summaryrefslogtreecommitdiff
path: root/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi')
-rw-r--r--arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi900
1 files changed, 407 insertions, 493 deletions
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index 194343510dcb..3c7f97539390 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -3,38 +3,13 @@
* Copyright (c) 2015, The Linux Foundation. All rights reserved.
*/
-#include "msm8916.dtsi"
-#include "pm8916.dtsi"
+#include "msm8916-pm8916.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
#include <dt-bindings/sound/apq8016-lpass.h>
-/*
- * GPIO name legend: proper name = the GPIO line is used as GPIO
- * NC = not connected (pin out but not routed from the chip to
- * anything the board)
- * "[PER]" = pin is muxed for [peripheral] (not GPIO)
- * LSEC = Low Speed External Connector
- * HSEC = High Speed External Connector
- *
- * Line names are taken from the schematic "DragonBoard410c"
- * dated monday, august 31, 2015. Page 5 in particular.
- *
- * For the lines routed to the external connectors the
- * lines are named after the 96Boards CE Specification 1.0,
- * Appendix "Expansion Connector Signal Description".
- *
- * When the 96Board naming of a line and the schematic name of
- * the same line are in conflict, the 96Board specification
- * takes precedence, which means that the external UART on the
- * LSEC is named UART0 while the schematic and SoC names this
- * UART3. This is only for the informational lines i.e. "[FOO]",
- * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
- * ones actually used for GPIO.
- */
-
/ {
aliases {
serial0 = &blsp1_uart2;
@@ -76,7 +51,7 @@
};
reserved-memory {
- ramoops@bff00000{
+ ramoops@bff00000 {
compatible = "ramoops";
reg = <0x0 0xbff00000 0x0 0x100000>;
@@ -86,509 +61,190 @@
};
};
- soc {
- pinctrl@1000000 {
- gpio-line-names =
- "[UART0_TX]", /* GPIO_0, LSEC pin 5 */
- "[UART0_RX]", /* GPIO_1, LSEC pin 7 */
- "[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
- "[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
- "[UART1_TX]", /* GPIO_4, LSEC pin 11 */
- "[UART1_RX]", /* GPIO_5, LSEC pin 13 */
- "[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
- "[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
- "[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
- "[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
- "[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
- "[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
- "GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
- "GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
- "[I2C3_SDA]", /* HSEC pin 38 */
- "[I2C3_SCL]", /* HSEC pin 36 */
- "[SPI0_MOSI]", /* LSEC pin 14 */
- "[SPI0_MISO]", /* LSEC pin 10 */
- "[SPI0_CS_N]", /* LSEC pin 12 */
- "[SPI0_CLK]", /* LSEC pin 8 */
- "HDMI_HPD_N", /* GPIO 20 */
- "USR_LED_1_CTRL",
- "[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
- "[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
- "GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
- "GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
- "[CSI0_MCLK]", /* HSEC pin 15 */
- "[CSI1_MCLK]", /* HSEC pin 17 */
- "GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
- "[I2C2_SDA]", /* HSEC pin 34 */
- "[I2C2_SCL]", /* HSEC pin 32 */
- "DSI2HDMI_INT_N",
- "DSI_SW_SEL_APQ",
- "GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
- "GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
- "GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
- "GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
- "FORCED_USB_BOOT",
- "SD_CARD_DET_N",
- "[WCSS_BT_SSBI]",
- "[WCSS_WLAN_DATA_2]", /* GPIO 40 */
- "[WCSS_WLAN_DATA_1]",
- "[WCSS_WLAN_DATA_0]",
- "[WCSS_WLAN_SET]",
- "[WCSS_WLAN_CLK]",
- "[WCSS_FM_SSBI]",
- "[WCSS_FM_SDI]",
- "[WCSS_BT_DAT_CTL]",
- "[WCSS_BT_DAT_STB]",
- "NC",
- "NC", /* GPIO 50 */
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC", /* GPIO 60 */
- "NC",
- "NC",
- "[CDC_PDM0_CLK]",
- "[CDC_PDM0_SYNC]",
- "[CDC_PDM0_TX0]",
- "[CDC_PDM0_RX0]",
- "[CDC_PDM0_RX1]",
- "[CDC_PDM0_RX2]",
- "GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
- "NC", /* GPIO 70 */
- "NC",
- "NC",
- "NC",
- "NC", /* GPIO 74 */
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "BOOT_CONFIG_0", /* GPIO 80 */
- "BOOT_CONFIG_1",
- "BOOT_CONFIG_2",
- "BOOT_CONFIG_3",
- "NC",
- "NC",
- "BOOT_CONFIG_5",
- "NC",
- "NC",
- "NC",
- "NC", /* GPIO 90 */
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC", /* GPIO 100 */
- "NC",
- "NC",
- "NC",
- "SSBI_GPS",
- "NC",
- "NC",
- "KEY_VOLP_N",
- "NC",
- "NC",
- "[LS_EXP_MI2S_WS]", /* GPIO 110 */
- "NC",
- "NC",
- "[LS_EXP_MI2S_SCK]",
- "[LS_EXP_MI2S_DATA0]",
- "GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
- "NC",
- "[DSI2HDMI_MI2S_WS]",
- "[DSI2HDMI_MI2S_SCK]",
- "[DSI2HDMI_MI2S_DATA0]",
- "USR_LED_2_CTRL", /* GPIO 120 */
- "SB_HS_ID";
- };
-
- dma@7884000 {
- status = "okay";
- };
-
- serial@78af000 {
- label = "LS-UART0";
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp1_uart1_default>;
- pinctrl-1 = <&blsp1_uart1_sleep>;
- };
-
- serial@78b0000 {
- label = "LS-UART1";
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp1_uart2_default>;
- pinctrl-1 = <&blsp1_uart2_sleep>;
- };
-
- i2c@78b6000 {
- /* On Low speed expansion */
- label = "LS-I2C0";
- status = "okay";
- };
-
- i2c@78b8000 {
- /* On High speed expansion */
- label = "HS-I2C2";
- status = "okay";
-
- adv_bridge: bridge@39 {
- status = "okay";
-
- compatible = "adi,adv7533";
- reg = <0x39>;
-
- interrupt-parent = <&msmgpio>;
- interrupts = <31 2>;
-
- adi,dsi-lanes = <4>;
- clocks = <&rpmcc RPM_SMD_BB_CLK2>;
- clock-names = "cec";
-
- pd-gpios = <&msmgpio 32 0>;
-
- avdd-supply = <&pm8916_l6>;
- v1p2-supply = <&pm8916_l6>;
- v3p3-supply = <&pm8916_l17>;
-
- pinctrl-names = "default","sleep";
- pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
- pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
- #sound-dai-cells = <1>;
+ usb2513 {
+ compatible = "smsc,usb3503";
+ reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
+ initial-mode = <1>;
+ };
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
+ usb_id: usb-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_id_default>;
+ };
- port@0 {
- reg = <0>;
- adv7533_in: endpoint {
- remote-endpoint = <&dsi0_out>;
- };
- };
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
- port@1 {
- reg = <1>;
- adv7533_out: endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&adv7533_out>;
};
};
+ };
- i2c@78ba000 {
- /* On Low speed expansion */
- label = "LS-I2C1";
- status = "okay";
- };
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
- spi@78b7000 {
- /* On High speed expansion */
- label = "HS-SPI1";
- status = "okay";
- };
+ pinctrl-names = "default";
+ pinctrl-0 = <&msm_key_volp_n_default>;
- spi@78b9000 {
- /* On Low speed expansion */
- label = "LS-SPI0";
- status = "okay";
+ button@0 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
};
+ };
- leds {
- pinctrl-names = "default";
- pinctrl-0 = <&msmgpio_leds>,
- <&pm8916_gpios_leds>,
- <&pm8916_mpps_leds>;
-
- compatible = "gpio-leds";
-
- led@1 {
- label = "apq8016-sbc:green:user1";
- gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- led@2 {
- label = "apq8016-sbc:green:user2";
- gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- led@3 {
- label = "apq8016-sbc:green:user3";
- gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- led@4 {
- label = "apq8016-sbc:green:user4";
- gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- panic-indicator;
- default-state = "off";
- };
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&msmgpio_leds>,
+ <&pm8916_gpios_leds>,
+ <&pm8916_mpps_leds>;
- led@5 {
- label = "apq8016-sbc:yellow:wlan";
- gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "phy0tx";
- default-state = "off";
- };
+ compatible = "gpio-leds";
- led@6 {
- label = "apq8016-sbc:blue:bt";
- gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "bluetooth-power";
- default-state = "off";
- };
+ led@1 {
+ label = "apq8016-sbc:green:user1";
+ gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
};
- sdhci@7824000 {
- vmmc-supply = <&pm8916_l8>;
- vqmmc-supply = <&pm8916_l5>;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
- pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
- status = "okay";
+ led@2 {
+ label = "apq8016-sbc:green:user2";
+ gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
};
- sdhci@7864000 {
- vmmc-supply = <&pm8916_l11>;
- vqmmc-supply = <&pm8916_l12>;
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
- pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+ led@3 {
+ label = "apq8016-sbc:green:user3";
+ gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
- cd-gpios = <&msmgpio 38 0x1>;
- status = "okay";
+ led@4 {
+ label = "apq8016-sbc:green:user4";
+ gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "none";
+ panic-indicator;
+ default-state = "off";
};
- usb@78d9000 {
- extcon = <&usb_id>, <&usb_id>;
- status = "okay";
- adp-disable;
- hnp-disable;
- srp-disable;
- dr_mode = "otg";
- pinctrl-names = "default", "device";
- pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
- pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
- ulpi {
- phy {
- v1p8-supply = <&pm8916_l7>;
- v3p3-supply = <&pm8916_l13>;
- extcon = <&usb_id>;
- };
- };
+ led@5 {
+ label = "apq8016-sbc:yellow:wlan";
+ gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
};
- lpass@7708000 {
- status = "okay";
+ led@6 {
+ label = "apq8016-sbc:blue:bt";
+ gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ default-state = "off";
};
+ };
+};
- mdss@1a00000 {
- status = "okay";
+&blsp_dma {
+ status = "okay";
+};
- mdp@1a01000 {
- status = "okay";
- };
+&blsp_i2c2 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-I2C0";
+};
- dsi@1a98000 {
- status = "okay";
+&blsp_i2c4 {
+ /* On High speed expansion */
+ status = "okay";
+ label = "HS-I2C2";
- vdda-supply = <&pm8916_l2>;
- vddio-supply = <&pm8916_l6>;
+ adv_bridge: bridge@39 {
+ status = "okay";
- ports {
- port@1 {
- endpoint {
- remote-endpoint = <&adv7533_in>;
- data-lanes = <0 1 2 3>;
- };
- };
- };
- };
+ compatible = "adi,adv7533";
+ reg = <0x39>;
- dsi-phy@1a98300 {
- status = "okay";
+ interrupt-parent = <&msmgpio>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
- vddio-supply = <&pm8916_l6>;
- };
- };
+ adi,dsi-lanes = <4>;
+ clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+ clock-names = "cec";
- lpass_codec: codec{
- status = "okay";
- };
+ pd-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
- /*
- Internal Codec
- playback - Primary MI2S
- capture - Ter MI2S
-
- External Primary:
- playback - secondary MI2S
- capture - Quat MI2S
-
- External Secondary:
- playback - Quat MI2S
- capture - Quat MI2S
-
- */
-
- sound: sound {
- compatible = "qcom,apq8016-sbc-sndcard";
- reg = <0x07702000 0x4>, <0x07702004 0x4>;
- reg-names = "mic-iomux", "spkr-iomux";
-
- status = "okay";
- pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
- pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
- pinctrl-names = "default", "sleep";
- qcom,model = "DB410c";
- qcom,audio-routing =
- "AMIC2", "MIC BIAS Internal2",
- "AMIC3", "MIC BIAS External1";
-
- external-dai-link@0 {
- link-name = "ADV7533";
- cpu {
- sound-dai = <&lpass MI2S_QUATERNARY>;
- };
- codec {
- sound-dai = <&adv_bridge 0>;
- };
- };
+ avdd-supply = <&pm8916_l6>;
+ v1p2-supply = <&pm8916_l6>;
+ v3p3-supply = <&pm8916_l17>;
- internal-codec-playback-dai-link@0 {
- link-name = "WCD";
- cpu {
- sound-dai = <&lpass MI2S_PRIMARY>;
- };
- codec {
- sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
- };
- };
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+ pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+ #sound-dai-cells = <1>;
- internal-codec-capture-dai-link@0 {
- link-name = "WCD-Capture";
- cpu {
- sound-dai = <&lpass MI2S_TERTIARY>;
- };
- codec {
- sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7533_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
};
};
- };
- spmi@200f000 {
- pm8916@0 {
- gpios@c000 {
- gpio-line-names =
- "USR_LED_3_CTRL",
- "USR_LED_4_CTRL",
- "USB_HUB_RESET_N_PM",
- "USB_SW_SEL_PM";
- };
- mpps@a000 {
- gpio-line-names =
- "VDD_PX_BIAS",
- "WLAN_LED_CTRL",
- "BT_LED_CTRL",
- "GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
+ port@1 {
+ reg = <1>;
+ adv7533_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
};
};
};
-
- wcnss@a21b000 {
- status = "okay";
- };
-
- tpiu@820000 { status = "okay"; };
- funnel@821000 { status = "okay"; };
- replicator@824000 { status = "okay"; };
- etf@825000 { status = "okay"; };
- etr@826000 { status = "okay"; };
- funnel@841000 { status = "okay"; };
- debug@850000 { status = "okay"; };
- debug@852000 { status = "okay"; };
- debug@854000 { status = "okay"; };
- debug@856000 { status = "okay"; };
- etm@85c000 { status = "okay"; };
- etm@85d000 { status = "okay"; };
- etm@85e000 { status = "okay"; };
- etm@85f000 { status = "okay"; };
- cti@810000 { status = "okay"; };
- cti@811000 { status = "okay"; };
- cti@858000 { status = "okay"; };
- cti@859000 { status = "okay"; };
- cti@85a000 { status = "okay"; };
- cti@85b000 { status = "okay"; };
- };
-
- usb2513 {
- compatible = "smsc,usb3503";
- reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
- initial-mode = <1>;
- };
-
- usb_id: usb-id {
- compatible = "linux,extcon-usb-gpio";
- id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb_id_default>;
};
+};
- hdmi-out {
- compatible = "hdmi-connector";
- type = "a";
+&blsp_i2c6 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-I2C1";
+};
- port {
- hdmi_con: endpoint {
- remote-endpoint = <&adv7533_out>;
- };
- };
- };
+&blsp_spi3 {
+ /* On High speed expansion */
+ status = "okay";
+ label = "HS-SPI1";
+};
- gpio-keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- autorepeat;
+&blsp_spi5 {
+ /* On Low speed expansion */
+ status = "okay";
+ label = "LS-SPI0";
+};
- pinctrl-names = "default";
- pinctrl-0 = <&msm_key_volp_n_default>;
+&blsp1_uart1 {
+ status = "okay";
+ label = "LS-UART0";
+};
- button@0 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
- };
- };
+&blsp1_uart2 {
+ status = "okay";
+ label = "LS-UART1";
};
&camss {
- status = "ok";
+ status = "okay";
ports {
- #address-cells = <1>;
- #size-cells = <0>;
port@0 {
reg = <0>;
csiphy0_ep: endpoint {
@@ -602,7 +258,7 @@
};
&cci {
- status = "ok";
+ status = "okay";
};
&cci_i2c0 {
@@ -636,28 +292,126 @@
};
};
-&spmi_bus {
- pm8916_0: pm8916@0 {
- pon@800 {
- resin {
- compatible = "qcom,pm8941-resin";
- interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
- debounce = <15625>;
- bias-pull-up;
- linux,code = <KEY_VOLUMEDOWN>;
- };
+&dsi0_out {
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&adv7533_in>;
+};
+
+&lpass {
+ status = "okay";
+};
+
+&pm8916_resin {
+ status = "okay";
+ linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&pronto {
+ status = "okay";
+};
+
+&sdhc_1 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+ pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+ cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
+};
+
+&sound {
+ status = "okay";
+
+ pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
+ pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
+ pinctrl-names = "default", "sleep";
+ qcom,model = "DB410c";
+ qcom,audio-routing =
+ "AMIC2", "MIC BIAS Internal2",
+ "AMIC3", "MIC BIAS External1";
+
+ external-dai-link@0 {
+ link-name = "ADV7533";
+ cpu {
+ sound-dai = <&lpass MI2S_QUATERNARY>;
+ };
+ codec {
+ sound-dai = <&adv_bridge 0>;
+ };
+ };
+
+ internal-codec-playback-dai-link@0 {
+ link-name = "WCD";
+ cpu {
+ sound-dai = <&lpass MI2S_PRIMARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+ };
+ };
+
+ internal-codec-capture-dai-link@0 {
+ link-name = "WCD-Capture";
+ cpu {
+ sound-dai = <&lpass MI2S_TERTIARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
};
};
};
-&wcd_codec {
+&usb {
status = "okay";
+ extcon = <&usb_id>, <&usb_id>;
+
+ pinctrl-names = "default", "device";
+ pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
+ pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
+};
+
+&usb_hs_phy {
+ extcon = <&usb_id>;
+};
+
+&wcd_codec {
clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
clock-names = "mclk";
qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
};
+/* Enable CoreSight */
+&cti0 { status = "okay"; };
+&cti1 { status = "okay"; };
+&cti12 { status = "okay"; };
+&cti13 { status = "okay"; };
+&cti14 { status = "okay"; };
+&cti15 { status = "okay"; };
+&debug0 { status = "okay"; };
+&debug1 { status = "okay"; };
+&debug2 { status = "okay"; };
+&debug3 { status = "okay"; };
+&etf { status = "okay"; };
+&etm0 { status = "okay"; };
+&etm1 { status = "okay"; };
+&etm2 { status = "okay"; };
+&etm3 { status = "okay"; };
+&etr { status = "okay"; };
+&funnel0 { status = "okay"; };
+&funnel1 { status = "okay"; };
+&replicator { status = "okay"; };
+&tpiu { status = "okay"; };
+
&smd_rpm_regulators {
vdd_l1_l2_l3-supply = <&pm8916_s3>;
vdd_l4_l5_l6-supply = <&pm8916_s4>;
@@ -795,7 +549,155 @@
drive-strength = <16>;
};
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ * NC = not connected (pin out but not routed from the chip to
+ * anything the board)
+ * "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ * LSEC = Low Speed External Connector
+ * HSEC = High Speed External Connector
+ *
+ * Line names are taken from the schematic "DragonBoard410c"
+ * dated monday, august 31, 2015. Page 5 in particular.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART3. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+
&msmgpio {
+ gpio-line-names =
+ "[UART0_TX]", /* GPIO_0, LSEC pin 5 */
+ "[UART0_RX]", /* GPIO_1, LSEC pin 7 */
+ "[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
+ "[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
+ "[UART1_TX]", /* GPIO_4, LSEC pin 11 */
+ "[UART1_RX]", /* GPIO_5, LSEC pin 13 */
+ "[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
+ "[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
+ "[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
+ "[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
+ "[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
+ "[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
+ "GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
+ "GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
+ "[I2C3_SDA]", /* HSEC pin 38 */
+ "[I2C3_SCL]", /* HSEC pin 36 */
+ "[SPI0_MOSI]", /* LSEC pin 14 */
+ "[SPI0_MISO]", /* LSEC pin 10 */
+ "[SPI0_CS_N]", /* LSEC pin 12 */
+ "[SPI0_CLK]", /* LSEC pin 8 */
+ "HDMI_HPD_N", /* GPIO 20 */
+ "USR_LED_1_CTRL",
+ "[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
+ "[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
+ "GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
+ "GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
+ "[CSI0_MCLK]", /* HSEC pin 15 */
+ "[CSI1_MCLK]", /* HSEC pin 17 */
+ "GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
+ "[I2C2_SDA]", /* HSEC pin 34 */
+ "[I2C2_SCL]", /* HSEC pin 32 */
+ "DSI2HDMI_INT_N",
+ "DSI_SW_SEL_APQ",
+ "GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
+ "GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
+ "GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
+ "GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
+ "FORCED_USB_BOOT",
+ "SD_CARD_DET_N",
+ "[WCSS_BT_SSBI]",
+ "[WCSS_WLAN_DATA_2]", /* GPIO 40 */
+ "[WCSS_WLAN_DATA_1]",
+ "[WCSS_WLAN_DATA_0]",
+ "[WCSS_WLAN_SET]",
+ "[WCSS_WLAN_CLK]",
+ "[WCSS_FM_SSBI]",
+ "[WCSS_FM_SDI]",
+ "[WCSS_BT_DAT_CTL]",
+ "[WCSS_BT_DAT_STB]",
+ "NC",
+ "NC", /* GPIO 50 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO 60 */
+ "NC",
+ "NC",
+ "[CDC_PDM0_CLK]",
+ "[CDC_PDM0_SYNC]",
+ "[CDC_PDM0_TX0]",
+ "[CDC_PDM0_RX0]",
+ "[CDC_PDM0_RX1]",
+ "[CDC_PDM0_RX2]",
+ "GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
+ "NC", /* GPIO 70 */
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO 74 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "BOOT_CONFIG_0", /* GPIO 80 */
+ "BOOT_CONFIG_1",
+ "BOOT_CONFIG_2",
+ "BOOT_CONFIG_3",
+ "NC",
+ "NC",
+ "BOOT_CONFIG_5",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO 90 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO 100 */
+ "NC",
+ "NC",
+ "NC",
+ "SSBI_GPS",
+ "NC",
+ "NC",
+ "KEY_VOLP_N",
+ "NC",
+ "NC",
+ "[LS_EXP_MI2S_WS]", /* GPIO 110 */
+ "NC",
+ "NC",
+ "[LS_EXP_MI2S_SCK]",
+ "[LS_EXP_MI2S_DATA0]",
+ "GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
+ "NC",
+ "[DSI2HDMI_MI2S_WS]",
+ "[DSI2HDMI_MI2S_SCK]",
+ "[DSI2HDMI_MI2S_DATA0]",
+ "USR_LED_2_CTRL", /* GPIO 120 */
+ "SB_HS_ID";
+
msmgpio_leds: msmgpio-leds {
pins = "gpio21", "gpio120";
function = "gpio";
@@ -855,6 +757,12 @@
};
&pm8916_gpios {
+ gpio-line-names =
+ "USR_LED_3_CTRL",
+ "USR_LED_4_CTRL",
+ "USB_HUB_RESET_N_PM",
+ "USB_SW_SEL_PM";
+
usb_hub_reset_pm: usb-hub-reset-pm {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
@@ -897,6 +805,12 @@
};
&pm8916_mpps {
+ gpio-line-names =
+ "VDD_PX_BIAS",
+ "WLAN_LED_CTRL",
+ "BT_LED_CTRL",
+ "GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
+
pinctrl-names = "default";
pinctrl-0 = <&ls_exp_gpio_f>;