diff options
Diffstat (limited to 'drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c')
| -rw-r--r-- | drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c | 37 |
1 files changed, 30 insertions, 7 deletions
diff --git a/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c b/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c index 78192ecba102..eb2755bdb30e 100644 --- a/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c +++ b/drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c @@ -1566,6 +1566,10 @@ static enum dc_status apply_single_controller_ctx_to_hw( &pipe_ctx->stream->audio_info); } + /* make sure no pipes syncd to the pipe being enabled */ + if (!pipe_ctx->stream->apply_seamless_boot_optimization && dc->config.use_pipe_ctx_sync_logic) + check_syncd_pipes_for_disabled_master_pipe(dc, context, pipe_ctx->pipe_idx); + #if defined(CONFIG_DRM_AMD_DC_DCN) /* DCN3.1 FPGA Workaround * Need to enable HPO DP Stream Encoder before setting OTG master enable. @@ -1604,11 +1608,6 @@ static enum dc_status apply_single_controller_ctx_to_hw( pipe_ctx->stream_res.stream_enc, pipe_ctx->stream_res.tg->inst); - if (dc_is_dp_signal(pipe_ctx->stream->signal) && - pipe_ctx->stream_res.stream_enc->funcs->reset_fifo) - pipe_ctx->stream_res.stream_enc->funcs->reset_fifo( - pipe_ctx->stream_res.stream_enc); - if (dc_is_dp_signal(pipe_ctx->stream->signal)) dp_source_sequence_trace(link, DPCD_SOURCE_SEQ_AFTER_CONNECT_DIG_FE_OTG); @@ -1835,9 +1834,29 @@ void dce110_enable_accelerated_mode(struct dc *dc, struct dc_state *context) break; } } - // We are trying to enable eDP, don't power down VDD - if (can_apply_edp_fast_boot) + + /* + * TO-DO: So far the code logic below only addresses single eDP case. + * For dual eDP case, there are a few things that need to be + * implemented first: + * + * 1. Change the fastboot logic above, so eDP link[0 or 1]'s + * stream[0 or 1] will all be checked. + * + * 2. Change keep_edp_vdd_on to an array, and maintain keep_edp_vdd_on + * for each eDP. + * + * Once above 2 things are completed, we can then change the logic below + * correspondingly, so dual eDP case will be fully covered. + */ + + // We are trying to enable eDP, don't power down VDD if eDP stream is existing + if ((edp_stream_num == 1 && edp_streams[0] != NULL) || can_apply_edp_fast_boot) { keep_edp_vdd_on = true; + DC_LOG_EVENT_LINK_TRAINING("Keep eDP Vdd on\n"); + } else { + DC_LOG_EVENT_LINK_TRAINING("No eDP stream enabled, turn eDP Vdd off\n"); + } } // Check seamless boot support @@ -2297,6 +2316,10 @@ enum dc_status dce110_apply_ctx_to_hw( enum dc_status status; int i; + /* reset syncd pipes from disabled pipes */ + if (dc->config.use_pipe_ctx_sync_logic) + reset_syncd_pipes_from_disabled_pipes(dc, context); + /* Reset old context */ /* look up the targets that have been removed since last commit */ hws->funcs.reset_hw_ctx_wrap(dc, context); |