diff options
Diffstat (limited to 'drivers/gpio/Kconfig')
| -rw-r--r-- | drivers/gpio/Kconfig | 216 |
1 files changed, 184 insertions, 32 deletions
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 1301cec94f12..44f922e10db2 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -70,8 +70,7 @@ config GPIO_SYSFS ioctl() operations instead. config GPIO_CDEV - bool - prompt "Character device (/dev/gpiochipN) support" if EXPERT + bool "Character device (/dev/gpiochipN) support" if EXPERT default y help Say Y here to add the character device /dev/gpiochipN interface @@ -103,6 +102,15 @@ config GPIO_REGMAP select REGMAP tristate +config GPIO_SWNODE_UNDEFINED + bool + help + This adds a special place holder for software nodes to contain an + undefined GPIO reference, this is primarily used by SPI to allow a + list of GPIO chip selects to mark a certain chip select as being + controlled the SPI device's internal chip select mechanism and not + a GPIO. + # put drivers in the right section, in alphabetical order # This symbol is selected by both I2C and SPI expanders @@ -140,9 +148,7 @@ config GPIO_74XX_MMIO config GPIO_ALTERA tristate "Altera GPIO" - depends on OF_GPIO select GPIOLIB_IRQCHIP - select OF_GPIO_MM_GPIOCHIP help Say Y or M here to build support for the Altera PIO device. @@ -195,6 +201,7 @@ config GPIO_RASPBERRYPI_EXP config GPIO_BCM_KONA bool "Broadcom Kona GPIO" depends on ARCH_BCM_MOBILE || COMPILE_TEST + select GPIOLIB_IRQCHIP help Turn on GPIO support for Broadcom "Kona" chips. @@ -207,10 +214,22 @@ config GPIO_BCM_XGS_IPROC help Say yes here to enable GPIO support for Broadcom XGS iProc SoCs. +config GPIO_BLZP1600 + tristate "Blaize BLZP1600 GPIO support" + default y if ARCH_BLAIZE + depends on ARCH_BLAIZE || COMPILE_TEST + depends on OF_GPIO + select GPIO_GENERIC + select GPIOLIB_IRQCHIP + help + Say Y or M here to add support for the Blaize BLZP1600 GPIO device. + The controller is based on the Verisilicon Microelectronics GPIO APB v0.2 + IP block. + config GPIO_BRCMSTB tristate "BRCMSTB GPIO support" default y if (ARCH_BRCMSTB || BMIPS_GENERIC) - depends on OF_GPIO && (ARCH_BRCMSTB || BMIPS_GENERIC || COMPILE_TEST) + depends on OF_GPIO && (ARCH_BRCMSTB || ARCH_BCM2835 || BMIPS_GENERIC || COMPILE_TEST) select GPIO_GENERIC select IRQ_DOMAIN help @@ -234,7 +253,8 @@ config GPIO_CLPS711X config GPIO_DAVINCI tristate "TI Davinci/Keystone GPIO support" default y if ARCH_DAVINCI - depends on (ARM || ARM64) && (ARCH_DAVINCI || ARCH_KEYSTONE || ARCH_K3) + depends on ((ARM || ARM64) && (ARCH_DAVINCI || ARCH_KEYSTONE || ARCH_K3)) || COMPILE_TEST + select GPIOLIB_IRQCHIP help Say yes here to enable GPIO support for TI Davinci/Keystone SoCs. @@ -312,11 +332,29 @@ config GPIO_GENERIC_PLATFORM help Say yes here to support basic platform_device memory-mapped GPIO controllers. +config GPIO_GRANITERAPIDS + tristate "Intel Granite Rapids-D vGPIO support" + depends on X86 || COMPILE_TEST + select GPIOLIB_IRQCHIP + help + Select this to enable virtual GPIO support on platforms with the + following SoCs: + + - Intel Granite Rapids-D + + The driver enables basic GPIO functionality and implements interrupt + support. The virtual GPIO driver controls GPIO lines via a firmware + interface. The physical GPIO pins reside on device that is external + from the main SoC package, such as a BMC or a CPLD. + + To compile this driver as a module, choose M here: the module will + be called gpio-graniterapids. + config GPIO_GRGPIO tristate "Aeroflex Gaisler GRGPIO support" - depends on OF_GPIO + depends on OF || COMPILE_TEST select GPIO_GENERIC - select IRQ_DOMAIN + select GPIOLIB_IRQCHIP help Select this to support Aeroflex Gaisler GRGPIO cores from the GRLIB VHDL IP core library. @@ -344,8 +382,7 @@ config GPIO_HLWD config GPIO_ICH tristate "Intel ICH GPIO" - depends on X86 - depends on LPC_ICH + depends on (X86 && LPC_ICH) || (COMPILE_TEST && HAS_IOPORT) help Say yes here to support the GPIO functionality of a number of Intel ICH-based chipsets. Currently supported devices: ICH6, ICH7, ICH8 @@ -401,6 +438,7 @@ config GPIO_LPC18XX default y if ARCH_LPC18XX depends on OF_GPIO && (ARCH_LPC18XX || COMPILE_TEST) select IRQ_DOMAIN_HIERARCHY + select GPIOLIB_IRQCHIP help Select this option to enable GPIO driver for NXP LPC18XX/43XX devices. @@ -444,7 +482,7 @@ config GPIO_MPC8XXX FSL_SOC_BOOKE || PPC_86xx || ARCH_LAYERSCAPE || ARM || \ COMPILE_TEST select GPIO_GENERIC - select IRQ_DOMAIN + select GPIOLIB_IRQCHIP help Say Y here if you're going to use hardware that connects to the MPC512x/831x/834x/837x/8572/8610/QorIQ GPIOs. @@ -459,9 +497,9 @@ config GPIO_MT7621 Say yes here to support the Mediatek MT7621 SoC GPIO device. config GPIO_MVEBU - def_bool y - depends on PLAT_ORION || ARCH_MVEBU - depends on OF_GPIO + bool "Marvell Orion and EBU GPIO support" if COMPILE_TEST + depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST + default PLAT_ORION || ARCH_MVEBU select GENERIC_IRQ_CHIP select REGMAP_MMIO @@ -478,6 +516,18 @@ config GPIO_MXS select GPIO_GENERIC select GENERIC_IRQ_CHIP +config GPIO_NOMADIK + bool "Nomadik GPIO driver" + depends on ARCH_U8500 || ARCH_NOMADIK || MACH_EYEQ5 || COMPILE_TEST + select GPIOLIB_IRQCHIP + help + Say yes here to support the Nomadik SoC GPIO block. This block is also + used by the Mobileye EyeQ5 SoC. + + It handles up to 32 GPIOs per bank, that can all be interrupt sources. + It is deeply interconnected with the associated pinctrl driver as GPIO + registers handle muxing ("alternate functions") as well. + config GPIO_NPCM_SGPIO bool "Nuvoton SGPIO support" depends on ARCH_NPCM || COMPILE_TEST @@ -494,9 +544,9 @@ config GPIO_OCTEON family of SOCs. config GPIO_OMAP - tristate "TI OMAP GPIO support" if ARCH_OMAP2PLUS || COMPILE_TEST + tristate "TI OMAP GPIO support" + depends on ARCH_OMAP || COMPILE_TEST default y if ARCH_OMAP - depends on ARM select GENERIC_IRQ_CHIP select GPIOLIB_IRQCHIP help @@ -504,15 +554,22 @@ config GPIO_OMAP config GPIO_PL061 tristate "PrimeCell PL061 GPIO support" - depends on ARM_AMBA + depends on ARM_AMBA || COMPILE_TEST select IRQ_DOMAIN select GPIOLIB_IRQCHIP help Say yes here to support the PrimeCell PL061 GPIO device. +config GPIO_POLARFIRE_SOC + bool "Microchip FPGA GPIO support" + select REGMAP_MMIO + help + Say yes here to support the GPIO controllers on Microchip FPGAs. + config GPIO_PXA bool "PXA GPIO support" depends on ARCH_PXA || ARCH_MMP || COMPILE_TEST + select GPIOLIB_IRQCHIP help Say yes here to support the PXA GPIO device. @@ -562,7 +619,7 @@ config GPIO_ROCKCHIP config GPIO_RTD tristate "Realtek DHC GPIO support" - depends on ARCH_REALTEK + depends on ARCH_REALTEK || COMPILE_TEST default y select GPIOLIB_IRQCHIP help @@ -614,6 +671,15 @@ config GPIO_SNPS_CREG where only several fields in register belong to GPIO lines and each GPIO line owns a field with different length and on/off value. +config GPIO_SPACEMIT_K1 + tristate "SPACEMIT K1 GPIO support" + depends on ARCH_SPACEMIT || COMPILE_TEST + depends on OF_GPIO + select GPIO_GENERIC + select GPIOLIB_IRQCHIP + help + Say yes here to support the SpacemiT's K1 GPIO device. + config GPIO_SPEAR_SPICS bool "ST SPEAr13xx SPI Chip Select as GPIO support" depends on PLAT_SPEAR @@ -675,13 +741,13 @@ config GPIO_TEGRA config GPIO_TEGRA186 tristate "NVIDIA Tegra186 GPIO support" - default ARCH_TEGRA_186_SOC || ARCH_TEGRA_194_SOC - depends on ARCH_TEGRA_186_SOC || ARCH_TEGRA_194_SOC || COMPILE_TEST + default ARCH_TEGRA_186_SOC || ARCH_TEGRA_194_SOC || ARCH_TEGRA_234_SOC + depends on ARCH_TEGRA_186_SOC || ARCH_TEGRA_194_SOC || ARCH_TEGRA_234_SOC || COMPILE_TEST depends on OF_GPIO select GPIOLIB_IRQCHIP select IRQ_DOMAIN_HIERARCHY help - Say yes here to support GPIO pins on NVIDIA Tegra186 SoCs. + Say yes here to support GPIO pins on NVIDIA Tegra186, 194 and 234 SoCs. config GPIO_TS4800 tristate "TS-4800 DIO blocks and compatibles" @@ -711,9 +777,11 @@ config GPIO_UNIPHIER Say yes here to support UniPhier GPIOs. config GPIO_VF610 - def_bool y - depends on ARCH_MXC + tristate "VF610 GPIO support" + default y if SOC_VF610 + depends on ARCH_MXC || COMPILE_TEST select GPIOLIB_IRQCHIP + select GPIO_GENERIC help Say yes here to support i.MX or Vybrid vf610 GPIOs. @@ -756,7 +824,6 @@ config GPIO_XGENE_SB config GPIO_XILINX tristate "Xilinx GPIO support" select GPIOLIB_IRQCHIP - depends on OF_GPIO help Say yes here to support the Xilinx FPGA GPIO device. @@ -787,14 +854,14 @@ config GPIO_ZEVIO config GPIO_ZYNQ tristate "Xilinx Zynq GPIO support" - depends on ARCH_ZYNQ || ARCH_ZYNQMP + depends on ARCH_ZYNQ || ARCH_ZYNQMP || COMPILE_TEST select GPIOLIB_IRQCHIP help Say yes here to support Xilinx Zynq GPIO controller. config GPIO_ZYNQMP_MODEPIN tristate "ZynqMP ps-mode pin GPIO configuration driver" - depends on ZYNQMP_FIRMWARE + depends on ZYNQMP_FIRMWARE || COMPILE_TEST default ZYNQMP_FIRMWARE help Say yes here to support the ZynqMP ps-mode pin GPIO configuration @@ -823,7 +890,7 @@ config GPIO_AMD_FCH config GPIO_MSC313 bool "MStar MSC313 GPIO support" - depends on ARCH_MSTARV7 + depends on ARCH_MSTARV7 || COMPILE_TEST default ARCH_MSTARV7 select GPIOLIB_IRQCHIP select IRQ_DOMAIN_HIERARCHY @@ -1193,6 +1260,13 @@ config GPIO_ADP5520 This option enables support for on-chip GPIO found on Analog Devices ADP5520 PMICs. +config GPIO_ADP5585 + tristate "GPIO Support for ADP5585" + depends on MFD_ADP5585 + help + This option enables support for the GPIO function found in the Analog + Devices ADP5585. + config GPIO_ALTERA_A10SR tristate "Altera Arria10 System Resource GPIO" depends on MFD_ALTERA_A10SR @@ -1240,6 +1314,26 @@ config GPIO_BD9571MWV This driver can also be built as a module. If so, the module will be called gpio-bd9571mwv. +config GPIO_CGBC + tristate "Congatec Board Controller GPIO support" + depends on MFD_CGBC + help + Select this option to enable GPIO support for the Congatec Board + Controller. + + This driver can also be built as a module. If so, the module will be + called gpio-cgbc. + +config GPIO_CROS_EC + tristate "ChromeOS EC GPIO support" + depends on CROS_EC + help + GPIO driver for the ChromeOS Embedded Controller (EC). GPIOs + cannot be set unless the system is unlocked. + + This driver can also be built as a module. If so, the module + will be called gpio-cros-ec. + config GPIO_CRYSTAL_COVE tristate "GPIO support for Crystal Cove PMIC" depends on (X86 || COMPILE_TEST) && INTEL_SOC_PMIC @@ -1295,7 +1389,7 @@ config GPIO_DLN2 config HTC_EGPIO bool "HTC EGPIO support" - depends on ARM + depends on ARM || COMPILE_TEST help This driver supports the CPLD egpio chip present on several HTC phones. It provides basic support for input @@ -1393,6 +1487,19 @@ config GPIO_MAX77650 GPIO driver for MAX77650/77651 PMIC from Maxim Semiconductor. These chips have a single pin that can be configured as GPIO. +config GPIO_MAX77759 + tristate "Maxim Integrated MAX77759 GPIO support" + depends on MFD_MAX77759 + default MFD_MAX77759 + select GPIOLIB_IRQCHIP + help + GPIO driver for MAX77759 PMIC from Maxim Integrated. + There are two GPIOs available on these chips in total, both of + which can also generate interrupts. + + This driver can also be built as a module. If so, the module will be + called gpio-max77759. + config GPIO_PALMAS bool "TI PALMAS series PMICs GPIO" depends on MFD_PALMAS @@ -1450,12 +1557,13 @@ config GPIO_TC3589X config GPIO_TIMBERDALE bool "Support for timberdale GPIO IP" depends on MFD_TIMBERDALE + select GPIOLIB_IRQCHIP help Add support for the GPIO IP in the timberdale FPGA. config GPIO_TN48M_CPLD tristate "Delta Networks TN48M switch CPLD GPIO driver" - depends on MFD_TN48M_CPLD + depends on MFD_TN48M_CPLD || COMPILE_TEST select GPIO_REGMAP help This enables support for the GPIOs found on the Delta @@ -1526,7 +1634,7 @@ config GPIO_TPS68470 are "output only" GPIOs. config GPIO_TQMX86 - tristate "TQ-Systems QTMX86 GPIO" + tristate "TQ-Systems TQMx86 GPIO" depends on MFD_TQMX86 || COMPILE_TEST depends on HAS_IOPORT_MAP select GPIOLIB_IRQCHIP @@ -1601,7 +1709,7 @@ config GPIO_AMD8111 config GPIO_BT8XX tristate "BT8XX GPIO abuser" - depends on VIDEO_BT848=n + depends on VIDEO_BT848=n || COMPILE_TEST help The BT8xx frame grabber chip has 24 GPIO pins that can be abused as a cheap PCI GPIO card. @@ -1722,7 +1830,6 @@ menu "SPI GPIO expanders" config GPIO_74X164 tristate "74x164 serial-in/parallel-out 8-bits shift register" - depends on OF_GPIO help Driver for 74x164 compatible serial-in/parallel-out 8-outputs shift registers. This driver can be used to provide access @@ -1787,12 +1894,21 @@ config GPIO_VIPERBOARD River Tech's viperboard.h for detailed meaning of the module parameters. +config GPIO_MPSSE + tristate "FTDI MPSSE GPIO support" + select GPIOLIB_IRQCHIP + help + GPIO driver for FTDI's MPSSE interface. These can do input and + output. Each MPSSE provides 16 IO pins. + endmenu menu "Virtual GPIO drivers" config GPIO_AGGREGATOR tristate "GPIO Aggregator" + select CONFIGFS_FS + select DEV_SYNC_PROBE help Say yes here to enable the GPIO Aggregator, which provides a way to aggregate existing GPIO lines into a new virtual GPIO chip. @@ -1835,10 +1951,46 @@ config GPIO_SIM tristate "GPIO Simulator Module" select IRQ_SIM select CONFIGFS_FS + select DEV_SYNC_PROBE help This enables the GPIO simulator - a configfs-based GPIO testing driver. endmenu +menu "GPIO Debugging utilities" + +config GPIO_SLOPPY_LOGIC_ANALYZER + tristate "Sloppy GPIO logic analyzer" + depends on (GPIOLIB || COMPILE_TEST) && CPUSETS && DEBUG_FS && EXPERT + help + This option enables support for a sloppy logic analyzer using polled + GPIOs. Use the 'tools/gpio/gpio-sloppy-logic-analyzer' script with + this driver. The script will make it easier to use and will also + isolate a CPU for the polling task. Note that this is a last resort + analyzer which can be affected by latencies, non-deterministic code + paths, or NMIs. However, for e.g. remote development, it may be useful + to get a first view and aid further debugging. + + If this driver is built as a module it will be called + 'gpio-sloppy-logic-analyzer'. + +config GPIO_VIRTUSER + tristate "GPIO Virtual User Testing Module" + select DEBUG_FS + select CONFIGFS_FS + select IRQ_WORK + select DEV_SYNC_PROBE + help + Say Y here to enable the configurable, configfs-based virtual GPIO + consumer testing driver. + + This driver is aimed as a helper in spotting any regressions in + hot-unplug handling in GPIOLIB. + +endmenu + endif + +config DEV_SYNC_PROBE + tristate |