diff options
Diffstat (limited to 'include/linux/spi')
| -rw-r--r-- | include/linux/spi/pxa2xx_spi.h | 1 | ||||
| -rw-r--r-- | include/linux/spi/spi-mem.h | 12 | ||||
| -rw-r--r-- | include/linux/spi/spi.h | 32 | ||||
| -rw-r--r-- | include/linux/spi/spi_bitbang.h | 1 |
4 files changed, 41 insertions, 5 deletions
diff --git a/include/linux/spi/pxa2xx_spi.h b/include/linux/spi/pxa2xx_spi.h index c1c59473cef9..6005f0126631 100644 --- a/include/linux/spi/pxa2xx_spi.h +++ b/include/linux/spi/pxa2xx_spi.h @@ -25,6 +25,7 @@ struct dma_chan; struct pxa2xx_spi_controller { u16 num_chipselect; u8 enable_dma; + u8 dma_burst_size; bool is_slave; /* DMA engine specific config */ diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h index 3703d0dcac2e..af9ff2f0f1b2 100644 --- a/include/linux/spi/spi-mem.h +++ b/include/linux/spi/spi-mem.h @@ -295,6 +295,10 @@ int spi_controller_dma_map_mem_op_data(struct spi_controller *ctlr, void spi_controller_dma_unmap_mem_op_data(struct spi_controller *ctlr, const struct spi_mem_op *op, struct sg_table *sg); + +bool spi_mem_default_supports_op(struct spi_mem *mem, + const struct spi_mem_op *op); + #else static inline int spi_controller_dma_map_mem_op_data(struct spi_controller *ctlr, @@ -310,6 +314,14 @@ spi_controller_dma_unmap_mem_op_data(struct spi_controller *ctlr, struct sg_table *sg) { } + +static inline +bool spi_mem_default_supports_op(struct spi_mem *mem, + const struct spi_mem_op *op) +{ + return false; +} + #endif /* CONFIG_SPI_MEM */ int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op); diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index b30e3d13a5ac..f55b20254612 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -143,7 +143,7 @@ struct spi_device { u32 max_speed_hz; u8 chip_select; u8 bits_per_word; - u16 mode; + u32 mode; #define SPI_CPHA 0x01 /* clock phase */ #define SPI_CPOL 0x02 /* clock polarity */ #define SPI_MODE_0 (0|0) /* (original MicroWire) */ @@ -330,6 +330,9 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv) * must fail if an unrecognized or unsupported mode is requested. * It's always safe to call this unless transfers are pending on * the device whose settings are being modified. + * @set_cs_timing: optional hook for SPI devices to request SPI master + * controller for configuring specific CS setup time, hold time and inactive + * delay interms of clock counts * @transfer: adds a message to the controller's transfer queue. * @cleanup: frees controller-specific state * @can_dma: determine whether this controller supports DMA @@ -363,6 +366,7 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv) * @unprepare_transfer_hardware: there are currently no more messages on the * queue so the subsystem notifies the driver that it may relax the * hardware by issuing this call + * * @set_cs: set the logic level of the chip select line. May be called * from interrupt context. * @prepare_message: set up the controller to transfer a single message, @@ -439,13 +443,12 @@ struct spi_controller { u16 dma_alignment; /* spi_device.mode flags understood by this controller driver */ - u16 mode_bits; + u32 mode_bits; /* bitmask of supported bits_per_word for transfers */ u32 bits_per_word_mask; #define SPI_BPW_MASK(bits) BIT((bits) - 1) -#define SPI_BIT_MASK(bits) (((bits) == 32) ? ~0U : (BIT(bits) - 1)) -#define SPI_BPW_RANGE_MASK(min, max) (SPI_BIT_MASK(max) - SPI_BIT_MASK(min - 1)) +#define SPI_BPW_RANGE_MASK(min, max) GENMASK((max) - 1, (min) - 1) /* limits on transfer speed */ u32 min_speed_hz; @@ -489,6 +492,17 @@ struct spi_controller { */ int (*setup)(struct spi_device *spi); + /* + * set_cs_timing() method is for SPI controllers that supports + * configuring CS timing. + * + * This hook allows SPI client drivers to request SPI controllers + * to configure specific CS timing through spi_set_cs_timing() after + * spi_setup(). + */ + void (*set_cs_timing)(struct spi_device *spi, u8 setup_clk_cycles, + u8 hold_clk_cycles, u8 inactive_clk_cycles); + /* bidirectional bulk transfers * * + The transfer() method may not sleep; its main role is @@ -721,6 +735,9 @@ extern void spi_res_release(struct spi_controller *ctlr, * @bits_per_word: select a bits_per_word other than the device default * for this transfer. If 0 the default (from @spi_device) is used. * @cs_change: affects chipselect after this transfer completes + * @cs_change_delay: delay between cs deassert and assert when + * @cs_change is set and @spi_transfer is not the last in @spi_message + * @cs_change_delay_unit: unit of cs_change_delay * @delay_usecs: microseconds to delay after this transfer before * (optionally) changing the chipselect status, then starting * the next transfer or completing this @spi_message. @@ -810,6 +827,11 @@ struct spi_transfer { u8 bits_per_word; u8 word_delay_usecs; u16 delay_usecs; + u16 cs_change_delay; + u8 cs_change_delay_unit; +#define SPI_DELAY_UNIT_USECS 0 +#define SPI_DELAY_UNIT_NSECS 1 +#define SPI_DELAY_UNIT_SCK 2 u32 speed_hz; u16 word_delay; @@ -1297,7 +1319,7 @@ struct spi_board_info { /* mode becomes spi_device.mode, and is essential for chips * where the default of SPI_CS_HIGH = 0 is wrong. */ - u16 mode; + u32 mode; /* ... may need additional spi_device chip config data here. * avoid stuff protocol drivers can set; but include stuff diff --git a/include/linux/spi/spi_bitbang.h b/include/linux/spi/spi_bitbang.h index b7e021b274dc..4444c2a992cb 100644 --- a/include/linux/spi/spi_bitbang.h +++ b/include/linux/spi/spi_bitbang.h @@ -44,6 +44,7 @@ extern int spi_bitbang_setup_transfer(struct spi_device *spi, /* start or stop queue processing */ extern int spi_bitbang_start(struct spi_bitbang *spi); +extern int spi_bitbang_init(struct spi_bitbang *spi); extern void spi_bitbang_stop(struct spi_bitbang *spi); #endif /* __SPI_BITBANG_H */ |