diff options
Diffstat (limited to 'drivers/tty/serial/8250')
| -rw-r--r-- | drivers/tty/serial/8250/8250_core.c | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_exar.c | 12 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_mtk.c | 18 |
3 files changed, 30 insertions, 2 deletions
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index fc118f649887..cae61d1ebec5 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -524,6 +524,7 @@ static void __init serial8250_isa_init_ports(void) */ up->mcr_mask = ~ALPHA_KLUDGE_MCR; up->mcr_force = ALPHA_KLUDGE_MCR; + serial8250_set_defaults(up); } /* chain base port ops to support Remote Supervisor Adapter */ @@ -547,7 +548,6 @@ static void __init serial8250_isa_init_ports(void) port->membase = old_serial_port[i].iomem_base; port->iotype = old_serial_port[i].io_type; port->regshift = old_serial_port[i].iomem_reg_shift; - serial8250_set_defaults(up); port->irqflags |= irqflag; if (serial8250_isa_config != NULL) diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c index ddb6aeb76dc5..04b9af7ed941 100644 --- a/drivers/tty/serial/8250/8250_exar.c +++ b/drivers/tty/serial/8250/8250_exar.c @@ -326,7 +326,17 @@ static void setup_gpio(struct pci_dev *pcidev, u8 __iomem *p) * devices will export them as GPIOs, so we pre-configure them safely * as inputs. */ - u8 dir = pcidev->vendor == PCI_VENDOR_ID_EXAR ? 0xff : 0x00; + + u8 dir = 0x00; + + if ((pcidev->vendor == PCI_VENDOR_ID_EXAR) && + (pcidev->subsystem_vendor != PCI_VENDOR_ID_SEALEVEL)) { + // Configure GPIO as inputs for Commtech adapters + dir = 0xff; + } else { + // Configure GPIO as outputs for SeaLevel adapters + dir = 0x00; + } writeb(0x00, p + UART_EXAR_MPIOINT_7_0); writeb(0x00, p + UART_EXAR_MPIOLVL_7_0); diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c index f839380c2f4c..98b8a3e30733 100644 --- a/drivers/tty/serial/8250/8250_mtk.c +++ b/drivers/tty/serial/8250/8250_mtk.c @@ -306,8 +306,21 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, } #endif + /* + * Store the requested baud rate before calling the generic 8250 + * set_termios method. Standard 8250 port expects bauds to be + * no higher than (uartclk / 16) so the baud will be clamped if it + * gets out of that bound. Mediatek 8250 port supports speed + * higher than that, therefore we'll get original baud rate back + * after calling the generic set_termios method and recalculate + * the speed later in this method. + */ + baud = tty_termios_baud_rate(termios); + serial8250_do_set_termios(port, termios, old); + tty_termios_encode_baud_rate(termios, baud, baud); + /* * Mediatek UARTs use an extra highspeed register (MTK_UART_HIGHS) * @@ -339,6 +352,11 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, */ spin_lock_irqsave(&port->lock, flags); + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + /* set DLAB we have cval saved in up->lcr from the call to the core */ serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB); serial_dl_write(up, quot); |