diff options
Diffstat (limited to 'arch/arm/boot/dts/meson8b-ec100.dts')
-rw-r--r-- | arch/arm/boot/dts/meson8b-ec100.dts | 415 |
1 files changed, 0 insertions, 415 deletions
diff --git a/arch/arm/boot/dts/meson8b-ec100.dts b/arch/arm/boot/dts/meson8b-ec100.dts deleted file mode 100644 index bed1dfef1985..000000000000 --- a/arch/arm/boot/dts/meson8b-ec100.dts +++ /dev/null @@ -1,415 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -/* - * Copyright (c) 2018 Martin Blumenstingl <martin.blumenstingl@googlemail.com>. - */ - -/dts-v1/; - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/input/input.h> - -#include "meson8b.dtsi" - -/ { - model = "Endless Computers Endless Mini"; - compatible = "endless,ec100", "amlogic,meson8b"; - - aliases { - serial0 = &uart_AO; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory { - device_type = "memory"; - reg = <0x40000000 0x40000000>; - }; - - gpio-keys { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - pal-switch { - label = "pal"; - linux,input-type = <EV_SW>; - linux,code = <KEY_SWITCHVIDEOMODE>; - gpios = <&gpio GPIOH_7 GPIO_ACTIVE_LOW>; - }; - - ntsc-switch { - label = "ntsc"; - linux,input-type = <EV_SW>; - linux,code = <KEY_SWITCHVIDEOMODE>; - gpios = <&gpio GPIOH_8 GPIO_ACTIVE_HIGH>; - }; - - power-button { - label = "power"; - linux,code = <KEY_POWER>; - gpios = <&gpio GPIOH_9 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-poweroff { - compatible = "gpio-poweroff"; - /* - * shutdown is managed by the EC (embedded micro-controller) - * which is configured through GPIOAO_2 (poweroff GPIO) and - * GPIOAO_7 (power LED, which has to go LOW as well). - */ - gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>; - timeout-ms = <20000>; - }; - - iio-hwmon { - compatible = "iio-hwmon"; - io-channels = <&saradc 8>; - }; - - leds { - compatible = "gpio-leds"; - - power { - label = "ec100:red:power"; - /* - * Needs to go LOW (together with the poweroff GPIO) - * during shutdown to allow the EC (embedded - * micro-controller) to shutdown the system. Setting - * the output to LOW signals the EC to start a - * "breathing"/pulsing effect until the power is fully - * turned off. - */ - gpios = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - }; - - rtc32k_xtal: rtc32k-xtal-clk { - /* X2 in the schematics */ - compatible = "fixed-clock"; - clock-frequency = <32768>; - clock-output-names = "RTC32K"; - #clock-cells = <0>; - }; - - usb_vbus: regulator-usb-vbus { - /* - * Silergy SY6288CCAC-GP 2A Power Distribution Switch. - */ - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - vin-supply = <&vcc_5v>; - - /* - * signal name from the schematics: USB_PWR_EN - */ - gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - vcc_5v: regulator-vcc5v { - /* - * supplied by the main power input which called PWR_5V_STB - * in the schematics - */ - compatible = "regulator-fixed"; - - regulator-name = "VCC5V"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - /* - * signal name from the schematics: 3V3_5V_EN - */ - gpio = <&gpio GPIODV_29 GPIO_ACTIVE_LOW>; - - regulator-boot-on; - regulator-always-on; - }; - - vcck: regulator-vcck { - /* - * Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz - * Synchronous Step Down Regulator. - */ - compatible = "pwm-regulator"; - - regulator-name = "VCCK"; - regulator-min-microvolt = <860000>; - regulator-max-microvolt = <1140000>; - - vin-supply = <&vcc_5v>; - - pwms = <&pwm_cd 0 1148 0>; - pwm-dutycycle-range = <100 0>; - - regulator-boot-on; - regulator-always-on; - }; - - vcc_1v8: regulator-vcc1v8 { - /* - * ABLIC S-1339D18-M5001-GP - */ - compatible = "regulator-fixed"; - - regulator-name = "VCC1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - - vin-supply = <&vcc_3v3>; - }; - - vcc_3v3: regulator-vcc3v3 { - /* - * Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz - * Synchronous Step Down Regulator. Also called - * VDDIO_AO3.3V in the schematics. - */ - compatible = "regulator-fixed"; - - regulator-name = "VCC3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - vin-supply = <&vcc_5v>; - }; - - vcc_ddr3: regulator-vcc-ddr3 { - /* - * Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz - * Synchronous Step Down Regulator. Also called - * DDR3_1.5V in the schematics. - */ - compatible = "regulator-fixed"; - - regulator-name = "VCC_DDR3_1V5"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - - vin-supply = <&vcc_5v>; - - regulator-boot-on; - regulator-always-on; - }; - - vcc_rtc: regulator-vcc-rtc { - /* - * Global Mixed-mode Technology Inc. G918T12U-GP - */ - compatible = "regulator-fixed"; - - regulator-name = "VCC_RTC"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <900000>; - - /* - * When the board is powered then the input is VCC3V3, - * otherwise power is taken from the coin cell battery. - */ - vin-supply = <&vcc_3v3>; - }; - - vddee: regulator-vddee { - /* - * Silergy SY8089AAC-GP 2A continuous, 3A peak, 1MHz - * Synchronous Step Down Regulator. Also called VDDAO - * in a part of the schematics. - */ - compatible = "pwm-regulator"; - - regulator-name = "VDDEE"; - regulator-min-microvolt = <860000>; - regulator-max-microvolt = <1140000>; - - vin-supply = <&vcc_5v>; - - pwms = <&pwm_cd 1 1148 0>; - pwm-dutycycle-range = <100 0>; - - regulator-boot-on; - regulator-always-on; - }; -}; - -&cpu0 { - cpu-supply = <&vcck>; -}; - -ðmac { - status = "okay"; - - pinctrl-0 = <ð_rmii_pins>; - pinctrl-names = "default"; - - phy-handle = <ð_phy0>; - phy-mode = "rmii"; - - mdio { - compatible = "snps,dwmac-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - eth_phy0: ethernet-phy@0 { - /* IC Plus IP101A/G (0x02430c54) */ - reg = <0>; - - reset-assert-us = <10000>; - reset-deassert-us = <10000>; - reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; - - icplus,select-interrupt; - interrupt-parent = <&gpio_intc>; - /* GPIOH_3 */ - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; - }; - }; -}; - -&i2c_A { - status = "okay"; - pinctrl-0 = <&i2c_a_pins>; - pinctrl-names = "default"; - - rt5640: codec@1c { - compatible = "realtek,rt5640"; - reg = <0x1c>; - interrupt-parent = <&gpio_intc>; - interrupts = <13 IRQ_TYPE_EDGE_BOTH>; /* GPIOAO_13 */ - realtek,in1-differential; - }; -}; - -&mali { - mali-supply = <&vddee>; -}; - -&saradc { - status = "okay"; - vref-supply = <&vcc_1v8>; -}; - -&sdio { - status = "okay"; - - pinctrl-0 = <&sd_b_pins>; - pinctrl-names = "default"; - - /* SD card */ - sd_card_slot: slot@1 { - compatible = "mmc-slot"; - reg = <1>; - status = "okay"; - - bus-width = <4>; - no-sdio; - cap-mmc-highspeed; - cap-sd-highspeed; - disable-wp; - - cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>; - - vmmc-supply = <&vcc_3v3>; - }; -}; - -&gpio_ao { - gpio-line-names = "Linux_TX", "Linux_RX", - "SLP_S5_N", "USB2_OC_FLAG#", - "HUB_RST", "USB_PWR_EN", - "I2S_IN", "SLP_S1_N", - "TCK", "TMS", "TDI", "TDO", - "HDMI_CEC", "5640_IRQ", - "MUTE", "S805_TEST#"; -}; - -&gpio { - gpio-line-names = /* Bank GPIOX */ - "WIFI_SD_D0", "WIFI_SD_D1", "WIFI_SD_D2", - "WIFI_SD_D3", "BTPCM_DOUT", "BTPCM_DIN", - "BTPCM_SYNC", "BTPCM_CLK", "WIFI_SD_CLK", - "WIFI_SD_CMD", "WIFI_32K", "WIFI_PWREN", - "UART_B_TX", "UART_B_RX", "UART_B_CTS_N", - "UART_B_RTS_N", "BT_EN", "WIFI_WAKE_HOST", - /* Bank GPIOY */ - "", "", "", "", "", "", "", "", "", "", - "", "", - /* Bank GPIODV */ - "VCCK_PWM_C", "I2C_SDA_A", "I2C_SCL_A", - "I2C_SDA_B", "I2C_SCL_B", "VDDEE_PWM_D", - "VDDEE_PWM 3V3_5V_EN", - /* Bank GPIOH */ - "HDMI_HPD", "HDMI_I2C_SDA", "HDMI_I2C_SCL", - "RMII_IRQ", "RMII_RST#", "RMII_TXD1", - "RMII_TXD0", "AV_select_1", "AV_select_2", - "MCU_Control_S", - /* Bank CARD */ - "SD_D1_B", "SD_D0_B", "SD_CLK_8726MX", - "SD_CMD_8726MX", "SD_D3_B", "SD_D2_B", - "CARD_EN_DET (CARD_DET)", - /* Bank BOOT */ - "NAND_D0 (EMMC)", "NAND_D1 (EMMC)", - "NAND_D2 (EMMC)", "NAND_D3 (EMMC)", - "NAND_D4 (EMMC)", "NAND_D5 (EMMC)", - "NAND_D6 (EMMC)", "NAND_D7 (EMMC)", - "NAND_CS1 (EMMC)", "NAND_CS2 iNAND_RS1 (EMMC)", - "NAND_nR/B iNAND_CMD (EMMC)", "NAND_ALE (EMMC)", - "NAND_CLE (EMMC)", "nRE_S1 NAND_nRE (EMMC)", - "nWE_S1 NAND_nWE (EMMC)", "", "", "SPI_CS", - /* Bank DIF */ - "RMII_RXD1", "RMII_RXD0", "RMII_CRS_DV", - "RMII_50M_IN", "GPIODIF_4", "GPIODIF_5", - "RMII_TXEN", "CPUETH_25MOUT", "RMII_MDC", - "RMII_MDIO"; -}; - -&pwm_cd { - status = "okay"; - pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>; - pinctrl-names = "default"; - clocks = <&clkc CLKID_XTAL>, <&clkc CLKID_XTAL>; - clock-names = "clkin0", "clkin1"; -}; - -&rtc { - status = "okay"; - clocks = <&rtc32k_xtal>; - vdd-supply = <&vcc_rtc>; -}; - -/* exposed through the pin headers labeled "URDUG1" on the top of the PCB */ -&uart_AO { - status = "okay"; - pinctrl-0 = <&uart_ao_a_pins>; - pinctrl-names = "default"; -}; - -/* - * connected to the Bluetooth part of the RTL8723BS SDIO wifi / Bluetooth - * combo chip. This is only available on the variant with 2GB RAM. - */ -&uart_B { - status = "okay"; - pinctrl-0 = <&uart_b0_pins>, <&uart_b0_cts_rts_pins>; - pinctrl-names = "default"; - uart-has-rtscts; -}; - -&usb1 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&usb1_phy { - status = "okay"; -}; |