diff options
Diffstat (limited to 'drivers/net/wireless/intel/iwlwifi/iwl-config.h')
| -rw-r--r-- | drivers/net/wireless/intel/iwlwifi/iwl-config.h | 10 |
1 files changed, 1 insertions, 9 deletions
diff --git a/drivers/net/wireless/intel/iwlwifi/iwl-config.h b/drivers/net/wireless/intel/iwlwifi/iwl-config.h index 241a9e3f2a1a..02ded22295c1 100644 --- a/drivers/net/wireless/intel/iwlwifi/iwl-config.h +++ b/drivers/net/wireless/intel/iwlwifi/iwl-config.h @@ -86,10 +86,7 @@ enum iwl_nvm_type { #define IWL_DEFAULT_MAX_TX_POWER 22 #define IWL_TX_CSUM_NETIF_FLAGS (NETIF_F_IPV6_CSUM | NETIF_F_IP_CSUM |\ NETIF_F_TSO | NETIF_F_TSO6) -#define IWL_TX_CSUM_NETIF_FLAGS_BZ (NETIF_F_HW_CSUM | NETIF_F_TSO | NETIF_F_TSO6) -#define IWL_CSUM_NETIF_FLAGS_MASK (IWL_TX_CSUM_NETIF_FLAGS | \ - IWL_TX_CSUM_NETIF_FLAGS_BZ | \ - NETIF_F_RXCSUM) +#define IWL_CSUM_NETIF_FLAGS_MASK (IWL_TX_CSUM_NETIF_FLAGS | NETIF_F_RXCSUM) /* Antenna presence definitions */ #define ANT_NONE 0x0 @@ -250,7 +247,6 @@ enum iwl_cfg_trans_ltr_delay { * RFID can be read before deciding the remaining parameters to use. * * @base_params: pointer to basic parameters - * @csr: csr flags and addresses that are different across devices * @device_family: the device family * @umac_prph_offset: offset to add to UMAC periphery address * @xtal_latency: power up latency to get the xtal stabilized @@ -319,7 +315,6 @@ struct iwl_fw_mon_regs { * @non_shared_ant: the antenna that is for WiFi only * @nvm_ver: NVM version * @nvm_calib_ver: NVM calibration version - * @lib: pointer to the lib ops * @ht_params: point to ht parameters * @led_mode: 0=blinking, 1=On(RF On)/Off(RF Off) * @rx_with_siso_diversity: 1x1 device with rx antenna diversity @@ -344,15 +339,12 @@ struct iwl_fw_mon_regs { * @nvm_type: see &enum iwl_nvm_type * @d3_debug_data_base_addr: base address where D3 debug data is stored * @d3_debug_data_length: length of the D3 debug data - * @bisr_workaround: BISR hardware workaround (for 22260 series devices) * @min_txq_size: minimum number of slots required in a TX queue * @uhb_supported: ultra high band channels supported * @min_ba_txq_size: minimum number of slots required in a TX queue which * based on hardware support (HE - 256, EHT - 1K). * @num_rbds: number of receive buffer descriptors to use * (only used for multi-queue capable devices) - * @mac_addr_csr_base: CSR base register for MAC address access, if not set - * assume 0x380 * * We enable the driver to be backward compatible wrt. hardware features. * API differences in uCode shouldn't be handled here but through TLVs |