summaryrefslogtreecommitdiff
path: root/drivers/tty/serial/8250
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/8250')
-rw-r--r--drivers/tty/serial/8250/8250_mtk.c29
-rw-r--r--drivers/tty/serial/8250/8250_pci.c8
-rw-r--r--drivers/tty/serial/8250/8250_port.c6
3 files changed, 27 insertions, 16 deletions
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index f4a0caa56f84..21053db93ff1 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -37,6 +37,7 @@
#define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */
#define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */
+#define MTK_UART_EFR 38 /* I/O: Extended Features Register */
#define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */
#define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */
#define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */
@@ -53,6 +54,12 @@
#define MTK_UART_TX_TRIGGER 1
#define MTK_UART_RX_TRIGGER MTK_UART_RX_SIZE
+#define MTK_UART_FEATURE_SEL 39 /* Feature Selection register */
+#define MTK_UART_FEAT_NEWRMAP BIT(0) /* Use new register map */
+
+#define MTK_UART_XON1 40 /* I/O: Xon character 1 */
+#define MTK_UART_XOFF1 42 /* I/O: Xoff character 1 */
+
#ifdef CONFIG_SERIAL_8250_DMA
enum dma_rx_status {
DMA_RX_START = 0,
@@ -169,7 +176,7 @@ static void mtk8250_dma_enable(struct uart_8250_port *up)
MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, UART_EFR_ECB);
+ serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
serial_out(up, UART_LCR, lcr);
if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0)
@@ -232,7 +239,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
int lcr = serial_in(up, UART_LCR);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, UART_EFR_ECB);
+ serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
serial_out(up, UART_LCR, lcr);
lcr = serial_in(up, UART_LCR);
@@ -241,7 +248,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR);
serial_out(up, MTK_UART_ESCAPE_EN, 0x00);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, serial_in(up, UART_EFR) &
+ serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) &
(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)));
serial_out(up, UART_LCR, lcr);
mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI |
@@ -255,8 +262,8 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
/*enable hw flow control*/
- serial_out(up, UART_EFR, MTK_UART_EFR_HW_FC |
- (serial_in(up, UART_EFR) &
+ serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC |
+ (serial_in(up, MTK_UART_EFR) &
(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
serial_out(up, UART_LCR, lcr);
@@ -270,12 +277,12 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
/*enable sw flow control */
- serial_out(up, UART_EFR, MTK_UART_EFR_XON1_XOFF1 |
- (serial_in(up, UART_EFR) &
+ serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 |
+ (serial_in(up, MTK_UART_EFR) &
(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
- serial_out(up, UART_XON1, START_CHAR(port->state->port.tty));
- serial_out(up, UART_XOFF1, STOP_CHAR(port->state->port.tty));
+ serial_out(up, MTK_UART_XON1, START_CHAR(port->state->port.tty));
+ serial_out(up, MTK_UART_XOFF1, STOP_CHAR(port->state->port.tty));
serial_out(up, UART_LCR, lcr);
mtk8250_disable_intrs(up, MTK_UART_IER_CTSI|MTK_UART_IER_RTSI);
mtk8250_enable_intrs(up, MTK_UART_IER_XOFFI);
@@ -568,6 +575,10 @@ static int mtk8250_probe(struct platform_device *pdev)
uart.dma = data->dma;
#endif
+ /* Set AP UART new register map */
+ writel(MTK_UART_FEAT_NEWRMAP, uart.port.membase +
+ (MTK_UART_FEATURE_SEL << uart.port.regshift));
+
/* Disable Rate Fix function */
writel(0x0, uart.port.membase +
(MTK_UART_RATE_FIX << uart.port.regshift));
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index e17e97ea86fa..a293e9f107d0 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -2667,7 +2667,7 @@ enum pci_board_num_t {
pbn_panacom2,
pbn_panacom4,
pbn_plx_romulus,
- pbn_endrun_2_4000000,
+ pbn_endrun_2_3906250,
pbn_oxsemi,
pbn_oxsemi_1_3906250,
pbn_oxsemi_2_3906250,
@@ -3195,10 +3195,10 @@ static struct pciserial_board pci_boards[] = {
* signal now many ports are available
* 2 port 952 Uart support
*/
- [pbn_endrun_2_4000000] = {
+ [pbn_endrun_2_3906250] = {
.flags = FL_BASE0,
.num_ports = 2,
- .base_baud = 4000000,
+ .base_baud = 3906250,
.uart_offset = 0x200,
.first_offset = 0x1000,
},
@@ -4115,7 +4115,7 @@ static const struct pci_device_id serial_pci_tbl[] = {
*/
{ PCI_VENDOR_ID_ENDRUN, PCI_DEVICE_ID_ENDRUN_1588,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_endrun_2_4000000 },
+ pbn_endrun_2_3906250 },
/*
* Quatech cards. These actually have configurable clocks but for
* now we just use the default.
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 318af6f13605..1fbd5bf264be 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1675,11 +1675,11 @@ static void serial8250_start_tx(struct uart_port *port)
struct uart_8250_port *up = up_to_u8250p(port);
struct uart_8250_em485 *em485 = up->em485;
- serial8250_rpm_get_tx(up);
-
if (!port->x_char && uart_circ_empty(&port->state->xmit))
return;
+ serial8250_rpm_get_tx(up);
+
if (em485 &&
em485->active_timer == &em485->start_tx_timer)
return;
@@ -3329,7 +3329,7 @@ static void serial8250_console_restore(struct uart_8250_port *up)
serial8250_set_divisor(port, baud, quot, frac);
serial_port_out(port, UART_LCR, up->lcr);
- serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
+ serial8250_out_MCR(up, up->mcr | UART_MCR_DTR | UART_MCR_RTS);
}
/*
generated by cgit (git 2.34.1) at 2024-05-24 11:18:41 +0000