summaryrefslogtreecommitdiff
path: root/drivers/tty/serial
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial')
-rw-r--r--drivers/tty/serial/8250/8250_mtk.c29
-rw-r--r--drivers/tty/serial/8250/8250_pci.c8
-rw-r--r--drivers/tty/serial/8250/8250_port.c6
-rw-r--r--drivers/tty/serial/amba-pl011.c9
-rw-r--r--drivers/tty/serial/digicolor-usart.c5
-rw-r--r--drivers/tty/serial/fsl_lpuart.c18
-rw-r--r--drivers/tty/serial/imx.c2
-rw-r--r--drivers/tty/serial/mpc52xx_uart.c20
-rw-r--r--drivers/tty/serial/sc16is7xx.c6
9 files changed, 58 insertions, 45 deletions
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c
index f4a0caa56f84..21053db93ff1 100644
--- a/drivers/tty/serial/8250/8250_mtk.c
+++ b/drivers/tty/serial/8250/8250_mtk.c
@@ -37,6 +37,7 @@
#define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */
#define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */
+#define MTK_UART_EFR 38 /* I/O: Extended Features Register */
#define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */
#define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */
#define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */
@@ -53,6 +54,12 @@
#define MTK_UART_TX_TRIGGER 1
#define MTK_UART_RX_TRIGGER MTK_UART_RX_SIZE
+#define MTK_UART_FEATURE_SEL 39 /* Feature Selection register */
+#define MTK_UART_FEAT_NEWRMAP BIT(0) /* Use new register map */
+
+#define MTK_UART_XON1 40 /* I/O: Xon character 1 */
+#define MTK_UART_XOFF1 42 /* I/O: Xoff character 1 */
+
#ifdef CONFIG_SERIAL_8250_DMA
enum dma_rx_status {
DMA_RX_START = 0,
@@ -169,7 +176,7 @@ static void mtk8250_dma_enable(struct uart_8250_port *up)
MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, UART_EFR_ECB);
+ serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
serial_out(up, UART_LCR, lcr);
if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0)
@@ -232,7 +239,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
int lcr = serial_in(up, UART_LCR);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, UART_EFR_ECB);
+ serial_out(up, MTK_UART_EFR, UART_EFR_ECB);
serial_out(up, UART_LCR, lcr);
lcr = serial_in(up, UART_LCR);
@@ -241,7 +248,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR);
serial_out(up, MTK_UART_ESCAPE_EN, 0x00);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, serial_in(up, UART_EFR) &
+ serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) &
(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)));
serial_out(up, UART_LCR, lcr);
mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI |
@@ -255,8 +262,8 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
/*enable hw flow control*/
- serial_out(up, UART_EFR, MTK_UART_EFR_HW_FC |
- (serial_in(up, UART_EFR) &
+ serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC |
+ (serial_in(up, MTK_UART_EFR) &
(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
serial_out(up, UART_LCR, lcr);
@@ -270,12 +277,12 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode)
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
/*enable sw flow control */
- serial_out(up, UART_EFR, MTK_UART_EFR_XON1_XOFF1 |
- (serial_in(up, UART_EFR) &
+ serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 |
+ (serial_in(up, MTK_UART_EFR) &
(~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))));
- serial_out(up, UART_XON1, START_CHAR(port->state->port.tty));
- serial_out(up, UART_XOFF1, STOP_CHAR(port->state->port.tty));
+ serial_out(up, MTK_UART_XON1, START_CHAR(port->state->port.tty));
+ serial_out(up, MTK_UART_XOFF1, STOP_CHAR(port->state->port.tty));
serial_out(up, UART_LCR, lcr);
mtk8250_disable_intrs(up, MTK_UART_IER_CTSI|MTK_UART_IER_RTSI);
mtk8250_enable_intrs(up, MTK_UART_IER_XOFFI);
@@ -568,6 +575,10 @@ static int mtk8250_probe(struct platform_device *pdev)
uart.dma = data->dma;
#endif
+ /* Set AP UART new register map */
+ writel(MTK_UART_FEAT_NEWRMAP, uart.port.membase +
+ (MTK_UART_FEATURE_SEL << uart.port.regshift));
+
/* Disable Rate Fix function */
writel(0x0, uart.port.membase +
(MTK_UART_RATE_FIX << uart.port.regshift));
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index e17e97ea86fa..a293e9f107d0 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -2667,7 +2667,7 @@ enum pci_board_num_t {
pbn_panacom2,
pbn_panacom4,
pbn_plx_romulus,
- pbn_endrun_2_4000000,
+ pbn_endrun_2_3906250,
pbn_oxsemi,
pbn_oxsemi_1_3906250,
pbn_oxsemi_2_3906250,
@@ -3195,10 +3195,10 @@ static struct pciserial_board pci_boards[] = {
* signal now many ports are available
* 2 port 952 Uart support
*/
- [pbn_endrun_2_4000000] = {
+ [pbn_endrun_2_3906250] = {
.flags = FL_BASE0,
.num_ports = 2,
- .base_baud = 4000000,
+ .base_baud = 3906250,
.uart_offset = 0x200,
.first_offset = 0x1000,
},
@@ -4115,7 +4115,7 @@ static const struct pci_device_id serial_pci_tbl[] = {
*/
{ PCI_VENDOR_ID_ENDRUN, PCI_DEVICE_ID_ENDRUN_1588,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_endrun_2_4000000 },
+ pbn_endrun_2_3906250 },
/*
* Quatech cards. These actually have configurable clocks but for
* now we just use the default.
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 318af6f13605..1fbd5bf264be 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1675,11 +1675,11 @@ static void serial8250_start_tx(struct uart_port *port)
struct uart_8250_port *up = up_to_u8250p(port);
struct uart_8250_em485 *em485 = up->em485;
- serial8250_rpm_get_tx(up);
-
if (!port->x_char && uart_circ_empty(&port->state->xmit))
return;
+ serial8250_rpm_get_tx(up);
+
if (em485 &&
em485->active_timer == &em485->start_tx_timer)
return;
@@ -3329,7 +3329,7 @@ static void serial8250_console_restore(struct uart_8250_port *up)
serial8250_set_divisor(port, baud, quot, frac);
serial_port_out(port, UART_LCR, up->lcr);
- serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
+ serial8250_out_MCR(up, up->mcr | UART_MCR_DTR | UART_MCR_RTS);
}
/*
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 51ecb050ae40..4d11a3e547f9 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -1255,13 +1255,18 @@ static inline bool pl011_dma_rx_running(struct uart_amba_port *uap)
static void pl011_rs485_tx_stop(struct uart_amba_port *uap)
{
+ /*
+ * To be on the safe side only time out after twice as many iterations
+ * as fifo size.
+ */
+ const int MAX_TX_DRAIN_ITERS = uap->port.fifosize * 2;
struct uart_port *port = &uap->port;
int i = 0;
u32 cr;
/* Wait until hardware tx queue is empty */
while (!pl011_tx_empty(port)) {
- if (i == port->fifosize) {
+ if (i > MAX_TX_DRAIN_ITERS) {
dev_warn(port->dev,
"timeout while draining hardware tx queue\n");
break;
@@ -2052,7 +2057,7 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios,
* with the given baud rate. We use this as the poll interval when we
* wait for the tx queue to empty.
*/
- uap->rs485_tx_drain_interval = (bits * 1000 * 1000) / baud;
+ uap->rs485_tx_drain_interval = DIV_ROUND_UP(bits * 1000 * 1000, baud);
pl011_setup_status_masks(port, termios);
diff --git a/drivers/tty/serial/digicolor-usart.c b/drivers/tty/serial/digicolor-usart.c
index 6d70fea76bb3..e37a917b9dbb 100644
--- a/drivers/tty/serial/digicolor-usart.c
+++ b/drivers/tty/serial/digicolor-usart.c
@@ -471,11 +471,10 @@ static int digicolor_uart_probe(struct platform_device *pdev)
if (IS_ERR(uart_clk))
return PTR_ERR(uart_clk);
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- dp->port.mapbase = res->start;
- dp->port.membase = devm_ioremap_resource(&pdev->dev, res);
+ dp->port.membase = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
if (IS_ERR(dp->port.membase))
return PTR_ERR(dp->port.membase);
+ dp->port.mapbase = res->start;
irq = platform_get_irq(pdev, 0);
if (irq < 0)
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 87789872f400..be12fee94db5 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -2664,6 +2664,7 @@ static int lpuart_probe(struct platform_device *pdev)
struct device_node *np = pdev->dev.of_node;
struct lpuart_port *sport;
struct resource *res;
+ irq_handler_t handler;
int ret;
sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL);
@@ -2741,17 +2742,11 @@ static int lpuart_probe(struct platform_device *pdev)
if (lpuart_is_32(sport)) {
lpuart_reg.cons = LPUART32_CONSOLE;
- ret = devm_request_irq(&pdev->dev, sport->port.irq, lpuart32_int, 0,
- DRIVER_NAME, sport);
+ handler = lpuart32_int;
} else {
lpuart_reg.cons = LPUART_CONSOLE;
- ret = devm_request_irq(&pdev->dev, sport->port.irq, lpuart_int, 0,
- DRIVER_NAME, sport);
+ handler = lpuart_int;
}
-
- if (ret)
- goto failed_irq_request;
-
ret = uart_add_one_port(&lpuart_reg, &sport->port);
if (ret)
goto failed_attach_port;
@@ -2773,13 +2768,18 @@ static int lpuart_probe(struct platform_device *pdev)
sport->port.rs485_config(&sport->port, &sport->port.rs485);
+ ret = devm_request_irq(&pdev->dev, sport->port.irq, handler, 0,
+ DRIVER_NAME, sport);
+ if (ret)
+ goto failed_irq_request;
+
return 0;
+failed_irq_request:
failed_get_rs485:
failed_reset:
uart_remove_one_port(&lpuart_reg, &sport->port);
failed_attach_port:
-failed_irq_request:
lpuart_disable_clks(sport);
failed_clock_enable:
failed_out_of_range:
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index fd38e6ed4fda..a2100be8d554 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1448,7 +1448,7 @@ static int imx_uart_startup(struct uart_port *port)
imx_uart_writel(sport, ucr1, UCR1);
ucr4 = imx_uart_readl(sport, UCR4) & ~(UCR4_OREN | UCR4_INVR);
- if (!sport->dma_is_enabled)
+ if (!dma_is_inited)
ucr4 |= UCR4_OREN;
if (sport->inverted_rx)
ucr4 |= UCR4_INVR;
diff --git a/drivers/tty/serial/mpc52xx_uart.c b/drivers/tty/serial/mpc52xx_uart.c
index 8a6958377764..3acc0f185762 100644
--- a/drivers/tty/serial/mpc52xx_uart.c
+++ b/drivers/tty/serial/mpc52xx_uart.c
@@ -436,31 +436,31 @@ static void mpc512x_psc_fifo_init(struct uart_port *port)
out_be32(&FIFO_512x(port)->rximr, MPC512x_PSC_FIFO_ALARM);
}
-static int mpc512x_psc_raw_rx_rdy(struct uart_port *port)
+static unsigned int mpc512x_psc_raw_rx_rdy(struct uart_port *port)
{
return !(in_be32(&FIFO_512x(port)->rxsr) & MPC512x_PSC_FIFO_EMPTY);
}
-static int mpc512x_psc_raw_tx_rdy(struct uart_port *port)
+static unsigned int mpc512x_psc_raw_tx_rdy(struct uart_port *port)
{
return !(in_be32(&FIFO_512x(port)->txsr) & MPC512x_PSC_FIFO_FULL);
}
-static int mpc512x_psc_rx_rdy(struct uart_port *port)
+static unsigned int mpc512x_psc_rx_rdy(struct uart_port *port)
{
return in_be32(&FIFO_512x(port)->rxsr)
& in_be32(&FIFO_512x(port)->rximr)
& MPC512x_PSC_FIFO_ALARM;
}
-static int mpc512x_psc_tx_rdy(struct uart_port *port)
+static unsigned int mpc512x_psc_tx_rdy(struct uart_port *port)
{
return in_be32(&FIFO_512x(port)->txsr)
& in_be32(&FIFO_512x(port)->tximr)
& MPC512x_PSC_FIFO_ALARM;
}
-static int mpc512x_psc_tx_empty(struct uart_port *port)
+static unsigned int mpc512x_psc_tx_empty(struct uart_port *port)
{
return in_be32(&FIFO_512x(port)->txsr)
& MPC512x_PSC_FIFO_EMPTY;
@@ -780,29 +780,29 @@ static void mpc5125_psc_fifo_init(struct uart_port *port)
out_be32(&FIFO_5125(port)->rximr, MPC512x_PSC_FIFO_ALARM);
}
-static int mpc5125_psc_raw_rx_rdy(struct uart_port *port)
+static unsigned int mpc5125_psc_raw_rx_rdy(struct uart_port *port)
{
return !(in_be32(&FIFO_5125(port)->rxsr) & MPC512x_PSC_FIFO_EMPTY);
}
-static int mpc5125_psc_raw_tx_rdy(struct uart_port *port)
+static unsigned int mpc5125_psc_raw_tx_rdy(struct uart_port *port)
{
return !(in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_FULL);
}
-static int mpc5125_psc_rx_rdy(struct uart_port *port)
+static unsigned int mpc5125_psc_rx_rdy(struct uart_port *port)
{
return in_be32(&FIFO_5125(port)->rxsr) &
in_be32(&FIFO_5125(port)->rximr) & MPC512x_PSC_FIFO_ALARM;
}
-static int mpc5125_psc_tx_rdy(struct uart_port *port)
+static unsigned int mpc5125_psc_tx_rdy(struct uart_port *port)
{
return in_be32(&FIFO_5125(port)->txsr) &
in_be32(&FIFO_5125(port)->tximr) & MPC512x_PSC_FIFO_ALARM;
}
-static int mpc5125_psc_tx_empty(struct uart_port *port)
+static unsigned int mpc5125_psc_tx_empty(struct uart_port *port)
{
return in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_EMPTY;
}
diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index e857fb61efbf..5fb201c1b563 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -1238,12 +1238,10 @@ static void sc16is7xx_shutdown(struct uart_port *port)
/* Disable all interrupts */
sc16is7xx_port_write(port, SC16IS7XX_IER_REG, 0);
- /* Disable TX/RX, clear auto RS485 and RTS invert */
+ /* Disable TX/RX */
sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG,
SC16IS7XX_EFCR_RXDISABLE_BIT |
- SC16IS7XX_EFCR_TXDISABLE_BIT |
- SC16IS7XX_EFCR_AUTO_RS485_BIT |
- SC16IS7XX_EFCR_RTS_INVERT_BIT,
+ SC16IS7XX_EFCR_TXDISABLE_BIT,
SC16IS7XX_EFCR_RXDISABLE_BIT |
SC16IS7XX_EFCR_TXDISABLE_BIT);
generated by cgit (git 2.34.1) at 2024-05-24 02:24:12 +0000