diff options
Diffstat (limited to 'arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts')
-rw-r--r-- | arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts | 377 |
1 files changed, 358 insertions, 19 deletions
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts index 8f456146409f..5084ddcee00f 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts @@ -2,16 +2,19 @@ /* * dts file for Xilinx ZynqMP ZCU104 * - * (C) Copyright 2017 - 2018, Xilinx, Inc. + * (C) Copyright 2017 - 2022, Xilinx, Inc. + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. * - * Michal Simek <michal.simek@xilinx.com> + * Michal Simek <michal.simek@amd.com> */ /dts-v1/; #include "zynqmp.dtsi" -#include "zynqmp-clk.dtsi" +#include "zynqmp-clk-ccf.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/pinctrl-zynqmp.h> +#include <dt-bindings/phy/phy.h> / { model = "ZynqMP ZCU104 RevA"; @@ -21,10 +24,13 @@ ethernet0 = &gem3; i2c0 = &i2c1; mmc0 = &sdhci1; + nvmem0 = &eeprom; rtc0 = &rtc; serial0 = &uart0; serial1 = &uart1; serial2 = &dcc; + spi0 = &qspi; + usb0 = &usb0; }; chosen { @@ -36,26 +42,87 @@ device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; + + clock_8t49n287_5: clk125 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + }; + + clock_8t49n287_2: clk26 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + clock_8t49n287_3: clk27 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; }; &can1 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1_default>; }; &dcc { status = "okay"; }; +&fpd_dma_chan1 { + status = "okay"; +}; + +&fpd_dma_chan2 { + status = "okay"; +}; + +&fpd_dma_chan3 { + status = "okay"; +}; + +&fpd_dma_chan4 { + status = "okay"; +}; + +&fpd_dma_chan5 { + status = "okay"; +}; + +&fpd_dma_chan6 { + status = "okay"; +}; + +&fpd_dma_chan7 { + status = "okay"; +}; + +&fpd_dma_chan8 { + status = "okay"; +}; + &gem3 { status = "okay"; phy-handle = <&phy0>; phy-mode = "rgmii-id"; - phy0: phy@c { - reg = <0xc>; - ti,rx-internal-delay = <0x8>; - ti,tx-internal-delay = <0xa>; - ti,fifo-depth = <0x1>; - ti,dp83867-rxctrl-strap-quirk; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gem3_default>; + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@c { + #phy-cells = <1>; + compatible = "ethernet-phy-id2000.a231"; + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; + }; }; }; @@ -63,9 +130,18 @@ status = "okay"; }; +&gpu { + status = "okay"; +}; + &i2c1 { status = "okay"; clock-frequency = <400000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1_default>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; /* Another connection to this bus via PL i2c via PCA9306 - u45 */ i2c-mux@74 { /* u34 */ @@ -85,7 +161,7 @@ * 512B - 768B address 0x56 * 768B - 1024B address 0x57 */ - eeprom@54 { /* u23 */ + eeprom: eeprom@54 { /* u23 */ compatible = "atmel,24c08"; reg = <0x54>; #address-cells = <1>; @@ -97,20 +173,20 @@ #address-cells = <1>; #size-cells = <0>; reg = <1>; - clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */ - reg = <0x6c>; - }; + /* 8T49N287 - u182 */ }; i2c@2 { #address-cells = <1>; #size-cells = <0>; reg = <2>; - irps5401_43: irps54012@43 { /* IRPS5401 - u175 */ - reg = <0x43>; + irps5401_43: irps5401@43 { /* IRPS5401 - u175 */ + compatible = "infineon,irps5401"; + reg = <0x43>; /* pmbus / i2c 0x13 */ }; - irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */ - reg = <0x4d>; + irps5401_44: irps5401@44 { /* IRPS5401 - u180 */ + compatible = "infineon,irps5401"; + reg = <0x44>; /* pmbus / i2c 0x14 */ }; }; @@ -118,9 +194,9 @@ #address-cells = <1>; #size-cells = <0>; reg = <4>; - tca6416_u97: gpio@21 { + tca6416_u97: gpio@20 { compatible = "ti,tca6416"; - reg = <0x21>; + reg = <0x20>; gpio-controller; #gpio-cells = <2>; /* @@ -154,6 +230,226 @@ }; }; +&pinctrl0 { + status = "okay"; + + pinctrl_can1_default: can1-default { + mux { + function = "can1"; + groups = "can1_6_grp"; + }; + + conf { + groups = "can1_6_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO25"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO24"; + bias-disable; + }; + }; + + pinctrl_i2c1_default: i2c1-default { + mux { + groups = "i2c1_4_grp"; + function = "i2c1"; + }; + + conf { + groups = "i2c1_4_grp"; + bias-pull-up; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + }; + + pinctrl_i2c1_gpio: i2c1-gpio { + mux { + groups = "gpio0_16_grp", "gpio0_17_grp"; + function = "gpio0"; + }; + + conf { + groups = "gpio0_16_grp", "gpio0_17_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + }; + + pinctrl_gem3_default: gem3-default { + mux { + function = "ethernet3"; + groups = "ethernet3_0_grp"; + }; + + conf { + groups = "ethernet3_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74", + "MIO75"; + bias-high-impedance; + low-power-disable; + }; + + conf-tx { + pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68", + "MIO69"; + bias-disable; + low-power-enable; + }; + + mux-mdio { + function = "mdio3"; + groups = "mdio3_0_grp"; + }; + + conf-mdio { + groups = "mdio3_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + bias-disable; + }; + }; + + pinctrl_sdhci1_default: sdhci1-default { + mux { + groups = "sdio1_0_grp"; + function = "sdio1"; + }; + + conf { + groups = "sdio1_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + bias-disable; + drive-strength = <12>; + }; + + mux-cd { + groups = "sdio1_cd_0_grp"; + function = "sdio1_cd"; + }; + + conf-cd { + groups = "sdio1_cd_0_grp"; + bias-high-impedance; + bias-pull-up; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + }; + + pinctrl_uart0_default: uart0-default { + mux { + groups = "uart0_4_grp"; + function = "uart0"; + }; + + conf { + groups = "uart0_4_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO18"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO19"; + bias-disable; + }; + }; + + pinctrl_uart1_default: uart1-default { + mux { + groups = "uart1_5_grp"; + function = "uart1"; + }; + + conf { + groups = "uart1_5_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + drive-strength = <12>; + }; + + conf-rx { + pins = "MIO21"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO20"; + bias-disable; + }; + }; + + pinctrl_usb0_default: usb0-default { + mux { + groups = "usb0_0_grp"; + function = "usb0"; + }; + + conf { + groups = "usb0_0_grp"; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + conf-rx { + pins = "MIO52", "MIO53", "MIO55"; + bias-high-impedance; + drive-strength = <12>; + slew-rate = <SLEW_RATE_FAST>; + }; + + conf-tx { + pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", + "MIO60", "MIO61", "MIO62", "MIO63"; + bias-disable; + drive-strength = <4>; + slew-rate = <SLEW_RATE_SLOW>; + }; + }; +}; + +&psgtr { + status = "okay"; + /* nc, sata, usb3, dp */ + clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>; + clock-names = "ref1", "ref2", "ref3"; +}; + +&qspi { + status = "okay"; + flash@0 { + compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */ + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; /* Based on DC1 spec */ + }; +}; + &rtc { status = "okay"; }; @@ -169,28 +465,71 @@ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ &sdhci1 { status = "okay"; no-1-8-v; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhci1_default>; + xlnx,mio-bank = <1>; disable-wp; }; &uart0 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0_default>; }; &uart1 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_default>; }; /* ULPI SMSC USB3320 */ &usb0 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0_default>; + phy-names = "usb3-phy"; + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>; +}; + +&dwc3_0 { + status = "okay"; + dr_mode = "host"; + snps,usb3_lpm_capable; + maximum-speed = "super-speed"; }; &watchdog0 { status = "okay"; }; + +&xilinx_ams { + status = "okay"; +}; + +&ams_ps { + status = "okay"; +}; + +&ams_pl { + status = "okay"; +}; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 3>, + <&psgtr 0 PHY_TYPE_DP 1 3>; +}; |