diff options
Diffstat (limited to 'drivers/mfd/Kconfig')
| -rw-r--r-- | drivers/mfd/Kconfig | 224 |
1 files changed, 177 insertions, 47 deletions
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index e7a6e45b9fac..6fb3768e3d71 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -20,6 +20,18 @@ config MFD_CS5535 This is the core driver for CS5535/CS5536 MFD functions. This is necessary for using the board's GPIO and MFGPT functionality. +config MFD_ADP5585 + tristate "Analog Devices ADP5585 keypad decoder and I/O expander driver" + select MFD_CORE + select REGMAP_I2C + depends on I2C + depends on OF + help + Say yes here to add support for the Analog Devices ADP5585 GPIO + expander, PWM and keypad controller. This includes the I2C driver and + the core APIs _only_, you have to select individual components like + the GPIO and PWM functions under the corresponding menus. + config MFD_ALTERA_A10SR bool "Altera Arria10 DevKit System Resource chip" depends on ARCH_INTEL_SOCFPGA && SPI_MASTER=y && OF @@ -126,7 +138,7 @@ config MFD_AAT2870_CORE config MFD_AT91_USART tristate "AT91 USART Driver" select MFD_CORE - depends on ARCH_AT91 || COMPILE_TEST + depends on ARCH_AT91 || ARCH_LAN969X || COMPILE_TEST help Select this to get support for AT91 USART IP. This is a wrapper over at91-usart-serial driver and usart-spi-driver. Only one function @@ -224,6 +236,18 @@ config MFD_AXP20X_RSB components like regulators or the PEK (Power Enable Key) under the corresponding menus. +config MFD_CGBC + tristate "Congatec Board Controller" + select MFD_CORE + depends on X86 + help + This is the core driver of the Board Controller found on some Congatec + SMARC modules. The Board Controller provides functions like watchdog, + I2C busses, and GPIO controller. + + To compile this driver as a module, choose M here: the module will be + called cgbc-core. + config MFD_CROS_EC_DEV tristate "ChromeOS Embedded Controller multifunction device" select MFD_CORE @@ -292,7 +316,7 @@ config MFD_MADERA_SPI config MFD_MAX5970 tristate "Maxim 5970/5978 power switch and monitor" - depends on (I2C && OF) + depends on I2C && OF select MFD_SIMPLE_MFD_I2C help This driver controls a Maxim 5970/5978 switch via I2C bus. @@ -458,7 +482,7 @@ config MFD_EXYNOS_LPASS config MFD_GATEWORKS_GSC tristate "Gateworks System Controller" - depends on (I2C && OF) + depends on I2C && OF select MFD_CORE select REGMAP_I2C select REGMAP_IRQ @@ -473,7 +497,7 @@ config MFD_GATEWORKS_GSC config MFD_MC13XXX tristate - depends on (SPI_MASTER || I2C) + depends on SPI_MASTER || I2C select MFD_CORE select REGMAP_IRQ help @@ -794,6 +818,18 @@ config MFD_88PM860X select individual components like voltage regulators, RTC and battery-charger under the corresponding menus. +config MFD_88PM886_PMIC + bool "Marvell 88PM886 PMIC" + depends on I2C=y + depends on OF + select REGMAP_I2C + select REGMAP_IRQ + select MFD_CORE + help + This enables support for Marvell 88PM886 Power Management IC. + This includes the I2C driver and the core APIs _only_, you have to + select individual components like onkey under the corresponding menus. + config MFD_MAX14577 tristate "Maxim Semiconductor MAX14577/77836 MUIC + Charger Support" depends on I2C @@ -822,7 +858,7 @@ config MFD_MAX77541 There are regulators and adc. config MFD_MAX77620 - bool "Maxim Semiconductor MAX77620 and MAX20024 PMIC Support" + tristate "Maxim Semiconductor MAX77620 and MAX20024 PMIC Support" depends on I2C=y depends on OF select MFD_CORE @@ -880,6 +916,19 @@ config MFD_MAX77693 additional drivers must be enabled in order to use the functionality of the device. +config MFD_MAX77705 + tristate "Maxim MAX77705 PMIC Support" + depends on I2C + select MFD_CORE + select MFD_SIMPLE_MFD_I2C + help + Say yes here to add support for Maxim Integrated MAX77705 PMIC. + This is a Power Management IC with Charger, safe LDOs, Flash, Haptic + and MUIC controls on chip. + This driver provides common support for accessing the device; + additional drivers must be enabled in order to use the functionality + of the device. + config MFD_MAX77714 tristate "Maxim Semiconductor MAX77714 PMIC Support" depends on I2C @@ -894,6 +943,26 @@ config MFD_MAX77714 drivers must be enabled in order to use each functionality of the device. +config MFD_MAX77759 + tristate "Maxim Integrated MAX77759 PMIC" + depends on I2C + depends on OF + select IRQ_DOMAIN + select MFD_CORE + select REGMAP_I2C + select REGMAP_IRQ + help + Say yes here to add support for Maxim Integrated MAX77759. + This is a companion Power Management IC for USB Type-C applications + with Battery Charger, Fuel Gauge, temperature sensors, USB Type-C + Port Controller (TCPC), NVMEM, and additional GPIO interfaces. + This driver provides common support for accessing the device; + additional drivers must be enabled in order to use the functionality + of the device. + + To compile this driver as a module, choose M here: the module will be + called max77759. + config MFD_MAX77843 bool "Maxim Semiconductor MAX77843 PMIC Support" depends on I2C=y @@ -1083,33 +1152,9 @@ config MFD_RETU Retu and Tahvo are a multi-function devices found on Nokia Internet Tablets (770, N800 and N810). -config MFD_PCF50633 - tristate "NXP PCF50633" - depends on I2C - select REGMAP_I2C - help - Say yes here if you have NXP PCF50633 chip on your board. - This core driver provides register access and IRQ handling - facilities, and registers devices for the various functions - so that function-specific drivers can bind to them. - -config PCF50633_ADC - tristate "NXP PCF50633 ADC" - depends on MFD_PCF50633 - help - Say yes here if you want to include support for ADC in the - NXP PCF50633 chip. - -config PCF50633_GPIO - tristate "NXP PCF50633 GPIO" - depends on MFD_PCF50633 - help - Say yes here if you want to include support GPIO for pins on - the PCF50633 chip. - config MFD_PM8XXX tristate "Qualcomm PM8xxx PMIC chips driver" - depends on (ARM || HEXAGON || COMPILE_TEST) + depends on ARM || HEXAGON || COMPILE_TEST select IRQ_DOMAIN_HIERARCHY select MFD_CORE select REGMAP @@ -1225,7 +1270,7 @@ config MFD_RK8XX select MFD_CORE config MFD_RK8XX_I2C - tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip" + tristate "Rockchip RK805/RK808/RK809/RK816/RK817/RK818 Power Management Chip" depends on I2C && OF select MFD_CORE select REGMAP_I2C @@ -1233,7 +1278,7 @@ config MFD_RK8XX_I2C select MFD_RK8XX help If you say yes here you get support for the RK805, RK808, RK809, - RK817 and RK818 Power Management chips. + RK816, RK817 and RK818 Power Management chips. This driver provides common support for accessing the device through I2C interface. The device supports multiple sub-devices including interrupts, RTC, LDO & DCDC regulators, and onkey. @@ -1267,21 +1312,42 @@ config MFD_RN5T618 functionality of the device. config MFD_SEC_CORE - tristate "Samsung Electronics PMIC Series Support" + tristate + select MFD_CORE + select REGMAP_IRQ + +config MFD_SEC_ACPM + tristate "Samsung Electronics S2MPG1x PMICs" + depends on EXYNOS_ACPM_PROTOCOL + depends on OF + select MFD_SEC_CORE + help + Support for the Samsung Electronics PMICs with ACPM interface. + This is a Power Management IC for mobile applications with buck + converters, various LDOs, power meters, RTC, clock outputs, and + additional GPIOs interfaces. + This driver provides common support for accessing the device; + additional drivers must be enabled in order to use the functionality + of the device. + + To compile this driver as a module, choose M here: the module will be + called sec-acpm. + +config MFD_SEC_I2C + tristate "Samsung Electronics S2MPA/S2MPS1X/S2MPU/S5M series PMICs" depends on I2C=y depends on OF - select MFD_CORE + select MFD_SEC_CORE select REGMAP_I2C - select REGMAP_IRQ help - Support for the Samsung Electronics PMIC devices coming - usually along with Samsung Exynos SoC chipset. + Support for the Samsung Electronics PMIC devices with I2C interface + coming usually along with Samsung Exynos SoC chipset. This driver provides common support for accessing the device, additional drivers must be enabled in order to use the functionality - of the device + of the device. To compile this driver as a module, choose M here: the - module will be called sec-core. + module will be called sec-i2c. Have in mind that important core drivers (like regulators) depend on this driver so building this as a module might require proper initial ramdisk or might not boot up as well in certain scenarios. @@ -1418,7 +1484,7 @@ config MFD_DB8500_PRCMU config MFD_STMPE bool "STMicroelectronics STMPE" - depends on (I2C=y || SPI_MASTER=y) + depends on I2C=y || SPI_MASTER=y depends on OF select MFD_CORE help @@ -1459,12 +1525,6 @@ config STMPE_SPI This is used to enable SPI interface of STMPE endmenu -config MFD_STA2X11 - bool "STMicroelectronics STA2X11" - depends on STA2X11 - select MFD_CORE - select REGMAP_MMIO - config MFD_SUN6I_PRCM bool "Allwinner A31/A23/A33 PRCM controller" depends on ARCH_SUNXI || COMPILE_TEST @@ -1773,6 +1833,7 @@ config TWL4030_CORE bool "TI TWL4030/TWL5030/TWL6030/TPS659x0 Support" depends on I2C=y select IRQ_DOMAIN + select MFD_CORE select REGMAP_I2C help Say yes here if you have TWL4030 / TWL6030 family chip on your board. @@ -2088,6 +2149,19 @@ config MFD_ROHM_BD957XMUF BD9573MUF Power Management ICs. BD9576 and BD9573 are primarily designed to be used to power R-Car series processors. +config MFD_ROHM_BD96801 + tristate "ROHM BD96801 Power Management IC" + depends on I2C=y + depends on OF + select REGMAP_I2C + select REGMAP_IRQ + select MFD_CORE + help + Select this option to get support for the ROHM BD96801 Power + Management IC. The ROHM BD96801 is a highly scalable Power Management + IC for industrial and automotive use. The BD96801 can be used as a + master PMIC in a chained PMIC solution with suitable companion PMICs. + config MFD_STM32_LPTIMER tristate "Support for STM32 Low-Power Timer" depends on (ARCH_STM32 && OF) || COMPILE_TEST @@ -2115,7 +2189,7 @@ config MFD_STM32_TIMERS config MFD_STPMIC1 tristate "Support for STPMIC1 PMIC" - depends on (I2C=y && OF) + depends on I2C=y && OF select REGMAP_I2C select REGMAP_IRQ select MFD_CORE @@ -2207,6 +2281,7 @@ config MFD_ACER_A500_EC config MFD_QCOM_PM8008 tristate "QCOM PM8008 Power Management IC" depends on I2C && OF + select MFD_CORE select REGMAP_I2C select REGMAP_IRQ help @@ -2242,6 +2317,36 @@ config MCP_UCB1200_TS endmenu +config MFD_CS40L50_CORE + tristate + select MFD_CORE + select FW_CS_DSP + select REGMAP_IRQ + +config MFD_CS40L50_I2C + tristate "Cirrus Logic CS40L50 (I2C)" + select REGMAP_I2C + select MFD_CS40L50_CORE + depends on I2C + help + Select this to support the Cirrus Logic CS40L50 Haptic + Driver over I2C. + + This driver can be built as a module. If built as a module it will be + called "cs40l50-i2c". + +config MFD_CS40L50_SPI + tristate "Cirrus Logic CS40L50 (SPI)" + select REGMAP_SPI + select MFD_CS40L50_CORE + depends on SPI + help + Select this to support the Cirrus Logic CS40L50 Haptic + Driver over SPI. + + This driver can be built as a module. If built as a module it will be + called "cs40l50-spi". + config MFD_VEXPRESS_SYSREG tristate "Versatile Express System Registers" depends on VEXPRESS_CONFIG && GPIOLIB @@ -2305,6 +2410,19 @@ config MFD_INTEL_M10_BMC_PMCI additional drivers must be enabled in order to use the functionality of the device. +config MFD_QNAP_MCU + tristate "QNAP microcontroller unit core driver" + depends on SERIAL_DEV_BUS + select MFD_CORE + help + Select this to get support for the QNAP MCU device found in + several devices of QNAP network attached storage products that + implements additional functionality for the device, like fan + and LED control. + + This driver implements the base serial protocol to talk to the + device and provides functions for the other parts to hook into. + config MFD_RSMU_I2C tristate "Renesas Synchronization Management Unit with I2C" depends on I2C && OF @@ -2333,5 +2451,17 @@ config MFD_RSMU_SPI Additional drivers must be enabled in order to use the functionality of the device. +config MFD_UPBOARD_FPGA + tristate "Support for the AAeon UP board FPGA" + depends on (X86 && ACPI) + select MFD_CORE + help + Select this option to enable the AAEON UP and UP^2 onboard FPGA. + This is the core driver of this FPGA, which has a pin controller and a + LED controller. + + To compile this driver as a module, choose M here: the module will be + called upboard-fpga. + endmenu endif |