diff options
Diffstat (limited to 'arch/arm/boot/dts/armada-388-clearfog.dts')
-rw-r--r-- | arch/arm/boot/dts/armada-388-clearfog.dts | 378 |
1 files changed, 2 insertions, 376 deletions
diff --git a/arch/arm/boot/dts/armada-388-clearfog.dts b/arch/arm/boot/dts/armada-388-clearfog.dts index 9bf399dd1786..c5f2ca5f6144 100644 --- a/arch/arm/boot/dts/armada-388-clearfog.dts +++ b/arch/arm/boot/dts/armada-388-clearfog.dts @@ -1,5 +1,5 @@ /* - * Device Tree file for SolidRun Clearfog revision A1 rev 2.0 (88F6828) + * Device Tree file for SolidRun Clearfog Pro revision A1 rev 2.0 (88F6828) * * Copyright (C) 2015 Russell King * @@ -47,384 +47,10 @@ */ /dts-v1/; -#include "armada-388.dtsi" -#include "armada-38x-solidrun-microsom.dtsi" +#include "armada-388-clearfog.dtsi" / { model = "SolidRun Clearfog A1"; compatible = "solidrun,clearfog-a1", "marvell,armada388", "marvell,armada385", "marvell,armada380"; - - aliases { - /* So that mvebu u-boot can update the MAC addresses */ - ethernet1 = ð0; - ethernet2 = ð1; - ethernet3 = ð2; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - reg_3p3v: regulator-3p3v { - compatible = "regulator-fixed"; - regulator-name = "3P3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - soc { - internal-regs { - ethernet@30000 { - phy-mode = "sgmii"; - buffer-manager = <&bm>; - bm,pool-long = <2>; - bm,pool-short = <1>; - status = "okay"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - ethernet@34000 { - phy-mode = "sgmii"; - buffer-manager = <&bm>; - bm,pool-long = <3>; - bm,pool-short = <1>; - status = "okay"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - - i2c@11000 { - /* Is there anything on this? */ - clock-frequency = <100000>; - pinctrl-0 = <&i2c0_pins>; - pinctrl-names = "default"; - status = "okay"; - - /* - * PCA9655 GPIO expander, up to 1MHz clock. - * 0-CON3 CLKREQ# - * 1-CON3 PERST# - * 2-CON2 PERST# - * 3-CON3 W_DISABLE - * 4-CON2 CLKREQ# - * 5-USB3 overcurrent - * 6-USB3 power - * 7-CON2 W_DISABLE - * 8-JP4 P1 - * 9-JP4 P4 - * 10-JP4 P5 - * 11-m.2 DEVSLP - * 12-SFP_LOS - * 13-SFP_TX_FAULT - * 14-SFP_TX_DISABLE - * 15-SFP_MOD_DEF0 - */ - expander0: gpio-expander@20 { - /* - * This is how it should be: - * compatible = "onnn,pca9655", - * "nxp,pca9555"; - * but you can't do this because of - * the way I2C works. - */ - compatible = "nxp,pca9555"; - gpio-controller; - #gpio-cells = <2>; - reg = <0x20>; - - pcie1_0_clkreq { - gpio-hog; - gpios = <0 GPIO_ACTIVE_LOW>; - input; - line-name = "pcie1.0-clkreq"; - }; - pcie1_0_w_disable { - gpio-hog; - gpios = <3 GPIO_ACTIVE_LOW>; - output-low; - line-name = "pcie1.0-w-disable"; - }; - pcie2_0_clkreq { - gpio-hog; - gpios = <4 GPIO_ACTIVE_LOW>; - input; - line-name = "pcie2.0-clkreq"; - }; - pcie2_0_w_disable { - gpio-hog; - gpios = <7 GPIO_ACTIVE_LOW>; - output-low; - line-name = "pcie2.0-w-disable"; - }; - usb3_ilimit { - gpio-hog; - gpios = <5 GPIO_ACTIVE_LOW>; - input; - line-name = "usb3-current-limit"; - }; - usb3_power { - gpio-hog; - gpios = <6 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb3-power"; - }; - m2_devslp { - gpio-hog; - gpios = <11 GPIO_ACTIVE_HIGH>; - output-low; - line-name = "m.2 devslp"; - }; - sfp_los { - /* SFP loss of signal */ - gpio-hog; - gpios = <12 GPIO_ACTIVE_HIGH>; - input; - line-name = "sfp-los"; - }; - sfp_tx_fault { - /* SFP laser fault */ - gpio-hog; - gpios = <13 GPIO_ACTIVE_HIGH>; - input; - line-name = "sfp-tx-fault"; - }; - sfp_tx_disable { - /* SFP transmit disable */ - gpio-hog; - gpios = <14 GPIO_ACTIVE_HIGH>; - output-low; - line-name = "sfp-tx-disable"; - }; - sfp_mod_def0 { - /* SFP module present */ - gpio-hog; - gpios = <15 GPIO_ACTIVE_LOW>; - input; - line-name = "sfp-mod-def0"; - }; - }; - - /* The MCP3021 is 100kHz clock only */ - mikrobus_adc: mcp3021@4c { - compatible = "microchip,mcp3021"; - reg = <0x4c>; - }; - - /* Also something at 0x64 */ - }; - - i2c@11100 { - /* - * Routed to SFP, mikrobus, and PCIe. - * SFP limits this to 100kHz, and requires - * an AT24C01A/02/04 with address pins tied - * low, which takes addresses 0x50 and 0x51. - * Mikrobus doesn't specify beyond an I2C - * bus being present. - * PCIe uses ARP to assign addresses, or - * 0x63-0x64. - */ - clock-frequency = <100000>; - pinctrl-0 = <&clearfog_i2c1_pins>; - pinctrl-names = "default"; - status = "okay"; - }; - - pinctrl@18000 { - clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins { - marvell,pins = "mpp46"; - marvell,function = "ref"; - }; - clearfog_dsa0_pins: clearfog-dsa0-pins { - marvell,pins = "mpp23", "mpp41"; - marvell,function = "gpio"; - }; - clearfog_i2c1_pins: i2c1-pins { - /* SFP, PCIe, mSATA, mikrobus */ - marvell,pins = "mpp26", "mpp27"; - marvell,function = "i2c1"; - }; - clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins { - marvell,pins = "mpp20"; - marvell,function = "gpio"; - }; - clearfog_spi1_cs_pins: spi1-cs-pins { - marvell,pins = "mpp55"; - marvell,function = "spi1"; - }; - mikro_pins: mikro-pins { - /* int: mpp22 rst: mpp29 */ - marvell,pins = "mpp22", "mpp29"; - marvell,function = "gpio"; - }; - mikro_spi_pins: mikro-spi-pins { - marvell,pins = "mpp43"; - marvell,function = "spi1"; - }; - mikro_uart_pins: mikro-uart-pins { - marvell,pins = "mpp24", "mpp25"; - marvell,function = "ua1"; - }; - rear_button_pins: rear-button-pins { - marvell,pins = "mpp34"; - marvell,function = "gpio"; - }; - }; - - sata@a8000 { - /* pinctrl? */ - status = "okay"; - }; - - sata@e0000 { - /* pinctrl? */ - status = "okay"; - }; - - sdhci@d8000 { - bus-width = <4>; - cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; - no-1-8-v; - pinctrl-0 = <µsom_sdhci_pins - &clearfog_sdhci_cd_pins>; - pinctrl-names = "default"; - status = "okay"; - vmmc = <®_3p3v>; - wp-inverted; - }; - - serial@12100 { - /* mikrobus uart */ - pinctrl-0 = <&mikro_uart_pins>; - pinctrl-names = "default"; - status = "okay"; - }; - - usb@58000 { - /* CON3, nearest power. */ - status = "okay"; - }; - - usb3@f0000 { - /* CON2, nearest CPU, USB2 only. */ - status = "okay"; - }; - - usb3@f8000 { - /* CON7 */ - status = "okay"; - }; - }; - - pcie-controller { - status = "okay"; - /* - * The two PCIe units are accessible through - * the mini-PCIe connectors on the board. - */ - pcie@2,0 { - /* Port 1, Lane 0. CON3, nearest power. */ - reset-gpios = <&expander0 1 GPIO_ACTIVE_LOW>; - status = "okay"; - }; - pcie@3,0 { - /* Port 2, Lane 0. CON2, nearest CPU. */ - reset-gpios = <&expander0 2 GPIO_ACTIVE_LOW>; - status = "okay"; - }; - }; - }; - - dsa@0 { - compatible = "marvell,dsa"; - dsa,ethernet = <ð1>; - dsa,mii-bus = <&mdio>; - pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>; - pinctrl-names = "default"; - #address-cells = <2>; - #size-cells = <0>; - - switch@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <4 0>; - - port@0 { - reg = <0>; - label = "lan5"; - }; - - port@1 { - reg = <1>; - label = "lan4"; - }; - - port@2 { - reg = <2>; - label = "lan3"; - }; - - port@3 { - reg = <3>; - label = "lan2"; - }; - - port@4 { - reg = <4>; - label = "lan1"; - }; - - port@5 { - reg = <5>; - label = "cpu"; - }; - - port@6 { - /* 88E1512 external phy */ - reg = <6>; - label = "lan6"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - pinctrl-0 = <&rear_button_pins>; - pinctrl-names = "default"; - - button_0 { - /* The rear SW3 button */ - label = "Rear Button"; - gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; - linux,can-disable; - linux,code = <BTN_0>; - }; - }; -}; - -&spi1 { - /* - * Add SPI CS pins for clearfog: - * CS0: W25Q32 (not populated on uSOM) - * CS1: - * CS2: mikrobus - */ - pinctrl-0 = <&spi1_pins - &clearfog_spi1_cs_pins - &mikro_spi_pins>; - pinctrl-names = "default"; - status = "okay"; }; |