diff options
Diffstat (limited to 'arch/arm64')
62 files changed, 3754 insertions, 424 deletions
diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig index 69c8787bec7d..bc3f00f586f1 100644 --- a/arch/arm64/Kconfig +++ b/arch/arm64/Kconfig @@ -54,6 +54,7 @@ config ARM64 select HAVE_ALIGNED_STRUCT_PAGE if SLUB select HAVE_ARCH_AUDITSYSCALL select HAVE_ARCH_BITREVERSE + select HAVE_ARCH_HARDENED_USERCOPY select HAVE_ARCH_HUGE_VMAP select HAVE_ARCH_JUMP_LABEL select HAVE_ARCH_KASAN if SPARSEMEM_VMEMMAP && !(ARM64_16K_PAGES && ARM64_VA_BITS_48) diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms index bb2616b16157..7c5a036a9e76 100644 --- a/arch/arm64/Kconfig.platforms +++ b/arch/arm64/Kconfig.platforms @@ -8,7 +8,7 @@ config ARCH_SUNXI config ARCH_ALPINE bool "Annapurna Labs Alpine platform" - select ALPINE_MSI + select ALPINE_MSI if PCI help This enables support for the Annapurna Labs Alpine Soc family. @@ -66,7 +66,7 @@ config ARCH_LG1K config ARCH_HISI bool "Hisilicon SoC Family" select ARM_TIMER_SP804 - select HISILICON_IRQ_MBIGEN + select HISILICON_IRQ_MBIGEN if PCI help This enables support for Hisilicon ARMv8 SoC family @@ -161,6 +161,8 @@ config ARCH_TEGRA select GENERIC_CLOCKEVENTS select HAVE_CLK select PINCTRL + select PM + select PM_GENERIC_DOMAINS select RESET_CONTROLLER help This enables support for the NVIDIA Tegra SoC family. diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi index d4a12fad8afd..d95dc408629a 100644 --- a/arch/arm64/boot/dts/broadcom/ns2.dtsi +++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi @@ -299,6 +299,14 @@ }; }; + pwm: pwm@66010000 { + compatible = "brcm,iproc-pwm"; + reg = <0x66010000 0x28>; + clocks = <&osc>; + #pwm-cells = <3>; + status = "disabled"; + }; + mdio_mux_iproc: mdio-mux@6602023c { compatible = "brcm,mdio-mux-iproc"; reg = <0x6602023c 0x14>; diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts index 299f3ce969ab..c528dd52ba2d 100644 --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts @@ -12,6 +12,7 @@ /dts-v1/; #include "exynos7.dtsi" #include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/clock/samsung,s2mps11.h> / { model = "Samsung Exynos7 Espresso board based on EXYNOS7"; @@ -43,6 +44,8 @@ &rtc { status = "okay"; + clocks = <&clock_ccore PCLK_RTC>, <&s2mps15_osc S2MPS11_CLK_AP>; + clock-names = "rtc", "rtc_src"; }; &watchdog { diff --git a/arch/arm64/boot/dts/exynos/exynos7.dtsi b/arch/arm64/boot/dts/exynos/exynos7.dtsi index 162831546e18..6328a66ed97e 100644 --- a/arch/arm64/boot/dts/exynos/exynos7.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos7.dtsi @@ -10,6 +10,7 @@ */ #include <dt-bindings/clock/exynos7-clk.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> / { compatible = "samsung,exynos7"; @@ -473,10 +474,14 @@ timer { compatible = "arm,armv8-timer"; - interrupts = <1 13 0xff08>, - <1 14 0xff08>, - <1 11 0xff08>, - <1 10 0xff08>; + interrupts = <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; }; pmu_system_controller: system-controller@105c0000 { diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts index 9d3e9fe1c87c..dd9e91941df4 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts @@ -56,12 +56,14 @@ gpio1 = &gpio2; gpio2 = &gpio3; gpio3 = &gpio4; - serial0 = &lpuart0; - serial1 = &lpuart1; - serial2 = &lpuart2; - serial3 = &lpuart3; - serial4 = &lpuart4; - serial5 = &lpuart5; + serial0 = &duart0; + serial1 = &duart1; + serial2 = &duart2; + serial3 = &duart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; }; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts index 40846319be69..d2313e05fd22 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts @@ -52,6 +52,14 @@ aliases { crypto = &crypto; + serial0 = &duart0; + serial1 = &duart1; + serial2 = &duart2; + serial3 = &duart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; }; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi index a67e210e2019..58635f7f4668 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi @@ -247,6 +247,13 @@ bus-width = <4>; }; + ddr: memory-controller@1080000 { + compatible = "fsl,qoriq-memory-controller"; + reg = <0x0 0x1080000 0x0 0x1000>; + interrupts = <0 144 0x4>; + big-endian; + }; + dspi0: dspi@2100000 { compatible = "fsl,ls1043a-dspi", "fsl,ls1021a-v1.0-dspi"; #address-cells = <1>; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts index e8801faca996..b0dd010979e7 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts @@ -57,6 +57,9 @@ serial1 = &serial1; }; + chosen { + stdout-path = "serial0:115200n8"; + }; }; &esdhc { diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts index e127f0baab19..ad0ebb8a1949 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts @@ -56,6 +56,10 @@ serial0 = &serial0; serial1 = &serial1; }; + + chosen { + stdout-path = "serial1:115200n8"; + }; }; &esdhc { diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi index e3b6034ea5d9..d1059765dfee 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi @@ -588,6 +588,7 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; num-lanes = <4>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x10 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -612,6 +613,7 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; num-lanes = <4>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x12 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -636,6 +638,7 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; num-lanes = <8>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x14 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -660,6 +663,7 @@ #address-cells = <3>; #size-cells = <2>; device_type = "pci"; + dma-coherent; num-lanes = <4>; bus-range = <0x0 0xff>; ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000 /* downstream I/O */ @@ -715,4 +719,18 @@ interrupts = <0 12 4>; }; }; + + ddr1: memory-controller@1080000 { + compatible = "fsl,qoriq-memory-controller"; + reg = <0x0 0x1080000 0x0 0x1000>; + interrupts = <0 17 0x4>; + little-endian; + }; + + ddr2: memory-controller@1090000 { + compatible = "fsl,qoriq-memory-controller"; + reg = <0x0 0x1090000 0x0 0x1000>; + interrupts = <0 18 0x4>; + little-endian; + }; }; diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts index 593c7e43de79..dba3c131c62c 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts +++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts @@ -29,16 +29,56 @@ * Reserve below regions from memory node: * * 0x05e0,0000 - 0x05ef,ffff: MCU firmware runtime using + * 0x05f0,1000 - 0x05f0,1fff: Reboot reason * 0x06df,f000 - 0x06df,ffff: Mailbox message data * 0x0740,f000 - 0x0740,ffff: MCU firmware section + * 0x21f0,0000 - 0x21ff,ffff: pstore/ramoops buffer * 0x3e00,0000 - 0x3fff,ffff: OP-TEE */ memory@0 { device_type = "memory"; reg = <0x00000000 0x00000000 0x00000000 0x05e00000>, - <0x00000000 0x05f00000 0x00000000 0x00eff000>, + <0x00000000 0x05f00000 0x00000000 0x00001000>, + <0x00000000 0x05f02000 0x00000000 0x00efd000>, <0x00000000 0x06e00000 0x00000000 0x0060f000>, - <0x00000000 0x07410000 0x00000000 0x36bf0000>; + <0x00000000 0x07410000 0x00000000 0x1aaf0000>, + <0x00000000 0x22000000 0x00000000 0x1c000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ramoops@0x21f00000 { + compatible = "ramoops"; + reg = <0x0 0x21f00000 0x0 0x00100000>; + record-size = <0x00020000>; + console-size = <0x00020000>; + ftrace-size = <0x00020000>; + }; + + /* global autoconfigured region for contiguous allocations */ + linux,cma { + compatible = "shared-dma-pool"; + reusable; + size = <0x00000000 0x08000000>; + linux,cma-default; + }; + }; + + reboot-mode-syscon@5f01000 { + compatible = "syscon", "simple-mfd"; + reg = <0x0 0x05f01000 0x0 0x00001000>; + + reboot-mode { + compatible = "syscon-reboot-mode"; + offset = <0x0>; + + mode-normal = <0x77665501>; + mode-bootloader = <0x77665500>; + mode-recovery = <0x77665502>; + }; }; soc { @@ -55,6 +95,8 @@ }; uart1: uart@f7111000 { + assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>; + assigned-clock-rates = <150000000>; status = "ok"; }; @@ -372,3 +414,43 @@ &uart3 { label = "LS-UART1"; }; + +&ade { + status = "ok"; +}; + +&dsi { + status = "ok"; + + ports { + /* 1 for output port */ + port@1 { + reg = <1>; + + dsi_out0: endpoint@0 { + remote-endpoint = <&adv7533_in>; + }; + }; + }; +}; + +&i2c2 { + #address-cells = <1>; + #size-cells = <0>; + status = "ok"; + + adv7533: adv7533@39 { + compatible = "adi,adv7533"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <1 2>; + pd-gpio = <&gpio0 4 0>; + adi,dsi-lanes = <4>; + + port { + adv7533_in: endpoint { + remote-endpoint = <&dsi_out0>; + }; + }; + }; +}; diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi index 4f270410a5cb..17839db585d5 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi @@ -262,6 +262,11 @@ #clock-cells = <1>; }; + medianoc_ade: medianoc_ade@f4520000 { + compatible = "syscon"; + reg = <0x0 0xf4520000 0x0 0x4000>; + }; + stub_clock: stub_clock { compatible = "hisilicon,hi6220-stub-clk"; hisilicon,hi6220-clk-sram = <&sram>; @@ -766,6 +771,7 @@ interrupts = <0x0 0x48 0x4>; clocks = <&sys_ctrl 2>, <&sys_ctrl 1>; clock-names = "ciu", "biu"; + resets = <&sys_ctrl PERIPH_RSTDIS0_MMC0>; bus-width = <0x8>; vmmc-supply = <&ldo19>; pinctrl-names = "default"; @@ -779,12 +785,16 @@ card-detect-delay = <200>; hisilicon,peripheral-syscon = <&ao_ctrl>; cap-sd-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; reg = <0x0 0xf723e000 0x0 0x1000>; interrupts = <0x0 0x49 0x4>; #address-cells = <0x1>; #size-cells = <0x0>; clocks = <&sys_ctrl 4>, <&sys_ctrl 3>; clock-names = "ciu", "biu"; + resets = <&sys_ctrl PERIPH_RSTDIS0_MMC1>; vqmmc-supply = <&ldo7>; vmmc-supply = <&ldo10>; bus-width = <0x4>; @@ -802,6 +812,7 @@ interrupts = <0x0 0x4a 0x4>; clocks = <&sys_ctrl HI6220_MMC2_CIUCLK>, <&sys_ctrl HI6220_MMC2_CLK>; clock-names = "ciu", "biu"; + resets = <&sys_ctrl PERIPH_RSTDIS0_MMC2>; bus-width = <0x4>; broken-cd; pinctrl-names = "default", "idle"; @@ -850,5 +861,55 @@ }; }; }; + + ade: ade@f4100000 { + compatible = "hisilicon,hi6220-ade"; + reg = <0x0 0xf4100000 0x0 0x7800>; + reg-names = "ade_base"; + hisilicon,noc-syscon = <&medianoc_ade>; + resets = <&media_ctrl MEDIA_ADE>; + interrupts = <0 115 4>; /* ldi interrupt */ + + clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>, + <&media_ctrl HI6220_ADE_PIX_SRC>; + /*clock name*/ + clock-names = "clk_ade_core", + "clk_codec_jpeg", + "clk_ade_pix"; + + assigned-clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>; + assigned-clock-rates = <360000000>, <288000000>; + dma-coherent; + status = "disabled"; + + port { + ade_out: endpoint { + remote-endpoint = <&dsi_in>; + }; + }; + }; + + dsi: dsi@f4107800 { + compatible = "hisilicon,hi6220-dsi"; + reg = <0x0 0xf4107800 0x0 0x100>; + clocks = <&media_ctrl HI6220_DSI_PCLK>; + clock-names = "pclk"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 0 for input port */ + port@0 { + reg = <0>; + dsi_in: endpoint { + remote-endpoint = <&ade_out>; + }; + }; + }; + }; }; }; diff --git a/arch/arm64/boot/dts/hisilicon/hip05.dtsi b/arch/arm64/boot/dts/hisilicon/hip05.dtsi index bf322ed038b8..4b472a302cd8 100644 --- a/arch/arm64/boot/dts/hisilicon/hip05.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip05.dtsi @@ -300,11 +300,6 @@ clock-frequency = <200000000>; }; - peri_c_subctrl: syscon@80000000 { - compatible = "hisilicon,hip05-perisubc", "syscon"; - reg = < 0x0 0x80000000 0x0 0x10000>; - }; - uart0: uart@80300000 { compatible = "snps,dw-apb-uart"; reg = <0x0 0x80300000 0x0 0x10000>; diff --git a/arch/arm64/boot/dts/hisilicon/hip05_hns.dtsi b/arch/arm64/boot/dts/hisilicon/hip05_hns.dtsi deleted file mode 100644 index b6a130c2e5a4..000000000000 --- a/arch/arm64/boot/dts/hisilicon/hip05_hns.dtsi +++ /dev/null @@ -1,180 +0,0 @@ -soc0: soc@000000000 { - #address-cells = <2>; - #size-cells = <2>; - device_type = "soc"; - compatible = "simple-bus"; - ranges = <0x0 0x0 0x0 0x0 0x1 0x0>; - chip-id = <0>; - - soc0_mdio0: mdio@803c0000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "hisilicon,hns-mdio"; - reg = <0x0 0x803c0000 0x0 0x10000>; - subctrl-vbase = <&peri_c_subctrl>; - - soc0_phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "ethernet-phy-ieee802.3-c22"; - }; - soc0_phy1: ethernet-phy@1 { - reg = <0x1>; - compatible = "ethernet-phy-ieee802.3-c22"; - }; - }; - - dsaf0: dsa@c7000000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "hisilicon,hns-dsaf-v1"; - mode = "6port-16rss"; - interrupt-parent = <&mbigen_dsa>; - - reg = <0x0 0xc5000000 0x0 0x890000 - 0x0 0xc7000000 0x0 0x60000 - >; - - reg-names = "ppe-base","dsaf-base"; - subctrl-syscon = <&dsaf_subctrl>; - reset-field-offset = <0>; - interrupts = < - /* [14] ge fifo err 8 / xge 6**/ - 149 0x4 150 0x4 151 0x4 152 0x4 - 153 0x4 154 0x4 26 0x4 27 0x4 - 155 0x4 156 0x4 157 0x4 158 0x4 159 0x4 160 0x4 - /* [12] rcb com 4*3**/ - 0x6 0x4 0x7 0x4 0x8 0x4 0x9 0x4 - 16 0x4 17 0x4 18 0x4 19 0x4 - 22 0x4 23 0x4 24 0x4 25 0x4 - /* [8] ppe tnl 0-7***/ - 0x0 0x4 0x1 0x4 0x2 0x4 0x3 0x4 - 0x4 0x4 0x5 0x4 12 0x4 13 0x4 - /* [21] dsaf event int 3+18**/ - 128 0x4 129 0x4 130 0x4 - 0x83 0x4 0x84 0x4 0x85 0x4 0x86 0x4 0x87 0x4 0x88 0x4 - 0x89 0x4 0x8a 0x4 0x8b 0x4 0x8c 0x4 0x8d 0x4 0x8e 0x4 - 0x8f 0x4 0x90 0x4 0x91 0x4 0x92 0x4 0x93 0x4 0x94 0x4 - /* [4] debug rcb 2*2*/ - 0xe 0x1 0xf 0x1 0x14 0x1 0x15 0x1 - /* [256] sevice rcb 2*128*/ - 0x180 0x1 0x181 0x1 0x182 0x1 0x183 0x1 - 0x184 0x1 0x185 0x1 0x186 0x1 0x187 0x1 - 0x188 0x1 0x189 0x1 0x18a 0x1 0x18b 0x1 - 0x18c 0x1 0x18d 0x1 0x18e 0x1 0x18f 0x1 - 0x190 0x1 0x191 0x1 0x192 0x1 0x193 0x1 - 0x194 0x1 0x195 0x1 0x196 0x1 0x197 0x1 - 0x198 0x1 0x199 0x1 0x19a 0x1 0x19b 0x1 - 0x19c 0x1 0x19d 0x1 0x19e 0x1 0x19f 0x1 - 0x1a0 0x1 0x1a1 0x1 0x1a2 0x1 0x1a3 0x1 - 0x1a4 0x1 0x1a5 0x1 0x1a6 0x1 0x1a7 0x1 - 0x1a8 0x1 0x1a9 0x1 0x1aa 0x1 0x1ab 0x1 - 0x1ac 0x1 0x1ad 0x1 0x1ae 0x1 0x1af 0x1 - 0x1b0 0x1 0x1b1 0x1 0x1b2 0x1 0x1b3 0x1 - 0x1b4 0x1 0x1b5 0x1 0x1b6 0x1 0x1b7 0x1 - 0x1b8 0x1 0x1b9 0x1 0x1ba 0x1 0x1bb 0x1 - 0x1bc 0x1 0x1bd 0x1 0x1be 0x1 0x1bf 0x1 - 0x1c0 0x1 0x1c1 0x1 0x1c2 0x1 0x1c3 0x1 - 0x1c4 0x1 0x1c5 0x1 0x1c6 0x1 0x1c7 0x1 - 0x1c8 0x1 0x1c9 0x1 0x1ca 0x1 0x1cb 0x1 - 0x1cc 0x1 0x1cd 0x1 0x1ce 0x1 0x1cf 0x1 - 0x1d0 0x1 0x1d1 0x1 0x1d2 0x1 0x1d3 0x1 - 0x1d4 0x1 0x1d5 0x1 0x1d6 0x1 0x1d7 0x1 - 0x1d8 0x1 0x1d9 0x1 0x1da 0x1 0x1db 0x1 - 0x1dc 0x1 0x1dd 0x1 0x1de 0x1 0x1df 0x1 - 0x1e0 0x1 0x1e1 0x1 0x1e2 0x1 0x1e3 0x1 - 0x1e4 0x1 0x1e5 0x1 0x1e6 0x1 0x1e7 0x1 - 0x1e8 0x1 0x1e9 0x1 0x1ea 0x1 0x1eb 0x1 - 0x1ec 0x1 0x1ed 0x1 0x1ee 0x1 0x1ef 0x1 - 0x1f0 0x1 0x1f1 0x1 0x1f2 0x1 0x1f3 0x1 - 0x1f4 0x1 0x1f5 0x1 0x1f6 0x1 0x1f7 0x1 - 0x1f8 0x1 0x1f9 0x1 0x1fa 0x1 0x1fb 0x1 - 0x1fc 0x1 0x1fd 0x1 0x1fe 0x1 0x1ff 0x1 - 0x200 0x1 0x201 0x1 0x202 0x1 0x203 0x1 - 0x204 0x1 0x205 0x1 0x206 0x1 0x207 0x1 - 0x208 0x1 0x209 0x1 0x20a 0x1 0x20b 0x1 - 0x20c 0x1 0x20d 0x1 0x20e 0x1 0x20f 0x1 - 0x210 0x1 0x211 0x1 0x212 0x1 0x213 0x1 - 0x214 0x1 0x215 0x1 0x216 0x1 0x217 0x1 - 0x218 0x1 0x219 0x1 0x21a 0x1 0x21b 0x1 - 0x21c 0x1 0x21d 0x1 0x21e 0x1 0x21f 0x1 - 0x220 0x1 0x221 0x1 0x222 0x1 0x223 0x1 - 0x224 0x1 0x225 0x1 0x226 0x1 0x227 0x1 - 0x228 0x1 0x229 0x1 0x22a 0x1 0x22b 0x1 - 0x22c 0x1 0x22d 0x1 0x22e 0x1 0x22f 0x1 - 0x230 0x1 0x231 0x1 0x232 0x1 0x233 0x1 - 0x234 0x1 0x235 0x1 0x236 0x1 0x237 0x1 - 0x238 0x1 0x239 0x1 0x23a 0x1 0x23b 0x1 - 0x23c 0x1 0x23d 0x1 0x23e 0x1 0x23f 0x1 - 0x240 0x1 0x241 0x1 0x242 0x1 0x243 0x1 - 0x244 0x1 0x245 0x1 0x246 0x1 0x247 0x1 - 0x248 0x1 0x249 0x1 0x24a 0x1 0x24b 0x1 - 0x24c 0x1 0x24d 0x1 0x24e 0x1 0x24f 0x1 - 0x250 0x1 0x251 0x1 0x252 0x1 0x253 0x1 - 0x254 0x1 0x255 0x1 0x256 0x1 0x257 0x1 - 0x258 0x1 0x259 0x1 0x25a 0x1 0x25b 0x1 - 0x25c 0x1 0x25d 0x1 0x25e 0x1 0x25f 0x1 - 0x260 0x1 0x261 0x1 0x262 0x1 0x263 0x1 - 0x264 0x1 0x265 0x1 0x266 0x1 0x267 0x1 - 0x268 0x1 0x269 0x1 0x26a 0x1 0x26b 0x1 - 0x26c 0x1 0x26d 0x1 0x26e 0x1 0x26f 0x1 - 0x270 0x1 0x271 0x1 0x272 0x1 0x273 0x1 - 0x274 0x1 0x275 0x1 0x276 0x1 0x277 0x1 - 0x278 0x1 0x279 0x1 0x27a 0x1 0x27b 0x1 - 0x27c 0x1 0x27d 0x1 0x27e 0x1 0x27f 0x1>; - buf-size = <4096>; - desc-num = <1024>; - dma-coherent; - - port@0 { - reg = <0>; - serdes-syscon = <&serdes_ctrl0>; - }; - port@1 { - reg = <1>; - serdes-syscon = <&serdes_ctrl0>; - }; - port@4 { - reg = <4>; - phy-handle = <&soc0_phy0>; - serdes-syscon = <&serdes_ctrl1>; - }; - port@5 { - reg = <5>; - phy-handle = <&soc0_phy1>; - serdes-syscon = <&serdes_ctrl1>; - }; - }; - - eth0: ethernet@0{ - compatible = "hisilicon,hns-nic-v1"; - ae-handle = <&dsaf0>; - port-idx-in-ae = <0>; - local-mac-address = [00 00 00 01 00 58]; - status = "disabled"; - dma-coherent; - }; - eth1: ethernet@1{ - compatible = "hisilicon,hns-nic-v1"; - ae-handle = <&dsaf0>; - port-idx-in-ae = <1>; - local-mac-address = [00 00 00 01 00 59]; - status = "disabled"; - dma-coherent; - }; - eth2: ethernet@4{ - compatible = "hisilicon,hns-nic-v1"; - ae-handle = <&dsaf0>; - port-idx-in-ae = <4>; - local-mac-address = [00 00 00 01 00 5a]; - status = "disabled"; - dma-coherent; - }; - eth3: ethernet@5{ - compatible = "hisilicon,hns-nic-v1"; - ae-handle = <&dsaf0>; - port-idx-in-ae = <5>; - local-mac-address = [00 00 00 01 00 5b]; - status = "disabled"; - dma-coherent; - }; -}; diff --git a/arch/arm64/boot/dts/hisilicon/hip06-d03.dts b/arch/arm64/boot/dts/hisilicon/hip06-d03.dts index f3e5323e430b..f54b28359607 100644 --- a/arch/arm64/boot/dts/hisilicon/hip06-d03.dts +++ b/arch/arm64/boot/dts/hisilicon/hip06-d03.dts @@ -25,6 +25,34 @@ chosen { }; }; +ð0 { + status = "ok"; +}; + +ð1 { + status = "ok"; +}; + +ð2 { + status = "ok"; +}; + +ð3 { + status = "ok"; +}; + +&sas0 { + status = "ok"; +}; + +&sas1 { + status = "ok"; +}; + +&sas2 { + status = "ok"; +}; + &usb_ohci { status = "ok"; }; diff --git a/arch/arm64/boot/dts/hisilicon/hip06.dtsi b/arch/arm64/boot/dts/hisilicon/hip06.dtsi index 5927bc472f1b..b548763366dd 100644 --- a/arch/arm64/boot/dts/hisilicon/hip06.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip06.dtsi @@ -277,6 +277,39 @@ #interrupt-cells = <2>; num-pins = <2>; }; + + mbigen_sas1: intc_sas1 { + msi-parent = <&its_dsa 0x40000>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <128>; + }; + + mbigen_sas2: intc_sas2 { + msi-parent = <&its_dsa 0x40040>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <128>; + }; + }; + + mbigen_dsa@c0080000 { + compatible = "hisilicon,mbigen-v2"; + reg = <0x0 0xc0080000 0x0 0x10000>; + + mbigen_dsaf0: intc_dsaf0 { + msi-parent = <&its_dsa 0x40800>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <409>; + }; + + mbigen_sas0: intc-sas0 { + msi-parent = <&its_dsa 0x40900>; + interrupt-controller; + #interrupt-cells = <2>; + num-pins = <128>; + }; }; soc { @@ -302,6 +335,338 @@ dma-coherent; status = "disabled"; }; + + peri_c_subctrl: sub_ctrl_c@60000000 { + compatible = "hisilicon,peri-subctrl","syscon"; + reg = <0 0x60000000 0x0 0x10000>; + }; + + dsa_subctrl: dsa_subctrl@c0000000 { + compatible = "hisilicon,dsa-subctrl", "syscon"; + reg = <0x0 0xc0000000 0x0 0x10000>; + }; + + pcie_subctl: pcie_subctl@a0000000 { + compatible = "hisilicon,pcie-sas-subctrl", "syscon"; + reg = <0x0 0xa0000000 0x0 0x10000>; + }; + + serdes_ctrl: sds_ctrl@c2200000 { + compatible = "syscon"; + reg = <0 0xc2200000 0x0 0x80000>; + }; + + mdio@603c0000 { + compatible = "hisilicon,hns-mdio"; + reg = <0x0 0x603c0000 0x0 0x1000>; + subctrl-vbase = <&peri_c_subctrl 0x338 0xa38 0x531c 0x5a1c>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; + + dsaf0: dsa@c7000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "hisilicon,hns-dsaf-v2"; + mode = "6port-16rss"; + reg = <0x0 0xc5000000 0x0 0x890000 + 0x0 0xc7000000 0x0 0x600000>; + reg-names = "ppe-base", "dsaf-base"; + interrupt-parent = <&mbigen_dsaf0>; + subctrl-syscon = <&dsa_subctrl>; + reset-field-offset = <0>; + interrupts = + <576 1>, <577 1>, <578 1>, <579 1>, <580 1>, + <581 1>, <582 1>, <583 1>, <584 1>, <585 1>, + <586 1>, <587 1>, <588 1>, <589 1>, <590 1>, + <591 1>, <592 1>, <593 1>, <594 1>, <595 1>, + <596 1>, <597 1>, <598 1>, <599 1>, <600 1>, + <960 1>, <961 1>, <962 1>, <963 1>, <964 1>, + <965 1>, <966 1>, <967 1>, <968 1>, <969 1>, + <970 1>, <971 1>, <972 1>, <973 1>, <974 1>, + <975 1>, <976 1>, <977 1>, <978 1>, <979 1>, + <980 1>, <981 1>, <982 1>, <983 1>, <984 1>, + <985 1>, <986 1>, <987 1>, <988 1>, <989 1>, + <990 1>, <991 1>, <992 1>, <993 1>, <994 1>, + <995 1>, <996 1>, <997 1>, <998 1>, <999 1>, + <1000 1>, <1001 1>, <1002 1>, <1003 1>, <1004 1>, + <1005 1>, <1006 1>, <1007 1>, <1008 1>, <1009 1>, + <1010 1>, <1011 1>, <1012 1>, <1013 1>, <1014 1>, + <1015 1>, <1016 1>, <1017 1>, <1018 1>, <1019 1>, + <1020 1>, <1021 1>, <1022 1>, <1023 1>, <1024 1>, + <1025 1>, <1026 1>, <1027 1>, <1028 1>, <1029 1>, + <1030 1>, <1031 1>, <1032 1>, <1033 1>, <1034 1>, + <1035 1>, <1036 1>, <1037 1>, <1038 1>, <1039 1>, + <1040 1>, <1041 1>, <1042 1>, <1043 1>, <1044 1>, + <1045 1>, <1046 1>, <1047 1>, <1048 1>, <1049 1>, + <1050 1>, <1051 1>, <1052 1>, <1053 1>, <1054 1>, + <1055 1>, <1056 1>, <1057 1>, <1058 1>, <1059 1>, + <1060 1>, <1061 1>, <1062 1>, <1063 1>, <1064 1>, + <1065 1>, <1066 1>, <1067 1>, <1068 1>, <1069 1>, + <1070 1>, <1071 1>, <1072 1>, <1073 1>, <1074 1>, + <1075 1>, <1076 1>, <1077 1>, <1078 1>, <1079 1>, + <1080 1>, <1081 1>, <1082 1>, <1083 1>, <1084 1>, + <1085 1>, <1086 1>, <1087 1>, <1088 1>, <1089 1>, + <1090 1>, <1091 1>, <1092 1>, <1093 1>, <1094 1>, + <1095 1>, <1096 1>, <1097 1>, <1098 1>, <1099 1>, + <1100 1>, <1101 1>, <1102 1>, <1103 1>, <1104 1>, + <1105 1>, <1106 1>, <1107 1>, <1108 1>, <1109 1>, + <1110 1>, <1111 1>, <1112 1>, <1113 1>, <1114 1>, + <1115 1>, <1116 1>, <1117 1>, <1118 1>, <1119 1>, + <1120 1>, <1121 1>, <1122 1>, <1123 1>, <1124 1>, + <1125 1>, <1126 1>, <1127 1>, <1128 1>, <1129 1>, + <1130 1>, <1131 1>, <1132 1>, <1133 1>, <1134 1>, + <1135 1>, <1136 1>, <1137 1>, <1138 1>, <1139 1>, + <1140 1>, <1141 1>, <1142 1>, <1143 1>, <1144 1>, + <1145 1>, <1146 1>, <1147 1>, <1148 1>, <1149 1>, + <1150 1>, <1151 1>, <1152 1>, <1153 1>, <1154 1>, + <1155 1>, <1156 1>, <1157 1>, <1158 1>, <1159 1>, + <1160 1>, <1161 1>, <1162 1>, <1163 1>, <1164 1>, + <1165 1>, <1166 1>, <1167 1>, <1168 1>, <1169 1>, + <1170 1>, <1171 1>, <1172 1>, <1173 1>, <1174 1>, + <1175 1>, <1176 1>, <1177 1>, <1178 1>, <1179 1>, + <1180 1>, <1181 1>, <1182 1>, <1183 1>, <1184 1>, + <1185 1>, <1186 1>, <1187 1>, <1188 1>, <1189 1>, + <1190 1>, <1191 1>, <1192 1>, <1193 1>, <1194 1>, + <1195 1>, <1196 1>, <1197 1>, <1198 1>, <1199 1>, + <1200 1>, <1201 1>, <1202 1>, <1203 1>, <1204 1>, + <1205 1>, <1206 1>, <1207 1>, <1208 1>, <1209 1>, + <1210 1>, <1211 1>, <1212 1>, <1213 1>, <1214 1>, + <1215 1>, <1216 1>, <1217 1>, <1218 1>, <1219 1>, + <1220 1>, <1221 1>, <1222 1>, <1223 1>, <1224 1>, + <1225 1>, <1226 1>, <1227 1>, <1228 1>, <1229 1>, + <1230 1>, <1231 1>, <1232 1>, <1233 1>, <1234 1>, + <1235 1>, <1236 1>, <1237 1>, <1238 1>, <1239 1>, + <1240 1>, <1241 1>, <1242 1>, <1243 1>, <1244 1>, + <1245 1>, <1246 1>, <1247 1>, <1248 1>, <1249 1>, + <1250 1>, <1251 1>, <1252 1>, <1253 1>, <1254 1>, + <1255 1>, <1256 1>, <1257 1>, <1258 1>, <1259 1>, + <1260 1>, <1261 1>, <1262 1>, <1263 1>, <1264 1>, + <1265 1>, <1266 1>, <1267 1>, <1268 1>, <1269 1>, + <1270 1>, <1271 1>, <1272 1>, <1273 1>, <1274 1>, + <1275 1>, <1276 1>, <1277 1>, <1278 1>, <1279 1>, + <1280 1>, <1281 1>, <1282 1>, <1283 1>, <1284 1>, + <1285 1>, <1286 1>, <1287 1>, <1288 1>, <1289 1>, + <1290 1>, <1291 1>, <1292 1>, <1293 1>, <1294 1>, + <1295 1>, <1296 1>, <1297 1>, <1298 1>, <1299 1>, + <1300 1>, <1301 1>, <1302 1>, <1303 1>, <1304 1>, + <1305 1>, <1306 1>, <1307 1>, <1308 1>, <1309 1>, + <1310 1>, <1311 1>, <1312 1>, <1313 1>, <1314 1>, + <1315 1>, <1316 1>, <1317 1>, <1318 1>, <1319 1>, + <1320 1>, <1321 1>, <1322 1>, <1323 1>, <1324 1>, + <1325 1>, <1326 1>, <1327 1>, <1328 1>, <1329 1>, + <1330 1>, <1331 1>, <1332 1>, <1333 1>, <1334 1>, + <1335 1>, <1336 1>, <1337 1>, <1338 1>, <1339 1>, + <1340 1>, <1341 1>, <1342 1>, <1343 1>; + + desc-num = <0x400>; + buf-size = <0x1000>; + dma-coherent; + + port@0 { + reg = <0>; + serdes-syscon = <&serdes_ctrl>; + port-rst-offset = <0>; + port-mode-offset = <0>; + media-type = "fiber"; + }; + + port@1 { + reg = <1>; + serdes-syscon= <&serdes_ctrl>; + port-rst-offset = <1>; + port-mode-offset = <1>; + media-type = "fiber"; + }; + + port@4 { + reg = <4>; + phy-handle = <&phy0>; + serdes-syscon= <&serdes_ctrl>; + port-rst-offset = <4>; + port-mode-offset = <2>; + media-type = "copper"; + }; + + port@5 { + reg = <5>; + phy-handle = <&phy1>; + serdes-syscon= <&serdes_ctrl>; + port-rst-offset = <5>; + port-mode-offset = <3>; + media-type = "copper"; + }; + }; + + eth0: ethernet@4{ + compatible = "hisilicon,hns-nic-v2"; + ae-handle = <&dsaf0>; + port-idx-in-ae = <4>; + local-mac-address = [00 00 00 00 00 00]; + status = "disabled"; + dma-coherent; + }; + + eth1: ethernet@5{ + compatible = "hisilicon,hns-nic-v2"; + ae-handle = <&dsaf0>; + port-idx-in-ae = <5>; + local-mac-address = [00 00 00 00 00 00]; + status = "disabled"; + dma-coherent; + }; + + eth2: ethernet@0{ + compatible = "hisilicon,hns-nic-v2"; + ae-handle = <&dsaf0>; + port-idx-in-ae = <0>; + local-mac-address = [00 00 00 00 00 00]; + status = "disabled"; + dma-coherent; + }; + + eth3: ethernet@1{ + compatible = "hisilicon,hns-nic-v2"; + ae-handle = <&dsaf0>; + port-idx-in-ae = <1>; + local-mac-address = [00 00 00 00 00 00]; + status = "disabled"; + dma-coherent; + }; + + sas0: sas@c3000000 { + compatible = "hisilicon,hip06-sas-v2"; + reg = <0 0xc3000000 0 0x10000>; + sas-addr = [50 01 88 20 16 00 00 00]; + hisilicon,sas-syscon = <&dsa_subctrl>; + ctrl-reset-reg = <0xa60>; + ctrl-reset-sts-reg = <0x5a30>; + ctrl-clock-ena-reg = <0x338>; + queue-count = <16>; + phy-count = <8>; + dma-coherent; + interrupt-parent = <&mbigen_sas0>; + interrupts = <64 4>,<65 4>,<66 4>,<67 4>,<68 4>, + <69 4>,<70 4>,<71 4>,<72 4>,<73 4>, + <75 4>,<76 4>,<77 4>,<78 4>,<79 4>, + <80 4>,<81 4>,<82 4>,<83 4>,<84 4>, + <85 4>,<86 4>,<87 4>,<88 4>,<89 4>, + <90 4>,<91 4>,<92 4>,<93 4>,<94 4>, + <95 4>,<96 4>,<97 4>,<98 4>,<99 4>, + <100 4>,<101 4>,<102 4>,<103 4>,<104 4>, + <105 4>,<106 4>,<107 4>,<108 4>,<109 4>, + <110 4>,<111 4>,<112 4>,<113 4>,<114 4>, + <115 4>,<116 4>,<117 4>,<118 4>,<119 4>, + <120 4>,<121 4>,<122 4>,<123 4>,<124 4>, + <125 4>,<126 4>,<127 4>,<128 4>,<129 4>, + <130 4>,<131 4>,<132 4>,<133 4>,<134 4>, + <135 4>,<136 4>,<137 4>,<138 4>,<139 4>, + <140 4>,<141 4>,<142 4>,<143 4>,<144 4>, + <145 4>,<146 4>,<147 4>,<148 4>,<149 4>, + <150 4>,<151 4>,<152 4>,<153 4>,<154 4>, + <155 4>,<156 4>,<157 4>,<158 4>,<159 4>, + <160 4>,<601 1>,<602 1>,<603 1>,<604 1>, + <605 1>,<606 1>,<607 1>,<608 1>,<609 1>, + <610 1>,<611 1>,<612 1>,<613 1>,<614 1>, + <615 1>,<616 1>,<617 1>,<618 1>,<619 1>, + <620 1>,<621 1>,<622 1>,<623 1>,<624 1>, + <625 1>,<626 1>,<627 1>,<628 1>,<629 1>, + <630 1>,<631 1>,<632 1>; + status = "disabled"; + }; + + sas1: sas@a2000000 { + compatible = "hisilicon,hip06-sas-v2"; + reg = <0 0xa2000000 0 0x10000>; + sas-addr = [50 01 88 20 16 00 00 00]; + hisilicon,sas-syscon = <&pcie_subctl>; + am-max-trans; + ctrl-reset-reg = <0xa18>; + ctrl-reset-sts-reg = <0x5a0c>; + ctrl-clock-ena-reg = <0x318>; + queue-count = <16>; + phy-count = <8>; + dma-coherent; + interrupt-parent = <&mbigen_sas1>; + interrupts = <64 4>,<65 4>,<66 4>,<67 4>,<68 4>, + <69 4>,<70 4>,<71 4>,<72 4>,<73 4>, + <74 4>,<75 4>,<76 4>,<77 4>,<78 4>, + <79 4>,<80 4>,<81 4>,<82 4>,<83 4>, + <84 4>,<85 4>,<86 4>,<87 4>,<88 4>, + <89 4>,<90 4>,<91 4>,<92 4>,<93 4>, + <94 4>,<95 4>,<96 4>,<97 4>,<98 4>, + <99 4>,<100 4>,<101 4>,<102 4>,<103 4>, + <104 4>,<105 4>,<106 4>,<107 4>,<108 4>, + <109 4>,<110 4>,<111 4>,<112 4>,<113 4>, + <114 4>,<115 4>,<116 4>,<117 4>,<118 4>, + <119 4>,<120 4>,<121 4>,<122 4>,<123 4>, + <124 4>,<125 4>,<126 4>,<127 4>,<128 4>, + <129 4>,<130 4>,<131 4>,<132 4>,<133 4>, + <134 4>,<135 4>,<136 4>,<137 4>,<138 4>, + <139 4>,<140 4>,<141 4>,<142 4>,<143 4>, + <144 4>,<145 4>,<146 4>,<147 4>,<148 4>, + <149 4>,<150 4>,<151 4>,<152 4>,<153 4>, + <154 4>,<155 4>,<156 4>,<157 4>,<158 4>, + <159 4>,<576 1>,<577 1>,<578 1>,<579 1>, + <580 1>,<581 1>,<582 1>,<583 1>,<584 1>, + <585 1>,<586 1>,<587 1>,<588 1>,<589 1>, + <590 1>,<591 1>,<592 1>,<593 1>,<594 1>, + <595 1>,<596 1>,<597 1>,<598 1>,<599 1>, + <600 1>,<601 1>,<602 1>,<603 1>,<604 1>, + <605 1>,<606 1>,<607 1>; + status = "disabled"; + }; + + sas2: sas@a3000000 { + compatible = "hisilicon,hip06-sas-v2"; + reg = <0 0xa3000000 0 0x10000>; + sas-addr = [50 01 88 20 16 00 00 00]; + hisilicon,sas-syscon = <&pcie_subctl>; + ctrl-reset-reg = <0xae0>; + ctrl-reset-sts-reg = <0x5a70>; + ctrl-clock-ena-reg = <0x3a8>; + queue-count = <16>; + phy-count = <9>; + dma-coherent; + interrupt-parent = <&mbigen_sas2>; + interrupts = <192 4>,<193 4>,<194 4>,<195 4>,<196 4>, + <197 4>,<198 4>,<199 4>,<200 4>,<201 4>, + <202 4>,<203 4>,<204 4>,<205 4>,<206 4>, + <207 4>,<208 4>,<209 4>,<210 4>,<211 4>, + <212 4>,<213 4>,<214 4>,<215 4>,<216 4>, + <217 4>,<218 4>,<219 4>,<220 4>,<221 4>, + <222 4>,<223 4>,<224 4>,<225 4>,<226 4>, + <227 4>,<228 4>,<229 4>,<230 4>,<231 4>, + <232 4>,<233 4>,<234 4>,<235 4>,<236 4>, + <237 4>,<238 4>,<239 4>,<240 4>,<241 4>, + <242 4>,<243 4>,<244 4>,<245 4>,<246 4>, + <247 4>,<248 4>,<249 4>,<250 4>,<251 4>, + <252 4>,<253 4>,<254 4>,<255 4>,<256 4>, + <257 4>,<258 4>,<259 4>,<260 4>,<261 4>, + <262 4>,<263 4>,<264 4>,<265 4>,<266 4>, + <267 4>,<268 4>,<269 4>,<270 4>,<271 4>, + <272 4>,<273 4>,<274 4>,<275 4>,<276 4>, + <277 4>,<278 4>,<279 4>,<280 4>,<281 4>, + <282 4>,<283 4>,<284 4>,<285 4>,<286 4>, + <287 4>,<608 1>,<609 1>,<610 1>,<611 1>, + <612 1>,<613 1>,<614 1>,<615 1>,<616 1>, + <617 1>,<618 1>,<619 1>,<620 1>,<621 1>, + <622 1>,<623 1>,<624 1>,<625 1>,<626 1>, + <627 1>,<628 1>,<629 1>,<630 1>,<631 1>, + <632 1>,<633 1>,<634 1>,<635 1>,<636 1>, + <637 1>,<638 1>,<639 1>; + status = "disabled"; + }; }; }; diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile index 308468d377d0..cf3953124cef 100644 --- a/arch/arm64/boot/dts/marvell/Makefile +++ b/arch/arm64/boot/dts/marvell/Makefile @@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_BERLIN) += berlin4ct-stb.dtb # Mvebu SoC Family dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/marvell/armada-8020.dtsi b/arch/arm64/boot/dts/marvell/armada-8020.dtsi index 3753c1c6d54d..048e5cf5160e 100644 --- a/arch/arm64/boot/dts/marvell/armada-8020.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-8020.dtsi @@ -47,6 +47,7 @@ #include "armada-ap806-dual.dtsi" #include "armada-cp110-master.dtsi" +#include "armada-cp110-slave.dtsi" / { model = "Marvell Armada 8020"; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-db.dts b/arch/arm64/boot/dts/marvell/armada-8040-db.dts new file mode 100644 index 000000000000..6e6f182fb297 --- /dev/null +++ b/arch/arm64/boot/dts/marvell/armada-8040-db.dts @@ -0,0 +1,150 @@ +/* + * Copyright (C) 2016 Marvell Technology Group Ltd. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* + * Device Tree file for Marvell Armada 8040 Development board platform + */ + +#include "armada-8040.dtsi" + +/ { + model = "Marvell Armada 8040 DB board"; + compatible = "marvell,armada8040-db", "marvell,armada8040", + "marvell,armada-ap806-quad", "marvell,armada-ap806"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@00000000 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; +}; + +&spi0 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x200000>; + }; + partition@400000 { + label = "Filesystem"; + reg = <0x200000 0xce0000>; + }; + }; + }; +}; + +/* Accessible over the mini-USB CON9 connector on the main board */ +&uart0 { + status = "okay"; +}; + + +/* CON5 on CP0 expansion */ +&cpm_pcie2 { + status = "okay"; +}; + +&cpm_i2c0 { + status = "okay"; + clock-frequency = <100000>; +}; + +/* CON4 on CP0 expansion */ +&cpm_sata0 { + status = "okay"; +}; + +/* CON9 on CP0 expansion */ +&cpm_usb3_0 { + status = "okay"; +}; + +/* CON10 on CP0 expansion */ +&cpm_usb3_1 { + status = "okay"; +}; + +/* CON5 on CP1 expansion */ +&cps_pcie2 { + status = "okay"; +}; + +&cps_i2c0 { + status = "okay"; + clock-frequency = <100000>; +}; + +/* CON4 on CP1 expansion */ +&cps_sata0 { + status = "okay"; +}; + +/* CON9 on CP1 expansion */ +&cps_usb3_0 { + status = "okay"; +}; + +/* CON10 on CP1 expansion */ +&cps_usb3_1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/marvell/armada-8040.dtsi b/arch/arm64/boot/dts/marvell/armada-8040.dtsi index 8bd0d8f8ad4c..9c1b28c47683 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-8040.dtsi @@ -47,6 +47,7 @@ #include "armada-ap806-quad.dtsi" #include "armada-cp110-master.dtsi" +#include "armada-cp110-slave.dtsi" / { model = "Marvell Armada 8040"; diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi index c2a6745f168c..7b6136182ad0 100644 --- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi @@ -128,6 +128,12 @@ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; }; + pmu { + compatible = "arm,cortex-a72-pmu"; + interrupt-parent = <&pic>; + interrupts = <17>; + }; + odmi: odmi@300000 { compatible = "marvell,odmi-controller"; interrupt-controller; @@ -140,6 +146,14 @@ marvell,spi-base = <128>, <136>, <144>, <152>; }; + pic: interrupt-controller@3f0100 { + compatible = "marvell,armada-8k-pic"; + reg = <0x3f0100 0x10>; + #interrupt-cells = <1>; + interrupt-controller; + interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>; + }; + xor@400000 { compatible = "marvell,armada-7k-xor", "marvell,xor-v2"; reg = <0x400000 0x1000>, diff --git a/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi new file mode 100644 index 000000000000..6ff12016327e --- /dev/null +++ b/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi @@ -0,0 +1,246 @@ +/* + * Copyright (C) 2016 Marvell Technology Group Ltd. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* + * Device Tree file for Marvell Armada CP110 Slave. + */ + +/ { + cp110-slave { + #address-cells = <2>; + #size-cells = <2>; + compatible = "simple-bus"; + interrupt-parent = <&gic>; + ranges; + + config-space { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + interrupt-parent = <&gic>; + ranges = <0x0 0x0 0xf4000000 0x2000000>; + + cps_syscon0: system-controller@440000 { + compatible = "marvell,cp110-system-controller0", + "syscon"; + reg = <0x440000 0x1000>; + #clock-cells = <2>; + core-clock-output-names = + "cps-apll", "cps-ppv2-core", "cps-eip", + "cps-core", "cps-nand-core"; + gate-clock-output-names = + "cps-audio", "cps-communit", "cps-nand", + "cps-ppv2", "cps-sdio", "cps-mg-domain", + "cps-mg-core", "cps-xor1", "cps-xor0", + "cps-gop-dp", "none", "cps-pcie_x10", + "cps-pcie_x11", "cps-pcie_x4", "cps-pcie-xor", + "cps-sata", "cps-sata-usb", "cps-main", + "cps-sd-mmc", "none", "none", + "cps-slow-io", "cps-usb3h0", "cps-usb3h1", + "cps-usb3dev", "cps-eip150", "cps-eip197"; + }; + + cps_sata0: sata@540000 { + compatible = "marvell,armada-8k-ahci"; + reg = <0x540000 0x30000>; + interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cps_syscon0 1 15>; + status = "disabled"; + }; + + cps_usb3_0: usb3@500000 { + compatible = "marvell,armada-8k-xhci", + "generic-xhci"; + reg = <0x500000 0x4000>; + dma-coherent; + interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cps_syscon0 1 22>; + status = "disabled"; + }; + + cps_usb3_1: usb3@510000 { + compatible = "marvell,armada-8k-xhci", + "generic-xhci"; + reg = <0x510000 0x4000>; + dma-coherent; + interrupts = <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cps_syscon0 1 23>; + status = "disabled"; + }; + + cps_xor0: xor@6a0000 { + compatible = "marvell,armada-7k-xor", "marvell,xor-v2"; + reg = <0x6a0000 0x1000>, + <0x6b0000 0x1000>; + dma-coherent; + msi-parent = <&gic_v2m0>; + clocks = <&cps_syscon0 1 8>; + }; + + cps_xor1: xor@6c0000 { + compatible = "marvell,armada-7k-xor", "marvell,xor-v2"; + reg = <0x6c0000 0x1000>, + <0x6d0000 0x1000>; + dma-coherent; + msi-parent = <&gic_v2m0>; + clocks = <&cps_syscon0 1 7>; + }; + + cps_spi0: spi@700600 { + compatible = "marvell,armada-380-spi"; + reg = <0x700600 0x50>; + #address-cells = <0x1>; + #size-cells = <0x0>; + cell-index = <1>; + clocks = <&cps_syscon0 0 3>; + status = "disabled"; + }; + + cps_spi1: spi@700680 { + compatible = "marvell,armada-380-spi"; + reg = <0x700680 0x50>; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <2>; + clocks = <&cps_syscon0 1 21>; + status = "disabled"; + }; + + cps_i2c0: i2c@701000 { + compatible = "marvell,mv78230-i2c"; + reg = <0x701000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cps_syscon0 1 21>; + status = "disabled"; + }; + + cps_i2c1: i2c@701100 { + compatible = "marvell,mv78230-i2c"; + reg = <0x701100 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cps_syscon0 1 21>; + status = "disabled"; + }; + }; + + cps_pcie0: pcie@f4600000 { + compatible = "marvell,armada8k-pcie", "snps,dw-pcie"; + reg = <0 0xf4600000 0 0x10000>, + <0 0xfaf00000 0 0x80000>; + reg-names = "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + dma-coherent; + + bus-range = <0 0xff>; + ranges = + /* downstream I/O */ + <0x81000000 0 0xfd000000 0 0xfd000000 0 0x10000 + /* non-prefetchable memory */ + 0x82000000 0 0xfa000000 0 0xfa000000 0 0xf00000>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <1>; + clocks = <&cps_syscon0 1 13>; + status = "disabled"; + }; + + cps_pcie1: pcie@f4620000 { + compatible = "marvell,armada8k-pcie", "snps,dw-pcie"; + reg = <0 0xf4620000 0 0x10000>, + <0 0xfbf00000 0 0x80000>; + reg-names = "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + dma-coherent; + + bus-range = <0 0xff>; + ranges = + /* downstream I/O */ + <0x81000000 0 0xfd010000 0 0xfd010000 0 0x10000 + /* non-prefetchable memory */ + 0x82000000 0 0xfb000000 0 0xfb000000 0 0xf00000>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>; + + num-lanes = <1>; + clocks = <&cps_syscon0 1 11>; + status = "disabled"; + }; + + cps_pcie2: pcie@f4640000 { + compatible = "marvell,armada8k-pcie", "snps,dw-pcie"; + reg = <0 0xf4640000 0 0x10000>, + <0 0xfcf00000 0 0x80000>; + reg-names = "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + dma-coherent; + + bus-range = <0 0xff>; + ranges = + /* downstream I/O */ + <0x81000000 0 0xfd020000 0 0xfd020000 0 0x10000 + /* non-prefetchable memory */ + 0x82000000 0 0xfc000000 0 0xfc000000 0 0xf00000>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>; + + num-lanes = <1>; + clocks = <&cps_syscon0 1 12>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts index 7453a47b3047..2a7f731c7759 100644 --- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts +++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts @@ -42,6 +42,44 @@ gpio = <&pio 130 GPIO_ACTIVE_HIGH>; enable-active-high; }; + + connector { + compatible = "hdmi-connector"; + label = "hdmi"; + type = "d"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; + }; +}; + +&cec { + status = "okay"; +}; + +&dpi0 { + status = "okay"; +}; + +&hdmi_phy { + status = "okay"; +}; + +&hdmi0 { + status = "okay"; + + ports { + port@1 { + reg = <1>; + + hdmi0_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; }; &i2c1 { diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi index 10f638f4e7d8..1c71e256601d 100644 --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi @@ -254,6 +254,16 @@ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + hdmi_pin: xxx { + + /*hdmi htplg pin*/ + pins1 { + pinmux = <MT8173_PIN_21_HTPLG__FUNC_HTPLG>; + input-enable; + bias-pull-down; + }; + }; + i2c0_pins_a: i2c0 { pins1 { pinmux = <MT8173_PIN_45_SDA0__FUNC_SDA0>, @@ -341,6 +351,14 @@ clock-names = "spi", "wrap"; }; + cec: cec@10013000 { + compatible = "mediatek,mt8173-cec"; + reg = <0 0x10013000 0 0xbc>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_CEC>; + status = "disabled"; + }; + vpu: vpu@10020000 { compatible = "mediatek,mt8173-vpu"; reg = <0 0x10020000 0 0x30000>, @@ -383,6 +401,19 @@ #clock-cells = <1>; }; + hdmi_phy: hdmi-phy@10209100 { + compatible = "mediatek,mt8173-hdmi-phy"; + reg = <0 0x10209100 0 0x24>; + clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>; + clock-names = "pll_ref"; + clock-output-names = "hdmitx_dig_cts"; + mediatek,ibias = <0xa>; + mediatek,ibias_up = <0x1c>; + #clock-cells = <0>; + #phy-cells = <0>; + status = "disabled"; + }; + mipi_tx0: mipi-dphy@10215000 { compatible = "mediatek,mt8173-mipi-tx"; reg = <0 0x10215000 0 0x1000>; @@ -577,6 +608,14 @@ status = "disabled"; }; + hdmiddc0: i2c@11012000 { + compatible = "mediatek,mt8173-hdmi-ddc"; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>; + reg = <0 0x11012000 0 0x1C>; + clocks = <&pericfg CLK_PERI_I2C5>; + clock-names = "ddc-i2c"; + }; + i2c6: i2c@11013000 { compatible = "mediatek,mt8173-i2c"; reg = <0 0x11013000 0 0x70>, @@ -885,6 +924,12 @@ <&apmixedsys CLK_APMIXED_TVDPLL>; clock-names = "pixel", "engine", "pll"; status = "disabled"; + + port { + dpi0_out: endpoint { + remote-endpoint = <&hdmi0_in>; + }; + }; }; pwm0: pwm@1401e000 { @@ -942,6 +987,38 @@ clocks = <&mmsys CLK_MM_DISP_OD>; }; + hdmi0: hdmi@14025000 { + compatible = "mediatek,mt8173-hdmi"; + reg = <0 0x14025000 0 0x400>; + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_HDMI_PIXEL>, + <&mmsys CLK_MM_HDMI_PLLCK>, + <&mmsys CLK_MM_HDMI_AUDIO>, + <&mmsys CLK_MM_HDMI_SPDIF>; + clock-names = "pixel", "pll", "bclk", "spdif"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pin>; + phys = <&hdmi_phy>; + phy-names = "hdmi"; + mediatek,syscon-hdmi = <&mmsys 0x900>; + assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>; + assigned-clock-parents = <&hdmi_phy>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi0_in: endpoint { + remote-endpoint = <&dpi0_out>; + }; + }; + }; + }; + larb4: larb@14027000 { compatible = "mediatek,mt8173-smi-larb"; reg = <0 0x14027000 0 0x1000>; diff --git a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts index 431266a48e9c..c2becb603e11 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts +++ b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts @@ -27,6 +27,12 @@ reg = <0x0 0x80000000 0x0 0xc0000000>; }; + host1x@50000000 { + dpaux: dpaux@545c0000 { + status = "okay"; + }; + }; + pinmux: pinmux@700008d4 { pinctrl-names = "boot"; pinctrl-0 = <&state_boot>; @@ -1556,6 +1562,46 @@ }; }; + i2c@7000d100 { + status = "okay"; + clock-frequency = <400000>; + + nau8825@1a { + compatible = "nuvoton,nau8825"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>; + clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>; + clock-names = "mclk"; + + nuvoton,jkdet-enable; + nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>; + nuvoton,vref-impedance = <2>; + nuvoton,micbias-voltage = <6>; + nuvoton,sar-threshold-num = <4>; + nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>; + nuvoton,sar-hysteresis = <1>; + nuvoton,sar-voltage = <0>; + nuvoton,sar-compare-time = <0>; + nuvoton,sar-sampling-time = <0>; + nuvoton,short-key-debounce = <2>; + nuvoton,jack-insert-debounce = <7>; + nuvoton,jack-eject-debounce = <7>; + status = "okay"; + }; + + audio-codec@2d { + compatible = "realtek,rt5677"; + reg = <0x2d>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(X, 0) IRQ_TYPE_LEVEL_HIGH>; + realtek,reset-gpio = <&gpio TEGRA_GPIO(BB, 3) GPIO_ACTIVE_LOW>; + gpio-controller; + #gpio-cells = <2>; + status = "okay"; + }; + }; + pmc@7000e400 { nvidia,invert-interrupt; nvidia,suspend-mode = <0>; @@ -1568,12 +1614,81 @@ status = "okay"; }; + usb@70090000 { + phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-6}>; + phy-names = "usb2-0", "usb3-0"; + + dvddio-pex-supply = <&avddio_1v05>; + hvddio-pex-supply = <&pp1800>; + avdd-usb-supply = <&pp3300>; + avdd-pll-utmip-supply = <&pp1800>; + avdd-pll-uerefe-supply = <&pp1050_avdd>; + dvdd-pex-pll-supply = <&avddio_1v05>; + hvdd-pex-pll-e-supply = <&pp1800>; + + status = "okay"; + }; + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-6 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "okay"; + vbus-supply = <&usbc_vbus>; + mode = "otg"; + }; + + usb3-0 { + nvidia,usb2-companion = <0>; + status = "okay"; + }; + }; + }; + sdhci@700b0600 { bus-width = <8>; non-removable; status = "okay"; }; + aconnect@702c0000 { + status = "okay"; + + dma@702e2000 { + status = "okay"; + }; + + agic@702f9000 { + status = "okay"; + }; + }; + clocks { compatible = "simple-bus"; #address-cells = <1>; @@ -1646,6 +1761,11 @@ }; }; + max98357a { + compatible = "maxim,max98357a"; + status = "okay"; + }; + psci { compatible = "arm,psci-1.0"; method = "smc"; diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi index c4cfdcf60d26..f6739797150a 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi @@ -34,6 +34,7 @@ clock-names = "dpaux", "parent"; resets = <&tegra_car 207>; reset-names = "dpaux"; + power-domains = <&pd_sor>; status = "disabled"; state_dpaux1_aux: pinmux-aux { @@ -108,6 +109,7 @@ clock-names = "dsi", "lp", "parent"; resets = <&tegra_car 48>; reset-names = "dsi"; + power-domains = <&pd_sor>; nvidia,mipi-calibrate = <&mipi 0x0c0>; /* DSIA & DSIB pads */ status = "disabled"; @@ -137,6 +139,7 @@ clock-names = "dsi", "lp", "parent"; resets = <&tegra_car 82>; reset-names = "dsi"; + power-domains = <&pd_sor>; nvidia,mipi-calibrate = <&mipi 0x300>; /* DSIC & DSID pads */ status = "disabled"; @@ -178,6 +181,7 @@ pinctrl-1 = <&state_dpaux_i2c>; pinctrl-2 = <&state_dpaux_off>; pinctrl-names = "aux", "i2c", "off"; + power-domains = <&pd_sor>; status = "disabled"; }; @@ -197,6 +201,7 @@ pinctrl-1 = <&state_dpaux1_i2c>; pinctrl-2 = <&state_dpaux1_off>; pinctrl-names = "aux", "i2c", "off"; + power-domains = <&pd_sor>; status = "disabled"; }; @@ -209,6 +214,7 @@ clock-names = "dpaux", "parent"; resets = <&tegra_car 181>; reset-names = "dpaux"; + power-domains = <&pd_sor>; status = "disabled"; state_dpaux_aux: pinmux-aux { @@ -325,7 +331,7 @@ }; gpio: gpio@6000d000 { - compatible = "nvidia,tegra210-gpio", "nvidia,tegra124-gpio", "nvidia,tegra30-gpio"; + compatible = "nvidia,tegra210-gpio", "nvidia,tegra30-gpio"; reg = <0x0 0x6000d000 0x0 0x1000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, @@ -648,27 +654,41 @@ #power-domain-cells = <0>; }; + pd_sor: sor { + clocks = <&tegra_car TEGRA210_CLK_SOR0>, + <&tegra_car TEGRA210_CLK_SOR1>, + <&tegra_car TEGRA210_CLK_CSI>, + <&tegra_car TEGRA210_CLK_DSIA>, + <&tegra_car TEGRA210_CLK_DSIB>, + <&tegra_car TEGRA210_CLK_DPAUX>, + <&tegra_car TEGRA210_CLK_DPAUX1>, + <&tegra_car TEGRA210_CLK_MIPI_CAL>; + resets = <&tegra_car TEGRA210_CLK_SOR0>, + <&tegra_car TEGRA210_CLK_SOR1>, + <&tegra_car TEGRA210_CLK_CSI>, + <&tegra_car TEGRA210_CLK_DSIA>, + <&tegra_car TEGRA210_CLK_DSIB>, + <&tegra_car TEGRA210_CLK_DPAUX>, + <&tegra_car TEGRA210_CLK_DPAUX1>, + <&tegra_car TEGRA210_CLK_MIPI_CAL>; + #power-domain-cells = <0>; + }; + pd_xusbss: xusba { clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>; - clock-names = "xusb-ss"; resets = <&tegra_car TEGRA210_CLK_XUSB_SS>; - reset-names = "xusb-ss"; #power-domain-cells = <0>; }; pd_xusbdev: xusbb { clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>; - clock-names = "xusb-dev"; resets = <&tegra_car 95>; - reset-names = "xusb-dev"; #power-domain-cells = <0>; }; pd_xusbhost: xusbc { clocks = <&tegra_car TEGRA210_CLK_XUSB_HOST>; - clock-names = "xusb-host"; resets = <&tegra_car TEGRA210_CLK_XUSB_HOST>; - reset-names = "xusb-host"; #power-domain-cells = <0>; }; }; @@ -948,6 +968,7 @@ reg = <0x0 0x700e3000 0x0 0x100>; clocks = <&tegra_car TEGRA210_CLK_MIPI_CAL>; clock-names = "mipi-cal"; + power-domains = <&pd_sor>; #nvidia,mipi-calibrate-cells = <1>; }; @@ -961,6 +982,50 @@ #size-cells = <1>; ranges = <0x702c0000 0x0 0x702c0000 0x00040000>; status = "disabled"; + + adma: dma@702e2000 { + compatible = "nvidia,tegra210-adma"; + reg = <0x702e2000 0x2000>; + interrupt-parent = <&agic>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + clocks = <&tegra_car TEGRA210_CLK_D_AUDIO>; + clock-names = "d_audio"; + status = "disabled"; + }; + + agic: agic@702f9000 { + compatible = "nvidia,tegra210-agic"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x702f9000 0x2000>, + <0x702fa000 0x2000>; + interrupts = <GIC_SPI 102 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + clocks = <&tegra_car TEGRA210_CLK_APE>; + clock-names = "clk"; + status = "disabled"; + }; }; spi@70410000 { diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index fa1f661ccccf..5dd05de5619b 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -1,5 +1,6 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb always := $(dtb-y) subdir-y := $(dts-dirs) diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi index ee828a8a8236..e1e6c6b5c489 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi @@ -24,4 +24,52 @@ bias-pull-up; }; }; + + adv7533_int_active: adv533_int_active { + pinmux { + function = "gpio"; + pins = "gpio31"; + }; + pinconf { + pins = "gpio31"; + drive-strength = <16>; + bias-disable; + }; + }; + + adv7533_int_suspend: adv7533_int_suspend { + pinmux { + function = "gpio"; + pins = "gpio31"; + }; + pinconf { + pins = "gpio31"; + drive-strength = <2>; + bias-disable; + }; + }; + + adv7533_switch_active: adv7533_switch_active { + pinmux { + function = "gpio"; + pins = "gpio32"; + }; + pinconf { + pins = "gpio32"; + drive-strength = <16>; + bias-disable; + }; + }; + + adv7533_switch_suspend: adv7533_switch_suspend { + pinmux { + function = "gpio"; + pins = "gpio32"; + }; + pinconf { + pins = "gpio32"; + drive-strength = <2>; + bias-disable; + }; + }; }; diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index 18639bc0a506..bb062b547110 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -63,6 +63,47 @@ /* On High speed expansion */ label = "HS-I2C2"; status = "okay"; + + adv_bridge: bridge@39 { + status = "okay"; + + compatible = "adi,adv7533"; + reg = <0x39>; + + interrupt-parent = <&msmgpio>; + interrupts = <31 2>; + + adi,dsi-lanes = <4>; + + pd-gpios = <&msmgpio 32 0>; + + avdd-supply = <&pm8916_l6>; + v1p2-supply = <&pm8916_l6>; + v3p3-supply = <&pm8916_l17>; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>; + pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7533_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + adv7533_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; }; i2c@78ba000 { @@ -180,6 +221,36 @@ lpass@07708000 { status = "okay"; }; + + mdss@1a00000 { + status = "okay"; + + mdp@1a01000 { + status = "okay"; + }; + + dsi@1a98000 { + status = "okay"; + + vdda-supply = <&pm8916_l2>; + vddio-supply = <&pm8916_l6>; + + ports { + port@1 { + endpoint { + remote-endpoint = <&adv7533_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + }; + + dsi-phy@1a98300 { + status = "okay"; + + vddio-supply = <&pm8916_l6>; + }; + }; }; usb2513 { @@ -194,6 +265,17 @@ pinctrl-names = "default"; pinctrl-0 = <&usb_id_default>; }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7533_out>; + }; + }; + }; }; &smd_rpm_regulators { diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi new file mode 100644 index 000000000000..24552f19b3fa --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi @@ -0,0 +1,39 @@ +/* + * Copyright (c) 2013-2016, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +&msmgpio { + sdc2_cd_on: sdc2_cd_on { + mux { + pins = "gpio38"; + function = "gpio"; + }; + + config { + pins = "gpio38"; + bias-pull-up; /* pull up */ + drive-strength = <16>; /* 16 MA */ + }; + }; + + sdc2_cd_off: sdc2_cd_off { + mux { + pins = "gpio38"; + function = "gpio"; + }; + + config { + pins = "gpio38"; + bias-pull-up; /* pull up */ + drive-strength = <2>; /* 2 MA */ + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts new file mode 100644 index 000000000000..230e9c8484ac --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts @@ -0,0 +1,21 @@ +/* + * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/dts-v1/; + +#include "apq8096-db820c.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. DB820c"; + compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc"; +}; diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi new file mode 100644 index 000000000000..afb218cffc60 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi @@ -0,0 +1,88 @@ +/* + * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include "msm8996.dtsi" +#include "apq8096-db820c-pins.dtsi" + +/ { + aliases { + serial0 = &blsp2_uart1; + serial1 = &blsp2_uart2; + i2c0 = &blsp1_i2c2; + i2c1 = &blsp2_i2c1; + i2c2 = &blsp2_i2c0; + spi0 = &blsp1_spi0; + spi1 = &blsp2_spi5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + soc { + serial@75b0000 { + label = "LS-UART1"; + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_uart1_2pins_default>; + pinctrl-1 = <&blsp2_uart1_2pins_sleep>; + }; + + serial@75b1000 { + label = "LS-UART0"; + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_uart2_4pins_default>; + pinctrl-1 = <&blsp2_uart2_4pins_sleep>; + }; + + i2c@07577000 { + /* On Low speed expansion */ + label = "LS-I2C0"; + status = "okay"; + }; + + i2c@075b6000 { + /* On Low speed expansion */ + label = "LS-I2C1"; + status = "okay"; + }; + + spi@07575000 { + /* On Low speed expansion */ + label = "LS-SPI0"; + status = "okay"; + }; + + i2c@075b5000 { + /* On High speed expansion */ + label = "HS-I2C2"; + status = "okay"; + }; + + spi@075ba000{ + /* On High speed expansion */ + label = "HS-SPI1"; + status = "okay"; + }; + + sdhci@74a4900 { + /* External SD card */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + cd-gpios = <&msmgpio 38 0x1>; + status = "okay"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index 11bdc24cfc74..466ca5705c99 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -86,6 +86,11 @@ reg = <0x0 0x89300000 0x0 0x600000>; no-map; }; + + mba_mem: mba@8ea00000 { + no-map; + reg = <0 0x8ea00000 0 0x100000>; + }; }; cpus { @@ -155,6 +160,49 @@ interrupts = <GIC_PPI 7 GIC_CPU_MASK_SIMPLE(4)>; }; + thermal-zones { + cpu-thermal0 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 4>; + + trips { + cpu_alert0: trip0 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit0: trip1 { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu-thermal1 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 3>; + + trips { + cpu_alert1: trip0 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu_crit1: trip1 { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + }; + timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, @@ -187,10 +235,11 @@ }; firmware { - scm { + scm: scm { compatible = "qcom,scm"; clocks = <&gcc GCC_CRYPTO_CLK>, <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>; clock-names = "core", "bus", "iface"; + #reset-cells = <1>; }; }; @@ -228,6 +277,11 @@ reg = <0x1905000 0x20000>; }; + tcsr: syscon@1937000 { + compatible = "qcom,tcsr-msm8916", "syscon"; + reg = <0x1937000 0x30000>; + }; + tcsr_mutex: hwlock { compatible = "qcom,tcsr-mutex"; syscon = <&tcsr_mutex_regs 0 0x1000>; @@ -483,7 +537,7 @@ compatible = "qcom,ci-hdrc"; reg = <0x78d9000 0x400>; dr_mode = "peripheral"; - interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; usb-phy = <&usb_otg>; status = "disabled"; }; @@ -491,7 +545,7 @@ usb_host: ehci@78d9000 { compatible = "qcom,ehci-host"; reg = <0x78d9000 0x400>; - interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; usb-phy = <&usb_otg>; status = "disabled"; }; @@ -499,8 +553,8 @@ usb_otg: phy@78d9000 { compatible = "qcom,usb-otg-snps"; reg = <0x78d9000 0x400>; - interrupts = <GIC_SPI 134 IRQ_TYPE_EDGE_BOTH>, - <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; qcom,vdd-levels = <500000 1000000 1320000>; qcom,phy-init-sequence = <0x44 0x6B 0x24 0x13>; @@ -594,7 +648,7 @@ <0x200a000 0x002100>; reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; interrupt-names = "periph_irq"; - interrupts = <GIC_SPI 190 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; qcom,ee = <0>; qcom,channel = <0>; #address-cells = <2>; @@ -609,6 +663,144 @@ clocks = <&gcc GCC_PRNG_AHB_CLK>; clock-names = "core"; }; + + qfprom: qfprom@5c000 { + compatible = "qcom,qfprom"; + reg = <0x5c000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + tsens_caldata: caldata@d0 { + reg = <0xd0 0x8>; + }; + tsens_calsel: calsel@ec { + reg = <0xec 0x4>; + }; + }; + + tsens: thermal-sensor@4a8000 { + compatible = "qcom,msm8916-tsens"; + reg = <0x4a8000 0x2000>; + nvmem-cells = <&tsens_caldata>, <&tsens_calsel>; + nvmem-cell-names = "calib", "calib_sel"; + #thermal-sensor-cells = <1>; + }; + + mdss: mdss@1a00000 { + compatible = "qcom,mdss"; + reg = <0x1a00000 0x1000>, + <0x1ac8000 0x3000>; + reg-names = "mdss_phys", "vbif_phys"; + + power-domains = <&gcc MDSS_GDSC>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "vsync_clk"; + + interrupts = <0 72 0>; + + interrupt-controller; + #interrupt-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mdp: mdp@1a01000 { + compatible = "qcom,mdp5"; + reg = <0x1a01000 0x90000>; + reg-names = "mdp_phys"; + + interrupt-parent = <&mdss>; + interrupts = <0 0>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_MDP_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "core_clk", + "vsync_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp5_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + }; + + dsi0: dsi@1a98000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0x1a98000 0x25c>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <4 0>; + + assigned-clocks = <&gcc BYTE0_CLK_SRC>, + <&gcc PCLK0_CLK_SRC>; + assigned-clock-parents = <&dsi_phy0 0>, + <&dsi_phy0 1>; + + clocks = <&gcc GCC_MDSS_MDP_CLK>, + <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_BYTE0_CLK>, + <&gcc GCC_MDSS_PCLK0_CLK>, + <&gcc GCC_MDSS_ESC0_CLK>; + clock-names = "mdp_core_clk", + "iface_clk", + "bus_clk", + "byte_clk", + "pixel_clk", + "core_clk"; + phys = <&dsi_phy0>; + phy-names = "dsi-phy"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp5_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + }; + }; + }; + }; + + dsi_phy0: dsi-phy@1a98300 { + compatible = "qcom,dsi-phy-28nm-lp"; + reg = <0x1a98300 0xd4>, + <0x1a98500 0x280>, + <0x1a98780 0x30>; + reg-names = "dsi_pll", + "dsi_phy", + "dsi_phy_regulator"; + + #clock-cells = <1>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>; + clock-names = "iface_clk"; + }; + }; }; smd { @@ -657,6 +849,88 @@ }; }; }; + + hexagon-smp2p { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + + interrupts = <0 27 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 14>; + + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + hexagon_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,smem-state-cells = <1>; + }; + + hexagon_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + wcnss-smp2p { + compatible = "qcom,smp2p"; + qcom,smem = <451>, <431>; + + interrupts = <0 143 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 18>; + + qcom,local-pid = <0>; + qcom,remote-pid = <4>; + + wcnss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,smem-state-cells = <1>; + }; + + wcnss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smsm { + compatible = "qcom,smsm"; + + #address-cells = <1>; + #size-cells = <0>; + + qcom,ipc-1 = <&apcs 0 13>; + qcom,ipc-6 = <&apcs 0 19>; + + apps_smsm: apps@0 { + reg = <0>; + + #qcom,smem-state-cells = <1>; + }; + + hexagon_smsm: hexagon@1 { + reg = <1>; + interrupts = <0 26 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + wcnss_smsm: wcnss@6 { + reg = <6>; + interrupts = <0 144 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; }; #include "msm8916-pins.dtsi" diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi index 55ec3e8326b7..338f82a7fdc7 100644 --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi @@ -97,6 +97,92 @@ }; }; + thermal-zones { + cpu-thermal0 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 3>; + + trips { + cpu_alert0: trip0 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_crit0: trip1 { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu-thermal1 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 5>; + + trips { + cpu_alert1: trip0 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_crit1: trip1 { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu-thermal2 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 8>; + + trips { + cpu_alert2: trip0 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_crit2: trip1 { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu-thermal3 { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 10>; + + trips { + cpu_alert3: trip0 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_crit3: trip1 { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, @@ -181,6 +267,12 @@ status = "disabled"; }; + tsens0: thermal-sensor@4a8000 { + compatible = "qcom,msm8996-tsens"; + reg = <0x4a8000 0x2000>; + #thermal-sensor-cells = <1>; + }; + blsp2_uart1: serial@75b0000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x75b0000 0x1000>; @@ -339,7 +431,7 @@ <0x400a000 0x002100>; reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; interrupt-names = "periph_irq"; - interrupts = <GIC_SPI 326 IRQ_TYPE_NONE>; + interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>; qcom,ee = <0>; qcom,channel = <0>; #address-cells = <2>; diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile index 7037a161b6ef..87669f656454 100644 --- a/arch/arm64/boot/dts/rockchip/Makefile +++ b/arch/arm64/boot/dts/rockchip/Makefile @@ -1,5 +1,6 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb diff --git a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts new file mode 100644 index 000000000000..5797933ef80e --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts @@ -0,0 +1,382 @@ +/* + * Copyright (c) 2016 Matthias Brugger <mbrugger@suse.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include "rk3368.dtsi" + +/ { + model = "Rockchip Orion R68"; + compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368"; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + memory { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + pinctrl-0 = <&emmc_reset>; + pinctrl-names = "default"; + reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>; + }; + + ext_gmac: external-gmac-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + clock-output-names = "ext_gmac"; + }; + + keys: gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pwr_key>; + + power { + wakeup-source; + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + label = "GPIO Power"; + linux,code = <KEY_POWER>; + }; + }; + + leds: gpio-leds { + compatible = "gpio-leds"; + + red { + gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>; + label = "orion:red:led"; + pinctrl-names = "default"; + pinctrl-0 = <&led_ctl>; + default-state = "on"; + }; + + blue { + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + label = "orion:blue:led"; + pinctrl-names = "default"; + pinctrl-0 = <&stby_pwren>; + default-state = "off"; + }; + }; + + vcc_18: vcc18-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + /* supplies both host and otg */ + vcc_host: vcc-host-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio0 4 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&host_vbus_drv>; + regulator-name = "vcc_host"; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + vcc_io: vcc-io-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + vcc_lan: vcc-lan-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_lan"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_io>; + }; + + vcc_sd: vcc-sd-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sd"; + gpio = <&gpio3 11 GPIO_ACTIVE_LOW>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_io>; + }; + + vcc_sys: vcc-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vccio_sd: vcc-io-sd-regulator { + compatible = "regulator-fixed"; + regulator-name= "vccio_sd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_io>; + }; + + vccio_wl: vccio-wl-regulator { + compatible = "regulator-fixed"; + regulator-name = "vccio_wl"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_io>; + }; + + vdd_10: vdd-10-regulator { + compatible = "regulator-fixed"; + regulator-name = "vdd_10"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; +}; + +&emmc { + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + keep-power-in-suspend; + mmc-pwrseq = <&emmc_pwrseq>; + mmc-hs200-1_2v; + mmc-hs200-1_8v; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>; + status = "okay"; +}; + +&gmac { + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + clock_in_out = "input"; + phy-supply = <&vcc_lan>; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + snps,reset-gpio = <&gpio3 12 0>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + tx_delay = <0x30>; + rx_delay = <0x10>; + status = "ok"; +}; + +&i2c0 { + status = "okay"; + + vdd_cpu: syr827@40 { + compatible = "silergy,syr827"; + reg = <0x40>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu"; + regulator-enable-ramp-delay = <300>; + regulator-min-microvolt = <712500>; + regulator-max-microvolt = <1500000>; + regulator-ramp-delay = <8000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + hym8563: hym8563@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xin32k"; + /* rtc_int is not connected */ + }; +}; + +&pinctrl { + pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma { + bias-disable; + drive-strength = <8>; + }; + + pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma { + bias-pull-up; + drive-strength = <8>; + }; + + emmc { + emmc_bus8: emmc-bus8 { + rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>, + <1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>, + <1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>, + <1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>, + <1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>, + <1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>, + <1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>, + <1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>; + }; + + emmc-clk { + rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>; + }; + + emmc-cmd { + rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>; + }; + + emmc_reset: emmc-reset { + rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + keys { + pwr_key: pwr-key { + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; + + leds { + stby_pwren: stby-pwren { + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + led_ctl: led-ctl { + rockchip,pins = <3 29 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + sdmmc { + sdmmc_clk: sdmmc-clk { + rockchip,pins = <2 9 RK_FUNC_1 &pcfg_pull_none_drv_8ma>; + }; + + sdmmc_cmd: sdmmc-cmd { + rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_up_drv_8ma>; + }; + + sdmmc_cd: sdmmc-cd { + rockchip,pins = <2 11 RK_FUNC_1 &pcfg_pull_up_drv_8ma>; + }; + + sdmmc_bus1: sdmmc-bus1 { + rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>; + }; + + sdmmc_bus4: sdmmc-bus4 { + rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>, + <2 6 RK_FUNC_1 &pcfg_pull_up_drv_8ma>, + <2 7 RK_FUNC_1 &pcfg_pull_up_drv_8ma>, + <2 8 RK_FUNC_1 &pcfg_pull_up_drv_8ma>; + }; + }; + + usb { + host_vbus_drv: host-vbus-drv { + rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&saradc { + vref-supply = <&vcc_18>; + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + clock-frequency = <50000000>; + clock-freq-min-max = <400000 50000000>; + cap-sd-highspeed; + card-detect-delay = <200>; + keep-power-in-suspend; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + vmmc-supply = <&vcc_sd>; + vqmmc-supply = <&vccio_sd>; + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_xfer>; + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_otg { + status = "okay"; +}; + +&wdt { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/rockchip/rk3368-r88.dts b/arch/arm64/boot/dts/rockchip/rk3368-r88.dts index 82a32e5591e2..eed1ef6669ff 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368-r88.dts +++ b/arch/arm64/boot/dts/rockchip/rk3368-r88.dts @@ -248,7 +248,6 @@ &sdio0 { assigned-clocks = <&cru SCLK_SDIO0>; assigned-clock-parents = <&cru PLL_CPLL>; - broken-cd; bus-width = <4>; cap-sd-highspeed; cap-sdio-irq; diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi index d02a900378e1..6a5eeea44b63 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi @@ -45,6 +45,7 @@ #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/soc/rockchip,boot-mode.h> #include <dt-bindings/thermal/thermal.h> / { @@ -639,6 +640,15 @@ compatible = "rockchip,rk3368-pmu-io-voltage-domain"; status = "disabled"; }; + + reboot-mode { + compatible = "syscon-reboot-mode"; + offset = <0x200>; + mode-normal = <BOOT_NORMAL>; + mode-recovery = <BOOT_RECOVERY>; + mode-bootloader = <BOOT_FASTBOOT>; + mode-loader = <BOOT_BL_DOWNLOAD>; + }; }; cru: clock-controller@ff760000 { diff --git a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts index d33aa06d46f5..8e82497925fe 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts +++ b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts @@ -49,6 +49,13 @@ compatible = "rockchip,rk3399-evb", "rockchip,rk3399", "google,rk3399evb-rev2"; + clkin_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "clkin_gmac"; + #clock-cells = <0>; + }; + vdd_center: vdd-center { compatible = "pwm-regulator"; pwms = <&pwm3 0 25000 0>; @@ -69,18 +76,61 @@ regulator-max-microvolt = <3300000>; }; + vcc5v0_sys: vcc5v0-sys { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + vcc5v0_host: vcc5v0-host-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 25 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vcc5v0_host_en>; + regulator-name = "vcc5v0_host"; + vin-supply = <&vcc5v0_sys>; + }; + vcc_phy: vcc-phy-regulator { compatible = "regulator-fixed"; regulator-name = "vcc_phy"; regulator-always-on; regulator-boot-on; }; + + vcc_phy: vcc-phy-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_phy"; + regulator-always-on; + regulator-boot-on; + }; + }; &emmc_phy { status = "okay"; }; +&gmac { + assigned-clocks = <&cru SCLK_RMII_SRC>; + assigned-clock-parents = <&clkin_gmac>; + clock_in_out = "input"; + phy-supply = <&vcc_phy>; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + snps,reset-gpio = <&gpio3 15 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 50000>; + tx_delay = <0x28>; + rx_delay = <0x11>; + status = "okay"; +}; + &pwm0 { status = "okay"; }; @@ -101,6 +151,36 @@ status = "okay"; }; +&pcie_phy { + status = "disabled"; +}; + +&pcie0 { + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; + num-lanes = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreqn>; + status = "disabled"; +}; + +&u2phy0 { + status = "okay"; +}; + +&u2phy0_host { + phy-supply = <&vcc5v0_host>; + status = "okay"; +}; + +&u2phy1 { + status = "okay"; +}; + +&u2phy1_host { + phy-supply = <&vcc5v0_host>; + status = "okay"; +}; + &uart2 { status = "okay"; }; @@ -133,4 +213,11 @@ <1 18 RK_FUNC_GPIO &pcfg_pull_down>; }; }; + + usb2 { + vcc5v0_host_en: vcc5v0-host-en { + rockchip,pins = + <4 25 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; }; diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi index a6dd623a8845..b65c193dc64e 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi @@ -45,6 +45,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/power/rk3399-power.h> #include <dt-bindings/thermal/thermal.h> / { @@ -152,6 +153,16 @@ }; }; + pmu_a53 { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW &ppi_cluster0>; + }; + + pmu_a72 { + compatible = "arm,cortex-a72-pmu"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW &ppi_cluster1>; + }; + psci { compatible = "arm,psci-1.0"; method = "smc"; @@ -159,10 +170,10 @@ timer { compatible = "arm,armv8-timer"; - interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, - <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, - <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, - <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>; }; xin24m: xin24m { @@ -181,8 +192,8 @@ dmac_bus: dma-controller@ff6d0000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x0 0xff6d0000 0x0 0x4000>; - interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH 0>; #dma-cells = <1>; clocks = <&cru ACLK_DMAC0_PERILP>; clock-names = "apb_pclk"; @@ -191,19 +202,39 @@ dmac_peri: dma-controller@ff6e0000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x0 0xff6e0000 0x0 0x4000>; - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH 0>; #dma-cells = <1>; clocks = <&cru ACLK_DMAC1_PERILP>; clock-names = "apb_pclk"; }; }; + gmac: ethernet@fe300000 { + compatible = "rockchip,rk3399-gmac"; + reg = <0x0 0xfe300000 0x0 0x10000>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "macirq"; + clocks = <&cru SCLK_MAC>, <&cru SCLK_MAC_RX>, + <&cru SCLK_MAC_TX>, <&cru SCLK_MACREF>, + <&cru SCLK_MACREF_OUT>, <&cru ACLK_GMAC>, + <&cru PCLK_GMAC>; + clock-names = "stmmaceth", "mac_clk_rx", + "mac_clk_tx", "clk_mac_ref", + "clk_mac_refout", "aclk_mac", + "pclk_mac"; + power-domains = <&power RK3399_PD_GMAC>; + resets = <&cru SRST_A_GMAC>; + reset-names = "stmmaceth"; + rockchip,grf = <&grf>; + status = "disabled"; + }; + sdio0: dwmmc@fe310000 { compatible = "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc"; reg = <0x0 0xfe310000 0x0 0x4000>; - interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH 0>; clock-freq-min-max = <400000 150000000>; clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>, <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>; @@ -216,7 +247,7 @@ compatible = "rockchip,rk3399-dw-mshc", "rockchip,rk3288-dw-mshc"; reg = <0x0 0xfe320000 0x0 0x4000>; - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH 0>; clock-freq-min-max = <400000 150000000>; clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>, <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>; @@ -228,7 +259,7 @@ sdhci: sdhci@fe330000 { compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1"; reg = <0x0 0xfe330000 0x0 0x10000>; - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH 0>; arasan,soc-ctl-syscon = <&grf>; assigned-clocks = <&cru SCLK_EMMC>; assigned-clock-rates = <200000000>; @@ -241,19 +272,60 @@ status = "disabled"; }; + pcie0: pcie@f8000000 { + compatible = "rockchip,rk3399-pcie"; + reg = <0x0 0xf8000000 0x0 0x2000000>, + <0x0 0xfd000000 0x0 0x1000000>; + reg-names = "axi-base", "apb-base"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + bus-range = <0x0 0x1>; + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, + <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>; + clock-names = "aclk", "aclk-perf", + "hclk", "pm"; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "legacy", "client"; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie0_intc 0>, + <0 0 0 2 &pcie0_intc 1>, + <0 0 0 3 &pcie0_intc 2>, + <0 0 0 4 &pcie0_intc 3>; + msi-map = <0x0 &its 0x0 0x1000>; + phys = <&pcie_phy>; + phy-names = "pcie-phy"; + ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000 + 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>; + resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe"; + status = "disabled"; + + pcie0_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + usb_host0_ehci: usb@fe380000 { compatible = "generic-ehci"; reg = <0x0 0xfe380000 0x0 0x20000>; - interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH 0>; clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; clock-names = "hclk_host0", "hclk_host0_arb"; + phys = <&u2phy0_host>; + phy-names = "usb"; status = "disabled"; }; usb_host0_ohci: usb@fe3a0000 { compatible = "generic-ohci"; reg = <0x0 0xfe3a0000 0x0 0x20000>; - interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH 0>; clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>; clock-names = "hclk_host0", "hclk_host0_arb"; status = "disabled"; @@ -262,16 +334,18 @@ usb_host1_ehci: usb@fe3c0000 { compatible = "generic-ehci"; reg = <0x0 0xfe3c0000 0x0 0x20000>; - interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH 0>; clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; clock-names = "hclk_host1", "hclk_host1_arb"; + phys = <&u2phy1_host>; + phy-names = "usb"; status = "disabled"; }; usb_host1_ohci: usb@fe3e0000 { compatible = "generic-ohci"; reg = <0x0 0xfe3e0000 0x0 0x20000>; - interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>; clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>; clock-names = "hclk_host1", "hclk_host1_arb"; status = "disabled"; @@ -279,7 +353,7 @@ gic: interrupt-controller@fee00000 { compatible = "arm,gic-v3"; - #interrupt-cells = <3>; + #interrupt-cells = <4>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -290,12 +364,34 @@ <0x0 0xfff00000 0 0x10000>, /* GICC */ <0x0 0xfff10000 0 0x10000>, /* GICH */ <0x0 0xfff20000 0 0x10000>; /* GICV */ - interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>; its: interrupt-controller@fee20000 { compatible = "arm,gic-v3-its"; msi-controller; reg = <0x0 0xfee20000 0x0 0x20000>; }; + + ppi-partitions { + ppi_cluster0: interrupt-partition-0 { + affinity = <&cpu_l0 &cpu_l1 &cpu_l2 &cpu_l3>; + }; + + ppi_cluster1: interrupt-partition-1 { + affinity = <&cpu_b0 &cpu_b1>; + }; + }; + }; + + saradc: saradc@ff100000 { + compatible = "rockchip,rk3399-saradc"; + reg = <0x0 0xff100000 0x0 0x100>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH 0>; + #io-channel-cells = <1>; + clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; + clock-names = "saradc", "apb_pclk"; + resets = <&cru SRST_P_SARADC>; + reset-names = "saradc-apb"; + status = "disabled"; }; i2c1: i2c@ff110000 { @@ -305,7 +401,7 @@ assigned-clock-rates = <200000000>; clocks = <&cru SCLK_I2C1>, <&cru PCLK_I2C1>; clock-names = "i2c", "pclk"; - interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&i2c1_xfer>; #address-cells = <1>; @@ -320,7 +416,7 @@ assigned-clock-rates = <200000000>; clocks = <&cru SCLK_I2C2>, <&cru PCLK_I2C2>; clock-names = "i2c", "pclk"; - interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&i2c2_xfer>; #address-cells = <1>; @@ -335,7 +431,7 @@ assigned-clock-rates = <200000000>; clocks = <&cru SCLK_I2C3>, <&cru PCLK_I2C3>; clock-names = "i2c", "pclk"; - interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&i2c3_xfer>; #address-cells = <1>; @@ -350,7 +446,7 @@ assigned-clock-rates = <200000000>; clocks = <&cru SCLK_I2C5>, <&cru PCLK_I2C5>; clock-names = "i2c", "pclk"; - interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&i2c5_xfer>; #address-cells = <1>; @@ -365,7 +461,7 @@ assigned-clock-rates = <200000000>; clocks = <&cru SCLK_I2C6>, <&cru PCLK_I2C6>; clock-names = "i2c", "pclk"; - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&i2c6_xfer>; #address-cells = <1>; @@ -380,7 +476,7 @@ assigned-clock-rates = <200000000>; clocks = <&cru SCLK_I2C7>, <&cru PCLK_I2C7>; clock-names = "i2c", "pclk"; - interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&i2c7_xfer>; #address-cells = <1>; @@ -393,7 +489,7 @@ reg = <0x0 0xff180000 0x0 0x100>; clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; clock-names = "baudclk", "apb_pclk"; - interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH 0>; reg-shift = <2>; reg-io-width = <4>; pinctrl-names = "default"; @@ -406,7 +502,7 @@ reg = <0x0 0xff190000 0x0 0x100>; clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; clock-names = "baudclk", "apb_pclk"; - interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH 0>; reg-shift = <2>; reg-io-width = <4>; pinctrl-names = "default"; @@ -419,7 +515,7 @@ reg = <0x0 0xff1a0000 0x0 0x100>; clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; clock-names = "baudclk", "apb_pclk"; - interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH 0>; reg-shift = <2>; reg-io-width = <4>; pinctrl-names = "default"; @@ -432,7 +528,7 @@ reg = <0x0 0xff1b0000 0x0 0x100>; clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>; clock-names = "baudclk", "apb_pclk"; - interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH 0>; reg-shift = <2>; reg-io-width = <4>; pinctrl-names = "default"; @@ -445,7 +541,7 @@ reg = <0x0 0xff1c0000 0x0 0x1000>; clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; clock-names = "spiclk", "apb_pclk"; - interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>; #address-cells = <1>; @@ -458,7 +554,7 @@ reg = <0x0 0xff1d0000 0x0 0x1000>; clocks = <&cru SCLK_SPI1>, <&cru PCLK_SPI1>; clock-names = "spiclk", "apb_pclk"; - interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>; #address-cells = <1>; @@ -471,7 +567,7 @@ reg = <0x0 0xff1e0000 0x0 0x1000>; clocks = <&cru SCLK_SPI2>, <&cru PCLK_SPI2>; clock-names = "spiclk", "apb_pclk"; - interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&spi2_clk &spi2_tx &spi2_rx &spi2_cs0>; #address-cells = <1>; @@ -484,7 +580,7 @@ reg = <0x0 0xff1f0000 0x0 0x1000>; clocks = <&cru SCLK_SPI4>, <&cru PCLK_SPI4>; clock-names = "spiclk", "apb_pclk"; - interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&spi4_clk &spi4_tx &spi4_rx &spi4_cs0>; #address-cells = <1>; @@ -497,7 +593,7 @@ reg = <0x0 0xff200000 0x0 0x1000>; clocks = <&cru SCLK_SPI5>, <&cru PCLK_SPI5>; clock-names = "spiclk", "apb_pclk"; - interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&spi5_clk &spi5_tx &spi5_rx &spi5_cs0>; #address-cells = <1>; @@ -577,7 +673,7 @@ tsadc: tsadc@ff260000 { compatible = "rockchip,rk3399-tsadc"; reg = <0x0 0xff260000 0x0 0x100>; - interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH 0>; assigned-clocks = <&cru SCLK_TSADC>; assigned-clock-rates = <750000>; clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; @@ -594,6 +690,203 @@ status = "disabled"; }; + qos_gmac: qos@ffa5c000 { + compatible = "syscon"; + reg = <0x0 0xffa5c000 0x0 0x20>; + }; + + qos_hdcp: qos@ffa90000 { + compatible = "syscon"; + reg = <0x0 0xffa90000 0x0 0x20>; + }; + + qos_iep: qos@ffa98000 { + compatible = "syscon"; + reg = <0x0 0xffa98000 0x0 0x20>; + }; + + qos_isp0_m0: qos@ffaa0000 { + compatible = "syscon"; + reg = <0x0 0xffaa0000 0x0 0x20>; + }; + + qos_isp0_m1: qos@ffaa0080 { + compatible = "syscon"; + reg = <0x0 0xffaa0080 0x0 0x20>; + }; + + qos_isp1_m0: qos@ffaa8000 { + compatible = "syscon"; + reg = <0x0 0xffaa8000 0x0 0x20>; + }; + + qos_isp1_m1: qos@ffaa8080 { + compatible = "syscon"; + reg = <0x0 0xffaa8080 0x0 0x20>; + }; + + qos_rga_r: qos@ffab0000 { + compatible = "syscon"; + reg = <0x0 0xffab0000 0x0 0x20>; + }; + + qos_rga_w: qos@ffab0080 { + compatible = "syscon"; + reg = <0x0 0xffab0080 0x0 0x20>; + }; + + qos_video_m0: qos@ffab8000 { + compatible = "syscon"; + reg = <0x0 0xffab8000 0x0 0x20>; + }; + + qos_video_m1_r: qos@ffac0000 { + compatible = "syscon"; + reg = <0x0 0xffac0000 0x0 0x20>; + }; + + qos_video_m1_w: qos@ffac0080 { + compatible = "syscon"; + reg = <0x0 0xffac0080 0x0 0x20>; + }; + + qos_vop_big_r: qos@ffac8000 { + compatible = "syscon"; + reg = <0x0 0xffac8000 0x0 0x20>; + }; + + qos_vop_big_w: qos@ffac8080 { + compatible = "syscon"; + reg = <0x0 0xffac8080 0x0 0x20>; + }; + + qos_vop_little: qos@ffad0000 { + compatible = "syscon"; + reg = <0x0 0xffad0000 0x0 0x20>; + }; + + qos_gpu: qos@ffae0000 { + compatible = "syscon"; + reg = <0x0 0xffae0000 0x0 0x20>; + }; + + pmu: power-management@ff310000 { + compatible = "rockchip,rk3399-pmu", "syscon", "simple-mfd"; + reg = <0x0 0xff310000 0x0 0x1000>; + + /* + * Note: RK3399 supports 6 voltage domains including VD_CORE_L, + * VD_CORE_B, VD_CENTER, VD_GPU, VD_LOGIC and VD_PMU. + * Some of the power domains are grouped together for every + * voltage domain. + * The detail contents as below. + */ + power: power-controller { + compatible = "rockchip,rk3399-power-controller"; + #power-domain-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + /* These power domains are grouped by VD_CENTER */ + pd_iep@RK3399_PD_IEP { + reg = <RK3399_PD_IEP>; + clocks = <&cru ACLK_IEP>, + <&cru HCLK_IEP>; + pm_qos = <&qos_iep>; + }; + pd_rga@RK3399_PD_RGA { + reg = <RK3399_PD_RGA>; + clocks = <&cru ACLK_RGA>, + <&cru HCLK_RGA>; + pm_qos = <&qos_rga_r>, + <&qos_rga_w>; + }; + pd_vcodec@RK3399_PD_VCODEC { + reg = <RK3399_PD_VCODEC>; + clocks = <&cru ACLK_VCODEC>, + <&cru HCLK_VCODEC>; + pm_qos = <&qos_video_m0>; + }; + pd_vdu@RK3399_PD_VDU { + reg = <RK3399_PD_VDU>; + clocks = <&cru ACLK_VDU>, + <&cru HCLK_VDU>; + pm_qos = <&qos_video_m1_r>, + <&qos_video_m1_w>; + }; + + /* These power domains are grouped by VD_GPU */ + pd_gpu@RK3399_PD_GPU { + reg = <RK3399_PD_GPU>; + clocks = <&cru ACLK_GPU>; + pm_qos = <&qos_gpu>; + }; + + /* These power domains are grouped by VD_LOGIC */ + pd_gmac@RK3399_PD_GMAC { + reg = <RK3399_PD_GMAC>; + clocks = <&cru ACLK_GMAC>; + pm_qos = <&qos_gmac>; + }; + pd_vio@RK3399_PD_VIO { + reg = <RK3399_PD_VIO>; + #address-cells = <1>; + #size-cells = <0>; + + pd_hdcp@RK3399_PD_HDCP { + reg = <RK3399_PD_HDCP>; + clocks = <&cru ACLK_HDCP>, + <&cru HCLK_HDCP>, + <&cru PCLK_HDCP>; + pm_qos = <&qos_hdcp>; + }; + pd_isp0@RK3399_PD_ISP0 { + reg = <RK3399_PD_ISP0>; + clocks = <&cru ACLK_ISP0>, + <&cru HCLK_ISP0>; + pm_qos = <&qos_isp0_m0>, + <&qos_isp0_m1>; + }; + pd_isp1@RK3399_PD_ISP1 { + reg = <RK3399_PD_ISP1>; + clocks = <&cru ACLK_ISP1>, + <&cru HCLK_ISP1>; + pm_qos = <&qos_isp1_m0>, + <&qos_isp1_m1>; + }; + pd_tcpc0@RK3399_PD_TCPC0 { + reg = <RK3399_PD_TCPD0>; + clocks = <&cru SCLK_UPHY0_TCPDCORE>, + <&cru SCLK_UPHY0_TCPDPHY_REF>; + }; + pd_tcpc1@RK3399_PD_TCPC1 { + reg = <RK3399_PD_TCPD1>; + clocks = <&cru SCLK_UPHY1_TCPDCORE>, + <&cru SCLK_UPHY1_TCPDPHY_REF>; + }; + pd_vo@RK3399_PD_VO { + reg = <RK3399_PD_VO>; + #address-cells = <1>; + #size-cells = <0>; + + pd_vopb@RK3399_PD_VOPB { + reg = <RK3399_PD_VOPB>; + clocks = <&cru ACLK_VOP0>, + <&cru HCLK_VOP0>; + pm_qos = <&qos_vop_big_r>, + <&qos_vop_big_w>; + }; + pd_vopl@RK3399_PD_VOPL { + reg = <RK3399_PD_VOPL>; + clocks = <&cru ACLK_VOP1>, + <&cru HCLK_VOP1>; + pm_qos = <&qos_vop_little>; + }; + }; + }; + }; + }; + pmugrf: syscon@ff320000 { compatible = "rockchip,rk3399-pmugrf", "syscon", "simple-mfd"; reg = <0x0 0xff320000 0x0 0x1000>; @@ -611,7 +904,7 @@ reg = <0x0 0xff350000 0x0 0x1000>; clocks = <&pmucru SCLK_SPI3_PMU>, <&pmucru PCLK_SPI3_PMU>; clock-names = "spiclk", "apb_pclk"; - interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&spi3_clk &spi3_tx &spi3_rx &spi3_cs0>; #address-cells = <1>; @@ -624,7 +917,7 @@ reg = <0x0 0xff370000 0x0 0x100>; clocks = <&pmucru SCLK_UART4_PMU>, <&pmucru PCLK_UART4_PMU>; clock-names = "baudclk", "apb_pclk"; - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH 0>; reg-shift = <2>; reg-io-width = <4>; pinctrl-names = "default"; @@ -639,7 +932,7 @@ assigned-clock-rates = <200000000>; clocks = <&pmucru SCLK_I2C0_PMU>, <&pmucru PCLK_I2C0_PMU>; clock-names = "i2c", "pclk"; - interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&i2c0_xfer>; #address-cells = <1>; @@ -654,7 +947,7 @@ assigned-clock-rates = <200000000>; clocks = <&pmucru SCLK_I2C4_PMU>, <&pmucru PCLK_I2C4_PMU>; clock-names = "i2c", "pclk"; - interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&i2c4_xfer>; #address-cells = <1>; @@ -669,7 +962,7 @@ assigned-clock-rates = <200000000>; clocks = <&pmucru SCLK_I2C8_PMU>, <&pmucru PCLK_I2C8_PMU>; clock-names = "i2c", "pclk"; - interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH 0>; pinctrl-names = "default"; pinctrl-0 = <&i2c8_xfer>; #address-cells = <1>; @@ -721,6 +1014,35 @@ status = "disabled"; }; + efuse0: efuse@ff690000 { + compatible = "rockchip,rk3399-efuse"; + reg = <0x0 0xff690000 0x0 0x80>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&cru PCLK_EFUSE1024NS>; + clock-names = "pclk_efuse"; + + /* Data cells */ + cpub_leakage: cpu-leakage@17 { + reg = <0x17 0x1>; + }; + gpu_leakage: gpu-leakage@18 { + reg = <0x18 0x1>; + }; + center_leakage: center-leakage@19 { + reg = <0x19 0x1>; + }; + cpul_leakage: cpu-leakage@1a { + reg = <0x1a 0x1>; + }; + logic_leakage: logic-leakage@1b { + reg = <0x1b 0x1>; + }; + wafer_info: wafer-info@1c { + reg = <0x1c 0x1>; + }; + }; + pmucru: pmu-clock-controller@ff750000 { compatible = "rockchip,rk3399-pmucru"; reg = <0x0 0xff750000 0x0 0x1000>; @@ -741,7 +1063,7 @@ <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>, <&cru PCLK_PERIHP>, <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>, - <&cru PCLK_PERILP0>, + <&cru PCLK_PERILP0>, <&cru ACLK_CCI>, <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>; assigned-clock-rates = <594000000>, <800000000>, @@ -749,7 +1071,7 @@ <150000000>, <75000000>, <37500000>, <100000000>, <100000000>, - <50000000>, + <50000000>, <600000000>, <100000000>, <50000000>; }; @@ -764,6 +1086,40 @@ status = "disabled"; }; + u2phy0: usb2-phy@e450 { + compatible = "rockchip,rk3399-usb2phy"; + reg = <0xe450 0x10>; + clocks = <&cru SCLK_USB2PHY0_REF>; + clock-names = "phyclk"; + #clock-cells = <0>; + clock-output-names = "clk_usbphy0_480m"; + status = "disabled"; + + u2phy0_host: host-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "linestate"; + status = "disabled"; + }; + }; + + u2phy1: usb2-phy@e460 { + compatible = "rockchip,rk3399-usb2phy"; + reg = <0xe460 0x10>; + clocks = <&cru SCLK_USB2PHY1_REF>; + clock-names = "phyclk"; + #clock-cells = <0>; + clock-output-names = "clk_usbphy1_480m"; + status = "disabled"; + + u2phy1_host: host-port { + #phy-cells = <0>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "linestate"; + status = "disabled"; + }; + }; + emmc_phy: phy@f780 { compatible = "rockchip,rk3399-emmc-phy"; reg = <0xf780 0x24>; @@ -772,19 +1128,85 @@ #phy-cells = <0>; status = "disabled"; }; + + pcie_phy: pcie-phy { + compatible = "rockchip,rk3399-pcie-phy"; + clocks = <&cru SCLK_PCIEPHY_REF>; + clock-names = "refclk"; + #phy-cells = <0>; + resets = <&cru SRST_PCIEPHY>; + reset-names = "phy"; + status = "disabled"; + }; }; - watchdog@ff840000 { + tcphy0: phy@ff7c0000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff7c0000 0x0 0x40000>; + clocks = <&cru SCLK_UPHY0_TCPDCORE>, + <&cru SCLK_UPHY0_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY0>, + <&cru SRST_UPHY0_PIPE_L00>, + <&cru SRST_P_UPHY0_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + rockchip,grf = <&grf>; + rockchip,typec-conn-dir = <0xe580 0 16>; + rockchip,usb3tousb2-en = <0xe580 3 19>; + rockchip,external-psm = <0xe588 14 30>; + rockchip,pipe-status = <0xe5c0 0 0>; + status = "disabled"; + + tcphy0_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy0_usb3: usb3-port { + #phy-cells = <0>; + }; + }; + + tcphy1: phy@ff800000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff800000 0x0 0x40000>; + clocks = <&cru SCLK_UPHY1_TCPDCORE>, + <&cru SCLK_UPHY1_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY1>, + <&cru SRST_UPHY1_PIPE_L00>, + <&cru SRST_P_UPHY1_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + rockchip,grf = <&grf>; + rockchip,typec-conn-dir = <0xe58c 0 16>; + rockchip,usb3tousb2-en = <0xe58c 3 19>; + rockchip,external-psm = <0xe594 14 30>; + rockchip,pipe-status = <0xe5c0 16 16>; + status = "disabled"; + + tcphy1_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy1_usb3: usb3-port { + #phy-cells = <0>; + }; + }; + + watchdog@ff848000 { compatible = "snps,dw-wdt"; - reg = <0x0 0xff840000 0x0 0x100>; + reg = <0x0 0xff848000 0x0 0x100>; clocks = <&cru PCLK_WDT>; - interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH 0>; }; rktimer: rktimer@ff850000 { compatible = "rockchip,rk3399-timer"; reg = <0x0 0xff850000 0x0 0x1000>; - interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH 0>; clocks = <&cru PCLK_TIMER0>, <&cru SCLK_TIMER00>; clock-names = "pclk", "timer"; }; @@ -792,7 +1214,7 @@ spdif: spdif@ff870000 { compatible = "rockchip,rk3399-spdif"; reg = <0x0 0xff870000 0x0 0x1000>; - interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH 0>; dmas = <&dmac_bus 7>; dma-names = "tx"; clock-names = "mclk", "hclk"; @@ -806,7 +1228,7 @@ compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s"; reg = <0x0 0xff880000 0x0 0x1000>; rockchip,grf = <&grf>; - interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH 0>; dmas = <&dmac_bus 0>, <&dmac_bus 1>; dma-names = "tx", "rx"; clock-names = "i2s_clk", "i2s_hclk"; @@ -819,7 +1241,7 @@ i2s1: i2s@ff890000 { compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s"; reg = <0x0 0xff890000 0x0 0x1000>; - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH 0>; dmas = <&dmac_bus 2>, <&dmac_bus 3>; dma-names = "tx", "rx"; clock-names = "i2s_clk", "i2s_hclk"; @@ -832,7 +1254,7 @@ i2s2: i2s@ff8a0000 { compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s"; reg = <0x0 0xff8a0000 0x0 0x1000>; - interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH 0>; dmas = <&dmac_bus 4>, <&dmac_bus 5>; dma-names = "tx", "rx"; clock-names = "i2s_clk", "i2s_hclk"; @@ -852,7 +1274,7 @@ compatible = "rockchip,gpio-bank"; reg = <0x0 0xff720000 0x0 0x100>; clocks = <&pmucru PCLK_GPIO0_PMU>; - interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH 0>; gpio-controller; #gpio-cells = <0x2>; @@ -865,7 +1287,7 @@ compatible = "rockchip,gpio-bank"; reg = <0x0 0xff730000 0x0 0x100>; clocks = <&pmucru PCLK_GPIO1_PMU>; - interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH 0>; gpio-controller; #gpio-cells = <0x2>; @@ -878,7 +1300,7 @@ compatible = "rockchip,gpio-bank"; reg = <0x0 0xff780000 0x0 0x100>; clocks = <&cru PCLK_GPIO2>; - interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH 0>; gpio-controller; #gpio-cells = <0x2>; @@ -891,7 +1313,7 @@ compatible = "rockchip,gpio-bank"; reg = <0x0 0xff788000 0x0 0x100>; clocks = <&cru PCLK_GPIO3>; - interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH 0>; gpio-controller; #gpio-cells = <0x2>; @@ -904,7 +1326,7 @@ compatible = "rockchip,gpio-bank"; reg = <0x0 0xff790000 0x0 0x100>; clocks = <&cru PCLK_GPIO4>; - interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>; gpio-controller; #gpio-cells = <0x2>; @@ -955,6 +1377,72 @@ drive-strength = <13>; }; + clock { + clk_32k: clk-32k { + rockchip,pins = <0 0 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + gmac { + rgmii_pins: rgmii-pins { + rockchip,pins = + /* mac_txclk */ + <3 17 RK_FUNC_1 &pcfg_pull_none_13ma>, + /* mac_rxclk */ + <3 14 RK_FUNC_1 &pcfg_pull_none>, + /* mac_mdio */ + <3 13 RK_FUNC_1 &pcfg_pull_none>, + /* mac_txen */ + <3 12 RK_FUNC_1 &pcfg_pull_none_13ma>, + /* mac_clk */ + <3 11 RK_FUNC_1 &pcfg_pull_none>, + /* mac_rxdv */ + <3 9 RK_FUNC_1 &pcfg_pull_none>, + /* mac_mdc */ + <3 8 RK_FUNC_1 &pcfg_pull_none>, + /* mac_rxd1 */ + <3 7 RK_FUNC_1 &pcfg_pull_none>, + /* mac_rxd0 */ + <3 6 RK_FUNC_1 &pcfg_pull_none>, + /* mac_txd1 */ + <3 5 RK_FUNC_1 &pcfg_pull_none_13ma>, + /* mac_txd0 */ + <3 4 RK_FUNC_1 &pcfg_pull_none_13ma>, + /* mac_rxd3 */ + <3 3 RK_FUNC_1 &pcfg_pull_none>, + /* mac_rxd2 */ + <3 2 RK_FUNC_1 &pcfg_pull_none>, + /* mac_txd3 */ + <3 1 RK_FUNC_1 &pcfg_pull_none_13ma>, + /* mac_txd2 */ + <3 0 RK_FUNC_1 &pcfg_pull_none_13ma>; + }; + + rmii_pins: rmii-pins { + rockchip,pins = + /* mac_mdio */ + <3 13 RK_FUNC_1 &pcfg_pull_none>, + /* mac_txen */ + <3 12 RK_FUNC_1 &pcfg_pull_none_13ma>, + /* mac_clk */ + <3 11 RK_FUNC_1 &pcfg_pull_none>, + /* mac_rxer */ + <3 10 RK_FUNC_1 &pcfg_pull_none>, + /* mac_rxdv */ + <3 9 RK_FUNC_1 &pcfg_pull_none>, + /* mac_mdc */ + <3 8 RK_FUNC_1 &pcfg_pull_none>, + /* mac_rxd1 */ + <3 7 RK_FUNC_1 &pcfg_pull_none>, + /* mac_rxd0 */ + <3 6 RK_FUNC_1 &pcfg_pull_none>, + /* mac_txd1 */ + <3 5 RK_FUNC_1 &pcfg_pull_none_13ma>, + /* mac_txd0 */ + <3 4 RK_FUNC_1 &pcfg_pull_none_13ma>; + }; + }; + i2c0 { i2c0_xfer: i2c0-xfer { rockchip,pins = @@ -1326,5 +1814,18 @@ <1 14 RK_FUNC_1 &pcfg_pull_none>; }; }; + + pcie { + pcie_clkreqn: pci-clkreqn { + rockchip,pins = + <2 26 RK_FUNC_2 &pcfg_pull_none>; + }; + + pcie_clkreqnb: pci-clkreqnb { + rockchip,pins = + <4 24 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + }; }; diff --git a/arch/arm64/boot/dts/socionext/Makefile b/arch/arm64/boot/dts/socionext/Makefile index 299b67ec4d44..5538598b302c 100644 --- a/arch/arm64/boot/dts/socionext/Makefile +++ b/arch/arm64/boot/dts/socionext/Makefile @@ -1,4 +1,6 @@ -dtb-$(CONFIG_ARCH_UNIPHIER) += uniphier-ph1-ld20-ref.dtb +dtb-$(CONFIG_ARCH_UNIPHIER) += \ + uniphier-ld11-ref.dtb \ + uniphier-ld20-ref.dtb always := $(dtb-y) clean-files := *.dtb diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts new file mode 100644 index 000000000000..7168cf818ad8 --- /dev/null +++ b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts @@ -0,0 +1,100 @@ +/* + * Device Tree Source for UniPhier LD11 Reference Board + * + * Copyright (C) 2016 Socionext Inc. + * Author: Masahiro Yamada <yamada.masahiro@socionext.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +/include/ "uniphier-ld11.dtsi" +/include/ "uniphier-ref-daughter.dtsi" +/include/ "uniphier-support-card.dtsi" + +/ { + model = "UniPhier LD11 Reference Board"; + compatible = "socionext,uniphier-ld11-ref", "socionext,uniphier-ld11"; + + memory { + device_type = "memory"; + reg = <0 0x80000000 0 0x40000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + serial3 = &serial3; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + }; +}; + +ðsc { + interrupts = <0 48 4>; +}; + +&serial0 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi new file mode 100644 index 000000000000..3eb4c42ce7b9 --- /dev/null +++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi @@ -0,0 +1,338 @@ +/* + * Device Tree Source for UniPhier LD11 SoC + * + * Copyright (C) 2016 Socionext Inc. + * Author: Masahiro Yamada <yamada.masahiro@socionext.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/memreserve/ 0x80000000 0x00000008; /* cpu-release-addr */ + +/ { + compatible = "socionext,uniphier-ld11"; + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&gic>; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu0>; + }; + core1 { + cpu = <&cpu1>; + }; + }; + }; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0 0x000>; + enable-method = "spin-table"; + cpu-release-addr = <0 0x80000000>; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0 0x001>; + enable-method = "spin-table"; + cpu-release-addr = <0 0x80000000>; + }; + }; + + clocks { + refclk: ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 13 4>, + <1 14 4>, + <1 11 4>, + <1 10 4>; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + + serial0: serial@54006800 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x54006800 0x40>; + interrupts = <0 33 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0>; + clocks = <&peri_clk 0>; + }; + + serial1: serial@54006900 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x54006900 0x40>; + interrupts = <0 35 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + clocks = <&peri_clk 1>; + }; + + serial2: serial@54006a00 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x54006a00 0x40>; + interrupts = <0 37 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + clocks = <&peri_clk 2>; + }; + + serial3: serial@54006b00 { + compatible = "socionext,uniphier-uart"; + status = "disabled"; + reg = <0x54006b00 0x40>; + interrupts = <0 177 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + clocks = <&peri_clk 3>; + }; + + i2c0: i2c@58780000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58780000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0>; + clocks = <&peri_clk 4>; + clock-frequency = <100000>; + }; + + i2c1: i2c@58781000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58781000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 42 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clocks = <&peri_clk 5>; + clock-frequency = <100000>; + }; + + i2c2: i2c@58782000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58782000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 43 4>; + clocks = <&peri_clk 6>; + clock-frequency = <400000>; + }; + + i2c3: i2c@58783000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58783000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 44 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clocks = <&peri_clk 7>; + clock-frequency = <100000>; + }; + + i2c4: i2c@58784000 { + compatible = "socionext,uniphier-fi2c"; + status = "disabled"; + reg = <0x58784000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 45 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + clocks = <&peri_clk 8>; + clock-frequency = <100000>; + }; + + i2c5: i2c@58785000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58785000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 25 4>; + clocks = <&peri_clk 9>; + clock-frequency = <400000>; + }; + + system_bus: system-bus@58c00000 { + compatible = "socionext,uniphier-system-bus"; + status = "disabled"; + reg = <0x58c00000 0x400>; + #address-cells = <2>; + #size-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_system_bus>; + }; + + smpctrl@59800000 { + compatible = "socionext,uniphier-smpctrl"; + reg = <0x59801000 0x400>; + }; + + perictrl@59820000 { + compatible = "socionext,uniphier-perictrl", + "simple-mfd", "syscon"; + reg = <0x59820000 0x200>; + + peri_clk: clock { + compatible = "socionext,uniphier-ld11-peri-clock"; + #clock-cells = <1>; + }; + + peri_rst: reset { + compatible = "socionext,uniphier-ld11-peri-reset"; + #reset-cells = <1>; + }; + }; + + usb0: usb@5a800100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a800100 0x100>; + interrupts = <0 243 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0>; + clocks = <&mio_clk 7>, <&mio_clk 8>, <&mio_clk 12>; + resets = <&mio_rst 7>, <&mio_rst 8>, <&mio_rst 12>, <&sys_rst 8>; + }; + + usb1: usb@5a810100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a810100 0x100>; + interrupts = <0 244 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1>; + clocks = <&mio_clk 7>, <&mio_clk 9>, <&mio_clk 13>; + resets = <&mio_rst 7>, <&mio_rst 9>, <&mio_rst 13>, <&sys_rst 8>; + }; + + usb2: usb@5a820100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + status = "disabled"; + reg = <0x5a820100 0x100>; + interrupts = <0 245 4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb2>; + clocks = <&mio_clk 7>, <&mio_clk 10>, <&mio_clk 14>; + resets = <&mio_rst 7>, <&mio_rst 10>, <&mio_rst 14>, <&sys_rst 8>; + }; + + mioctrl@5b3e0000 { + compatible = "socionext,uniphier-mioctrl", + "simple-mfd", "syscon"; + reg = <0x5b3e0000 0x800>; + + mio_clk: clock { + compatible = "socionext,uniphier-ld11-mio-clock"; + #clock-cells = <1>; + }; + + mio_rst: reset { + compatible = "socionext,uniphier-ld11-mio-reset"; + #reset-cells = <1>; + resets = <&sys_rst 7>; + }; + }; + + soc-glue@5f800000 { + compatible = "socionext,uniphier-soc-glue", + "simple-mfd", "syscon"; + reg = <0x5f800000 0x2000>; + + pinctrl: pinctrl { + compatible = "socionext,uniphier-ld11-pinctrl"; + }; + }; + + gic: interrupt-controller@5fe00000 { + compatible = "arm,gic-v3"; + reg = <0x5fe00000 0x10000>, /* GICD */ + <0x5fe40000 0x80000>; /* GICR */ + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <1 9 4>; + }; + + sysctrl@61840000 { + compatible = "socionext,uniphier-ld11-sysctrl", + "simple-mfd", "syscon"; + reg = <0x61840000 0x4000>; + + sys_clk: clock { + compatible = "socionext,uniphier-ld11-clock"; + #clock-cells = <1>; + }; + + sys_rst: reset { + compatible = "socionext,uniphier-ld11-reset"; + #reset-cells = <1>; + }; + }; + }; +}; + +/include/ "uniphier-pinctrl.dtsi" diff --git a/arch/arm64/boot/dts/socionext/uniphier-ph1-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts index 2adad8c8cd27..609162a1a322 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ph1-ld20-ref.dts +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts @@ -1,7 +1,8 @@ /* - * Device Tree Source for UniPhier PH1-LD20 Reference Board + * Device Tree Source for UniPhier LD20 Reference Board * - * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com> + * Copyright (C) 2015-2016 Socionext Inc. + * Author: Masahiro Yamada <yamada.masahiro@socionext.com> * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -43,13 +44,13 @@ */ /dts-v1/; -/include/ "uniphier-ph1-ld20.dtsi" +/include/ "uniphier-ld20.dtsi" /include/ "uniphier-ref-daughter.dtsi" /include/ "uniphier-support-card.dtsi" / { - model = "UniPhier PH1-LD20 Reference Board"; - compatible = "socionext,ph1-ld20-ref", "socionext,ph1-ld20"; + model = "UniPhier LD20 Reference Board"; + compatible = "socionext,uniphier-ld20-ref", "socionext,uniphier-ld20"; memory { device_type = "memory"; diff --git a/arch/arm64/boot/dts/socionext/uniphier-ph1-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi index d73bdc8c9115..08fd7cf7769c 100644 --- a/arch/arm64/boot/dts/socionext/uniphier-ph1-ld20.dtsi +++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi @@ -1,7 +1,8 @@ /* - * Device Tree Source for UniPhier PH1-LD20 SoC + * Device Tree Source for UniPhier LD20 SoC * - * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com> + * Copyright (C) 2015-2016 Socionext Inc. + * Author: Masahiro Yamada <yamada.masahiro@socionext.com> * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -45,7 +46,7 @@ /memreserve/ 0x80000000 0x00000008; /* cpu-release-addr */ / { - compatible = "socionext,ph1-ld20"; + compatible = "socionext,uniphier-ld20"; #address-cells = <2>; #size-cells = <2>; interrupt-parent = <&gic>; @@ -113,18 +114,6 @@ #clock-cells = <0>; clock-frequency = <25000000>; }; - - uart_clk: uart_clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <58820000>; - }; - - i2c_clk: i2c_clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <50000000>; - }; }; timer { @@ -148,7 +137,7 @@ interrupts = <0 33 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart0>; - clocks = <&uart_clk>; + clocks = <&peri_clk 0>; }; serial1: serial@54006900 { @@ -158,7 +147,7 @@ interrupts = <0 35 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; - clocks = <&uart_clk>; + clocks = <&peri_clk 1>; }; serial2: serial@54006a00 { @@ -168,7 +157,7 @@ interrupts = <0 37 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; - clocks = <&uart_clk>; + clocks = <&peri_clk 2>; }; serial3: serial@54006b00 { @@ -178,7 +167,7 @@ interrupts = <0 177 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart3>; - clocks = <&uart_clk>; + clocks = <&peri_clk 3>; }; i2c0: i2c@58780000 { @@ -190,7 +179,7 @@ interrupts = <0 41 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c0>; - clocks = <&i2c_clk>; + clocks = <&peri_clk 4>; clock-frequency = <100000>; }; @@ -203,7 +192,7 @@ interrupts = <0 42 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c1>; - clocks = <&i2c_clk>; + clocks = <&peri_clk 5>; clock-frequency = <100000>; }; @@ -213,7 +202,7 @@ #address-cells = <1>; #size-cells = <0>; interrupts = <0 43 4>; - clocks = <&i2c_clk>; + clocks = <&peri_clk 6>; clock-frequency = <400000>; }; @@ -226,7 +215,7 @@ interrupts = <0 44 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c3>; - clocks = <&i2c_clk>; + clocks = <&peri_clk 7>; clock-frequency = <100000>; }; @@ -239,7 +228,7 @@ interrupts = <0 45 4>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c4>; - clocks = <&i2c_clk>; + clocks = <&peri_clk 8>; clock-frequency = <100000>; }; @@ -249,7 +238,7 @@ #address-cells = <1>; #size-cells = <0>; interrupts = <0 25 4>; - clocks = <&i2c_clk>; + clocks = <&peri_clk 9>; clock-frequency = <400000>; }; @@ -259,6 +248,8 @@ reg = <0x58c00000 0x400>; #address-cells = <2>; #size-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_system_bus>; }; smpctrl@59800000 { @@ -266,12 +257,45 @@ reg = <0x59801000 0x400>; }; + mioctrl@59810000 { + compatible = "socionext,uniphier-mioctrl", + "simple-mfd", "syscon"; + reg = <0x59810000 0x800>; + + mio_clk: clock { + compatible = "socionext,uniphier-ld20-mio-clock"; + #clock-cells = <1>; + }; + + mio_rst: reset { + compatible = "socionext,uniphier-ld20-mio-reset"; + #reset-cells = <1>; + }; + }; + + perictrl@59820000 { + compatible = "socionext,uniphier-perictrl", + "simple-mfd", "syscon"; + reg = <0x59820000 0x200>; + + peri_clk: clock { + compatible = "socionext,uniphier-ld20-peri-clock"; + #clock-cells = <1>; + }; + + peri_rst: reset { + compatible = "socionext,uniphier-ld20-peri-reset"; + #reset-cells = <1>; + }; + }; + soc-glue@5f800000 { - compatible = "simple-mfd", "syscon"; + compatible = "socionext,uniphier-soc-glue", + "simple-mfd", "syscon"; reg = <0x5f800000 0x2000>; pinctrl: pinctrl { - compatible = "socionext,uniphier-ld20-pinctrl"; + compatible = "socionext,uniphier-ld20-pinctrl"; }; }; @@ -283,6 +307,22 @@ #interrupt-cells = <3>; interrupts = <1 9 4>; }; + + sysctrl@61840000 { + compatible = "socionext,uniphier-sysctrl", + "simple-mfd", "syscon"; + reg = <0x61840000 0x4000>; + + sys_clk: clock { + compatible = "socionext,uniphier-ld20-clock"; + #clock-cells = <1>; + }; + + sys_rst: reset { + compatible = "socionext,uniphier-ld20-reset"; + #reset-cells = <1>; + }; + }; }; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts b/arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts index acb0527fdc4a..358089687a69 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-ep108.dts @@ -29,7 +29,7 @@ memory { device_type = "memory"; - reg = <0x0 0x0 0x40000000>; + reg = <0x0 0x0 0x0 0x40000000>; }; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 3e2e51fbd2bc..68a908334c7b 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -14,7 +14,7 @@ / { compatible = "xlnx,zynqmp"; #address-cells = <2>; - #size-cells = <1>; + #size-cells = <2>; cpus { #address-cells = <1>; @@ -51,6 +51,7 @@ pmu { compatible = "arm,armv8-pmuv3"; + interrupt-parent = <&gic>; interrupts = <0 143 4>, <0 144 4>, <0 145 4>, @@ -75,15 +76,15 @@ compatible = "simple-bus"; #address-cells = <2>; #size-cells = <1>; - ranges; + ranges = <0 0 0 0 0xffffffff>; gic: interrupt-controller@f9010000 { compatible = "arm,gic-400", "arm,cortex-a15-gic"; #interrupt-cells = <3>; reg = <0x0 0xf9010000 0x10000>, - <0x0 0xf902f000 0x2000>, + <0x0 0xf9020000 0x20000>, <0x0 0xf9040000 0x20000>, - <0x0 0xf906f000 0x2000>; + <0x0 0xf9060000 0x20000>; interrupt-controller; interrupt-parent = <&gic>; interrupts = <1 9 0xf04>; @@ -93,14 +94,14 @@ amba: amba { compatible = "simple-bus"; #address-cells = <2>; - #size-cells = <1>; + #size-cells = <2>; ranges; can0: can@ff060000 { compatible = "xlnx,zynq-can-1.0"; status = "disabled"; clock-names = "can_clk", "pclk"; - reg = <0x0 0xff060000 0x1000>; + reg = <0x0 0xff060000 0x0 0x1000>; interrupts = <0 23 4>; interrupt-parent = <&gic>; tx-fifo-depth = <0x40>; @@ -111,7 +112,7 @@ compatible = "xlnx,zynq-can-1.0"; status = "disabled"; clock-names = "can_clk", "pclk"; - reg = <0x0 0xff070000 0x1000>; + reg = <0x0 0xff070000 0x0 0x1000>; interrupts = <0 24 4>; interrupt-parent = <&gic>; tx-fifo-depth = <0x40>; @@ -123,7 +124,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 57 4>, <0 57 4>; - reg = <0x0 0xff0b0000 0x1000>; + reg = <0x0 0xff0b0000 0x0 0x1000>; clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; @@ -134,7 +135,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 59 4>, <0 59 4>; - reg = <0x0 0xff0c0000 0x1000>; + reg = <0x0 0xff0c0000 0x0 0x1000>; clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; @@ -145,7 +146,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 61 4>, <0 61 4>; - reg = <0x0 0xff0d0000 0x1000>; + reg = <0x0 0xff0d0000 0x0 0x1000>; clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; @@ -156,7 +157,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 63 4>, <0 63 4>; - reg = <0x0 0xff0e0000 0x1000>; + reg = <0x0 0xff0e0000 0x0 0x1000>; clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; @@ -170,7 +171,7 @@ interrupts = <0 16 4>; interrupt-controller; #interrupt-cells = <2>; - reg = <0x0 0xff0a0000 0x1000>; + reg = <0x0 0xff0a0000 0x0 0x1000>; }; i2c0: i2c@ff020000 { @@ -178,7 +179,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 17 4>; - reg = <0x0 0xff020000 0x1000>; + reg = <0x0 0xff020000 0x0 0x1000>; #address-cells = <1>; #size-cells = <0>; }; @@ -188,15 +189,54 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 18 4>; - reg = <0x0 0xff030000 0x1000>; + reg = <0x0 0xff030000 0x0 0x1000>; #address-cells = <1>; #size-cells = <0>; }; + pcie: pcie@fd0e0000 { + compatible = "xlnx,nwl-pcie-2.11"; + status = "disabled"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + msi-controller; + device_type = "pci"; + interrupt-parent = <&gic>; + interrupts = <0 118 4>, + <0 117 4>, + <0 116 4>, + <0 115 4>, /* MSI_1 [63...32] */ + <0 114 4>; /* MSI_0 [31...0] */ + interrupt-names = "misc", "dummy", "intx", + "msi1", "msi0"; + msi-parent = <&pcie>; + reg = <0x0 0xfd0e0000 0x0 0x1000>, + <0x0 0xfd480000 0x0 0x1000>, + <0x80 0x00000000 0x0 0x1000000>; + reg-names = "breg", "pcireg", "cfg"; + ranges = <0x02000000 0x00000000 0xe0000000 0x00000000 + 0xe0000000 0x00000000 0x10000000 + /* non-prefetchable memory */ + 0x43000000 0x00000006 0x00000000 0x00000006 + 0x00000000 0x00000002 0x00000000>; + /* prefetchable memory */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc 0x1>, + <0x0 0x0 0x0 0x2 &pcie_intc 0x2>, + <0x0 0x0 0x0 0x3 &pcie_intc 0x3>, + <0x0 0x0 0x0 0x4 &pcie_intc 0x4>; + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + sata: ahci@fd0c0000 { compatible = "ceva,ahci-1v84"; status = "disabled"; - reg = <0x0 0xfd0c0000 0x2000>; + reg = <0x0 0xfd0c0000 0x0 0x2000>; interrupt-parent = <&gic>; interrupts = <0 133 4>; }; @@ -206,7 +246,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 48 4>; - reg = <0x0 0xff160000 0x1000>; + reg = <0x0 0xff160000 0x0 0x1000>; clock-names = "clk_xin", "clk_ahb"; }; @@ -215,13 +255,13 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 49 4>; - reg = <0x0 0xff170000 0x1000>; + reg = <0x0 0xff170000 0x0 0x1000>; clock-names = "clk_xin", "clk_ahb"; }; smmu: smmu@fd800000 { compatible = "arm,mmu-500"; - reg = <0x0 0xfd800000 0x20000>; + reg = <0x0 0xfd800000 0x0 0x20000>; #global-interrupts = <1>; interrupt-parent = <&gic>; interrupts = <0 157 4>, @@ -236,7 +276,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 19 4>; - reg = <0x0 0xff040000 0x1000>; + reg = <0x0 0xff040000 0x0 0x1000>; clock-names = "ref_clk", "pclk"; #address-cells = <1>; #size-cells = <0>; @@ -247,7 +287,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 20 4>; - reg = <0x0 0xff050000 0x1000>; + reg = <0x0 0xff050000 0x0 0x1000>; clock-names = "ref_clk", "pclk"; #address-cells = <1>; #size-cells = <0>; @@ -258,7 +298,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 36 4>, <0 37 4>, <0 38 4>; - reg = <0x0 0xff110000 0x1000>; + reg = <0x0 0xff110000 0x0 0x1000>; timer-width = <32>; }; @@ -267,7 +307,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 39 4>, <0 40 4>, <0 41 4>; - reg = <0x0 0xff120000 0x1000>; + reg = <0x0 0xff120000 0x0 0x1000>; timer-width = <32>; }; @@ -276,7 +316,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 42 4>, <0 43 4>, <0 44 4>; - reg = <0x0 0xff130000 0x1000>; + reg = <0x0 0xff130000 0x0 0x1000>; timer-width = <32>; }; @@ -285,7 +325,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 45 4>, <0 46 4>, <0 47 4>; - reg = <0x0 0xff140000 0x1000>; + reg = <0x0 0xff140000 0x0 0x1000>; timer-width = <32>; }; @@ -294,7 +334,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 21 4>; - reg = <0x0 0xff000000 0x1000>; + reg = <0x0 0xff000000 0x0 0x1000>; clock-names = "uart_clk", "pclk"; }; @@ -303,7 +343,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 22 4>; - reg = <0x0 0xff010000 0x1000>; + reg = <0x0 0xff010000 0x0 0x1000>; clock-names = "uart_clk", "pclk"; }; @@ -312,7 +352,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 65 4>; - reg = <0x0 0xfe200000 0x40000>; + reg = <0x0 0xfe200000 0x0 0x40000>; clock-names = "clk_xin", "clk_ahb"; }; @@ -321,7 +361,7 @@ status = "disabled"; interrupt-parent = <&gic>; interrupts = <0 70 4>; - reg = <0x0 0xfe300000 0x40000>; + reg = <0x0 0xfe300000 0x0 0x40000>; clock-names = "clk_xin", "clk_ahb"; }; @@ -329,8 +369,8 @@ compatible = "cdns,wdt-r1p2"; status = "disabled"; interrupt-parent = <&gic>; - interrupts = <0 52 1>; - reg = <0x0 0xfd4d0000 0x1000>; + interrupts = <0 113 1>; + reg = <0x0 0xfd4d0000 0x0 0x1000>; timeout-sec = <10>; }; }; diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 0555b7caaf2c..eadf4855ad2d 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -1,4 +1,3 @@ -# CONFIG_LOCALVERSION_AUTO is not set CONFIG_SYSVIPC=y CONFIG_POSIX_MQUEUE=y CONFIG_AUDIT=y @@ -15,10 +14,14 @@ CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 CONFIG_MEMCG=y CONFIG_MEMCG_SWAP=y +CONFIG_BLK_CGROUP=y +CONFIG_CGROUP_PIDS=y CONFIG_CGROUP_HUGETLB=y -# CONFIG_UTS_NS is not set -# CONFIG_IPC_NS is not set -# CONFIG_NET_NS is not set +CONFIG_CPUSETS=y +CONFIG_CGROUP_DEVICE=y +CONFIG_CGROUP_CPUACCT=y +CONFIG_CGROUP_PERF=y +CONFIG_USER_NS=y CONFIG_SCHED_AUTOGROUP=y CONFIG_BLK_DEV_INITRD=y CONFIG_KALLSYMS_ALL=y @@ -71,6 +74,7 @@ CONFIG_PREEMPT=y CONFIG_KSM=y CONFIG_TRANSPARENT_HUGEPAGE=y CONFIG_CMA=y +CONFIG_SECCOMP=y CONFIG_XEN=y CONFIG_KEXEC=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set @@ -84,10 +88,37 @@ CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y CONFIG_INET=y +CONFIG_IP_MULTICAST=y CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y -# CONFIG_IPV6 is not set +CONFIG_IPV6=m +CONFIG_NETFILTER=y +CONFIG_NF_CONNTRACK=m +CONFIG_NF_CONNTRACK_EVENTS=y +CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m +CONFIG_NETFILTER_XT_TARGET_LOG=m +CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m +CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m +CONFIG_NF_CONNTRACK_IPV4=m +CONFIG_IP_NF_IPTABLES=m +CONFIG_IP_NF_FILTER=m +CONFIG_IP_NF_TARGET_REJECT=m +CONFIG_IP_NF_NAT=m +CONFIG_IP_NF_TARGET_MASQUERADE=m +CONFIG_IP_NF_MANGLE=m +CONFIG_NF_CONNTRACK_IPV6=m +CONFIG_IP6_NF_IPTABLES=m +CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_TARGET_REJECT=m +CONFIG_IP6_NF_MANGLE=m +CONFIG_IP6_NF_NAT=m +CONFIG_IP6_NF_TARGET_MASQUERADE=m +CONFIG_BRIDGE=m +CONFIG_BRIDGE_VLAN_FILTERING=y +CONFIG_VLAN_8021Q=m +CONFIG_VLAN_8021Q_GVRP=y +CONFIG_VLAN_8021Q_MVRP=y CONFIG_BPF_JIT=y CONFIG_CFG80211=m CONFIG_MAC80211=m @@ -103,6 +134,7 @@ CONFIG_MTD=y CONFIG_MTD_M25P80=y CONFIG_MTD_SPI_NOR=y CONFIG_BLK_DEV_LOOP=y +CONFIG_BLK_DEV_NBD=m CONFIG_VIRTIO_BLK=y CONFIG_SRAM=y # CONFIG_SCSI_PROC_FS is not set @@ -120,7 +152,10 @@ CONFIG_SATA_SIL24=y CONFIG_PATA_PLATFORM=y CONFIG_PATA_OF_PLATFORM=y CONFIG_NETDEVICES=y +CONFIG_MACVLAN=m +CONFIG_MACVTAP=m CONFIG_TUN=y +CONFIG_VETH=m CONFIG_VIRTIO_NET=y CONFIG_AMD_XGBE=y CONFIG_NET_XGENE=y @@ -350,12 +385,16 @@ CONFIG_EXYNOS_ADC=y CONFIG_PWM_SAMSUNG=y CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y +CONFIG_EXT4_FS_POSIX_ACL=y +CONFIG_BTRFS_FS=m +CONFIG_BTRFS_FS_POSIX_ACL=y CONFIG_FANOTIFY=y CONFIG_FANOTIFY_ACCESS_PERMISSIONS=y CONFIG_QUOTA=y CONFIG_AUTOFS4_FS=y -CONFIG_FUSE_FS=y -CONFIG_CUSE=y +CONFIG_FUSE_FS=m +CONFIG_CUSE=m +CONFIG_OVERLAY_FS=m CONFIG_VFAT_FS=y CONFIG_TMPFS=y CONFIG_HUGETLBFS=y diff --git a/arch/arm64/include/asm/kprobes.h b/arch/arm64/include/asm/kprobes.h index 61b49150dfa3..1737aecfcc5e 100644 --- a/arch/arm64/include/asm/kprobes.h +++ b/arch/arm64/include/asm/kprobes.h @@ -22,7 +22,6 @@ #define __ARCH_WANT_KPROBES_INSN_SLOT #define MAX_INSN_SIZE 1 -#define MAX_STACK_SIZE 128 #define flush_insn_slot(p) do { } while (0) #define kretprobe_blacklist_size 0 @@ -47,7 +46,6 @@ struct kprobe_ctlblk { struct prev_kprobe prev_kprobe; struct kprobe_step_ctx ss_ctx; struct pt_regs jprobe_saved_regs; - char jprobes_stack[MAX_STACK_SIZE]; }; void arch_remove_kprobe(struct kprobe *); diff --git a/arch/arm64/include/asm/uaccess.h b/arch/arm64/include/asm/uaccess.h index 5e834d10b291..c47257c91b77 100644 --- a/arch/arm64/include/asm/uaccess.h +++ b/arch/arm64/include/asm/uaccess.h @@ -265,22 +265,25 @@ extern unsigned long __must_check __clear_user(void __user *addr, unsigned long static inline unsigned long __must_check __copy_from_user(void *to, const void __user *from, unsigned long n) { kasan_check_write(to, n); - return __arch_copy_from_user(to, from, n); + check_object_size(to, n, false); + return __arch_copy_from_user(to, from, n); } static inline unsigned long __must_check __copy_to_user(void __user *to, const void *from, unsigned long n) { kasan_check_read(from, n); - return __arch_copy_to_user(to, from, n); + check_object_size(from, n, true); + return __arch_copy_to_user(to, from, n); } static inline unsigned long __must_check copy_from_user(void *to, const void __user *from, unsigned long n) { kasan_check_write(to, n); - if (access_ok(VERIFY_READ, from, n)) + if (access_ok(VERIFY_READ, from, n)) { + check_object_size(to, n, false); n = __arch_copy_from_user(to, from, n); - else /* security hole - plug it */ + } else /* security hole - plug it */ memset(to, 0, n); return n; } @@ -289,8 +292,10 @@ static inline unsigned long __must_check copy_to_user(void __user *to, const voi { kasan_check_read(from, n); - if (access_ok(VERIFY_WRITE, to, n)) + if (access_ok(VERIFY_WRITE, to, n)) { + check_object_size(from, n, true); n = __arch_copy_to_user(to, from, n); + } return n; } diff --git a/arch/arm64/kernel/entry.S b/arch/arm64/kernel/entry.S index 96e4a2b64cc1..441420ca7d08 100644 --- a/arch/arm64/kernel/entry.S +++ b/arch/arm64/kernel/entry.S @@ -353,6 +353,8 @@ el1_sync: lsr x24, x1, #ESR_ELx_EC_SHIFT // exception class cmp x24, #ESR_ELx_EC_DABT_CUR // data abort in EL1 b.eq el1_da + cmp x24, #ESR_ELx_EC_IABT_CUR // instruction abort in EL1 + b.eq el1_ia cmp x24, #ESR_ELx_EC_SYS64 // configurable trap b.eq el1_undef cmp x24, #ESR_ELx_EC_SP_ALIGN // stack alignment exception @@ -364,6 +366,11 @@ el1_sync: cmp x24, #ESR_ELx_EC_BREAKPT_CUR // debug exception in EL1 b.ge el1_dbg b el1_inv + +el1_ia: + /* + * Fall through to the Data abort case + */ el1_da: /* * Data abort handling diff --git a/arch/arm64/kernel/head.S b/arch/arm64/kernel/head.S index b77f58355da1..3e7b050e99dc 100644 --- a/arch/arm64/kernel/head.S +++ b/arch/arm64/kernel/head.S @@ -757,6 +757,9 @@ ENTRY(__enable_mmu) isb bl __create_page_tables // recreate kernel mapping + tlbi vmalle1 // Remove any stale TLB entries + dsb nsh + msr sctlr_el1, x19 // re-enable the MMU isb ic iallu // flush instructions fetched diff --git a/arch/arm64/kernel/hibernate.c b/arch/arm64/kernel/hibernate.c index 21ab5df9fa76..65d81f965e74 100644 --- a/arch/arm64/kernel/hibernate.c +++ b/arch/arm64/kernel/hibernate.c @@ -35,6 +35,7 @@ #include <asm/sections.h> #include <asm/smp.h> #include <asm/suspend.h> +#include <asm/sysreg.h> #include <asm/virt.h> /* @@ -217,12 +218,22 @@ static int create_safe_exec_page(void *src_start, size_t length, set_pte(pte, __pte(virt_to_phys((void *)dst) | pgprot_val(PAGE_KERNEL_EXEC))); - /* Load our new page tables */ - asm volatile("msr ttbr0_el1, %0;" - "isb;" - "tlbi vmalle1is;" - "dsb ish;" - "isb" : : "r"(virt_to_phys(pgd))); + /* + * Load our new page tables. A strict BBM approach requires that we + * ensure that TLBs are free of any entries that may overlap with the + * global mappings we are about to install. + * + * For a real hibernate/resume cycle TTBR0 currently points to a zero + * page, but TLBs may contain stale ASID-tagged entries (e.g. for EFI + * runtime services), while for a userspace-driven test_resume cycle it + * points to userspace page tables (and we must point it at a zero page + * ourselves). Elsewhere we only (un)install the idmap with preemption + * disabled, so T0SZ should be as required regardless. + */ + cpu_set_reserved_ttbr0(); + local_flush_tlb_all(); + write_sysreg(virt_to_phys(pgd), ttbr0_el1); + isb(); *phys_dst_addr = virt_to_phys((void *)dst); @@ -394,6 +405,38 @@ int swsusp_arch_resume(void) void *, phys_addr_t, phys_addr_t); /* + * Restoring the memory image will overwrite the ttbr1 page tables. + * Create a second copy of just the linear map, and use this when + * restoring. + */ + tmp_pg_dir = (pgd_t *)get_safe_page(GFP_ATOMIC); + if (!tmp_pg_dir) { + pr_err("Failed to allocate memory for temporary page tables."); + rc = -ENOMEM; + goto out; + } + rc = copy_page_tables(tmp_pg_dir, PAGE_OFFSET, 0); + if (rc) + goto out; + + /* + * Since we only copied the linear map, we need to find restore_pblist's + * linear map address. + */ + lm_restore_pblist = LMADDR(restore_pblist); + + /* + * We need a zero page that is zero before & after resume in order to + * to break before make on the ttbr1 page tables. + */ + zero_page = (void *)get_safe_page(GFP_ATOMIC); + if (!zero_page) { + pr_err("Failed to allocate zero page."); + rc = -ENOMEM; + goto out; + } + + /* * Locate the exit code in the bottom-but-one page, so that *NULL * still has disastrous affects. */ @@ -419,27 +462,6 @@ int swsusp_arch_resume(void) __flush_dcache_area(hibernate_exit, exit_size); /* - * Restoring the memory image will overwrite the ttbr1 page tables. - * Create a second copy of just the linear map, and use this when - * restoring. - */ - tmp_pg_dir = (pgd_t *)get_safe_page(GFP_ATOMIC); - if (!tmp_pg_dir) { - pr_err("Failed to allocate memory for temporary page tables."); - rc = -ENOMEM; - goto out; - } - rc = copy_page_tables(tmp_pg_dir, PAGE_OFFSET, 0); - if (rc) - goto out; - - /* - * Since we only copied the linear map, we need to find restore_pblist's - * linear map address. - */ - lm_restore_pblist = LMADDR(restore_pblist); - - /* * KASLR will cause the el2 vectors to be in a different location in * the resumed kernel. Load hibernate's temporary copy into el2. * @@ -453,12 +475,6 @@ int swsusp_arch_resume(void) __hyp_set_vectors(el2_vectors); } - /* - * We need a zero page that is zero before & after resume in order to - * to break before make on the ttbr1 page tables. - */ - zero_page = (void *)get_safe_page(GFP_ATOMIC); - hibernate_exit(virt_to_phys(tmp_pg_dir), resume_hdr.ttbr1_el1, resume_hdr.reenter_kernel, lm_restore_pblist, resume_hdr.__hyp_stub_vectors, virt_to_phys(zero_page)); diff --git a/arch/arm64/kernel/probes/kprobes.c b/arch/arm64/kernel/probes/kprobes.c index bf9768588288..c6b0f40620d8 100644 --- a/arch/arm64/kernel/probes/kprobes.c +++ b/arch/arm64/kernel/probes/kprobes.c @@ -41,18 +41,6 @@ DEFINE_PER_CPU(struct kprobe_ctlblk, kprobe_ctlblk); static void __kprobes post_kprobe_handler(struct kprobe_ctlblk *, struct pt_regs *); -static inline unsigned long min_stack_size(unsigned long addr) -{ - unsigned long size; - - if (on_irq_stack(addr, raw_smp_processor_id())) - size = IRQ_STACK_PTR(raw_smp_processor_id()) - addr; - else - size = (unsigned long)current_thread_info() + THREAD_START_SP - addr; - - return min(size, FIELD_SIZEOF(struct kprobe_ctlblk, jprobes_stack)); -} - static void __kprobes arch_prepare_ss_slot(struct kprobe *p) { /* prepare insn slot */ @@ -489,20 +477,15 @@ int __kprobes setjmp_pre_handler(struct kprobe *p, struct pt_regs *regs) { struct jprobe *jp = container_of(p, struct jprobe, kp); struct kprobe_ctlblk *kcb = get_kprobe_ctlblk(); - long stack_ptr = kernel_stack_pointer(regs); kcb->jprobe_saved_regs = *regs; /* - * As Linus pointed out, gcc assumes that the callee - * owns the argument space and could overwrite it, e.g. - * tailcall optimization. So, to be absolutely safe - * we also save and restore enough stack bytes to cover - * the argument area. + * Since we can't be sure where in the stack frame "stacked" + * pass-by-value arguments are stored we just don't try to + * duplicate any of the stack. Do not use jprobes on functions that + * use more than 64 bytes (after padding each to an 8 byte boundary) + * of arguments, or pass individual arguments larger than 16 bytes. */ - kasan_disable_current(); - memcpy(kcb->jprobes_stack, (void *)stack_ptr, - min_stack_size(stack_ptr)); - kasan_enable_current(); instruction_pointer_set(regs, (unsigned long) jp->entry); preempt_disable(); @@ -554,10 +537,6 @@ int __kprobes longjmp_break_handler(struct kprobe *p, struct pt_regs *regs) } unpause_graph_tracing(); *regs = kcb->jprobe_saved_regs; - kasan_disable_current(); - memcpy((void *)stack_addr, kcb->jprobes_stack, - min_stack_size(stack_addr)); - kasan_enable_current(); preempt_enable_no_resched(); return 1; } diff --git a/arch/arm64/kernel/sleep.S b/arch/arm64/kernel/sleep.S index 9a3aec97ac09..ccf79d849e0a 100644 --- a/arch/arm64/kernel/sleep.S +++ b/arch/arm64/kernel/sleep.S @@ -101,12 +101,20 @@ ENTRY(cpu_resume) bl el2_setup // if in EL2 drop to EL1 cleanly /* enable the MMU early - so we can access sleep_save_stash by va */ adr_l lr, __enable_mmu /* __cpu_setup will return here */ - ldr x27, =_cpu_resume /* __enable_mmu will branch here */ + adr_l x27, _resume_switched /* __enable_mmu will branch here */ adrp x25, idmap_pg_dir adrp x26, swapper_pg_dir b __cpu_setup ENDPROC(cpu_resume) + .pushsection ".idmap.text", "ax" +_resume_switched: + ldr x8, =_cpu_resume + br x8 +ENDPROC(_resume_switched) + .ltorg + .popsection + ENTRY(_cpu_resume) mrs x1, mpidr_el1 adrp x8, mpidr_hash diff --git a/arch/arm64/kernel/smp.c b/arch/arm64/kernel/smp.c index 76a6d9263908..d93d43352504 100644 --- a/arch/arm64/kernel/smp.c +++ b/arch/arm64/kernel/smp.c @@ -661,9 +661,9 @@ void __init smp_init_cpus(void) acpi_table_parse_madt(ACPI_MADT_TYPE_GENERIC_INTERRUPT, acpi_parse_gic_cpu_interface, 0); - if (cpu_count > NR_CPUS) - pr_warn("no. of cores (%d) greater than configured maximum of %d - clipping\n", - cpu_count, NR_CPUS); + if (cpu_count > nr_cpu_ids) + pr_warn("Number of cores (%d) exceeds configured maximum of %d - clipping\n", + cpu_count, nr_cpu_ids); if (!bootcpu_valid) { pr_err("missing boot CPU MPIDR, not enabling secondaries\n"); @@ -677,7 +677,7 @@ void __init smp_init_cpus(void) * with entries in cpu_logical_map while initializing the cpus. * If the cpu set-up fails, invalidate the cpu_logical_map entry. */ - for (i = 1; i < NR_CPUS; i++) { + for (i = 1; i < nr_cpu_ids; i++) { if (cpu_logical_map(i) != INVALID_HWID) { if (smp_cpu_setup(i)) cpu_logical_map(i) = INVALID_HWID; diff --git a/arch/arm64/kvm/hyp/switch.c b/arch/arm64/kvm/hyp/switch.c index ae7855f16ec2..5a84b4562603 100644 --- a/arch/arm64/kvm/hyp/switch.c +++ b/arch/arm64/kvm/hyp/switch.c @@ -256,7 +256,7 @@ static int __hyp_text __guest_run(struct kvm_vcpu *vcpu) /* * We must restore the 32-bit state before the sysregs, thanks - * to Cortex-A57 erratum #852523. + * to erratum #852523 (Cortex-A57) or #853709 (Cortex-A72). */ __sysreg32_restore_state(vcpu); __sysreg_restore_guest_state(guest_ctxt); diff --git a/arch/arm64/kvm/sys_regs.c b/arch/arm64/kvm/sys_regs.c index b0b225ceca18..e51367d159d0 100644 --- a/arch/arm64/kvm/sys_regs.c +++ b/arch/arm64/kvm/sys_regs.c @@ -823,14 +823,6 @@ static bool access_pmuserenr(struct kvm_vcpu *vcpu, struct sys_reg_params *p, * Architected system registers. * Important: Must be sorted ascending by Op0, Op1, CRn, CRm, Op2 * - * We could trap ID_DFR0 and tell the guest we don't support performance - * monitoring. Unfortunately the patch to make the kernel check ID_DFR0 was - * NAKed, so it will read the PMCR anyway. - * - * Therefore we tell the guest we have 0 counters. Unfortunately, we - * must always support PMCCNTR (the cycle counter): we just RAZ/WI for - * all PM registers, which doesn't crash the guest kernel at least. - * * Debug handling: We do trap most, if not all debug related system * registers. The implementation is good enough to ensure that a guest * can use these with minimal performance degradation. The drawback is @@ -1360,7 +1352,7 @@ static const struct sys_reg_desc cp15_regs[] = { { Op1( 0), CRn(10), CRm( 3), Op2( 1), access_vm_reg, NULL, c10_AMAIR1 }, /* ICC_SRE */ - { Op1( 0), CRn(12), CRm(12), Op2( 5), trap_raz_wi }, + { Op1( 0), CRn(12), CRm(12), Op2( 5), access_gic_sre }, { Op1( 0), CRn(13), CRm( 0), Op2( 1), access_vm_reg, NULL, c13_CID }, diff --git a/arch/arm64/mm/dump.c b/arch/arm64/mm/dump.c index f94b80eb295d..9c3e75df2180 100644 --- a/arch/arm64/mm/dump.c +++ b/arch/arm64/mm/dump.c @@ -242,7 +242,7 @@ static void note_page(struct pg_state *st, unsigned long addr, unsigned level, static void walk_pte(struct pg_state *st, pmd_t *pmd, unsigned long start) { - pte_t *pte = pte_offset_kernel(pmd, 0); + pte_t *pte = pte_offset_kernel(pmd, 0UL); unsigned long addr; unsigned i; @@ -254,7 +254,7 @@ static void walk_pte(struct pg_state *st, pmd_t *pmd, unsigned long start) static void walk_pmd(struct pg_state *st, pud_t *pud, unsigned long start) { - pmd_t *pmd = pmd_offset(pud, 0); + pmd_t *pmd = pmd_offset(pud, 0UL); unsigned long addr; unsigned i; @@ -271,7 +271,7 @@ static void walk_pmd(struct pg_state *st, pud_t *pud, unsigned long start) static void walk_pud(struct pg_state *st, pgd_t *pgd, unsigned long start) { - pud_t *pud = pud_offset(pgd, 0); + pud_t *pud = pud_offset(pgd, 0UL); unsigned long addr; unsigned i; diff --git a/arch/arm64/mm/fault.c b/arch/arm64/mm/fault.c index c8beaa0da7df..05d2bd776c69 100644 --- a/arch/arm64/mm/fault.c +++ b/arch/arm64/mm/fault.c @@ -153,6 +153,11 @@ int ptep_set_access_flags(struct vm_area_struct *vma, } #endif +static bool is_el1_instruction_abort(unsigned int esr) +{ + return ESR_ELx_EC(esr) == ESR_ELx_EC_IABT_CUR; +} + /* * The kernel tried to access some page that wasn't present. */ @@ -161,8 +166,9 @@ static void __do_kernel_fault(struct mm_struct *mm, unsigned long addr, { /* * Are we prepared to handle this kernel fault? + * We are almost certainly not prepared to handle instruction faults. */ - if (fixup_exception(regs)) + if (!is_el1_instruction_abort(esr) && fixup_exception(regs)) return; /* @@ -267,7 +273,8 @@ static inline bool is_permission_fault(unsigned int esr) unsigned int ec = ESR_ELx_EC(esr); unsigned int fsc_type = esr & ESR_ELx_FSC_TYPE; - return (ec == ESR_ELx_EC_DABT_CUR && fsc_type == ESR_ELx_FSC_PERM); + return (ec == ESR_ELx_EC_DABT_CUR && fsc_type == ESR_ELx_FSC_PERM) || + (ec == ESR_ELx_EC_IABT_CUR && fsc_type == ESR_ELx_FSC_PERM); } static bool is_el0_instruction_abort(unsigned int esr) @@ -312,6 +319,9 @@ static int __kprobes do_page_fault(unsigned long addr, unsigned int esr, if (regs->orig_addr_limit == KERNEL_DS) die("Accessing user space memory with fs=KERNEL_DS", regs, esr); + if (is_el1_instruction_abort(esr)) + die("Attempting to execute userspace memory", regs, esr); + if (!search_exception_tables(regs->pc)) die("Accessing user space memory outside uaccess.h routines", regs, esr); } diff --git a/arch/arm64/mm/numa.c b/arch/arm64/mm/numa.c index c7fe3ec70774..5bb15eab6f00 100644 --- a/arch/arm64/mm/numa.c +++ b/arch/arm64/mm/numa.c @@ -23,6 +23,8 @@ #include <linux/module.h> #include <linux/of.h> +#include <asm/acpi.h> + struct pglist_data *node_data[MAX_NUMNODES] __read_mostly; EXPORT_SYMBOL(node_data); nodemask_t numa_nodes_parsed __initdata; |