diff options
Diffstat (limited to 'arch/arm/boot/dts/meson8b-odroidc1.dts')
-rw-r--r-- | arch/arm/boot/dts/meson8b-odroidc1.dts | 365 |
1 files changed, 0 insertions, 365 deletions
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts deleted file mode 100644 index a24eccc354b9..000000000000 --- a/arch/arm/boot/dts/meson8b-odroidc1.dts +++ /dev/null @@ -1,365 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 OR MIT -/* - * Copyright 2015 Endless Mobile, Inc. - * Author: Carlo Caione <carlo@endlessm.com> - */ - -/dts-v1/; -#include "meson8b.dtsi" -#include <dt-bindings/gpio/gpio.h> - -/ { - model = "Hardkernel ODROID-C1"; - compatible = "hardkernel,odroid-c1", "amlogic,meson8b"; - - aliases { - serial0 = &uart_AO; - mmc0 = &sd_card_slot; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory { - device_type = "memory"; - reg = <0x40000000 0x40000000>; - }; - - leds { - compatible = "gpio-leds"; - blue { - label = "c1:blue:alive"; - gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - }; - - p5v0: regulator-p5v0 { - compatible = "regulator-fixed"; - - regulator-name = "P5V0"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - }; - - tflash_vdd: regulator-tflash_vdd { - /* - * signal name from schematics: TFLASH_VDD_EN - */ - compatible = "regulator-fixed"; - - regulator-name = "TFLASH_VDD"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - vin-supply = <&vcc_3v3>; - - gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - tf_io: gpio-regulator-tf_io { - compatible = "regulator-gpio"; - - regulator-name = "TF_IO"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - - vin-supply = <&vcc_3v3>; - - /* - * signal name from schematics: TF_3V3N_1V8_EN - */ - gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>; - gpios-states = <0>; - - states = <3300000 0 - 1800000 1>; - }; - - iio-hwmon { - compatible = "iio-hwmon"; - io-channels = <&saradc 8>; - }; - - rtc32k_xtal: rtc32k-xtal-clk { - /* X3 in the schematics */ - compatible = "fixed-clock"; - clock-frequency = <32768>; - clock-output-names = "RTC32K"; - #clock-cells = <0>; - }; - - vcc_1v8: regulator-vcc-1v8 { - /* - * RICHTEK RT9179 configured for a fixed output voltage of - * 1.8V. This supplies not only VCC1V8 but also IOREF_1V8 and - * VDD1V8 according to the schematics. - */ - compatible = "regulator-fixed"; - - regulator-name = "VCC1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - - vin-supply = <&p5v0>; - }; - - vcc_3v3: regulator-vcc-3v3 { - /* - * Monolithic Power Systems MP2161 configured for a fixed - * output voltage of 3.3V. This supplies not only VCC3V3 but - * also VDD3V3 and VDDIO_AO3V3 according to the schematics. - */ - compatible = "regulator-fixed"; - - regulator-name = "VCC3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - vin-supply = <&p5v0>; - }; - - vcck: regulator-vcck { - /* Monolithic Power Systems MP2161 */ - compatible = "pwm-regulator"; - - regulator-name = "VCCK"; - regulator-min-microvolt = <860000>; - regulator-max-microvolt = <1140000>; - - vin-supply = <&p5v0>; - - pwms = <&pwm_cd 0 12218 0>; - pwm-dutycycle-range = <91 0>; - - regulator-boot-on; - regulator-always-on; - }; - - vddc_ddr: regulator-vddc-ddr { - /* - * Monolithic Power Systems MP2161 configured for a fixed - * output voltage of 1.5V. This supplies not only DDR_VDDC but - * also DDR3_1V5 according to the schematics. - */ - compatible = "regulator-fixed"; - - regulator-name = "DDR_VDDC"; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - - vin-supply = <&p5v0>; - }; - - vddee: regulator-vddee { - /* Monolithic Power Systems MP2161 */ - compatible = "pwm-regulator"; - - regulator-name = "VDDEE"; - regulator-min-microvolt = <860000>; - regulator-max-microvolt = <1140000>; - - vin-supply = <&p5v0>; - - pwms = <&pwm_cd 1 12218 0>; - pwm-dutycycle-range = <91 0>; - - regulator-boot-on; - regulator-always-on; - }; - - vdd_rtc: regulator-vdd-rtc { - /* - * Torex Semiconductor XC6215 configured for a fixed output of - * 0.9V. - */ - compatible = "regulator-fixed"; - - regulator-name = "VDD_RTC"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <900000>; - - vin-supply = <&vcc_3v3>; - }; -}; - -&cpu0 { - cpu-supply = <&vcck>; -}; - -&efuse { - ethernet_mac_address: mac@1b4 { - reg = <0x1b4 0x6>; - }; -}; - -ðmac { - status = "okay"; - - pinctrl-0 = <ð_rgmii_pins>; - pinctrl-names = "default"; - - phy-mode = "rgmii"; - phy-handle = <ð_phy>; - amlogic,tx-delay-ns = <4>; - - nvmem-cells = <ðernet_mac_address>; - nvmem-cell-names = "mac-address"; - - mdio { - compatible = "snps,dwmac-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - /* Realtek RTL8211F (0x001cc916) */ - eth_phy: ethernet-phy@0 { - reg = <0>; - - reset-assert-us = <10000>; - reset-deassert-us = <30000>; - reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; - - interrupt-parent = <&gpio_intc>; - /* GPIOH_3 */ - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; - }; - }; -}; - -&gpio { - gpio-line-names = /* Bank GPIOX */ - "J2 Header Pin 35", "J2 Header Pin 36", - "J2 Header Pin 32", "J2 Header Pin 31", - "J2 Header Pin 29", "J2 Header Pin 18", - "J2 Header Pin 22", "J2 Header Pin 16", - "J2 Header Pin 23", "J2 Header Pin 21", - "J2 Header Pin 19", "J2 Header Pin 33", - "J2 Header Pin 8", "J2 Header Pin 10", - "J2 Header Pin 15", "J2 Header Pin 13", - "J2 Header Pin 24", "J2 Header Pin 26", - /* Bank GPIOY */ - "Revision (upper)", "Revision (lower)", - "J2 Header Pin 7", "", "J2 Header Pin 12", - "J2 Header Pin 11", "", "", "", - "TFLASH_VDD_EN", "", "", - /* Bank GPIODV */ - "VCCK_PWM (PWM_C)", "I2CA_SDA", "I2CA_SCL", - "I2CB_SDA", "I2CB_SCL", "VDDEE_PWM (PWM_D)", - "", - /* Bank GPIOH */ - "HDMI_HPD", "HDMI_I2C_SDA", "HDMI_I2C_SCL", - "ETH_PHY_INTR", "ETH_PHY_NRST", "ETH_TXD1", - "ETH_TXD0", "ETH_TXD3", "ETH_TXD2", - "ETH_RGMII_TX_CLK", - /* Bank CARD */ - "SD_DATA1 (SDB_D1)", "SD_DATA0 (SDB_D0)", - "SD_CLK", "SD_CMD", "SD_DATA3 (SDB_D3)", - "SD_DATA2 (SDB_D2)", "SD_CDN (SD_DET_N)", - /* Bank BOOT */ - "SDC_D0 (EMMC)", "SDC_D1 (EMMC)", - "SDC_D2 (EMMC)", "SDC_D3 (EMMC)", - "SDC_D4 (EMMC)", "SDC_D5 (EMMC)", - "SDC_D6 (EMMC)", "SDC_D7 (EMMC)", - "SDC_CLK (EMMC)", "SDC_RSTn (EMMC)", - "SDC_CMD (EMMC)", "BOOT_SEL", "", "", "", - "", "", "", "", - /* Bank DIF */ - "ETH_RXD1", "ETH_RXD0", "ETH_RX_DV", - "RGMII_RX_CLK", "ETH_RXD3", "ETH_RXD2", - "ETH_TXEN", "ETH_PHY_REF_CLK_25MOUT", - "ETH_MDC", "ETH_MDIO"; -}; - -&gpio_ao { - gpio-line-names = "UART TX", "UART RX", "", - "TF_3V3N_1V8_EN", "USB_HUB_RST_N", - "USB_OTG_PWREN", "J7 Header Pin 2", - "IR_IN", "J7 Header Pin 4", - "J7 Header Pin 6", "J7 Header Pin 5", - "J7 Header Pin 7", "HDMI_CEC", - "SYS_LED", "", ""; - - /* - * WARNING: The USB Hub on the Odroid-C1/C1+ needs a reset signal - * to be turned high in order to be detected by the USB Controller. - * This signal should be handled by a USB specific power sequence - * in order to reset the Hub when USB bus is powered down. - */ - usb-hub { - gpio-hog; - gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb-hub-reset"; - }; -}; - -&ir_receiver { - status = "okay"; - pinctrl-0 = <&ir_recv_pins>; - pinctrl-names = "default"; -}; - -&mali { - mali-supply = <&vddee>; -}; - -&saradc { - status = "okay"; - vref-supply = <&vcc_1v8>; -}; - -&sdio { - status = "okay"; - - pinctrl-0 = <&sd_b_pins>; - pinctrl-names = "default"; - - /* SD card */ - sd_card_slot: slot@1 { - compatible = "mmc-slot"; - reg = <1>; - status = "okay"; - - bus-width = <4>; - no-sdio; - cap-mmc-highspeed; - cap-sd-highspeed; - disable-wp; - - cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>; - - vmmc-supply = <&tflash_vdd>; - vqmmc-supply = <&tf_io>; - }; -}; - -&pwm_cd { - status = "okay"; - pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>; - pinctrl-names = "default"; - clocks = <&clkc CLKID_XTAL>, <&clkc CLKID_XTAL>; - clock-names = "clkin0", "clkin1"; -}; - -&rtc { - /* needs to be enabled manually when a battery is connected */ - clocks = <&rtc32k_xtal>; - vdd-supply = <&vdd_rtc>; -}; - -&uart_AO { - status = "okay"; - pinctrl-0 = <&uart_ao_a_pins>; - pinctrl-names = "default"; -}; - -&usb1_phy { - status = "okay"; -}; - -&usb1 { - status = "okay"; -}; |