summaryrefslogtreecommitdiff
path: root/drivers/ata/pata_sl82c105.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ata/pata_sl82c105.c')
-rw-r--r--drivers/ata/pata_sl82c105.c48
1 files changed, 24 insertions, 24 deletions
diff --git a/drivers/ata/pata_sl82c105.c b/drivers/ata/pata_sl82c105.c
index 47b290b5604a..f8499786917a 100644
--- a/drivers/ata/pata_sl82c105.c
+++ b/drivers/ata/pata_sl82c105.c
@@ -8,7 +8,7 @@
*
* and in part on the documentation and errata sheet
*/
-
+
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
@@ -40,7 +40,7 @@ enum {
*
* Set up cable type and use generic probe init
*/
-
+
static int sl82c105_pre_reset(struct ata_port *ap)
{
static const struct pci_bits sl82c105_enable_bits[] = {
@@ -75,7 +75,7 @@ static void sl82c105_error_handler(struct ata_port *ap)
* so a configure_dmamode call will undo any work we do here and vice
* versa
*/
-
+
static void sl82c105_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
@@ -84,7 +84,7 @@ static void sl82c105_configure_piomode(struct ata_port *ap, struct ata_device *a
};
u16 dummy;
int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
-
+
pci_write_config_word(pdev, timing, pio_timing[pio]);
/* Can we lose this oddity of the old driver */
pci_read_config_word(pdev, timing, &dummy);
@@ -98,7 +98,7 @@ static void sl82c105_configure_piomode(struct ata_port *ap, struct ata_device *a
* Called to do the PIO mode setup. Our timing registers are shared
* but we want to set the PIO timing by default.
*/
-
+
static void sl82c105_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
sl82c105_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
@@ -112,7 +112,7 @@ static void sl82c105_set_piomode(struct ata_port *ap, struct ata_device *adev)
* Load DMA cycle times into the chip ready for a DMA transfer
* to occur.
*/
-
+
static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
@@ -122,7 +122,7 @@ static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *a
u16 dummy;
int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
int dma = adev->dma_mode - XFER_MW_DMA_0;
-
+
pci_write_config_word(pdev, timing, dma_timing[dma]);
/* Can we lose this oddity of the old driver */
pci_read_config_word(pdev, timing, &dummy);
@@ -137,7 +137,7 @@ static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *a
* for the device in question. Set appropriate PIO timings not DMA
* timings at this point.
*/
-
+
static void sl82c105_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
switch(adev->dma_mode) {
@@ -152,7 +152,7 @@ static void sl82c105_set_dmamode(struct ata_port *ap, struct ata_device *adev)
break;
default:
BUG();
- }
+ }
}
/**
@@ -160,16 +160,16 @@ static void sl82c105_set_dmamode(struct ata_port *ap, struct ata_device *adev)
* @ap: ATA interface
*
* The sl82c105 has some serious problems with the DMA engine
- * when transfers don't run as expected or ATAPI is used. The
+ * when transfers don't run as expected or ATAPI is used. The
* recommended fix is to reset the engine each use using a chip
* test register.
*/
-
+
static void sl82c105_reset_engine(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u16 val;
-
+
pci_read_config_word(pdev, 0x7E, &val);
pci_write_config_word(pdev, 0x7E, val | 4);
pci_write_config_word(pdev, 0x7E, val & ~4);
@@ -180,21 +180,21 @@ static void sl82c105_reset_engine(struct ata_port *ap)
* @qc: ATA command
*
* Reset the DMA engine each use as recommended by the errata
- * document.
+ * document.
*
* FIXME: if we switch clock at BMDMA start/end we might get better
* PIO performance on DMA capable devices.
*/
-
+
static void sl82c105_bmdma_start(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
sl82c105_reset_engine(ap);
-
+
/* Set the clocks for DMA */
sl82c105_configure_dmamode(ap, qc->dev);
- /* Activate DMA */
+ /* Activate DMA */
ata_bmdma_start(qc);
}
@@ -212,14 +212,14 @@ static void sl82c105_bmdma_start(struct ata_queued_cmd *qc)
* We assume bmdma_stop is always called if bmdma_start as called. If
* not then we may need to wrap qc_issue.
*/
-
+
static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
ata_bmdma_stop(qc);
sl82c105_reset_engine(ap);
-
+
/* This will redo the initial setup of the DMA device to matching
PIO timings */
sl82c105_set_dmamode(ap, qc->dev);
@@ -269,11 +269,11 @@ static struct ata_port_operations sl82c105_port_ops = {
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
-
+
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop
-};
+};
/**
* sl82c105_bridge_revision - find bridge version
@@ -283,7 +283,7 @@ static struct ata_port_operations sl82c105_port_ops = {
* providing it is a Winbond 553 reports the revision. If it cannot
* find a revision or the right device it returns -1
*/
-
+
static int sl82c105_bridge_revision(struct pci_dev *pdev)
{
struct pci_dev *bridge;
@@ -315,7 +315,7 @@ static int sl82c105_bridge_revision(struct pci_dev *pdev)
return rev;
}
-
+
static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
static struct ata_port_info info_dma = {
@@ -336,7 +336,7 @@ static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id
int rev;
rev = sl82c105_bridge_revision(dev);
-
+
if (rev == -1)
dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Unable to find bridge, disabling DMA.\n");
else if (rev <= 5)
@@ -345,7 +345,7 @@ static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id
port_info[0] = &info_dma;
port_info[1] = &info_dma;
}
-
+
pci_read_config_dword(dev, 0x40, &val);
val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
pci_write_config_dword(dev, 0x40, val);