summaryrefslogtreecommitdiff
path: root/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts')
-rw-r--r--arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts184
1 files changed, 1 insertions, 183 deletions
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
index fbcf03f86c96..1542d836c090 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
@@ -12,191 +12,9 @@
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include "armada-372x.dtsi"
+#include "armada-3720-espressobin.dtsi"
/ {
model = "Globalscale Marvell ESPRESSOBin Board";
compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710";
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
- };
-
- vcc_sd_reg1: regulator {
- compatible = "regulator-gpio";
- regulator-name = "vcc_sd1";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
-
- gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
- states = <1800000 0x1
- 3300000 0x0>;
- enable-active-high;
- };
-};
-
-/* J9 */
-&pcie0 {
- status = "okay";
- phys = <&comphy1 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
-};
-
-/* J6 */
-&sata {
- status = "okay";
- phys = <&comphy2 0>;
- phy-names = "sata-phy";
-};
-
-/* J1 */
-&sdhci1 {
- wp-inverted;
- bus-width = <4>;
- cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
- marvell,pad-type = "sd";
- vqmmc-supply = <&vcc_sd_reg1>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&sdio_pins>;
- status = "okay";
-};
-
-/* U11 */
-&sdhci0 {
- non-removable;
- bus-width = <8>;
- mmc-ddr-1_8v;
- mmc-hs400-1_8v;
- marvell,xenon-emmc;
- marvell,xenon-tun-count = <9>;
- marvell,pad-type = "fixed-1-8v";
-
- pinctrl-names = "default";
- pinctrl-0 = <&mmc_pins>;
-/*
- * This eMMC is not populated on all boards, so disable it by
- * default and let the bootloader enable it, if it is present
- */
- status = "disabled";
-};
-
-&spi0 {
- status = "okay";
-
- flash@0 {
- reg = <0>;
- compatible = "jedec,spi-nor";
- spi-max-frequency = <104000000>;
- m25p,fast-read;
- };
-};
-
-/* Exported on the micro USB connector J5 through an FTDI */
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>;
- status = "okay";
-};
-
-/*
- * Connector J17 and J18 expose a number of different features. Some pins are
- * multiplexed. This is the case for instance for the following features:
- * - UART1 (pin 24 = RX, pin 26 = TX). See armada-3720-db.dts for an example of
- * how to enable it. Beware that the signals are 1.8V TTL.
- * - I2C
- * - SPI
- * - MMC
- */
-
-/* J7 */
-&usb3 {
- status = "okay";
-};
-
-/* J8 */
-&usb2 {
- status = "okay";
-};
-
-&mdio {
- switch0: switch0@1 {
- compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- dsa,member = <0 0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&eth0>;
- phy-mode = "rgmii-id";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "wan";
- phy-handle = <&switch0phy0>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan0";
- phy-handle = <&switch0phy1>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan1";
- phy-handle = <&switch0phy2>;
- };
-
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- switch0phy0: switch0phy0@11 {
- reg = <0x11>;
- };
- switch0phy1: switch0phy1@12 {
- reg = <0x12>;
- };
- switch0phy2: switch0phy2@13 {
- reg = <0x13>;
- };
- };
- };
-};
-
-&eth0 {
- pinctrl-names = "default";
- pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
- phy-mode = "rgmii-id";
- status = "okay";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
};