4 files changed, 38 insertions, 41 deletions

diff --git a/drivers/tty/serial/8250/8250_bcm7271.c b/drivers/tty/serial/8250/8250_bcm7271.c
index 7f656fac503f..5163d60756b7 100644
--- a/drivers/tty/serial/8250/8250_bcm7271.c
+++ b/drivers/tty/serial/8250/8250_bcm7271.c
@@ -237,6 +237,7 @@ struct brcmuart_priv {
 	u32		rx_err;
 	u32		rx_timeout;
 	u32		rx_abort;
+	u32		saved_mctrl;
 };
 
 static struct dentry *brcmuart_debugfs_root;
@@ -1133,16 +1134,27 @@ static int brcmuart_remove(struct platform_device *pdev)
 static int __maybe_unused brcmuart_suspend(struct device *dev)
 {
 	struct brcmuart_priv *priv = dev_get_drvdata(dev);
+	struct uart_8250_port *up = serial8250_get_port(priv->line);
+	struct uart_port *port = &up->port;
 
 	serial8250_suspend_port(priv->line);
 	clk_disable_unprepare(priv->baud_mux_clk);
 
+	/*
+	 * This will prevent resume from enabling RTS before the
+	 *  baud rate has been resored.
+	 */
+	priv->saved_mctrl = port->mctrl;
+	port->mctrl = 0;
+
 	return 0;
 }
 
 static int __maybe_unused brcmuart_resume(struct device *dev)
 {
 	struct brcmuart_priv *priv = dev_get_drvdata(dev);
+	struct uart_8250_port *up = serial8250_get_port(priv->line);
+	struct uart_port *port = &up->port;
 	int ret;
 
 	ret = clk_prepare_enable(priv->baud_mux_clk);
@@ -1165,6 +1177,7 @@ static int __maybe_unused brcmuart_resume(struct device *dev)
 		start_rx_dma(serial8250_get_port(priv->line));
 	}
 	serial8250_resume_port(priv->line);
+	port->mctrl = priv->saved_mctrl;
 	return 0;
 }
 
diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
index 31c9e83ea3cb..251f0018ae8c 100644
--- a/drivers/tty/serial/8250/8250_fintek.c
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -290,25 +290,6 @@ static void fintek_8250_set_max_fifo(struct fintek_8250 *pdata)
 	}
 }
 
-static void fintek_8250_goto_highspeed(struct uart_8250_port *uart,
-			      struct fintek_8250 *pdata)
-{
-	sio_write_reg(pdata, LDN, pdata->index);
-
-	switch (pdata->pid) {
-	case CHIP_ID_F81966:
-	case CHIP_ID_F81866: /* set uart clock for high speed serial mode */
-		sio_write_mask_reg(pdata, F81866_UART_CLK,
-			F81866_UART_CLK_MASK,
-			F81866_UART_CLK_14_769MHZ);
-
-		uart->port.uartclk = 921600 * 16;
-		break;
-	default: /* leave clock speed untouched */
-		break;
-	}
-}
-
 static void fintek_8250_set_termios(struct uart_port *port,
 				    struct ktermios *termios,
 				    struct ktermios *old)
@@ -430,7 +411,6 @@ static int probe_setup_port(struct fintek_8250 *pdata,
 
 				fintek_8250_set_irq_mode(pdata, level_mode);
 				fintek_8250_set_max_fifo(pdata);
-				fintek_8250_goto_highspeed(uart, pdata);
 
 				fintek_8250_exit_key(addr[i]);
 
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 5d43de143f33..60f8fffdfd77 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1324,29 +1324,33 @@ pericom_do_set_divisor(struct uart_port *port, unsigned int baud,
 {
 	int scr;
 	int lcr;
-	int actual_baud;
-	int tolerance;
 
-	for (scr = 5 ; scr <= 15 ; scr++) {
-		actual_baud = 921600 * 16 / scr;
-		tolerance = actual_baud / 50;
+	for (scr = 16; scr > 4; scr--) {
+		unsigned int maxrate = port->uartclk / scr;
+		unsigned int divisor = max(maxrate / baud, 1U);
+		int delta = maxrate / divisor - baud;
 
-		if ((baud < actual_baud + tolerance) &&
-			(baud > actual_baud - tolerance)) {
+		if (baud > maxrate + baud / 50)
+			continue;
 
+		if (delta > baud / 50)
+			divisor++;
+
+		if (divisor > 0xffff)
+			continue;
+
+		/* Update delta due to possible divisor change */
+		delta = maxrate / divisor - baud;
+		if (abs(delta) < baud / 50) {
 			lcr = serial_port_in(port, UART_LCR);
 			serial_port_out(port, UART_LCR, lcr | 0x80);
-
-			serial_port_out(port, UART_DLL, 1);
-			serial_port_out(port, UART_DLM, 0);
+			serial_port_out(port, UART_DLL, divisor & 0xff);
+			serial_port_out(port, UART_DLM, divisor >> 8 & 0xff);
 			serial_port_out(port, 2, 16 - scr);
 			serial_port_out(port, UART_LCR, lcr);
 			return;
-		} else if (baud > actual_baud) {
-			break;
 		}
 	}
-	serial8250_do_set_divisor(port, baud, quot, quot_frac);
 }
 static int pci_pericom_setup(struct serial_private *priv,
 		  const struct pciserial_board *board,
@@ -2291,7 +2295,7 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
 		.setup      = pci_pericom_setup_four_at_eight,
 	},
 	{
-		.vendor     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
@@ -2299,6 +2303,13 @@ static struct pci_serial_quirk pci_serial_quirks[] = {
 	},
 	{
 		.vendor     = PCI_VENDOR_ID_ACCESIO,
+		.device     = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
+		.subvendor  = PCI_ANY_ID,
+		.subdevice  = PCI_ANY_ID,
+		.setup      = pci_pericom_setup_four_at_eight,
+	},
+	{
+		.vendor     = PCI_VENDOR_ID_ACCESIO,
 		.device     = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_4,
 		.subvendor  = PCI_ANY_ID,
 		.subdevice  = PCI_ANY_ID,
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 5775cbff8f6e..46e2079ad1aa 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -2024,13 +2024,6 @@ void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
 	struct uart_8250_port *up = up_to_u8250p(port);
 	unsigned char mcr;
 
-	if (port->rs485.flags & SER_RS485_ENABLED) {
-		if (serial8250_in_MCR(up) & UART_MCR_RTS)
-			mctrl |= TIOCM_RTS;
-		else
-			mctrl &= ~TIOCM_RTS;
-	}
-
 	mcr = serial8250_TIOCM_to_MCR(mctrl);
 
 	mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;