diff options
Diffstat (limited to 'arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts')
| -rw-r--r-- | arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts | 238 |
1 files changed, 238 insertions, 0 deletions
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts new file mode 100644 index 000000000000..8dbe717c79ce --- /dev/null +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts @@ -0,0 +1,238 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org> + +/* + * gpio line names + * + * The Nezha-D1 has a 40-pin IO header. Some of these pins are routed + * directly to pads on the SoC, others come from an 8-bit pcf857x IO + * expander. Therefore, these line names are specified in two places: + * one set for the pcf857x, and one set for the pio controller. + * + * Lines which are routed to the 40-pin header are named as follows: + * <pin#> [<pin name>] + * where: + * <pin#> is the actual pin number of the 40-pin header + * <pin name> is the name of the pin by function/gpio# + * + * For details regarding pin numbers and names see the schematics (under + * "IO EXPAND"): + * http://dl.linux-sunxi.org/D1/D1_Nezha_development_board_schematic_diagram_20210224.pdf + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/dts-v1/; + +#include "sun20i-d1.dtsi" +#include "sun20i-common-regulators.dtsi" + +/ { + model = "Allwinner D1 Nezha"; + compatible = "allwinner,d1-nezha", "allwinner,sun20i-d1"; + + aliases { + ethernet0 = &emac; + ethernet1 = &xr829; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_usbvbus: usbvbus { + compatible = "regulator-fixed"; + regulator-name = "usbvbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */ + enable-active-high; + vin-supply = <®_vcc>; + }; + + /* + * This regulator is PWM-controlled, but the PWM controller is not + * yet supported, so fix the regulator to its default voltage. + */ + reg_vdd_cpu: vdd-cpu { + compatible = "regulator-fixed"; + regulator-name = "vdd-cpu"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + vin-supply = <®_vcc>; + }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */ + }; +}; + +&cpu0 { + cpu-supply = <®_vdd_cpu>; +}; + +&dcxo { + clock-frequency = <24000000>; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&emac { + pinctrl-0 = <&rgmii_pe_pins>; + pinctrl-names = "default"; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii-id"; + phy-supply = <®_vcc_3v3>; + status = "okay"; +}; + +&i2c2 { + pinctrl-0 = <&i2c2_pb0_pins>; + pinctrl-names = "default"; + status = "okay"; + + pcf8574a: gpio@38 { + compatible = "nxp,pcf8574a"; + reg = <0x38>; + interrupt-parent = <&pio>; + interrupts = <1 2 IRQ_TYPE_LEVEL_LOW>; /* PB2 */ + interrupt-controller; + gpio-controller; + #gpio-cells = <2>; + #interrupt-cells = <2>; + gpio-line-names = + "pin13 [gpio8]", + "pin16 [gpio10]", + "pin18 [gpio11]", + "pin26 [gpio17]", + "pin22 [gpio14]", + "pin28 [gpio19]", + "pin37 [gpio23]", + "pin11 [gpio6]"; + }; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mmc0 { + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + disable-wp; + vmmc-supply = <®_vcc_3v3>; + vqmmc-supply = <®_vcc_3v3>; + pinctrl-0 = <&mmc0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&mmc1 { + bus-width = <4>; + mmc-pwrseq = <&wifi_pwrseq>; + non-removable; + vmmc-supply = <®_vcc_3v3>; + vqmmc-supply = <®_vcc_3v3>; + pinctrl-0 = <&mmc1_pins>; + pinctrl-names = "default"; + status = "okay"; + + xr829: wifi@1 { + reg = <1>; + interrupt-parent = <&pio>; + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */ + interrupt-names = "host-wake"; + }; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&uart0 { + pinctrl-0 = <&uart0_pb8_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&uart1 { + uart-has-rtscts; + pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>; + pinctrl-names = "default"; + status = "okay"; + + /* XR829 bluetooth is connected here */ +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 3 21 GPIO_ACTIVE_HIGH>; /* PD21 */ + usb0_vbus_det-gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */ + usb0_vbus-supply = <®_usbvbus>; + usb1_vbus-supply = <®_vcc>; + status = "okay"; +}; + +&pio { + gpio-line-names = + /* Port A */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* Port B */ + "pin5 [gpio2/twi2-sck]", + "pin3 [gpio1/twi2-sda]", + "", + "pin38 [gpio24/i2s2-din]", + "pin40 [gpio25/i2s2-dout]", + "pin12 [gpio7/i2s-clk]", + "pin35 [gpio22/i2s2-lrck]", + "", + "pin8 [gpio4/uart0-txd]", + "pin10 [gpio5/uart0-rxd]", + "", + "", + "pin15 [gpio9]", + "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* Port C */ + "", + "pin31 [gpio21]", + "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* Port D */ + "", "", "", "", "", "", "", "", + "", "", + "pin24 [gpio16/spi1-ce0]", + "pin23 [gpio15/spi1-clk]", + "pin19 [gpio12/spi1-mosi]", + "pin21 [gpio13/spi1-miso]", + "pin27 [gpio18/spi1-hold]", + "pin29 [gpio20/spi1-wp]", + "", "", "", "", "", "", + "pin7 [gpio3/pwm]"; +}; |