phandle and specifier pair(s). +- #phy-cells: see phy-bindings.txt in the same directory, must be <0>. + +Optional properties: +To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are +combined, the device tree node should set HSUSB properties to reg and reg-names +properties. This is because HSUSB has registers to select USB 2.0 host or +peripheral at that channel: +- reg: offset and length of the partial HSUSB register block. +- reg-names: must be "hsusb". +- interrupts: interrupt specifier for the PHY. + +Example (R-Car H3): + + usb-phy@ee080200 { + compatible = "renesas,usb2-phy-r8a7795"; + reg = <0 0xee080200 0 0x700>, <0 0xe6590100 0 0x100>; + reg-names = "usb2_host", "hsusb"; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7795_CLK_EHCI0>, + <&mstp7_clks R8A7795_CLK_HSUSB>; + }; + + usb-phy@ee0a0200 { + compatible = "renesas,usb2-phy-r8a7795"; + reg = <0 0xee0a0200 0 0x700>; + reg-names = "usb2_host"; + clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt index 826454ac43bb..68498d560354 100644 --- a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt @@ -1,7 +1,10 @@ ROCKCHIP USB2 PHY Required properties: - - compatible: rockchip,rk3288-usb-phy + - compatible: matching the soc type, one of + "rockchip,rk3066a-usb-phy" + "rockchip,rk3188-usb-phy" + "rockchip,rk3288-usb-phy" - rockchip,grf : phandle to the syscon managing the "general register files" - #address-cells: should be 1 @@ -21,6 +24,7 @@ required properties: Optional Properties: - clocks : phandle + clock specifier for the phy clocks - clock-names: string, clock name, must be "phyclk" +- #clock-cells: for users of the phy-pll, should be 0 Example: diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index 0cebf7454517..95736d77fbb7 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -9,6 +9,7 @@ Required properties: * allwinner,sun7i-a20-usb-phy * allwinner,sun8i-a23-usb-phy * allwinner,sun8i-a33-usb-phy + * allwinner,sun8i-h3-usb-phy - reg : a list of offset + length pairs - reg-names : * "phy_ctrl" diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index 9cf9446eaf2e..a3b394587874 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -31,6 +31,8 @@ OMAP USB2 PHY Required properties: - compatible: Should be "ti,omap-usb2" + Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY + in DRA7x - reg : Address and length of the register set for the device. - #phy-cells: determine the number of cells that should be given in the phandle while referencing this phy. @@ -40,10 +42,14 @@ Required properties: * "wkupclk" - wakeup clock. * "refclk" - reference clock (optional). -Optional properties: +Deprecated properties: - ctrl-module : phandle of the control module used by PHY driver to power on the PHY. +Recommended properies: +- syscon-phy-power : phandle/offset pair. Phandle to the system control + module and the register offset to power on/off the PHY. + This is usually a subnode of ocp2scp to which it is connected. usb2phy@4a0ad080 { @@ -77,14 +83,22 @@ Required properties: * "div-clk" - apll clock Optional properties: - - ctrl-module : phandle of the control module used by PHY driver to power on - the PHY. - id: If there are multiple instance of the same type, in order to differentiate between each instance "id" can be used (e.g., multi-lane PCIe PHY). If "id" is not provided, it is set to default value of '1'. - syscon-pllreset: Handle to system control region that contains the CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0 register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy. + - syscon-pcs : phandle/offset pair. Phandle to the system control module and the + register offset to write the PCS delay value. + +Deprecated properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +Recommended properies: + - syscon-phy-power : phandle/offset pair. Phandle to the system control + module and the register offset to power on/off the PHY. This is usually a subnode of ocp2scp to which it is connected. diff --git a/Documentation/devicetree/bindings/regulator/lm363x-regulator.txt b/Documentation/devicetree/bindings/regulator/lm363x-regulator.txt new file mode 100644 index 000000000000..8f14df9d1205 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/lm363x-regulator.txt @@ -0,0 +1,34 @@ +TI LMU LM363x regulator device tree bindings + +LM363x regulator driver supports LM3631 and LM3632. +LM3631 has five regulators and LM3632 supports three regulators. + +Required property: + - compatible: "ti,lm363x-regulator" + +Optional properties: + LM3632 has external enable pins for two LDOs. + - ti,lcm-en1-gpio: A GPIO specifier for Vpos control pin. + - ti,lcm-en2-gpio: A GPIO specifier for Vneg control pin. + +Child nodes: + LM3631 + - vboost + - vcont + - voref + - vpos + - vneg + + LM3632 + - vboost + - vpos + - vneg + + Optional properties of a child node: + Each sub-node should contain the constraints and initialization. + Please refer to [1]. + +Examples: Please refer to ti-lmu dt-bindings [2]. + +[1] ../regulator/regulator.txt +[2] ../mfd/ti-lmu.txt diff --git a/Documentation/devicetree/bindings/regulator/pv88060.txt b/Documentation/devicetree/bindings/regulator/pv88060.txt new file mode 100644 index 000000000000..10a6dadc008e --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pv88060.txt @@ -0,0 +1,124 @@ +* Powerventure Semiconductor PV88060 Voltage Regulator + +Required properties: +- compatible: "pvs,pv88060". +- reg: I2C slave address, usually 0x49. +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4, + SW5, and SW6. + +Optional properties: +- Any optional property defined in regulator.txt + +Example + + pmic: pv88060@49 { + compatible = "pvs,pv88060"; + reg = <0x49>; + interrupt-parent = <&gpio>; + interrupts = <24 24>; + + regulators { + BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <4387500>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + regulator-boot-on; + }; + + LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + LDO7 { + regulator-name = "ldo7"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3350000>; + regulator-boot-on; + }; + + SW1 { + regulator-name = "sw1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + SW2 { + regulator-name = "sw2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + SW3 { + regulator-name = "sw3"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + SW4 { + regulator-name = "sw4"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + SW5 { + regulator-name = "sw5"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + + SW6 { + regulator-name = "sw6"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + }; + };
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/regulator/pv88090.txt b/Documentation/devicetree/bindings/regulator/pv88090.txt new file mode 100644 index 000000000000..e52b2a95cdde --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pv88090.txt @@ -0,0 +1,65 @@ +* Powerventure Semiconductor PV88090 Voltage Regulator + +Required properties: +- compatible: "pvs,pv88090". +- reg: I2C slave address, usually 0x48. +- interrupts: the interrupt outputs of the controller +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name, with valid + values listed below. The content of each sub-node is defined by the + standard binding for regulators; see regulator.txt. + BUCK1, BUCK2, BUCK3, LDO1, and LDO2. + +Optional properties: +- Any optional property defined in regulator.txt + +Example + + pmic: pv88090@48 { + compatible = "pvs,pv88090"; + reg = <0x48>; + interrupt-parent = <&gpio>; + interrupts = <24 24>; + + regulators { + BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = < 220000>; + regulator-max-microamp = <7040000>; + regulator-boot-on; + }; + + BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + }; + + BUCK3 { + regulator-name = "buck3"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1393750>; + regulator-min-microamp = <1496000>; + regulator-max-microamp = <4189000>; + regulator-boot-on; + }; + + LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <4350000>; + regulator-boot-on; + }; + + LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = < 650000>; + regulator-max-microvolt = <2225000>; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom,smd-rpm.txt b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt index e27f5c4c54fd..1f8d6f84b657 100644 --- a/Documentation/devicetree/bindings/soc/qcom,smd-rpm.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt @@ -1,27 +1,17 @@ -Qualcomm Resource Power Manager (RPM) over SMD +QCOM SMD RPM REGULATOR -This driver is used to interface with the Resource Power Manager (RPM) found in -various Qualcomm platforms. The RPM allows each component in the system to vote -for state of the system resources, such as clocks, regulators and bus -frequencies. +The Qualcomm RPM over SMD regulator is modelled as a subdevice of the RPM. +Because SMD is used as the communication transport mechanism, the RPM resides as +a subnode of the SMD. As such, the SMD-RPM regulator requires that the SMD and +RPM nodes be present. -- compatible: - Usage: required - Value type: <string> - Definition: must be one of: - "qcom,rpm-msm8974" +Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt for +information pertaining to the SMD node. -- qcom,smd-channels: - Usage: required - Value type: <stringlist> - Definition: Shared Memory channel used for communication with the RPM +Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt for +information regarding the RPM node. -= SUBDEVICES - -The RPM exposes resources to its subnodes. The below bindings specify the set -of valid subnodes that can operate on these resources. - -== Regulators +== Regulator Regulator nodes are identified by their compatible: @@ -30,7 +20,9 @@ Regulator nodes are identified by their compatible: Value type: <string> Definition: must be one of: "qcom,rpm-pm8841-regulators" + "qcom,rpm-pm8916-regulators" "qcom,rpm-pm8941-regulators" + "qcom,rpm-pma8084-regulators" - vdd_s1-supply: - vdd_s2-supply: @@ -48,6 +40,19 @@ Regulator nodes are identified by their compatible: - vdd_s1-supply: - vdd_s2-supply: - vdd_s3-supply: +- vdd_s4-supply: +- vdd_l1_l2_l3-supply: +- vdd_l4_l5_l6-supply: +- vdd_l7-supply: +- vdd_l8_l9_l10_l11_l12_l13_l14_l15_l16_l17_l18-supply: + Usage: optional (pm8916 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: - vdd_l1_l3-supply: - vdd_l2_lvs1_2_3-supply: - vdd_l4_l11-supply: @@ -63,6 +68,35 @@ Regulator nodes are identified by their compatible: Definition: reference to regulator supplying the input pin, as described in the data sheet +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_s7-supply: +- vdd_s8-supply: +- vdd_s9-supply: +- vdd_s10-supply: +- vdd_s11-supply: +- vdd_s12-supply: +- vdd_l1_l11-supply: +- vdd_l2_l3_l4_l27-supply: +- vdd_l5_l7-supply: +- vdd_l6_l12_l14_l15_l26-supply: +- vdd_l8-supply: +- vdd_l9_l10_l13_l20_l23_l24-supply: +- vdd_l16_l25-supply: +- vdd_l17-supply: +- vdd_l18-supply: +- vdd_l19-supply: +- vdd_l21-supply: +- vdd_l22-supply: + Usage: optional (pma8084 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the pmics below. @@ -70,11 +104,20 @@ of the pmics below. pm8841: s1, s2, s3, s4, s5, s6, s7, s8 +pm8916: + s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, + l14, l15, l16, l17, l18 + pm8941: s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3, 5vs1, 5vs2 +pma8084: + s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5, + l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20, + l21, l22, l23, l24, l25, l26, l27, lvs1, lvs2, lvs3, lvs4, 5vs1 + The content of each sub-node is defined by the standard binding for regulators - see regulator.txt. @@ -114,4 +157,3 @@ see regulator.txt. }; }; }; - diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt deleted file mode 100644 index 20191315e444..000000000000 --- a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt +++ /dev/null @@ -1,163 +0,0 @@ -* Samsung S5M8767 Voltage and Current Regulator - -The Samsung S5M8767 is a multi-function device which includes voltage and -current regulators, rtc, charger controller and other sub-blocks. It is -interfaced to the host controller using a i2c interface. Each sub-block is -addressed by the host system using different i2c slave address. This document -describes the bindings for 'pmic' sub-block of s5m8767. - -Required properties: -- compatible: Should be "samsung,s5m8767-pmic". -- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. - -- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) - units for buck2 when changing voltage using gpio dvs. Refer to [1] below - for additional information. - -- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV) - units for buck3 when changing voltage using gpio dvs. Refer to [1] below - for additional information. - -- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV) - units for buck4 when changing voltage using gpio dvs. Refer to [1] below - for additional information. - -- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used - for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. - -[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' - property should specify atleast one voltage level (which would be a - safe operating voltage). - - If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional - property is specified, then all the eight voltage values for the - 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. - -Optional properties: -- interrupt-parent: Specifies the phandle of the interrupt controller to which - the interrupts from s5m8767 are delivered to. -- interrupts: Interrupt specifiers for two interrupt sources. - - First interrupt specifier is for 'irq1' interrupt. - - Second interrupt specifier is for 'alert' interrupt. -- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. -- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. -- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. - -Additional properties required if either of the optional properties are used: - -- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from - the possible 8 options selectable by the dvs gpios. The value of this - property should be between 0 and 7. If not specified or if out of range, the - default value of this property is set to 0. - -- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used - for dvs. The format of the gpio specifier depends in the gpio controller. - -Regulators: The regulators of s5m8767 that have to be instantiated should be -included in a sub-node named 'regulators'. Regulator nodes included in this -sub-node should be of the format as listed below. - - regulator_name { - ldo1_reg: LDO1 { - regulator-name = "VDD_ALIVE_1.0V"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - regulator-boot-on; - op_mode = <1>; /* Normal Mode */ - }; - }; -The above regulator entries are defined in regulator bindings documentation -except these properties: - - op_mode: describes the different operating modes of the LDO's with - power mode change in SOC. The different possible values are, - 0 - always off mode - 1 - on in normal mode - 2 - low power mode - 3 - suspend mode - - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one - GPIO controlling this regulator (enable/disable); This is - valid only for buck9. - -The following are the names of the regulators that the s5m8767 pmic block -supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number -as per the datasheet of s5m8767. - - - LDOn - - valid values for n are 1 to 28 - - Example: LDO1, LDO2, LDO28 - - BUCKn - - valid values for n are 1 to 9. - - Example: BUCK1, BUCK2, BUCK9 - -The bindings inside the regulator nodes use the standard regulator bindings -which are documented elsewhere. - -Example: - - s5m8767_pmic@66 { - compatible = "samsung,s5m8767-pmic"; - reg = <0x66>; - - s5m8767,pmic-buck2-uses-gpio-dvs; - s5m8767,pmic-buck3-uses-gpio-dvs; - s5m8767,pmic-buck4-uses-gpio-dvs; - - s5m8767,pmic-buck-default-dvs-idx = <0>; - - s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */ - <&gpx0 1 0>, /* DVS2 */ - <&gpx0 2 0>; /* DVS3 */ - - s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */ - <&gpx2 4 0>, /* SET2 */ - <&gpx2 5 0>; /* SET3 */ - - s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, - <1250000>, <1200000>, - <1150000>, <1100000>, - <1000000>, <950000>; - - s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, - <1100000>, <1100000>, - <1000000>, <1000000>, - <1000000>, <1000000>; - - s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>; - - regulators { - ldo1_reg: LDO1 { - regulator-name = "VDD_ABB_3.3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - op_mode = <1>; /* Normal Mode */ - }; - - ldo2_reg: LDO2 { - regulator-name = "VDD_ALIVE_1.1V"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - buck1_reg: BUCK1 { - regulator-name = "VDD_MIF_1.2V"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - regulator-boot-on; - }; - - vemmc_reg: BUCK9 { - regulator-name = "VMEM_VDD_2.8V"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - op_mode = <3>; /* Standby Mode */ - s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/regulator/samsung,s2mpa01.txt b/Documentation/devicetree/bindings/regulator/samsung,s2mpa01.txt new file mode 100644 index 000000000000..bae3c7f838cf --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/samsung,s2mpa01.txt @@ -0,0 +1,79 @@ +Binding for Samsung S2MPA01 regulator block +=========================================== + +This is a part of device tree bindings for S2M family multi-function devices. +More information can be found in bindings/mfd/sec-core.txt file. + +The S2MPA01 device provide buck and LDO regulators. + +To register these with regulator framework instantiate under main device node +a sub-node named "regulators" with more sub-nodes for each regulator using the +common regulator binding documented in: + - Documentation/devicetree/bindings/regulator/regulator.txt + + +Names of regulators supported by S2MPA01 device: + - LDOn + - valid values for n are 1 to 26 + - Example: LDO1, LD02, LDO26 + - BUCKn + - valid values for n are 1 to 10. + - Example: BUCK1, BUCK2, BUCK9 +Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of device. + + +Optional properties of buck regulator nodes under "regulators" sub-node: + - regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500 + (default), 25000, or 50000. May be 0 for disabling the ramp delay on + BUCK{1,2,3,4}. + + In the absence of the regulator-ramp-delay property, the default ramp + delay will be used. + + Note: Some bucks share the ramp rate setting i.e. same ramp value + will be set for a particular group of bucks so provide the same + regulator-ramp-delay value for them. + Groups sharing ramp rate: + - buck{1,6}, + - buck{2,4}, + - buck{8,9,10}. + +Example: + + s2mpa01_pmic@66 { + compatible = "samsung,s2mpa01-pmic"; + reg = <0x66>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDDQ_MMC2"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <50000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/samsung,s2mps11.txt b/Documentation/devicetree/bindings/regulator/samsung,s2mps11.txt new file mode 100644 index 000000000000..27a48bf1b185 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/samsung,s2mps11.txt @@ -0,0 +1,102 @@ +Binding for Samsung S2M family regulator block +============================================== + +This is a part of device tree bindings for S2M family multi-function devices. +More information can be found in bindings/mfd/sec-core.txt file. + +The S2MPS11/13/14/15 and S2MPU02 devices provide buck and LDO regulators. + +To register these with regulator framework instantiate under main device node +a sub-node named "regulators" with more sub-nodes for each regulator using the +common regulator binding documented in: + - Documentation/devicetree/bindings/regulator/regulator.txt + + +Names of regulators supported by different devices: + - LDOn + - valid values for n are: + - S2MPS11: 1 to 38 + - S2MPS13: 1 to 40 + - S2MPS14: 1 to 25 + - S2MPS15: 1 to 27 + - S2MPU02: 1 to 28 + - Example: LDO1, LDO2, LDO28 + - BUCKn + - valid values for n are: + - S2MPS11: 1 to 10 + - S2MPS13: 1 to 10 + - S2MPS14: 1 to 5 + - S2MPS15: 1 to 10 + - S2MPU02: 1 to 7 + - Example: BUCK1, BUCK2, BUCK9 +Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of device. + + +Optional properties of the nodes under "regulators" sub-node: + - regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500, + 25000 (default) or 50000. + + Additionally S2MPS11 supports disabling ramp delay for BUCK{2,3,4,6} + by setting it to <0>. + + Note: On S2MPS11 some bucks share the ramp rate setting i.e. same ramp value + will be set for a particular group of bucks so provide the same + regulator-ramp-delay value for them. + Groups sharing ramp rate: + - buck{1,6}, + - buck{3,4}, + - buck{7,8,10}. + + - samsung,ext-control-gpios: On S2MPS14 the LDO10, LDO11 and LDO12 can be + configured to external control over GPIO. To turn this feature on this + property must be added to the regulator sub-node: + - samsung,ext-control-gpios: GPIO specifier for one GPIO + controlling this regulator (enable/disable) + Example: + LDO12 { + regulator-name = "V_EMMC_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + +Example: + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <50000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt new file mode 100644 index 000000000000..093edda0c8df --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt @@ -0,0 +1,145 @@ +Binding for Samsung S5M8767 regulator block +=========================================== + +This is a part of device tree bindings for S5M family multi-function devices. +More information can be found in bindings/mfd/sec-core.txt file. + +The S5M8767 device provide buck and LDO regulators. + +To register these with regulator framework instantiate under main device node +a sub-node named "regulators" with more sub-nodes for each regulator using the +common regulator binding documented in: + - Documentation/devicetree/bindings/regulator/regulator.txt + + +Required properties of the main device node (the parent!): + - s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + + - s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck3 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + + - s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck4 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + + - s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used + for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. + + [1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. + +Optional properties of the main device node (the parent!): + - s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. + - s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. + - s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: + + - s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + + - s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + + +Names of regulators supported by S5M8767 device: + - LDOn + - valid values for n are 1 to 28 + - Example: LDO1, LDO2, LDO28 + - BUCKn + - valid values for n are 1 to 9. + - Example: BUCK1, BUCK2, BUCK9 +Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of device. + + +Optional properties of the nodes under "regulators" sub-node: + - op_mode: describes the different operating modes of the LDO's with + power mode change in SOC. The different possible values are, + 0 - always off mode + 1 - on in normal mode + 2 - low power mode + 3 - suspend mode + - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one + GPIO controlling this regulator + (enable/disable); This is valid only + for buck9. + +Example: + + s5m8767_pmic@66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + + s5m8767,pmic-buck2-uses-gpio-dvs; + s5m8767,pmic-buck3-uses-gpio-dvs; + s5m8767,pmic-buck4-uses-gpio-dvs; + + s5m8767,pmic-buck-default-dvs-idx = <0>; + + s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */ + <&gpx0 1 0>, /* DVS2 */ + <&gpx0 2 0>; /* DVS3 */ + + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */ + <&gpx2 4 0>, /* SET2 */ + <&gpx2 5 0>; /* SET3 */ + + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + vemmc_reg: BUCK9 { + regulator-name = "VMEM_VDD_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + op_mode = <3>; /* Standby Mode */ + s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt new file mode 100644 index 000000000000..f67e761bcc18 --- /dev/null +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt @@ -0,0 +1,69 @@ +* HiSilicon SAS controller + +The HiSilicon SAS controller supports SAS/SATA. + +Main node required properties: + - compatible : value should be as follows: + (a) "hisilicon,hip05-sas-v1" for v1 hw in hip05 chipset + - sas-addr : array of 8 bytes for host SAS address + - reg : Address and length of the SAS register + - hisilicon,sas-syscon: phandle of syscon used for sas control + - ctrl-reset-reg : offset to controller reset register in ctrl reg + - ctrl-reset-sts-reg : offset to controller reset status register in ctrl reg + - ctrl-clock-ena-reg : offset to controller clock enable register in ctrl reg + - queue-count : number of delivery and completion queues in the controller + - phy-count : number of phys accessible by the controller + - interrupts : Interrupts for phys, completion queues, and fatal + sources; the interrupts are ordered in 3 groups, as follows: + - Phy interrupts + - Completion queue interrupts + - Fatal interrupts + Phy interrupts : Each phy has 3 interrupt sources: + - broadcast + - phyup + - abnormal + The phy interrupts are ordered into groups of 3 per phy + (broadcast, phyup, and abnormal) in increasing order. + Completion queue interrupts : each completion queue has 1 + interrupt source. + The interrupts are ordered in increasing order. + Fatal interrupts : the fatal interrupts are ordered as follows: + - ECC + - AXI bus + +Example: + sas0: sas@c1000000 { + compatible = "hisilicon,hip05-sas-v1"; + sas-addr = [50 01 88 20 16 00 00 0a]; + reg = <0x0 0xc1000000 0x0 0x10000>; + hisilicon,sas-syscon = <&pcie_sas>; + ctrl-reset-reg = <0xa60>; + ctrl-reset-sts-reg = <0x5a30>; + ctrl-clock-ena-reg = <0x338>; + queue-count = <32>; + phy-count = <8>; + dma-coherent; + interrupt-parent = <&mbigen_dsa>; + interrupts = <259 4>,<263 4>,<264 4>,/* phy0 */ + <269 4>,<273 4>,<274 4>,/* phy1 */ + <279 4>,<283 4>,<284 4>,/* phy2 */ + <289 4>,<293 4>,<294 4>,/* phy3 */ + <299 4>,<303 4>,<304 4>,/* phy4 */ + <309 4>,<313 4>,<314 4>,/* phy5 */ + <319 4>,<323 4>,<324 4>,/* phy6 */ + <329 4>,<333 4>,<334 4>,/* phy7 */ + <336 1>,<337 1>,<338 1>,/* cq0-2 */ + <339 1>,<340 1>,<341 1>,/* cq3-5 */ + <342 1>,<343 1>,<344 1>,/* cq6-8 */ + <345 1>,<346 1>,<347 1>,/* cq9-11 */ + <348 1>,<349 1>,<350 1>,/* cq12-14 */ + <351 1>,<352 1>,<353 1>,/* cq15-17 */ + <354 1>,<355 1>,<356 1>,/* cq18-20 */ + <357 1>,<358 1>,<359 1>,/* cq21-23 */ + <360 1>,<361 1>,<362 1>,/* cq24-26 */ + <363 1>,<364 1>,<365 1>,/* cq27-29 */ + <366 1>,<367 1>/* cq30-31 */ + <376 4>,/* fatal ecc */ + <381 4>;/* fatal axi */ + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 91d5ab0e60fc..936ab5b87324 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -14,7 +14,6 @@ Required properties: tegra132, or tegra210. - "nxp,lpc3220-uart" - "ralink,rt2880-uart" - - "ibm,qpace-nwp-serial" - "altr,16550-FIFO32" - "altr,16550-FIFO64" - "altr,16550-FIFO128" diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 73f825e5e644..401b1b33c2c4 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -2,7 +2,7 @@ Required properties: - - compatible: Must contain one of the following: + - compatible: Must contain one or more of the following: - "renesas,scif-r7s72100" for R7S72100 (RZ/A1H) SCIF compatible UART. - "renesas,scifa-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFA compatible UART. @@ -15,10 +15,14 @@ Required properties: - "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART. - "renesas,scifb-r8a7790" for R8A7790 (R-Car H2) SCIFB compatible UART. - "renesas,hscif-r8a7790" for R8A7790 (R-Car H2) HSCIF compatible UART. - - "renesas,scif-r8a7791" for R8A7791 (R-Car M2) SCIF compatible UART. - - "renesas,scifa-r8a7791" for R8A7791 (R-Car M2) SCIFA compatible UART. - - "renesas,scifb-r8a7791" for R8A7791 (R-Car M2) SCIFB compatible UART. - - "renesas,hscif-r8a7791" for R8A7791 (R-Car M2) HSCIF compatible UART. + - "renesas,scif-r8a7791" for R8A7791 (R-Car M2-W) SCIF compatible UART. + - "renesas,scifa-r8a7791" for R8A7791 (R-Car M2-W) SCIFA compatible UART. + - "renesas,scifb-r8a7791" for R8A7791 (R-Car M2-W) SCIFB compatible UART. + - "renesas,hscif-r8a7791" for R8A7791 (R-Car M2-W) HSCIF compatible UART. + - "renesas,scif-r8a7793" for R8A7793 (R-Car M2-N) SCIF compatible UART. + - "renesas,scifa-r8a7793" for R8A7793 (R-Car M2-N) SCIFA compatible UART. + - "renesas,scifb-r8a7793" for R8A7793 (R-Car M2-N) SCIFB compatible UART. + - "renesas,hscif-r8a7793" for R8A7793 (R-Car M2-N) HSCIF compatible UART. - "renesas,scif-r8a7794" for R8A7794 (R-Car E2) SCIF compatible UART. - "renesas,scifa-r8a7794" for R8A7794 (R-Car E2) SCIFA compatible UART. - "renesas,scifb-r8a7794" for R8A7794 (R-Car E2) SCIFB compatible UART. @@ -27,6 +31,14 @@ Required properties: - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. + - "renesas,rcar-gen1-scif" for R-Car Gen1 SCIF compatible UART, + - "renesas,rcar-gen2-scif" for R-Car Gen2 SCIF compatible UART, + - "renesas,rcar-gen3-scif" for R-Car Gen3 SCIF compatible UART, + - "renesas,rcar-gen2-scifa" for R-Car Gen2 SCIFA compatible UART, + - "renesas,rcar-gen2-scifb" for R-Car Gen2 SCIFB compatible UART, + - "renesas,rcar-gen1-hscif" for R-Car Gen1 HSCIF compatible UART, + - "renesas,rcar-gen2-hscif" for R-Car Gen2 HSCIF compatible UART, + - "renesas,rcar-gen3-hscif" for R-Car Gen3 HSCIF compatible UART, - "renesas,scif" for generic SCIF compatible UART. - "renesas,scifa" for generic SCIFA compatible UART. - "renesas,scifb" for generic SCIFB compatible UART. @@ -34,15 +46,26 @@ Required properties: - "renesas,sci" for generic SCI compatible UART. When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first followed by the - generic version. + SoC-specific version corresponding to the platform first, followed by the + family-specific and/or generic versions. - reg: Base address and length of the I/O registers used by the UART. - interrupts: Must contain an interrupt-specifier for the SCIx interrupt. - clocks: Must contain a phandle and clock-specifier pair for each entry in clock-names. - - clock-names: Must contain "sci_ick" for the SCIx UART interface clock. + - clock-names: Must contain "fck" for the SCIx UART functional clock. + Apart from the divided functional clock, there may be other possible + sources for the sampling clock, depending on SCIx variant. + On (H)SCI(F) and some SCIFA, an additional clock may be specified: + - "hsck" for the optional external clock input (on HSCIF), + - "sck" for the optional external clock input (on other variants). + On UARTs equipped with a Baud Rate Generator for External Clock (BRG) + (some SCIF and HSCIF), additional clocks may be specified: + - "brg_int" for the optional internal clock source for the frequency + divider (typically the (AXI or SHwy) bus clock), + - "scif_clk" for the optional external clock source for the frequency + divider (SCIF_CLK). Note: Each enabled SCIx UART should have an alias correctly numbered in the "aliases" node. @@ -58,12 +81,13 @@ Example: }; scifa0: serial@e6c40000 { - compatible = "renesas,scifa-r8a7790", "renesas,scifa"; + compatible = "renesas,scifa-r8a7790", + "renesas,rcar-gen2-scifa", "renesas,scifa"; reg = <0 0xe6c40000 0 64>; interrupt-parent = <&gic>; interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp2_clks R8A7790_CLK_SCIFA0>; - clock-names = "sci_ick"; + clock-names = "fck"; dmas = <&dmac0 0x21>, <&dmac0 0x22>; dma-names = "tx", "rx"; }; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt new file mode 100644 index 000000000000..a48049ccf6d0 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.txt @@ -0,0 +1,58 @@ +Qualcomm Resource Power Manager (RPM) over SMD + +This driver is used to interface with the Resource Power Manager (RPM) found in +various Qualcomm platforms. The RPM allows each component in the system to vote +for state of the system resources, such as clocks, regulators and bus +frequencies. + +The SMD information for the RPM edge should be filled out. See qcom,smd.txt for +the required edge properties. All SMD related properties will reside within the +RPM node itself. + += SUBDEVICES + +The RPM exposes resources to its subnodes. The rpm_requests node must be +present and this subnode may contain children that designate regulator +resources. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,rpm-apq8084" + "qcom,rpm-msm8916" + "qcom,rpm-msm8974" + +- qcom,smd-channels: + Usage: required + Value type: <string> + Definition: must be "rpm_requests" + +Refer to Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.txt +for information on the regulator subnodes that can exist under the rpm_requests. + +Example: + + soc { + apcs: syscon@f9011000 { + compatible = "syscon"; + reg = <0xf9011000 0x1000>; + }; + }; + + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-msm8974"; + qcom,smd-channels = "rpm_requests"; + + ... + }; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/atmel-classd.txt b/Documentation/devicetree/bindings/sound/atmel-classd.txt index 0018451c4351..549e701cb7a1 100644 --- a/Documentation/devicetree/bindings/sound/atmel-classd.txt +++ b/Documentation/devicetree/bindings/sound/atmel-classd.txt @@ -16,6 +16,10 @@ Required properties: Required elements: "pclk", "gclk" and "aclk". - clocks Please refer to clock-bindings.txt. +- assigned-clocks + Should be <&classd_gclk>. +- assigned-clock-parents + Should be <&audio_pll_pmc>. Optional properties: - pinctrl-names, pinctrl-0 @@ -43,6 +47,8 @@ classd: classd@fc048000 { dma-names = "tx"; clocks = <&classd_clk>, <&classd_gclk>, <&audio_pll_pmc>; clock-names = "pclk", "gclk", "aclk"; + assigned-clocks = <&classd_gclk>; + assigned-clock-parents = <&audio_pll_pmc>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_classd_default>; diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt index e045e90a0924..68c4e8d96bed 100644 --- a/Documentation/devicetree/bindings/sound/wm8994.txt +++ b/Documentation/devicetree/bindings/sound/wm8994.txt @@ -30,7 +30,7 @@ Optional properties: - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. The first cell is the IRQ number. The second cell is the flags, encoded as the trigger masks from - Documentation/devicetree/bindings/interrupts.txt + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt - clocks : A list of up to two phandle and clock specifier pairs - clock-names : A list of clock names sorted in the same order as clocks. diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 705075da2f10..aa005c1d10d9 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -10,6 +10,7 @@ Required properties: "renesas,msiof-r8a7792" (R-Car V2H) "renesas,msiof-r8a7793" (R-Car M2-N) "renesas,msiof-r8a7794" (R-Car E2) + "renesas,msiof-sh73a0" (SH-Mobile AG5) - reg : A list of offsets and lengths of the register sets for the device. If only one register set is present, it is to be used diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index ce363c923f44..e43f4cf4cf35 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -2,9 +2,10 @@ Binding for MTK SPI controller Required properties: - compatible: should be one of the following. - - mediatek,mt8173-spi: for mt8173 platforms - - mediatek,mt8135-spi: for mt8135 platforms + - mediatek,mt2701-spi: for mt2701 platforms - mediatek,mt6589-spi: for mt6589 platforms + - mediatek,mt8135-spi: for mt8135 platforms + - mediatek,mt8173-spi: for mt8173 platforms - #address-cells: should be 1. @@ -29,10 +30,10 @@ Required properties: muxes clock, and "spi-clk" for the clock gate. Optional properties: --cs-gpios: see spi-bus.txt, only required for MT8173. +-cs-gpios: see spi-bus.txt. - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi - controller used. This is a array, the element value should be 0~3, + controller used. This is an array, the element value should be 0~3, only required for MT8173. 0: specify GPIO69,70,71,72 for spi pins. 1: specify GPIO102,103,104,105 for spi pins. diff --git a/Documentation/devicetree/bindings/arm/rockchip/pmu-sram.txt b/Documentation/devicetree/bindings/sram/rockchip-pmu-sram.txt index 6b42fda306ff..6b42fda306ff 100644 --- a/Documentation/devicetree/bindings/arm/rockchip/pmu-sram.txt +++ b/Documentation/devicetree/bindings/sram/rockchip-pmu-sram.txt diff --git a/Documentation/devicetree/bindings/arm/rockchip/smp-sram.txt b/Documentation/devicetree/bindings/sram/rockchip-smp-sram.txt index d9416fb8db6f..800701ecffca 100644 --- a/Documentation/devicetree/bindings/arm/rockchip/smp-sram.txt +++ b/Documentation/devicetree/bindings/sram/rockchip-smp-sram.txt @@ -12,7 +12,7 @@ Required sub-node properties: - compatible : should be "rockchip,rk3066-smp-sram" The rest of the properties should follow the generic mmio-sram discription -found in ../../misc/sram.txt +found in Documentation/devicetree/bindings/sram/sram.txt Example: diff --git a/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt b/Documentation/devicetree/bindings/sram/samsung-sram.txt index 4a0a4f70a0ce..6bc474b2b885 100644 --- a/Documentation/devicetree/bindings/arm/exynos/smp-sysram.txt +++ b/Documentation/devicetree/bindings/sram/samsung-sram.txt @@ -15,7 +15,7 @@ Required sub-node properties: "samsung,exynos4210-sysram-ns" : for Non-secure SYSRAM The rest of the properties should follow the generic mmio-sram discription -found in ../../misc/sysram.txt +found in Documentation/devicetree/bindings/sram/sram.txt Example: diff --git a/Documentation/devicetree/bindings/misc/sram.txt b/Documentation/devicetree/bindings/sram/sram.txt index 42ee9438b771..42ee9438b771 100644 --- a/Documentation/devicetree/bindings/misc/sram.txt +++ b/Documentation/devicetree/bindings/sram/sram.txt diff --git a/Documentation/devicetree/bindings/soc/sunxi/sram.txt b/Documentation/devicetree/bindings/sram/sunxi-sram.txt index 067698112f5f..8d5665468fe7 100644 --- a/Documentation/devicetree/bindings/soc/sunxi/sram.txt +++ b/Documentation/devicetree/bindings/sram/sunxi-sram.txt @@ -16,7 +16,7 @@ SRAM nodes ---------- Each SRAM is described using the mmio-sram bindings documented in -Documentation/devicetree/bindings/misc/sram.txt +Documentation/devicetree/bindings/sram/sram.txt Each SRAM will have SRAM sections that are going to be handled by the SRAM controller as subnodes. These sections are represented following diff --git a/Documentation/devicetree/bindings/staging/ion/hi6220-ion.txt b/Documentation/devicetree/bindings/staging/ion/hi6220-ion.txt new file mode 100644 index 000000000000..c59e27c632c1 --- /dev/null +++ b/Documentation/devicetree/bindings/staging/ion/hi6220-ion.txt @@ -0,0 +1,31 @@ +Hi6220 SoC ION +=================================================================== +Required properties: +- compatible : "hisilicon,hi6220-ion" +- list of the ION heaps + - heap name : maybe heap_sys_user@0 + - heap id : id should be unique in the system. + - heap base : base ddr address of the heap,0 means that + it is dynamic. + - heap size : memory size and 0 means it is dynamic. + - heap type : the heap type of the heap, please also + see the define in ion.h(drivers/staging/android/uapi/ion.h) +------------------------------------------------------------------- +Example: + hi6220-ion { + compatible = "hisilicon,hi6220-ion"; + heap_sys_user@0 { + heap-name = "sys_user"; + heap-id = <0x0>; + heap-base = <0x0>; + heap-size = <0x0>; + heap-type = "ion_system"; + }; + heap_sys_contig@0 { + heap-name = "sys_contig"; + heap-id = <0x1>; + heap-base = <0x0>; + heap-size = <0x0>; + heap-type = "ion_system_contig"; + }; + }; diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt new file mode 100644 index 000000000000..66223d561972 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt @@ -0,0 +1,63 @@ +* Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs + +Required properties: +- compatible : Must include "fsl,qoriq-tmu". The version of the device is + determined by the TMU IP Block Revision Register (IPBRR0) at + offset 0x0BF8. + Table of correspondences between IPBRR0 values and example chips: + Value Device + ---------- ----- + 0x01900102 T1040 +- reg : Address range of TMU registers. +- interrupts : Contains the interrupt for TMU. +- fsl,tmu-range : The values to be programmed into TTRnCR, as specified by + the SoC reference manual. The first cell is TTR0CR, the second is + TTR1CR, etc. +- fsl,tmu-calibration : A list of cell pairs containing temperature + calibration data, as specified by the SoC reference manual. + The first cell of each pair is the value to be written to TTCFGR, + and the second is the value to be written to TSCFGR. + +Example: + +tmu@f0000 { + compatible = "fsl,qoriq-tmu"; + reg = <0xf0000 0x1000>; + interrupts = <18 2 0 0>; + fsl,tmu-range = <0x000a0000 0x00090026 0x0008004a 0x0001006a>; + fsl,tmu-calibration = <0x00000000 0x00000025 + 0x00000001 0x00000028 + 0x00000002 0x0000002d + 0x00000003 0x00000031 + 0x00000004 0x00000036 + 0x00000005 0x0000003a + 0x00000006 0x00000040 + 0x00000007 0x00000044 + 0x00000008 0x0000004a + 0x00000009 0x0000004f + 0x0000000a 0x00000054 + + 0x00010000 0x0000000d + 0x00010001 0x00000013 + 0x00010002 0x00000019 + 0x00010003 0x0000001f + 0x00010004 0x00000025 + 0x00010005 0x0000002d + 0x00010006 0x00000033 + 0x00010007 0x00000043 + 0x00010008 0x0000004b + 0x00010009 0x00000053 + + 0x00020000 0x00000010 + 0x00020001 0x00000017 + 0x00020002 0x0000001f + 0x00020003 0x00000029 + 0x00020004 0x00000031 + 0x00020005 0x0000003c + 0x00020006 0x00000042 + 0x00020007 0x0000004d + 0x00020008 0x00000056 + + 0x00030000 0x00000012 + 0x00030001 0x0000001d>; +}; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index fd132cbee70e..221368207ca4 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -4,6 +4,7 @@ Platform DesignWare HS OTG USB 2.0 controller Required properties: - compatible : One of: - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC. + - hisilicon,hi6220-usb: The DWC2 USB controller instance in the hi6220 SoC. - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; diff --git a/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt new file mode 100644 index 000000000000..30361b32a460 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt @@ -0,0 +1,33 @@ +Xilinx SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: Should contain "xlnx,zynqmp-dwc3" +- clocks: A list of phandles for the clocks listed in clock-names +- clock-names: Should contain the following: + "bus_clk" Master/Core clock, have to be >= 125 MHz for SS + operation and >= 60MHz for HS operation + + "ref_clk" Clock source to core during PHY power down + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Example device node: + + usb@0 { + #address-cells = <0x2>; + #size-cells = <0x1>; + status = "okay"; + compatible = "xlnx,zynqmp-dwc3"; + clock-names = "bus_clk" "ref_clk"; + clocks = <&clk125>, <&clk125>; + ranges; + + dwc3@fe200000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe200000 0x40000>; + interrupts = <0x0 0x41 0x4>; + dr_mode = "host"; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt new file mode 100644 index 000000000000..b3a7ffa48852 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt @@ -0,0 +1,51 @@ +MT8173 xHCI + +The device node for Mediatek SOC USB3.0 host controller + +Required properties: + - compatible : should contain "mediatek,mt8173-xhci" + - reg : specifies physical base address and size of the registers, + the first one for MAC, the second for IPPC + - interrupts : interrupt used by the controller + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain + "sys_ck": for clock of xHCI MAC + "wakeup_deb_p0": for USB wakeup debounce clock of port0 + "wakeup_deb_p1": for USB wakeup debounce clock of port1 + + - phys : a list of phandle + phy specifier pairs + +Optional properties: + - mediatek,wakeup-src : 1: ip sleep wakeup mode; 2: line state wakeup + mode; + - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup + control register, it depends on "mediatek,wakeup-src". + - vbus-supply : reference to the VBUS regulator; + - usb3-lpm-capable : supports USB3.0 LPM + +Example: +usb30: usb@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>, + <0 0x11280700 0 0x0100>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, + <&pericfg CLK_PERI_USB0>, + <&pericfg CLK_PERI_USB1>; + clock-names = "sys_ck", + "wakeup_deb_p0", + "wakeup_deb_p1"; + phys = <&phy_port0 PHY_TYPE_USB3>, + <&phy_port1 PHY_TYPE_USB2>; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p1_vbus>; + usb3-lpm-capable; + mediatek,syscon-wakeup = <&pericfg>; + mediatek,wakeup-src = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/octeon-usb.txt b/Documentation/devicetree/bindings/usb/octeon-usb.txt new file mode 100644 index 000000000000..205c8d24d6e3 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/octeon-usb.txt @@ -0,0 +1,62 @@ +OCTEON/OCTEON+ USB BLOCK + +1) Main node + + Required properties: + + - compatible: must be "cavium,octeon-5750-usbn" + + - reg: specifies the physical base address of the USBN block and + the length of the memory mapped region. + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 2. + + - #size-cells: specifies the number of cells used to represent the size + of an address. The value must be 2. + + - ranges: specifies the translation between child address space and parent + address space. + + - clock-frequency: speed of the USB reference clock. Allowed values are + 12000000, 24000000 or 48000000. + + - cavium,refclk-type: type of the USB reference clock. Allowed values are + "crystal" or "external". + + - refclk-frequency: deprecated, use "clock-frequency". + + - refclk-type: deprecated, use "cavium,refclk-type". + +2) Child node + + The main node must have one child node which describes the built-in + USB controller. + + Required properties: + + - compatible: must be "cavium,octeon-5750-usbc" + + - reg: specifies the physical base address of the USBC block and + the length of the memory mapped region. + + - interrupts: specifies the interrupt number for the USB controller. + +3) Example: + + usbn: usbn@1180068000000 { + compatible = "cavium,octeon-5750-usbn"; + reg = <0x11800 0x68000000 0x0 0x1000>; + ranges; /* Direct mapping */ + #address-cells = <2>; + #size-cells = <2>; + clock-frequency = <12000000>; + cavium,refclk-type = "crystal"; + + usbc@16f0010000000 { + compatible = "cavium,octeon-5750-usbc"; + reg = <0x16f00 0x10000000 0x0 0x80000>; + interrupts = <0 56>; + }; + }; + diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas_usb3.txt new file mode 100644 index 000000000000..8d52766f07b9 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/renesas_usb3.txt @@ -0,0 +1,23 @@ +Renesas Electronics USB3.0 Peripheral driver + +Required properties: + - compatible: Must contain one of the following: + - "renesas,r8a7795-usb3-peri" + - reg: Base address and length of the register for the USB3.0 Peripheral + - interrupts: Interrupt specifier for the USB3.0 Peripheral + - clocks: clock phandle and specifier pair + +Example: + usb3_peri0: usb@ee020000 { + compatible = "renesas,r8a7795-usb3-peri"; + reg = <0 0xee020000 0 0x400>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 328>; + }; + + usb3_peri1: usb@ee060000 { + compatible = "renesas,r8a7795-usb3-peri"; + reg = <0 0xee060000 0 0x400>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 327>; + }; diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 7d48f63db44e..b6040563e51a 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -1,11 +1,21 @@ Renesas Electronics USBHS driver Required properties: - - compatible: Must contain one of the following: - - "renesas,usbhs-r8a7790" - - "renesas,usbhs-r8a7791" - - "renesas,usbhs-r8a7794" - - "renesas,usbhs-r8a7795" + - compatible: Must contain one or more of the following: + + - "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device + - "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device + - "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device + - "renesas,usbhs-r8a7793" for r8a7793 (R-Car M2-N) compatible device + - "renesas,usbhs-r8a7794" for r8a7794 (R-Car E2) compatible device + - "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device + - "renesas,rcar-gen2-usbhs" for R-Car Gen2 compatible device + - "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first followed + by the generic version. + - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - clocks: A list of phandle + clock specifier pairs @@ -22,7 +32,7 @@ Optional properties: Example: usbhs: usb@e6590000 { - compatible = "renesas,usbhs-r8a7790"; + compatible = "renesas,usbhs-r8a7790", "renesas,rcar-gen2-usbhs"; reg = <0 0xe6590000 0 0x100>; interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp7_clks R8A7790_CLK_HSUSB>; diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 86f67f0886bc..082573289f1e 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -3,8 +3,8 @@ USB xHCI controllers Required properties: - compatible: should be one of "generic-xhci", "marvell,armada-375-xhci", "marvell,armada-380-xhci", - "renesas,xhci-r8a7790", "renesas,xhci-r8a7791" (deprecated: - "xhci-platform"). + "renesas,xhci-r8a7790", "renesas,xhci-r8a7791", "renesas,xhci-r8a7793", + "renesas,xhci-r8a7795" (deprecated: "xhci-platform"). - reg: should contain address and length of the standard XHCI register set for the device. - interrupts: one XHCI interrupt should be described here. diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt index 52493b1480e2..c1a0a9191d26 100644 --- a/Documentation/devicetree/bindings/usb/usb3503.txt +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -18,7 +18,8 @@ Optional properties: - refclk: Clock used for driving REFCLK signal (optional, if not provided the driver assumes that clock signal is always available, its rate is specified by REF_SEL pins and a value from the primary - reference clock frequencies table is used) + reference clock frequencies table is used). Use clocks and + clock-names in order to assign it - refclk-frequency: Frequency of the REFCLK signal as defined by REF_SEL pins (optional, if not provided, driver will not set rate of the REFCLK signal and assume that a value from the primary reference @@ -33,4 +34,6 @@ Examples: intn-gpios = <&gpx3 4 1>; reset-gpios = <&gpx3 5 1>; initial-mode = <1>; + clocks = <&clks 80>; + clock-names = "refclk"; }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 55df1d444e9f..a4f2035569ce 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -161,6 +161,7 @@ nuvoton Nuvoton Technology Corporation nvidia NVIDIA nxp NXP Semiconductors okaya Okaya Electric America, Inc. +olimex OLIMEX Ltd. onnn ON Semiconductor Corp. opencores OpenCores.org option Option NV diff --git a/Documentation/dmaengine/client.txt b/Documentation/dmaengine/client.txt index 11fb87ff6cd0..9e33189745f0 100644 --- a/Documentation/dmaengine/client.txt +++ b/Documentation/dmaengine/client.txt @@ -22,25 +22,14 @@ The slave DMA usage consists of following steps: Channel allocation is slightly different in the slave DMA context, client drivers typically need a channel from a particular DMA controller only and even in some cases a specific channel is desired. - To request a channel dma_request_channel() API is used. + To request a channel dma_request_chan() API is used. Interface: - struct dma_chan *dma_request_channel(dma_cap_mask_t mask, - dma_filter_fn filter_fn, - void *filter_param); - where dma_filter_fn is defined as: - typedef bool (*dma_filter_fn)(struct dma_chan *chan, void *filter_param); + struct dma_chan *dma_request_chan(struct device *dev, const char *name); - The 'filter_fn' parameter is optional, but highly recommended for - slave and cyclic channels as they typically need to obtain a specific - DMA channel. - - When the optional 'filter_fn' parameter is NULL, dma_request_channel() - simply returns the first channel that satisfies the capability mask. - - Otherwise, the 'filter_fn' routine will be called once for each free - channel which has a capability in 'mask'. 'filter_fn' is expected to - return 'true' when the desired DMA channel is found. + Which will find and return the 'name' DMA channel associated with the 'dev' + device. The association is done via DT, ACPI or board file based + dma_slave_map matching table. A channel allocated via this interface is exclusive to the caller, until dma_release_channel() is called. @@ -128,7 +117,7 @@ The slave DMA usage consists of following steps: transaction. For cyclic DMA, a callback function may wish to terminate the - DMA via dmaengine_terminate_all(). + DMA via dmaengine_terminate_async(). Therefore, it is important that DMA engine drivers drop any locks before calling the callback function which may cause a @@ -166,12 +155,29 @@ The slave DMA usage consists of following steps: Further APIs: -1. int dmaengine_terminate_all(struct dma_chan *chan) +1. int dmaengine_terminate_sync(struct dma_chan *chan) + int dmaengine_terminate_async(struct dma_chan *chan) + int dmaengine_terminate_all(struct dma_chan *chan) /* DEPRECATED */ This causes all activity for the DMA channel to be stopped, and may discard data in the DMA FIFO which hasn't been fully transferred. No callback functions will be called for any incomplete transfers. + Two variants of this function are available. + + dmaengine_terminate_async() might not wait until the DMA has been fully + stopped or until any running complete callbacks have finished. But it is + possible to call dmaengine_terminate_async() from atomic context or from + within a complete callback. dmaengine_synchronize() must be called before it + is safe to free the memory accessed by the DMA transfer or free resources + accessed from within the complete callback. + + dmaengine_terminate_sync() will wait for the transfer and any running + complete callbacks to finish before it returns. But the function must not be + called from atomic context or from within a complete callback. + + dmaengine_terminate_all() is deprecated and should not be used in new code. + 2. int dmaengine_pause(struct dma_chan *chan) This pauses activity on the DMA channel without data loss. @@ -197,3 +203,20 @@ Further APIs: a running DMA channel. It is recommended that DMA engine users pause or stop (via dmaengine_terminate_all()) the channel before using this API. + +5. void dmaengine_synchronize(struct dma_chan *chan) + + Synchronize the termination of the DMA channel to the current context. + + This function should be used after dmaengine_terminate_async() to synchronize + the termination of the DMA channel to the current context. The function will + wait for the transfer and any running complete callbacks to finish before it + returns. + + If dmaengine_terminate_async() is used to stop the DMA channel this function + must be called before it is safe to free memory accessed by previously + submitted descriptors or to free any resources accessed within the complete + callback of previously submitted descriptors. + + The behavior of this function is undefined if dma_async_issue_pending() has + been called between dmaengine_terminate_async() and this function. diff --git a/Documentation/dmaengine/provider.txt b/Documentation/dmaengine/provider.txt index 67d4ce4df109..122b7f4876bb 100644 --- a/Documentation/dmaengine/provider.txt +++ b/Documentation/dmaengine/provider.txt @@ -327,8 +327,24 @@ supported. * device_terminate_all - Aborts all the pending and ongoing transfers on the channel - - This command should operate synchronously on the channel, - terminating right away all the channels + - For aborted transfers the complete callback should not be called + - Can be called from atomic context or from within a complete + callback of a descriptor. Must not sleep. Drivers must be able + to handle this correctly. + - Termination may be asynchronous. The driver does not have to + wait until the currently active transfer has completely stopped. + See device_synchronize. + + * device_synchronize + - Must synchronize the termination of a channel to the current + context. + - Must make sure that memory for previously submitted + descriptors is no longer accessed by the DMA controller. + - Must make sure that all complete callbacks for previously + submitted descriptors have finished running and none are + scheduled to run. + - May sleep. + Misc notes (stuff that should be documented, but don't really know where to put them) diff --git a/Documentation/filesystems/f2fs.txt b/Documentation/filesystems/f2fs.txt index b102b436563e..e1c9f0849da6 100644 --- a/Documentation/filesystems/f2fs.txt +++ b/Documentation/filesystems/f2fs.txt @@ -102,7 +102,7 @@ background_gc=%s Turn on/off cleaning operations, namely garbage collection, triggered in background when I/O subsystem is idle. If background_gc=on, it will turn on the garbage collection and if background_gc=off, garbage collection - will be truned off. If background_gc=sync, it will turn + will be turned off. If background_gc=sync, it will turn on synchronous garbage collection running in background. Default value for this option is on. So garbage collection is on by default. @@ -145,10 +145,12 @@ extent_cache Enable an extent cache based on rb-tree, it can cache as many as extent which map between contiguous logical address and physical address per inode, resulting in increasing the cache hit ratio. Set by default. -noextent_cache Diable an extent cache based on rb-tree explicitly, see +noextent_cache Disable an extent cache based on rb-tree explicitly, see the above extent_cache mount option. noinline_data Disable the inline data feature, inline data feature is enabled by default. +data_flush Enable data flushing before checkpoint in order to + persist data of regular and symlink. ================================================================================ DEBUGFS ENTRIES @@ -192,7 +194,7 @@ Files in /sys/fs/f2fs/<devname> policy for garbage collection. Setting gc_idle = 0 (default) will disable this option. Setting gc_idle = 1 will select the Cost Benefit approach - & setting gc_idle = 2 will select the greedy aproach. + & setting gc_idle = 2 will select the greedy approach. reclaim_segments This parameter controls the number of prefree segments to be reclaimed. If the number of prefree @@ -298,7 +300,7 @@ The dump.f2fs shows the information of specific inode and dumps SSA and SIT to file. Each file is dump_ssa and dump_sit. The dump.f2fs is used to debug on-disk data structures of the f2fs filesystem. -It shows on-disk inode information reconized by a given inode number, and is +It shows on-disk inode information recognized by a given inode number, and is able to dump all the SSA and SIT entries into predefined files, ./dump_ssa and ./dump_sit respectively. diff --git a/Documentation/filesystems/porting b/Documentation/filesystems/porting index 0f88e6020487..f1b87d8aa2da 100644 --- a/Documentation/filesystems/porting +++ b/Documentation/filesystems/porting @@ -508,7 +508,11 @@ in your dentry operations instead. [mandatory] any symlink that might use page_follow_link_light/page_put_link() must have inode_nohighmem(inode) called before anything might start playing with - its pagecache. + its pagecache. No highmem pages should end up in the pagecache of such + symlinks. That includes any preseeding that might be done during symlink + creation. __page_symlink() will honour the mapping gfp flags, so once + you've done inode_nohighmem() it's safe to use, but if you allocate and + insert the page manually, make sure to use the right gfp flags. -- [mandatory] ->follow_link() is replaced with ->get_link(); same API, except that diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt index 402ab99e409f..e95aa1c6eadf 100644 --- a/Documentation/filesystems/proc.txt +++ b/Documentation/filesystems/proc.txt @@ -169,6 +169,9 @@ read the file /proc/PID/status: VmLck: 0 kB VmHWM: 476 kB VmRSS: 476 kB + RssAnon: 352 kB + RssFile: 120 kB + RssShmem: 4 kB VmData: 156 kB VmStk: 88 kB VmExe: 68 kB @@ -231,14 +234,20 @@ Table 1-2: Contents of the status files (as of 4.1) VmSize total program size VmLck locked memory size VmHWM peak resident set size ("high water mark") - VmRSS size of memory portions + VmRSS size of memory portions. It contains the three + following parts (VmRSS = RssAnon + RssFile + RssShmem) + RssAnon size of resident anonymous memory + RssFile size of resident file mappings + RssShmem size of resident shmem memory (includes SysV shm, + mapping of tmpfs and shared anonymous mappings) VmData size of data, stack, and text segments VmStk size of data, stack, and text segments VmExe size of text segment VmLib size of shared library code VmPTE size of page table entries VmPMD size of second level page tables - VmSwap size of swap usage (the number of referred swapents) + VmSwap amount of swap used by anonymous private data + (shmem swap usage is not included) HugetlbPages size of hugetlb memory portions Threads number of threads SigQ number of signals queued/max. number for queue @@ -265,7 +274,8 @@ Table 1-3: Contents of the statm files (as of 2.6.8-rc3) Field Content size total program size (pages) (same as VmSize in status) resident size of memory portions (pages) (same as VmRSS in status) - shared number of pages that are shared (i.e. backed by a file) + shared number of pages that are shared (i.e. backed by a file, same + as RssFile+RssShmem in status) trs number of pages that are 'code' (not including libs; broken, includes data segment) lrs number of pages of library (always 0 on 2.6) @@ -459,7 +469,10 @@ and a page is modified, the file page is replaced by a private anonymous copy. hugetlbfs page which is *not* counted in "RSS" or "PSS" field for historical reasons. And these are not included in {Shared,Private}_{Clean,Dirty} field. "Swap" shows how much would-be-anonymous memory is also used, but out on swap. -"SwapPss" shows proportional swap share of this mapping. +For shmem mappings, "Swap" includes also the size of the mapped (and not +replaced by copy-on-write) part of the underlying shmem object out on swap. +"SwapPss" shows proportional swap share of this mapping. Unlike "Swap", this +does not take into account swapped out page of underlying shmem objects. "Locked" indicates whether the mapping is locked in memory or not. "VmFlags" field deserves a separate description. This member represents the kernel @@ -842,6 +855,7 @@ Dirty: 968 kB Writeback: 0 kB AnonPages: 861800 kB Mapped: 280372 kB +Shmem: 644 kB Slab: 284364 kB SReclaimable: 159856 kB SUnreclaim: 124508 kB @@ -898,6 +912,7 @@ MemAvailable: An estimate of how much memory is available for starting new AnonPages: Non-file backed pages mapped into userspace page tables AnonHugePages: Non-file backed huge pages mapped into userspace page tables Mapped: files which have been mmaped, such as libraries + Shmem: Total memory used by shared memory (shmem) and tmpfs Slab: in-kernel data structures cache SReclaimable: Part of Slab, that might be reclaimed, such as caches SUnreclaim: Part of Slab, that cannot be reclaimed on memory pressure diff --git a/Documentation/filesystems/tmpfs.txt b/Documentation/filesystems/tmpfs.txt index 98ef55124158..d392e1505f17 100644 --- a/Documentation/filesystems/tmpfs.txt +++ b/Documentation/filesystems/tmpfs.txt @@ -17,10 +17,10 @@ RAM, where you have to create an ordinary filesystem on top. Ramdisks cannot swap and you do not have the possibility to resize them. Since tmpfs lives completely in the page cache and on swap, all tmpfs -pages currently in memory will show up as cached. It will not show up -as shared or something like that. Further on you can check the actual -RAM+swap use of a tmpfs instance with df(1) and du(1). - +pages will be shown as "Shmem" in /proc/meminfo and "Shared" in +free(1). Notice that these counters also include shared memory +(shmem, see ipcs(1)). The most reliable way to get the count is +using df(1) and du(1). tmpfs has the following uses: diff --git a/Documentation/iio/iio_configfs.txt b/Documentation/iio/iio_configfs.txt new file mode 100644 index 000000000000..f0add35cd52e --- /dev/null +++ b/Documentation/iio/iio_configfs.txt @@ -0,0 +1,93 @@ +Industrial IIO configfs support + +1. Overview + +Configfs is a filesystem-based manager of kernel objects. IIO uses some +objects that could be easily configured using configfs (e.g.: devices, +triggers). + +See Documentation/filesystems/configfs/configfs.txt for more information +about how configfs works. + +2. Usage + +In order to use configfs support in IIO we need to select it at compile +time via CONFIG_IIO_CONFIGFS config option. + +Then, mount the configfs filesystem (usually under /config directory): + +$ mkdir /config +$ mount -t configfs none /config + +At this point, all default IIO groups will be created and can be accessed +under /config/iio. Next chapters will describe available IIO configuration +objects. + +3. Software triggers + +One of the IIO default configfs groups is the "triggers" group. It is +automagically accessible when the configfs is mounted and can be found +under /config/iio/triggers. + +IIO software triggers implementation offers support for creating multiple +trigger types. A new trigger type is usually implemented as a separate +kernel module following the interface in include/linux/iio/sw_trigger.h: + +/* + * drivers/iio/trigger/iio-trig-sample.c + * sample kernel module implementing a new trigger type + */ +#include <linux/iio/sw_trigger.h> + + +static struct iio_sw_trigger *iio_trig_sample_probe(const char *name) +{ + /* + * This allocates and registers an IIO trigger plus other + * trigger type specific initialization. + */ +} + +static int iio_trig_hrtimer_remove(struct iio_sw_trigger *swt) +{ + /* + * This undoes the actions in iio_trig_sample_probe + */ +} + +static const struct iio_sw_trigger_ops iio_trig_sample_ops = { + .probe = iio_trig_sample_probe, + .remove = iio_trig_sample_remove, +}; + +static struct iio_sw_trigger_type iio_trig_sample = { + .name = "trig-sample", + .owner = THIS_MODULE, + .ops = &iio_trig_sample_ops, +}; + +module_iio_sw_trigger_driver(iio_trig_sample); + +Each trigger type has its own directory under /config/iio/triggers. Loading +iio-trig-sample module will create 'trig-sample' trigger type directory +/config/iio/triggers/trig-sample. + +We support the following interrupt sources (trigger types): + * hrtimer, uses high resolution timers as interrupt source + +3.1 Hrtimer triggers creation and destruction + +Loading iio-trig-hrtimer module will register hrtimer trigger types allowing +users to create hrtimer triggers under /config/iio/triggers/hrtimer. + +e.g: + +$ mkdir /config/triggers/hrtimer/instance1 +$ rmdir /config/triggers/hrtimer/instance1 + +Each trigger can have one or more attributes specific to the trigger type. + +3.2 "hrtimer" trigger types attributes + +"hrtimer" trigger type doesn't have any configurable attribute from /config dir. +It does introduce the sampling_frequency attribute to trigger directory. diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 1a8169ba29e6..5a6235ed3663 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -608,6 +608,10 @@ bytes respectively. Such letter suffixes can also be entirely omitted. cut the overhead, others just disable the usage. So only cgroup_disable=memory is actually worthy} + cgroup.memory= [KNL] Pass options to the cgroup memory controller. + Format: <string> + nosocket -- Disable socket memory accounting. + checkreqprot [SELINUX] Set initial checkreqprot flag value. Format: { "0" | "1" } See security/selinux/Kconfig help text. @@ -730,16 +734,17 @@ bytes respectively. Such letter suffixes can also be entirely omitted. uart[8250],io,<addr>[,options] uart[8250],mmio,<addr>[,options] + uart[8250],mmio16,<addr>[,options] uart[8250],mmio32,<addr>[,options] uart[8250],0x<addr>[,options] Start an early, polled-mode console on the 8250/16550 UART at the specified I/O port or MMIO address, switching to the matching ttyS device later. MMIO inter-register address stride is either 8-bit - (mmio) or 32-bit (mmio32). - If none of [io|mmio|mmio32], <addr> is assumed to be - equivalent to 'mmio'. 'options' are specified in the - same format described for ttyS above; if unspecified, + (mmio), 16-bit (mmio16), or 32-bit (mmio32). + If none of [io|mmio|mmio16|mmio32], <addr> is assumed + to be equivalent to 'mmio'. 'options' are specified in + the same format described for ttyS above; if unspecified, the h/w is not re-initialized. hvc<n> Use the hypervisor console device <n>. This is for @@ -1011,10 +1016,13 @@ bytes respectively. Such letter suffixes can also be entirely omitted. unspecified, the h/w is not initialized. pl011,<addr> + pl011,mmio32,<addr> Start an early, polled-mode console on a pl011 serial port at the specified address. The pl011 serial port must already be setup and configured. Options are not - yet supported. + yet supported. If 'mmio32' is specified, then only + the driver will use only 32-bit accessors to read/write + the device registers. msm_serial,<addr> Start an early, polled-mode console on an msm serial @@ -2584,8 +2592,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted. notsc [BUGS=X86-32] Disable Time Stamp Counter - nousb [USB] Disable the USB subsystem - nowatchdog [KNL] Disable both lockup detectors, i.e. soft-lockup and NMI watchdog (hard-lockup). @@ -2987,6 +2993,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. may be specified. Format: <port>,<port>.... + ppc_strict_facility_enable + [PPC] This option catches any kernel floating point, + Altivec, VSX and SPE outside of regions specifically + allowed (eg kernel_enable_fpu()/kernel_disable_fpu()). + There is some performance impact when enabling this. + print-fatal-signals= [KNL] debug: print fatal signals @@ -3900,6 +3912,10 @@ bytes respectively. Such letter suffixes can also be entirely omitted. usbcore.usbfs_snoop= [USB] Set to log all usbfs traffic (default 0 = off). + usbcore.usbfs_snoop_max= + [USB] Maximum number of bytes to snoop in each URB + (default = 65536). + usbcore.blinkenlights= [USB] Set to cycle leds on hubs (default 0 = off). @@ -3920,6 +3936,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted. USB_REQ_GET_DESCRIPTOR request in milliseconds (default 5000 = 5.0 seconds). + usbcore.nousb [USB] Disable the USB subsystem + usbhid.mousepoll= [USBHID] The interval which mice are to be polled at. diff --git a/Documentation/md-cluster.txt b/Documentation/md-cluster.txt index 1b794369e03a..c100c7163507 100644 --- a/Documentation/md-cluster.txt +++ b/Documentation/md-cluster.txt @@ -3,7 +3,7 @@ The cluster MD is a shared-device RAID for a cluster. 1. On-disk format -Separate write-intent-bitmap are used for each cluster node. +Separate write-intent-bitmaps are used for each cluster node. The bitmaps record all writes that may have been started on that node, and may not yet have finished. The on-disk layout is: @@ -14,117 +14,161 @@ and may not yet have finished. The on-disk layout is: | bm super[2] + bits | bm bits [2, contd] | bm super[3] + bits | | bm bits [3, contd] | | | -During "normal" functioning we assume the filesystem ensures that only one -node writes to any given block at a time, so a write -request will +During "normal" functioning we assume the filesystem ensures that only +one node writes to any given block at a time, so a write request will + - set the appropriate bit (if not already set) - commit the write to all mirrors - schedule the bit to be cleared after a timeout. -Reads are just handled normally. It is up to the filesystem to -ensure one node doesn't read from a location where another node (or the same +Reads are just handled normally. It is up to the filesystem to ensure +one node doesn't read from a location where another node (or the same node) is writing. 2. DLM Locks for management -There are two locks for managing the device: +There are three groups of locks for managing the device: 2.1 Bitmap lock resource (bm_lockres) - The bm_lockres protects individual node bitmaps. They are named in the - form bitmap001 for node 1, bitmap002 for node and so on. When a node - joins the cluster, it acquires the lock in PW mode and it stays so - during the lifetime the node is part of the cluster. The lock resource - number is based on the slot number returned by the DLM subsystem. Since - DLM starts node count from one and bitmap slots start from zero, one is - subtracted from the DLM slot number to arrive at the bitmap slot number. + The bm_lockres protects individual node bitmaps. They are named in + the form bitmap000 for node 1, bitmap001 for node 2 and so on. When a + node joins the cluster, it acquires the lock in PW mode and it stays + so during the lifetime the node is part of the cluster. The lock + resource number is based on the slot number returned by the DLM + subsystem. Since DLM starts node count from one and bitmap slots + start from zero, one is subtracted from the DLM slot number to arrive + at the bitmap slot number. + + The LVB of the bitmap lock for a particular node records the range + of sectors that are being re-synced by that node. No other + node may write to those sectors. This is used when a new nodes + joins the cluster. + +2.2 Message passing locks + + Each node has to communicate with other nodes when starting or ending + resync, and for metadata superblock updates. This communication is + managed through three locks: "token", "message", and "ack", together + with the Lock Value Block (LVB) of one of the "message" lock. + +2.3 new-device management + + A single lock: "no-new-dev" is used to co-ordinate the addition of + new devices - this must be synchronized across the array. + Normally all nodes hold a concurrent-read lock on this device. 3. Communication -Each node has to communicate with other nodes when starting or ending -resync, and metadata superblock updates. + Messages can be broadcast to all nodes, and the sender waits for all + other nodes to acknowledge the message before proceeding. Only one + message can be processed at a time. 3.1 Message Types - There are 3 types, of messages which are passed + There are six types of messages which are passed: - 3.1.1 METADATA_UPDATED: informs other nodes that the metadata has been - updated, and the node must re-read the md superblock. This is performed - synchronously. + 3.1.1 METADATA_UPDATED: informs other nodes that the metadata has + been updated, and the node must re-read the md superblock. This is + performed synchronously. It is primarily used to signal device + failure. - 3.1.2 RESYNC: informs other nodes that a resync is initiated or ended - so that each node may suspend or resume the region. + 3.1.2 RESYNCING: informs other nodes that a resync is initiated or + ended so that each node may suspend or resume the region. Each + RESYNCING message identifies a range of the devices that the + sending node is about to resync. This over-rides any pervious + notification from that node: only one ranged can be resynced at a + time per-node. + + 3.1.3 NEWDISK: informs other nodes that a device is being added to + the array. Message contains an identifier for that device. See + below for further details. + + 3.1.4 REMOVE: A failed or spare device is being removed from the + array. The slot-number of the device is included in the message. + + 3.1.5 RE_ADD: A failed device is being re-activated - the assumption + is that it has been determined to be working again. + + 3.1.6 BITMAP_NEEDS_SYNC: if a node is stopped locally but the bitmap + isn't clean, then another node is informed to take the ownership of + resync. 3.2 Communication mechanism The DLM LVB is used to communicate within nodes of the cluster. There are three resources used for the purpose: - 3.2.1 Token: The resource which protects the entire communication + 3.2.1 token: The resource which protects the entire communication system. The node having the token resource is allowed to communicate. - 3.2.2 Message: The lock resource which carries the data to + 3.2.2 message: The lock resource which carries the data to communicate. - 3.2.3 Ack: The resource, acquiring which means the message has been + 3.2.3 ack: The resource, acquiring which means the message has been acknowledged by all nodes in the cluster. The BAST of the resource - is used to inform the receive node that a node wants to communicate. + is used to inform the receiving node that a node wants to + communicate. The algorithm is: - 1. receive status + 1. receive status - all nodes have concurrent-reader lock on "ack". - sender receiver receiver - ACK:CR ACK:CR ACK:CR + sender receiver receiver + "ack":CR "ack":CR "ack":CR - 2. sender get EX of TOKEN - sender get EX of MESSAGE + 2. sender get EX on "token" + sender get EX on "message" sender receiver receiver - TOKEN:EX ACK:CR ACK:CR - MESSAGE:EX - ACK:CR + "token":EX "ack":CR "ack":CR + "message":EX + "ack":CR - Sender checks that it still needs to send a message. Messages received - or other events that happened while waiting for the TOKEN may have made - this message inappropriate or redundant. + Sender checks that it still needs to send a message. Messages + received or other events that happened while waiting for the + "token" may have made this message inappropriate or redundant. - 3. sender write LVB. - sender down-convert MESSAGE from EX to CW - sender try to get EX of ACK - [ wait until all receiver has *processed* the MESSAGE ] + 3. sender writes LVB. + sender down-convert "message" from EX to CW + sender try to get EX of "ack" + [ wait until all receivers have *processed* the "message" ] - [ triggered by bast of ACK ] - receiver get CR of MESSAGE + [ triggered by bast of "ack" ] + receiver get CR on "message" receiver read LVB receiver processes the message [ wait finish ] - receiver release ACK - - sender receiver receiver - TOKEN:EX MESSAGE:CR MESSAGE:CR - MESSAGE:CR - ACK:EX - - 4. triggered by grant of EX on ACK (indicating all receivers have processed - message) - sender down-convert ACK from EX to CR - sender release MESSAGE - sender release TOKEN - receiver upconvert to PR of MESSAGE - receiver get CR of ACK - receiver release MESSAGE + receiver releases "ack" + receiver tries to get PR on "message" + + sender receiver receiver + "token":EX "message":CR "message":CR + "message":CW + "ack":EX + + 4. triggered by grant of EX on "ack" (indicating all receivers + have processed message) + sender down-converts "ack" from EX to CR + sender releases "message" + sender releases "token" + receiver upconvert to PR on "message" + receiver get CR of "ack" + receiver release "message" sender receiver receiver - ACK:CR ACK:CR ACK:CR + "ack":CR "ack":CR "ack":CR 4. Handling Failures 4.1 Node Failure - When a node fails, the DLM informs the cluster with the slot. The node - starts a cluster recovery thread. The cluster recovery thread: + + When a node fails, the DLM informs the cluster with the slot + number. The node starts a cluster recovery thread. The cluster + recovery thread: + - acquires the bitmap<number> lock of the failed node - opens the bitmap - reads the bitmap of the failed node @@ -132,45 +176,143 @@ The algorithm is: - cleans the bitmap of the failed node - releases bitmap<number> lock of the failed node - initiates resync of the bitmap on the current node + md_check_recovery is invoked within recover_bitmaps, + then md_check_recovery -> metadata_update_start/finish, + it will lock the communication by lock_comm. + Which means when one node is resyncing it blocks all + other nodes from writing anywhere on the array. - The resync process, is the regular md resync. However, in a clustered + The resync process is the regular md resync. However, in a clustered environment when a resync is performed, it needs to tell other nodes of the areas which are suspended. Before a resync starts, the node - send out RESYNC_START with the (lo,hi) range of the area which needs - to be suspended. Each node maintains a suspend_list, which contains - the list of ranges which are currently suspended. On receiving - RESYNC_START, the node adds the range to the suspend_list. Similarly, - when the node performing resync finishes, it send RESYNC_FINISHED - to other nodes and other nodes remove the corresponding entry from - the suspend_list. + send out RESYNCING with the (lo,hi) range of the area which needs to + be suspended. Each node maintains a suspend_list, which contains the + list of ranges which are currently suspended. On receiving RESYNCING, + the node adds the range to the suspend_list. Similarly, when the node + performing resync finishes, it sends RESYNCING with an empty range to + other nodes and other nodes remove the corresponding entry from the + suspend_list. - A helper function, should_suspend() can be used to check if a particular - I/O range should be suspended or not. + A helper function, ->area_resyncing() can be used to check if a + particular I/O range should be suspended or not. 4.2 Device Failure + Device failures are handled and communicated with the metadata update - routine. + routine. When a node detects a device failure it does not allow + any further writes to that device until the failure has been + acknowledged by all other nodes. 5. Adding a new Device -For adding a new device, it is necessary that all nodes "see" the new device -to be added. For this, the following algorithm is used: + + For adding a new device, it is necessary that all nodes "see" the new + device to be added. For this, the following algorithm is used: 1. Node 1 issues mdadm --manage /dev/mdX --add /dev/sdYY which issues - ioctl(ADD_NEW_DISC with disc.state set to MD_DISK_CLUSTER_ADD) - 2. Node 1 sends NEWDISK with uuid and slot number + ioctl(ADD_NEW_DISK with disc.state set to MD_DISK_CLUSTER_ADD) + 2. Node 1 sends a NEWDISK message with uuid and slot number 3. Other nodes issue kobject_uevent_env with uuid and slot number (Steps 4,5 could be a udev rule) 4. In userspace, the node searches for the disk, perhaps using blkid -t SUB_UUID="" - 5. Other nodes issue either of the following depending on whether the disk - was found: + 5. Other nodes issue either of the following depending on whether + the disk was found: ioctl(ADD_NEW_DISK with disc.state set to MD_DISK_CANDIDATE and - disc.number set to slot number) + disc.number set to slot number) ioctl(CLUSTERED_DISK_NACK) - 6. Other nodes drop lock on no-new-devs (CR) if device is found - 7. Node 1 attempts EX lock on no-new-devs - 8. If node 1 gets the lock, it sends METADATA_UPDATED after unmarking the disk - as SpareLocal - 9. If not (get no-new-dev lock), it fails the operation and sends METADATA_UPDATED - 10. Other nodes get the information whether a disk is added or not - by the following METADATA_UPDATED. + 6. Other nodes drop lock on "no-new-devs" (CR) if device is found + 7. Node 1 attempts EX lock on "no-new-dev" + 8. If node 1 gets the lock, it sends METADATA_UPDATED after + unmarking the disk as SpareLocal + 9. If not (get "no-new-dev" lock), it fails the operation and sends + METADATA_UPDATED. + 10. Other nodes get the information whether a disk is added or not + by the following METADATA_UPDATED. + +6. Module interface. + + There are 17 call-backs which the md core can make to the cluster + module. Understanding these can give a good overview of the whole + process. + +6.1 join(nodes) and leave() + + These are called when an array is started with a clustered bitmap, + and when the array is stopped. join() ensures the cluster is + available and initializes the various resources. + Only the first 'nodes' nodes in the cluster can use the array. + +6.2 slot_number() + + Reports the slot number advised by the cluster infrastructure. + Range is from 0 to nodes-1. + +6.3 resync_info_update() + + This updates the resync range that is stored in the bitmap lock. + The starting point is updated as the resync progresses. The + end point is always the end of the array. + It does *not* send a RESYNCING message. + +6.4 resync_start(), resync_finish() + + These are called when resync/recovery/reshape starts or stops. + They update the resyncing range in the bitmap lock and also + send a RESYNCING message. resync_start reports the whole + array as resyncing, resync_finish reports none of it. + + resync_finish() also sends a BITMAP_NEEDS_SYNC message which + allows some other node to take over. + +6.5 metadata_update_start(), metadata_update_finish(), + metadata_update_cancel(). + + metadata_update_start is used to get exclusive access to + the metadata. If a change is still needed once that access is + gained, metadata_update_finish() will send a METADATA_UPDATE + message to all other nodes, otherwise metadata_update_cancel() + can be used to release the lock. + +6.6 area_resyncing() + + This combines two elements of functionality. + + Firstly, it will check if any node is currently resyncing + anything in a given range of sectors. If any resync is found, + then the caller will avoid writing or read-balancing in that + range. + + Secondly, while node recovery is happening it reports that + all areas are resyncing for READ requests. This avoids races + between the cluster-filesystem and the cluster-RAID handling + a node failure. + +6.7 add_new_disk_start(), add_new_disk_finish(), new_disk_ack() + + These are used to manage the new-disk protocol described above. + When a new device is added, add_new_disk_start() is called before + it is bound to the array and, if that succeeds, add_new_disk_finish() + is called the device is fully added. + + When a device is added in acknowledgement to a previous + request, or when the device is declared "unavailable", + new_disk_ack() is called. + +6.8 remove_disk() + + This is called when a spare or failed device is removed from + the array. It causes a REMOVE message to be send to other nodes. + +6.9 gather_bitmaps() + + This sends a RE_ADD message to all other nodes and then + gathers bitmap information from all bitmaps. This combined + bitmap is then used to recovery the re-added device. + +6.10 lock_all_bitmaps() and unlock_all_bitmaps() + + These are called when change bitmap to none. If a node plans + to clear the cluster raid's bitmap, it need to make sure no other + nodes are using the raid which is achieved by lock all bitmap + locks within the cluster, and also those locks are unlocked + accordingly. diff --git a/Documentation/media-framework.txt b/Documentation/media-framework.txt deleted file mode 100644 index f552a75c0e70..000000000000 --- a/Documentation/media-framework.txt +++ /dev/null @@ -1,372 +0,0 @@ -Linux kernel media framework -============================ - -This document describes the Linux kernel media framework, its data structures, -functions and their usage. - - -Introduction ------------- - -The media controller API is documented in DocBook format in -Documentation/DocBook/media/v4l/media-controller.xml. This document will focus -on the kernel-side implementation of the media framework. - - -Abstract media device model ---------------------------- - -Discovering a device internal topology, and configuring it at runtime, is one -of the goals of the media framework. To achieve this, hardware devices are -modelled as an oriented graph of building blocks called entities connected -through pads. - -An entity is a basic media hardware building block. It can correspond to -a large variety of logical blocks such as physical hardware devices -(CMOS sensor for instance), logical hardware devices (a building block -in a System-on-Chip image processing pipeline), DMA channels or physical -connectors. - -A pad is a connection endpoint through which an entity can interact with -other entities. Data (not restricted to video) produced by an entity -flows from the entity's output to one or more entity inputs. Pads should -not be confused with physical pins at chip boundaries. - -A link is a point-to-point oriented connection between two pads, either -on the same entity or on different entities. Data flows from a source -pad to a sink pad. - - -Media device ------------- - -A media device is represented by a struct media_device instance, defined in -include/media/media-device.h. Allocation of the structure is handled by the -media device driver, usually by embedding the media_device instance in a -larger driver-specific structure. - -Drivers register media device instances by calling - - media_device_register(struct media_device *mdev); - -The caller is responsible for initializing the media_device structure before -registration. The following fields must be set: - - - dev must point to the parent device (usually a pci_dev, usb_interface or - platform_device instance). - - - model must be filled with the device model name as a NUL-terminated UTF-8 - string. The device/model revision must not be stored in this field. - -The following fields are optional: - - - serial is a unique serial number stored as a NUL-terminated ASCII string. - The field is big enough to store a GUID in text form. If the hardware - doesn't provide a unique serial number this field must be left empty. - - - bus_info represents the location of the device in the system as a - NUL-terminated ASCII string. For PCI/PCIe devices bus_info must be set to - "PCI:" (or "PCIe:") followed by the value of pci_name(). For USB devices, - the usb_make_path() function must be used. This field is used by - applications to distinguish between otherwise identical devices that don't - provide a serial number. - - - hw_revision is the hardware device revision in a driver-specific format. - When possible the revision should be formatted with the KERNEL_VERSION - macro. - - - driver_version is formatted with the KERNEL_VERSION macro. The version - minor must be incremented when new features are added to the userspace API - without breaking binary compatibility. The version major must be - incremented when binary compatibility is broken. - -Upon successful registration a character device named media[0-9]+ is created. -The device major and minor numbers are dynamic. The model name is exported as -a sysfs attribute. - -Drivers unregister media device instances by calling - - media_device_unregister(struct media_device *mdev); - -Unregistering a media device that hasn't been registered is *NOT* safe. - - -Entities, pads and links ------------------------- - -- Entities - -Entities are represented by a struct media_entity instance, defined in -include/media/media-entity.h. The structure is usually embedded into a -higher-level structure, such as a v4l2_subdev or video_device instance, -although drivers can allocate entities directly. - -Drivers initialize entities by calling - - media_entity_init(struct media_entity *entity, u16 num_pads, - struct media_pad *pads, u16 extra_links); - -The media_entity name, type, flags, revision and group_id fields can be -initialized before or after calling media_entity_init. Entities embedded in -higher-level standard structures can have some of those fields set by the -higher-level framework. - -As the number of pads is known in advance, the pads array is not allocated -dynamically but is managed by the entity driver. Most drivers will embed the -pads array in a driver-specific structure, avoiding dynamic allocation. - -Drivers must set the direction of every pad in the pads array before calling -media_entity_init. The function will initialize the other pads fields. - -Unlike the number of pads, the total number of links isn't always known in -advance by the entity driver. As an initial estimate, media_entity_init -pre-allocates a number of links equal to the number of pads plus an optional -number of extra links. The links array will be reallocated if it grows beyond -the initial estimate. - -Drivers register entities with a media device by calling - - media_device_register_entity(struct media_device *mdev, - struct media_entity *entity); - -Entities are identified by a unique positive integer ID. Drivers can provide an -ID by filling the media_entity id field prior to registration, or request the -media controller framework to assign an ID automatically. Drivers that provide -IDs manually must ensure that all IDs are unique. IDs are not guaranteed to be -contiguous even when they are all assigned automatically by the framework. - -Drivers unregister entities by calling - - media_device_unregister_entity(struct media_entity *entity); - -Unregistering an entity will not change the IDs of the other entities, and the -ID will never be reused for a newly registered entity. - -When a media device is unregistered, all its entities are unregistered -automatically. No manual entities unregistration is then required. - -Drivers free resources associated with an entity by calling - - media_entity_cleanup(struct media_entity *entity); - -This function must be called during the cleanup phase after unregistering the -entity. Note that the media_entity instance itself must be freed explicitly by -the driver if required. - -Entities have flags that describe the entity capabilities and state. - - MEDIA_ENT_FL_DEFAULT indicates the default entity for a given type. - This can be used to report the default audio and video devices or the - default camera sensor. - -Logical entity groups can be defined by setting the group ID of all member -entities to the same non-zero value. An entity group serves no purpose in the -kernel, but is reported to userspace during entities enumeration. The group_id -field belongs to the media device driver and must not by touched by entity -drivers. - -Media device drivers should define groups if several entities are logically -bound together. Example usages include reporting - - - ALSA, VBI and video nodes that carry the same media stream - - lens and flash controllers associated with a sensor - -- Pads - -Pads are represented by a struct media_pad instance, defined in -include/media/media-entity.h. Each entity stores its pads in a pads array -managed by the entity driver. Drivers usually embed the array in a -driver-specific structure. - -Pads are identified by their entity and their 0-based index in the pads array. -Both information are stored in the media_pad structure, making the media_pad -pointer the canonical way to store and pass link references. - -Pads have flags that describe the pad capabilities and state. - - MEDIA_PAD_FL_SINK indicates that the pad supports sinking data. - MEDIA_PAD_FL_SOURCE indicates that the pad supports sourcing data. - -One and only one of MEDIA_PAD_FL_SINK and MEDIA_PAD_FL_SOURCE must be set for -each pad. - -- Links - -Links are represented by a struct media_link instance, defined in -include/media/media-entity.h. Each entity stores all links originating at or -targeting any of its pads in a links array. A given link is thus stored -twice, once in the source entity and once in the target entity. The array is -pre-allocated and grows dynamically as needed. - -Drivers create links by calling - - media_entity_create_link(struct media_entity *source, u16 source_pad, - struct media_entity *sink, u16 sink_pad, - u32 flags); - -An entry in the link array of each entity is allocated and stores pointers -to source and sink pads. - -Links have flags that describe the link capabilities and state. - - MEDIA_LNK_FL_ENABLED indicates that the link is enabled and can be used - to transfer media data. When two or more links target a sink pad, only - one of them can be enabled at a time. - MEDIA_LNK_FL_IMMUTABLE indicates that the link enabled state can't be - modified at runtime. If MEDIA_LNK_FL_IMMUTABLE is set, then - MEDIA_LNK_FL_ENABLED must also be set since an immutable link is always - enabled. - - -Graph traversal ---------------- - -The media framework provides APIs to iterate over entities in a graph. - -To iterate over all entities belonging to a media device, drivers can use the -media_device_for_each_entity macro, defined in include/media/media-device.h. - - struct media_entity *entity; - - media_device_for_each_entity(entity, mdev) { - /* entity will point to each entity in turn */ - ... - } - -Drivers might also need to iterate over all entities in a graph that can be -reached only through enabled links starting at a given entity. The media -framework provides a depth-first graph traversal API for that purpose. - -Note that graphs with cycles (whether directed or undirected) are *NOT* -supported by the graph traversal API. To prevent infinite loops, the graph -traversal code limits the maximum depth to MEDIA_ENTITY_ENUM_MAX_DEPTH, -currently defined as 16. - -Drivers initiate a graph traversal by calling - - media_entity_graph_walk_start(struct media_entity_graph *graph, - struct media_entity *entity); - -The graph structure, provided by the caller, is initialized to start graph -traversal at the given entity. - -Drivers can then retrieve the next entity by calling - - media_entity_graph_walk_next(struct media_entity_graph *graph); - -When the graph traversal is complete the function will return NULL. - -Graph traversal can be interrupted at any moment. No cleanup function call is -required and the graph structure can be freed normally. - -Helper functions can be used to find a link between two given pads, or a pad -connected to another pad through an enabled link - - media_entity_find_link(struct media_pad *source, - struct media_pad *sink); - - media_entity_remote_pad(struct media_pad *pad); - -Refer to the kerneldoc documentation for more information. - - -Use count and power handling ----------------------------- - -Due to the wide differences between drivers regarding power management needs, -the media controller does not implement power management. However, the -media_entity structure includes a use_count field that media drivers can use to -track the number of users of every entity for power management needs. - -The use_count field is owned by media drivers and must not be touched by entity -drivers. Access to the field must be protected by the media device graph_mutex -lock. - - -Links setup ------------ - -Link properties can be modified at runtime by calling - - media_entity_setup_link(struct media_link *link, u32 flags); - -The flags argument contains the requested new link flags. - -The only configurable property is the ENABLED link flag to enable/disable a -link. Links marked with the IMMUTABLE link flag can not be enabled or disabled. - -When a link is enabled or disabled, the media framework calls the -link_setup operation for the two entities at the source and sink of the link, -in that order. If the second link_setup call fails, another link_setup call is -made on the first entity to restore the original link flags. - -Media device drivers can be notified of link setup operations by setting the -media_device::link_notify pointer to a callback function. If provided, the -notification callback will be called before enabling and after disabling -links. - -Entity drivers must implement the link_setup operation if any of their links -is non-immutable. The operation must either configure the hardware or store -the configuration information to be applied later. - -Link configuration must not have any side effect on other links. If an enabled -link at a sink pad prevents another link at the same pad from being enabled, -the link_setup operation must return -EBUSY and can't implicitly disable the -first enabled link. - - -Pipelines and media streams ---------------------------- - -When starting streaming, drivers must notify all entities in the pipeline to -prevent link states from being modified during streaming by calling - - media_entity_pipeline_start(struct media_entity *entity, - struct media_pipeline *pipe); - -The function will mark all entities connected to the given entity through -enabled links, either directly or indirectly, as streaming. - -The media_pipeline instance pointed to by the pipe argument will be stored in -every entity in the pipeline. Drivers should embed the media_pipeline structure -in higher-level pipeline structures and can then access the pipeline through -the media_entity pipe field. - -Calls to media_entity_pipeline_start() can be nested. The pipeline pointer must -be identical for all nested calls to the function. - -media_entity_pipeline_start() may return an error. In that case, it will -clean up any of the changes it did by itself. - -When stopping the stream, drivers must notify the entities with - - media_entity_pipeline_stop(struct media_entity *entity); - -If multiple calls to media_entity_pipeline_start() have been made the same -number of media_entity_pipeline_stop() calls are required to stop streaming. The -media_entity pipe field is reset to NULL on the last nested stop call. - -Link configuration will fail with -EBUSY by default if either end of the link is -a streaming entity. Links that can be modified while streaming must be marked -with the MEDIA_LNK_FL_DYNAMIC flag. - -If other operations need to be disallowed on streaming entities (such as -changing entities configuration parameters) drivers can explicitly check the -media_entity stream_count field to find out if an entity is streaming. This -operation must be done with the media_device graph_mutex held. - - -Link validation ---------------- - -Link validation is performed by media_entity_pipeline_start() for any -entity which has sink pads in the pipeline. The -media_entity::link_validate() callback is used for that purpose. In -link_validate() callback, entity driver should check that the properties of -the source pad of the connected entity and its own sink pad match. It is up -to the type of the entity (and in the end, the properties of the hardware) -what matching actually means. - -Subsystems should facilitate link validation by providing subsystem specific -helper functions to provide easy access for commonly needed information, and -in the end provide a way to use driver-specific callbacks. diff --git a/Documentation/mtd/nand_ecc.txt b/Documentation/mtd/nand_ecc.txt index e129b2479ea8..f8c3284bf6a7 100644 --- a/Documentation/mtd/nand_ecc.txt +++ b/Documentation/mtd/nand_ecc.txt @@ -107,7 +107,7 @@ for (i = 0; i < 256; i++) if (i & 0x01) rp1 = bit7 ^ bit6 ^ bit5 ^ bit4 ^ bit3 ^ bit2 ^ bit1 ^ bit0 ^ rp1; else - rp0 = bit7 ^ bit6 ^ bit5 ^ bit4 ^ bit3 ^ bit2 ^ bit1 ^ bit0 ^ rp1; + rp0 = bit7 ^ bit6 ^ bit5 ^ bit4 ^ bit3 ^ bit2 ^ bit1 ^ bit0 ^ rp0; if (i & 0x02) rp3 = bit7 ^ bit6 ^ bit5 ^ bit4 ^ bit3 ^ bit2 ^ bit1 ^ bit0 ^ rp3; else @@ -127,7 +127,7 @@ for (i = 0; i < 256; i++) if (i & 0x20) rp11 = bit7 ^ bit6 ^ bit5 ^ bit4 ^ bit3 ^ bit2 ^ bit1 ^ bit0 ^ rp11; else - rp10 = bit7 ^ bit6 ^ bit5 ^ bit4 ^ bit3 ^ bit2 ^ bit1 ^ bit0 ^ rp10; + rp10 = bit7 ^ bit6 ^ bit5 ^ bit4 ^ bit3 ^ bit2 ^ bit1 ^ bit0 ^ rp10; if (i & 0x40) rp13 = bit7 ^ bit6 ^ bit5 ^ bit4 ^ bit3 ^ bit2 ^ bit1 ^ bit0 ^ rp13; else @@ -158,7 +158,7 @@ the values in any order. So instead of calculating all the bits individually, let us try to rearrange things. For the column parity this is easy. We can just xor the bytes and in the end filter out the relevant bits. This is pretty nice as it will bring -all cp calculation out of the if loop. +all cp calculation out of the for loop. Similarly we can first xor the bytes for the various rows. This leads to: @@ -271,11 +271,11 @@ to write our code in such a way that we process data in 32 bit chunks. Of course this means some modification as the row parity is byte by byte. A quick analysis: for the column parity we use the par variable. When extending to 32 bits -we can in the end easily calculate p0 and p1 from it. +we can in the end easily calculate rp0 and rp1 from it. (because par now consists of 4 bytes, contributing to rp1, rp0, rp1, rp0 -respectively) +respectively, from MSB to LSB) also rp2 and rp3 can be easily retrieved from par as rp3 covers the -first two bytes and rp2 the last two bytes. +first two MSBs and rp2 covers the last two LSBs. Note that of course now the loop is executed only 64 times (256/4). And note that care must taken wrt byte ordering. The way bytes are @@ -387,11 +387,11 @@ Analysis 2 The code (of course) works, and hurray: we are a little bit faster than the linux driver code (about 15%). But wait, don't cheer too quickly. -THere is more to be gained. +There is more to be gained. If we look at e.g. rp14 and rp15 we see that we either xor our data with rp14 or with rp15. However we also have par which goes over all data. This means there is no need to calculate rp14 as it can be calculated from -rp15 through rp14 = par ^ rp15; +rp15 through rp14 = par ^ rp15, because par = rp14 ^ rp15; (or if desired we can avoid calculating rp15 and calculate it from rp14). That is why some places refer to inverse parity. Of course the same thing holds for rp4/5, rp6/7, rp8/9, rp10/11 and rp12/13. @@ -419,12 +419,12 @@ with if (i & 0x20) rp15 ^= cur; and outside the loop added: - rp4 = par ^ rp5; - rp6 = par ^ rp7; - rp8 = par ^ rp9; - rp10 = par ^ rp11; - rp12 = par ^ rp13; - rp14 = par ^ rp15; + rp4 = par ^ rp5; + rp6 = par ^ rp7; + rp8 = par ^ rp9; + rp10 = par ^ rp11; + rp12 = par ^ rp13; + rp14 = par ^ rp15; And after that the code takes about 30% more time, although the number of statements is reduced. This is also reflected in the assembly code. @@ -524,12 +524,12 @@ THe code within the for loop was changed to: cur = *bp++; tmppar ^= cur; rp4 ^= cur; rp6 ^= cur; cur = *bp++; tmppar ^= cur; rp6 ^= cur; - cur = *bp++; tmppar ^= cur; rp4 ^= cur; - cur = *bp++; tmppar ^= cur; rp10 ^= tmppar; + cur = *bp++; tmppar ^= cur; rp4 ^= cur; + cur = *bp++; tmppar ^= cur; rp10 ^= tmppar; - cur = *bp++; tmppar ^= cur; rp4 ^= cur; rp6 ^= cur; rp8 ^= cur; + cur = *bp++; tmppar ^= cur; rp4 ^= cur; rp6 ^= cur; rp8 ^= cur; cur = *bp++; tmppar ^= cur; rp6 ^= cur; rp8 ^= cur; - cur = *bp++; tmppar ^= cur; rp4 ^= cur; rp8 ^= cur; + cur = *bp++; tmppar ^= cur; rp4 ^= cur; rp8 ^= cur; cur = *bp++; tmppar ^= cur; rp8 ^= cur; cur = *bp++; tmppar ^= cur; rp4 ^= cur; rp6 ^= cur; @@ -537,7 +537,7 @@ THe code within the for loop was changed to: cur = *bp++; tmppar ^= cur; rp4 ^= cur; cur = *bp++; tmppar ^= cur; - par ^= tmppar; + par ^= tmppar; if ((i & 0x1) == 0) rp12 ^= tmppar; if ((i & 0x2) == 0) rp14 ^= tmppar; } @@ -548,8 +548,8 @@ to rp12 and rp14. While making the changes I also found that I could exploit that tmppar contains the running parity for this iteration. So instead of having: -rp4 ^= cur; rp6 = cur; -I removed the rp6 = cur; statement and did rp6 ^= tmppar; on next +rp4 ^= cur; rp6 ^= cur; +I removed the rp6 ^= cur; statement and did rp6 ^= tmppar; on next statement. A similar change was done for rp8 and rp10 @@ -593,22 +593,22 @@ The new code now looks like: cur = *bp++; tmppar ^= cur; rp4_6 ^= cur; cur = *bp++; tmppar ^= cur; rp6 ^= cur; - cur = *bp++; tmppar ^= cur; rp4 ^= cur; - cur = *bp++; tmppar ^= cur; rp10 ^= tmppar; + cur = *bp++; tmppar ^= cur; rp4 ^= cur; + cur = *bp++; tmppar ^= cur; rp10 ^= tmppar; - notrp8 = tmppar; - cur = *bp++; tmppar ^= cur; rp4_6 ^= cur; + notrp8 = tmppar; + cur = *bp++; tmppar ^= cur; rp4_6 ^= cur; cur = *bp++; tmppar ^= cur; rp6 ^= cur; - cur = *bp++; tmppar ^= cur; rp4 ^= cur; + cur = *bp++; tmppar ^= cur; rp4 ^= cur; cur = *bp++; tmppar ^= cur; - rp8 = rp8 ^ tmppar ^ notrp8; + rp8 = rp8 ^ tmppar ^ notrp8; cur = *bp++; tmppar ^= cur; rp4_6 ^= cur; cur = *bp++; tmppar ^= cur; rp6 ^= cur; cur = *bp++; tmppar ^= cur; rp4 ^= cur; cur = *bp++; tmppar ^= cur; - par ^= tmppar; + par ^= tmppar; if ((i & 0x1) == 0) rp12 ^= tmppar; if ((i & 0x2) == 0) rp14 ^= tmppar; } @@ -700,7 +700,7 @@ Conclusion The gain when calculating the ecc is tremendous. Om my development hardware a speedup of a factor of 18 for ecc calculation was achieved. On a test on an embedded system with a MIPS core a factor 7 was obtained. -On a test with a Linksys NSLU2 (ARMv5TE processor) the speedup was a factor +On a test with a Linksys NSLU2 (ARMv5TE processor) the speedup was a factor 5 (big endian mode, gcc 4.1.2, -O3) For correction not much gain could be obtained (as bitflips are rare). Then again there are also much less cycles spent there. diff --git a/Documentation/s390/zfcpdump.txt b/Documentation/s390/zfcpdump.txt index dc929be96016..b064aa59714d 100644 --- a/Documentation/s390/zfcpdump.txt +++ b/Documentation/s390/zfcpdump.txt @@ -15,19 +15,15 @@ the s390-tools package) to make the device bootable. The operator of a Linux system can then trigger a SCSI dump by booting the SCSI disk, where zfcpdump resides on. -The kernel part of zfcpdump is implemented as a debugfs file under "zcore/mem", -which exports memory and registers of the crashed Linux in an s390 -standalone dump format. It can be used in the same way as e.g. /dev/mem. The -dump format defines a 4K header followed by plain uncompressed memory. The -register sets are stored in the prefix pages of the respective CPUs. To build a -dump enabled kernel with the zcore driver, the kernel config option -CONFIG_CRASH_DUMP has to be set. When reading from "zcore/mem", the part of -memory, which has been saved by hardware is read by the driver via the SCLP -hardware interface. The second part is just copied from the non overwritten real -memory. - -Since kernel version 3.12 also the /proc/vmcore file can also be used to access -the dump. +The user space dump tool accesses the memory of the crashed system by means +of the /proc/vmcore interface. This interface exports the crashed system's +memory and registers in ELF core dump format. To access the memory which has +been saved by the hardware SCLP requests will be created at the time the data +is needed by /proc/vmcore. The tail part of the crashed systems memory which +has not been stashed by hardware can just be copied from real memory. + +To build a dump enabled kernel the kernel config option CONFIG_CRASH_DUMP +has to be set. To get a valid zfcpdump kernel configuration use "make zfcpdump_defconfig". diff --git a/Documentation/spi/.gitignore b/Documentation/spi/.gitignore deleted file mode 100644 index 4280576397e8..000000000000 --- a/Documentation/spi/.gitignore +++ /dev/null @@ -1,2 +0,0 @@ -spidev_fdx -spidev_test diff --git a/Documentation/spi/00-INDEX b/Documentation/spi/00-INDEX index a128fa835512..4644bf0d9832 100644 --- a/Documentation/spi/00-INDEX +++ b/Documentation/spi/00-INDEX @@ -10,13 +10,9 @@ pxa2xx - PXA2xx SPI master controller build by spi_message fifo wq spidev - Intro to the userspace API for spi devices -spidev_fdx.c - - spidev example file spi-lm70llp - Connecting an LM70-LLP sensor to the kernel via the SPI subsys. spi-sc18is602 - NXP SC18IS602/603 I2C-bus to SPI bridge spi-summary - (Linux) SPI overview. If unsure about SPI or SPI in Linux, start here. -spidev_test.c - - SPI testing utility. diff --git a/Documentation/spi/Makefile b/Documentation/spi/Makefile deleted file mode 100644 index efa255813e9d..000000000000 --- a/Documentation/spi/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# List of programs to build -hostprogs-y := spidev_test spidev_fdx - -# Tell kbuild to always build the programs -always := $(hostprogs-y) - -HOSTCFLAGS_spidev_test.o += -I$(objtree)/usr/include -HOSTCFLAGS_spidev_fdx.o += -I$(objtree)/usr/include diff --git a/Documentation/spi/spidev_fdx.c b/Documentation/spi/spidev_fdx.c deleted file mode 100644 index 0ea3e51292fc..000000000000 --- a/Documentation/spi/spidev_fdx.c +++ /dev/null @@ -1,158 +0,0 @@ -#include <stdio.h> -#include <unistd.h> -#include <stdlib.h> -#include <fcntl.h> -#include <string.h> - -#include <sys/ioctl.h> -#include <sys/types.h> -#include <sys/stat.h> - -#include <linux/types.h> -#include <linux/spi/spidev.h> - - -static int verbose; - -static void do_read(int fd, int len) -{ - unsigned char buf[32], *bp; - int status; - - /* read at least 2 bytes, no more than 32 */ - if (len < 2) - len = 2; - else if (len > sizeof(buf)) - len = sizeof(buf); - memset(buf, 0, sizeof buf); - - status = read(fd, buf, len); - if (status < 0) { - perror("read"); - return; - } - if (status != len) { - fprintf(stderr, "short read\n"); - return; - } - - printf("read(%2d, %2d): %02x %02x,", len, status, - buf[0], buf[1]); - status -= 2; - bp = buf + 2; - while (status-- > 0) - printf(" %02x", *bp++); - printf("\n"); -} - -static void do_msg(int fd, int len) -{ - struct spi_ioc_transfer xfer[2]; - unsigned char buf[32], *bp; - int status; - - memset(xfer, 0, sizeof xfer); - memset(buf, 0, sizeof buf); - - if (len > sizeof buf) - len = sizeof buf; - - buf[0] = 0xaa; - xfer[0].tx_buf = (unsigned long)buf; - xfer[0].len = 1; - - xfer[1].rx_buf = (unsigned long) buf; - xfer[1].len = len; - - status = ioctl(fd, SPI_IOC_MESSAGE(2), xfer); - if (status < 0) { - perror("SPI_IOC_MESSAGE"); - return; - } - - printf("response(%2d, %2d): ", len, status); - for (bp = buf; len; len--) - printf(" %02x", *bp++); - printf("\n"); -} - -static void dumpstat(const char *name, int fd) -{ - __u8 lsb, bits; - __u32 mode, speed; - - if (ioctl(fd, SPI_IOC_RD_MODE32, &mode) < 0) { - perror("SPI rd_mode"); - return; - } - if (ioctl(fd, SPI_IOC_RD_LSB_FIRST, &lsb) < 0) { - perror("SPI rd_lsb_fist"); - return; - } - if (ioctl(fd, SPI_IOC_RD_BITS_PER_WORD, &bits) < 0) { - perror("SPI bits_per_word"); - return; - } - if (ioctl(fd, SPI_IOC_RD_MAX_SPEED_HZ, &speed) < 0) { - perror("SPI max_speed_hz"); - return; - } - - printf("%s: spi mode 0x%x, %d bits %sper word, %d Hz max\n", - name, mode, bits, lsb ? "(lsb first) " : "", speed); -} - -int main(int argc, char **argv) -{ - int c; - int readcount = 0; - int msglen = 0; - int fd; - const char *name; - - while ((c = getopt(argc, argv, "hm:r:v")) != EOF) { - switch (c) { - case 'm': - msglen = atoi(optarg); - if (msglen < 0) - goto usage; - continue; - case 'r': - readcount = atoi(optarg); - if (readcount < 0) - goto usage; - continue; - case 'v': - verbose++; - continue; - case 'h': - case '?': -usage: - fprintf(stderr, - "usage: %s [-h] [-m N] [-r N] /dev/spidevB.D\n", - argv[0]); - return 1; - } - } - - if ((optind + 1) != argc) - goto usage; - name = argv[optind]; - - fd = open(name, O_RDWR); - if (fd < 0) { - perror("open"); - return 1; - } - - dumpstat(name, fd); - - if (msglen) - do_msg(fd, msglen); - - if (readcount) - do_read(fd, readcount); - - close(fd); - return 0; -} diff --git a/Documentation/spi/spidev_test.c b/Documentation/spi/spidev_test.c deleted file mode 100644 index 135b3f592b83..000000000000 --- a/Documentation/spi/spidev_test.c +++ /dev/null @@ -1,318 +0,0 @@ -/* - * SPI testing utility (using spidev driver) - * - * Copyright (c) 2007 MontaVista Software, Inc. - * Copyright (c) 2007 Anton Vorontsov <avorontsov@ru.mvista.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License. - * - * Cross-compile with cross-gcc -I/path/to/cross-kernel/include - */ - -#include <stdint.h> -#include <unistd.h> -#include <stdio.h> -#include <stdlib.h> -#include <string.h> -#include <getopt.h> -#include <fcntl.h> -#include <sys/ioctl.h> -#include <linux/types.h> -#include <linux/spi/spidev.h> - -#define ARRAY_SIZE(a) (sizeof(a) / sizeof((a)[0])) - -static void pabort(const char *s) -{ - perror(s); - abort(); -} - -static const char *device = "/dev/spidev1.1"; -static uint32_t mode; -static uint8_t bits = 8; -static uint32_t speed = 500000; -static uint16_t delay; -static int verbose; - -uint8_t default_tx[] = { - 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, - 0x40, 0x00, 0x00, 0x00, 0x00, 0x95, - 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, - 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, - 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, - 0xF0, 0x0D, -}; - -uint8_t default_rx[ARRAY_SIZE(default_tx)] = {0, }; -char *input_tx; - -static void hex_dump(const void *src, size_t length, size_t line_size, char *prefix) -{ - int i = 0; - const unsigned char *address = src; - const unsigned char *line = address; - unsigned char c; - - printf("%s | ", prefix); - while (length-- > 0) { - printf("%02X ", *address++); - if (!(++i % line_size) || (length == 0 && i % line_size)) { - if (length == 0) { - while (i++ % line_size) - printf("__ "); - } - printf(" | "); /* right close */ - while (line < address) { - c = *line++; - printf("%c", (c < 33 || c == 255) ? 0x2E : c); - } - printf("\n"); - if (length > 0) - printf("%s | ", prefix); - } - } -} - -/* - * Unescape - process hexadecimal escape character - * converts shell input "\x23" -> 0x23 - */ -static int unescape(char *_dst, char *_src, size_t len) -{ - int ret = 0; - char *src = _src; - char *dst = _dst; - unsigned int ch; - - while (*src) { - if (*src == '\\' && *(src+1) == 'x') { - sscanf(src + 2, "%2x", &ch); - src += 4; - *dst++ = (unsigned char)ch; - } else { - *dst++ = *src++; - } - ret++; - } - return ret; -} - -static void transfer(int fd, uint8_t const *tx, uint8_t const *rx, size_t len) -{ - int ret; - - struct spi_ioc_transfer tr = { - .tx_buf = (unsigned long)tx, - .rx_buf = (unsigned long)rx, - .len = len, - .delay_usecs = delay, - .speed_hz = speed, - .bits_per_word = bits, - }; - - if (mode & SPI_TX_QUAD) - tr.tx_nbits = 4; - else if (mode & SPI_TX_DUAL) - tr.tx_nbits = 2; - if (mode & SPI_RX_QUAD) - tr.rx_nbits = 4; - else if (mode & SPI_RX_DUAL) - tr.rx_nbits = 2; - if (!(mode & SPI_LOOP)) { - if (mode & (SPI_TX_QUAD | SPI_TX_DUAL)) - tr.rx_buf = 0; - else if (mode & (SPI_RX_QUAD | SPI_RX_DUAL)) - tr.tx_buf = 0; - } - - ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr); - if (ret < 1) - pabort("can't send spi message"); - - if (verbose) - hex_dump(tx, len, 32, "TX"); - hex_dump(rx, len, 32, "RX"); -} - -static void print_usage(const char *prog) -{ - printf("Usage: %s [-DsbdlHOLC3]\n", prog); - puts(" -D --device device to use (default /dev/spidev1.1)\n" - " -s --speed max speed (Hz)\n" - " -d --delay delay (usec)\n" - " -b --bpw bits per word \n" - " -l --loop loopback\n" - " -H --cpha clock phase\n" - " -O --cpol clock polarity\n" - " -L --lsb least significant bit first\n" - " -C --cs-high chip select active high\n" - " -3 --3wire SI/SO signals shared\n" - " -v --verbose Verbose (show tx buffer)\n" - " -p Send data (e.g. \"1234\\xde\\xad\")\n" - " -N --no-cs no chip select\n" - " -R --ready slave pulls low to pause\n" - " -2 --dual dual transfer\n" - " -4 --quad quad transfer\n"); - exit(1); -} - -static void parse_opts(int argc, char *argv[]) -{ - while (1) { - static const struct option lopts[] = { - { "device", 1, 0, 'D' }, - { "speed", 1, 0, 's' }, - { "delay", 1, 0, 'd' }, - { "bpw", 1, 0, 'b' }, - { "loop", 0, 0, 'l' }, - { "cpha", 0, 0, 'H' }, - { "cpol", 0, 0, 'O' }, - { "lsb", 0, 0, 'L' }, - { "cs-high", 0, 0, 'C' }, - { "3wire", 0, 0, '3' }, - { "no-cs", 0, 0, 'N' }, - { "ready", 0, 0, 'R' }, - { "dual", 0, 0, '2' }, - { "verbose", 0, 0, 'v' }, - { "quad", 0, 0, '4' }, - { NULL, 0, 0, 0 }, - }; - int c; - - c = getopt_long(argc, argv, "D:s:d:b:lHOLC3NR24p:v", lopts, NULL); - - if (c == -1) - break; - - switch (c) { - case 'D': - device = optarg; - break; - case 's': - speed = atoi(optarg); - break; - case 'd': - delay = atoi(optarg); - break; - case 'b': - bits = atoi(optarg); - break; - case 'l': - mode |= SPI_LOOP; - break; - case 'H': - mode |= SPI_CPHA; - break; - case 'O': - mode |= SPI_CPOL; - break; - case 'L': - mode |= SPI_LSB_FIRST; - break; - case 'C': - mode |= SPI_CS_HIGH; - break; - case '3': - mode |= SPI_3WIRE; - break; - case 'N': - mode |= SPI_NO_CS; - break; - case 'v': - verbose = 1; - break; - case 'R': - mode |= SPI_READY; - break; - case 'p': - input_tx = optarg; - break; - case '2': - mode |= SPI_TX_DUAL; - break; - case '4': - mode |= SPI_TX_QUAD; - break; - default: - print_usage(argv[0]); - break; - } - } - if (mode & SPI_LOOP) { - if (mode & SPI_TX_DUAL) - mode |= SPI_RX_DUAL; - if (mode & SPI_TX_QUAD) - mode |= SPI_RX_QUAD; - } -} - -int main(int argc, char *argv[]) -{ - int ret = 0; - int fd; - uint8_t *tx; - uint8_t *rx; - int size; - - parse_opts(argc, argv); - - fd = open(device, O_RDWR); - if (fd < 0) - pabort("can't open device"); - - /* - * spi mode - */ - ret = ioctl(fd, SPI_IOC_WR_MODE32, &mode); - if (ret == -1) - pabort("can't set spi mode"); - - ret = ioctl(fd, SPI_IOC_RD_MODE32, &mode); - if (ret == -1) - pabort("can't get spi mode"); - - /* - * bits per word - */ - ret = ioctl(fd, SPI_IOC_WR_BITS_PER_WORD, &bits); - if (ret == -1) - pabort("can't set bits per word"); - - ret = ioctl(fd, SPI_IOC_RD_BITS_PER_WORD, &bits); - if (ret == -1) - pabort("can't get bits per word"); - - /* - * max speed hz - */ - ret = ioctl(fd, SPI_IOC_WR_MAX_SPEED_HZ, &speed); - if (ret == -1) - pabort("can't set max speed hz"); - - ret = ioctl(fd, SPI_IOC_RD_MAX_SPEED_HZ, &speed); - if (ret == -1) - pabort("can't get max speed hz"); - - printf("spi mode: 0x%x\n", mode); - printf("bits per word: %d\n", bits); - printf("max speed: %d Hz (%d KHz)\n", speed, speed/1000); - - if (input_tx) { - size = strlen(input_tx+1); - tx = malloc(size); - rx = malloc(size); - size = unescape((char *)tx, input_tx, size); - transfer(fd, tx, rx, size); - free(rx); - free(tx); - } else { - transfer(fd, default_tx, default_rx, sizeof(default_tx)); - } - - close(fd); - - return ret; -} diff --git a/Documentation/sysctl/vm.txt b/Documentation/sysctl/vm.txt index f72370b440b1..89a887c76629 100644 --- a/Documentation/sysctl/vm.txt +++ b/Documentation/sysctl/vm.txt @@ -42,6 +42,8 @@ Currently, these files are in /proc/sys/vm: - min_slab_ratio - min_unmapped_ratio - mmap_min_addr +- mmap_rnd_bits +- mmap_rnd_compat_bits - nr_hugepages - nr_overcommit_hugepages - nr_trim_pages (only if CONFIG_MMU=n) @@ -135,7 +137,7 @@ Contains, as a percentage of total available memory that contains free pages and reclaimable pages, the number of pages at which the background kernel flusher threads will start writing out dirty data. -The total avaiable memory is not equal to total system memory. +The total available memory is not equal to total system memory. ============================================================== @@ -170,7 +172,7 @@ Contains, as a percentage of total available memory that contains free pages and reclaimable pages, the number of pages at which a process which is generating disk writes will itself start writing out dirty data. -The total avaiable memory is not equal to total system memory. +The total available memory is not equal to total system memory. ============================================================== @@ -485,6 +487,33 @@ against future potential kernel bugs. ============================================================== +mmap_rnd_bits: + +This value can be used to select the number of bits to use to +determine the random offset to the base address of vma regions +resulting from mmap allocations on architectures which support +tuning address space randomization. This value will be bounded +by the architecture's minimum and maximum supported values. + +This value can be changed after boot using the +/proc/sys/vm/mmap_rnd_bits tunable + +============================================================== + +mmap_rnd_compat_bits: + +This value can be used to select the number of bits to use to +determine the random offset to the base address of vma regions +resulting from mmap allocations for applications run in +compatibility mode on architectures which support tuning address +space randomization. This value will be bounded by the +architecture's minimum and maximum supported values. + +This value can be changed after boot using the +/proc/sys/vm/mmap_rnd_compat_bits tunable + +============================================================== + nr_hugepages Change the minimum size of the hugepage pool. diff --git a/Documentation/usb/chipidea.txt b/Documentation/usb/chipidea.txt index 3f848c1f2940..05f735a1b5a5 100644 --- a/Documentation/usb/chipidea.txt +++ b/Documentation/usb/chipidea.txt @@ -7,8 +7,8 @@ with 2 Freescale i.MX6Q sabre SD boards. --------------------------------------- Select CONFIG_USB_OTG_FSM, rebuild kernel Image and modules. If you want to check some internal variables for otg fsm, -select CONFIG_USB_CHIPIDEA_DEBUG, there are 2 files which -can show otg fsm variables and some controller registers value: +mount debugfs, there are 2 files which can show otg fsm +variables and some controller registers value: cat /sys/kernel/debug/ci_hdrc.0/otg cat /sys/kernel/debug/ci_hdrc.0/registers diff --git a/Documentation/usb/gadget-testing.txt b/Documentation/usb/gadget-testing.txt index b24d3ef89166..581960574889 100644 --- a/Documentation/usb/gadget-testing.txt +++ b/Documentation/usb/gadget-testing.txt @@ -434,7 +434,7 @@ On host: serialc -v <vendorID> -p <productID> -i<interface#> -a1 -s1024 \ where seriald and serialc are Felipe's utilities found here: -https://git.gitorious.org/usb/usb-tools.git master +https://github.com/felipebalbi/usb-tools.git master 12. PHONET function =================== @@ -579,6 +579,8 @@ The SOURCESINK function provides these attributes in its function directory: isoc_mult - 0..2 (hs/ss only) isoc_maxburst - 0..15 (ss only) bulk_buflen - buffer length + bulk_qlen - depth of queue for bulk + iso_qlen - depth of queue for iso Testing the SOURCESINK function ------------------------------- diff --git a/Documentation/usb/power-management.txt b/Documentation/usb/power-management.txt index 4a15c90bc11d..0a94ffe17ab6 100644 --- a/Documentation/usb/power-management.txt +++ b/Documentation/usb/power-management.txt @@ -537,17 +537,18 @@ relevant attribute files are usb2_hardware_lpm and usb3_hardware_lpm. can write y/Y/1 or n/N/0 to the file to enable/disable USB2 hardware LPM manually. This is for test purpose mainly. - power/usb3_hardware_lpm + power/usb3_hardware_lpm_u1 + power/usb3_hardware_lpm_u2 When a USB 3.0 lpm-capable device is plugged in to a xHCI host which supports link PM, it will check if U1 and U2 exit latencies have been set in the BOS descriptor; if the check is is passed and the host supports USB3 hardware LPM, USB3 hardware LPM will be - enabled for the device and this file will be created. - The file holds a string value (enable or disable) - indicating whether or not USB3 hardware LPM is - enabled for the device. + enabled for the device and these files will be created. + The files hold a string value (enable or disable) + indicating whether or not USB3 hardware LPM U1 or U2 + is enabled for the device. USB Port Power Control ---------------------- diff --git a/Documentation/video4linux/v4l2-framework.txt b/Documentation/video4linux/v4l2-framework.txt index 75d5c18d689a..fa41608ab2b4 100644 --- a/Documentation/video4linux/v4l2-framework.txt +++ b/Documentation/video4linux/v4l2-framework.txt @@ -295,16 +295,16 @@ module owner. This is done for you if you use the i2c helper functions. If integration with the media framework is needed, you must initialize the media_entity struct embedded in the v4l2_subdev struct (entity field) by -calling media_entity_init(): +calling media_entity_pads_init(), if the entity has pads: struct media_pad *pads = &my_sd->pads; int err; - err = media_entity_init(&sd->entity, npads, pads, 0); + err = media_entity_pads_init(&sd->entity, npads, pads); The pads array must have been previously initialized. There is no need to -manually set the struct media_entity type and name fields, but the revision -field must be initialized if needed. +manually set the struct media_entity function and name fields, but the +revision field must be initialized if needed. A reference to the entity will be automatically acquired/released when the subdev device node (if any) is opened/closed. @@ -695,12 +695,12 @@ difference is that the inode argument is omitted since it is never used. If integration with the media framework is needed, you must initialize the media_entity struct embedded in the video_device struct (entity field) by -calling media_entity_init(): +calling media_entity_pads_init(): struct media_pad *pad = &my_vdev->pad; int err; - err = media_entity_init(&vdev->entity, 1, pad, 0); + err = media_entity_pads_init(&vdev->entity, 1, pad); The pads array must have been previously initialized. There is no need to manually set the struct media_entity type and name fields. diff --git a/Documentation/zh_CN/video4linux/v4l2-framework.txt b/Documentation/zh_CN/video4linux/v4l2-framework.txt index 2b828e631e31..698660b7f21f 100644 --- a/Documentation/zh_CN/video4linux/v4l2-framework.txt +++ b/Documentation/zh_CN/video4linux/v4l2-framework.txt @@ -289,13 +289,13 @@ struct v4l2_subdev_ops { 然后，你必须用一个唯一的名字初始化 subdev->name，并初始化模块的 owner 域。若使用 i2c 辅助函数，这些都会帮你处理好。 -若需同媒体框架整合，你必须调用 media_entity_init() 初始化 v4l2_subdev +若需同媒体框架整合，你必须调用 media_entity_pads_init() 初始化 v4l2_subdev 结构体中的 media_entity 结构体（entity 域）： struct media_pad *pads = &my_sd->pads; int err; - err = media_entity_init(&sd->entity, npads, pads, 0); + err = media_entity_pads_init(&sd->entity, npads, pads); pads 数组必须预先初始化。无须手动设置 media_entity 的 type 和 name 域，但如有必要，revision 域必须初始化。 @@ -596,13 +596,13 @@ void v4l2_disable_ioctl(struct video_device *vdev, unsigned int cmd); v4l2_file_operations 结构体是 file_operations 的一个子集。其主要 区别在于：因 inode 参数从未被使用，它将被忽略。 -如果需要与媒体框架整合，你必须通过调用 media_entity_init() 初始化 +如果需要与媒体框架整合，你必须通过调用 media_entity_pads_init() 初始化 嵌入在 video_device 结构体中的 media_entity（entity 域）结构体： struct media_pad *pad = &my_vdev->pad; int err; - err = media_entity_init(&vdev->entity, 1, pad, 0); + err = media_entity_pads_init(&vdev->entity, 1, pad); pads 数组必须预先初始化。没有必要手动设置 media_entity 的 type 和 name 域。 |