diff options
Diffstat (limited to 'include/linux')
| -rw-r--r-- | include/linux/mfd/as3722.h | 1 | ||||
| -rw-r--r-- | include/linux/pinctrl/pinconf-generic.h | 10 | ||||
| -rw-r--r-- | include/linux/pinctrl/pinctrl.h | 2 |
3 files changed, 11 insertions, 2 deletions
diff --git a/include/linux/mfd/as3722.h b/include/linux/mfd/as3722.h index 16bf8a0dcd97..f654a7a42260 100644 --- a/include/linux/mfd/as3722.h +++ b/include/linux/mfd/as3722.h @@ -314,6 +314,7 @@ #define AS3722_GPIO_IOSF_GPIO_INTERRUPT_IN AS3722_GPIO_IOSF_VAL(3) #define AS3722_GPIO_IOSF_ISINK_PWM_IN AS3722_GPIO_IOSF_VAL(4) #define AS3722_GPIO_IOSF_VOLTAGE_STBY AS3722_GPIO_IOSF_VAL(5) +#define AS3722_GPIO_IOSF_SD0_OUT AS3722_GPIO_IOSF_VAL(6) #define AS3722_GPIO_IOSF_PWR_GOOD_OUT AS3722_GPIO_IOSF_VAL(7) #define AS3722_GPIO_IOSF_Q32K_OUT AS3722_GPIO_IOSF_VAL(8) #define AS3722_GPIO_IOSF_WATCHDOG_IN AS3722_GPIO_IOSF_VAL(9) diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h index fb90ef5eb038..a15f10727eb8 100644 --- a/include/linux/pinctrl/pinconf-generic.h +++ b/include/linux/pinctrl/pinconf-generic.h @@ -61,6 +61,9 @@ * argument is ignored. * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current * passed as argument. The argument is in mA. + * @PIN_CONFIG_INPUT_ENABLE: enable the pin's input. Note that this does not + * affect the pin's ability to drive output. 1 enables input, 0 disables + * input. * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin. * If the argument != 0, schmitt-trigger mode is enabled. If it's 0, * schmitt-trigger mode is disabled. @@ -82,8 +85,10 @@ * operation, if several modes of operation are supported these can be * passed in the argument on a custom form, else just use argument 1 * to indicate low power mode, argument 0 turns low power mode off. - * @PIN_CONFIG_OUTPUT: this will configure the pin in output, use argument - * 1 to indicate high level, argument 0 to indicate low level. + * @PIN_CONFIG_OUTPUT: this will configure the pin as an output. Use argument + * 1 to indicate high level, argument 0 to indicate low level. (Please + * see Documentation/pinctrl.txt, section "GPIO mode pitfalls" for a + * discussion around this parameter.) * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if * you need to pass in custom configurations to the pin controller, use * PIN_CONFIG_END+1 as the base offset. @@ -99,6 +104,7 @@ enum pin_config_param { PIN_CONFIG_DRIVE_OPEN_DRAIN, PIN_CONFIG_DRIVE_OPEN_SOURCE, PIN_CONFIG_DRIVE_STRENGTH, + PIN_CONFIG_INPUT_ENABLE, PIN_CONFIG_INPUT_SCHMITT_ENABLE, PIN_CONFIG_INPUT_SCHMITT, PIN_CONFIG_INPUT_DEBOUNCE, diff --git a/include/linux/pinctrl/pinctrl.h b/include/linux/pinctrl/pinctrl.h index fefb88663975..cc8e1aff0e28 100644 --- a/include/linux/pinctrl/pinctrl.h +++ b/include/linux/pinctrl/pinctrl.h @@ -32,10 +32,12 @@ struct device_node; * pins, pads or other muxable units in this struct * @number: unique pin number from the global pin number space * @name: a name for this pin + * @drv_data: driver-defined per-pin data. pinctrl core does not touch this */ struct pinctrl_pin_desc { unsigned number; const char *name; + void *drv_data; }; /* Convenience macro to define a single named or anonymous pin descriptor */ |