diff options
Diffstat (limited to 'arch/arm64/boot/dts/marvell/armada-7040-db.dts')
| -rw-r--r-- | arch/arm64/boot/dts/marvell/armada-7040-db.dts | 101 |
1 files changed, 80 insertions, 21 deletions
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-db.dts b/arch/arm64/boot/dts/marvell/armada-7040-db.dts index 9c3bdf87e543..3ae05eee2c9a 100644 --- a/arch/arm64/boot/dts/marvell/armada-7040-db.dts +++ b/arch/arm64/boot/dts/marvell/armada-7040-db.dts @@ -56,12 +56,18 @@ stdout-path = "serial0:115200n8"; }; - memory@00000000 { + memory@0 { device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; - cpm_reg_usb3_0_vbus: cpm-usb3-0-vbus { + aliases { + ethernet0 = &cp0_eth0; + ethernet1 = &cp0_eth1; + ethernet2 = &cp0_eth2; + }; + + cp0_reg_usb3_0_vbus: cp0-usb3-0-vbus { compatible = "regulator-fixed"; regulator-name = "usb3h0-vbus"; regulator-min-microvolt = <5000000>; @@ -70,7 +76,7 @@ gpio = <&expander0 0 GPIO_ACTIVE_HIGH>; }; - cpm_reg_usb3_1_vbus: cpm-usb3-1-vbus { + cp0_reg_usb3_1_vbus: cp0-usb3-1-vbus { compatible = "regulator-fixed"; regulator-name = "usb3h1-vbus"; regulator-min-microvolt = <5000000>; @@ -79,14 +85,14 @@ gpio = <&expander0 1 GPIO_ACTIVE_HIGH>; }; - cpm_usb3_0_phy: cpm-usb3-0-phy { + cp0_usb3_0_phy: cp0-usb3-0-phy { compatible = "usb-nop-xceiv"; - vcc-supply = <&cpm_reg_usb3_0_vbus>; + vcc-supply = <&cp0_reg_usb3_0_vbus>; }; - cpm_usb3_1_phy: cpm-usb3-1-phy { + cp0_usb3_1_phy: cp0-usb3-1-phy { compatible = "usb-nop-xceiv"; - vcc-supply = <&cpm_reg_usb3_1_vbus>; + vcc-supply = <&cp0_reg_usb3_1_vbus>; }; }; @@ -124,14 +130,16 @@ &uart0 { status = "okay"; + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; }; -&cpm_pcie2 { +&cp0_pcie2 { status = "okay"; }; -&cpm_i2c0 { +&cp0_i2c0 { status = "okay"; clock-frequency = <100000>; @@ -141,10 +149,50 @@ gpio-controller; #gpio-cells = <2>; reg = <0x21>; + /* + * IO0_0: USB3_PWR_EN0 IO1_0: USB_3_1_Dev_Detect + * IO0_1: USB3_PWR_EN1 IO1_1: USB2_1_current_limit + * IO0_2: DDR3_4_Detect IO1_2: Hcon_IO_RstN + * IO0_3: USB2_DEVICE_DETECT + * IO0_4: GPIO_0 IO1_4: SD_Status + * IO0_5: GPIO_1 IO1_5: LDO_5V_Enable + * IO0_6: IHB_5V_Enable IO1_6: PWR_EN_eMMC + * IO0_7: IO1_7: SDIO_Vcntrl + */ + }; +}; + +&cp0_nand { + /* + * SPI on CPM and NAND have common pins on this board. We can + * use only one at a time. To enable the NAND (whihch will + * disable the SPI), the "status = "okay";" line have to be + * added here. + */ + num-cs = <1>; + pinctrl-0 = <&nand_pins>, <&nand_rb>; + pinctrl-names = "default"; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + + partition@0 { + label = "U-Boot"; + reg = <0 0x200000>; + }; + partition@200000 { + label = "Linux"; + reg = <0x200000 0xe00000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; }; }; -&cpm_spi1 { + +&cp0_spi1 { status = "okay"; spi-flash@0 { @@ -172,17 +220,17 @@ }; }; -&cpm_sata0 { +&cp0_sata0 { status = "okay"; }; -&cpm_usb3_0 { - usb-phy = <&cpm_usb3_0_phy>; +&cp0_usb3_0 { + usb-phy = <&cp0_usb3_0_phy>; status = "okay"; }; -&cpm_usb3_1 { - usb-phy = <&cpm_usb3_1_phy>; +&cp0_usb3_1 { + usb-phy = <&cp0_usb3_1_phy>; status = "okay"; }; @@ -193,14 +241,14 @@ non-removable; }; -&cpm_sdhci0 { +&cp0_sdhci0 { status = "okay"; bus-width = <4>; no-1-8-v; - non-removable; + cd-gpios = <&expander0 12 GPIO_ACTIVE_LOW>; }; -&cpm_mdio { +&cp0_mdio { status = "okay"; phy0: ethernet-phy@0 { @@ -211,17 +259,28 @@ }; }; -&cpm_ethernet { +&cp0_ethernet { + status = "okay"; +}; + +&cp0_eth0 { status = "okay"; + /* Network PHY */ + phy-mode = "10gbase-kr"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy2 0>; }; -&cpm_eth1 { +&cp0_eth1 { status = "okay"; + /* Network PHY */ phy = <&phy0>; phy-mode = "sgmii"; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy0 1>; }; -&cpm_eth2 { +&cp0_eth2 { status = "okay"; phy = <&phy1>; phy-mode = "rgmii-id"; |