1 files changed, 0 insertions, 167 deletions
diff --git a/arch/arm/mach-ixp4xx/gtwx5715-setup.c b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
deleted file mode 100644
index 28f0d2a8a829..000000000000
--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+++ /dev/null
@@ -1,167 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * arch/arm/mach-ixp4xx/gtwx5715-setup.c
- *
- * Gemtek GTWX5715 (Linksys WRV54G) board setup
- *
- * Copyright (C) 2004 George T. Joseph
- * Derived from Coyote
- */
-
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/serial_8250.h>
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-
-#include "irqs.h"
-
-/* GPIO 5,6,7 and 12 are hard wired to the Kendin KS8995M Switch
-   and operate as an SPI type interface.  The details of the interface
-   are available on Kendin/Micrel's web site. */
-
-#define GTWX5715_KSSPI_SELECT	5
-#define GTWX5715_KSSPI_TXD	6
-#define GTWX5715_KSSPI_CLOCK	7
-#define GTWX5715_KSSPI_RXD	12
-
-/* The "reset" button is wired to GPIO 3.
-   The GPIO is brought "low" when the button is pushed. */
-
-#define GTWX5715_BUTTON_GPIO	3
-
-/* Board Label      Front Label
-   LED1             Power
-   LED2             Wireless-G
-   LED3             not populated but could be
-   LED4             Internet
-   LED5 - LED8      Controlled by KS8995M Switch
-   LED9             DMZ */
-
-#define GTWX5715_LED1_GPIO	2
-#define GTWX5715_LED2_GPIO	9
-#define GTWX5715_LED3_GPIO	8
-#define GTWX5715_LED4_GPIO	1
-#define GTWX5715_LED9_GPIO	4
-
-/*
- * Xscale UART registers are 32 bits wide with only the least
- * significant 8 bits having any meaning.  From a configuration
- * perspective, this means 2 things...
- *
- *   Setting .regshift = 2 so that the standard 16550 registers
- *   line up on every 4th byte.
- *
- *   Shifting the register start virtual address +3 bytes when
- *   compiled big-endian.  Since register writes are done on a
- *   single byte basis, if the shift isn't done the driver will
- *   write the value into the most significant byte of the register,
- *   which is ignored, instead of the least significant.
- */
-
-#ifdef	__ARMEB__
-#define	REG_OFFSET	3
-#else
-#define	REG_OFFSET	0
-#endif
-
-/*
- * Only the second or "console" uart is connected on the gtwx5715.
- */
-
-static struct resource gtwx5715_uart_resources[] = {
-	{
-		.start	= IXP4XX_UART2_BASE_PHYS,
-		.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= IRQ_IXP4XX_UART2,
-		.end	= IRQ_IXP4XX_UART2,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{ },
-};
-
-
-static struct plat_serial8250_port gtwx5715_uart_platform_data[] = {
-	{
-	.mapbase	= IXP4XX_UART2_BASE_PHYS,
-	.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
-	.irq		= IRQ_IXP4XX_UART2,
-	.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-	.iotype		= UPIO_MEM,
-	.regshift	= 2,
-	.uartclk	= IXP4XX_UART_XTAL,
-	},
-	{ },
-};
-
-static struct platform_device gtwx5715_uart_device = {
-	.name		= "serial8250",
-	.id		= PLAT8250_DEV_PLATFORM,
-	.dev			= {
-		.platform_data	= gtwx5715_uart_platform_data,
-	},
-	.num_resources	= 2,
-	.resource	= gtwx5715_uart_resources,
-};
-
-static struct flash_platform_data gtwx5715_flash_data = {
-	.map_name	= "cfi_probe",
-	.width		= 2,
-};
-
-static struct resource gtwx5715_flash_resource = {
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device gtwx5715_flash = {
-	.name		= "IXP4XX-Flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &gtwx5715_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &gtwx5715_flash_resource,
-};
-
-static struct platform_device *gtwx5715_devices[] __initdata = {
-	&gtwx5715_uart_device,
-	&gtwx5715_flash,
-};
-
-static void __init gtwx5715_init(void)
-{
-	ixp4xx_sys_init();
-
-	gtwx5715_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
-	gtwx5715_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_8M - 1;
-
-	platform_add_devices(gtwx5715_devices, ARRAY_SIZE(gtwx5715_devices));
-}
-
-
-MACHINE_START(GTWX5715, "Gemtek GTWX5715 (Linksys WRV54G)")
-	/* Maintainer: George Joseph */
-	.map_io		= ixp4xx_map_io,
-	.init_early	= ixp4xx_init_early,
-	.init_irq	= ixp4xx_init_irq,
-	.init_time	= ixp4xx_timer_init,
-	.atag_offset	= 0x100,
-	.init_machine	= gtwx5715_init,
-#if defined(CONFIG_PCI)
-	.dma_zone_size	= SZ_64M,
-#endif
-	.restart	= ixp4xx_restart,
-MACHINE_END
-
-